Office Partition Works at IBP-M

Amount

Demolishing of brick work

Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

Unskilled Labour charges

Miscellaneous Labours

Demolishing RCC Work

Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

Dismantiling doors and windows

Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats,architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below

Dismantiling of Tile Work

Dismantling tile work in floors laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

Centering and shuttering

Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams,girders bressumers and cantilevers

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size). Cement supplied by KMML.

Red earth filling

Supplying & filling with red earth, spreading in layers, leveling the top at site and consolidation by plate compactor, ramming etc complete as per the instruction of Engineer in charge. Measurement will be taken for the compacted volume only.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level: 1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size Required cement shall be supplied by KMML

Reinforcement steel work

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo - Mechanically Treated bars of grade Fe-500D or more.TMT bars supplied by KMML

Masonry work

Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete(Cement supplied by KMML)

Plastering

Plastering with 12 mm cement plaster of mix:<br>1:4 ( 1 cement : 4 fine sand)(The required cement shall be supplied by KMML at our store)

GI-Steel work

Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.of approved make) in trusses etc , including cutting, hoisting,fixing in position and applying a priming coat of approved epoxy primer and 2 or more coats of epoxy paint, including welding and bolted with special shaped washers etc. complete

Cement board work

Providing and fixing Cement board (High Pressure steam cured) as per IS : 14862, with suitable screws etc. complete (frame work to be paid separately) : 8 mm thick cement board

False ceiling

Providing and fixing stepped false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flanged of cleat fixed to the angle hangers of 25x10x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45x15x0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5 mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flages of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of day wall screws of size 3.5x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes, finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitable fixed, all complete as per drawings, specification and direction of the Engineer in charge but excluding the cost of painting with. 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through acutoclaving process.

Floor tile

Supply and laying first quality vitrified digital tiles of size 1200 x 600mm of approved make like Kajaria/Cera/johnson/somany/NITCO or other approved brand in approved shade and pattern for floors as per architectural design laid on 20mm thick cement mortar 1:4 (1 cement : 4 course sand ) with tile spacer and jointing with with epoxy joint fillers minimum of 5mm thick of matching shades of approved brand, complete. (The required OPC cement shall be supplied by KMML at our store).

Tile Skirting

Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with epoxy joint fillers & matching pigments etc. complete. Size of Tile 1200x600 mm(Cement shall be supplied by KMML)

Wood frame work for doors and windows

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Mahagany/ Anjali wood.

Wood shutters for door and windows

Providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer in charge. using Mahogany.

wood panels for doors and windows

Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel excluding portion inside grooves or rebates to be measured) paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality Mahogany

M.S Grill for Aluminum windows

Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved epoxy primer and 2 coats of epoxy paint all complete. Fixed to steel windows by welding

Hold fast

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3coarse sand : 6 graded stone aggregate 20 mm nominal size)

Tower bolts

Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:200x10 mm

Wood polishing

Melamine polishing on wood work (one or more coat) including all base preparations like application of sealers , fillers, cost of all materials etc.

Aluminum frame work

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS :733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

Aluminum shutter work

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron) Specifactions same of above item.

Glazing in aluminum work

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer -in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

Lock for doors

Providing and fixing 100 mm brass locks ( best make of approved quality ) for aluminium doors including necessary cutting and making good etc. complete

Multi wood board for aluminum door

Providing and fixing Thomson Multi wood board or equivalent make paneling 12 mm thick, to frame,backing or studding with screws etc. complete ( Frames, backing or studding to be paid separately) as per the direction of site Engineer-in-charge.

Seet Roofing

"Fixing FRP/poly carbonate/PVC /metallic sheets upto any pitch in horizontal /vertical / curved surfaces and fixing with polymer coated J, or L hooks, bolts and nuts 8mm dia. G.I. plain and bitumen washers or sheets shall be fixed using self drilling / self tapping screw of size (5.5X55mm) with EPDM seal complete , but excluding the cost of purlins, rafters, trusses, and including cutting to size and shapes where ever required. etc. complete (excluding cost of sheet, purlins, rafters and trusses (The required sheet and fixtures shall be supplied by the company) including shifting, lifting,cutting sheets to size and shape wherever required,all tools,tackles, labours, scaffolding etc. For level upto 10m from GL"

Half partition work-wooden

Fabricating and Fixing at site half partition (double skinned ) of height approx. 1200 mm and width 75mm to form seperation between worktops or cabins. A frame work of height 120 cm is made using 19 mm Marine plywood sections with grid of average spacing 60cm x 60 cm in between vertical or horizontal members frame work is screwed on to floor/wall using steel screws of suitable size. Necessary cuttings in frames is to be provided to draw cable conduits. 9 mm thick Marine ply wood or flexy plywood is fixed on to both sides of the frame work with joints perfectly finished without any projections at joints. 1 mm thick laminate as specified in the list of approved brands is pasted on both sides as per the detail specification in drawing. 15mmx 80mm decorative beech wood/pine wood/teak wood or equivalent wooden beeding or liping is fixed over top and cut edges. Necessary grooves, cuttings and inlays should be given as per drawings. Cuttings for fixing electrical boxes/switches should be provided where ever necessary. A skirting is fixed on to it at floor level as per details. All exposed wooden surfaces are polished with melamine matt/clear after applying necessary base preparations, including concealing the screw heads. cost of skirting and polishing will be separate item (Refer Dwg. A-01)

Full partition work-Gypsum board

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction ofengineer in charge all complete.75 mm overall thickness partition with 12.5 mm thick double skin taperededged plain Gypsum board conforming to IS : 2095 : part I

Work top

Fabricating and fixing at site, work top made of 19mm thick MPW with laminated top with average lenght 90cm to 105cm and width 60cm with independent supports and cut edges finished with 2mm edge bending tapes and provided with a key board drawer, CPU stand and foot rest . The work tops are provided with wire manager systems .The rate should include all related hardwares and labour. Refer Drg. No.A-03

Wall paneling

Fabricating and fixing at site wall paneling of height 1200mm on frame work of height 120cm is made using 19mm marine ply wood sections with grid of average spacing 60cm x 60cm in vertical and or horizontal screwed on to wall using steel screws of suitable size. 9mm tk marine plywood/flexy plywood is fixed on to the frame work with joints perfectly finished without any projections at joints. 1mm tk laminate as specified in list of approved brands is pasted as per the detail specification in drawing . 15mm x 85mm or matching size Beech wooden/pine wood/teak wood beeding is fixed over top and at cut edges. Necessary grooves, cuttings and inlays should be given as per drawings. A skirting is fixed on to it at floor level as per detail . All exposed wooden surfaces are polished with melamine matt /clear after applying necessary base preparations, including concealing the screwheads Cost of skirting and polishing will be a separate item.

Wooden skirting

Fabricating and fixing at site on to wall / paneled wall/ partition or counters at base a beechwood/pine wood/teak wooden skirting of size 75mm x 6mm with top detailed as per drawing and fixed on to wall or partition base using suitable size brass screws or headless brass nails and along with glue. The joints of the skirtings should be neat and no visible difference or overlaps should be seen. The surface is polished with melamine semi gloss after preliminary preparation of the surface.

Side table

Fabricating and supplying at site, side table for the main counters made of 19 mm thick laminated MPW [BWP Grade] IS: 710 boxing as shown in drawing. The shutters, shelves shall be of 18 mm thick MPW laminate and drawers fixed on SS drawer channels, as per the size specified and in site finished with 1mm laminate and edges finished with 2mm thick PVC edge banding tape as instructed by Engineer in charge and fixed with SS handes, locks of approved brands, supporting clips, etc. and provided with bushes at bottom concealed. The top shall be of 19 mm Marine ply wood with front, rear and sides finished with 2mm/1mm mm thick PVC edge banding tapes of matching shade as instructed by Engineer in charge. Size of table 1200x450 (Refer Dwg. A-04)

Main Table ( 1800x750)

Fabricating and supplying at site, office table for the main counters made of 19 mm thick laminated MPW [BWP Grade] IS: 710 boxing as shown in drawing. The shutters, shelves shall be of 18 mm thick MPW laminate and drawers fixed on SS drawer channels, as per the size specified and in site finished with 1 mm laminate and edges finished with 2mm thick PVC edge banding tape and fixed with SS handes, locks of approved brands etc. and provided with bushes at bottom concealed. The top shall be of 19 mm Marine ply wood with front , rear, and sides finished with 2mm/1 mm thick PVC edge banding tapes of matching shade as instructed by Engineer in charge. Size of table 1800x750 (Refer Dwg. A-05)

Main Table ( 1450x750)

Fabricating and supplying at site, office table for the main counters made of 19 mm thick laminated MPW [BWP Grade] IS: 710 boxing as shown in drawing. The shutters, shelves shall be of 18 mm thick MPW laminate and drawers fixed on SS drawer channels, as per the size specified and in site finished with 1 mm laminate and edges finished with 2mm thick PVC edge banding tape and fixed with SS handes, locks of approved brands etc. and provided with bushes at bottom concealed. The top shall be of 19 mm Marine ply wood with front, rear, and sides finished with 2mm/1 mm thick PVC edge banding tapes of matching shade as instructed by Engineer in charge. Size of table 1450x750 (Refer Dwg. A-06)

Lock for wooden door

Providing and fixing mortise lock set of godrej or equivalent approved by Engineer in charge to the wooden door shutter (handle size minimum 8inch)

Supply 100A, 4 way Vertical DB

Supply of 3phase 415V distribution boards in sheet steel enclosure with double door detachable dland plate, complete with cable entry adapter box, tinned copper busbars,neutral link, earth bar din bar, knockouts, interconnections, earth studs etc. as required, without MCCB/ MCBs For concealed flush mounting Make: Standard/ Havells/ ABB/ Siemens/Hager/ Schneider- 100A, 4 way Vertical DB

Supply of 63A, 6 way Horizontal DB

Supply of 3 phase 415V Distribution boards in sheet steel enclosure with double door and detachable gland plate, complete with cable entry adapter box, tinned copper busbars, neutral link, earth bar, knockouts, din bar, interconnections, earth studs etc. as required, without MCCB/MCBs. For Concealed Flush mounting. Make: Standard/ Havells/ABB /Siemens/Hage r/Schneider.(63A, 6 way Horizontal DB)

Supply of 63A,4 way Horizontal DB

Supply of 3 phase 415V Distribution boards in sheet steel enclosure with double door and detachable gland plate, complete with cable entry adapter box, tinned copper busbars, neutral link, earth bar, knockouts, din bar, interconnections, earth studs etc. as required, without MCCB/MCBs. For Concealed Flush mounting. Make: Standard/Havells/ABB/Siemens/Hager/Schneider. (63A,4 way Horizontal DB)

Supply of 100A, 4 pole MCCB

Supply of four pole MCCB/RCCB/ MCB of the following capacity (Make: Standard/ Havells/ ABB/ Siemens/Hager/ Schneider)- 100A, 4 pole MCCB

Supply of 63A, 100mA 3Phase RCCB

Supply of four pole MCCB/RCCB/ MCB of the following capacity (Make: Standard/ Havells/ ABB/ Siemens/Hager/ Schneider)- 63A, 100mA 3Phase RCCB

Supply of four pole MCCB/RCCB/ MCB 63A, 4 pole MCB (C curve, 10 kA)

Supply of four pole MCCB/RCCB/ MCB of the following capacity (Make: Standard/ Havells/ ABB/ Siemens/Hager/ Schneider)- 63A, 4 pole MCB (C curve, 10 kA)

Supply of four pole MCCB/RCCB/ MCB 32A, 4 pole MCB (C curve, 10 kA)

Supply of four pole MCCB/RCCB/ MCB of the following capacity (Make: Standard/ Havells/ ABB/ Siemens/Hager/ Schneider)- 32A, 4 pole MCB (C curve, 10 kA)

Supply of four pole MCCB/RCCB/ MCB 10A, SP MCB (B curve, 10kA)

Supply of four pole MCCB/RCCB/ MCB of the following capacity (Make: Standard/ Havells/ ABB/ Siemens/Hager/ Schneider)- 10A, SP MCB (B curve, 10kA)

Supply of four pole MCCB/RCCB/ MCB 6A, SP MCB (B curve, 10kA)

Supply of four pole MCCB/RCCB/ MCB of the following capacity (Make: Standard/ Havells/ ABB/ Siemens/Hager/ Schneider)6A, SP MCB (B curve, 10kA)

Supply of four pole MCCB/RCCB/ MCB 20A, SP MCB (C curve, 10kA)

Supply of four pole MCCB/RCCB/ MCB of the following capacity (Make: Standard/ Havells/ ABB/ Siemens/Hager/ Schneider) 20A, SP MCB (C curve, 10kA)

Supply of cables- UTP/ Ethernet

Supply of cables- UTP/ Ethernet Cat 6 cable, Make : D-Link, Finolex, Polycab, Lapp

Supply of telephone cables

Supply of cables-Telephone cable, twin flat copper PVC insulated, 2x0.5mm,ISI marked, Make:Finolex, Anchor, V-Guard, Traco, Sark, Orbit, Polycab

Supply of LED down light(165 mm Dia)

Supply of LED downlight round (165 mm dia approx ), 9W (Approximate), 230V, 50Hz AC supply, with spring buckle for concealed false ceiling mounting, Lumen efficacy: 90 Lumens/W or above, Lumens: 810 Lumens or above, THD: 15% or less, PF: 0.90 or above, CRI: 80 or above, Colour temperature: Cool White(5500-6500K), IP: 20 or above, Warranty: Full warranty of 1 year or above

Supply of LED down light( 225mm Dia)

Supply of LED downlight round (225 mm dia approx ), 20W (Approximate), 230V, 50Hz AC supply, with spring buckle for concealed false ceiling mounting, Lumen efficacy: 90 Lumens/W or above, Lumens: 1800 Lumens or above, THD: 15% or less, PF: 0.90 or above, CRI: 80 or above, Colour temperature: Cool White(5500-6500K), IP: 20 or above, Warranty: Full warranty of 1 year or above

Wall fan

Fan Wall mounting type 18''(450mm) sweep Tilt up down: 90 deg to 180 deg Make: Orient/Usha/Crompton/Bajaj/Khaithan

Supply of electrical calling bell

Supply of Electrical calling bell, 230V,50Hz Make: Anchor, LT, Legrand : Supply of Electrical calling bell, 230V,50Hz Make: Anchor, L&amp;T, Legrand

Supply of bell switch

Supply of Bell switch, for 1 module, Make: Legrand, Anchor, ABB, Honeywell

Supply of 6A switch, for 1 module,

Supply of 6A switch, for 1 module, modular, Make: Legrand, Anchor, ABB, Honeywell

Supply of 25A switch, for 1 module

Supply of 25A switch, for 1 module, modular, Make: Legrand, Anchor, ABB, Honeywell

Supply of 5A-13A multistandard/ international Socket,

Supply of 5A-13A multistandard/ international Socket, for 2 module, modular, Make: Legrand, Anchor, ABB, Honeywell

Supply of 25A socket, for 2 module,

Supply of 25A socket, for 2 module, modular, Make: Legrand, Anchor, ABB, Honeywell

Supply of RJ11 socket, for 1 module,

Supply of RJ11 socket, for 1 module, modular, Make: Legrand, Anchor, ABB, Honeywell

Supply of RJ45 socket, for 1 module

Supply of RJ45 socket, for 1 module, modular, Make: Legrand, Anchor, ABB, Honeywell

Supply of Fan step regulator, for 2 module,

Supply of Fan step regulator, for 2 module, modular, Make: Legrand, Anchor, ABB, Honeywell

Supply of Concealed box, Plate and frame for 2 module,

Supply of Concealed box, Plate and frame for 2 module, modular, Make: Legrand, Anchor, ABB, Honeywell

Supply of Concealed box, Plate and frame for 3 module

Supply of Concealed box, Plate and frame for 3 module, modular, Make: Legrand, Anchor, ABB, Honeywell

Supply of Concealed box, Plate and frame for 6module

Supply of Concealed box, Plate and frame for 6module, modular, Make: Legrand, Anchor, ABB, Honeywell

Supply of Concealed box, Plate and frame for 9 module,

Supply of Concealed box, Plate and frame for 9 module, modular, Make: Legrand, Anchor, ABB, Honeywell

Supply of materials required for copper point wiring - 1.5 sq.mm

Supply of materials required for copper point wiring for lights, fans in PVC medium gauge conduit with modular type switch using 1.5 sq. mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 1.5 sq. mm. PVC insulated copper wire as required, complete. (Excluding supply of Fans, Exhaust fans, Lights, concealed mounting boxes, Plates and Frames, Switches, Sockets and Fan regulators) (Approximate 5 meters/point)

Supply of materials required for copper point wiring - 1.5 sq.mm for more than 5 meters.

Supply of materials required for copper point wiring as 68 .01 above for more than 5 meters.

Supply of materials required for copper circuit wiring in PVC conduit-with 2.5 sq.mm.

Supply of materials required for copper circuit wiring in PVC conduit-with 2.5 sq.mm. PVC insulated, copper conductor, standard cable in recessed PVC conduit along with 1 no. 2.5 sq. mm. PVC insulated copper wire for loop earthing as required.

Supply of materials required for copper circuit wiring in PVC conduit-with 1.5 sq.mm.

Supply of materials required for copper circuit wiring in PVC conduit-with 1.5 sq.mm. PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no. 1.5 sq. mm. PVC insulated copper wire for loop earthing as required.

Supply of telephone junction box

Supply of 10 pair telephone junction box and accessories for flush mounting, make: Syntex, Krone

Installation, testing and commissioning of LED

Installation, testing and commissioning of LED downlight of all types complete with all accessories etc. in false ceiling including connection with 1.5 sq.mm. PVC insulated copper conductor single core cable etc. as required.

Installation of ceiling fans/wall fans,

Installation of ceiling fans/wall fans, making connections, testing and commissioning etc. with 1.5 sq.mm. PVC insulated copper conductor single core cable etc. as required.

Installation of exhaust fan up to 300 mm sweep

Installation of exhaust fan up to 300 mm sweep in the existing opening including modifying the holes to suit the size of the above fan making good the damage, connections, testing and commissioning etc. with 1.5 sq.mm. PVC insulated copper conductor three core cable etc. as required

Installation of calling bell

Installation of calling bell at DCW room making connections, testing and commissioning etc. with 1.5 sq.mm. PVC insulated copper conductor single core cable etc. as required.

Installation, testing and commissioning of Smoke Detectors

Installation, testing and commissioning of Smoke Detectors complete with all accessories

Fixing of 6/5-13/16/25 amps modular type sockets,

Fixing of 6/5-13/16/25 amps modular type sockets,switches, bell switches, fan step regulators, RJ11 and RJ45 modular sockets with front plate in surface or in recess including providing and fixing suitable size metal box, inter connections etc. required.

Copper point wiring- 1.5 sq.mm.

Copper point wiring in PVC medium gauge conduit with modular type switch- Wiring for light point /fan point/ exhaust fan point/calling bell/socket point using 1.5 sq.mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 1.5 sq.mm. PVC insulated copper wire as required, with modular type switch with non-metallic inner and outer cover (inner and outer plate) in suitable metal box etc. as required to complete

Copper point wiring more than 5 m

Copper point wiring as 79.01 above for more than 5 meters.

Copper circuit wiring in PVC conduit-Circuit Wiring with 2.5 sq.mm.

Copper circuit wiring in PVC conduit-Circuit Wiring with 2.5 sq.mm. PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no. 2.5 sq.mm. PVC insulated copper wire for loop earthing as required

LAN circuit wiring in PVC conduit- Circuit Wiring

LAN circuit wiring in PVC conduit- Circuit Wiring with UTP/Ethernet cable in recessed PVC conduit as required

Telephone circuit wiring in PVC conduit-Circuit

Telephone circuit wiring in PVC conduit-Circuit Wiring two core telephone cable in recessed PVC conduit as required

Concealing of existing cables and conduits,

Concealing of existing cables and conduits, including conduit wherever required

Installation, testing and commissioning 100A, 4way Vertical DB

Installation, testing and commissioning (Concealed Flush mounting) Distribution board, in sheet steel enclosure with double door and detachable gland plate, complete with cable entry adaptor box, tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required. 100A, 4way Vertical DB

Installation, testing and commissioning . 63A, 4way Horizontal DB

Installation, testing and commissioning (Concealed Flush mounting) Distribution board, in sheet steel enclosure with double door and detachable gland plate, complete with cable entry adaptor box, tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required. 63A, 4way Horizontal DB

Installation, testing and commissioning 64A, 6way Horizontal DB

Installation, testing and commissioning (Concealed Flush mounting) Distribution board, in sheet steel enclosure with double door and detachable gland plate, complete with cable entry adaptor box, tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required. 64A, 6way Horizontal DB

Fixing single pole/three pole/four pole RCCB, MCBs 100A, 4 pole MCCB

Fixing single pole/three pole/four pole RCCB, MCBs in the existing enclosure and giving connections as required. 100A, 4 pole MCCB

Fixing single pole/three pole/four pole RCCB,63A 100mA 3phase RCCB

Fixing single pole/three pole/four pole RCCB, MCBs in the existing enclosure and giving connections as required. 63A 100mA 3phase RCCB

Fixing single pole/three pole/four pole RCCB, MCBs 63A, 4pole MCB (C curve, 10kA)

Fixing single pole/three pole/four pole RCCB, MCBs in the existing enclosure and giving connections as required. 63A, 4pole MCB (C curve, 10kA)

Fixing single pole/three pole/four pole RCCB, MCBs32A, 4pole MCB (C curve, 10kA)

Fixing single pole/three pole/four pole RCCB, MCBs in the existing enclosure and giving connections as required. 32A, 4pole MCB (C curve, 10kA)

Fixing single pole/three pole/four pole RCCB, 6A, SP MCB (B curve, 10kA)

Fixing single pole/three pole/four pole RCCB, MCBs in the existing enclosure and giving connections as required. 6A, SP MCB (B curve, 10kA)

Fixing single pole/three pole/four pole RCCB, MCBs 20A, SP MCB (C curve, 10kA)

Fixing single pole/three pole/four pole RCCB, MCBs in the existing enclosure and giving connections as required. 20A, SP MCB (C curve, 10kA)

Fixing single pole/three pole/four pole RCCB, MCBs 10A, SP MCB (B curve, 10kA)

Fixing single pole/three pole/four pole RCCB, MCBs in the existing enclosure and giving connections as required. 10A, SP MCB (B curve, 10kA)

Laying, dressing and clamping of 3.0x1.5 Sq.mm AYFY/XLPE Cable

Laying, dressing and clamping of following cables through existing trays/ structures/racks/columns etc to the new PDB. Cable shall be supplied by KMML. All other materials required for clamping are under the scope of contractor. 3.0x1.5 Sq.mm AYFY/XLPE Cable

Laying, dressing and clamping of (3.5x25 to 3.5x50) Sq.mm AYFY/XLPE Cable

Laying, dressing and clamping of following cables through existing trays/ structures/racks/columns etc to the new PDB. Cable shall be supplied by KMML. All other materials required for clamping are under the scope of contractor. (3.5x25 to 3.5x50) Sq.mm AYFY/XLPE Cable

Glanding and termination 3.0x1.5 Sq.mm AYFY/XLPE Cable

Glanding and termination at DB side of PVC cable using DC glands/lugs including supply of cable glands, lugs, aluminium crimping sockets, nuts bolts etc. required for this work. Gland earthing as per standards shall be done by the contractor. 3.0x1.5 Sq.mm AYFY/XLPE Cable

Glanding and termination (3.5x25 to 3.5x50) Sq.mm AYFY/XLPE Cable

Glanding and termination at DB side of PVC cable using DC glands/lugs including supply of cable glands, lugs, aluminium crimping sockets, nuts bolts etc. required for this work. Gland earthing as per standards shall be done by the contractor. (3.5x25 to 3.5x50) Sq.mm AYFY/XLPE Cable

Preparation of all electrical drawings

Preparation of all electrical drawings and obtaining statutory approval from electrical inspectorate for the new DBs

Bidder Name

M ABDULSHUKKOOR