Interior Fit-Out Works of 6 nos. SIDBI Branch Offices (6 nos. EBOs) in Central East Zone covering Telangana, Jharkhand, Bihar and West Bengal

Sr.No Description DSR Amount Non- DSR Amount

Total (DSR +MR) BOQ Amount 1,25,39,704.00

Total cost (i/c GST) 1,25,39,704.00

Digitally signed by MANISH

SCHEDULE OF QUANTITIES - CIVIL WORKS

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

CIVIL & INTERIOR WORKS

Dismantling tile work in floors , Wall and roofs laid in cement mortar including

stacking material within 50 metres lead.

15.23.2 For thickness of tiles above 25 mm and up to 40 mm SQM 12 113.55 1362.60

Demolishing brick work manually / by mechanical means including stacking of

1.2 15.7 serviceable material and disposal of unserviceable material within 50 metres lead

as per direction of Engineer-in-Charge.

15.7.4 In cement mortar Cum 6 2060.20 12361.20

Carriage of material by mechanical transport including loading unloading and

1.1.1 Lime, murrum, building rubbish

2 MASONRY AND PLASTER

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

2.1 11.3 aggregate) finished with a floating coat of neat cement, including cement slurry,

but excluding the cost of nosing of steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate SQM 12 614.20 7370.40

CEMENT PLASTER :- 15 mm cement plaster on the rough side of single or half brick

2.5 13.4 12 mm cement plaster of mix

POP PUNNING (12mm-15mm) : Providing and fixing Average 12mm to 15mm thick

2.6 MR POP Punning over cement plaster in line & plumb finished smooth to receive SQM 300 301.33 90397.85

paint. (Internal surfaces of walls).

3 FALSE CEILING WORKS

Digitally signed by MANISH

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including

providing and fixing of frame work made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per

IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges

of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling

with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat

fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of

required size and other end of angle hanger fixed with intermediate G.I. channels

45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling

section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm

each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a

direction perpendicular to G.I. intermediate channel with connecting clips made out of

2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter

channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the

perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm

centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum

board to ceiling section and perimeter channel with the help of dry wall screws of size

3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered

and square edges of the board with recommended jointing compound , jointing tapes

, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint

and two coats of primer suitable for board, all as per manufacturer's specification

and also including the cost of making openings for light fittings, grills, diffusers,

cutouts made with frame of perimeter channels suitably fixed, all complete as per

drawings, specification and direction of the Engineer in Charge but excluding the cost of

12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011

(Board with BIS certification marks)

Providing & fixing of Silhoutee Frame ceiling tile in size 600x600x15mm having noise

reduction co-efficient of 0.7, Density of 100 kg / m3, and Humidity resistance of 95% to be

3.02 MR laid on exposed grid system with white wrap comprising main runner 3.00 mm x 24mm sq m 120 2450.00 294000.00

web height cross tee 1.2 mtrs x 24 mm web height and 0.6 mtrs x 24 mm web height. The

wall angle shall be 3.0 mtrs.

4 PARTITIONS AND WALL CLADDING

Digitally signed by MANISH

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

WALL PARTITION-Providing and fixing partition upto ceiling height consisting of

Aluminium frame and required board, frame work made of Aluminium section made of

50x25 mm , consisting of floor and ceiling channel 50mm wide having equal flanges of

25 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre

to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor

fastener or metal screws with nylon plugs and the studs 48 mm wide having one

flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within

flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to

centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of

4.01 MR partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs

at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work

by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300

mm centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick

having two flanges of 9.5 mm each) to be provided at the horizontal joints of two

boards, fixed to the studs using metal to metal flat head screws, including jointing

and finishing to a flush finish with recommended jointing compound, jointing tape, angle

beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher as per manufacture's

specification and direction of engineer in charge all complete.

Both side 12 mm thick HDHMR board to IS: 5509 sq m 90 3450.00 310500.00

LAMINATE CLADDING- P/F 1mm thick laminate including 4 mm thick MDF, on an existing

Plywood surface.

Providing and fixing 12mm thick frameless toughened glass door shutter of approved

brand and manufacture, including providing and fixing top & bottom pivot & double

5.04 21.18 acting hydraulic floor spring type fixing arrangement and making necessary holes etc. sq m 21 5325.90 111843.90

for fixing required door fittings, all complete as per direction of Engineer in charge (Door

handle, lock and stopper etc. to be paid separately)

Digitally signed by MANISH

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

Providing and fixing partition comprising 12 mm thick clear toughened safety glass of

approved make conforming to IS 2553 (Part-I) and IS 14900, fixed in anodized aluminium

U-channels of approved size and section at top, bottom and sides as required. The work

MR shall include machine polished exposed edges of glass, neoprene packing, EPDM sq m 54 3560.00 192240.00

gaskets, silicone sealant, aluminium channels, screws, fasteners, anchoring

arrangements, cutting, handling, transportation, installation, cleaning and all incidental

works complete as per approved drawings and direction of Engineer-in-Charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames,

5.05 9.1 wrought framed and fixed in position with hold fast lugs or with dash fasteners of

required dia & length (hold fast lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood cum 0.60 142949.70 85769.82

Providing and fixing partition top beading 80x12 mm, including cutting, shaping,

adhesive/fastener fixing, edge finishing, surface preparation, and applying polish with

matching finish, complete in all respects as per site requirement and engineer-in-charge

INSULATION- Providing and fixing thermal insulation with Resin Bonded rock wool

conforming to IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G

Virgin Polythene Bags fixed to wall wirh screw, rawel plug & washers and held and in

position by criss cossing GI wire etc. complete as per directions of Engineer-in-Charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board construction with frame of 1st class hard wood

and well matched commercial 3 ply veneering with vertical grains or cross bands and

face veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws sq m 24 2392.65 57423.60

Providing and applying panelling/partition with matching colour groove finish and

polishing, including all materials, labour, surface preparation, fixing accessories, edge

finishing, sanding, colour matching, groove cutting, polishing coats, and complete

finishing as per site requirement and engineer-in-charge directions.

Digitally signed by MANISH

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI marked, anodised

5.11 9.97 (anodic AC 10 as per IS : 1868 ), transparent or dyed to required colour or shade,

DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor door

stopper with necessary screws, etc. complete.

Door Closers: Providing and fixing aluminium extruded section body tubular type

universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the

body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with

double speed adjustment with necessary accessories and screws etc. complete.

MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular Handle TH 123

5.14 MR with Roses & Escutcheon in SS packaged with Mortice lockset 55mm backset, 20 SS EACH 12 2650.00 31800.00

forend, SS strike plate and EP Cylinder for all flush doors.

Providing and fixing 600 mmx25 mm H Type handle for Doors approved make and

designs as per engineer in charge

Providing and fixing minimium 70-90 kg capacity flooor spring for Doors approved make

and designs as per engineer in charge

Providing and fixing Glass door lock approved make and designs as per engineer in

5.18 MR Providing and fixing Glass Big -L approved make and designs as per engineer in charge each 12 2450.00 29400.00

Providing and applying plaster of paris putty of 2 mm thickness over plastered

surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC

(Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and

manufacture, including applying additional coats wherever required to achieve even

shade and colour.

Applying priming coats with primer of approved brand and manufacture, having low

VOC (Volatile Organic Compound ) content.

With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC

content less than 50 grams/ litre

Painting with synthetic enamel paint of approved brand and manufacture of required

colour to give an even shade :

Digitally signed by MANISH

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

13.99.1 One or more coats on old work. sq m 210 102.80 21588.00

BLINDS Providing & supplying of Window Blinds as per the approved sample in

required shade and style consisting, of ZEBRA BLINDS comprising of optima screen Fabric

comprising of 22% polyester, 78% PVC, Fabric weight 460-480G weight per sq m,

Thickness 0.67 mm, Yarn count 18- 19/cm, having fire resistance standard – NFPA 701-89

small testing ISO- 5659-2 .Thetear resistance should be complying to ISO4674 & breaking

resistance – ISO 5081. The DRIVE UNIT shall be of clutch for quick, easy and safe

installation, moulded plastic with steel spring support and inserted into the tube end. It

shall be driven by a ball chain pulley with ball chain and can be positioned at right side

or left hand side of the Shade. The Shade when lowering or raising, shall be

automatically locked in position upon release of the ball chain by means of a built in

friction lock.Universal clutch for left and right hand operation.Chain Gear Ratio of 1.75:1.

The END PLUG shall be molded of plastic witha steel location pin.The plug shall be

inserted into the tube end.(Opposite to the Drive Unit) for ease of installation. The

SUPPORT BRACKETS shall be of coated steel & provided with covers and used in right

M.R. hand or left hand positions differentiated by the acceptance of the of the rectangular sq m 40.41 2,450.00 99000.00

drive unit support or the round idler plug pin.Can beinstalled (a) On Face (b) Ceiling

Mount (c) On Frame

(d) in Recess. The Bracket should be protruding outside maximum of

80mm.The ROLLER TUBE shall be of extruded aluminum with 37mm internal diameter &

skin thickness of 1mm and shall incorporate a key way integral with the tube to

accommodate the spline. The BOTTOM RAIL shall be a Flat Bottom made up of powder

coated steel. The BALL CHAIN shall be 2mm diameter cord with 4.5mm diameter acetal

balls moulded co-axially to it on 6mm pitch to form an endless ball chain. It is used for

FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass surface as

approval of the Architect. (Only film surface area shall be measured and paid).

Providing & fixing Sidbi Signages & Logo & Sidbi Enviremoent Theme as per Direction of

Engineer in Charge

Providing . & fixing Sidbi Sign Glow Board For Exterior Acrylic Base Embeded Letter as per

Digitally signed by MANISH

S NO DSR/MR DESCRIPTION UNIT QUANTITY RATE AMOUNT AMOUNT

DSR 2023 VOL-1 DSR RATE NON DSR

Providing and fixing sandwich poster made of printed graphic mounted on required

thickness sunboard/ACP board, fixed directly on wall with SS decorative studs, complete

with all necessary hardware, fitting, and installation at site, as per approved design and

direction of engineer-in-charge.

Total Amount 1013480.82 1770568.84

Total Amount 1013480.82 1770568.84

Add labour cess @0.973 as per CPWD circular 986116.84

Add CPWD cost index @103 on DSR civil 2023 1015700.34

Total Amount 1015700.34 1770568.84

Total Amount 1015700.34 1770568.84

Total Amount DSR & NDSR 2786269.18

Total Amount DSR & NDSR 2786269.18

Digitally signed by MANISH

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface/ recessed medium class PVC

conduit, with modular switch, modular plate, suitable GI box

A.1 and earthing the point with 1.5 sq.mm. FRLS PVC insulated

copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call

bell point (without independent switch etc.) with1.5 sq.mm

FRLS PVC insulated copper conductor single core cable in

surface / recessed PVC conduit, and earthing the point with

1.5 sq.mm. FRLS PVC insulated copper conductor single core

cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

A.3 1.12 recessed medium class PVC conduit alongwith 1 No 4 sq. mm Metre 480 373.00 179040.00

FRLS PVC insulated copper conductor single core cable for

loop earthing as required.

Digitally signed by MANISH

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

Supplying and fixing following modular switch/socket on the

1.24 existing modular plate & switch box including connections but

excluding modular plate etc. a srequired.

1.24.4 3 pin 5/6 amp socket outlet Each 60 136.00 8160.00

1.24.5 6 pin 15/16 amp socket outlet Each 36 219.00 7884.00

Supplying and fixing modular blanking plate on the existing

A.5 1.26 modular plate & switch box excluding modular plate as Each 18 47.00 846.00

Supplying and fixing following size/module, GI box along with

1.27 Modular base & cover plate on existing modular metal boxes

etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire

with the following sizes of FR PVC insulated copper

conductor, single core cable in surface/ recessed medium

B.1 class PVC conduit as required

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 30 482.00 14460.00

Digitally signed by MANISH

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

Supply of following sizes of copper cables -PVC sheathed

PVC/XLPE insulated Copper conductor armoured cable of 1.1

KV grade conforming to IS:7098 part-1 / IS:1554 part-1

respectively & ISI marked.

(a) 4 C x 16 Sqmm XLPE copper cable RM 90 1300.00 117000.00

(b) 4 C x 25 Sqmm XLPE copper cable RM 12 1800.00 21600.00

Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts,

"C" curve, miniature circuit breaker suitable for inductive load

D.2 of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts,

2.13 isolator in the existing MCB DB complete with connections,

D.3 testing and commissioning etc. as required.

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/recess, complete with tinned copper bus bar,

D.4 neutral bus bar, earth bar, din bar, interconnections, powder

painted including earthing etc. as required. (But without

MCB/ RCCB/ Isolator)

Digitally signed by MANISH

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

Providing and fixing 400mm wall mounted oscillating fan,

heavy-duty type, 230V, 50Hz, single phase, with three-speed

control regulator, complete with suitable mounting brackets,

clamps, bolts, nuts, and necessary wiring connections from

the nearest point using 1.5 sq.mm copper flexible wire,

including testing and commissioning at site, complete as

required.( Make: Havells/Cromton/Usha/Bajaj asapproved by

ingineer-in-charge)

Supplying and fixing of following sizes medium class PVC

conduit aong with accessories in surface/ recess including

cutting the wall and making good the same incase of

recessed conduit as required

Earthing with copper earth plate 600 mm X 600 mm X 3 mm

thick including accessories, and providing masonry enclosure

F.1 5.6 with cover plate having locking arrangement and watering SET 6 15004.00 90024.00

pipe of 2.7 metre long etc. with charcoal/coke and salt as

Providing and fixing 25 mm X 5 mm copper strip on surface or

in recess for connections etc. As required.

Digitally signed by MANISH

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

Online UPS - Input supply: Single Phase, Output

Supply: Single Phase.

Supplying, installation, Testing & Commissioning of following

capacity at full load (Unity Power Factor) ON LINE

Uninterrupted Power Supply (UPS) system suitable for Single

Phase input, Single Phase output AC Supply. The UPS shall

include a Rectifier, inverter, battery bank suitable for 30

minutes back up (Battery VAH capacity shall not be

less than 1600 VAH per KVA of UPS rating per Hour

backup time) on full load (Battery shall be VRLA, SMF in ABS

Container) and Static Bypass switch along with provision for

manual bypass, suitable isolation transformer for additional

protection against neutral faults etc. The UPS systems shall be

Microprocessor based Digital Control, using Insulated Gate

1 26.2.1 Bipolar Transistor (IGBT)'s both for

the rectifier & inverter with PWM (Pulse Width Modulation)

Technology. The quality of design, manufacturing

and inspection process should confirm to the relevant Inter-

national standards such as IEC/EN/VDE. The operating

efficiency of the UPS systems shall be >95% at 100% non-linear

loads. Current total harmonic distortion(ITHD)/ total demand

distortion (TDD) on the input grid shall be < 5% at 100 %load.

(The required LC filters shall be included in UPS cost), extreme

power factor kit to be include to limit the input pf to 0.99 and

factor shall be unity (i.e. kw rating of the UPS shall be kva

rating x 1 ) however UPS shall be suitable to take load at 0.7

laging to 0.7 leading power factor loads. UPS shall be suitable

for incoming supply AC single phase 160-270V 50 Hz and

Digitally signed by MANISH

S NO DESCRIPTION UNIT QUANTITY RATE

2025 DSR (INR)

Providing & Fixing exhaust fan of approved make and size

complete with frame, mounting arrangement, necessary

MR wiring connection from nearby point, screws, fasteners, Nos 6 2150.00 12900.00

cutting/fitting work and testing & commissioning complete as

required at site

Total of Electrical items 1680444.00 857658.00

Total Amount 1680444.00 857658.00

Total Amount 1680444.00 857658.00

Total DSR+NDSR 2538102.00

Digitally signed by MANISH

S.No Description Unit Quantity Rate DSR Amount MR Amount

Supply , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete

with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation

(closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable

upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R407 Green Refrigerant, wireless Remote control,

suitable for working between 180-260V with low & high voltage cutoff and 50 hz ,1 phase AC supply

capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary

compressor. The system shall be able to deliver 100% of the rated capacity upto 42 Degree Celsius. Min 5

Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB).

Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electro

technical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS

2993 and motor IS 12615. Complete as per CPWD

specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door

ambient temperature).

a 32.2.2 1.0 TR with 5 Star BEE Rating Each 6 40580.00 243480.00

b 32.2.3 1.5 TR with 5 Star BEE Rating Each 12 43539.00 522468.00

c 32.2.4 2.0 TR with 5 Star BEE Rating Each 6 57396.00 344376.00

Supplying, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of

following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with

fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories,

insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile

rubber tubular sleeves sections of 19 mm thick insulation as given below for Suction and Liquid lines, all

accessories as per specifications etc. as required :

a 31.14.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Meter 90 256.00 23040.00

b 31.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Meter 300 346.00 103800.00

c 31.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Meter 390 487.00 189930.00

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2

Providing, laying, testing and commissioning of additional condensate drain piping in 25 mm dia uPVC

pipe, including all required uPVC fittings such as bends, sockets, tees, reducers, U-trap and clean-out

arrangement, clamps, supports, connection to nearest suitable drainage point, 6 mm thick insulation

3 MR wherever required, cutting and making good of surfaces, testing for proper flow and leakage and all Meter 333.27 202.00 67320.00

other materials, labour, tools and accessories, complete as required and as directed by Engineer-in-

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in

4 1.21 surface/recess including cutting the wall and making good the same in case of recessed conduit as

Digitally signed by MANISH

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for

5 2.10 inductive load of following poles in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current

7 2.14 circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V,

on surface/ recess, complete with tinned copper bus

bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as

required. (But without MCB/RCCB/Isolator)

2.3.1 6 way , Double door Each 6 2390.00 14340.00

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc.,including

cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including

welding and bolted with special shaped washers etc. complete.

10.16.1 Hot finished welded type tubes kg 240 194.40 46656.00

Total Amount (DSR+MR) 16,40,592.00 67320.00

Total Amount (DSR+MR) 16,40,592.00 67320.00

Total Amount 17,07,912.00

Total Amount 17,07,912.00

Digitally signed by MANISH

SCHEDULE OF QUANTITIES - DATA and VOICE WORKS

S NO Description UOM Qty Rate DSR Amount

A. 2025 UTP Components for Data

Supplying, drawing, Testing and commissioning of Cat6A UTP 4 pair, 23 AWG solid copper

cable in existing conduit/ on surface, U/FTP, LSZH, Non-

Plenum, Horizontal (solid) Cable suitable for high speed data networking application

supporting upto 10Gbps over a 100 meter channel. The 4 Unshielded Twisted Pairs (UTP)

1 1.53 cable with color coded insulation

for easy indentification should have FLAME PROPERTIES i.e. Flammability Test - IEC 60332-1,

Smoke Density - IEC 61034, LSZH standards compliance: ANSI/TIA-568 C.2, ISO/IEC 11801, IEEE

802.3an, RoHS. Delay Skew should be < 45NS. The outer Cable Diameter should be 7.5 + 2

mm. Cable should have been tested and verified by UL/ ETL etc. complete as required.

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable termination at Rack

Side. Keystone Unshielded Outlet, 180DG C6, Blue

Supply, Installtion, Testing and Comissioning of I/O port for CAT6 cable termination at Rack

Side end Redantant . Keystone Unshielded Outlet, 180DG C6, Yellow

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet) for

4 MR information outlet (I/O) to end user Redantant device connectivity.High Speed Gigabit Nos. 72 420.00 30240.00

24AWG U/UTP Patch Cord Blue, LSZH, C6, 2M (Blue)

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet) for

5 MR information outlet (I/O) to Rack End Redantant device connectivity.High Speed Gigabit Nos. 72 420.00 30240.00

24AWG U/UTP Patch Cord Yellow, LSZH, C6, 2M (Yellow)

Supply, Installtion, Testing and Comissioning of 24 port Loaded Angled Staggred Jack Panel

for CAT6 cable termination at rack end. Data Active Redandant

Supply , Installtion , Testing and Comissioning of 2 Port British Style Shuttered Face Plate white for I/O

fixing at user side

8 MR SITC of 04 core OM3 Multimode fiber orange color 50/125, minimum bending radius 15x OD RM 90 229.17 20625.00

Digitally signed by MANISH

SITC of 24U Floor Standing Network Rack, of suitable standard dimensions as per site and

Engineer In charge direction, complete with 19-inch mounting frame, minimum 24U usable

height, front toughened glass/acrylic lockable door, lockable rear door/panel, removable

and lockable side panels, cable entry provisions at top and bottom, adequate ventilation

with provision for fan mounting, adjustable mounting rails, equipment mounting hardware,

earthing provision, and all necessary accessories including fixing hardware, cable

management, and installation complete in all respects as required for housing active and

passive networking equipment, including testing and commissioning.

Supply, Installation, Testing & Commissioning of 24-Port Layer-2 Managed Gigabit Ethernet

Switch comprising 24 × 10/100/1000 Mbps RJ45 ports and 4 × Gigabit SFP uplink ports,

switching capacity not less than 56 Gbps, forwarding rate not less than 41.7 Mpps,

supporting IEEE 802.3, 802.3u, 802.3ab, VLAN (802.1Q), QoS, STP/RSTP/MSTP, IGMP Snooping,

Link Aggregation (LACP), Port Mirroring, DHCP Snooping, Access Control List (ACL), Jumbo

Frames, rack-mountable, complete with power cord, rack mounting accessories,

configuration, testing and commissioning, suitable for structured cabling and LAN

Total Amount 177600.00 435561.00

Total Amount 177600.00 435561.00

Total Amount DSR & NDSR 613161.00

Total Amount DSR & NDSR 613161.00

Digitally signed by MANISH

SCHEDULE OF QUANTITIES: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

S No 2025/ DESCRIPTION QTY UNIT RATE

AMOUNT AMOUNT (A)

DSR (INR) NON-DSR

Providing, laying, testing & commissioning of 'C' class

heavy duty MS pipe conforming to IS 3589/IS 1239

including Welding, fittings like elbows, tees, flanges,

27.7 tapers, nuts bolts, gaskets etc. and fixing the pipe on the

1 wall/ceiling with suitable clamp/support frame and

painting with two or more coats of synthetic enamel

paint of required shade complete as required :

Providing, fixing, testing & commissioning of 15mm dia

27.21 quartzoid bulb type sprinklers of rating 68 degree

centigrade with required accessories :

27.21.1 Pendant type 36 Each 599.00 21564.00

Supplying, fixing, testing and commissioning of butterfly

valve of PN 1.6 rating with bronze/gunmetal seat duly ISI

marked complete with nuts, bolts, washers, gaskets

conforming to IS 13095 of following sizes as required :

Digitally signed by MANISH

Carefully Extending, lowering and repositioning the existing

sprinkler points from the existing fire fighting sprinkler piping

network to suit the revised false ceiling layout, including

providing and fixing required lengths of GI/MS sprinkler

drop pipes (up to 1.5 m average), fittings, socket, nipple,

reducer, clamps, hangers, cutting and threading, refixing

existing sprinkler heads, alignment with ceiling tiles, testing,

commissioning and making the system operational

complete as required and as directed by Engineer-in-

Providing and fixing ISI Marked of approved make Fire

5 Extinguishers complete with all accessories as per

manufacturer's specifications.

a) CO2 gas nozzle type - 9 Litre capacity (IS:15683). 6 NOS 12000.00 72000.00

Mechanical Foam gas cartridge type. 9 Kg capacity

ABC dry powder stored pressure type 6 kg capacity

Total Amount 359292.00

Total Amount 359292.00

Digitally signed by MANISH

SC+A1:H13HEDULE OF QUANTITIES - CCTV

TOTAL TOTAL AMOUNT

TOTAL TOTAL AMOUNT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE

A. CCTV DSR NDSR

Supply, Installation, Testing & Commissioning of 5MP IR IP H.265 Vandal Proof

Dome camera with 2.8 to 12mm Motorised Lens,Smart IR, up to 30M IR

distance,Up to 120 dB WDR (Wide Dynamic Range),3D DNR (Digital Noise

1 MR Reduction),H.265+, H.265, H.264, MJPEG,Corridor mode, Triple streams,3-Axis, Nos 18 7500.00 135000.00

IP67, IK10 Vandal Resistant,Colour: 0.005Lux (F1.4, AGC ON), 0 Lux with

IR,Video Compression H.265+, H.265, H.264, MJPEG,Behavior Detection

Supply, Installation, Testing & Commissioning of Linux-based Network Video

Recorder (NVR) for centralized monitoring, management and recording of

IP cameras from the Control Room, supporting minimum 08 IP camera

channels, with minimum 256 Mbps incoming bandwidth,

H.265+/H.265/H.264 video compression, minimum 02 SATA interfaces for

2 MR HDD, minimum 16 alarm inputs and 04 alarm outputs, 1.5U, 19-inch rack- Nos 6 11500.00 69000.00

mountable chassis, with HDMI/VGA video output, network interface and

USB ports, complete with compatible IP PTZ joystick controller for camera

selection, pan/tilt/zoom and focus control, power supply, required

accessories, configuration, installation, testing and commissioning,

complete in all respects. HDD shall be provided separately.

Supply, Installation, Testing & Commissioning of 4 TB Surveillance Grade

SATA Hard Disk Drive (HDD), 3.5-inch form factor, 7200/5400 RPM as per

manufacturer design, SATA III (6 Gb/s), specifically designed for 24×7 CCTV

3 MR surveillance applications, compatible with Network Video Recorder (NVR), Nos 6 12900.00 77400.00

complete with mounting, formatting, configuration, testing and

commissioning. Approved makes: Western Digital Purple, Seagate SkyHawk,

Toshiba S300 or equivalent.

Digitally signed by MANISH

TOTAL TOTAL AMOUNT

TOTAL TOTAL AMOUNT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE

Supply Installation Testing & Commissioning of 24 inch Full HD LED

monitor including wall mount brackets/ clamps/ desk mounting stand.

6 MR SITC of HDMI cables 10 meters M2M etc all compelte. Nos 6 3500.00 21000.00

upply, Installation, Testing & Commissioning of 6-Port Gigabit Managed PoE

Switch comprising minimum 6 × 10/100/1000 Mbps RJ45 PoE ports

conforming to IEEE 802.3af/at PoE standards, with minimum 90 W total PoE

power budget, suitable for simultaneous power and data transmission to IP

CCTV cameras, supporting VLAN, QoS, STP/RSTP and IGMP Snooping, with

suitable Gigabit uplink port(s), rack/wall-mountable, complete with power

supply, mounting accessories, configuration, testing and commissioning,

suitable for IP CCTV applications, complete in all respects.

Total : A - CCTV 0.00 431400.00

Total Amount 0.00 431400.00

Total Amount 0.00 431400.00

Total Amount DSR & NDSR 431400.00

Total Amount DSR & NDSR 431400.00

Digitally signed by MANISH

FIRE ALARM SYSTEM WORKS

S.NO. DESCRIPTION UNIT Qty RATE Amount

INTELLIGENT FIRE ALARM SYSTEM

Supplying, installation, testing & commissioning sector panel suitable for following

zones, complete with visual indications for short circuit fault, open circuit fault, fire

a) 28.1.9 condition and all other standard facilities as per IS:2189 with mimic diagram

for all area/zone covered, complete with all connections, interconnections as

Supplying, installation, testing & commissioning of smoke detector with built in LED

and Mounting base complete withb all Connections etc. as required.

Supplying, installation, testing & commissioning of manual call boxes of MS

28.1.3 construction in Surface/ Recess with Stainless Steel chain & hammer Assembly Each 6 513.00 3078.00

complete with glass and push button etc. as Required.

Supplying, installation, testing & commissioning of response indicator on

d) 28.1.5 surface/recessed MS Box having two LED, metallic cover complete with all Each 18 222.00 3996.00

connections etc as required.

Supplying, installation, testing & commissioning of Fire alarm Sounder with Facility

to make annoucement, mountedc in M.S Box (16 SWG) with Hinged cover plate &

Suitable for operation with Amplifier i/c line matching transformer etc complete as

Supply, Installation, Testing & Commissioning of LED Exit Signage, Single Side,

3W–5W, wall mounted, 230V AC, inbuilt Li-ion/Ni-Cd battery backup (minimum 180

minutes), complete with fixing accessories and connection from nearest lighting

CABLING & WIRING

Digitally signed by MANISH

S.NO. DESCRIPTION UNIT Qty RATE Amount

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable,

600/1000V rated with annealed copper conductor having

XLPE insulation, steel wire armouring & FRLS/HFFR outer

sheath complete as required.

Total Amount 283494.00 33000.00

Total Amount 283494.00 33000.00

Total Amount DSR & NDSR 316494.00

Total Amount DSR & NDSR 316494.00

Digitally signed by MANISH

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle BOard of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle BOard with 2mm thk pvc edge

banding. The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x

1 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter & Nos 6 45500.00 273000.00

one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle BOard and rest all storage to be made out of 18mm thick pre laminated particle BOard. Provision

of Junction BOx, wire raceway and 6 module fliptop BOx for wire passing or as per site

requirement.Main Table Dimension (L)2100mm X (D) 900mm X (H)750mm overall Side Runer

Dimension (L)900mm X (D) 400mm X (H) 675mm

Supplying and placing in position of Back Storage as per photograph/drawing .The back storage shall be

made out of 25mm thick pre -laminated particle BOard of approved shade. The working and non working

2 Back Storage edges shall be finished with machine pressed with 2mm PVC egdge banding. Back Storage Dimension Nos 6 23500.00 141000.00

Supplying and placing in position of 360 degrees revolving high back chai. The chair of Size :-

(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

EBO High Back with leatheritte and cut foam. The chrome plated loop armrest with padded upholstery is provided for

Chair extra comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of

10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/

2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm X

(H)990mm.A contemporary design with an all black finish, . Material & subtype:Premium Leatherette,

EBO Visitor Back Colour & Colour Family:Black, Dimension(W)610mm X (D)505mm X (H)990mm, Back Type:Cantilever,

4 Base:Cantilever Frame, Base Type: Cantilever, Maximum Seating Height:19".The Seat & back are made Nos 12 9500.00 114000.00

up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam

of density 32-35 kg/m3. The backrest has a foam of 28kg/m3.

Providing, supplying and placing in position 3-Seater Sofa, modern design, overall size approximately

2000 mm (L) × 750 mm (D) × 710 mm (H) with seating height approximately 410 mm, having frame

made of seasoned Steam Beech solid wood, upholstered with premium-quality Leatherette of approved

colour, shade and texture. Seat cushion shall comprise multi-layered foam of density 32–35 kg/m³ with

3 seater sofa 2.75" and 1.75" elastic webbing support, and backrest shall comprise 28 kg/m³ foam with 200 GSM

6 EBO Cabin/ polyester polyfill. Upholstery shall be stitched using BOnded nylon thread and provided with stainless Nos 6 42000.00 252000.00

Reception steel legs in matte finish. The sofa shall be complete in all respects including all materials, hardware,

fixing accessories, transportation, loading/unloading and placement at site, as per approved

sample/design and instructions of Engineer-in-Charge.

Digitally signed by MANISH

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle BOard of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle BOard with 2mm thk pvc edge

banding. The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x

1 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter & Nos 6 45500.00 273000.00

one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle BOard and rest all storage to be made out of 18mm thick pre laminated particle BOard. Provision

of Junction BOx, wire raceway and 6 module fliptop BOx for wire passing or as per site

requirement.Main Table Dimension (L)2100mm X (D) 900mm X (H)750mm overall Side Runer

Dimension (L)900mm X (D) 400mm X (H) 675mm

EBO Cabin/ Supplying, and placing in position of Cofee/ Corner Table as per approved design Dimension(L)450mm

Reception X (D)450mm X (H)450mm

Supplying, and placing in position of Centre Table as per approved design Dimension(L)1150mm X

8 Centre Table Nos 6 16500.00 99000.00

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle BOard of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle BOard with 2mm thk pvc edge

banding. The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x

9 Manager Table 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter & Nos 6 38790.00 232740.00

one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle BOard and rest all storage to be made out of 18mm thick pre laminated particle BOard. Provision

of Junction BOx, wire raceway and 6 module fliptop BOx for wire passing or as per site requirement.

Main Table Dimension (L)1500mm X (D) 900mm X (H)750mm overall Side Runer Dimension (L)900mm

Digitally signed by MANISH

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle BOard of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle BOard with 2mm thk pvc edge

banding. The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x

1 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter & Nos 6 45500.00 273000.00

one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle BOard and rest all storage to be made out of 18mm thick pre laminated particle BOard. Provision

of Junction BOx, wire raceway and 6 module fliptop BOx for wire passing or as per site

requirement.Main Table Dimension (L)2100mm X (D) 900mm X (H)750mm overall Side Runer

Dimension (L)900mm X (D) 400mm X (H) 675mm

Dimension: 1200mm(L) X 600mm(D) x 1050mm(H) Supplying, and placing in position of linear

workstation as per Image.The worktop made out of 25mm thk. Prelam Particle BOard with 2 mm thk

PVC edge banding.The Table top supported on Mild Steel of size 50mm x50mm Slanted Leg and 50mm x

25mm Horizontal connectors with Powder coting of 50 Micron.Middle Leg :- 0.8 mm thk Metal panel fixed

on BOth side of the "T" leg for Vertical wire carrying purpose.(Sharing Workstation). 0.8 mm thk

Single/Double metal powder coated raceway with Powder coting of 50 Micron below top for

wiring.Vertical wire carrying pole with powder coating 50 micron below top for wiring( Non- sharing

Linear workstation ). Also having a provision of ms perfoated sheet hanging modesty. provision of glass divider

Workstation rest on the "D" brackets on the table top between opposite seatings. All working or non working edges

shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot

temperature. Provision of pullout PVC keyBOard tray and CPU trolley for each seating.

Also a provision of Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a combination of 2

drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick prelaminated

Particle BOard with provision of handles & Locking arrangement

Providing and fixing printer table of size 1500 mm × 750 mm (5' × 2.5') made from 18 mm thick pre-

laminated particle BOard (BOth side laminated) of approved shade and make, including top, sides,

17 Printer Table modesty panel, shelves as required, edge banding with 2 mm PVC edge tape on exposed edges, Nos 6 11500.00 69000.00

necessary screws, fittings, hardware, level adjustment arrangement, laBOur, handling, transportation

and complete installation as per approved design and direction of Engineer-in-Charge.

Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) Modular Workstation With Side Top

with 3 drawer Pedestal Size 1500W x 600D x 750/1200H.Partition NI-60mm Partition Ht. 1200mm,

Double Raceway systems Skirting label and below the table top . lower tile BOth side laminated and

Modular upper tile inside side fabric, White BOard and white Tinted Glass . With Side Top Size 900W x 400D x

18 750H 25mm thick Gabel end 18mm thick MDF BOard., and 3Drawer top supported Pedestal unit Nos 12 38000.00 456000.00

Size 400W x 400D x 725H made in 18mm thick..Complete Made in MDF BOard.. Laminate 1- Frosty

White, Laminate2 For drawer Facia-Honkong Blue, Fabric-F 161 Dolphin Blue, Powder Coating-

Munshel Gray. and White Tinted Glass

Digitally signed by MANISH

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle BOard of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle BOard with 2mm thk pvc edge

banding. The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x

1 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter & Nos 6 45500.00 273000.00

one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle BOard and rest all storage to be made out of 18mm thick pre laminated particle BOard. Provision

of Junction BOx, wire raceway and 6 module fliptop BOx for wire passing or as per site

requirement.Main Table Dimension (L)2100mm X (D) 900mm X (H)750mm overall Side Runer

Dimension (L)900mm X (D) 400mm X (H) 675mm

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size :-

(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

19 Workstation/ Nos 30 8500.00 255000.00

with leatheritte and cut foam. The chair shall be provided with pneumatic height adjustment which shall

have stroke of 10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of

density 30-35 (+/- 2kg /m3) The backrest has a foam of 28kg/m3.

Providing & Installation of Pantry table of size 1.2m x 0.75m x 1.05m (ht) made out of 19mm thk.

Commercial BOard finished in Recon veneer and DU Pont Coreanof approved shade as per design. The

20 Pantry Table Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided aBOve Nos 6 24500.00 147000.00

table. One (1) number Drawer pedestal with 3 drawers to be provided under the table.

Providing & Installation of Reception table of size .75Dia X 0.75m (ht) made out of 19mm thk.

Commercial BOard finished in Recon veneer and DU Pont Coreanof approved shade as per design. The

21 Reception Table Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided aBOve Nos 6 26500.00 159000.00

table. One (1) number Drawer pedestal with 3 drawers to be provided under the table.

Providing & Installation of Pantry chairs of required dimension and as per instruction of EIC

22 Pantry chairs Nos 12 3700.00 44400.00

The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back panel is made

Openable of 09mm thick MDF of approved shade. All the edges of storage surface shall be provided with machine

Shutter storage pressed imported PVC lipping glued with hot melt EVA glue free from any VOC with free groove handle

and suitable lock. All exposed area PVC edge lipping

Size as decided by site engineer/Bank Sqm 30 18500.00 555000.00

Pantry Under Counter Storage, made with HDHMR BOard finished with laminate on all exposed surfaces.

Unit depth: 600mm. All edges shall be finished with matching edge banding. Includes shutters, shelves,

hardware (hinges, handles), and necessary fittings complete in all respects.

Pantry/ Pantry Overhead Storage Unit, made from HDHMR BOard of approved shade and grade conforming to E1

Workstation norms, with unit depth of 400mm. All exposed edges finished with 2mm PVC edge banding using

Overhead hotmelt EVA glue. Includes shutters, shelves, and necessary hardware and fittings, complete in all

Storage respects.

Digitally signed by MANISH

Sno. Item Specifications Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out

of 25mm thick pre -laminated particle BOard of approved shade. The working and non working edges

shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be supported

with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The

front modesty are made out of 18mm thick prelaminated particle BOard with 2mm thk pvc edge

banding. The table shall be provisioned with Side unit of overall size: 900mm(L) x 450mm(D) x

1 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter & Nos 6 45500.00 273000.00

one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle BOard and rest all storage to be made out of 18mm thick pre laminated particle BOard. Provision

of Junction BOx, wire raceway and 6 module fliptop BOx for wire passing or as per site

requirement.Main Table Dimension (L)2100mm X (D) 900mm X (H)750mm overall Side Runer

Dimension (L)900mm X (D) 400mm X (H) 675mm

3 Drawer top supported pedestal unit size 400W X 400D X 725 H made in 18mm thick complete made in

26 Mobile Vanity MDF BOard. Nos 6 8800.00 52800.00

Total Amount for Furniture 3434940.00

Total Amount for Furniture 3434940.00

Digitally signed by MANISH

S.No Description Unit Qty. Rate Amount

LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120 lm/Watt ) Supplying, Installation, Testing &

Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD type of following body

material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with

Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -50C to

400C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80,

UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical circuitry),

of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K /4000°K / 5700°K /

1 8.1 6500°K (As per ANSI Bin), SDCM (Standard Deviation Colour Matching) <3, Maximum power consumption should not

more than the specified rating and Fixture shall be confirming to relevant BIS standards. Manufactures Word Mark/

Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5

sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5

year OEM warranty. System lumen efficacy ≥105 and <120 lm/Watt output . LM79 & LM80 Test report and all testing

required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-

Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction

temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim

LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt) Supplying, installation, Testing & Commissioning of

Panel light 2x2 ft., of following body material and construction as per IS : 10322 with driver as per the requirement

with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to

40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80,

UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry),

of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K

/6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not

more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name

Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq.mm

FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year

OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED

fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-inCharge as per

requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not

rise above 90°C). Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm)

Total Cost of Light items 352134.00

Digitally signed by MANISH