Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
₹49.1 L
EMD Value
₹50,000
Closing Date
20 Nov 2026, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Executive Engineer, U.L.B.C.Inv.Dn.No.2,Valod
Renovation work of Section Office Building and Construction of Compound wall At Ukai Ta-Ukai Di-Tapi
364271
E Tender Notice No.11 of 2026-27
Open
Civil Works
Works
Tapi
13 documents required · 11 mandatory · 2 optional
₹1,500
Executive Engineer, U.L.B.C.Inv.Dn.No.2,Valod
₹50,000
6 Nov 2026
6 Nov 2026
6 Nov 2026
20 Nov 2026
6 Nov 2026
120 days
22 stuff and depositing on the road side slope as directed up to 50 200.55 Cum 106.65
Construction of Granular sub-base 150 mm thick by providing
coarse graded machine crushed B.T.material satisfying MOST
specification of grading I (B.T.stone aggregate 53 mm to
mm 35%,26.5 to 4.75 mm-45% and 2.36 mm below-20%)
including spreading in uniform layer with motor grader on
23 prepared surface,mixing by mix in place method with rotavator 181.51 Cum 861.53
at OMC and compacting with vibratory roller to achive the
desired density etc.complete As per RA
Providing and fixing pre-cast concrete kerb stone of gray
cement based concrete block 30cm length,30cm height and
15cm thick of M200 grade concret as per approved design and
24 including excavation for fixing in proper line and level,filling 59.00 Rmt 392.96
the joint with C:M 1:3 (1cement:3fine sand) etc complete.
(B) Providing sock pit of 5.00 Cu.M. Volume including
excavating and filling brickbats with dry masonry work at top
for 45cm. height including covering the top with stone
including providing vatas in C.M. 1:3 with finishing curing
etc. complete as directed.
Excavation for foundation upto 1.5 m depth including sorting
out and stacking of useful materials and disposing off the
excavated stuff upto 50 Meter lead.(A) Loose or soft soil
Providing and laying cement concrete 1:3:6 (1-Cement : 3-
coarse sand : 6- hand broken stone aggregates 40 mmnominal
27 size) and curing complete excluding cost of formwork in (A) 30.00 Cum 3080.90
Foundation and Plinth
Providing and laying cement concrete work 1:2:4 (1- Cement :
2- Coarse sand : 4- graded stone aggregates 20 mm nominal
size) and curing complete excluding cost of formwork and
reinforcement for reinforced concrete work in (B) Slabs,
landing, shelves, Balconis , Lintels, Beams, Girders and
Cantilever upto floor two level.
Providing & Laying Controlled cement concrete M-200 and
curing complete excluding the cost of form work and
reinforcement for reinforce concrete work in (A) Foundation,
29 footings, Base of Columns and Mass Concrete (Footing) for 15.40 Cum 4098.94
road. (R&B SOR 2024-25,It.Code 05024AA,p.no:77).
Labour charges for giving Trimix treatment to Concrete
surface including necessary steel channel formwork and
required tools and machinery including preparing joint with
concrete cutter machine as required and directed. (As per RA)
Providing TMT Bar FE 500D reinforcement for R.C.C. work
31 including bending, binding and placing in position complete 726.94 Kg 77.29
upto floor two level
Providing and fixing water closet squatting Pan (ORISSA
PAN) approved make like cera/jaquar/Simpolo/Hindware or
32 equvalent to same of size 450*585*255mm (I) Long pattern = 1.00 Each 2020.00
White colour.(MR)
Providing and fixing Wall Hung-WC with PP normal closet
seat cover, hinges, accessories set approved make like
cera/jaquar/Simpolo/Hindware or equvalent to same of size
370*535*405mm with integral P or S trap including jointing
the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-
fine sand) (i) in white colour(MR)
Providing and fixing Hand shower (Health Faucet) with 8mm
dia 1.2 meter long flexible tube and wall hook of approved
34 make like cera/jaquar/Simpolo/Hindware or equvalent to 1.00 Each 1515.00
Providing and Fixing 100 mm size P or S trap for water closet
squatting pan including jointing the trap with the pan and soil
35 pipe in cement Mortar 1:1 (1 cement : 1- fine sand) (A) 1.00 Each 337.52
vitreous china.
Providing and fixing Urinal or approved quality including
conecting the Urinal with waste pipe ,Down tap etc.
complete.approved make like cera/jaquar/Simpolo/Hindware
or equvalent to (A) White earthenware flat back or corner type
size 430mm x 260mm x 350mm.(MR)
Providing and Fixing plastic seat and cover for wash down
water closer with C.P. brass hinges and rubber buffers. (B)
black plastic seat and cover.
Providing and fixing wall hung basin with fixing accessories
set with single hole for pillar tap approved make like
cera/jaquar/Simpolo/Hindware or equvalent to same of size
550*400*195mm In white colour.(MR)
Providing and fixing screw down bib taps of following
39 size.(B) Brass chromium plated screws down Bib Tap. (i) 2.00 Each 186.83
Providing and fixing chromium plated brass half trun flush
40 cock of approved quality including fixing in pipe line etc. 2.00 Each 263.77
complete.(ii) 25mm dia.
Providing and fixing C.P. brass waste for washbasin or sink.
Providing and fixing M.I. fisher union for washbasin or sink.
Providing, laying and jointing in true line and level
diametre U.P.V.C (Type B) conforming to IS 13592-1992
with one end plain and other end socketed with rubber ring, &
fittings conforming to ISI 14735- 1999 of approved make for
drainage system pipe line, pipe shall be jointed with each other
with rubber lubricant, pipe shall be fixed on wall using of PVC
clamp of the size 110 mm diametre x 149 mm length x
mm heigh at every 2000 mm center to center or shall be
concealed in walls as directed including necessary fittings such
as bends, shoes etc. including testing of pipes and joints and
jointed with adhesive solvent cement including cost of all
Providing, laying and jointing in true line and level 75 mm
diametre U.P.V.C (Type B) conforming to IS 13592-1992
with one end plain and other end socketed with rubber ring, &
fittings conforming to ISI 14735- 1999 of approved make for
drainage system pipe line, pipe shall be jointed with each other
with rubber lubricant, pipe shall be fixed on wall using of PVC
clamp of the size 110 mm diametre x 149 mm length x
mm heigh at every 2000 mm center to center or shall be
concealed in walls as directed including necessary fittings such
as bends, shoes etc. including testing of pipes and joints and
jointed with adhesive solvent cement including cost of all
materials. (RA)
Providing and fixing concealed center point to wall ceiling &
floor CPVC (SDR 13.5) PIPE having National Sanitation
Foundation (NSF) seal for potable water of following dia.
45 nominal bore tube fittings and clamps including making good 20.00 Rmt 170.36
the wall, ceiling and floor etc. complete. [A] 15 mm.
(B)20mm nominal outer dia pipes (item Code:23056, Pg.
(C)25 mm nominal outer dia pipes (item Code:23057, Pg. no.
(D)32mm nominal outer dia pipes (item Code:23058, Pg. no.
Providing and fixing brass screw down stop tap. (A) 15mm
Providing and fixing ball cock of approved quality as directed.
47 (A) Copper Metal (ii) 50mm dia. 2.00 Each 189.84
Providing and fixing chromium plated brass half trun flush
48 cock of approved quality including fixing in pipe line etc. 3.00 Each 275.76
complete.(iii) 32mm dia.
Providing and fixing Gun metal check or non-return fullway
wheel valve.(D) 32mm dia.
Providing erecting and fixing double coated Syntex PVC. (ISI)
water tank of required capacity each with all necessary fittings
and connection etc. complete on terrace.
Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire
of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade
FRLS PVC insulated multi strand copper wires up to 10 mtr
length , in below type of pipe erected with 6A Modular type
switch / bell push & accessories and earth continuity of
following type, erected on PVC / Metallic/Wooden box, single
mounting base frame covered with textured/metallic/white
front plate modules erected on / in wall / ceiling as per pipe
51 erected, with necessary Lamp holder/ceiling rose / 16.00 Pt. 488.84
H.D.Connector as directed.
(c) with oval conduit /PVC casing capping double lock type
erected flushed on wall/ceiling complete
Point wiring for FAN with 2-1.5 sq.mm & earth wire of
sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS
PVC insulated multi strand copper wires up to 10 mtr length,
in below type of pipe erected with 6A Modular type switch
and hum free EME four or more step type electronic fan
regulator with separately mounted and accessories with earth
continuity of following type erected on PVC /
Metallic/Wooden box, single mounting base frame covered
with textured/metallic/white front plate modules erected on /
in wall / ceiling as per pipe erected. with necessary ceiling rose
/ H.D.Connector as directed.
(d) partial PVC pipe and drops in oval conduit / PVC casing
capping erected flushed on wall/ceiling complete
Point wiring for Tissino / Modular secondary light point with
2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of
ISI marked 1.1 kV grade FRLS PVC insulated multi strand
copper wires, in below type of pipe to be erected complete
with earth continuity and necessary connection with primary
light with accessories erected on Metal / PVC / wooden box
covered with 3 mm thick PC(Polycarbonate) / Acrylic sheet
53 for open / concealed wiring. with necessary Lamp holder / 17.00 Pt. 133.32
ceiling rose / H.D.Connector as directed.
(c) with oval conduit /PVC casing capping double lock type
erected flushed on wall/ceiling complete
Point wiring for on board Looped Plug with 6A Modular
type switch & 5 pin socket erected on PVC / Metallic/Wooden
box, single mounting base frame covered with textured /
metallic/white front plate modules erected on / in wall /
ceiling with following type accessories.
Providing following type of Modular Type Accessories
mounted with PVC / metallic/Wooden box, single mounting
base frame covered with textured / metallic/white front plate
55 modules erected with necessary connections as per site
situation directed by Engineer In charge.
(7) Blank Plate Single Cat.III 10 Each. 25.25
(9) 16 Amp. SP one way switch Cat.III 10 Each. 180.79
(10) 6/16Amp. Universal socket Cat.III 10 Each. 199.98
(15) 32 Amps. DP switch with Indicator Cat.III
Decorative call bell Ting-tong box type 250 volts complete
Providing and erecting ISI mark Medium class RIGID PVC
PIPES of following size complete to be erected on/in wall or
ceiling erected with necessary PVC fittings & Junction boxes
fixed with adhesive solution & Clamps with following dia of
pipes, in approved manner as directed .
Providing and erecting Mains with 1.1 KV grade FRLS PVC
insulated ISI marked stranded Copper conductor wire in
following type of pipe to be erected concealed in /flushed on
wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC
insulated stranded wire of green colour for earth continuity of
58 following size. 100 Mtr. 104.03
(C) With oval conduit /PVC casing capping double lock type
(b) 2 wire 2.5 sq. mm
Providing and erecting Mains with 1.1 KV grade FRLS PVC
insulated ISI marked stranded Copper conductor wire in
following type of pipe to be erected in / on wall / ceiling with
2.5 sq. mm copper conductor FRLS PVC insulated
stranded wire of green colour for earth continuity of
following size.
(C) with oval conduit /PVC casing capping double lock type
(a) 2 wire 4 sq. mm
(b) 2 wire 6 sq. mm 80 Mtr. 170.69
Providing and erecting Mains with ISI marked, 1.5KV grade
electrolyte multi stranded, annealed copper conductor with
heat resistant PVC insulated conforms to IS 694, IEC -
erected in existing pipe of following size (Specifically for
control panel, relays, power switchgears, motor starters &
control wiring) with required size of copper lugs, nuts and
bolts if required.
(e) One wire 6.00 sq. mm
(f) One wire 10.00 sq. mm 50 Mtr. 115.14
Providing & erecting main Distribution (MDF) indoor type,
back mounted frame as per DoT standard approved with krone
strips (c) Suitable for 50 pair
Supplying and erecting LED indoor fittings with LEDs of
wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,
with housing used as a heat sink shall be made of thick sheet
Steel conforming to IS: 513/CRCA/ aluminium die cast
powder coated and high U.V. & corrosion resistance with
diffuser with company mark/name 120 to 300 V,Power Factor
more than 0.9, THD < 15 %,CCT 3000 K to 6500K,
Luminaire efficacy> 85 lumens/watt ,LED efficiency-110
lumens/watt LED driver efficiency > 85 %
CREE / OSRAM / PHILIPS Lumileds / NICHIA /
SEOUL/Bridgelux make LED used for luminaire. ( fitting
required LM-79 & LM-80 Certificates)(NOTE: Below
description have shown ranges of Wattage capacity of LED
fittings.The Engineer incharge may select any wattage capacity
between the ranges shown.)
(A) Square/ Circular shaped Surface/Recessed Mount
Downlight with provision for spring loaded mounting clips
(iv) 22-24 watts, Surge-2 KV
(B) LED Panel Light with provision for Plane front frame with
translucent cover fixed to housing complete.IP20 (v) 24 watts,
63 12" x 12" , Surge-2 KV 4 Each. 724.17
Providing and erecting Approved make Ceiling fan with
double ball bearing ISI mark with condenser A.C. 23OV.50
c/s.1200 mm. sweep complete, canopy erected on existing
hook or clamp with earthing. [Make shall be approved by
Engineer in charge]
Supplying and erecting 19 / 20 mm. nominal bore Medium
Class M.S. Pipe down rod erected duly painted for fan
complete with proper insulation without leakage and earthing.
Supplying & erecting fan hook box of 10 mm M.S. round
bar bounded to the RCC bars up to 50mm length each side
and pierced through a 16 Gauge M.S. box / Heavy Duty PVC
box complete erected concealed in Ceiling with necessary
Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured
cable multistrand Aluminium conductor for 1.1 KV. to be
laid on wall with necessary clamps or in existing trench / pipe
67 of following size of cables 20 Mtr. 341.38
(C) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core)
(D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)
Providing and, fixing heavy duty flange type brass double
compression type cable gland with rubber ring for PVC
insulated armoured cable complete with out going tails,
insulating tape etc for following size of cables.
(B) 3 & 1/2 core 35/50 Sq. mm
(C) 3 & 1/2 core 70 Sq. mm 5 Mtr. 103.02
Solder less crimping type Aluminium lugs conforming to IS
suitable for cable of following size evenly crimped with high
pressure tool & connected to switchgear terminals with
brass/cadmium plated nut bolts in an approved manner.
(E) 70 Sq.mm. 5 Each. 25.25
Making trench in soft soil of suitable width of 90 cm deep for
laying cable or locating the fault all over the run and back
filling the same and making the surface as normal ground.
Providing & laying approved make Double walled
corrugated pipes (DWC) of polyethylene(conforming to IS
14930 II )with necessary connecting accessories of same
71 material at required depth in existing trench for laying of 50 Mtr. 95.95
cable. below ground / road surface for enclosing cable (C))90
Providing and erecting Miniature circuit breaker single pole
6A to 25A suitable to operate on 240 V A.C. system and
having breaking capacity 10 KA to be erected in existing box.
confirming to IS 8828/1996 with ISI Mark
Providing & erecting 240 V MCB double pole switch for
lighting Load (B Curve) having 10 KA breaking capacity &
confirms to IS : 8828 in existing box having following
Providing and erecting Approved make ELCBs / RCCBs
conforming to IS: 12640 and having sensitivity of 30 mA and
Short Circuit withstand capacity of 10 KA and suitable for
operation on single phase 240 V,50Hz. having characteristic of
quick action & tripping with all advance feature & do not
74 incorporate any electronic component. for following Max. 1 Each. 2458.34
rating erected as directed.
(ii) 40Amps. DP
Providing & erecting 415V MCB Four Pole Switch for
Lighting Load (B curve) having 10KA breaking capacity &
confirms to IS :8828 in existing box having following
Providing and erecting Approved make Four pole moulded
case circuit breaker having breaking capacity ICU of 25 KA.
at 415 V,having normal current rating up to 25 A to 100A.
with Fixed thermal & magnetic release suitable to work on
76 A.C. supply 50 c/s. with all internal connections & complete 1 Each. 6790.23
erected in existing 16 G.M.S. housing.
ICS=100% of ICU only Cat III
providing and erecting Approved make Four pole moulded
case circuit breaker having breaking capacity ICU of 35 KA.
at 415 V. having normal current rating 125A. with Fixed
thermal & magnetic release suitable to work on A.C.supply
77 50 c/s. with all internal connections & complete erected in 1 Each. 8861.74
existing 16 G.M.S. housing.
ICS=100% of ICU only Cat III
providing and erecting Approved make Four pole moulded
case circuit breaker having breaking capacity ICU of 35 KA.
at 415 V. having Normal current rating 200A.with variable
Thermal & magnetic release suitable to work on A.C.supply
78 50 c/s. with all internal connections & complete erected in 1 Each. 17843.67
existing 16 G.M.S.housing
ICS=100% of ICU only Cat III
Supplying and erecting triple pole & neutral 440V / 500V
panel mounting Copper Busbars with four equal Nos. of
electrolyte bus having current density not more than 1.6 Amp.
/ sq.mm (Rated current / cross section area) duly wrapped with
colour insulating tape for phase sequence of following current
carrying capacity, erected with necessary bus bar supports
/insulators, main cable socket to each bar, erected in existing
cubical panel with necessary connections.
(A) Suitable for 100 Amp. Capacity
(B) Suitable for 200 Amp. capacity 1 Mtr. 3202.71
Providing & erecting weather proof, dust & vermin proof, Sq.Mtr
floor mounted front operated indoor type cubical panel board
necessary IP-42 and above protection as per approval from
engineer incharge made from 14 SWG thick CRC M.S. sheet
for outer body & doors, 16 SWG thick CRC M.S.sheet for
internal partitions with necessary accesories , supporting
angles/ flats channel including cutting, bending, drilling,
welding, riveting with internal partitions & cable alley as per
requirements & instruction of engineer-in-charge with erection
of supplied switch gears, BUSBARS, suitable size of inter
connecting PVC copper wire / copper-aluminium strips, rubber
grommets, rib, bakelite control fuses/MCB for measuring
instruments, earth bus & earth bolts, foundation flange - bolts-
base Plates, sufficient nos. of hinged doors, handles with
locking arrangement and rubber gasket,heavy duty end
terminal connection,danger notice board,necessary
ventilation,earthing strip complete. The Panel shall be painted
with epoxy powder coating.(The rates excludes the cost of
switchgears, bus bars, inter connecting mains & Copper
Aluminium strips, meters, Fuses etc. The dimension shall be
measured excluding base beams) The panel shall be supplied
with following approved manufacturers with following size.
(A) locally fabricated panel board
(i) with 350mm depth
Supplying and erecting approved make suitable panel indicator
lamps of LED type lamp, lens cover, Bakelite holder complete
erected with necessary connections.
Supplying and erecting approved make panel mounting type
Digital Voltmeter having 3 digits LED display, 0 to 750 AC
Volts range erected on existing panel board with all
connection, wiring etc .with manufacturers calibration
Supplying and erecting approved make panel mounting type
Digital Ammeter having 3 digits LED display, external CT
operated, calibrated for 0 to 1000 Amps suitable to operate on
83 500 Volt AC , erected on existing panel board with all 1 Each. 1558.43
connection, wiring etc .with manufacturers calibration
Supplying and erecting Ammeter / Voltmeter selector switch
for 3 phase AC Supply 500 V on existing panel board with
necessary connections.
Providing & erecting Medium Voltage Danger Notice Board
sticker as per language suggested by engineer incharge of
standard size as per IS-2551
Providing and erecting Sheet Steel powder coated MCB
distribution board - flush / surface mounted fitted with busbar,
neutral link, earth bar and DIN rail, Conforms to IS 8623-1 &
3, IEC 61439-1 & 3 without MCB to house appropriate nos. of
MCBs.(The DBs should be used of same company of MCB to
86 be used) suitable for 1 Each. 1492.78
(A) single phase incoming and horizontal single phase
outgoing (b) sheet steel double door (IP-43) (iv)12 way
Supplying & erecting earth pit of minimum bore dia.150mm
size approved make Earthing Electrode consisting Pipe-in-
Pipe Technology as per IS 3043-1987 made of corrosion free
hot dipped G.I.Pipes having Outer pipe dia of 50mm having
80-200 Micron galvanising, Inner pipe dia of 25 mm having
200-250 Micron galvanising, connection terminal dia of 12mm
with constant ohmic value surrounded by highly conductive
compound with high charge dissipation suitable for following
type of applications with chamber and heavy duty
cover.(approved make OEM has to submit test certificate) &
having back filling compound of (B) Inner chemical (CCM
Compound)- Resistivity:- 0.2 / meter testing as per IEC
87 62561-2017, Voltage drop:- < 1 volt at no load & dry form, 2 Each. 4591.46
Sulphar content:- <2%(C) Back fill Compound :- Earthing
compound should be capable to retain moisture for long time
Necessary test report must be submitted.
(a) For Electrical Installation up to 440V in normal soil
Length of pipe - 1 Mtr
Back filling compound - 1 Nos Bag of 15 Kg.
Providing and erecting Annealed bare Copper wire 8 to
Providing , erecting , fabricating the M.S. structure as per
requirement on site incorporating proper size of M.S.
angles,square,round, flats, bars, channels, sections complete
with cutting, welding, grinding & finishing duly painted with
89 one coat of red oxide with erection on site as per direction of 20 kg 77.77
engineer in charge with necessary grouting, cementing,
plastering & finishing complete.
Providing and erecting water cooler having storage capacity
80Ltr. & cooling capacity 40 Ltr.per hour @ an ambient temp
of 45˚ C. The outlet temp. of the water should drop by 15˚ C
within a hour, The water cooler should be comprising of
hermetically sealed compressor, fan motor, condensing unit,
90 water tank surrounded by evaporating coil, thermostats, relay 1 Each. 54515.76
etc. complete with necessary inlet & outlet connection. The
body of water cooler will be made from Stainless Steel. and
Supplying & erecting reverse osmosis (RO) water
purification system with M.S. powder coated pedestal frame,
prefilter housing carbon filter suitable buster DC pump, auto
low & high pressure switches with following size of LPH
capacity & erected as directed with one year comprehensive
maintenance guarantee.
[D] 100 LPH with 3 phase Raw water pump of 500LPH @
2.5kg/cm2 - (1N0 - Kirloskar /CRI/Lubi), Dual media filter
91 10"x54" - (1 No), Micron cartridge filter 20" x 2.5" ( 1No), 1 Each. 77891.20
High pressure pump 500LPH @ 10kg/cm2 - (1No - Shimge
/CRI /Lubi), RO Membrane housing with RO membrane of
40*40 - (1No), RO pressure tube 4" x 1E - ( 1No), 0 -
1200LPH Rotameter -(2 Nos), with Recovery Rate 50%.
Supplying and erecting Flexible PVC insulated multi strand
multi core 1.1 kv grade ISI marked copper wires of following
92 size to be erected as directed. 60 Mtr. 58.58
e) 1.50 Sq.mm 3 core round PVC sheathed.
Make:Finolex,Polycab,Havell's,KEI,L&T
Supplying and erecting approved make Octagonal pole made
from HR sheet steel. The pole should be made as per IS. and
shall be coated with hot dip galvanizing as per IS
2629/2633 /4759, suitable suspend local wind speed with
integral Junction box consist of terminal plate of min 6mm
Hylam sheet, standard profile 35mmX7.5mm Din-Rail for
MCB Mounting, stud type terminal and arrangement for
cable termination to be erected on foundation as per details
given by manufacturer considering site requirement.
(B) 4 Mtr. Long 70 mm Top X 130 mm bottom dia, 3 mm
thickness with 200mmX200mmX12mm base plate, 4-M16
Bolts and 450mm long with necessary G.I. J Bolts .Approx 4 Each
(D) 6 Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm
thickness with 200mmX200mmX12mm base plate, 4-M20
Bolts and 600mm long with necessary G.I. J Bolts .Approx 2 Each
Pole weight 59 kg
Supplying and erecting Street light pole bracket comprising
main B Class MS pipe of 4.2 cm/require outside dia. complete
with suitable B Class M.S. sleeve tubing of approx.
45cms.length and suitable for 76.5mm/80mm/require size of
pole top having nuts and bolts for fixing the brackets and
having spread of 0.5 mtr. Length with 110 deg.with vertical
94 plane and suitable welded stiffener reducer and nipple with 6 Each
check nut complete painted with one coat.of Red oxide / PU
base primer and two coats of Aluminium / PU paint. paint with
following nos of arms.
Providing cement concrete. foundation or for concrete
filling in 1:3:6 ratio with 20 to 25 mm stone metal duly
plastered with necessary curing for pole muffing or any other
Flood light fittings with High power White LEDs wattage of
Watt and above assembled on single MCPCB, efficiency more
than 130 lm/w and corrosion free High pressure die cast
aluminum housing with smooth finish powder coated and heat
sink extruded aluminium with diffuser and Polycarbonate
optics/ lenses, with toughened glass with company mark/name
engraved or embossed 160 to 270 V,Power Factor more than
0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio
>0.45, Luminaire efficacy> 100 lumens/watt . LED driver
efficiency > 85 %.( fittings required LM-79 & LM-80
certificates)(NOTE: Below description have shown ranges of
Wattage capacity of LED fittings.The Engineer incharge may
select any wattage capacity between the ranges shown.)
(A) Street Light (IP-65), Surge protection -4KV integral and
,Light must have 440VAC line supply with over-voltage
(iii)60 watts to 90 watts Make-philips,havells,Schneider, lance,
(C) Post Top Lantern LED fitting comprises of Copper
dust finish cast aluminum spigot and spun aluminum
canopy fixed with opal polycarbonate, pipe arrangement
for vertical mounting driver and accessories wired upto
97 terminal block.IP 65 5 Each
(a)20- 30W Make-philips,havells,Schneider, lance, osram
(3) LED Bollard fittings of minimum height 1000 mm &
dia.100mm having polycarbonate clear/milky diffuser
mounted on 3mm thick aluminium finished powder coated
pipe with base plate 160x160mm with erection by M8x75mm
fastner with required RCC foundation.IP65 for 9 to 20 watt
and above ,surge-4kv cat-III Make-philips,havells,Schneider,
Providing and erecting HOT deep Galvanised iron strip
wire 8 to 16 SWG.
Providing and erecting Pipe type earthing having
cms.long and 2.5 cms. dia. galvanised iron pipe with
100 coupling and buch buried in specially prepared earth pit 5 Each
complete with necessary 8 SWG earth wire.
For using salt and charcoal / coke as required for pipe type
providing and erecting Miniature circuit breaker single pole
0.5A to 2A system and having breaking capacity 10 KA to be
erected in existing box. confirming to IS 8828/1996 with ISI
102 Mark Make:Siemens,L&T,Havell's,GE,ABB 10 Each 123.22
Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured
cable multistrand / Solid Aluminium conductor for
KV. to be laid on wall with necessary clamps or in existing
103 trench / pipe of following size of cables 70 Meter 151.5
(b) 4 core 6 Sq. mm
Make:Finolex,Polycab,Havell's,KEI,L&T
Making trench in Hard Murrum / Tar Road of suitable width
of 90 cm or required depth for laying any size of cable or
104 locating the fault all over the run and back filling the same 60 Meter 74.74
and making the surface as normal ground.
Providing & laying approved make Double walled
corrugated pipes (DWC) of polyethylene(conforming to IS
14930 II )with necessary connecting accessories of same
material at required depth in existing trench for laying of
105 cable. below ground / road surface for enclosing cable Make- 60 Meter 62.62
Gemini, Dura-gaurd,Rex
(A)50 mm outer dia
Supplying following size of Light duty “A” Class G.I . Pipe
& erecting as directed by Engineer-in-charge
106 (A) 25 mm dia . 60 Meter 172.71
Supplying & erecting approved make SMC press moulded
composite FRP. loop-in, loop-out approx. 2mm thick box
complete with Bakelite connector strip 5way(3P+N+E),DIN
rail for mounting mob & hinged doors as per requirement
having locking arrangements with mounting clamp with nuts,
107 bolts & washers suitable for erection on pole with cable 5 each 476.72
clamps& earth bolt of following size of box.
( c)150mm x 125mm x 100mm [deep]
Supplying & erecting approved make Digital time switch
having lithium cell 6 years operative and operate battery
backup 1 channel day clock with 14 memory programme,
suitable to operate on 240V + 5%, 16A with, floating contacts
Minimum switching setup time 1 minimum & LCD display.
Also comprised permanent ON/OFF switching. Programming
switches & housed in fire proof thermoplastic enclosure &
transparent cover erected as required with necessary
connection erected as directed.
Supplying & erecting power contactor ,AC3 duty for time
switch complete erected as per direction Cat III
[C] 4 pole 440V 16 Amp.
Clearing and grubbing road land including uprooting rank
vegetation grass bushes, shrubs, sapling and trees girth up to
300 mm removal of stumps of trees cut earlier and disposal of
unserviceable materials (C) By mechanical means in area of
Excavation for foundation upto 1.5 m depth including sorting
out and stacking of useful materials and disposing off the
excavated stuff upto 50 Meter lead.(B) Dense or Hard soil
(Executed with mechanised efforts/Machinaries)
Excavation for foundation upto 1.5 m depth including sorting
out and stacking of useful materials and disposing off the
excavated stuff upto 50 Meter lead. (C) Hard Murrum
(Executed with mechanised efforts/Machinaries)
Providing and laying cement concrete 1:3:6 (1-Cement : 3-
coarse sand : 6- handbroken stone aggregates 40 mmnominal
113 size) and curing complete excluding cost of formwork in (A) 22.3 Cu.M. 3080.90
Foundation and Plinth
Providing and laying cement concrete work 1:2:4 (1- Cement :
2- Coarse sand : 4- graded stone aggregates 20 mm nominal
size) and curing complete excluding cost of formwork and
114 reinforcement for reinforced concrete work in (A) 76 Cu.M. 4061.84
Foundations, footings, Base or columns and Mass concrete
(more than 10 ton)
Providing TMT Bar FE 500/500D reinforcement for R.C.C.
work including bending, binding and placing in position
complete upto floor two level (upto 10 ton)
Providing formwork of ordinary timber planking so as to give
a rough finish including centering shuttering strutting and
propping etc. Height of propping and centering below
supporting floor to ceiling not exceeding 4 M. and removal of
116 the same for in situ reinforced concrete and plain concrete 178.58 Sq.M. 179.36
work in. (A) Foundations Footings Bases of Columns etc. and
Mass concrete. (upto 10 ton)
Providing formwork of ordinary timber planking so as to give
a rough finish including centering, shuttering, strutting and
propping etc. height of propping and centering below
supporting floor to celiling not exceeding 4 M. and removal of
117 the same for in situ reinforced concrete and plin concrete work 185 Sq.M. 311.43
in (G) Columns, Pillars, Posts and struts (1) Square,
Rectangular, Polygonal in plan.
Filling available excavated earth (excluding rock) in trenches.
plinth, sides of foundations etc. in layers not exceeding 20cm.
118 in depth consolidating each disposited layer by ramming and 80.114 Cu.M. 133.65
Brick work using common burnt clay building bricks having
crushing strength not less than 35 kg./Sq.Cm. in foundation
and plinth in Cement Mortar 1:6 (1- Cement : 6 - fine sand)
119 (B) Conventional (upto 10 ton) Extra for brick work in 67 Cu.M. 4403.40
superstructure above plinth level upto floor two level (B)
Providing 20mm thick cement plaster in single coat on single
120 or half brick walls for interior plastering upto floor two level 830 Sq.M. 247.84
and finished even and smooth in (i) Cement mortar 1:3 (1-
Finishing wall with weather proof exterior emulsion paint on
wall surface (two coats) to give an required shape even shade
after thoroughly brushing the surface to remove all dirt and
remains of loose powdered materials etc completed.
Providing and fixing 0.45 Metre high fencing with 0.75 Metre
long M.S. Angle posts 40mm x 40 mm x6 mm and oil painting
3 coats fixed at 3.0 Mt.C/C. with 750mm dia and @ 130mm
C/C circular series of Hot deep galvanised riser tape
122 concertina coil, strained and fixed to posts with RBT (Raiser 160 Rmt. 1435.39
Barbed Tape) with the help of U-nails/split pin, staples
including fixing the posts in C.C. Column.
Providing and fixing M.S. Gates of required pattern fix on
brick walls/Columns prepared with M.S. flats, angles,
123 Square/round bars, square pipes, at required spacings with 11 Sqmt 12289.15
necessary hold fasts as per detailed drawing etc. complete
including applying primer coat and enamel painting two coat.
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
RAW_HTML
12. BOQ.pdf
12.DTP SBD Book Section Office 1165 m - Copy-compressed.pdf
E Tender Notice No.11 of 2026-27.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .