SPECIAL REPAIR TO BLDG NO P 286 NP 22 AMD P 27 AND PROVN OF ONE TOILET ALONGWITH OH TANK AT MIL STN DHRANGADHRA

Amount

Surface Excavation not exceeding 30 Cm deep and averaging 15 Cm deep and getting out in Soft and disintegrated rock complete all as specified and directed.

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth for foundation of pole,laying of cables etc in Hard and dense soil and getting out complete all as specified and directed.

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth n.exc 10 sqm on plan for foundation of pole, laying of cables etc in soft/disintegrated rock and getting out complete all as specified and directed.

Returning filling in including spreading, leveling, watering and well ramming in layer not exc 25 cm complete all as specified and directed.

Returning filling in including spreading, leveling, watering and well ramming in layer not exc 25 cm in soft/distengrated rock complete all as specified and directed.

Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m complete all as specifeid and directed.

M&L for providing dry river sand as in sand cushioning to UG cable including punning gently all as directed. Note : Depth after punning shall be measured and paid.

Removing excavated material not exc 50 mtr and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed.

Removing excavated soft/disintergrated rock to a distance not exc 50 mtr and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed.

Removing excavated material exc. 1.50 km but n exc. 5 km and depositing where directed in Soft/ disintergrated rock

M&L for hard core of gauge exc 63mm but n exc 100mm deposited, spread and levelled in layers n exc 15cm thick watered and rolled/rammed to a true surface completed all as specified and directed.

M&L PCC 1:4:8 type D-2 (40mm graded aggregate) in foundation, sub base, filling and mass concrete complete all as specified and directed.

M&L PCC (1:4:8) C-2 using 40mm graded stone aggregate as in foundation filling and mass concrete as in foundation filling and mass concrete all as completed as directed.

M&L for Cement Concrete type B-2, 1:2:4 using 40 mm graded crushed stone graded agg as in fdn filling and mass concrete (water storage tank platefom) complete all as completed as directed.

M&L for cement concrete type B1, 1:2:4 (using 20mm graded stone aggregate) as in surface channels and drains including providing necessary form work of adquate strength as directed etc complete all as specified and directed. Note : The cost of form work shall deemed to be included in unit rate quoted by the tenderer.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for padestal/coping around poles, including necessary form work, finishing even and smooth without using extra cement, all as specified and directed.

M&L, precast cement concrete Block Masonary with solid blocks type C1, 1:3:6 (20mm graded stone aggregate) exc 10 cm in width and setting in mortar 1:6 complete all as specified and directed .

M&L for providing precast cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in manhole covers including placing the cover in position and set in cement mortar 1:6 complete all as specified and directed. Note : Reinforcement shall be measured and paid seperately.

M&L design mix RCC M-25 (20mm graded stone aggregate) grade concrete in foundation including raft,footing foundations beem ,plinth beams base for coloumn etc complete all as specified and directed.

M&L for RCC 1:1:5:3 type A-1 as in slabs supported on walls, beams and columns in floors, roofs, landings, fixed with tined tacks or galvanized wire staples complete all as specified and directed.

M&L design mix RCC M-25 (using 20 mm graded granite stone aggregate) as in roof slab, projections supported on walls, beams and cloumns in roofs etc. complete all as specified and directed.

M&L design mix RCC M-25 in lintel beams/lintels, roof beams over 1.50 mtr spancomplete all as specified and directed.

M&L design mix RCC M-25 in chajjas etc. complete all as specified and directed.

M&L design mix RCC M-25 (20mm graded stone aggregate) grade concrete in coloumn etc complete all as specified and directed.

Extra for forming fair finished drainor channel 30 CM inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

Add or deduct for each 25mm girth or part thereof over or under 30 cm as directed.

Supply only Integral waterproofing compound complete all as specified and directed.

Supply and laying well burnt best quality locally available bricks for protection of UG cable all as specified and directed.

S&F, sub class 'B' bricks for protection of cable and laid perpendicular to the trenches complete all as specified and directed.

M&L for old size fly ash Brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for fly ash Brick work with old size, sub class 'B' bricks, straight or curved on plan any radius in half brick thick wall built in cement mortar 1:6 complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings in block walls where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 10cm but n.exc. 20cm girth complete all as specified and directed.

M&L for cutting holes into or through concrete walls built in cement of superficial area not exceeding 400 sq. cm but n. exc 0.10 Sqcm including making good and rubbis off the premises complete all as specified and directed.

M&L for walling of random rubble stone masonry, brought up to courses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

M&L for walling of random rubble stone masonry, brought up to courses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

M&L for walling of random rubble, except stone, uncoursed, well bonded, bedded and solidly hearted, built in CM (1:6) complete all as specified and directed.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface n. exc 20mm for sand stone and dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses completed as specified and directed.

Form work to sides of concrete foundations footing bases of coloumn raft and raft beams sides and soffits of plinth beams and similar works vertical or to batter complete all as specified and directed.

Rough finished flat form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exce 200 mm thick complete all as specified and directed.

M&L for formwork to chullah hoods, chajjas, troughs and similar items in cluding edges complete all as specified and directed.

M&L for Form work for to side and soffits of floor or roof beams, beam haunchings, girders bressummers lintels, cantilevers, shelved including sup-ports, overhangs etc also splays between floors and beams etc. complete all as specified and directed.

M&L for form work to sides of pillars, posts, struts, piers, columns and stanchions and rough finished surfaces of concrete all as specified and directed.

Rough finished flat form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exce 200 mm thick complete all as specified and directed.

S&F, 35 mm thick, 2nd class hard wood, factory made, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed.

M&L For 35 mm thick factory made 2nd class HW rail and style Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5 sq.m but not exc. 4 sq.m each complete all as specified and directed.

Taking down old shutters of any description exc. 1 sqm but not exc. 2 sqm each complete all as specified and directed.

S&F, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specifications complete all as specified and directed.

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed

S&F 200 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300 mm and fixed complete all as specified and directed.

S&F, butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified and directed.

S&F, butt hinges, 100 mm long extrucded aluminium alloy with galvanized mild steel hinge pin, anodized and fixed, complete all as specified and directed.

S & F Aluminium handles, cast type, anodised 150 mm long complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

S&F, in repairs, Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nomonal dia of bar and 1.18 mm avrage width of aperture ,fixed with tined tacks or galvanised wire staples complete all as specified and as directed.

S&F, in repair, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to wooden door Shutters/aluminium sliding shutters complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to wooden door Shutters/aluminium sliding shutters complete all as specified and directed.

S&F M.S Framed work such as grills gratings etc with ends of bars sholdered and/or riveted into spikes ,framed guard bars /railings all as directed .

M&L for MS work such as bands, straps, hold fst, clamps, hooks and similar Fe-290 (Gde-E-165) complete all as specified and directed.

S&F in repair mild steel bolts purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends. each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long dia of neck n exc 20mm complete all as specified and directed.

M&L for TMT 10mm dia bar and over, as in stiffeners, cut to length, bent to shape required, including cranking, bending, hooking ends, binding with and incluing mild steel wire(annealed) not less than steel wire 0.9mm dia or securing with clips complete all as specified and directed.

M&L for TMT 6 to 8 mm dia bar, cut to length, bent to shape required, including cranking, bending, hooking ends, binding with and inlcuding mild steel wire (annealed) not less than steel wire 0.9mm dia or securing with clips and confirming to FE-410-S and 310-0) complete all as specified and directed.

M&L for TMT bar 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders of Grade-500d incl cutting, bending, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed0 not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F rolled mild steel section as in main and cross beams hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates conforming to Fe-410, Gde E-250 quality B complete all as specified and directed.

Fixing only rolled mild steel section as in main and cross beams hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates conforming to Fe-290, Gde E-165 all as specified and directed.

S&F, rolled mild steel section as in main and cross beams hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates conforming to Fe-290, Gde E-165 all as specified and directed.

S&F, compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. conforming to Fe-410 W complete all as sepcifeid and directed.

S&F, for gusset plates (Plain or chequered) channels, square cut or notched (ordinary and counter sunk foring hole without any attachement to Fe-290 (Gde E-165) complete all as specified and directed.

Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe-290 Gde E-165 complete all as specified and directed.

Refixing Mild steel (items obtained from dismantling) for roof trusses (framed), trussed purlins, crane gantires, rails and fasternings and heavy bracket framming (beam, tee angle, channel or flat sections) including distance pieces, clats etc. complete all as specied and directed.

M&L for rolled mild steel angle iron work as in door frames complete, drilled for fixing of hinges etc. also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and directed.

S&F factory made steel ventilators with top hung shutter including hinges, steel peg stay, glazing bars including applying one shop coat of red oxide primer all as specified and directed

S&F standard aluminium section powder coated any colour as approved for three track window/door frames/shutters sliding/ partitions etc including jointing cleat and rubber eading/linning, Pivot ,locking aragement and all hardware etc and fixed in position with stainless steel screws all as specified and as directed.

S&F, plain aluminium sheeting 0.56mm thick, alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) complete all as specified and directed.

S&F, in repair, pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of an colour (as approved by GE) having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed.

S&F, APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed

S&F, in repair, false ceiling, at any height, 600 x 600mm grid with Armstrong 'Prelude XL 32' grid system and 16mm thick mineral fibre acoustic tile 'RH - 99 Classic lite' with suspension system complete all as specified and per manufacturer's instruction. Make : Armstrong or equivalent as approved by GE.

S&F, 8mm thick of size 605 x 605mm HSPC (high pressure Stem Cured) pre-primetered self embossed, textured disigner board E-board classic to be fixed anodised alunimium snap grid/section size 605mm x 605mm with main runner, fross tee and wall angle duly suspended with 4mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing procisions for light fixtures of any size complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L for kota stone slab 20mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc and including 10 mm thick backing coat in CM 1:3 complete all as specified and directed.

M&L in repair to Granite (of any type/colour) work (table rubbed and polished) 10 to 20mm thick in steps, jambs, pillars, window cills, cooking platform and like in CM (1:4) including pointing in white cement (1)2( using marble dust with admixture of pigment to match with shade of granite over 15mm thick screed bed in CM 1:6 incl moulding, chamgering of edges complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C2, using 40mm graded stone aggregate as in sub base, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L for 75mm thick cement concrete 1:3:6 type C1, using 40mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L for 75mm Thick Cement Concrete Type D-2, 1:4:8 (40mm Graded Aggregate) complete all as specified and directed.

M&L for 25mm Thick Cement Concrete Type B-1, 1:2:4 (20mm Graded Aggregate) complete all as specified and directed.

M&L, glazed coloured ceramic tiles 200 x 200mm x 7mm thick as in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick backing coat in CM 1:3 complete all as specifed and directed.

M&L for glazed ceramic coloured tiles joint free, any coloured / shed of size 450mm x 300mm x 7mm on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including rendering 10mm thick in cement mortar (1:4), complete all as specified and directed.

M&L for coloured glazed ceramic tiles of size 350x250x7mm / 450x350x7mm thick on vertical surface such as skirting/dado, set and jointed in net cement slurry and pointed in colour cement to match over 10 mm thick backing coat in CM 1:3 complete all as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick joint free tiles, (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick, joint free tiles, (square/ rectangular), area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L for dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as sepcified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar (1:6) on brick work or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar 1:3 on fair faces of concrete finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar 1:3 on fair faces of concrete in ceilings, chajjas, fins facia etc. finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar (1:4) on brick work or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar (1:4) on brick work or concrete surfaces of walls, finished even and smooth without using extra cement mixed with water proofing compound @3% by weight of cement complete all as specified and directed. Note : Integral water proofing compound shall be measured and paid seperately).

M&L for 15mm thick cement plaster on fair faces of birck work or concrete surfaces on wall in CM 1:6 finished the plaster surface fair and even complete all as specified and directed.

M&L for 15mm thick cement plaster on fair faces of birck work or concrete surfaces on external surface of wall in CM 1:4 finish the plaster surface fair and even complete all as specified and directed.

M&L for rendering cement plaster 5mm thick in cement mortar 1:3 on fair faces of concrete in ceilings, chajjas, fins facia etc. complete all as specified and directed.

M&L 15 mm thick rendering in in two layers10mm thick cement plaster in CM 1:6 and 5mm thick in CM 1:4 on fair face of brick work/Stone or concrete surface to be finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:3 on stone masonry surface or surface other than fair face of brick surface finished fair and even without using extra cement mixed with water proofing compound @3% by weight of cement complete all as specified and directed. Note : Integral water proofing compound shall be measured and paid seperately).

M&L for 15mm thick rendering in CM 1:4 on stone masonry surface or surface other than fair face of brick surface finished fair and even without using extra cement mixed with water proofing compound @3% by weight of cement complete all as specified and directed. Note : Integral water proofing compound shall be measured and paid seperately).

M&L for 15mm thick rendering in CM 1:6 on stone masonry surface or surface other than fair face of brickwork surface finished fair and even without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in two layers, 10mm thick in CM 1. 6 and 5mm thick in CM 1:4 on stone masonry surface or surface other than fair face of brickwork surface finished lair and even without using extra Cement complete all as specified and directed.

M&L for taking down , chipping and removing the loose, spailt, damaged cement concrete, cement mortor surfaces of RCC Columns, beams, walls, chajjah etc and exposing the reinforced cement , wire brushing and cleaning the exposed steel reinforced bar, applying rust remover over the cleaned re-bar surface wash the re-bar with clean water for removing all rusts from the old re-bar surfaces, fixing new reinforcement for strengthen the members as required, applying two coats of epoxy zinc primer on new and old steel surfaces, saturate the substrate with water applying one coat of polymer modified bond coat on affected concrete surfaces and finally providing polymer modified cement and quartz sand mortor in CM 1:3 mix , 40mm thk in two coats, using polymer SBR Latex or equivalent as approved @ 5 Ltrs per 50 Kg bag of cement complete all as per manufacturer's Specifications/instructions and as directed. Note :-( New reinforcement (Welded wire fabric) will be measured and paid separately) Make : Dr. Fixit/Sunanda/chemestik/Fosrok

S&F welded steel wire fabric, cut to length, fixed to steel members/reinforcement steel, weight per Sqm not exc. 4 Kg complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for preparation of new surfaces of plastered or unplastered of wall and application of three coat of white washing complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying two coats of oil bound distamper.

M&L for prepration of new/old surfaces of ceilling and applying two coat of oil bound distemper coplete all as specified and directed..

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement primer complete all as specified and directed.

M&L for preparation of old plastered surface of wall and applying one coat of cement base paint complete all as specified and directed.

M&L preperation of new surfaces of walls and applying two coats of oil bound distemper over a coat alkali-resistant primer etc completed all as directed and specified.

M&L for preparing of plastered or unplastered old decorated surfaces of walls by complete removal of existing treatment, moulds, moss and efflorescent salt and treating oil and greasy spot and applying three coat of white wash on walls including cornices etc complete all as specified and directed.

M&L for preparing of new plastered or un-plastered surfaces and applylng two coats of oil bound distemper over a coat of primer over and including wall care pulty complete all as specified and directed

M&L for preparing new plastered or un-plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for preparing old plastered or un-plastered surfaces and applying two coat of white wash on ceilings complete all as specified and directed.

M&L for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc. 0.5 sq.m in each pane complete all as specified and directed.

S&F, 4.8 mm thick plain sheet glass, ordinary quality and glazing not exceeding 0.8 Sqm in each pane fixed with glass putty complet all as specified and directed.

S&F 3mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq.m in each pane

Hacking out old broken glass (any thickness, size, quality or description) not exc 0.5 Sqm each pane from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all,as specified and directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of old wooden surface of any description, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

M&L, preparation old previously treated steel Surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint on the steel surfaces, complete all as specified and directed.

S&F, steel water tubes with rubber gasket at end of each pieces of pipe, light grade, galvanized, with all fittings of size 40mm dia laid in floors/trenches/fixed with poles for protection of cable complete all as specified and directed.

S&F, GI tubing, 20mm bore, medium grade, ISI marked with all necessary fittings, laid in trenches/floors complete all as specified and directed.

S&F, GI tubing, 25mm bore, medium grade, ISI marked with all necessary fittings, laid in trenches/floors complete all as specified and directed.

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 15mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 20mm bore of pipe complete all as specified and directed.

M&L for cutting of road for laying of LT cable and making good to match with the existing using extra cement etc. complete all as specified and directed.

M&L for RCC NP3 150mm dia pipes laid on 150mm thick PCC Cradle PCC 1:4:8 bed with excavation in depth 0.70m - 1.65m in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/RCC/Precast RCC with DFRC ventilating cover and frame includes all items and activities to execute and make sewer line functional.

M&L for construction of birck masonary valve pit of size 600x600x600mm (internal dimension) with brick work in cement mortar (1:4) including excavation and earth work, concrete work, 3mm thick MS sheet cover with locking arrangement, hinges and handle incl angle iron frame, rendering work painting to all steel surfaces with two coats of black bitumenious paint over a coat of red oxide primer complete and including demolition of existing damaged valve pit.

M&L for cutting of existing CI/GI pipe line for taking branch connecting by necessary cutting/welding work, providing GI fittings such as tee/reducers etc upto 40mm bore complete including necessary earth work complete all as specified and directed.

Disconnecting existing tanks, n. exc 500 litres, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately) complete all as specified and directed.

Supply, hoisting and fixing in position in repairs, 500 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top) including dismantling of old PVC/AC water storage tank of 500 liter capacity complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks of capacity 1000 Litres (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR-Part-I complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks of capacity 1000 Litres (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR-Part-I complete all as specified and directed.

S&F, in repair, 15mm bib taps, chromium plated, cast copper alloy with crutch or butterfly ,handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F, 15mm bib taps, chromium plated, cast copper alloy with crutch or butterfly ,handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F 15mm dia Brass CP bib cock cast copper alloy fancy type with long shank capstain head serewed down high pressure pipe in repairs complete all as specified and directed.

S&F, pillar taps cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed 15 mm bore dia complete all as specified and directed

S&F, pillar taps fancy type cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed 15 mm bore dia complete all as specified and directed.

S&F in chromium plated Stop Valves (Angle type) fancy type 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as directed.

S&F, in repair, 15mm, stop valve/angle valve, cast copper alloy, chromium plated, fency type with crutch or butterfly handle screw down, serewed for iron pipe or brass ferrule complete all as specified and directed.

S&F, 15mm dia stop valves cast copper alloy fancy type chromium plated with long shank and cup (conceled type) screwed down, high pressure with capstain head , screwed both ends, fixed complete all as specified and directed.

S&F, Gun metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe for 25 mm bore of pipe complete all as specified and directed.

S&F, in repair, Gun metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe for 25 mm bore of pipe complete all as specified and directed.

S&F, 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight -210 Gms) complete, all as specified and directed.

S&F in repair 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight -210 Gms) complete, all as specified and directed.

S&F, Swivel shower of PTMT any colour for fixing with 15mm pipe (Minimum weight 40gms) with Shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour.(Minimum weight 40gms complete all as specified and directed.

S&F, Gratting square 150mm size of PTMT (Minum weight 100 gms) complete all as specified and directed.

S&F, Gratting square 150mm size of PTMT with waste hole (Minum weight 100 gms) complete all as specified and directed.

S&F, Towel Rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minium weight 190 gms) complete all as specified and directed.

S&F, urinal spreader of PTMT any colour for fixing with 15mm dia pipe (Midium weight 60 gms) complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F, 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including stack 'Z' clamp complete all as specified and directed.

S&F, 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including 'Z' clamp complete all as specified and directed.

S&F, 110mm bore PVC (SWR) bend, any radius complete all as specified and directed.

S&F PVC (SWR) bends of any radius with oval and access door of 110mm dia complete all as specified and directed.

S&F, 75mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed.

S&F 110mm bore PVC (SWR) Tee equal or unequal any radius with access door complete all as specified and directed.

S&F, 75mm PVC (SWR) vent cowl complete all as specified and directed.

S&F, 110mm PVC (SWR) vent cowl complete all as specified and directed.

S&F in repairs, 125/110mm bore PVC (SWR) 'P' trap complete all as specified and directed.

S&F, 110mm PVC (SWR) WC connector bent type complete all as specified and directed.

S&F PVC (SWR) nahani trap, with chromium plated grating including jointing with solvent cement, dia of outlet 75mm complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete fixed all as specified.

M&L for PCC 1:3:6 type C2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore.

M&L 150 mm dia Salt Glazed stone ware drain pipes laid in trenches and jointed as specified.

S&F, in repair, vitreous china wash down water closet pan (pedestal pattern), white (excluding flushing cistern) including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. including seat cover in same colour etc. complete all as specified and directed.

S&F, vitreous china squatting pan, 'Orissa’ pattern, white of size 580mm x 440mm with integral foot rest, (excluding flushing cistern and flush pipe) including trap & connection to trap and to flushing pipe, anti-syphonage pipe etc. complete all as specified and directed.

S&F in repair vitreous China squatting pan 'Orissa pattern' size 580x440 mm, white with integral foot rest including 'P' or 'S' trap front or back inlet excluding flushing cistern and flush pipe including connection to trap and flushing pipe etc and making good to floor complete all as specified and directed.

S&F, in repairs, Two way bib taps cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down screwed for iron pipe or brass ferrule for 15mm bore of pipe complete all as specified and directed.

S&F, in repair vitreous china counter top wash basin oval shape, size 550 x 400mm including PVC waste coupling fixed complete all as specified and directed.

S&F, chromium plated brass peg set of six fixed with brass screw and wooden/plastic cleats.

S&F, in repairs, vitreous china urinal, Half stall type, white (excluding flushing pipe) incl providing and fixing plug, bedding urinal against wall in CM (1:2), securing urinal to plugs with and incl 60mm long brass screws, pointing around urinal back in cement, fixing flush pipe, gratings and union for discharge pipe incl supply and fixing of 32mm bore 60mm long discharge pipe complete all as specified and directed.

S&F vitreous china bowl urinal flat back, of size 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

S&F, 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white with inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed.

S&F, in repair, 10 litres capacity, valveless, syphonic action type, flushing cistern, including 32mm dia PVC flush pipe complete all as specified and directed.

S&F, flush pipe of polyethylene of low or high density or PVC 32mm dia for low leel cistern complete all as specified and directed.

S&F, in repair Toilet paper holder with flat recessed type stainless steel complete all as specified and directed

S&F, in repair, vitreous china wash basin, angle back, size 600x480mm white, excluding taps, waste, chain and plug and orcelain stopper but including brackets complete all as specified and directed.

S&F, Soap dish, approximate size 160 x 160 x 90mm, fixed with screws complete all as specified and directed.

S&F, Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all as specified and directed.

Supply only bituminous primer complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc. 15cm thickness (below or above ground level) all as specified and directed.

M&L for demolition of concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of reinforced cement concrete in any position not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (Reinforced)(reinforcement cut as required to facilitate demolition) of roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similir suspended work & water tanks for portions ordered to be dismantled and removing from site complete all as specified and directed.

Dismantling structural steel work including door , gatesbut excluding framed truss etc complete all as specified and directed.

Dismantling framed trusses n. exc.10m span complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semi corrugated, etc) sheet in roof covering

Dismantling wall and ceiling boards, partitions of any description or in any position (fibre, pulp, insulation etc.) any thickness, or insulation boards/ slabs/ blankets of any thickness including cover fillets complete all as specified and directed.

Dismantling of cast iron, PVC or reinforced concrete drain pipes jointed in cement mortar for 110mm and 75mm bore of pipe from wall/floors etc complete all as specified and directed.

Taking down carefully copper/aluminum point wiring (light, fan,socket or power) complete,including fixture and fitting such as as switches, ceiling roses, pendants, regulators, sockets,etc excluing light fittings etc,removing materials to store for keeping in safe custudy or for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surface of walls, ceiling, floor etc to match with the existing surface complete all as specified and directed.

M&L for point wiring for one light/fan/bell point controlled by one switch one way in & including PVC conduit concealed in brick or stone wall using FRLS PVC unsheathed multistrand copper conductor wire 1.5 sqmm single core for one light/fan point controlled by one switch including modular white cover plate with frame of suitable modules over modular metal flush box concealed type for earth continuity insulated PVC unsheathed (green colour) 1.5 sqmm copper earth wire connected to common earth dolly using complete all as specified and directed by Engr-in-charge. Note : (a) wiring shall be done by using proper colour coding.

M&L for point wiring for one 3pin, 5 Amps socket outlet in independent board in & including PVC conduit concealed in brick or stone wall using FRLS PVC unsheathed multistrand copper conductor wire 1.5 sqmm single core for one light/fan point controlled by one switch including modular white cover plate with frame of suitable modules over modular metal flush box concealed type for earth continuity insulated PVC unsheathed (green colour) 1.5 sqmm copper earth wire connected to common earth dolly using complete all as specified and directed by Engr-in-charge for 6 Amp socket outlet on same board complete all as specified.

M&L for point wiring for one light/fan/bell point controlled by one 3 pin, 5 Amps socket outlet on the same board controlled by another switch in & including PVC conduit concealed in brick or stone wall using FRLS PVC unsheathed multistrand copper conductor wire 1.5 sqmm single core for one light/fan point controlled by one switch including modular white cover plate with frame of suitable modules over modular metal flush box concealed type for earth continuity insulated PVC unsheathed (green colour) 1.5 sqmm copper earth wire connected to common earth dolly using complete all as specified and directed by Engr-in-charge for 6 Amp socket outlet on independent board complete all as specified.

M&L for point wiring for one light/fan/bell point controlled by one switch one way in & including PVC conduit concealed in brick or stone wall using FRLS PVC unsheathed multistrand copper conductor wire 2.5 sqmm single core for one light/fan point controlled by one switch including modular white cover plate with frame of suitable modules over modular metal flush box concealed type for earth continuity insulated PVC unsheathed (green colour) 2.5 sqmm copper earth wire connected to common earth dolly using complete all as specified and directed by Engr-in-charge for for 6/16 Amp independent socket.

M&L for poing wiring with and including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in and including medium grade PVC casing and capping double lock type 25mm in size, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. for one 3 pin, 15 Amps socket outlet point on independent board complete all as specified and directed.

S&F, in repair, lamp holder insulated body with back plate for battern fittings complete all as specified and directed.

S&F Switch piano, flush type 5 Amps One Way 230 volts complete all as specified.

S&F Switch one way 15 Amps flush type 230 volts complete all as specified.

S&F modular switch piano, flush type 6 Amps one way 230 volts complete all as specified.

S&F modular switch one way 16 Amps flush type 230 volts complete all as specified.

S&F modular socket outlet 2-3 pin 6 & 16 Amps flush type 230 volts complete all as specified.

S&F, modular fan step type regulator, suitable for 1200mm/1400mm sweep ceiling fan, 2 module complete all as specified and directed.

S&F Socket outlet 2-in-1 3 pin 6 & 16 Amps flush type 230 volts complete all as specified.

S&F, socket outlet 2 in 1, 3 pin, 5 Amps, flush type complete all as specified and directed.

S&F, in repair, socket outlet 3 pin, 6 Amps, flush type complete all as specified and directed.

S&F Socket outlet 3 pin 10 Amps flush type 230 volts complete all as specified.

S&F Ceiling rose 3 terminal size 50x65mm surface type 230 volts complete all as specified.

S&F earth continuity GI strip of size 32 x 6mm fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe complete all as specified and directed.

Supplying & laying, XLPE insulated PVC inner sheathed, 6 Sqmm, 2 core, armoured with galvanised steel strip or wire heavy duty underground cable with aluminium multi stranded conductor, 1100 volt grade, laid in trenches/duct, passing through pipe/duct or fixed on pole and connecting and testing complete all as specified and directed.

Supplying & laying, XLPE insulated, PVC inner sheathed, armored with galvanized steel strip or wire heavy duty underground cable with aluminium multi stranded conductor, 1100 volt grade of size 25 Sqmm 4 core, laid in trenches/duct, passing through pipe/duct or fixed on pole and connecting and testing complete all as specified and directed.

S&F, LED light fitting, batten type, housed in extruded from powder coated aluminium, 20 watt for soft diffuser lighting with and including lamp and connecting up complete with white PVC insulated and PVC sheathed round flexible three core copper conductor cable of suitable size and testing on completion all as specified and directed. Make: Havell / wipro/ Bajaj/ Crompton

S&F, LED Mirror light fitting, housed in extruded from powder coated aluminium, 10 watt for soft diffuser lighting with and including lamp and connecting up complete with white PVC insulated and PVC sheathed round flexible three core copper conductor cable of suitable size and testing on completion as specified and directed.

S&F LED Adore Lamp 9W, B22 base 6500K CDL type complete all as directed by Engr-In-charge. Make: Havells/Crompton/Bajaj

Labour only for cutting opening through brick walls for fixing of exhaust fan, including providing fixing and removing shoring cleaning and stacking bricks, removing surplus serviceable bricks, hard core etc. rubbish not exc 50m. forming jambs etc. to opening for 250mm exhaust fan including cutting tin wall for cement mortar 1:6 toothing and properly bonding into old work, also facing, jointing and pointing to match the existing work complete all as specified and directed

Taking down ceiling fan of any sweep of any make by disconnecting electric connection from ceiling rose, carrying out necessary repair such as rewinding of motor, replacement of condensers of 2.5 MFD, rubber bushes, bearing, flexible twin core copper cable of suitable size including overhauling by carrying out repair such as applying grease to metal parts and replacement of suitable size of cotter/split pin as required including spray painting with white synthetic enameled paint after preparation of old surface of th ceiling fan and re-fixing in its original position, commissioning, testing complete all as directed by the Engineer-in-Charge. Note : Spares replace shall not be measured and paid seperately.

S&F 30W New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 for bldg security light with GI pipe bracket of suitable size for fitting complete all as specified and directed by Engineer-in-charge. Make : Havells/Bajaj/Philips/Crompton

Taking down carefully old unserviceable main switches/ Distribution board any type including fuses MCB etc after removing all connection, wires and making good the disturb surface complete all as directed by Engineer-in-charge.

S&F, in repair, Distribution Board Power line VTPN , 4 way, 415 volts, factory made powder coated, double door with neutral and earth link, including with 3 pole MCCB 63 Amps rating, 25KA breaking capacity for incoming supply and 12 Nos single pole MCBs 6-32 Amt for out going supply complete all as specified and directed.

Taking down carefully old UNSV submain wiring of any type/any size removing material to store for keeping in safe custody or for taking credits and making good the disturbed surfaces of walls, floors, etc complete all as specified and directed.

S&F security light luminaries 35 watt with wall mounting bracket of suitable size and clamps, nut bolts etc.having pressure die cast housing with epoxy power coated dark graphite grey colour finish,prismatic polycarbonate cover with individual LED lenses-IP65 prewired Conforming to Crompton of equivalent make of wipro/Havells/Bajaj/ wipro.

S&F, LED compact fitting/batten for single LED tube of 1x20W, 220 V AC decorative box type 4 ft with integral LED driver including 20W, T8 tube rod connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed as pe Make of havells cat No. LHFXCENNTN1W020 for batten and cat no. LHLDEFXD5L8R020 for holder or equivalent make as approved by GE.

S&F, LED flat panel of size 2' x 2' luminaire of 34 watt, environmental friendly, new generation, aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source, suitable for Armstrong/Grid Ceiling complete all as specified and directed as per Make of Havells cat No. PLUTONEO2X2PLR34WLED840S or equivalent make as approved by GE.

M&L for pipe chemical earthing with GI Pipe electrode 2.25m long having outer pipe nominal dia 80mm & inner pipe noinal dia 50mm duly filled with highly conductive and anti corrosive compound of requried quantity having chemical composition Betonite 40%, Copper sulphate 20%, Gypsum 5%, Graphite 10%, Alum 5% Zine sulphate 10%, Aluminium sulphate 10% burried in ground by digging a bore of 150mm dia surrounded by soil freindly backfill compound non soluble in water including connection with and including GI strip 32 x 6mm upto 7.5m PCC pit with RCC cover etc. complete and testing on completion complete all as specified and directed. Note : Rate quoted by tenderers shall be deemed to include for following provisions:-[i] Excavation & earth work in any type of soil including removing of surplus material upto 50m[ii] PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50 x 50 cm with 8mm TMT bars " 10cm C/C both ways with handles. [iii] GI protection pipe of size 40mm bore light grade 7.5m and testing on completion complete all as specified and directed.

S&F metal plug and socket double pole with MCB SP of 20 Amps, 230 V, 10 KA all as specified and as directed by Engineer-in-charge.

S&F Sheet metal enclosure double door for DB's SPN 8 way 240 V having 200 A rated bus bar complete all as specified and directed by Engr-Incharge.

Supply and fix of exhaust fan, 230 mm sweep, 1400 rpm, MS body heavy duty, AC single phase, 230 volts with, blades, and frame and louvers including connection with 0.5 sqmm multistranded copper conductor flexible wire from ceiling rose, necessary fixing arrangement i.e anchor nut, bolt, washer, grouting and making good to disturbed surface complete all as specified and as directed. Make : Crompton/Havells/Khaitan/Almonard/Bajaj

Supply and fix of exhaust fan, 300 mm sweep, PVC body, AC single phase, 230 volts with, alongwith louvers and blades including connection with 0.5 sqmm multistranded copper conductor flexible wire from ceiling rose, necessary fixing arrangement i.e anchor nut, bolt, washer, grouting and making good to disturbed surface complete all as specified and as directed. Make : Crompton/Havells/Khaitan/Almonard/Bajaj

Supply and fix of exhaust fan, 380 mm sweep, 1400 rpm, MS body heavy duty, AC single phase, 230 volts with, blades, and frame and louvers including connection with 0.5 sqmm multistranded copper conductor flexible wire from ceiling rose, necessary fixing arrangement i.e anchor nut, bolt, washer, grouting and making good to disturbed surface complete all as specified and as directed. Make : Crompton/Havells/Khaitan/Almonard/Bajaj

M&L for Sub main wiring complete with FRLS PVC insulated unsheathed stranded copper conductor wire 4.0 Sq mm 02 runs (for Phase & Neutal) along with earth wire FRLS PVC insulated unsheathed stranded copper conductor wire of size 4.0 sq mm wire drawn through in & including PVC casing caping complete all as directed by Engr-In-charge. Note: (i). 2 run of main conductor and one run of earth conductor shall be measured as one length.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated, 230Volts, single phase, 50 Hz AC, energy saving high density PUF insulation complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and directed.

S&F MCB SPN 32A, 240 V -10 KA all as specified and as directed by Engineer-in-charge.

S&F MCB SP 6-32A, 240 V -10 KA all as specified and as directed by Engineer-in-charge.

M&L for earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth Lead 4 mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I connected to earth test point using earth strip of 25x4mm as earth lead all as specified and testing on completion including provision of earth lead protected by 20 mm dia light grade GI pipe & watering pipe shall be 15 mm bore medium grade GI pipe including all excavation and earth work in any type of soil, PCC pit with RCC cover, char coal, salt, funnel etc complete. Note : Rate quoted by tenderers shall be deemed to include for following provisions:-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 M.[ii]. PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing lead from earth electrode to test point upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 15 mm bore [ISI marked] medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 20 mm bore light grade 7.5m.

Bhumi Construction

ALPINE CONSTRUCTIONS

Shree Builders

Shivaang Enterprise

Ramdev and Sons

M.A. MUNSHI AND CO.

Marudhar construction company

Bidder Name

Singh Engineer And Contractor