Const.of Wazir Ram Singh Multipurpose Sports Stadium at Nurpur Distt. Kangra (HP)

Amount

Excavation in foundation, trenches etcetera in earth work in all kind of classification of soil such as pick work, jumper work, pick jumper work. jumper blasting work , soft and hard blasting and doing work in saturated soil including chiseling or wedging out rock where blasting work is prohibited or any other mixed variety of soil including shoring, strutting dewatering and pumping or bailing out water ( surface and sub soil water ) upto any depth or any quantum of water including slush which may arise during dewatering removal of slush and stacking the serviceable and unserviceable material clear from the edges of excavation as directed by the Engineer-in-charge and then returning the stacked soil in 15 cm ( fifteen centimeters ) layers when required into plinths and sides of foundation etcetera consolidating each deposited layer by ramming and watering and then disposing of all surplus unserviceable excavated earth as directed by Engineer in charge within all leads and lifts disposed earth to be levelled and neatly dressed including carriage of materials within all leads, lifts and other incidental charges. The rate is inclusive of octroi, royality, malkana, toll tax, G S T, and other taxes imposed by the government.

Providing/ fixing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, height of propping and centering in all heights / depth below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in foundation footings, basis of columns etcetera and mass concrete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government

Providing and fixing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights / depth below supporting floor to ceiling up to any height and removal of the same for in situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors, roofs, landings , shelves and the like floor etcetera upto any thickness upto all floor level including carriage of materials within all leads , lifts and other incidental as per approved drawings, design and as per directions by the Engineer in charge. The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and fixing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights/ depth below supporting floor to ceiling upto any height and removal of the same for in situ reinforced concrete and plain concrete work in Columns, pillars abutnents, post and struts (square rectangular or polygonal in plan in any heights / thickness/depths etcetera upto all foor level including carriage of materials within all leads , lifts and other incidental and as per approved drawings, design and as per directions by the Engineer in charge. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights / depths below supporting floor to ceiling upto any height and removal of the same for in situ reinforced concrete and plain concrete work in lintels, beams, plinth beams, girders, bressumers and cantilevers etcetera upto all floor level including carriage of materials within all leads , lifts and other incidental as per approved drawings, design and as per directions by the Engineer in charge. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government .

Providing and fixing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights / depths below supporting floor to ceiling upto any height/ depths and removal of the same for in situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls of any width etcetera upto all floor level including carriage of materials within all leads and lifts and other incidental as per approved drawings, design and as per directions by the Engineer in charge. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government .

Providing and fixing form work with steel plates 3.15mm(three point one five millimeters)thick welded with angle iron in frame 30x30x5mm(thirty into thirty into five millimeters),so as to give a fair finish including centering ,shuttering, strutting and propping etcetera with wooden battens and ballies, height of propping and centering in all heights / depths below supporting floor to ceiling upto any height and removal of the same for in situ reinforced concrete and plain concrete work in stair cases with sloping or stepped soffits excluding landing upto all floor level as per approved drawings, design and as per directions by the Engineer in charge. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government . including carriage of materials within all leads , lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Stone filling under floor complete as directed by the Engineer-in Charge including carriage of materials within all leads , lifts and other incidental charges. The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Filling in plinth with sand under floor including watering, ramming consolidating and dressing complete as per HP.PWD. specifications or as directed by the Engineer-in Charge including carriage of materials within all leads , lifts and other incidental charges. The rate is including of octroi , royalty , Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and laying cement concrete 1:4:8 (one cement; four sand : eight graded broken /crushed stone aggregate 40mm(forty millimeters) nominal size vibrated and mechanically mixed and curing complete excluding the cost of centering and shuttering in all work upto plinth level and as per approved drawing ,design as per directions of Engineer in charge including carriage of materials within all leads , lifts and other incidentals The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and laying in position machine batched and machine mixed design mix M-20 (M-twenty ) grade to obtain the minimum compressive strength of 20 N/mm² (twenty newton per square milimeters)with cement contents not less than 330 kg (three hundred thirty kilogramme) per cubic meter and curing complete excluding cost of reinforcement for reinforced concrete work as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability for all works upto plinth level as per approved drawings , design, and as per direction of Engineer-in-charge. including carriage of materials within all leads , lifts and other incidentials. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and laying in position machine batched and machine mixed design mix M-20 (M-twenty ) grade to obtain the minimum compressive strength of 20 N/mm² (twenty newton per square milimeters)with cement contents not less than 320 kg (three hundred twenty kilogram) per cubic meter and curing complete excluding cost of reinforcement for reinforced concrete work as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability for all work above plinth level to all floor level as per direction of Engineer-in-charge including carriage of materials within all leads , lifts and other incidentals. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and laying cement concrete 1:3:6 (one cement; three sand : six graded broken /crushed stone aggregate 40mm(forty millimeters) nominal size vibrated and mechanically mixed and curing complete excluding the cost of centering and shuttering in all work upto plinth level and as per approved drawing ,design as per directions of Engineer in charge including carriage of materials within all leads , lifts and other incidentals The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and laying cement concrete 1:2:4 (one cement; two sand : four graded broken /crushed stone aggregate 40mm(forty millimeters) nominal size vibrated and mechanically mixed and curing complete excluding the cost of centering and shuttering in all work upto plinth level and as per approved drawing ,design as per directions of Engineer in charge including carriage of materials within all leads , lifts and other incidentals The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and fixing Steel reinforcement of Tata/ Tiscon / Sail Thermo-Mechanically Treated bars of grade Fe-500 (D ) for reinforcement cement concrete work including straightening, cutting, bending, placing in position and binding all complete for all floors level including carriage of materials within all leads , lifts and other incidentials.. The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Brick work using Second class common burnt clay buildings bricks in super-structure above plinth level to all floor level in cement mortar 1:6 (one cement : six sand) and curing complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Second class half brick masonry in common burnt clay building bricks in super- structure above plinth level upto all floor level in cement mortar 1:4 (One Cement : four sand ) and curing complete as per approved drawings design and specifications and direction of Engineer in charge including carriage of material within all leads, lifts and other incidentals The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

6mm (six millimeter)thick cement plaster in ceiling with cement mortar 1:3(one cement; three sand) upto all floor level and curing complete as per approved drawings, design and as directed by the Engineer in charge including carriage of materials with in all leads and lifts and other incidental The rate is including Royality, Malkana, Octroi, Toll Tax, GST or any other taxes imposed by the Government.

Providing and applying 15mm (fifteen millimeters) thick cement plaster with cement mortar 1:6 (one cement isto six sand) in single coat on fair side of brick/concrete/ stone walls for interior plastering up to all floor level including arises, internal rounded angles, chamfers and/or rounded angles in all girth and finished even and smooth complete as per approved drawing, design specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and applying 15mm (fifteen millimeter) thick cement plaster with cement mortar 1:6 (one cement isto six sand) in single coat on rough side of brick/concrete/ stone walls for plastering up to all floor level including arises, internal rounded angles, chamfers and/or rounded angles in all girth and finished even and smooth as per approved drawing, design and specifications as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and applying Birla white / J.K. cement based putty of average thickness 1 mm, (one millimeters ) of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per approved drawings, design specifications and directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government

Distempering (two or more coats ) with first quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre( fifty grams per litres ) of approved manufacturer of Asian/ Nerolac , of required shade and colour complete, as per specification of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Finishing walls ( Two or more coats ) with weather proof emulsion paint of Nerolac/ Asian applied at the rate 3.84 kg (three point eight four kilogram) per 10 sqm.(ten square metre ) over the plastered wall surface to prepare the surface even and smooth complete as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying 52mm (fifty millimeters) thick Cement concrete flooring 1:2:4 (one cement; two sand; four graded broken/ crushed stone aggregate 20mm (twenty millimeters) nominal size ) laid in one layer finished with a floating coat of neat cement upto all floor level and curing complete and as per approved drawings, design, specifications and as directed by the Engineer in charge including carriage of materials with in all leads, lift and other incidental. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and laying 600x600mm (six hundred into six hundred millimeters ) in size of specific thickness Double charged vitrified tiles of Restile / Nitco / Simpolo / Orient -Bell / Rak/ Kajaria /AGL/Johnson in grey/coloured or of approved shade and design in flooring, treads of steps and landing laid on a bed of 12mm ( twelve millimeters ) thick cement mortar 1:3 (one cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per approved drawings deign and specifications and as directed by Engineer in charge including carriage of materials within all leads , lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government .

Providing and laying 300x450mm ( three hundred into four hundred fifty millimeter ) of specific thickness anti skid Ceramic glazed tiles of Kajaria /Swastik/ Sommany/ Bell / AGL with one border matching contrast at Top in flooring over 12 mm (twelve millimeter ) thick bed of cement mortar 1:3 (one cement : three coarse sand) and jointing with neat cement slurry , finished with flush pointing in white cement mixed with pigment of required shade to match shade of tiles complete as per approved drawings, design and specifications and as directed by the Engineer in charge including carriage of materials within all leads , lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and laying Ceramic glazed tiles of size 300x450mm ( three hundred into four hundred fifty millimeter ) size of specific thickness (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown in skirting and dado laid on 20 mm thick cement mortar 1:4 (one Cement : four Coarse sand), Jointing with grey cement slurry at the rate 3.30 kg/sqm ( three point three zero kilogram square meter ) including pointing the joints with white cement and matching pigment etcetera complete as per approved drawing, design specification and as per directions of Engineer-in- charge including carriage of materials within all leads, lifts and other incidentals. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and Laying Kota stone one single slabs having semi rounding 20 mm ( twenty millimeters ) thick in risers of steps, skirting, dado and pillars laid on 12 mm ( twelve millimeters ) (average) thick cement mortar 1:3 (one cement: three coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete in all floor / heights as per approved drawings, design, specifications and directions by the Engineer in charge including carriage of materials within all leads , lift and other incidental . The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and laying Labrador Series in Ramp 40mm (forty millimeters) average thick on 20mm average thick base of cement mortar 1:4 ( one cement : four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polish finish complete including rubbing and polishing complete as per approved drawings, design, specifications and as per directions of Engineer-in- charge including carriage of materials within all leads, lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and fixing prepainted (ISI marked -Z 120) of tata /Durashine/ Reliance/ Jindal steel sheet roofing over all steel trusses providing and fixing prepainted single skin trapazodial profile sheething 0.60mm (Zero point sixty millimetre) thick having (1060 mm (one thousand sixty millimeters ) cover with overall width 1126 mm)( one thousand one hundred twenty six millimeters ) 28 mm (twenty eight millimeters ) crest depth at 353. I 2 centre to centre crest distance there will be two ribs at the centre or stiffning having depth of 25mm (Twenty five millimeter) at the lower 81mm (Eighty one millimeter) base metal of cold rolled steel coil with zink coating top coat with regular modified polyster coating of 20 (Twenty) micron over 5 (Five) micron primer coating to back coat of palyster of 5 (Five) micron over 5 (Five) micron primer approved shade and Balancing reverse coat with polyster paint fixing of sheet shall be with self drilling and self tapping screws, of size 5.5mm (Five point five millimeter) diameter 75.5mm (Seventy five point five millimeter) length with EDPM seal. The material supply will be accompanied by test certificate and against corrosion/ Fading of colour and manufacturing defects etcetera and further as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing prepainted (ISI marked -Z 120) of tata , Durashine /Reliance/ Jindal steel sheet ridges or hips 60cm (Sixty centimetre) overall 0.60mm (Zero point sixty millimetre) thick having proper Gola of steel sheet Shape metal with hot dipped metallic zink coated with top coat with regular modified polyster coating of 20 (Twenty) micron over 5 (Five) micron primer coating to back coat of polyster of 5 (Five) micron over 5 (Five) micron primer of approved shade and Balancing reverse coat with polyster paint including fixing of sheet with prepainted self drilling and self tapping screws, of size 5.5mm (Five point five millimeter) diameter and 55mm ( fifty five millimeter) length with EDPM seal .The material supply will be accompained by test certificate against corrosion/ Fading of colour and manufacturing defects as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 0.60mm ( zero point six zero millimeters ) thick plain galvanized iron sheet 30cm ( thirty centimeters ) wide 25 cm ( twenty five centimeters ) deep overall semi circular plain galvanized iron sheet gutter of TATA , SHAKTI. Reliance, Jindal jointed with and fixing with bolts , nuts and washer etc. complete including making necessary connections with rain water pipe complete as per drawing specifications , design and specification including carriage of materials within all leads , lifts other incidential. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing mild steel black plain sheet of Tata, Reliance, Jindal Sail 2.00mm (two point zero zero millimeter) thick in facia/eaves boards/soffits /ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Structural steel of Tata/ Sail work bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete in trusses and trussed purlins, main and cross beams, hip and jack rafters, purlins connected to common rafters and the like in building including cutting, fixing, lifting, hoisting and placing in position complete and applying a priming coat of red lead paint complete as per approved drawings, design specifications as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is inclusive of Royality, Malkhana, Octroi, Toll Tax G S T or any other taxes imposed by the Government

Supplying and fixing rolling shutters of approved make, made of 80x1.20 mm (eighty into one point two zero millimeter ) mild steel laths with 1.20 mm (one point two zero millimeters ) thick top cover interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm (twenty seven point five centimeter ) long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 complete as per approved drawings, design specifications and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Royality, Malkhana, Octroi, Toll Tax G S T or any other taxes imposed by the Government.

Providing and fixing moulded hand rail of Mild steel hollow pipe 50mm dia (fifty millimeters dia meters ) welded in straight length over Mild steel flat size 50x5mm at top of vertical balusters of size 25mm dia including one coat of red oxide priming coat complete and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is inclusive of Royality, Malkhana, Octroi, Toll Tax G S T or any other taxes imposed by the Government.

Providing and fixing factory made P.V.C. door frame of Rajshri/ Supreme/ Prominence size 50x47 mm ( fifty into forty seven millimeters ) with a wall thickness of 5 mm,(five millimeters ) made out of extruded 5mm (five millimeter ) rigid PVC foam sheet, mitred at corners and joined with 2 two ) Nos of 150 mm (one hundred fifty millimeter ) long brackets of 15x15 mm ( fifteen into fifteen millimeters ) Mild steel square tube, the vertical door frame profiles to be reinforced with 19x19 mm ( nineteen into nineteen millimeters ) Mild steel square tube of 19 ( nineteen ) gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using mild steel screws of 65/100 mm( sixty five oblique hundred size, complete as per approved drawings, design specifications and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is inclusive of Royality, Malkhana, Octroi, Toll Tax G S T or any other taxes imposed by the Government.

Providing and fixing standard steel doors frame for doors, manufactured from M.S .angle iron section of 35x35x5mm / 40x40x5mm ( thirty five into thirty five into five millimeters/ forty into forty into five millimeter) of Tata, Sail and M.S. 35x5mm (thirty five into five millimeter ) flat pieces to the existing T-iron frame or to the wall with dash fastner including fixing of necessary butt hinges 2.5mm ( two point five millimeters ) thick with provision for locking arrangement and shock observers as specified and applying a coat of approved steel primer after pretreatment of the surfaces as directed by the Engineer-in-Charge as per approved drawings, design specifications including carriage of materials within all leads, lifts and other incidental. The rate is inclusive of Royality, Malkhana, Octroi, Toll Tax G S T or any other taxes imposed by the Government. .

Providing and fixing steel glazed doors,windows and ventilators of standerd rolled steel sections ,joints mitred and welded with 16x3.15 mm ( sixteen into three point onefive millimeters ) lugs 10 cm (ten centimeter ) .long embedded in cement concrete blocks 15 cmx10cmx10cm ( fifteen centimeter into ten centimeters into ten centimeters ) size of 1:3:6( one cement: three sand: six graded stone aggregate 20mm (twelve ) nominal size)or with wooden plugs and screws or rawl plug and screws or with fixing clips or with bolts and nuts as required and iron fittings,including providing and fixing of 5mm (five millimeters )thick glass panes of Modi Guard, Saint Gabin with glazing clips and special metal sash putty of approved make complete for side hung windows including applying a priming coat of red lead paint as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is inclusive of Royality, Malkhana, Octroi, Toll Tax G S T or any other taxes imposed by the Government. .

Providing and fixing factory made panel PVC door shutter of Rajshri, Supremo, Prominence consisting of frame made out of M.S. tubes of 19 (nineteen ) gauge thickness and size of 19 mm x 19 mm (nineteen millimeters into nineteen millimeters ) for styles and 15x15 mm (fifteen into fifteen millimeters ) for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm ( thirty millimeters ) thickness, 70 mm ( seventy millimeters ) width out of which 50 mm (fifty millimeter ) shall be flat and 20 mm ( twenty millimeter ) shall be tapered in 45(forty five ) degree angle on both side forming styles and 5 mm (five millimeter ) thick, 95 mm ( ninety five millimeter ) wide PVC sheet out of which 75mm shall be flat and 20 mm ( twenty millimeter ) shall be tapered in 45 (forty five ) degree on the inner side to form top and bottom rail and 115 mm (one hundred fifteen millimeter ) wide PVC sheet out of which 75 mm ( seventy five millimeter ) shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top , bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 )thick, 20 mm ( twenty millimeter ) wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm (fifteen millimeter ) wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm (five millimeter ) thick PVC strip of 20 mm ( twent millimeter ) width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification and drawing.30 mm (thirty millimeter ) thick pre laminated PVC door as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is inclusive of Royality, Malkhana, Octroi, Toll Tax G S T or any other taxes imposed by the Government.

Supplying and fixing 4 mm (four millimeter ) thick frosted glass panes of modi guard / Sanit gobain with putty and nails complete and as directed by Engineer in charge including carriage of materials within all leads, lifts and other incidental. The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and fixing 150 mm( one hundred fifty millimeter) dia on wall face PVC (D-Plast) rain water pipes of working pressure 4.5 kg ( four point five kilogram) ISI mark of Finolex / Relpipe ( Reliance) / Vectus / Supremo including filling the joints with approved adhesive complete as per approved drawings, design specifications and direction of Engineer in charge including carriage of material within all leads, lifts and other incidentals The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 150 mm( one hundred fifty millimeters) PVC plain bend of Finolex, Relpipe, Relinace, Vectus / Supremo on wall face PVC accessories for rain water pipes complete as irected by the Engineer in charge including carriage of material within all leads, lifts and other incidentals The rate is inclusive of octroi, royality, malkhana, toll tax, GST or any other taxes imposed by the Government.

Applying priming coat (two or more coats ) over new wood and wood based surfaces after and including preparing the surfaces by thoroughly cleaning oil, grease dirt and other foreign matter sand papering and knotting with ready mixed pink or grey primer of asian/ Nerolac paint brushing wood primer pink as per approved specification, drawings, design and as directed by the Engineer in charge including carriage of materials within all leads, lifts and other incidental. The rate is including Royality, Malkana, Octroi, Toll Tax, GST or any other taxes imposed by the Government

Painting two or more coats (excluding priming coat) on new wood and other wood surfaces with Deluxe Multi Surface Paint of Asian/ Nerolac required shade at the rate of 0.90 ltr/10 sqm ( zero pint nine zero litre per ten square meter ) over an under coat of primer applied at the rate of 0.75 ltr/10 sqm ( zero point seven five litres per ten square meter ) brushing to give an even shade including cleaning the surfaces of all dirt dust and other foreign matter and as per approved drawings, design specifications and as directed by the Engineer in charge including carriage of materials within all leads and lifts and other incidental. The rate is including Royality, Malkana, Octroi, Toll Tax, GST or any other taxes imposed by the Government

Painting two or more coats on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surfaces of all dirt dust and other foreign matter with Asian/ Nerolac / deluxe multi surface paint other than white and as per approved drawings, design specifications and as directed by the Engineer in charge including carriage of materials within all leads and lifts and other incidental. The rate is including Royality, Malkana, Octroi, Toll Tax, GST or any other taxes imposed by the Government

Providing and fixing 250 X 16 mm ( two hundred fifty into sixteen millimeters ) Coloured anodized aluminum sliding door bolts, ISI marked anodized (anodic coating not less than grade AC 10(ten ) as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etcetera complete as per specifications and as directed by Engineer in charge including carriage of materials within all leads lifts and other incidental . The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government :

Providing and fixing 250x 10 mm ( two hundred fifty into ten millimeters ) Coloured anodized aluminum tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 (ten ) as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete as per specification and as directed by Engineer in charge including carriage of materials within all leads lifts and other incidental . The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and fixing 100mm (one hundred millimeter ) Coloured anodized aluminum handles, ISI marked, anodized (anodic coating not less than grade AC 10 (ten ) as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete as per specifications and as directed by Engineer in charge including carriage of materials within all leads lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and fixing 250 X 16 mm ( two hundred fifty into sixteen millimeters ) mild steel sliding door bolts, ISI marked with nuts and screws etc. complete as per specifications and as directed by Engineer in charge including carriage of materials within all leads lifts and other incidental . The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government :

Providing and fixing 200x 10 mm ( two hundred into ten millimeters ) mild steel tower bolts, ISI marked with necessary screws etc. complete as per specifications and as directed by Engineer in charge including carriage of materials within all leads lifts and other incidental . The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government .

Providing and fixing 100mm (one hundred millimeters ) mild steel handles, ISI marked, with necessary screws etc. complete and as directed by Engineer in charge including carriage of materials within all leads lifts and other incidental. The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and fixing polytheline aluminum polythylene (PE-AL-PE) composite pressure pipe U.V.stabilized with carbon black confrming to IS- 15450-2004 of kitec or its equivalent for water supply including clamp at one metre spacing cutting fixing and making good the wall etcetera but excluding the cost of fittings (internal work ) pipes exposed on wall internal work Exposed on wall 1620 (one thousand six hundred twenty)(20 mm OD ( twenty millimeters outer dia meter ) pipe as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and fixing polytheline aluminum polythylene (PE-AL-PE) composite pressure pipe U.V.stabilized with carbon black confirming to IS- 15450-2004 of kitec or its equivalent water supply including clamp at one metre spacing cutting fixing and making good the wall etcetera but excluding the cost of fittings (internal work ) pipes exposed on wall internal work Exposed on wall 2025 (two thousand twenty five hundred (25 mm OD ( twenty five millimeters outer dia meter ) pipe as per specifications directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and fixing 110 mm( one hundred ten millimeter ) dia meter pipe of on wall face unplasticised - PVC soil waste and ventilating pipe of Finolex/ Relpile. (Reliance/ Vectus / Supremo conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimeter ) gap for thermal expansion as per specifications and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and fixing 110 mm dia ( one hundred ten millimeter dia meter ) bend Finolex/ Relpile. (Reliance/ Vectus / Supremo on wall face unplasticised - PVC soil waste ventilating pipe fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and fixing 110 mm dia ( one hundred ten millimeter dia millimeter) shoe Finolex/ Relpile. (Reliance/ Vectus / Supremo on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes soil water ventilating pipe conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion as per specifications and directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and fixing 110 x 90 mm ( one hundred ten into ninety millimeters ) nominal size/diameter P.V.C. floor trap Finolex / Relpipe (Reliance) /Vectus ISI marked Confirming to BIS-14735-99 of self cleaning design including fixing with approved adhesive , cost of cutting and making good the wall and floor etc complete. as per specifications directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and fixing white vitreous china pedestal type water closet (European type)No 20092 size 61.5 x 34.5 x 40 cm ( sixty one point five into thirty four point five into forty centimeters ) with seat and lid, 10 (ten ) litre low level white vitreous china flushing cistern (sleek plus) of Cera / Hindware / Jaquar of star white / snow white shade and chromium plated flush bend with fittings and cast iron brackets, 40 (forty millimeter ) mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling as per approved drawings, design and specifications complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :Water Closet pan with ISI marked white solid plastic seat and lid complete as per specifications and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm ( five hundred eighty into three hundred eighty into three hundred fifty millimeter ) with white Single half stall urinal with 5 ( five ) litre P.V.C. automatic flushing cistern of cera, Hindware, Jaquar of star white / snow white shade , with fittings, standard size chromium plated brass flush pipe, spreaders with unions and clamps chromium plated brass with waste fitting as per IS : 2556, cast iron trap with outlet grating and other couplings, including painting of fittings and cutting and making good the walls and floors wherever required as per specifications directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and fixing wash basin White Vitreous China Flat back size 550x 400 mm ( five hundred fifty into four hundred millimeters ) (under counter basins) of Cera / Hindware / Jaquar of star white / snow white shade with single 15 mm (fifteen millimeter ) chromium plated brass pillar tap with 32 mm (thirty two millimeter ) brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required as per specifications directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and fixing 32 mm (thirty two millimeters)diameter P V C waste pipe continental series of jaquar/Contess plus series of Hindware /Ocean Series of Cera /Hindon series of JAl / vintage series of kerovite for wash basin and sink complete as per specifications and as per directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals . The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and fixing 600mm x 450mm (six hundred millimeters into four hundred fifty millimeters) beveled edge mirror of superior glass of Modiguard/ Saint Gabine Silver fish mounted on 6mm ( six millimeters) thick asbestos cement sheet or ply wood sheet and fixed to wooden plugs with chromium plated Brass screws and washers complete as per specifications and directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals . The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and fixing 15 mm ( fifteen millimeter ) nominal bore chromium plated brass bib cock tap continental series of jaquar/Contess plus series of Hindware /Ocean Series of Cera /Hindon Series of Jal / vintage series of kerovite of approved quality conforming to IS:8931 as per specifications directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and fixing 15 mm ( fifteen millimeter ) nominal bore chromium plated brass angle valve of continental series of Jaquar/continental series of Hindware/ Occian series of Hindware series of Jal/ vintage series of kerovite for basin mixture and gyster point of approved quality conforming to IS 8931 of standard design and of approved make as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals The rate is including G S T, Toll tax or any other taxes imposed by the Government.

Providing and fixing circular type 100mm (One hundred millimetres) diametres chromium plated Grating of continental series of Jaquar/continental series of Hindware/ Hindun series of Hindware / series of Jal/ vintage series of kerovite approved quality and colour for gully floor or Nahni trap as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals . The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and fixing 15mm ( fifteen millimeter ) nominal bore unplasticised PVC connection pipe with brass union 45cm ( forty five centimeters ) length complete as per specifications and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and placing on terrace polyethylene water storage tank cylindrical shape of Finlex / vectus / Relastic/ Reliance ) / Supremo/ Sintex ( ISI :12701 marked / Treepal layer ) universal or equivalent make ) including and P.V.C.( poly vinyl chloride) mosquito proof cover with locking arrangement and making necessary holes for inlet/ out let and over flow pipe but without fittings and the base support for tank. in all floor level / heights as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and fixing 15 mm ( fifteen millimeter ) nominal bore chromium plated brass ball valve of continental series of Jaquar/continental series of Hindware/ Occian series of Hindware / Hundun series of Jal/ vintage series of kerovite of approved quality high and low pressure with plastic floats including fitting complete as per specifications and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals . The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and fixing 20 mm ( fifteen millimeter ) nominal bore chromium plated brass ball valve of continental series of Jaquar/continental series of Hindware/ Occian series of Hindware series of Jal/ vintage series of kerovite approved quality high and low pressure with plastic floats including fitting complete as per specifications directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals . The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and fixing white vitreous china pedestal of Hindware/ Cera/ Jaquar of Stair white / snow white shade for wash basin completely recessed at the back for the reception of pipes and fittings as per specifications and directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals . The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government..

Providing and fixing 15 mm ( fifteen millimeter ) nominal bore chromium plated brass stop cock (concealed) of standard design of contigental series of Jaquar/ contess series of Hindware/ ocean series of Cera/ Kindon series of Jal/ vintage series of kerovite and of approved make conforming to IS:8931 as per specifications and directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals The rate including G S T. Toll tax or any other taxes imposed by the Government.

Providing and fixing 15 mm ( fifteen millimeter ) nominal bore chromium plated brass pillar tapwith capstan head of continental series of jaquar/Classic series of Hindware /floral Series of Cera /Hindon Series of Jal of standard design and of approved drawing as per specifications and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals . The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and fixing 600x120mm x 5 mm ( six hundred into one hundred twenty millimeters into five millimeters ) glass shelf with edges round-off supported on anodized aluminum angle frame continental series of jaquar/Contessa plus series of Hindware with chromium plated brass bracket and guard rail complete fixed with 40mm ( forty millimeters screws/ rawl plugs and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals . The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and laying of 150 mm (one hundred fifty millimeter) internal dia meter P V C of Finolex/ Relpipe ( Reliance/ Vectus / Supremo pipe grade- A (to level or slope) and jointing with approved adhesive complete including testing of pipes and joints complete as per specifications as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10(one cement; five : sand ten graded /crushed stone aggregate 40mm(forty millimeter) nominal size bedding for P V C pipe of 150mm (one hundred fifty millimeter) internal diameter including necessary form work as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals . The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and fixing accessories for P V C pipe grade- A that is 150mm (one hundred fifty millimeters)dia P.V.C. plain bend Finolex/ Relpipe ( Reliance/ Vectus / Supremo of approved quality including jointing with approved adhesive as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals . The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and fixing accessories for P V C pipe grade- A that is 150mm (one hundred fifty millimeters)dia P.V.C. Collar of Finolex/ Relpipe ( Reliance/ Vectus / Supremo approved quality including jointing with approved adhesive as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals . The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government

Providing and fixing 600x 300 ( six hundred into three hundred millimeter ) vitreous china Division plate for urinals of Cera / Hindware / Jaquar of star white / snow white with integral rim longitudinal flush pipe as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals . The rate is including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and fixing 110mm (one hundred ten millimeters)dia P.V.C. Finolex / Relpipe (Reliance) /Vectus heal rest sanitary bend including filling the joints with approved adhesive. as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Providing and fixing 100mm (one hundred millimeters)dia for P V C clamps of approved design of Finolex/ Relpipe ( Reliance/ Vectus / Supremo to P V C pipes embeded in and including cement concrete block 10x10x10cm (ten into ten into ten centimeters) of 1:2: 4 (one cement; two sand four graded /crushed stone aggregate 20mm (Twenty millimeters)nominal size) mix and cost of cutting holes and making good the wall. complete as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate including of octroi, royality, Malkana, toll tax, G S T or other taxes imposed by the Government.

Nishchal Mahajan

sourav mahajan

MM Envro Engineers