Const. of Prohibited Muddamal Shed [ Incl. Electrical Work] and Drilling of 250 MM Dia X 380 Mt. Deep Tube Well (1 Nos) At - Varahi Police Station Dist.Patan. (2nd Attempt)

NO. IN FIGURE IN WORDS Rs.

Excavation for foundation upto 1.5 Mt. depth including sorting out and stacking of useful Rs. One Hundred Twenty

1 materials and disposing of the excavated stuff for all lead and lift. [[a]Loose & Soft 100.00 Cum. 127.51

Seven & Paise Fifty One Only

Providing and laying cement concrete 1:2:4 (1-cement:2-coarse sand:4-stone aggregates 20 mm Rs. Three Thousand Five

2 of nominal size) and curing etc.complete including cost of formwork in Faundation & Plinth. 6.00 Cum. 3540.09 Hundred Forty & Paise Nine

Providing and laying cement concrete 1:4:8 (1 cement :4 coarse sand , 8 graded machine broken Rs. Two Thousand Six

3 stone aggregate 40mm nominal size ) and curring complete excluding cost of from work in 2.00 Cum. 2633.97 Hundred Thirty Three & Paise

Faundation & Plinth. Ninety Seven Only

Providing TMT Bars Fe - 500 reinforcement of any other approved brand of GSPHC ONLY

for RCC work including cutting, bending, binding and placing in position etc.complete for all Rs. Seventy Six & Paise Fifty

floors. Two Only

Provinding and Laying controlled cement concrete M-250 including finising smooth with curing Rs. Four Thousand Five

5 complete including the cost of form workbut excluding the cost of reinforced concrete work in 14.00 Cum. 4510.17 Hundred Ten & Paise

foundetion FOOTING and mass cocrete. Seventeen Only

Provinding and Laying controlled cement concrete M-250 & including finising smooth with Rs. Nine Thousand Three

6 curing complete including the cost of form work but excluding cost of reinforcement for R.C.C 2.00 Cum. 9328.26 Hundred Twenty Eight &

work in COLUMN UP TO PLINTH for any cross sectional area of column. Paise Twenty Six Only

Brick work using common burnt clay building bricks having crushing strength not less than 35 Rs. Three Thousand Six

7 kg./Sq.Cm. in foundation and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) 9.00 Cum. 3672.26 Hundred Seventy Two & Paise

Conventional Twenty Six Only

Provinding and Laying controlled cement concrete M-250 & including finising smooth with Rs. Seven Thousand One

8 curing complete including the cost of form work but excluding cost of reinforcement concrete for 4.00 Cum. 7183.52 Hundred Eighty Three & Paise

PLINTH BEAM for any cross sectional Area of Beam. Fifty Two Only

9 20cms.In depth consolidating each deposited layer by ramming and watering. 74.00 Cum. 271.15

One & Paise Fifteen Only

Supplying and Filling in plinth with sand under floors including watering, ramming, Rs. Four Hundred Twenty

10 consolidation and dressing etc.complete 5.00 Cum. 424.99 Four & Paise Ninety Nine

Applying general insecticide pest control treatment to floors, cupboards etc. including labour,

material ETC. complete.USING lmidacloprid 30.5 Scas PER IS 6313 PART II(0.075% Rs. Ninety & Paise Seventy

11 concentration by mass)is recommended 10.5ml chemical diluted with 5 liters of water aplication 50.00 Sqm. 90.72

o.5 litre chemical/sqm of surface is recommended asper i.s

ITEM ESTIMATED RATE [Rs. Ps.] AMOUNT

DESCRIPTION OF ITEMS QUANTITY UNIT

NO. IN FIGURE IN WORDS Rs.

Providing and laying cement concrete 1:5:10 (1-cement;5-coarse sand;10-graded brick aggregate Rs. Two Thousand Four

12 of 40mm nominal size) and curing etc.complete excluding cost of formwork in foundation and 4.00 Cum. 2472.81 Hundred Seventy Two & Paise

plinth. Eighty One Only

Provinding and Laying controlled cement concrete M-200 Finishing smooth with curing

etc.comp including the cost of formwork but excluding the cost of reinforcement for RCC work Rs. Three Thousand Nine

13 in SLAB having thickness of 10cm upto 13cm for Grade slab.[Formwork shall be used with 8.00 Cum. 3900.33 Hundred & Paise Thirty Three

Plywood shuttering & steel props.] Only

Provinding and Laying controlled cement concrete M-250 and with curing etc.complete.

Including the cost of formwork but excluding the cost of reinforcement for R.C.C work in Rs. Ten Thousand Eight

14 Column having any cross section area of Ground Floor Columns. [Formwork shall be used with 4.00 Cum. 10843.78 Hundred Forty Three & Paise

Plywood shuttering & steel props.] Seventy Eight Only

Provinding and Laying controlled cement concrete M-250 and with curing etc.complete. Rs. Eight Thousand Seven

15 Including the cost of formwork but excluding the cost of reinforcement for R.C.C work in Lintel. 1.00 Cum. 8739.17 Hundred Thirty Nine & Paise

For Ground Floor. [Formwork shall be used with Plywood shuttering & steel props.] Seventeen Only

Provinding and Laying controlled cement concrete M-250 and with curing etc.complete.

Including the cost of formwork but excluding the cost of reinforcement for R.C.C work in Lintel Rs. Five Thousand Nine

16 Bend. For Ground Floor. [Formwork shall be used with Plywood shuttering & steel props.] 1.00 Cum. 5946.01 Hundred Forty Six & Paise

Brick work using common burnt clay building bricks having crushing strength not less than 35 Rs. Three Thousand Nine

17 Kg/Sq.cm.in superstructure above plinth up to floor two level in conventional bricks in cement 23.00 Cum. 3964.48 Hundred Sixty Four & Paise

mortar 1:6(1-cement;6-fine sand) for Ground Floor. Forty Eight Only

Provinding and fixing chicken wire mesh Jali 0.18 mm and 0.18m wide with necessary screws

and nails to joint between R.C.C. column and brick work etc. complete as per Engineer-in- Rs. Sixty Four & Paise Six

charge. Only

Provinding 15 mm thick cement PLASTER in single coat on brick or concrete wall for interior

plastering and finished even and smooth in C.M. 1:4 ( 1 cement : 4 sand ) including finishing Rs. Two Hundred Ninteen &

with floating coat of neat cement slurry at GROUND FLOOR. Paise Seventy Only

Providing 20mm thick sand faced cement plaster on walls above ground level consisting 12mm

thick backing coat of C.M.1:3 (1-cement;3-sand) and 8mm thick finishing coat of C.M.1:1(1- Rs. Three Hundred Twenty

cement;1-sand) etc.complete for any height. Seven & Paise Forty Five Only

Provinding CEMENT VATA (10cm x 10cm) size quarter round in cement mortar (1 : 1) Rs. Twenty Four & Paise Four

21 including neat cement finishing, watering etc. Complete. 28.00 Rmt 24.04

Providing and Laying Mirror Polished (Dimond Polished) Polished Kota Stone Flooring over

20mm thick base of cement mortar 1 : 6 (1-Cement : 6-Coarse Sand) laid over and jointed with Rs. One Thousand One

22 grey cement slurry including Rubbing and Polishing etc. Complete. (A) 25mm Thick. In Green 50.00 Sqm. 1108.30 Hundred Eight & Paise Thirty

Colour. Rate Are Inclusive of Single Piece & Making 3 Line Groove & Moulding Of Outer edge Only

as Directed By Engineer In Charge

Providing and Laying Double Pre Polished (Dimond Polished) 25mm Thick Polished Kota Stone

in Skirtings over 10mm thick base of cement mortar 1 : 3 (1-Cement :3-Coarse Sand) laid over Rs. One Thousand Two

and jointed with grey cement slurry including Rubbing and Polishing etc. Complete for ALL Hundred Seventy Two Only

ITEM ESTIMATED RATE [Rs. Ps.] AMOUNT

DESCRIPTION OF ITEMS QUANTITY UNIT

NO. IN FIGURE IN WORDS Rs.

Providing and Fixing Granite of Telephonic Black Colour 15 to 18mm thick for jambs and sills

of doors & windows using neat cement slurry laid over 20 mm average base of cement mortar

1:1 (1 cement:1 Coarse Sand) and jointed with grey cement slurry including racking (Tancha Rs. Two Thousand Four

24 Work) rubbing and polishing, scaffoldings, tools and tackles, scaffolding etc. complete. (with 6.00 Sqm. 2428.00

Hundred Twenty Eight Only

base of neat cement) as per direction of Engineer in charge including rounding the exposed edges

as directed etc. Complete for ALL FLOORS

Providing and fixing both side prepolished single piece machine cut 25mm thick KOTA STONE

shelve/ partition, 20mm to 25mm embedded in to wall at support including racking and finishing Rs. Seven Hundred Ninety

25 smooth the surface including cutting the stone as and where required etc. complete including 59.00 Sqm. 793.90

Three & Paise Ninety Only

moulding of exposed edges etc. complete.

Providing, Fabricating and fixing M.S. GRILL/GATE of approved pattern fabricated from M.S.

flat,square bars, round bars,c-channel, box pipe as per detail Drawings. Rate is inclusive of

welding with grinding smooth surface, two coats of Oil paint and one coat of yellow Zinc

Rs. Seventy Five & Paise

26 primer coat of approved brand only. Oil paint shall be Luxol Enamel paint of Berger Paint india 119.00 Kg. 75.29

Twenty Nine Only

limited. or asian paint apcolite premium gloss Enamel of asian paint or Dulux premium gloss

enamel of dulux paint only. M.S Grill Gate material should be used ISI marked only.

Finishing Walls with Plastic Emulsion Paint on Wall Surfaces (Twocoats) to give an Required

shape and even shade after thoroughly brushing the surface to remove all dirt, and remains of

loose powdered materials and finishing smooth etc. complete. Rate are inclussive of Applying

Two Coats of Lappy (Putty) and One Coat of Primer on New Wall Surfaces to give an even Rs. One Hundred Eighty Five

shade including throughly brushing the surface free from mortar droppings and other foreign & Paise Forty Only

matter and sand papered smooth. (Material Shall Be Used As Per Approved Make List Of

GSPHCL.) etc. Complete for ALL FLOORS.

Finishing walls with Weather Proof Exterior Emulsion Paint on Wall Surfaces (Two Coats) over

and above Applying one coat of Primer to give an Required shape and even shade after

thoroughly brushing the surface to remove all dirt, and remains of loose powdered materials and Rs. One Hundred Fifty Five &

finishing smooth etc. complete. (Material Shall Be Used As Per Approved Make List Of Paise Twenty One Only

Providing & fixing 3mm acrylic sheet of size 60 x 15 cm with necessary screws ,plugs etc for

any Number, Writing Letter/Matter in 10cm size of radium adhesive patty or directed by Rs. One Hundred Twenty Five

engineer in charge. Only

Providing I.S.I. mark 7 levers three keys brass pad lock of Navtal (Godrej) make 75mm dia on Rs. Two Hundred Eleven &

30 completion Project.. 2.00 No. 211.86

Paise Eighty Six Only

Steel work, welded in built up sections framed work including cutting, hoisting, fixing in

position and applying a priming coat of read lead paint. (A)In beams and joists, channels angles Rs. Nine Thousand Eighteen

31 Tees, flats, with connecting plates or angle cleats as in main and cross beams. Hip and jack 21.50 Quntl 9018.30

& Paise Thirty Only

rafters, purlins conneted to common rafters and the like

providing and corrogulated JSW pre coated sheet roofing fixed withh galvanised iron J or L

Rs. Nine Hundred Eighty Four

32 hooks, bolts and Nuts 8 mm dia with bitumin and G.I. Limpet washer or G.I. limpet washer with 61.00 Sqm. 984.37

& Paise Thirty Seven Only

white lead complete excluding the cost of Purlines , rafters and trusses(0.60mm thick)

ITEM ESTIMATED RATE [Rs. Ps.] AMOUNT

DESCRIPTION OF ITEMS QUANTITY UNIT

NO. IN FIGURE IN WORDS Rs.

Providing ridges or hips 600 mm overall in plain G.I. sheet class-3 fixed with G.I.J. or L Hooks

and nuts 8mm dia G.I. Limpet and bitumen washer complete. (1) 0.80mm thick sheet. Rs. Six Hundred Fifty Eight &

Paise Twelve Only

Providing and fixing rolling shutters of approved make made of 80mm wide MS Laths

inter locked together through their entire length and jointed together at the ends by end

Rs. Three Thousand Five

likes mounted on specially designed pipe shaft with bracket plates, guide channels

34 9.00 Sqm. 3519.21 Hundred Ninteen & Paise

and arrangements for inside and outside locking with push pull operation complete including

Twenty One Only

the cost of hood cover and spring etc. complete A) shutters having width below 3.5 mt

Drilling of 300/250 mm dia pilot bore hole in all strata by using mud-flush direct rotary ring by Rs. Seven Hundred Twelve

35 using Bentonite powder. 380.00 Rmt. 712.00

Reaming 250 mm/300 mm dia pilot bore to 450 mm. dia hole including Assembling, Lowering

Housing, Casing strainer pipe, gravel packing etc.completed. From 200 mm dia to 450 mm dia Rs. Three Hundred Twenty

bore hole. Six Only

37 Conduction electrologing test of 250/300 mm dia bore hole including carting & idle-hour . 1.00 L.S. 18000.00 Rs. Eighteen Thousand Only

(A) Development of each water bearing zones comes/ across up to the full depth of tube well (

Rs. Twenty Six Thousand

size 200/250/300 mm dia. depth more than 150 meter ) by lowering 100 mm dia dropping &

38 1.00 Job 26991.00 Nine Hundred Ninety One

mm dia G.I. Airline for each zone with suitable capacity air compressor up to the availability of

sand free discharge ( Without air comp. charge)

(B) Development of above mentioned bore by air compressor 600 cfm./ 150 psi. capacity up to 6 Rs. Twenty Two Thousand

hrs minimum until sand free discharge of the above which ever is latter. 1.00 L.S. 22205.00

Two Hundred Five Only

Manufacture, supply and delivery of ISI marked ERW MS pipes conforming to IS: 4270/2001

Rs. Three Thousand Five

39 with latest amendment Rates are exclusive of GST (A) 250 MM DIA pipe (min7.10mm thick) 230.00 Rmt. 3570.00

Hundred Seventy Only

Tata or Jindal make.

Providing Supply and DILIVERY of cage type trapozodial shape V wire wound low carbon

,glavanized screen pipe and stainless steel screen pipes conforming to IS 8110 250 mm dia heavy Rs. Three Thousand Fifty

duty including 1.00 MM slot size . Eight Only

Providing & Fixing Bail plug of length 0.45 meter made from MS medium class pipe as per IS Rs. One Thousand Fifty Four

41 suitable for (C) 250 mm dia. pipe 1.00 Job 1054.48

& Paise Forty Eight Only

Water analysis charges for chemical analysis of water. Rs. One Thousand Three

Hundred Only

Providing and fixing to wall, ceiling and floor trenches blue threaded C.PVC SDR-13.5 I.S.I

mark of following in side dia. Tube fitting & clamps will all required fitting such as reducing

Rs. One Thousand Seven

coupler, Union, band plug, end cap, pipe clip, tee, hex nipple, elbow, coupler etc. complete with

43 150.00 Rmt. 1768.88 Hundred Sixty Eight & Paise

using bonding material. Rates are including of making good the wall ceiling & floor etc.

Eighty Eight Only

complete. (excavation of fearth in trenches & filling will be paid separately where ever required

(A) 80 mm dia.

Providing, installation, testing and commissioning of non-return valve of following sizes Rs. Six Thousand Nine

44 confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 80 2.00 No. 6926.77 Hundred Twenty Six & Paise

mm Dia. Seventy Seven Only

Supply of clay ball made from sticky clay of size 15 mm to 25 mm & quality certified by Rs. Seven Hundred Fifty One

Hydrologist. Only

ITEM ESTIMATED RATE [Rs. Ps.] AMOUNT

DESCRIPTION OF ITEMS QUANTITY UNIT

NO. IN FIGURE IN WORDS Rs.

Supply of Portland cement. Rs. Six Thousand Three

Hundred Two Only

Cement sealing as recommended by Hydrologist (without cost of cement) by means of mud Rs. Thirteen Thousand Two

47 pump. 1.00 Job 13273.00

Hundred Seventy Three Only

Geophysical & geohydrological ground water investigation for inalisation of one pin point Rs. Fourteen Thousand Two

48 including vehicle charges. 1.00 No 14286.00

Hundred Eighty Six Only

Clamp made from ms plate with 3 holes on either side with nuts and bolts of standerd make and Per Rs. Two Thousand Seventeen

49 suitable size g) 900 mm x 100 mmx16mm flat suitable for 250mm dia pipe. 1.00 2017.73

Pair & Paise Seventy Three Only

Bore plug of 100mm hight made from ms plate with 3 holes at equel distance on circumference Rs. One Thousand One

50 for nut -bolts type locking arragment with nuts bolts and lock nuts of standard make suitable for 1.00 No 1150.12 Hundred Fifty & Paise Twelve

250mm dia pipe. Only

Steel bent plates suitable to ERW pipe as detailed below ERW pipe 250 mm dia and size in mm Rs. Ninety & Paise Eighty

Conducting pumping test of 200 / 250 mm dia. DR tube well by submersible pump of adquate

52 capacity using DG set of required rating including providing all required tools / tackles etc. as

mentioned below for all districts.

((A) For Initial 24 hr. with sub pump 31 to 70 HP capacity LS Rs. Thirty Six Thousand Six

Job Hundred Seven Only

(B) AFTER Initial 24 Hr. Rs. One Thousand Two

Hundred Eighty Six Only

Supply of best quality well sorted Sevaliya gravel of size ranging from 4 mm to 6mm. Rs. Two Thousand Twenty

TOTAL Civil Amount B-1

54A Providing and erecting Point wiring with 1.1 KV grade ISI marked 2 X 1.5 sq. mm copper PVC

insulted FRLS wire with 1.5 sq. mm (green) copper PVC insulated FRLS wire for earth

continuity in FIA approved ISI mark medium class white colour 20/25 mm dia. embossed rigid

PVC pipe with PVC fitting fixed with adhesive solution erected on/in Wall / slab ., 5/6 Amp.

ISI make modular type switch and accessories mounted in 20 G. G.I. metallic/PVC company

fabricated box with metal grove covered with appropriate front plate modules erected flushed

Rs. Four Hundred Twenty

with wall / ceiling with necessary modular lamp holder / modular ceiling rose / HD Connector 6.00 Point 425.00

for Open wiring. Light point. Cat.-II.(make and model approved by EIC and Matching colour

with switch & accessories). Length of point wiring must not increase than 10 mtr. For that

necessary switch boards and their locations must be finalised before execution by agency

otherwise payment will not be done for extra long point. (For future extention, if required,

agency has to erect one higher size metal box and modular plate as per instruction of EIC. Cost

of blank plate shall be paid as per tender item)

54B For Fan Point (with 6 A. Modular type switch and two module hum free EME Five step type

3.00 Point 612.00 Rs. Six Hundred Twelve Only

Electronic fan regulator both having ISI mark) Cat.-II

55 Providing and erecting Medium Class FIA approved and ISI mark white colour (embossed)

RIGID PVC PIPES of following size complete erected with necessary PVC fittings & Junction

boxes fixed with adhesive solution & clamps on / in wall / ceiling along with continuous fish 15.00 Mtr. 24.00 Rs. Twenty Four Only

wire to draw mains with necessary fittings and junction boxes for following dia. (a) 20 mm. dia.

ITEM ESTIMATED RATE [Rs. Ps.] AMOUNT

DESCRIPTION OF ITEMS QUANTITY UNIT

NO. IN FIGURE IN WORDS Rs.

56A Providing and erecting Mains with FRLS PVC Insulated wire ISI marked 1.1 KV grade with

FIA approved ISI mark medium class white colour 20 mm dia. embossed rigid PVC pipe with

PVC fitting fixed with adhesive solution erected on/in brick wall / slab along with continuous G.

I. fish wire to draw mains laid in approved manner with plastering by cement mortar & finishing

the surface to match the wall / ceiling complete with FRLS PVC insulated wire for earth 10.00 Mtr. 62.00 Rs. Sixty Two Only

continuity. (Approved ISI make only) [a] 2 x 1.5 sq.mm. FRLS copper multi stranded

conductor mains with 1.5 sq.mm. FRLS copper multi stranded conductor earthing as per

standard colour code. (with 20/25 mm dia. PVC pipe)(Conductor resistance should be as per

56B 2 x 2.5 sq.mm. FRLS copper multi stranded conductor mains with 1.5 sq.mm. FRLS copper

multi stranded conductor for earthing as per standard colour code. (with 20/25 mm dia. PVC 25.00 Mtr. 82.00 Rs. Eighty Two Only

pipe) (Conductor resistance should be as per IS:8130/1984)

ITEM ESTIMATED RATE [Rs. Ps.] AMOUNT

DESCRIPTION OF ITEMS QUANTITY UNIT

NO. IN FIGURE IN WORDS Rs.

57 Providing & Erecting 2.0 mtr long Earthing system by making minimum bore of 225 mm dia

in soft soil. Suitable for doing pipe-in-pipe technology earthing.Earthing electric rod must be

made from Corrosion free Hot dip galvanizing pipes having following specification.

(A) Earthing Electrode: outerpipe:- 88 mm minimum O.D., ISI 'B ' Class ISI mark of Reputed

Brand, Inner pipe:- 42 mm minimum O.D., Pipe B Class ISI mark reputed Brand Terminal Size:

70mm X 100mm length, Terminal Should be made from inner pipe for that pipe must be pressed

and gave rectangular shape so its work as a terminal.The hot deep galvanising must be done

after above process.Galvanised thickness must be minimum 75 micron any where. SS Nut bolt:-

Rs. Seven Thousand Twenty

2 no.with washer suitable for 14mm dia. hole must be provided at terminal. total minimum 1.00 Each 7025.00

Weight(approx.) of earth electrodewith inside conductive material minimum should be 26 kg.

(B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm/meter testing as per IEC 62561-

2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%

(C) Back fill Compound:- Earthing compound should be capable to retain moisture for long time

Back Filling Compound weight is 25 Kg.

(D) Chamber and cover:- Earthing chamber should be size of 400 mm X 400 mm X 400 mm

depth and Cover should be heavy duty cast iron with required size of 300 mm X 300 mm X

Necessary test report must be submitted.

1. Short circuit test by ERDA/ CPRI for 25KA

2. Resistivity test of conducting material from NABL accredited lab.

3. Hot dip galvanised / zinc coating micro test from reputed laboratory.

4. General test report from OEM regarding specification of earthing.

[Make and model approved by EIC Strictly subject to item specification only] [OEM has to

submit all detail & sample for approved before supplying]

[Water must be poured in bore before starting earthing. Earthing value must be measured with

earth tester. Agency has to bring the earth resistance to at least 02 ohms & voltage between

neutral & Earthing upto 02 volt. Agency has to maintain earthing & its value for one year.

Earthing must be done in the presence of A.E. (GSPHCL)]

ITEM ESTIMATED RATE [Rs. Ps.] AMOUNT

DESCRIPTION OF ITEMS QUANTITY UNIT

NO. IN FIGURE IN WORDS Rs.

58 Supplying and Erecting LED indoor fitting of approximately 4 feet long with LED of wattage

0.2W to 0.5W assemble on single MCPCB with housing use as a heat sink shall be made from

Aluminum extrusion having enough strength (sample must be approved by EIC) with

polycarbonate diffuser with following specification:

(A) Company mark/name on the fitting.

(B) Rated input voltage and frequency: 220V to 240 VAC ; 50Hz.

(C) Rated input wattage: max. 24w

(D) Rated input current : 0.2 Amp

(E) Power Factor : Min.

(F) ATHD : Max. 15%

(G) Rated Luminous flux: Min. 2420 lm

(H) CCT: 6500K

(I) CRI: Min. 80Ra Rs. Three Hundred Seventy

(J) Driver Efficiency: Min. 80% Only

(K) LED life span: Min. 50000 Hrs @ L70

(L) Over Voltage protection: Withstand up to 440V/AC for 4 Hrs.

(M) Surge protection : Min. 2KV

(N) IP rating: IP

(O) IK rating : IK

(P) Short circuit , Open circuit & Reverse Polarity Protection must be provided

(Q) Fixing clamp design & strength should be sufficient to hold the fitting erected on wall or

(R) 3 core copper wire of appropriate size with earthing connector

(Note:-The manufacturer/ authorized Channel partner of the manufacturer has to submit 5 yrs

free replacement Guarantee for complete Fixture) [Approval will be given strictly subject to item

specification]

59 Providing, erecting, testing Ceiling Fan confirming to IS: 374/1979 AMDT No. 1 to 6 Class-I,

50 Hz. Specification of Ceiling Fan must be as per below. (1) Sweep: 1200 mm, (2) Operating

Voltage: 180 to 230 V, (3) Power Factor: > 0.9, (4) Power Consumption: maximum 53W, (5)

RPM: minimum 330, (6) Service value:min 4.3 m3/min. (7) Class of insulation: 'B', (8) No. of

heavy duty premium quality Ball bearing: Two, (9) Total Body: Top & Bottom should be

alluminium, (10) Blade: Aluminium approx 1.1 mm thick, (11) Colour: White high grade

powder coating, (12) Canopy: Two Nos. Heavy duty, (13) Condenser: min 1.5 MFD (15% Rs. One Thousand Nine

Tolerance )as per is 1709-1984, Aluminium body premium quality, Branded make,(14) Down Hundred Twenty Nine Only

road: up to 1.0 mtr as per site requirment, (15) Required fixing accessories, (16) 3 core

0.75 sq.mm ISI wire as per site requirment, (17) No vibration and noise due to mechanical parts.

(Agency has to erect safey wire with ceiling fan and checked with EIC) (OEM has to approved

model as per tender specification and tested at ERDA) (Necessary test reports should be

submitted strictly at the time of approval. Sample approved by EIC subject to above specification

ITEM ESTIMATED RATE [Rs. Ps.] AMOUNT

DESCRIPTION OF ITEMS QUANTITY UNIT

NO. IN FIGURE IN WORDS Rs.

60 Providing & erecting Fan clamp of 30x5 mm flat of required length & 10 mm M.S. Bolt &

Nuts erected with necessary hook of 10 mm M.S. Round Bar. 3.00 Each 98.00 Rs. Ninety Eight Only

61 Providing and erecting 240 volt MCB double pole switch for M&I(C Curve) having 10 KA

Breaking capacity and confirms to IS : 8828 in existing with earthing terminal having following Rs. Three Hundred Twenty

capacity. with necessary quarter Numbering with oil paint by Painter. (a) 40 Amp Capacity. Seven Only

62 Providing, erecting, Fabricating the M.S. structure as per requirement of site as per structure

design Including proper size approved by EIC of M.S. angles, flats, bars, square pipe, channels,

sections (Tata, Jindal, Asian, JSI Make) complete with cutting, welding, grinding and finishing

duly painted with Asian/Nerolac make premium quality oil paint and true care red oxide metal Rs. Seventy Five & Paise

primer,asian paint make with erection on site as per direction of engineer in charge with Twelve Only

necessary grouting cementing, plastering and finishing complete. All hole opening of square pipe

end must be closed with M.S plate welding. Payment will be done on KG as per Actual weight.

63 Providing and erecting Mains with ISI marked, 1.1 KV grade electrolyte multi stranded,

annealed copper conductor with heat resistant PVC insulated conforms to IS:694, IEC -

erected in existing pipe of following size (Specifically for control panel, relays, power 10.00 Mtr. 91.00 Rs. Ninety One Only

switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if

required. For One wire 10.00 sq.mm.

64 Supplying & erecting approved make SMC press moulded composite FRP. loop-in, loop-out

approx. 2mm thick box complete with Bakelite connector strip 5way(3P+N+E) & SPMCB,DIN

rail for mounting mob & hinged doors as per requirement having locking arrangements with 5.00 Each 1001.00 Rs. One Thousand One Only

mounting clamp with nuts, bolts & washers suitable for erection on pole with cable clamps&

earth bolt of following size of box.(A) 300mm x 200mm x 100mm [deep]

65 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor

for 1.1 KV. to be laid on wall with necessary clamps 1.00 mm thick to be laid 90 cms Rs. Three Hundred Sixty One

underground with 1.00 mm thick G.I heavy duty grade or in existing trench / pipe at road 120.00 Mtr. 361.00

crossing or floor of following size of cables(B) 4 core 4 Sq. mm

66 Providing & fixing Double compressed heavy duty flange type brass cable gland with rubber

ring for P V C insulated armoured cable complete with outgoing tails, insulating tape etc. For 10.00 Each 43.00 Rs. Forty Three Only

following size cables. For 2 to 4 core x 4.0 Sq. mm (Sigma, MCI, Comet, HMI Make Only)

67 Solderless crimping type Copper lugs conforming to IS suitable for cable of following size

evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium 40.00 Each 8.00 Rs. Eight Only

plated nut bolts in an approved manner.(B) For 1.5/2.5 to 6 Sq.mm Cable

68 Providing & laying HDPE Double walled corrugated pipes (DWC) (conforming to IS:

(part 24) 2018)) with minimum load required of 450N capacity with anti rodent and ultra violet

material properties with necessary connecting accessories of same material at required depth to Rs. One Hundred Seventeen

be laid 90 cms. under ground for laying of cable below ground / road surface for enclosing cable 100.00 Mtr. 117.00

and back filling the same to make ground as per original. (A) For Outer dia. 50 mm and Inner

dia. 38 mm. ) (Test Certificate to be Submitted)

ITEM ESTIMATED RATE [Rs. Ps.] AMOUNT

DESCRIPTION OF ITEMS QUANTITY UNIT

NO. IN FIGURE IN WORDS Rs.

69 SITC of Outdoor aesthetically designed LED Flood Light Luminaire with total consumption of

maximum 90 W with single piece die cast aluminium housing, LED's mounted on high quality

metal core based PCB with extremely precison designed heat sink, complete with IP66

protection Class, with polycarbonate / Toughened glass cover. The fixture should be suitable for

pole/bracket mounting. The fixture to comply both LM79 and LM 80 guidelines with LED

minimum 110 lumen/watt with L70 at 50,000 hrs, provided with high quality polycarbonate

Seperate lenses for better light distribution. The watt capacity of Each LED must be >=4W in

Rs. Six Thousand Two

street light fitting. The Fixture Should be able to be Pole Mounted and also bracket mounted, 6.00 Each 6228.00

Hundred Twenty Eight Only

provided with high quality potted driver for protection against, high and low Voltage cut Off,

opertional for high amibient and high humid envirnoments, THD of driver should be less than

10% and P.F > 0.95. Also the Fixture should meet the following technical criterias. Operating

range Voltage 160 to 270 V, system efficiency > 110 lm/w, CCT > 5000K, CRI >65, beam angle

120 deg, 4kV integral & non integral surge immunity level at least 10 KV non integral... Flood

Light lumens shall be more than 9900. (Note:- The manufacturer / authorized Channel partner

of the manufacturer has to submit 5yrs free replcement Guarantee for complete Fixture)

TOTAL Ele. Amount B-2

Total Tender Amount (Civil + Elect.work ) i.e. B1+B2 Rupees.

Executive Engineer

Signature of contractor Gujarat State Police Housing Corporation Ltd.