Neendakara Fishery Harbour _ Upgradation of Panel board and street lights

Amount

Fabricating, supplying, conveying, lifting and erecting tubular post of overall height 9 m using 150mm and 125mm of Heavy duty G.I. Pipe sections having ISI mark and of approved quality(TATA , ZENITH , APOLLO) as per the drawing erected on a RCC footing, using 1:2:4 CC with nominal reinforcement and 6 Nos. of PCC well steining having 0.9m dia and 0.30m height with a muffing of 0.6mx0.6mx1m and 8 numbers of 20mm dia 2.80m long MS foundation bolts having 150mm long standard thread on both ends and 3Nos 20mm and 2Nos 20mm nuts at the top and bottom for each bolt . The post is to be provided with a 20mm thick MS flange of OD 300mm with 8 nos of 20mm bolt holes and a base plate of 600mm square 10mm thick with 8 Nos 20mm dia bolt holes embedded in the concrete 1.8m below ground level. The post should have a 1500mm dia ring made out of 50mm heavy GI pipe with cross supports using 40mm heavy GI pipe at the top for mounting the luminaries and its control gears. A 10mm thick MS flange having OD 300mm at 1200mm below the first ring mounted to the post . The top of the pipe should be sealed with 125mm table F Dummy flange. 12mm dia wire rope is to be provided for the entire length of the post as mechanical support for the cables to the luminaries. Inverted Y arrangement using 50mm heavy GI pipe and flanges at the top and 75mm 4kgf/cm2 PVC pipe with bend to be provided in the concrete muffing for taking out cables. 8 x 75mm stainless steel Bolt & Nut shall be used for fixing all the flange covers..The post is to be painted with two coats of UV resistant polyeruthene paint of approved quality and colour over two coats of best quality industrial epoxy primer and epoxy paint..All steel items shall be hot dip galvanised.

Supply of SID or equivalent make Street light luminaire, 20W LED, IP66 optical & control gear compartment, die cast aluminium painted housing,anti UV Polycarbonate protector with in built lenses, with easily accessible control gear compartment, suitable for horizontal mounting (Ø32- 42mm), System power (including driver loss) of 20W with luminous efficacy > 105 Lumen/W at Ta 25⁰C. Lifetime residual flux @ Tq 35⁰C @ 50,000 hours = 70%, Ta = 50⁰C, in built surge protection of 4kV (in Differential and Common mode), Power Factor > 0.95, Colour Rendering Index > 70 and Cool white light (5700⁰K).

Supply of BIS approved LED Luminaire with system wattage of 35W, made up of pressure die cast Aluminium body and anti UV PC Protector with integrated lenses for increased pole spacing and uniform light distribution, IP66, IK 08, system efficacy of 110 lm/W, CCT 4000K, operating temp range up to 50 degree and designed for efficient thermal management, lumen maintenance L70@ 50000Hrs, Upward Light Output Ratio is 0% at zero degree inclination to avoid light pollution, suitable for side / vertical mounting up to 48mm diameter, Colour Rendering Index > 70, a driver efficiency > 85%, with internal surge protection of 4kV and Power factor > 0.95.Make: Keselec Cat Ref: Nice-R 35W NW LED or equivalent

Supplying IP66, IK 10 rated 200W NW flood light luminaire with body of aluminium extrusion having luminaire efficacy >= 120lumen/watt supplied with IP67 rated best in class LED driver. Prefered make:Keselec-K Flood 200W- NW

Supply and fixing brass batten / angle holder including connection etc as required

Supply and fixing 7/9 W LED lamp OSRAM / Philips or equivalent

Supplying LED luminaire Philips WT 201 C LED 20S - 6500 PSU L 120 IP 65 or equivalent

Supply and fixing cast aluminium stove enameled elliptical shaped bulk head fittings with porcelain holder and mesh guard suitable for LED Lamps including connection etc as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

Conveyance, installation, testing and commissioning of T 5 outdoor light fitting with FL lamps/LED/ SV/ MH/ CDMT light fittings with all accessories and lamp etc. of all types directly on the existing pipe/ pole including giving connections with the existing wiring etc as required

Conveyance, installation, testing and commissioning of departmentally supplied flood light/ area light luminaire with lamp to a height upto 15m from ground level.

Conveyance, installation, testing and commissioning of departmentally supplied flood light/ area light luminaire with lamp to a height upto 8m from ground level.

Dismounting the SV lamp from the tubular post of height upto 15m from ground level without any damage and keep at a place as per the instruction of the depatmental officer at site.

Scaffolding charges for for painting

Fabricating and supplying special clamping arrangement for fixing an asymmetrical beam Integral LED flood light on pipe with clamps each made out of 50 x 6mm MS flat and 8x40mm SS nuts and bolts for one luminaire. The clamps are to be linked with 40x6mm MS flat with suitable holes 8mm ,10mm or 12mm size with suitable size SS Bolt& Nut to fix the luminaire. All the items are to be painted with two coats of epoxy based industrial primer of approved quality and two coats of best quaity synthetic enamel paint of approved colour as per drawing.

Fabricating and supplying special clamping arrangement for fixing cable junctionbox on 75 mm dia GI pipe ring with two clamps each made out of 40 x 6mm MS flat and 8x40mm SS nuts and bolts for one luminaire. The clamps are to be linked with 40x6mm MS flat with suitable holes 8mm ,10mm or 12mm size with suitable size SS Bolt& Nut to fix the junction box. All the items are to be painted with two coats of epoxy based industrial primer of approved quality and two coats of best quaity epoxy paint of approved colour as per drawing.

Supply, fabrication, conveyance and fixing the following sizes of B class GI pipe bent to shape and fixing the same to wall / parapet using clamps as noted along with each size, painting with 2 coats of synthetic enamel paint over a coat of zinc chromate primer, making good the damages, colour washing etc as required (for the installation of outdoor light fittings).40 mm dia with clamps made from 20 x 3 mm MS flat

Wiring for light point/ fan point/ exhaust fan/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required(Group C)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25mm

Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.3 x 1.5 sq. mm

Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.3 X 4.0 sq. mm

Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.6 X 4.0 sq. mm

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing following size / modules, Plastic boxes alongwith modular base & cover plate for modular switches on surface or in recess etc as required.1 or 2 Module plastic box

Supplying and fixing following size / modules, Plastic boxes alongwith modular base & cover plate for modular switches on surface or in recess etc as required. 3 Module plastic box

Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

Supplying, fabricating , erecting and commissioning floor mounting, fully compartmentalised, dust and vermin proof cubicle MAIN panel board of size 1250 x 1450 x 250mm or nearest suitable size using 16 G CRCA MS sheet, painting two coats of best quality epoxy paint over two coats of epoxy primer, having one vertical bus bar chamber, three vertical and one horizontal cable alley having front openable bolting type cover with cable entry provisions, bolted type cable glanding plate using 14 SWG CRCA MS sheet at the top and bottom. The panel should have 75x40x6mm MS channel provided at the bottom as support and comprising the following. Incomer:- 125 A, AC 23-A, 4 pole on-load Change Over Switch in open Execution, Incoming:- 100A, 35kA FP MCCB setted to 80A and rotory drive kit including BUC handle and shunt release with auxiliary contact- 1No, Outgoings:- 40 A FP MCCB 25 KA - 1No with rotary handle , 40 A TP MCCB 25 KA setted to 32A - 1No with rotary handle and 32 A two way disconnectable type neutral link and rotary handle - 1 No, 25 A TP MCCB 16 KA setted to 20A - 4Nos with rotary handle and 32 A two way disconnectable type neutral link suitably connected All switches and MCCB should be of panel mounting and conforming to IS:13947part III (L&T/SIEMENS/Legrand), Busbar Chamber: Busbar chamber with 38X3mm Copper strips 4 Nos or equivalent size one each for phases and neutral fitted on epoxy insulator. Switch interconnections to be done with suitably rated Copper conductors insulated with PVC heat shrinkable sleeves. Interconnections with the incoming and is also to be carried out using 25x3mm PVC insulated Copper strips supported using epoxy insulators and outgoing with suitable rated copper conductor as required. Protection :- ELR with CBCT , 3 Phase 4 wire Under & Overvoltage relay (Auto/ manual reset ,Trip time and Power on delay 1 - 10 sec) OV / UV - adjustable and Reverse phase sequence relay and phase sequence relay, 2 NO+2 NC Auxiliary relay with 230 V Ac coil including giving interconnection with suitably rated PVC insulated copper wire with terminals. Metering and Indication:- Panel surface mounting 96 Sq.mm LED Multi-function meter with three line display to read V,A,,kVA,kVAr,PF,KW and frequency of make Schnider or equivalent suitable for 415V,50Hz with RS 485 communication port- 2No, RS 485 to ethernet converter-1 No, SMP power supply- 1 No, 100/5 A Tape wound CT 3 Nos , and 2A SP MCB C Curve (Cat B)-6Nos and a 63A two way disconnectable type neutral link inside the cubicle. The panel board should have hinged shutters and quarterturn key lock for OLCOS/ MCCB cubicles and front openable bolted type busbar covers and it should be fabricated as per Kerala State Electrical Inspectorate's norms and only after obtaining approval from the departmental officers at site for the design. Panel internal earthing should be provided using 38x3 mm copper strip with two earthing points at bottom side. (Panel drawing attached with the schedule)

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, 25A residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 40A, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 40 A double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing four pole, 415 volts, 40A isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Providing and fixing 0.3 m , 25 mm X 3 mm tinned copper strip on surface or in recess for connections etc. as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Upto 35 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle).

Supply of 4 core 4.0 sq mm PVC insulated and PVC sheathed armoured copper Power cable

Supply of 2 core 2.5 sq mm PVC insulated and PVC sheathed armoured copper control cable

Supply of 4 core 10 sq mm PVC insulated and PVC sheathed armoured aluminum cable

Supply of 4 core 16 sq mm PVC insulated and PVC sheathed armoured aluminum cable

Supply of 3.5 core 50 sq mm PVC insulated and PVC sheathed armoured aluminum cable

Supply of 3 core 2.5 sq mm PVC insulated and PVC sheathed submersible copper cable

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4C x 10 sq.mm (25mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4C X 16 sq. mm (28mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3.5C X 50 sq. mm (35mm)

Supplying and making end termination nickel plated single compression brass cable gland for 4 core 4 sq mm PVC insulated and PVC sheathed armoured copper conductor cable 1.1 KV grade, including providing earth clip and superior quality copper cable socket.

Supply of 50/38mm (OD/ID) Double Walled Corrugated (DWC) pipes made out of HDPE for mechanical protection to under ground power/communication/ OFC / Signal cable conforming to IS 14930 Part - II,

Excavation for cable trenches of depth upto 1.2 m in soft soil including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 metre.

Providing and fixing10 SWG copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Providing and fixing 6 SWG copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Supply and laying bare earthing copper conductor 6 SWG laid 0.6 m below ground level including excavating trench of suitable size and refilling etc. as required (in Ordinary soil).

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Providing and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and re-filling as required.

Supply and providing 25x6 mm brass bolt and nut with washers on the existing MS box / earth bus etc. as required including drilling necessary holes as required

Supply of superior quality copper earth socket for the 3.15mm (10 SWG) earth conductor including crimping etc. as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. (but without charcoal/ coke and salt) as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. (but without charcoal/ coke and salt) as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

Supply and fixing Thermoplastic polycarbonate Cable Junction Boxes IP 65 for outdoor applications ( with knock outs for cable entry )) suitable for cable sizes 16 sq.mm ,182 X 180 X 111 mm CAPE model No TKPC1818 -11 withTerminals or equivalent and accessories for Cable Junction Boxes such as Copper Terminal Set including fixing the accessories using suitable size Stainless steel Bolt and nut, giving necessary connections, making good the damages etc. as required.

Fabrication ,supply, erection and commissioning of cubicle wall mounting type CRCA sheet board of 4000x400x250mm or nearest size wall mounting arrangement having hinged door with locking/sealing provision .

Supply and fixing Cable Junction Boxes IP 65 for outdoor applications (Thermoplastic Polycarbonate ) suitable for cable sizes 2.5 sq.mm ,80 X 80X 52 mm Cape model Abox i025 or equivalent and accessories for Cable Junction Boxes such as Copper Terminal Set 2.5 sq.mm 5 Pole 1 No,Support for Terminal 1No including fixing the accessories using suitable size Stainless steel Bolt and nut, giving necessary connections, making good the damages etc. as required.

Supply and installation of Glass Fibre Reinforced Polyester enclosure with Hinged door IP66 , IK 10 , 600x500x230 mm,BRES -65 CAPE make with baseplate for fixing for fixing CT, KSEB electronic energy meter, cut outs and neutral link. Supply and providing 3 Nos of 125A HRC fuse units with 63A HRC fuse link and 1No 100A 2way neutral link in the meter portion. Necessary holes are to be provided in the box for entry and exit of wire The inter connection should be done using 16.0 sq.mm copper wire.

Supply and installation of wall mounting cubicle type dust and vermin proof CAPE make CA63a , 540x270x205mm IP66,IK 10 Glass fibre reinforced polyester enclosure including supply and fixing 100 A , 25kA FP MCCB, with rotary handle, 3 Nos phase indication lamp and 3 Nos 2A SP MCB including wiring using 2.5 sq.mm wire for control wiring .

Supply and fixing IP 65 outdoor installation CAPE 24 module( Model No Aki 24) 370x250x122mm Thermoplastic polycarbonate MCB distribution board with PE + N Terminals on the surface using suitable size stainless steel screws.

Supply and fixing IP 65 outdoor installation CAPE 9 module( Model No Aki 09) 200x200x122mm Thermoplastic polycarbonate MCB distribution board with PE + N Terminals on the surface using suitable size stainless steel screws.

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Supply and fixing 3 phase,415V, 1 KVAR, ISI marked Heavy Duty Power factor improvement Capacitor with test certificate in the existing enclosure

Repairing the existing 6m light pole by attending necessary repairs by cutting and removing the bended and fractured portion by jointing with 1m length 80mm Heavy GI pipe painting the repaired portion with 2 coats of indusrial epoxy paint over 2 coats of industrial epoxy primer Lifting and erecting the repaired tubular pole on the existing foundation and giving connection etc complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Painting with 2 Coats of Industrial based Epoxy primer of approved brand and manufacture on steel galvanised iron/steel works (2 Coats)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Providing and laying in position reinforced cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required (excluding reinforcement).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Providing 15mm thick cement plaster of mix 1:4 (1 cement : 4 fine sand) at all levels.

Providing and fixing B class G.I. pipes with ISI mark complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 50 mm dia nominal bore

Supplying IP66, IK 10 rated 100W NW flood light luminaire with body of aluminium extrusion having luminaire efficacy >= 120lumen/watt supplied with IP67 rated best in class LED driver. Preffered make:Keselec-K Flood 100W- NW

Supply and installation of wall mounting cubicle type dust and vermin proof CAPE make CA63 , 540x270x170mm IP66,IK 10 Glass fibre reinforced polyester enclosure including providing 0.20m copper earthstrip of 25 x 3mm

Supply and fixing Cable Junction Boxes IP 65 for outdoor applications (Thermoplastic Polycarbonate ) suitable for cable sizes 2.5 sq.mm ,80 X 80X 52 mm Cape model Abox i025 or equivalent and accessories for Cable Junction Boxes such as Copper Terminal Set 2.5 sq.mm 5 Pole 1 No,Support for Terminal 1No including fixing the accessories using suitable size Stainless steel Bolt and nut, giving necessary connections, making good the damages etc. as required.

Supply and providing 6Kg stored pressure ABC Powder type Fire Extinguisher with hose and clamps including fixing it to wall as required.

Supply and providing 6 mm thick & 1 m wide electrical grade chequered type rubber mat to withstand 3.3 KV dielectric strength conforming to IS 15652/2006

Supply and providing 9 litre capacity GI Fire Bucket painted in post office red with primer coat of red oxide and written with white paint "FIRE" mounted on MS angle frame work/wall bracket fillled with fine sand, painting the frame work/floor stand including making good the damages, colour washing etc.as required.

Supply and providing First Aid Chart duly framed and placed in a conspicuous location for clear vision

Supply and providing single line diagram duly framed,laminated and placed in a conspicuous location for clear vision

Engaging labourers for dismantling the existing damaged meter board,panel board , electrical wiring and installations and keeping the same safely at a place as per the direction of the departmental officers at site Wireman

Engaging labourers for dismantling the existing damaged meter board,panel board , electrical wiring and installations and keeping the same safely at a place as per the direction of the departmental officers at site. Beldar