Augmentation of LWSS Jablyana under JJM in Tehsil Ghumarwin Distt. Bilaspur (HP)(SHProviding and installation of centrifugal pumping machinery with allied accessories in 2nd phase 1st stage).

Amount

Providing / Installation horizontal spindle horizontal split casing/end suctions (backpull out arrangement) single/double/ multistages centrifugal pump or combination of energy saver pump in series/parrallel of recommended make such as Mather & Platt / KSB/ Kirloskar make as per BIS: 1520-1980 with upto date ammendments, read with IS: 9137-1978 or latest edition suitable for lifting clear water for under mentioned characterstics with bronze impellers/priming funnels, casing ring and shaft sleaves of bronze, shaft of steel grade EN-8 with cast iron casing coupled directly through a flexible coupling on a MS/Cast steel base plate ( base plate to be from the manufacturers of the pumping unit only) to Squarrel cage/ slippering drip proof induction motor of standard make such as Kirloskar/BHEL/Crompton/ABB/NGEF/Siemens/Jyoti / Marathan make and suitable for operation on 400 (+)/-) 10% volts, 50 cycles/second, 3 phase AC electric supply. The power of electric motor should be atleast 10% in excess of the maximum power required by the pump in the operation range of (+) 10% and (-) 15% of the duty point head. The motor should be as per IS: 325-1978 with upto date ammendments read with IS: 900-1972. It should include cost of bearing nuts, bolts and pointing etc. and should meet the following requirements:- Discharge (Q) LPS or 3.12 Cum/Hr. Total Dynamic Head: 297.90 Meters. LWL in sump well (h). 799.00 Meters. Pump Shaft level: 796.10 Meters. Level at discharge point. 1037.75 Meters. Suction lift. 2.90 Meters. Residual head: 30.00 Meters. Static Head. 241.650 Meters. Rising main. Length. 1785.00 Meters. Dia. 65 mm Pumping Hours. 8 Hours. Altitude of Installation above MSL 750 Meters Characteristics of water. (a) Temperature 20o C (b) Abient Temp. 42oC (c) Turbidity Clear water (<than 50JTU (d) Alkalanity. Mg/Ca Co3 (e) Size of the solids. Mm (f) Other. (Please see specifications, terms and conditions in the SOQ PDF file attached)

Supplying, fixing, testing and successfully commissioning of floor mounted soft starter suitable for the puming machinery offered at Sr. NO.1 of either of Crompton Greaves /Siemens/ L&T/ABB/Allen Bradley duly certified by CE/UL/CAS suitable for motor operating in 200-480 VAC3 phase Ambient temperature 250 to 600 cel. Ramp ultimate -20 second, inbuilt by pass system duly certified by CE/UL/CSA fully programmeable including panel board with accessories and MCCB of reputed make with Amp meter, voltameter, push button and single phase preventor complete. All digital display connected with motor etc. and all other connections needed to make the motor pump run successfully in all respect as per direction of Engineer-in-charge. The equipment supplied should be compatibility upgradable for use in future automization of the scheme with below mentioned technical spacification of soft panel / soft starter providing and fixing in position at site. These accessories complete in all respect in all leads and lifts and carriage of materials.(Please see specifications, terms and conditions in the SOQ PDF file attached)

Capacitor of Crompton/GEC/Bajaj/Havels/Assian/L&T make as per IS: 3824-1986 with upto date amendments to raise the power factor at site to 0.95 for direct connectons to induction motor individually of reqired 7 KVAR rating (Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing cast iron flanged/screwed type foot valve with strainer as per IS: 4038-1986 with upto date ammendments of Kirloskar/Leader make 100 mm dia class PN-1.(Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing double flanged cast iron sluice valve of Leader/Kirloskar make of 80 mm dia for the suction pipe and capable of withstanding the normal seat pressure as per IS: 780-1984 with upto date ammendments.(Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing double flanged cast steel sluice valve of Leader/Kirloskar/Gled make and of 65 mm dia for the delivery line of the pump and capable of with standing the normal seat pressure and as per IS:1414 API-600, class ASA-300 with upto date ammendments.(Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing double flanged (Swing type) cast steel reflux valve of Leader/Kirloskar/Gled make and of 65 mm dia having bye pass arrangement on the delivery line of pump and capable of with standing normal seat pressure as per BIS 5312-1984 (part-1)/BS: 1868-API-600 with upto date ammendments class ASA-300.(Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing double flanged( Swing type) cast steel non return valve of Leader/ Kirloskar/Gled make and of 65 mm dia having bye pass arrangement for rising main and capable of with standing normal seat pressure as per BIS 5312-1984 (part-1)/BS 1868 API-600 class ASA-300 upto date ammendments ( 52 Kg/cm2).(Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing 100mm dia circular dial pressure gauge of Fiebig / Bourden make complete with all accessories such as stop cock, copper tubing etc. as per IS: 3624-1987 with upto date ammendments range 0-52 Kg/cm2 (Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing discharge meter of standard make to be fixed on rising main near the storage tank as per the direction of the Engineer-in-Charge as per IS: 2373-1981 with upto date ammendments. Suitable for 13.45 LPS discharge.

Installation of all the items appearing at Serial No. 1 to 9 as per the systematic drawing attached with the tender documents ( Drg.No.1)

Providing and fixing double flanged MS/GI piping work layout to be approved by the Engineer-in-Charge for suction and delivery pipes suitable to pump(s) offered and common header as per the rising main respectively complete with all specials such as bends ,tees reducers/ increasers with companion flanges matching with the relevant specifications of the accessories as indicated in the drawing No.2 including rubber/asbestos gasket of minimum 3mm thickness as per IS 2712-1979 and required number of nuts and volts as per IS: 1364-1983. The pipes shall be as per relevant IS Code and to withstand 1.5 times total head stipulated under item No.1. (Please see specifications, terms and conditions in the SOQ PDF file attached)

The size of the various components to be as under:-

(i) Suction pipe 80mm dia Min.length = 15 mtr.

(ii) Delivery pipe 65mm dia -do- = 5 mtr.

(iii)Common Header 80mm dia -do- = 10 mtr.

and will extended upto 5 meters from the outer wall of the pump house in the direction to be jointed.

Providing and laying copper PVC insulated armoured power cable ( one cable carrying all the three phases) of suitable size and capacity to and all other electrical equipments as per IS: 1554 (P-I)1988 or latest with upto date ammendments of Siemens/ IEC/ICC/GICO/Grandly/National make including all other accessories such as thimbles, flexible, pipes solder, nuts and bolts, cable glands etc. laid in pipes or trenches under floor. (Please see specifications, terms and conditions in the SOQ PDF file attached)

Motor side: 6.00 mm2 Min length = 20 mtrs.

Supply side: 10.00 mm2 Min. length =10 mtrs.

Providing and fixing double loop earthing and copper plate 600mmx600mmx3mm thick electrode complete with material such as thimbles, nuts and bolts, charcoal and common salt, 25mmx6mm copper strips/ as per IS: 3043-1987 with upto date ammendments for motors and other electrical eqipments and digging of pits etc. complete in all respect.

3rd phase 1st stage

Providing / Installation horizontal spindle horizontal split casing/end suctions (backpull out arrangement) single/double/ multistages centrifugal pump or combination of energy saver pump in series/parrallel of recommended make such as Mather & Platt / KSB/ Kirloskar make as per BIS: 1520-1980 with upto date ammendments, read with IS: 9137-1978 or latest edition suitable for lifting clear water for under mentioned characterstics with bronze impellers/priming funnels, casing ring and shaft sleaves of bronze, shaft of steel grade EN-8 with cast iron casing coupled directly through a flexible coupling on a MS/Cast steel base plate ( base plate to be from the manufacturers of the pumping unit only) to Squarrel cage/ slippering drip proof induction motor of standard make such as Kirloskar/BHEL/Crompton/ABB/NGEF/Siemens/Jyoti / Marathan make and suitable for operation on 400 (+)/-) 10% volts, 50 cycles/second, 3 phase AC electric supply. The power of electric motor should be atleast 10% in excess of the maximum power required by the pump in the operation range of (+) 10% and (-) 15% of the duty point head. The motor should be as per IS: 325-1978 with upto date ammendments read with IS: 900-1972. It should include cost of bearing nuts, bolts and pointing etc. and should meet the following requirements:- Discharge (Q) LPS or 4.76 LPS Cum/Hr. Total Dynamic Head: 375.13 Meters. LWL in sump well (h). 705.00 Meters. Pump Shaft level: 702.20 Meters. Level at discharge point. 1040.70 Meters. Suction lift. 2.90 Meters. Residual head: 3.00 Meters. Static Head. 335.70 Meters. Rising main. Length. 1485.00 Meters. Dia. 80 mm Pumping Hours. 8 Hours. Altitude of Installation above MSL 750 Meters Characteristics of water. (a) Temperature 20o C (b) Abient Temp. 42oC (c) Turbidity Clear water NTU (d) Alkalanity. Mg/Ca Co3 (e) Size of the solids. Mm (f) Other. (Please see specifications, terms and conditions in the SOQ PDF file attached)

Supplying, fixing, testing and successfully commissioning of floor mounted soft starter suitable for the puming machinery offered at Sr. NO.16 of either of Crompton Greaves /Siemens/ L&T/ABB/Allen Bradley duly certified by CE/UL/CAS suitable for motor operating in 200-480 VAC3 phase Ambient temperature 250 to 600 cel. Ramp ultimate -20 second, inbuilt by pass system duly certified by CE/UL/CSA fully programmeable including panel board with accessories and MCCB of reputed make with Amp meter, voltameter, push button and single phase preventor complete. All digital display connected with motor etc. and all other connections needed to make the motor pump run successfully in all respect as per direction of Engineer-in-charge. The equipment supplied should be compatibility upgradable for use in future automization of the scheme with below mentioned technical spacification of soft panel / soft starter providing and fixing in position at site. These accessories complete in all respect in all leads and lifts and carriage of materials.

Capacitor of Crompton/GEC/Bajaj/Havels/Assian/L&T make as per IS: 3824-1986 with upto date amendments to raise the power factor at site to 0.95 for direct connectons to induction motor individually of reqired 7 KVAR rating (Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing cast iron flanged/screwed type foot valve with strainer as per IS: 4038-1986 with upto date ammendments of Kirloskar/Leader make 100 mm dia class PN-1. (Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing double flanged cast iron sluice valve of Leader/Kirloskar make of 100 mm dia for the suction pipe and capable of withstanding the normal seat pressure as per IS: 780-1984 with upto date ammendments.(Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing double flanged cast steel sluice valve of Leader/Kirloskar/Gled make and of 80 mm dia for the delivery line of the pump and capable of with standing the normal seat pressure and as per IS:1414 API-600, class ASA-300 with upto date ammendments.(Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing double flanged (Swing type) cast steel reflux valve of Leader/Kirloskar/Gled make and of 80 mm dia having bye pass arrangement on the delivery line of pump and capable of with standing normal seat pressure as per BIS 5312-1984 (part-1)/BS: 1868-API-600 with upto date ammendments class ASA-300.(Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing double flanged( Swing type) cast steel non return valve of Leader/ Kirloskar/Gled make and of 80 mm dia having bye pass arrangement for rising main and capable of with standing normal seat pressure as per BIS 5312-1984 (part-1)/BS 1868 API-600 class ASA-300 upto date ammendments ( 52 Kg/cm2).(Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing 100mm dia circular dial pressure gauge of Fiebig / Bourden make complete with all accessories such as stop cock, copper tubing etc. as per IS: 3624-1987 with upto date ammendments range 0-52 Kg/cm2 (Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing discharge meter of standard make to be fixed on rising main near the storage tank as per the direction of the Engineer-in-Charge as per IS: 2373-1981 with upto date ammendments. Suitable for 13.45 LPS discharge.

Installation of all the items appearing at Serial No. 1 to 9 as per the systematic drawing attached with the tender documents ( Drg.No.1)

Providing and fixing double flanged MS/GI piping work layout to be approved by the Engineer-in-Charge for suction and delivery pipes suitable to pump(s) offered and common header as per the rising main respectively complete with all specials such as bends ,tees reducers/ increasers with companion flanges matching with the relevant specifications of the accessories as indicated in the drawing No.2 including rubber/asbestos gasket of minimum 3mm thickness as per IS 2712-1979 and required number of nuts and volts as per IS: 1364-1983. The pipes shall be as per relevant IS Code and to withstand 1.5 times total head stipulated under item No.1. The size of the various components to be as under:- (i) Suction pipe 100mm dia Min.length = 15 mtr. (ii) Delivery pipe 80mm dia -do- = 5 mtr. (iii)Common Header 100mm dia -do- = 10 mtr. and will extended upto 5 meters from the outer wall of the pump house in the direction to be jointed. (Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing and laying copper PVC insulated armoured power cable ( one cable carrying all the three phases) of suitable size and capacity to and all other electrical equipments as per IS: 1554 (P-I)1988 or latest with upto date ammendments of Siemens/ IEC/ICC/GICO/Grandly/National make including all other accessories such as thimbles, flexible, pipes solder, nuts and bolts, cable glands etc. laid in pipes or trenches under floor. Motor side: 6.00 mm2 Min length = 20 mtrs. Supply side: 10.00 mm2 Min. length =10 mtrs (Please see specifications, terms and conditions in the SOQ PDF file attached)

Providing and fixing double loop earthing and copper plate 600mmx600mmx3mm thick electrode complete with material such as thimbles, nuts and bolts, charcoal and common salt, 25mmx6mm copper strips/ as per IS: 3043-1987 with upto date ammendments for motors and other electrical eqipments and digging of pits etc. complete in all respect.

MANAHOR LAL SURINDER KUMAR

Raman Thakur Govt. Cont.