Construction of new OPD building at Central Hospital Dhanbad, BCCL

Amount

EARTH WORKS : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge: All kinds of soils

Earth work in surface excavation not exceeding 30 cm in depth but exceedingl.s m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, as per directions of EnEineer in lncharge

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. : Ordinary rock

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre). : Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials: All kinds of soil: 0.00 to 1.5m

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials: All kinds of soil: 1.5 to 3.0 m

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials: All kinds of soil: 3.0 m to 4.5 m

Excavating trenches of required width for pipes, cables, etc. including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exc : All kinds of soil: Pipes, cables, etc. exceeding 80mm dia but not exceeding 300mm dia.

Extra rates for quantities of works, executed :In or under water and/or liquid mud, including pumping out water as required.(Note for item no. 2.24:- The extra percentage rate is applicable in respect of each item but limited to quantities of work executed in these difficult conditions. The unit, namely, metre depth, to be considered for payment, shall be the depth measured from the sub soil water level upto the centre of gravity of the quantity executed in difficult conditions. The depth shall be reckoned correct to 0.1 metre. 0.05 metre or more shall be taken as 0.1 metre and less than 0.05 metre ignored.)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Carriage of earth - 5 km ( by mechanical transport)

Disposal of excavated excess earth/rock away from the site including conveyance of materials up to an average lead of 5KM away from the site, and correspondiong required lift, loading, unloading etc complete as directed by the Engineer-in-charge. (The quantity is net quantity of capacity of truck after deduction of 20% for looseness)(considering the maximum disposal location at 5 KM distance) : Earth By mechanical transport including loading, unloading and stacking. (Lead up to 5KM away from the site)

Disposal of excavated excess earth/rock away from the site including conveyance of materials up to an average lead of 5KM away from the site, and correspondiong required lift, loading, unloading etc complete as directed by the Engineer-in-charge. (The quantity is net quantity of capacity of truck after deduction of 20% for looseness)(considering the maximum disposal location at 5 KM distance): Ordinary Rock By mechanical transport including loading, unloading and stacking. (Lead upto 5KM away from the site)

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m : All kinds of soil

Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material: Beyond 30 cm girth upto and including 60 cm girth

Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material: Beyond 60 cm girth upto and including 120 cm girth

Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material: Beyond 120 cm girth upto and including 240 cm girth

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment)

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Providing and stacking of Bottle palm of ht. 150,180 cm bottom girth 20 25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge.

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material's as per direction of officer in charge (excluding cast of plant & water) Hedge Plant /Ground cover

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide will be provided by the Department & lawn mover and brush cutter with fuel , other T & P material/articles shall be provided by the contractor.) : Play grounds / Public parks (as per yard stick 1Mali =2.00Acre). (Rate to be quoted in sqm/year)

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) :

Fine dressing of the ground

Providing and Displaying Bamboo Buddha Valley with fresh & healthy 5 to 6 suckers 1.80 m to 2.10m ht umbrella type well developed in 50 cm Cement Pot as per direction of the officer-in-charge

Providing and displaying of Areca palm having ht. 1.50 m to 1.80 m with 6 to 8 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Croton Golden specimen having ht. 90 cm to 1.05 cm with 5 to 6 branches, well developed, fresh and healthy foliage in 30 cm size of Earthen pot/Plastic pot as per direction of the officer-in-charge.

Providing and Displaying Kochia well developed fresh & healthy 20 to 25 cm ht. lush green well shaped in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and stacking Jasmine grandiflorum (chameli) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. .

Providing and stacking of Wedelia trilobata, full of leaves in 15 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Cestrum nocturnum (Raat ki Rani) of height 60- 75 cm. with 4-5 branches in bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Plumeria acutifolia of height 120-135 cm. with 2-3 branches in HDPE bag of size 30 cm as per direction of the officer-in-charge.

Anti termite treatment (Note : Warranty for 05 Years to be provided by Contractor. The work can only be carried out by the licensed applicator approved by appropriate authority) : Supplying chemical emulsion in sealed containers including delivery as specified : Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

CONCRETE WORKS : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3.6 (1 Cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) In PLINTH

1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:1½:3 (1 cement : 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Extra for laying concrete in or under water and/or liquid mud including cum per cost of pumping or bailing out water and removing slush etc.complete.Note for item No. 4.15 :- The quantity will be calculated by multiplying the depth measured from the sub-soil water level up to centre of gravity of concrete under sub-soil water level with quantity of concrete in cum executed under sub-soil water. The depth of centre of gravity shall be reckoned correct to 0.1m. 0.05m or more shall be taken as 0.1m and less than 0.05m ignored.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

REINFORCED CEMENT CONCRETE WORK : Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete.

Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting, propping etc. and removal of form for : Shelves (Cast in situ)

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts.

Centering and shuttering including strutting, propping etc. and removal of form for : Stairs, (excluding landings) except spiral-staircases

Centering and shuttering including strutting, propping etc. and removal of form for : Small lintels not exceeding 1.5m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like.

Centering and shuttering including strutting, propping etc. and removal of form for : Edges of slabs and breaks in floors and walls : Under 20 cm wide

Centering and shuttering including strutting, propping etc. and removal of form for : Weather shade, Chajjas, corbels etc., including edges.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).: Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level: Thermo-Mechanically Treated bars of grade Fe-500D or more. (SAIL/TISCO/RINL or Any others primary Steel Producer having Integrated Steel Plant (ISP) and using iron ore as the basic raw material and having In – house iron rolling facilities , followed by production of steel through the process of DRI- EAF , BF-BOF and Corex – BOF only)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level: Thermo-Mechanically Treated bars of grade Fe-500D or more. (SAIL/TISCO/RINL or Any others primary Steel Producer having Integrated Steel Plant (ISP) and using iron ore as the basic raw material and having In – house iron rolling facilities , followed by production of steel through the process of DRI- EAF , BF-BOF and Corex – BOF only)

Extra for laying reinforced cement concrete in or under water and/ or liquid mud, including cost of pumping or bailing out water and removing slush etc., complete. Note For Item No. 5.31:- The quantity will be calculated by multiplying the depth measured from the subsoil water level up to the centre of gravity of the R.C.C. under subsoil water with the quantity of R.C.C. in cubic metre executed under subsoil water. The depth of centre of gravity shall be reckoned correct to 0.1 m. 0.05 m or more shall be taken as 0.1 m and less than 0.05 m ignored. No extra payment shall be made for placing reinforcement or centering & shuttering under sub - soil water conditions.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement: All works upto plinth level: Concrete of M25 grade with minimum cement content of 330 kg /cum. (Note : Mix design to be submitted by contractor to BCCL for Approval- No extra to be paid on this account)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement:All works above plinth level upto floor V level: Concrete of M25 grade with minimum cement content of 330 kg /cum (Note : Mix design to be submitted by contractor to BCCL for Approval- No extra to be paid on this account)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement -All work up to plinth level : 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). Made of G.I. wire of dia 4 mm

Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

BRICK WORK : Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : Cement mortar 1:6 (1 cement : 6 Coarse sand)

Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth and upto floor V level: Cement mortar 1 : 4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

WOOD & PVC WORK : Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made: Frame size 65 x 125 mm. (Warranty as provided by Manufacturer)

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made: Frame size 65 x 100 mm (Warranty as provided by Manufacturer)

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately): 30 mm thick (Warranty as provided by Manufacturer)

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately): 35 mm thick (Warranty as provided by Manufacturer)

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) : 35 mm thick (Warranty as provided by Manufacturer)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete: 250x10 mm

Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge: 200 mm

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : 125x64x1 .90 mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge (Door handle, lock and stopper etc. to be paid separately) (Make - DORMA/MODI FLOAT GLASS, ASAHI GALSS, SAINT GOBAIN or equivalent)

Providing & fixing 12mm thick clear toughened glass fixed in Windows . The rate is inclusive of providing of 3M film as per approved pattern/ Design on the glass, cost of materials and labour charges etc. complete as per design and partitions to be fixed with SS finished patch fittings on top, bottom with all necessary hardware complete as per direction of Engineer-in-charge: (Make - DORMA/MODI FLOAT GLASS/ ASAHI GALSS/SAINT GOBAIN or equivalent)

Providing and fixing Stainless steel 304 Grade H- type pull handle of size min 32 mm dia and 1200mm long of approved make including SS screws, including making holes of required size in shutter etc. complete as per direction of Engineer-in-Charge.

Providing and fixing SS Bottom patch Lock with cylinder of approved make including necessary screws etc. all complete.

Providing and fixing SS floor mounted half dome door stopper of dia 45mm including necessary screws etc. all complete.

LAQUER GLASS PANELLING: Providing & Fixing of lacquer glass as per approval in any color fixed on existing ply/ MDF base with all other acessories as per architectural drawing. The Lacquered glass shall be highly durable, humid resistance, polyurethane lacquer glass. The glass to be manufactured by industrial curtain coating process. It should meet quality standards as per BS EN 1036 1999 & conform to persoz hardness test of at least 220 oscillations. The substrate of the glass should confirm to Standard BS EN 572 1995 parts 1 & 2. Lacquered glass to be manufactured to tight specifications, relating to consistency of color, opacity and homogeneity throughout production campaigns and also to the ageing properties, mechanical resistance, and resistance to humidity and to chemical agents of the lacquer. The color of the lacquer should remain stable when exposed to normal levels of ultra-violet light in interior applications, as per direction of Engineer-in-charge:

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge: 10 x 60 mm

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1 .6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.: GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation and backed with a black Glass fiber acoustical fleece.

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on inter-locking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6 mm reveal profile (white/ black),comprising of main-T runners of size 15x42 mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary ntermediate cross-T of size 15x42 mm of length 600 mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge: With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles

Providing and fixing brass curtain rods of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 25 mm diameter.

Providing and fixing approved brand and manufacture of Rack and pinion door closer TS 68 EN size 2/3/4, with std. arm and with two independent closing valves and latching speed adjustable by arm. Silver finish. As per EN 1154. with all necessary accessories and screws etc. complete in all respects as per manufacture specificatios & as directed by Engineer-in-charge. Make : dormakaba / Hafele / GEZE or equivalent.

Providing and fixing approved brand and manufacture of Pure 8100 Type 3 Package with Pair of Pure 8100 Design Lever Handle on Roses & escutcheons. Including 271a Sash lock with 72mm CTC, 55mm Backset 20mm Square forend. EPC 60mm length oneside thumb turn otherside coin release operation with all necessary accessories and screws etc. complete in all respects as per manufacture ofrs' specificatios & as directed by Engineer-in-charge. Make : dormakaba / Hafele / GEZE or equivalent.

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

STEEL WORK : Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Structural steel work in single section, fixed with or without connecting plate. including cutting, hoistin& fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer Using M.S. angels 40x40x6 mm for diagonal braces

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required : In stringers, treads, landings etc. of stair cases including use of chequered plate wherever required, all complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required: In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes. channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of EnBineer-in- cha.ge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing concertina coil fencing with punched tapeconcertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apartand with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

FLOORING WORK : Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Double charge vitrified tile polished finish of size : Size of Tile 800 x 1200 mm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete: Size of Tile 800x800 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily: Glazed Vitrified tiles Matt/Antiskid finish of size : Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily: Glazed Vitrified tiles Matt/Antiskid finish of size : Size of Tile 800 x 1200 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge: Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.: Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge : Granite work

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels: Area of slab upto 0.50 sqm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels: Area of slab over 0.50 sqm

Extra for fixing marble / granite stone over and above corresponding basic item, in facia and drops of width upto 150mm with epoxy resin baesd adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/Stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edge etc. complete.

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete: Granite of any colour and shade

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade.

Providing and fixing machine cut, mirror / eggshell polished , Granite stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 oarse sand) laid and jointed with white cement slurry @ 3.3 kg/Sq.Mt. including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge. a. 18 mm thick Granite stone slab any colour etc.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, properdrainage of water to make it watertight including checking of all the structural and functional design.

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles,including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Light shade pigment using white cement.

Extra for pre finished nosing to treads of steps of marble stone.

Extra for marble stone flooring in treads of steps and risers using single length up to 2.00 metre.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.: 40mm thick with 20mm nominal size stone aggregate.

Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge:

ROOFING : Providing and laying gola 75x75mm in cement concrete M15 grade including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design in 75x75 mm deep chase.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised Rigid PVC RAIN WATER PIPES conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes: 110 mm diaMeter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: Coupler : 110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: Bend 87.5° : 110 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: Shoe (Plain) : 110 mm Shoe

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: Single tee with door: 110X110X110

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete: 110 mm

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

FINISHING WORK : 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)

12 mm cement plaster of mix 1:6 (1 cement: 6 fine sand)

12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand)

12 mm cement plaster finished with a floating coat of neat cement of mix 1:4 (1 cement: 4 fine sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Add or deduct for plaster drip course/ groove in or moulding to R.C.C. projections.plastered surface

6 mm cement plaster of mix : 1:3 (1 cement: 3 fine sand)

Neat cement punning.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part hereof: 10 to 13m

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats. (Anti bacterial Paints as approved by EIC)

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre (Anti bacterial Paints as approved by EIC)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.Two or more coats on new work (Anti bacterial Paints as approved by EIC)

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: 13.47.1 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Finishing walls with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work.

Providing and fixing GI hexagonal chicken wire mesh of size 12mm x22g at the junction of disimilar surfaces of brick masonry wall and R C C column by beams and the like including necessary nails for fixing etc, complete all as per specification and direction of Engineer -in -charge for all floor at all heights.

Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer-in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/ moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately. (Warranty as provided by Manufacturer)

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia, 50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. : This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/ tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre) roll and two coats of primer suitable for panelling as per manufacturer’s specification as per direction of Engineer-in-Charge all complete.

ALUMINIUM/UPVC WORK : Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable: Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body : Using R2 series with frame (70 mm & above) x (40 mm & above) & both glazed and fly screen sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre).

Providing and fixing glazing in aluminium/upvc door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)

Filling the gap in between aluminium frame/upvc frame and adjacent RCC/Brickwork/ Stone Work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge: Upto 5mm depth and 5mm width

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete: Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides

Providing and fixing steel (white power coated) crescent lock for uPVC / aluminium sliding window/ door with necessary screws etc. complete.

Providing and fixing steel roller for uPVC/aluminium sliding windows with necessary screws etc. complete.

WATER PROOFING (Note All Water Proofing work to be warranted for 10 Years unless specified in item) : Grading roof for water proofing treatment with.Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete : Serrated with central bulb (225 mm wide, 8-11 mm thick)

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 3 mm thick. (Warranty -10 Years)

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

Providing and mixing integral crystalline admixture for water proofing treatment to RCC structures like basement raft, retaining walls, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc. at the time of transporting of concrete into the drum of the ready-mix truck , using integral crystalline admixture @0.80% (minimum) to the weight of cement content per cubic meter of concrete) or higher as recommended by the manufacturer's specification in reinforced cement concrete at site of work. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 90%, compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure. The crystalline admixture shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

SITC of Primer & Providing two coats of liquid applied, solvent-free elastomeric waterproofing membrane, shall be made of hydrocarbon free polyurethane with at least 90% solid content- NITOPROOF 600PF or equivalent . with necessary surface preparation, coving, primer etc. The waterproofing membrane shall be terminated on the top of parapet walls. complete all as per specification and direction of Engineer -in -charge. The product performance shall carry guarantee for 10 years against any leakage.

Coving at all the junctions to be done for a size of 50mm X 50mm with polymer modified mortar prepared by mixing 50 kg cement + 150kg Sand + 4Litre of Nitobond SBR Latex + Water required for mortar consistency, complete all as per specification and direction of Engineer -in -charge

Separation Layer : Supply and apply 120 gsm geotextile as over waterproofing layer, complete all as per specification and direction of Engineer -in -charge

Providing and applying UV resistant Nitoseal PU 40 or equivalent on Concrete screed, concrete should be laid in panel of2 . 5 mx2.5mm thinness mediates10 mm x 6mm grooves sealed with UV resistant PU sealant Nitoseal PU40 or equivalent, Complete all as per manufacturer's recommendations as directed by the Engineer-in-charge.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage: For horizontal surface one coat @1.10 kg per sqm. (Warranty -05 Year)

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage: For vertical surface two coats @0.70 kg per sqm (Warranty -05 Year)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. (Warranty -05 Year)

Strcutrual Glazing & Misc : Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.................................................1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml. 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test, Tests to be conducted on site. 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml. (Detrailed specification mentioned in NIT - Please refere NIT )

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm: Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/ m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge.

Manual Roller Blinds : Supplying and installing roller blinds of approved make, model and shade at all heights and location and required width and comprising of approved shade and quality fabric, 1 mm thick anodized extruded Aluminium alloy roller tube of 38-mm O.D , a bidirectional operating Clutch mechanism designed for adjustment-free, slippage-free, crash proof smooth operation for all heights, high strength fiber glass reinforced polyester idler, powder coated steel Insert type brackets fitted with roller tube, round bottom rail, control unit engrooved with a Ball Pitch of minimum 6.5mm, Stainless Steel Ball Chain, and powder coated atomized steel installation brackets. The clutch mechanism comprises of a SS beaded chain and carbon steel spring wrapped by means of a high strength fiber glass reinforced polyester assembly to transmit motion from driving to driven members. The installation brackets shall facilitate overhead, side or face mounting with clutch assembly on either end of the roller. Idler shall consist of a centre shaft and outside sleeve which provide bearing surface for roller tube and rotate freely on centre shaft for smooth and quiet operation . Bottom rail along with the fabric shall be enclosed in a suitably created pocket and shall be of powder coated aluminium tube and closed from sides with end caps. The item includes all fittings, accessories, brackets, screws, anchor fasteners, fabric as per approved sample and shade all complete as per drawings, tender specifications, relevant standards and direction of Engineer in charge. (Height of blind from top bracket to bottom tube and width from bracket to bracket shall be measured for payment) : Manual Roller Blinds with following specification: Composition- 30% Polyester (max),70% PVC on Polyester(min), Openness factor- 3-5%(as approved) Weight (gram/ sqm)- min 440 gm/sqm , Thickness- min 0.60 mm Fire Classification- Class A( NFPA 101 or Class 1 (UNE EN 13773) or equivalent as per relevant standards and specifications , Fastness to light- 6-7/8 or higher Indoor Air Quality- GreenGuard / Eco-Codice Certified. Manufacturer's warrantee- minimum 5 years. as specified and as directed by the Engineer- in-Charge.

Providing and fixing factory made solid Foam uPVC profile for kitchen cabinet frame (45 x 20 mm) of approved shade, quality and make. The profile shall be laminated on both sides, made from rigid foam sheets (Single extruded) having density 600 Kg/cum and the exposed edges sealed with PVC edge beading of same shade and colour. The frame shall be fire retardent with necessary screw holding capacity. Frame shall be fixed to wall using Expendable Fastner with necesary stainless steel screws, all complete as per direction of Engineer-in-charge.

Providing and fixing factory made Kitchen Cabinet Shutter/Partition 20 mm nominal thickness of approved shade, quality and make, made from rigid foam sheets (Single extruded) having density 600 Kg/cum and laminated on both side by laminate Sheet/PVC foil lamination. The exposed edges shall be sealed with PVC edge beading of same shade and colour. The shutter shall be fire retardent having necessary screw holding capacity. Shutter shall be fixed to frame using approved hinges with necessary stainless steel screws, all complete as per direction of Engineer-in-charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain white color board for backing of cup boards and bathroom/kitchen cabinets etc. of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel screws etc. all as per direction of Engineer-In- Charge. (Note: stainless steel screws shall be paid separately): 12 MM THICK. (Warranty as provided Manufacturer)

Providing and fixing concealed hinge of approved quality for 19-20mm thick door with stainless steel screws complete in all respect as per direction of EIC.

Suppying Stainless steel screw : 50 mm length

Providing and fixing of façade at all heights with extruded hollow Clay / Terracotta ventilated rain screen tiles of height 250/ 300/ 400mm and length of 595 mm of approved texture, design and pattern having Flexural Strength/ Modulus of Rupture of 14 N/m2 and maximum water absorption of 10% tested as per ISO 10545-4:2004(E) and ISO 10545-3:1995 respectively in true level fixed to a supporting aluminium framework(Alloy 6063 T5/T6) consisting of vertical 'T' (for intermediates)/ 'L' (for ends/ termination)/ Tubular sections (at corners)of size 80x60x2mm/ 40x60x2mm/ 40x40x2mm respectively, spaced at maximum spacing of 600mm c/c matching to the tile vertical grid, and horizontal aluminium 'C'-clamps of size 56x25x2mm thickness of length 150mm at junction of tiles and of length 75mm at wall ends/ corners fixed on top of the vertical sections at spacing of 250/ 300/ 400mm c/c matching to the tile horizontal grid with two numbers of self- drilling / self-tapping SS screws of size 5.5x25 mm with EPDM washers. The vertical 'T'/'L/ Tubular' sections shall be fixed to the wall using HDG (hot-dip-galvanized) steel L-brackets (galvanizing thickness of minimum 80 microns)of size 110x80x6 mm at intermediate vertical aluminium profiles and of size 220x110x12 mm at outer corners and stainless steel grade 304,M10 full threaded anchor fasteners with nylon sleeve 100mm long (for brick work) and M8 expansion anchor fasteners 75mm long for concrete surface, spacing of brackets to be based on a structural/ static calculation.: With 16mm thickness (+/- 10%) terracotta tiles of other than grey colors

SIGNAGES : Providing and fixing of signages, modular curved frame technology,of various widths and lengths, to form suggested usages,made of aluminium extruded sections , duly anodised ,all signages shall be provided with 0.6-0.8mm polycarbonate protecting film over the prints, of appropriate size, Complete all as per manufacturer's recommendations as directed by the Engineer-in-charge: Room No, deratils (300 DIA)

Providing and fixing of signages, modular curved frame technology,of various widths and lengths, to form suggested usages,made of aluminium extruded sections , duly anodised ,all signages shall be provided with 0.6-0.8mm polycarbonate protecting film over the prints, of appropriate size, Complete all as per manufacturer's recommendations as directed by the Engineer-in-charge : BOTH SIDE- WALL PROJECTED LADIES TOILET (200x200)

Providing and fixing of signages, modular curved frame technology,of various widths and lengths, to form suggested usages,made of aluminium extruded sections , duly anodised ,all signages shall be provided with 0.6-0.8mm polycarbonate protecting film over the prints, of appropriate size, Complete all as per manufacturer's recommendations as directed by the Engineer-in-charge: BOTH SIDE-WALL PROJECTED GENTS TOILET (200x200)

Providing and fixing of signages, modular curved frame technology,of various widths and lengths, to form suggested usages,made of aluminium extruded sections , duly anodised ,all signages shall be provided with 0.6-0.8mm polycarbonate protecting film over the prints, of appropriate size, Complete all as per manufacturer's recommendations as directed by the Engineer-in-charge : DOOR PLATE LADIES TOILET (80x300)

Providing and fixing of signages, modular curved frame technology,of various widths and lengths, to form suggested usages,made of aluminium extruded sections , duly anodised ,all signages shall be provided with 0.6-0.8mm polycarbonate protecting film over the prints, of appropriate size, Complete all as per manufacturer's recommendations as directed by the Engineer-in-charge : DOOR PLATE GENTS TOILET (80x300)

Providing and fixing of signages, modular curved frame technology,of various widths and lengths, to form suggested usages,made of aluminium extruded sections , duly anodised ,all signages shall be provided with 0.6-0.8mm polycarbonate protecting film over the prints, of appropriate size, Complete all as per manufacturer's recommendations as directed by the Engineer-in-charge : DOOR PLATE HANDICAP TOILET (80x300)

Providing and fixing of signages, modular curved frame technology,of various widths and lengths, to form suggested usages,made of aluminium extruded sections , duly anodised ,all signages shall be provided with 0.6-0.8mm polycarbonate protecting film over the prints, of appropriate size, Complete all as per manufacturer's recommendations as directed by the Engineer-in-charge: ELECTRICAL PANEL & Others Misc (80x300)

Providing and fixing of signages, modular curved frame technology,of various widths and lengths, to form suggested usages,made of aluminium extruded sections , duly anodised ,all signages shall be provided with 0.6-0.8mm polycarbonate protecting film over the prints, of appropriate size, Complete all as per manufacturer's recommendations as directed by the Engineer-in-charge : AUTHORISED PERSONAL ONLY, Doctors name, etc. (80x300)

Providing and fixing of signages, modular curved frame technology,of various widths and lengths, to form suggested usages,made of aluminium extruded sections , duly anodised ,all signages shall be provided with 0.6-0.8mm polycarbonate protecting film over the prints, of appropriate size, Complete all as per manufacturer's recommendations as directed by the Engineer-in-charge : DRINKING WATER (200x200)

Providing and fixing of signages,customised to the architect's design,the signage to be made of 10 mm casted clear acrylic sheet duly cut by laser, all text to be of 2 mm thick acrylic duly laser cut, partially housed and pasted on to engraved surface of the text in the clear acrylic base, the 10mm acrylic sheet to be fixed on 25x25mm section of teak wood with help of crafted SS pins, and further fixed to the priscribed location with the help of wooden dowels,and required adhesive,as per drawing. Complete all as per manufacturer's recommendations as directed by the Engineer-in-charge: MAIN DIRECTORY (1200x1000)

Providing and fixing of signages,customised to the architect's design,the signage to be made of 10 mm casted clear acrylic sheet duly cut by laser, all text to be of 2 mm thick acrylic duly laser cut, partially housed and pasted on to engraved surface of the text in the clear acrylic base, the 10mm acrylic sheet to be fixed on 25x25mm section of teak wood with help of crafted SS pins, and further fixed to the priscribed location with the help of wooden dowels,and required adhesive,as per drawing. Complete all as per manufacturer's recommendations as directed by the Engineer-in-charge : FLOOR (600x300)

Providing and fixing of signages,customised to the architect's design,the signage to be made of 10 mm casted clear acrylic sheet duly cut by laser, all text to be of 2 mm thick acrylic duly laser cut, partially housed and pasted on to engraved surface of the text in the clear acrylic base, the 10mm acrylic sheet to be fixed on 25x25mm section of teak wood with help of crafted SS pins, and further fixed to the priscribed location with the help of wooden dowels,and required adhesive,as per drawing. Complete all as per manufacturer's recommendations as directed by the Engineer-in-charge: FLOOR LEVEL (600x300)

Providing Design/Fabrication of SS Letter cut out on SS Grade 202 Steel.Corrosion Resistance/Hardened/ High Strength.Approved Design Preparation of Letter and Fonts on AUTOCAD .Plasma Cutting on Stainless Steel with Nitrigen to give excellent surface finish for edge .Griding and Fabrication of Letterswelding.Font Size: 18" Complete all as per manufacturer's recommendations as directed by the Engineer-in-charge.

Making Tribal art on pre painted wall and specified tree trunk with superior quality weather coat including one coat, background painting of different shades including primer coat and pictoral figures/writing with appropriate paint for prominent look and including cost of paint, labour, material like paint brush and tools and plants required for the work as per instructons of EIC.

SITC of Water Sprinkler system with all necessary accessories required to make it complete in all respect i.e Sprinkler coupler with foot baton assembly, Sprinkler nozzles, Riser pipe, Connecting nipple- System to be designed by Contractor as Per Direction Of Engineering In-Charge.

SITC- Black Flexible Rubber Hose Pipe (50 mm inner dia) - with all necessary fittings like Bend, Tee, Coupler, End Plug to make the system complete in all respect - System to be designed by contractor as Per Direction Of Engineering In-Charge.

Supply, Installation, Testing, and Commissioning of 12 W, LED Garden Light - as per specifications provided in NIT- as per direction of EIC

SITC - Penguin Dustbin Ht- 44 ", capacity - 20 Ltr , FRP Dustbin with artistic finishing (FRP thickness- >6 mm , All metalic parts (if requiured)- GI )- as Per Direction Of Engineering In-Charge.

SITC of Luxury Benches/out door garden benches- 5ft ( W-9ft x L-6 ft ) of FRP , Wooden Appearance, Supported /Fixed by system made of MS painted with appropriate paint, Artistic look etc. completed in all respect with all necessary fittings/fixures as per direction of EIC, Artisi. (Minimum MS Kg- 50 Kg)

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (including equivalent design mix)

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density).

Supplying and Stacking of Good Earth by mechanical transport including loading, unloading including royalty & carriage up to 5 KM complete.

Supplying and Stacking of Good Earth by mechanical transport including loading, unloading including royalty & carriage : Beyond 5 km upto 10 km

Supplying and Stacking of Good Earth by mechanical transport including loading, unloading including royalty & carriage : Beyond 10 km upto 20 km

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineerin- Charge: With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and laying Dense Graded Bituminous Macadam using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specificatons and directions of Engineer-in-Charge: 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity

Providing and applying tack coat using hot straight run bitumen of grade VG - 10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications : On W.M.M. @ 0.75 Kg / sqm

Providing and applying tack coat using hot straight run bitumen of grade VG - 10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications : On bituminous surface @ 0.50 Kg / sqm

Providing and laying seal coat over prepared surface of road with bitumen heated in bitumen boiler fitted with the spray set spraying using 98 kg of bitumen of grade VG - 10 and blinding surface with 0.90 cum of stone aggregate of 6.7 mm size (Passing 11.2 mm sieve and retained on 2.36 mm sieve) per 100 sqm of road surface, including rolling and finishing with power road roller all complete.

Providing and laying Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge. 40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing White polished squatting urinal for women with integral type foot rests of standrad Size , 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing, fixing, testing and commissioning of white colour vitreous China wall mounting type European water closet with C.P. bolts, nuts, C.I. chair or other hanging arrangements, bakelite seat & cover with concealed type cistern &Push plate, C.P. hinges & rubber buffers, C.P. brass screw, washer with all accessories. Including cutting & making good the walls & floors slab wherever required .. (Make - ROCA, Model - Cat. No :RE801472464, Seat cover RE890010200, Cistern cat no - RE890010200 & Push Plat cat no - RE890196001) or equivalent (Warranty -05 Years )

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required : 510x1040 mm bowl depth 250 mm

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Oval shape 450x350 mm (outer dimensions)

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm

Providing and fixing P.V.C. Waste pipe for sink or wash basin including P.V.C. waste fittings complete.: Semi rigid pipe : 40 mm dia.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge: 15 mm nominal dia

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. : 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931: 15 mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing white vitreous china Under Counter Basin , Rectangular Shape , with fixing all accessories of size 605 x410x200 mm , making it complete for the reception of pipes and fittings. ( Make - JAQUAR, Model - FNS WHT-40701) or quivalent (Warranty -05 Years )

Providing and fixing white vitreous china Under Counter Basin , Oval shape , with fixing all accessories of size 560x430x195 mm , making it complete for the reception of pipes and fittings. ( Make - JAQUAR, Model - FNS WHT-5701) or equivalent (Warranty -05 Years )

Providing and fixing 15mm C.P brass Central Hole Basin Mixer with Regular Spout without Popup Waste System with 450 mm Long Braided Hoses, 20 mm Cartridge Size for Wash Basin Including cutting and making good the walls wherever required. (Make JAQUAR , FLR-5167NB) or equivalent . (Warranty -05 Years )

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Supply, Installation, Testing, and Commissioning 15mm C.P brass Single Lever Basin Mixer for Wash Basin Including cutting and making good the walls wherever required. complete as per direction of Engineer-in-charge

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length : 15 mm nominal bore

Supply, Installation, Testing, and Commissioning C.P. brass 15 mm nominal bore two way bib cock . complete as per direction of Engineer-in-charge

Supply, Installation, Testing, and Commissioning C.P. cast brass twin coat hooks fixed to PVC rawl plug with SS screws, complete as per direction of Engineer-in-charge

Supply, Installation, Testing, and Commissioning health faucet with 1 m long flexible tube and wall hook including all fittings . complete as per direction of Engineer-in-charge

Supply, Installation, Testing, and Commissioning 15mm C.P brass Sink Mixerfor kitchen sink with swinging spout complete. Including cutting and making good the walls wherever required . complete as per direction of Engineer-in-charge

Supply, Installation, Testing, and Commissioning of C.P. brass 600 mm size towel rail fixed with C.P. brass screws complete in all respects. complete as per direction of Engineer-in-charge

Supply, Installation, Testing, and Commissioning of C.P. brass Soap Dish fixed with C.P. brass screws complete in all respects. complete as per direction of Engineer-in-charge

Providing and laying cement concrete in 1:2:4 ( 1cement : 2 Coarse sand : 4 graded stone aggregate 20 mm nominal size ) and curing complete, including cost of form work.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Supply, Installation, Testing and Commissioning of soil, waste, rain water and vent pipe mineral filled 3 layered (PP/PP mineral filled/PP) Polypropylene low noise pipes and fittings of min. density 1.3 to 1.9 gm/cm3, pipes of 40 mm – 200 mm including all fittings &amp; accessories such as coupler, elbow, tee, Y, reducer, access door, end cap, cowls, etc. for soil, waste and vent purpose in floors, ceiling suspended, or on walls, with leak proof joints etc. Joining pipes &amp; fittings with rubber sealing rings as per approved manufacturer recommendation. Wall chasing, holes, supporting, clamping, covering back with chicken mesh &amp; plaster and making the wall good as per approved shop drawing. Sound level of less than 20 dB(A) at flow rate of 4 L/s according to DIN 4109. Should have D-s2, d0 fire classification as per EN 13501 or B2 as per DIN 4102, short term hot water resistance upto 95°c and long term upto 90°c, chemical resistance of pH 2 to pH12 - Should have IAPMO and Green certification. (Make - Wavin,Rehau, Ostendrof or equivalent ) complete job as per direction of Engineer-in-charge : 110 mm dia (Warranty -05 Years )

Supply, Installation, Testing and Commissioning of soil, waste, rain water and vent pipe mineral filled 3 layered (PP/PP mineral filled/PP) Polypropylene low noise pipes and fittings of min. density 1.3 to 1.9 gm/cm3, pipes of 40 mm – 200 mm including all fittings &amp; accessories such as coupler, elbow, tee, Y, reducer, access door, end cap, cowls, etc. for soil, waste and vent purpose in floors, ceiling suspended, or on walls, with leak proof joints etc. Joining pipes &amp; fittings with rubber sealing rings as per approved manufacturer recommendation. Wall chasing, holes, supporting, clamping, covering back with chicken mesh &amp; plaster and making the wall good as per approved shop drawing. Sound level of less than 20 dB(A) at flow rate of 4 L/s according to DIN 4109. Should have D-s2, d0 fire classification as per EN 13501 or B2 as per DIN 4102, short term hot water resistance upto 95°c and long term upto 90°c, chemical resistance of pH 2 to pH12 - Should have IAPMO and Green certification. (Make - Wavin,Rehau, Ostendrof or equivalent ) complete job as per direction of Engineer-in-charge : 50 mm dia . (Warranty -05 Years )

Supply, Installation, Testing and Commissioning of soil, waste, rain water and vent pipe mineral filled 3 layered (PP/PP mineral filled/PP) Polypropylene low noise pipes and fittings of min. density 1.3 to 1.9 gm/cm3, pipes of 40 mm – 200 mm including all fittings &amp; accessories such as coupler, elbow, tee, Y, reducer, access door, end cap, cowls, etc. for soil, waste and vent purpose in floors, ceiling suspended, or on walls, with leak proof joints etc. Joining pipes &amp; fittings with rubber sealing rings as per approved manufacturer recommendation. Wall chasing, holes, supporting, clamping, covering back with chicken mesh &amp; plaster and making the wall good as per approved shop drawing. Sound level of less than 20 dB(A) at flow rate of 4 L/s according to DIN 4109. Should have D-s2, d0 fire classification as per EN 13501 or B2 as per DIN 4102, short term hot water resistance upto 95°c and long term upto 90°c, chemical resistance of pH 2 to pH12 - Should have IAPMO and Green certification. (Make - Wavin,Rehau, Ostendrof or equivalent ) complete job as per direction of Engineer-in-charge : 40 mm dia (Warranty -05 Years )

Supply, Installation, Testing, and Commissioning PP 110mm P Trap with minimum 50mm water seal with rubber seal on inlet to push fit hopper for indirect waste connections.complete job as per direction of Engineer-in-charge

Supply, Installation, Testing, and Commissioning of pipe inlet fittings fabricated with Polyproplene Pipe with maximum 3 inlets 40, 50 & 75 mm OD size Polyproplene pipe, fixed to 'P' traps including Dripseal/Pipe seal/solvent /rubber ring joint complete . complete job as per direction of Engineer-in-charge

Supply, Installation, Testing, and Commissioning floor drain with 50mm outlet and 100 mm inlet having 50mm seal for indirect floor drain /balcony Drain. complete job as per direction of Engineer-in-charge

Supply, Installation, Testing, and Commissioning heavy duty square tainless steel grating with hinged cockroach trap. complete job as per direction of Engineer-in-charge

Providing, fixing, testing and commissioning end cap (door piece) of pp for cleaning. complete job as per direction of Engineer-in-charge : 110 mm dia

Supply, Installation, Testing, and Commissioning vent cowl. complete job as per direction of Engineer-in-charge : 110 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge : Internal Work - Exposed on Wall : 25 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge : Internal Work - Exposed on Wall : 32 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge : Internal Work - Exposed on Wall : 40 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge : Internal Work - Exposed on Wall : 50 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge : Concealed work including cutting chases and making good the walls etc. : 20 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge : Concealed work including cutting chases and making good the walls etc. : 25 mm nominal outer dia .Pipes.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work - Exposed on Wall For Roof : 25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work - Exposed on Wall For Roof : 32 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work - Exposed on Wall For Roof : 40 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work - Exposed on Wall For Roof : 50 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work - Exposed on Wall For Roof : 65 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work - Exposed on Wall For Roof : 80 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work - Exposed on Wall For Roof : 100 mm dia nominal bore

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : Two or more coats on new worke

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :20 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 25 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 32 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 40 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 50 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 65 mm dia. nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 80 mm dia. nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required. : 65 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required. : 80 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required.: 100 mm dia

Supply, Installation, Testing, and Commissioning forged brass ball valve of brass body with hard chrome plated steel ball inside PTFE (Teflon) seat & ring with chrome plated centre handle with female BSP threads complete in all respects. complete job as per direction of Engineer-in-charge : 15 mm nominal bore

Supply, Installation, Testing, and Commissioning forged brass ball valve of brass body with hard chrome plated steel ball inside PTFE (Teflon) seat & ring with chrome plated centre handle with female BSP threads complete in all respects. complete job as per direction of Engineer-in-charge : 20 mm nominal bore

Supply, Installation, Testing, and Commissioning forged brass ball valve of brass body with hard chrome plated steel ball inside PTFE (Teflon) seat & ring with chrome plated centre handle with female BSP threads complete in all respects. complete job as per direction of Engineer-in-charge : 25 mm nominal bore

Supply, Installation, Testing, and Commissioning forged brass ball valve of brass body with hard chrome plated steel ball inside PTFE (Teflon) seat & ring with chrome plated centre handle with female BSP threads complete in all respects. complete job as per direction of Engineer-in-charge : 32 mm nominal bore

Supply, Installation, Testing, and Commissioning forged brass ball valve of brass body with hard chrome plated steel ball inside PTFE (Teflon) seat & ring with chrome plated centre handle with female BSP threads complete in all respects. complete job as per direction of Engineer-in-charge : 40 mm nominal bore

Supply, Installation, Testing, and Commissioning forged brass ball valve of brass body with hard chrome plated steel ball inside PTFE (Teflon) seat & ring with chrome plated centre handle with female BSP threads complete in all respects. complete job as per direction of Engineer-in-charge : 50 mm nominal bore

Supply, Installation, Testing, and Commissioning forged brass single acting air release valve with screwed inlet 25 mm dia. complete job as per direction of Engineer-in-charge

Supply, Installation, Testing, and Commissioning of Single phase electrical actuator operated wafer type rubber lined butterfly valve with by pass arrangement as per drawing attached including level controller, 3 nos. normal butter fly valves,necessary control and Power cables ( Maximum 10 M. Length of each type) and control panel installed on OH tank filling line near the tanks complete in all respects. complete job as per direction of Engineer-in-charge : 50 mm dia.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work : 25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work : 40 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work : 50 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work : 65 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. : External work : 80 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-orrosive bitumastic paint of approved quality : 25 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-orrosive bitumastic paint of approved quality : 40 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-orrosive bitumastic paint of approved quality : 50 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-orrosive bitumastic paint of approved quality : 65 mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti-orrosive bitumastic paint of approved quality : 80 mm dia nominal bore

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 25 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 40 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 50 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 65 mm dia. nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 80 mm dia. nominal bore

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 65 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80 mm dia

Supply, Installation, Testing, and Commissioning forged brass ball valve of brass body with hard chrome plated steel ball inside PTFE (Teflon) seat & ring with chrome plated centre handle with female BSP threads complete job as per direction of Engineer in Charge. : 25 mm nominal bore

Supply, Installation, Testing, and Commissioning forged brass ball valve of brass body with hard chrome plated steel ball inside PTFE (Teflon) seat & ring with chrome plated centre handle with female BSP threads complete job as per direction of Engineer in Charge. : 50 mm nominal bore

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 180x150 mm size P type : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With F.P.S. bricks with class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With F.P.S. bricks with class designation 7.5

Extra for depth for manholes : Size 90x80 cm : With F.P.S. bricks with class designation 7.5

Extra for depth for manholes : Size 120x90 cm : With F.P.S. bricks with class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and laying , fixing of HDPE DWC Pipes with all fittings & fixtures including testing of joints etc. complete. As per direction of EIC (for storm drainage) : 150 mm dia

Providing and laying , fixing of HDPE DWC Pipes with all fittings & fixtures including testing of joints etc. complete. As per direction of EIC (for storm drainage) : 250 mm dia

Providing and laying , fixing of HDPE DWC Pipes with all fittings & fixtures including testing of joints etc. complete. As per direction of EIC (for storm drainage) : 300 mm dia

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of HDPE pipes including bed concrete as per standard design : 150 mm dia

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of HDPE pipes including bed concrete as per standard design : 250 mm dia

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of HDPE pipes including bed concrete as per standard design : 300 mm dia

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20x20 mm square bar

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 19.19.1 L D- 2.5 , HD-20 , Circular shape 560 mm internal diameter

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement cincrete 1:2:4 mix (1cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) cement plastered on both sides with cement mortar 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete for pipes 100 to 230mm dia.

HYDT: Cost of Drilind 225 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site. : From 0.00 M to 50.00 M below G.L.

HYDT: Cost of Drilind 225 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site. : From 51.0 M to125.00 M

HYDT: Cost of Drilind 225 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site. : From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge. : 200 mm nominal size dia having minimum wall thickness 5.40 mm

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed/ plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge. : 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. : 200 mm clamp.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). : 200 mm dia

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm dia.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required : 100 mm dia

Supply, Lowering, installation & testing of KSB make or equivalent submersible pumping set with 3.7 HP to 5.0 HP motor 4/5 stage pump suitable for 45-60 m3 hr. at 60 to 100 mtr. Head respectively. With Three Phase. And submersible aluminium cable 10 sq.mm. from submersible pump to panel board with Panel Board for submersible pump fitted with DOL starter ammeter, voltmeter single phase preventer standard/indo/cop make MCB of off switch push bottom duly wired and made out of 16/18 SWG sheet complete job as per direction of Engineer in Charge.

Providing and laying Non Pressure NP-4 class (Heavy duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete: 600 mm dia RCC pipes.

Providing and laying Non Pressure NP-4 class (Heavy duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete: 1000 mm dia RCC pipes. (Laying by manual/ machanical means)

Fire Fighting : (A)Suppling, Installation, Testing and Commissioning of electric driven terrace pump suitable for automatic operation and consisting of following,complete in all respects,as required:(terrace pump) (B) Horizontal type,multistage,centrifugal, split casing pump of caste iron body and bronze impeller with stainless steel shaft,mechanical conforming to IS:1520b (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 Volts ,3 phase,50 Hz,AC supply with IP55 class of protection for inclosure, horizontal foot mounted type with class -'F' insultaion , conforming to IS-325. (D) M.S. febricated common baased place, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads. : 900 lpm at 35m Head

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42. : Providing and fixing ,Testing and commissioning 20 HP Straters Control panel for Submersible Pumb Star and delta connection(incl all charges),make of GIPPSION ,CROMPTON HAVELLS etc. or equivalent Three phase /415V/50Hz Auto and manual ,Run Capacitor capacity 34 mfd, Start capacitor capacity 150-200 mfd, Digital Ammeter & Voltmeter including thermal Biometric Relay 32A. For Terrace Pump Complete all job as directed by the Engineer-in-Charge

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metalseat,ISI marked complete with nuts,bolts washers,gaskets and conforming to IS 780 of following sizes as required. : 150 mm diameter

Providing and fixing,testing and commissioning of butterfly of valve of PN 1.6 rating with bronze/gun metal seat duly ISI marked complete with nuts,bolts washers,gaskets conorming to IS 13095 fo following sizes as required: 80 mm diameter

Providing and fixing,testing and commissioning of butterfly of valve of PN 1.6 rating with bronze/gun metal seat duly ISI marked complete with nuts,bolts washers,gaskets conorming to IS 13095 fo following sizes as required: 100 mm diameter

Providing and fixing,testing and commissioning of butterfly of valve of PN 1.6 rating with bronze/gun metal seat duly ISI marked complete with nuts,bolts washers,gaskets conorming to IS 13095 fo following sizes as required: 150 mm diameter

Providing installation, testing and commissioning of non return valve of following sizes conforming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required: 80 mm diameter

Providing installation, testing and commissioning of non return valve of following sizes conforming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required: 100 mm diameter

Providing installation, testing and commissioning of non return valve of following sizes conforming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required: 150 mm diameter

Providing and fixing, Testing and commissioning Direct Mounting Pressure Gauge Assemble with Gate/Ball Valve (incl all charges)make of WIKA, BAUMER,AKVALO etc. or equivalent , C-type male end connection,Nominal size of end connector thread 1/4 inch, thread type NPT Nominal sixe of the Dial 40 mm ,measurement range 0 to 400 bar, maximum working pressure 400bar,mateial stainless steel Gr 304 and Gr 316 including zero adjustment facility, over-range protection 110% FSD, glycerine liquid damping minimum ambeint temperature -20 degree celsius maximum 60 degree celsius,maximum medium temperature 100 degree celsius, conferming to IS:3624 latest. Complete all job as directed by the Engineer-in-Charge

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing and fixing, testing and commissioing with Certification Air release Valve / Drain Valve 150mm Dia (incluidng all charges) All complete work as directed by the Engineer-in-Charge

Providing and fixing MS Structure support for piping as required All complete job as directed by the Engineer-in-Charge

Providing,laying,testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 1239/3589 i/c including welding, exevation & proving cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221,refilling the trench etc.of following sizes complete as required. : 150 mm diameter

Providing,laying,testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/Is 1239 including welding, fittings liks elbows,tees,flanges,tapers,nut bolts,gaskets etc.And ixing the pipe on wall/ceiling with suitable clamps/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 100 mm diameter

Providing,laying,testin & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/Is 1239 including welding, fittings liks elbows,tees,flanges,tapers,nut bolts,gaskets etc.And ixing the pipe on wall/ceiling with suitable clamps/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 80 mm diameter

Providing,laying,testin & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/Is 1239 including welding, fittings liks elbows,tees,flanges,tapers,nut bolts,gaskets etc.And ixing the pipe on wall/ceiling with suitable clamps/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 65 mm diameter

Providing,laying,testin & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/Is 1239 including welding, fittings liks elbows,tees,flanges,tapers,nut bolts,gaskets etc.And ixing the pipe on wall/ceiling with suitable clamps/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 50 mm dia

Providing,laying,testin & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/Is 1239 including welding, fittings liks elbows,tees,flanges,tapers,nut bolts,gaskets etc.And ixing the pipe on wall/ceiling with suitable clamps/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 40 mm dia

Providing,laying,testin & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/Is 1239 including welding, fittings liks elbows,tees,flanges,tapers,nut bolts,gaskets etc.And ixing the pipe on wall/ceiling with suitable clamps/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 25 mm dia

Supplying & fixing single headed internal hydrant valve with instantanous gu metal/stainless steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290(type-A) with blank Gunmetal/stainless steel cap and chain as required: *Single headed gun metal : Single headed Stainlesss steel.

Supplying and fixing first-Aid Hose Reel with MS construction spray painted in post office red,conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hosethermo plastic(textile reinforced)type-2 as IS:12585 : 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipments on wall.Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe aand socket. : 40 m

Providing, fixing, testing & commissioning of 15mm dia uartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Providing, fixing, testing & commissioning of 15mm dia uartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent / Upright Sprinkler

Providing, fixing, testing & commissioning of 15mm dia uartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Horizontal side wall sprinkler

Providing, fixing, testing & commissioning of 15mm dia uartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Concealed sprinkler

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.: 1000 mm

Providing, fixing, testing and commissioning of full way level operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not lass than 15 kg/sq.cm with threaded/flanged complete with nuts, bolts, gaskets, washers etc. as required complete as per direction of Engineer incharge. : 25 mm NB

Providing, fixing, testing and commissioning of full way level operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not lass than 15 kg/sq.cm with threaded/flanged complete with nuts, bolts, gaskets, washers etc. as required complete as per direction of Engineer incharge. : 50 mm NB

Providing and fixing 25 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end) conferming to IS:781 latest. all complet job as C in all respect as directed by the Engineer-in-Charge

Supplying and fixing 63mm dia, 15m long RRL hose pipe with 63mm dia male and femalecouplings duly bound with GI wires, rivetsetc. Conforming to IS 636(type-A) as required: Gun metal

Supplying and fixing 63mm dia, gun metal short branch pipe with 20mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun metal

Providing and fixing , testing and commissioning of hose cabinet(including all charges) of size 450mm x 600mm x 250mm made of 3mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe conferming IS:636, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect as directed by the Engineer-in-Charge

Supplying, fixing,of fire brigade connetion of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd.for suitable dia MS pipe connection conforming to IS 904 as required. *4 way-150 mm dia M.S. pipe

Providing , fixing testing and commissioning Fire fighting Extinguisher Powder Type 6 kg including all charges(IS:4308) Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+)60oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects as directed by the Engineer-in-Charge

Providing and fixing ,testing and commissioning Fire fighting Extinguisher BC Type (incl all charges) Carbon Di-oxide TypeHigh pressure Extinguisher (service pressure >19 bar) , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)60oC Suitable for ‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity) .All compelete job as directed by the Engineer-in-Charge

Providing , fixing ,testing and commissioning Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 4308’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 60oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)All compelete job as directed by the Engineer-in-Charge

Supplying, installation, testing & commissioning ofm micro proceesor based intelligent addressable main fire alarm panel,central processing unit with the followinng loop modules and capable of supporting not less than 240 devices and minimum 120 detectors per loop and loop length up to 2 km,network communication card, minimum 320 character graphics/LCD display with touch screen or other keypad and minimum 4000 events history log in the non voilatile memory(EPROM),power supply unit ,48hrs back-up with 24 volt sealed maintenence free batteries with automatic charger.The panel shall have to facility to connect printer to printout log and facility to have seamless integrated with analog/digital voice evacuation system and shall be complete with all accessories.The panel shall be complete as per specification. : Supplying, installation, testing and commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning ofm micro proceesor based intelligent addressable main fire alarm panel,central processing unit with the followinng loop modules and capable of supporting not less than 240 devices and minimum 120 detectors per loop and loop length up to 2 km,network communication card, minimum 320 character graphics/LCD display with touch screen or other keypad and minimum 4000 events history log in the non voilatile memory(EPROM),power supply unit ,48hrs back-up with 24 volt sealed maintenence free batteries with automatic charger.The panel shall have to facility to connect printer to printout log and facility to have seamless integrated with analog/digital voice evacuation system and shall be complete with all accessories.The panel shall be complete as per specification. : Supplying, installation, testing and commissioning of addressable mannual call point complete as required.

Supplying, installation, testing & commissioning of micro proceesor based intelligent addressable main fire alarm panel,central processing unit with the followinng loop modules and capable of supporting not less than 240 devices and minimum 120 detectors per loop and loop length up to 2 km,network communication card, minimum 320 character graphics/LCD display with touch screen or other keypad and minimum 4000 events history log in the non voilatile memory(EPROM),power supply unit ,48hrs back-up with 24 volt sealed maintenence free batteries with automatic charger.The panel shall have to facility to connect printer to printout log and facility to have seamless integrated with analog/digital voice evacuation system and shall be complete with all accessories.The panel shall be complete as per specification. *Two loop panel.

Furnitures : Supply, Installation, Testing, and Commissioning of TV - 43 inch LED as per specifications provided in NIT . (Warranty -03 Years ) . Make - Sony/LG/Samsung or equivalent.

Furnitures : Supply, Installation, Testing, and Commissioning of TV - 75 inch LED as per specifications provided in NIT . (Warranty -03 Years ) . Make - Sony/LG/Samsung or equivalent.

Supply, Installation, Testing, and Commissioning Attendant Controlled Non Powered Wheel Chair with Fixed Seat Height -as per specifications provided in NIT . Make- Standrad make as approved by EIC.

Supply, Installation, Testing, and Commissioning of 3 Seater Public Place Seating Chair of SS 304 with arm and backrest WITH CUSHION - as per specifications provided in NIT . Make- Standrad make as approved by EIC.

Supply, Installation, Testing, and Commissioning mintage Stainless Steel Dust Bin 1 Bin Mounted with 1 Pole capacity 40 ltr mintage (Outdoor hanging swing bin with Lid OHSB-101)- as per specifications provided in NIT . Make- Standrad make as approved by EIC.

Conference chair : Supply, Installation, Testing, and Commissioning of Revolving Chair with Tilt working with torsion bar mechanism - as per specifications provided in NIT . (Warranty -05 Years ) . Make - Durian/Godrej or equivalent

Supply, Installation, Testing, and Commissioning of Drinking Water Cooler 40 litres / hour & Storage 80 litres - as per specifications provided in NIT . Make- Standrad make as approved by EIC.(Warranty -03 Years )

Supply, Installation, Testing, and Commissioning of Executive Table with Both side pedestal unit - Main Table+ERU with Pedestal) - as per specifications provided in NIT . (Warranty -05 Years ) . Make - Durian/Godrej or equivalent

Supply, Installation, Testing, and Commissioning of MODULAR TABLE L X D & H 1500 millimeter X 750 millimeter 750 millimeter or more -as per specifications provided in NIT . (Warranty -05 Years ) . Make - Durian/Godrej or equivalent

Reception Table : Supply, Installation, Testing, and Commissioning MODULAR TABLE L X D &H 1500 millimeter X 750 millimeter 775 millimeter or more -as per specifications provided in NIT . (Warranty -05 Years ) . Make - Durian/Godrej or equivalent

OPD VISITOR CHAIR : Supply, Installation, Testing, and Commissioning of Non-Revolving and Non Tilting chair with Armrest -as per specifications provided in NIT . (Warranty -05 Years ) . Make - Durian/Godrej or equivalent

Excutive Chair : Supply, Installation, Testing, and Commissioning of Revolving Chair with Synchronic tilt mechanism -as per specifications provided in NIT . (Warranty -05 Years ) . Make - Durian/Godrej or equivalent

Supply, Installation, Testing, and Commissioning of Silver Matte Apron Locker Cabinet - as per specifications provided in NIT . (Warranty -05 Years ) . Make - Durian/Godrej or equivalent

Supply, Installation, Testing, and Commissioning Rack Steel Adjustable-as per specifications provided in NIT . (Warranty -05 Years ) . Make - Durian/Godrej or equivalent

Supply, Installation, Testing, and Commissioning of 10 seaters Meeting Table- as per specifications provided in NIT . (Warranty -05 Years ) . Make - Durian/Godrej or equivalent

Supply, Installation, Testing, and Commissioning of 8 seaters Meeting Table- as per specifications provided in NIT . (Warranty -05 Years ) . Make - Durian/Godrej or equivalent

Supply, Installation, Testing, and Commissioning of Semifowler Patient Bed- as per specifications provided in NIT . (Warranty -03 Years ) . Make - Standard make as approved by EIC

Supply, Installation, Testing, and Commissioning of Wooden Almirah, Height 2100 - as per specifications provided in NIT . (Warranty -05 Years ) . Make - Durian/Godrej or equivalent

Supply, Installation, Testing, and Commissioning Laboratory Refrigerator >400<=450 Liters Capacity -as per specifications provided in NIT . (Warranty -As provided by manufacturer ) . Make - Voltas/LG/Godrej or equivalent

Supply, Installation, Testing, and Commissioning SSF Mild Steel Pipe of diameter 25 mm and wall thickness 1.1 mm minimum Classroom Chairs- as per specifications provided in NIT . (Warranty -03 Years ) . Make - Durian/Godrej or equivalent

Supply, Installation, Testing, and Commissioning of 7 Seater Sofa With Leather Fabric Cover -as per specifications provided in NIT . (Warranty -05 Years ) . Make - Durian/Godrej or equivalent

Electrical works : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required : Group C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. : Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. : 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. : 4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. : 4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as reqired. : 3 X 1.5 sq. mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as reqired. : 3 X 2.5 sq. mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as reqired. : 3 X 4.0 sq. mm

Supplying and Fixing of following sizes of steel conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. : 25 mm

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Providing and fixing M.S. Fan clamp of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC , earthing etc. complete as required

Supply of sizes 230 mm, 230 v A.C. heavay duity exhaust fan complete with motor,blades,frame, bracket, lover/shutter etc. as required of Cate. Ref. HAVELLS : FHVVEMTDBB09 or apporoved equivalent.

Supply and installation of 450 mm, 230 V A.C. wall mounted Air circulator, heavy duty fan including fixing the bracket, making connection, testing, commissioning etc as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required : Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes

Supply of Ultra modern recess mounting 36 watt (2' x 2') luminaire with high performance LEDs, suitable for mounting with Armstrong/Grid ceiling complete with all fixing accessories as required

Supply of Surface mounted 18W LED downlighter with white powder coated aluminium housing with integrated electronic driver etc,complete with all fixing accessories as required

Supply of Recessed mounted 18W LED Downlighter with Low depth Aluminium (99% Purity) Heat Sink, available in Round and Square shape. PC diffuser in white powder coated finish with independent electronic low THD (<10%) LED driver with higher design life class omplete with all fixing accessories as required

Supply of 22W LED, Basic all purpose surface and wall mounted LED batten with aluminum housing & integrated electronic driver

Supply of 10W LED, Bulkhead light.

Supply of 9W LED Surface mounted Downlight with Aluminium (99% Purity) Sink, available in Round shape. PC diffuser in white powder coated finish with built in electronic low THD (<10%) LED driver.,complete with all fixing accessories as required

MCB ,DB'S : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) : 6 way (4 + 18), Double door

MCB ,DB'S : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) : 8 way (4 + 24), Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator : 6 way, Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required : Single pole

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required : 40A

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required : 63A

Supplying and fixing following rating, double pole, 230 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required : 40A

Supplying and fixing following rating,four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. : 40A

Supplying and fixing following rating,four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. : 63A

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. : For 6 way, Double door TPN MCBDB

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with testing and commissioning etc.as required. : For 8 way, Double door TPN MCBDB

Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc.as required. : For 6 way, Double door SPN MCBDB

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required

EARTHING : Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm

LIGHTNING PROTECTION SYSTEM : Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required

CABLE WORKS : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. : Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. : Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. : Above 185 sq. mm and upto 400 sq. mm (clamped with 400x3mm MS flat clamp)

CABLE TERMINATION : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. : 3½ X 240 sq. mm (62mm)

CABLE TERMINATION : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. : 4 X 16 sq. mm (28mm)

CABLE TERMINATION : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. : 4 X 10 sq. mm (25mm)

Supplying and making end termination with brass connection gland and aluminum lugs for following size of PVC insulated and PVC sheathed/XLPE aluminum conductor cable of 1.1 kV grade as required : 3 × 10 sq.mm.(22 mm)

Supplying and making end termination with brass connection gland and aluminum lugs for following size of PVC insulated and PVC sheathed/XLPE aluminum conductor cable of 1.1 kV grade as required: 2 × 16 sq.mm (22 mm)

Supply of XLPE insulated and PVC sheathed power cable of 1.1 kV grade, 1.1 kV, multi core, aluminum,armored , underground, Conforming to IS 7098-2 : 3.5c x 240 sqmm

Supply of XLPE insulated and PVC sheathed power cable of 1.1 kV grade, 1.1 kV, multi core, aluminum,armored , underground, Conforming to IS 7098-2 : 4c x 16 sqmm

Supply of XLPE insulated and PVC sheathed power cable of 1.1 kV grade, 1.1 kV, multi core, aluminum,armored , underground, Conforming to IS 7098-2 : 4c x 10 sqmm

CABLE TRAY : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. : 150 mm width X 50 mm depth X 1.6 mm thickness

CABLE TRAY : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. : 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc.as required : 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc.as required : 300 mm width X 50 mm depth X 1.6 mm thickness

RACEWAY : Supplying and installation of following sizes 2.0 mm thick GI Raceways in recess/ on surface including chasing the wall/floor complete as required. : 75 mm x40 mmx2.0mm /2 comportment

Supplying and installation of following sizes Junction box on surface including chasing the floor complete as required. : 75 mm x40 mmx2.0mm /2 comportment

Supplying and installation of following sizes Vertical Bend in recess/ on surface including chasing the wall/floor complete as required. : 75 mm x40 mmx2.0mm /2 comportment

UPS I/O (MCCB BOX) : Fabrication, supply, installation, testing and commissionings of FP MCCB Box made out of 16mm thick CRCA sheet including connection, inter-connection as per CP WD specifications, ( Part IV - Sub-station) and IS: 8623 comprising of followings panel mounting switchgears etc. as required., INCOMING/OUTGOING: 1 Nos. 63Amps FP MCCB 16kA With thermal magenetic release for O/C,& S/C Protection. UPS I/O (MCCB BOX) above & as per SLD

UMDB : Fabrication, supply, installation, testing and commissionings of cubicle type floor/ wall mounted Main Distribution Board panel made out of 16mm thick CRCA sheet including connection, inter-connection alongwith 4 stsrip aluminium bus bar as per CPWD specifications, ( Part IV - Sub-station) and IS: 8623 comprising of followings panel mounting switchgears etc. as required., INCOMING : (a) 1 Nos. 63Amps TP MCCB With Double Neutral 16kA With thermal magenetic release for O/C,& S/C Protection. (b) One (1) Set of Phase Indication & ON/OFF Lamp with 2A SP MCB. BUSBAR: - 200 Amps TP&N aluminum conductor bus bar (BPTM type Heat-shrinkable busbar insulation) supported by DMC / FRP insulators. OUTGOINGS: - 6 nos. 40A FP MCB 10kA With TM Based Release (O/C,S/C) Protection & Rom : UMDB above & as per SLD

UPS : Supply,installation, testing & commissiong of micro processor /DSP controlled 20 KVA UPS operating without redundancy and having IGBT based rectifier to achieve THDI < 1% for linear load and < 3% for non linear load, input power factor of greater than 0.99, output power factor 0.9, efficiency 93% minimum at 100% loading. True Online Double Conversion (VFI as per IEC 62040-3) UPS using PWM IGBT technology on charger and inverter section , 3 Phase input and 3 phase 415 V output UPS system.with Sealed Lead Acid Maintenance free 12V batteries (of Exide) with Rack for 20kVA UPS with 30 Mins. backup time on each UPS module with inerconnectors as per specification.

Supplying, installing, testing & commissioning digital (hybrid) type EPABX of 6 x 32 universal extensions suitable upto 96 extensions compliant to IEC 61000, EN 60950, CISPR 22, IS:9000 part 2/section 4 having LAN/WAN port, USB port, RS232 port as per specification complete

Supply, Installation, Testing and Commissioning of Analog phone with caller id , speaker and display Make- Beetel / Matrix/ Unify

Supplying, erecting & commissioning 20 pairs FR junction box with moulded plastic enclosure as per specification

Supplying, erecting & commissioning 10 pair module for connection & disconnection of telephone cable

Supply, installation, testing and commissioning of Face Plate 1 Port - White with I/o complete as per the requirement & complete in all respect and as directed to the satisfaction of engineer

Supply, Installation, Testing & Commissioning of 24 Port Layer 2 Managed Access Non POE switch with 24x1G Base-T Ports and 4x1G Base-T Ports.Should support switching fabric of 240 Gbps or more. Operating Temp: 0° C to +50° C Make: Cisco/ Juniper/ Allied Telesys/ D Link or equivalent

Supply , Installation, Testing and Commissioing of 24 port Patch Panel, Make Legrand/Dlink/Molex or equivalent

Supply , Installation, Testing and Commissioing of UTP Patch cord-1 Mtr

Supplying and Drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as Required. : 1 run of cable

Supplying and Drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as Required. : 2 run of cable

Supplying and Drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as Required. : 3 run of cable

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. : Telephone socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. : TV antenna socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required : 1 or 2 Module (75mmX75mm)

CCTV : Supply , Installation, Testing and Commissioing of 4MP IR Indoor Dome Camera -1/3" Progressive Scan CMOS, 2688 × 1520 at 25fps, 2.8mm Fixed lens, 0.01 Lux at F1.2, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, IK10, Alarm & Audio: 1 input & 1 output, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Audio exception detection, video tampering, UL, CE, FCC certified.. 3 Years Standard Warranty. Preferred Make: Bosch/Hikvision/Pelco or equivalent

Supply of 55" LED Panel, 4K LED Screen for live view and replay of recorded View with mounting stand & HDMI cable. Make: Samsung/LG/Sony or equivalent

Supply , Installation, Testing and Commissioing of 8 TB of Storage Harddisk inside Servers ( H.265/ 60 days / 2 MP/ 15 fps) for cameras Make: Seagate/ Western Digital or equivalent

Supply, installation, testing & commissioning of 24 Port Layer 2 Managed Access POE switch with 20x1G Base-T PoE+ and 4x1G Base-T Ports.Should support switching fabric of 240 Gbps or more. Should support PoE+ with PoE budget of 300 W. Operating Temp: 0° C to +50° C Make: Cisco/ Juniper/ Allied Telesys/ D Link or equivalent

Supply fitting, fixing and testing of 9 U Wall/Pole mount weather proof rack for keeping switch & other items in the filed along with all required acessories . Make: D-Link / Omnitech/DATARACK or equivalent

Supply, Installation, Testing and Commisioning of RJ45 Connectors

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable beam detector with short circuit isolator (inbuilt or seperate) complete with emitter and receiver including connections with remote test features etc complete as required.

Supplying, installation, testing & commissioning of intelligent addressable duct detector including suitable Photo detector complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

PUBLIC ADDRESS SYSTEM : Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms operating at 240 Volt AC Supply complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.

Supplying and laying of 2X1.5 sqmm fire alarm armoured cable,600/1000V rated with annealed copper conductor having XLPE insulation,steel wire armouring & FRLS outer sheath complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. : speaker cable Single pair, 2-core, 1.5 sqmm

DG SET WITH AMF PANEL : Supply, Installation Testing and commissioning of DG Set complete with 1500 RPM Diesel Engine of suitable BHP & AC Brush less SPDP alternator mounted on a common base Frame & coupled through a flexible coupling or close coupled. (a) Alternator: It shall be self regulated, self excited and confirms to IS: 13364/1992 or latest version with regulation of +5% from No load to full load, IP23, with standard Alternator Protection( Over voltage, over speed & under voltage). (b) Diesel Engine: It shall have residential silencer, up to 10 M exhaust piping, Electronic / Mechanical governor, Manual & electric Start, Batteries, Fuel tank (with Stand) & piping, control panel (16 G) with MCCB (4P; 25 KA), Ammeter, Voltmeter, Frequency Meter, Energy Meter & Hour Meter, Engine instruments panel and AVM. The diesel engine shall be capable of providing 10% over load for 1 Hr for every 11 Hrs of continuious running at full load. (c) The enclosure has built in fuel tank, residential silencer (isolated from main DG chamber) with protection and tripping of DG set against temperature of more than 50 °C. All controls for operation of DG set are from outside the enclosure with DG control panel having processor based genset monitoring and control system MCCB/ACB Ammeter, voltmeter, Pf meter, frequency meter, KWH meter, Indication Lamps etc. mounted inside enclosure, visible and accessible from outside. The enclosure should be suitable for following capacity DG sets and alternator. Noise level is less than 75 db (A) at a distance of 1 Mtrs as per Lattest CPCB norms, complete in all respect of following capacity : DG set comprising of Cummins make Engine coupled to Stamford make Alternator or equivalent, mounted on a common base frame, complete with: a) AMF Panel , b) Fuel Tank , c) Battery & Leads , d) Silencer - Residential e) AVM Pads f) First Fill of Lube Oil g) Acoustic Enclosure : 320 KVA DG set at 0.8 pf 415V 50Hz 3-Ø.

Design, manufacture supply, installation, testing, commissioning, approvals and handing over in satisfactory working condition of the following Bed Lifts with Microprocessor based ACVVVF control, Group full collective operation, car enclosure and car / landing doors with stainless steel hairline finish, car floor with PVC finish including provisions for, use by handicapped persons, all controls, accessories, fittings and safety devices (like ARD) and including the cost of providing satisfactory trial operation for 4 weeks after completion and including the cost of providing free comprehensive maintenance of lifts and associated items for 10 Years ( including warranty period -01 Year) after handing over complete as per specifications, as required and as below. : 20 person (Bed Lift) capacity 0.75 mps speed and G+1 (2) stops with all openings on the same side (below false ceiling) with automatic center opening doors. As per specification. Note: Lift pit depth & overhead etc. will be as per NBC norms. (As per dertailed specifications provided in NIT)

Providing and fixing MV. danger notice plate of 200 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required 200 mm dia (OD-200 mm & ID-175 mm nominal)

HVAC System : Supply Installation,Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume aircooled Outdoorunits suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s),minimum two compressor for above 14HP modules, microprocessor based Controller,top discharge type condensing unit(s),with R410 A Refrigerant, vibration isolators, with suitable foundation etc. complete asrequired. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperatur without tripping. The unit shall be suitable to work on 400V+/-10%,3Phase,50Hz AC power supply.The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 . : 8.0HP ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supply Installation,Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume aircooled Outdoorunits suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s),minimum two compressor for above 14HP modules, microprocessor based Controller,top discharge type condensing unit(s),with R410 A Refrigerant, vibration isolators, with suitable foundation etc. complete asrequired. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperatur without tripping. The unit shall be suitable to work on 400V+/-10%,3Phase,50Hz AC power supply.The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 . : 18HP ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supply Installation,Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume aircooled Outdoorunits suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s),minimum two compressor for above 14HP modules, microprocessor based Controller,top discharge type condensing unit(s),with R410 A Refrigerant, vibration isolators, with suitable foundation etc. complete asrequired. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperatur without tripping. The unit shall be suitable to work on 400V+/-10%,3Phase,50Hz AC power supply.The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 . : 24HP ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supply Installation,Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume aircooled Outdoorunits suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s),minimum two compressor for above 14HP modules, microprocessor based Controller,top discharge type condensing unit(s),with R410 A Refrigerant, vibration isolators, with suitable foundation etc. complete asrequired. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperatur without tripping. The unit shall be suitable to work on 400V+/-10%,3Phase,50Hz AC power supply.The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 . : 36HP ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

VRV/VRF INDOOR UNITS: Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower ,multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drainpan, other necessary supports etc., suitable for operation on single phase AC supply 230V±10%,50 Hz complete as required. The unit shall have automatic force shut down provision in case of fire on receiveing signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. : 5.5 TR Ductable unit H.S ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

VRV/VRF INDOOR UNITS: Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower ,multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drainpan, other necessary supports etc., suitable for operation on single phase AC supply 230V±10%,50 Hz complete as required. The unit shall have automatic force shut down provision in case of fire on receiveing signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. : 7.0 TR Ductable unit H.S ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. : 2.3 / 2.4 TR Cassette unit ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. : 3.2 TR Cassette unit ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. : 1.5 TR Hi wall unit ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. : 2.0 TR Hi wall unit ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supply Installation, testing, commissioning of supply & return Y-joints sets of required size for refrigerant piping as per manufacturer standards. : Y- Joints set ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

REFRIGERANT PIPING: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

REFRIGERANT PIPING: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

REFRIGERANT PIPING: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required :12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

REFRIGERANT PIPING: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

REFRIGERANT PIPING: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

REFRIGERANT PIPING: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

REFRIGERANT PIPING: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

REFRIGERANT PIPING: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

REFRIGERANT PIPING: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

REFRIGERANT PIPING: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

REFRIGERANT PIPING: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

REFRIGERANT PIPING: Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

DRAIN PIPING : Providing and fixing of uPVC drain pipe of 6 Kg /cm2 pressure rating complete with 6mm thick closed cell nitrile rubber insulation, fittings, supports, valves as per specifications & drawings. : 25 mm dia ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

DRAIN PIPING : Providing and fixing of uPVC drain pipe of 6 Kg /cm2 pressure rating complete with 6mm thick closed cell nitrile rubber insulation, fittings, supports, valves as per specifications & drawings. : 32 mm dia ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

AIR COOLED INVERTER TYPE SPLIT AC : SPLIT AC (inverter model) :- Supply, installation, testing and commissioning of Split type wall mounted air conditioning unit of following capacity including indoor, outdoor unit fitted with inverter based rotary compressor, copper condenser and first charge refrigerant R410A. The condensing unit working range should be capable for providing cooling between +/-5 deg. C to 50 deg. C & heating within 0 deg.C to 15 deg. C including connection of copper pipe of required size upto 3 mtr., insulation, cordless remote control, auto air swing louvers, wall stand for outdoor unit, connection copper lead wire, condensed water outlet pipe 2 mtr.complete etc as required. Outdoor/indoor units should be of same make (brand) : Note : Aluminium Fins and copper tubes of Air Cooled Condenser along with copper tubing / piping with all joints and U-Bends exposed to coastal areas corrosive atmosphere / aggressive ambient, shall be painted with special corrosion prevention coating either in factory or at site. : 1.0 TR Hi wall unit with drain pump 5-Star Server Room ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for SPLIT AC system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : Dia 6.4 mm OD 13mm thick insulation ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for SPLIT AC system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : Dia 12.7 mm OD 13mm thick insulation ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Sheet Metal Duct: Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. : Thickness 0.63 mm sheet (24 G) ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. : Thickness 0.63 mm sheet (24 G) ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supplying, fixing. testing commissioningof GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, in accordance with approved shop drawings and specifications complete as required.( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core.( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supply and fixing of Acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (class "O") insulation on existing duct after applying two coats of cold setting adhesive (CPR X compound). The joints shall sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. : 19 mm ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supply, installation and balancing of extruded aluminium powder coated air louvers complete with aluminium wire mesh bird screen and damper as per specifications.( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supply, fabrication, installation and testing the non-porous 200mm wide flexible connections constructed of fire resistance flexible, double canvas connection with resistoflex material as per the approved shop drawings.( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

INLINE TYPE FAN : Supply, installation, testing and commissioning of ducted Inline Fans of GSS construction (rectangular box type above 900cfm for upto 25 mm WG S.P and circular type for 10 mm WG SP upto 850cfm) with centrifugal blower and motor encased in sheet metal casing, canvas connection etc. The Fan motor shall be suitable for operation on 220 V± 10%, 50 Hz, 1 phase AC supply upto 2500cfm and above 400 V 3phase. noise level not more than 65dBA from 1 m The Fan assembly shall conform to specifications and in accordance with requirements of drawings and Schedule of Quantities. : 500cfm capacity with 10 mm static pressure ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

PROPELLER FANS : Supply, Installation, Testing and commissioning of wall mounted GSS/MS propeller type exhaust fans of Axial Flow type with light weight type MS / aluminium impellers with aerofoil contours for high efficiency and low noise. The fan shall be supplied complete with and gravity louvers with a suitable Squirrel cage induction motor. : 225 mm dia 900RPM ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

MCB FOR Split AC: Supplying and fixing 5A to 32A rating 230/415V "C" curve, miniature circuit breaker suitable for inductive load of following poles in the MCB DB complete with connections, testing and commissioning etc. as required. : Double pole ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supplying & laying of following 1100 volt grade XLPE insulated PVC sheathed COPPER conductor armoured cables including , clamped includes anchor fastners wall with suitable clamps, saddles fixing bolts including connecting testing and commissioning etc as per specification complete as required lugs,terminations & gland etc. : 4C x 6 Sq.mm. ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supplying & laying of following 1100 volt grade XLPE insulated PVC sheathed COPPER conductor armoured cables including , clamped includes anchor fastners wall with suitable clamps, saddles fixing bolts including connecting testing and commissioning etc as per specification complete as required lugs,terminations & gland etc. : 4C x 10 Sq.mm.( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supplying & laying of following 1100 volt grade XLPE insulated PVC sheathed COPPER conductor armoured cables including , clamped includes anchor fastners wall with suitable clamps, saddles fixing bolts including connecting testing and commissioning etc as per specification complete as required lugs,terminations & gland etc. : 4C x 16 Sq.mm.

Supplying & laying of following 1100 volt grade XLPE insulated PVC sheathed COPPER conductor armoured cables including , clamped includes anchor fastners wall with suitable clamps, saddles fixing bolts including connecting testing and commissioning etc as per specification complete as required lugs,terminations & gland etc. : 4C x 25 Sq.mm.

Supplying and installing following size of perforated painted with powder coating MS. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with MS, suspenders including bolts & nuts, painting suspenders etc as required. : 100 x 50 mm x 1.6mm thick ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supplying and installing following size of perforated painted with powder coating MS. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with MS, suspenders including bolts & nuts, painting suspenders etc as required. : 300 x 50 mm x 1.6mm thick ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. : 25mm ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. : 2 x 1.5 sq. mm ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. : 4 x 2.5 sq. mm ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. ( including Free Comperehensive Maintenance for 10 years (including warranty period -01 year)

Total impact of GST for the purpose of CTC