Construction of 2000 M.T. Godown building at Padedi Ador Ta. Santrampur Dist. Mahisagar (Deposit work)

No. Figure Amount

1 Excavation for foundation upto 1.50 mt depth including sorting out and 646.00 Cum 278.06

stacking of useful materials and disposing the excavated stuff within all lead

and lift for soft rock not requiring blasting.

2 Excavation for foundation from 1.50 mt to 3.00 mt. depth including sorting out 290.40 Cum 651.26

and stacking of useful materials and disposing the excavated stuff within all

lead and lift for Hard rock.

3 Filling in foundation and plinth with sand in layers of 20 cm thickness 253.20 Cum 479.80

including watering, ramming and consolidating etc. complete.

thickness including watering, ramming and consolidation etc. complete.

5 Anti Termite System : P/L of Permanent piping technology Anti Termite 1193.80 Sq.m. 63.63

treatment before flooring work by installing LLDP (Low linear density

Polyethylene) tube of 8 mm O.D.& 6.4 mm I.D. with in Built Pressure

Compensation chip every 30 cm interval in the tube, having working pressure

of 2 kg/cm 2 and release rate of 1.9 ltr/Hour fixed by P-Clip and nails. The

LLDP pipe shall be installed at the entire periphery of the building and at

internal network of building depth of 20 to 200 mm under floor every 2 to

mtr. c/c distance (adjustable as per building layout) & ends of loop pass

through a PVC Elbow of minimum 32 mm ID at junction box of wall and floor

level, entering into a steel reinforced grooved flexible pipe mini. 22 mm LD

leading into junction box and during injecting chemicals for termite control

treatment.

The anti-termite chemical Lmidcloprid 30.5% SC mix as per IS 6313 (part-III)

shall be injected by the pressure pump diluted with water @ 10.5 ml/5ltr of

water at the rate of 2 kg/sq.cm. @ 5 ltr /Smt. the contractor shall submit

approved line plan for piping system and junction boxes dully approved by

Engineer-in-charge with bond of 5 years warranty. (II) Anti Termite chemical

injected area (Chemical injecting including labour cost)

6 Providing and laying controlled cement concrete M-150 and curing complete 29.10 Cum 4022.72

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Foundations and plinth for PCC.

7 Providing and laying controlled cement concrete M-250 and curing complete 132.70 Cum 4828.20

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Foundations, footings & mass concrete.

8 Providing and laying cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 163.30 Cum 3092.22

machine cut stone aggregate 40 mm nominal size) and curing complete

including cost of form work in foundation and plinth.

9 Providing and laying controlled cement concrete M-250 and curing complete 58.00 Cum 7617.28

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Columns upto plinth level.

10 Providing and laying controlled cement concrete M-250 and curing complete 4.60 Cum 7658.82

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Columns for Ground floor.

11 Providing and laying controlled cement concrete M-250 and curing complete 169.00 Cum 6398.17

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Ground beam and plinth beam.

12 Providing and laying controlled cement concrete M-200 and curing complete 183.40 Cum 4995.13

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Plinth Slab.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

13 Compaction and finishing of cement concrete road by trimix process 2957.00 Sq.m. 65.65

providing extra labour charges for the trimix vacume dewatering service

process on cement concrete road surface by using vacuum dewatering pump

floater surface vibrator including making grooves and rough finish to surface

including leveling etc. complete.

14 Providing and laying controlled cement concrete M-200 and curing complete 5.10 Cum 6818.31

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Ground floor slab.

15 Providing and laying controlled cement concrete M-200 and curing complete 2.30 Cum 5492.74

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Walls from top of foundation level upto floor two

16 Providing and laying controlled cement concrete M-200 and curing complete 105.80 Cum 6364.82

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Ground floor beams.

17 Providing and laying controlled cement concrete M-200 and curing complete 18.90 Cum 6406.36

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in First floor beams.

18 Providing and laying controlled cement concrete M-200 and curing complete 4.70 Cum 6934.10

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Chhajja at Ground floor.

19 Providing and laying controlled cement concrete M-200 and curing complete 2.20 Cum 9021.71

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Lintel for Ground floor.

20 Providing and fixing 90 cm high Stainless steel railing made from anti 26.00 Rmt. 3719.83

corrosive 304 grade S.S. pipe of 50 mm dia. (16 gauge) as hand rail with S.S.

304 grade baluster of 38 mm dia. (16 gauge) as a vertical support fixed in

RCC slab at 1.2m c/c including three horizontal S.S. pipes of 25 mm dia. (16

gauge) at equal distance fixed by 18.75 mm dia (16 gauge) S.S. pipe with

baluster including accessories as per detailed drawing as directed etc.

21 Providing I.S.I. Mark T.M.T. bar Fe-500D reinforcement with fusion bonded 85882.50 Kg. 77.29

epoxy coating not less than 175 micron thickness and upto 300 micron to

reinforcement bars as per IS-13620-1993/ASTM-775M (including testing of

coating at plant and all taxes) for R.C.C. work including bending, binding and

placing in position complete upto floor two level for Ground floor.

22 Providing I.S.I. Mark T.M.T. bar Fe-500D reinforcement with fusion bonded 4761.00 Kg. 78.34

epoxy coating not less than 175 micron thickness and upto 300 micron to

reinforcement bars as per IS-13620-1993/ASTM-775M (including testing of

coating at plant and all taxes) for R.C.C. work including bending, binding and

placing in position complete upto floor two level for First floor level.

23 Providing and laying brick work using common burnt clay building 141.50 Cum 4214.33

conventional type bricks having crushing strength not less than

Kg./Sq.cm. in foundation and plinth in cement mortar 1:6 (1 cement : 6 fine

sand) including the cost of all materials and labour charges etc. complete.

24 Providing and laying brick work using common burnt clay building 631.20 Cum 4496.05

conventional type bricks having crushing strength not less than 35 Kg/sq.cm.

in super structure above plinth level upto floor two level in cement mortar 1:6

(1 cement : 6 fine sand) for Ground Floor including the cost of all materials

and labour charges etc. complete.

25 Providing and laying brick work using common burnt clay building 18.80 Cum 4538.16

conventional type bricks having crushing strength not less than 35 Kg/sq.cm.

in super structure above plinth level upto floor two level in cement mortar 1:6

(1 cement : 6 fine sand) for First Floor including the cost of all materials and

labour charges etc. complete.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

26 Providing and fixing 150 mm wide, approved quality chicken wire mesh at 5590.40 Sq.m. 301.12

junction of brick work and RCC work or two dissimilar surfaces, at all heights

fixed by nails, rowal plugs or tag by cement mortar 1:3 before applying the

plaster, including curing etc. complete

27 Providing 15mm thick cement plaster in single coat on rough (similar) side of 615.50 Sq.m. 226.01

single or half brick walls / concrete wall for interior plastering and finished

even and smooth along with floating coat of neat cement slurry etc. complete

in Cement mortar 1:4 (1-cement : 4 sand) at Ground floor.

28 Providing 15mm thick cement plaster in single coat on rough (similar) side of 96.10 Sq.m. 249.90

single or half brick walls / concrete wall for interior plastering and finished

even and smooth along with floating coat of neat cement slurry etc. complete

in Cement mortar 1:4 (1-cement : 4 sand) at First floor.

29 Providing 20mm thick double coat sand faced cement gutka plaster on walls 758.40 Sq.m. 345.75

with 1 x 1 cm grooves consisting of 12 mm thick backing coat of C.M. 1:3 (1

cement : 3 sand) and 8 mm thick finishing coat of C.M. 1:1 (1 cement :

sand) including 1 cm x 1 cm grooves etc. complete as directed by Engineer-

in-charge.

30 Providing throating or plaster drip and moulding to R.C.C. Chhajja. 61.80 Rmt. 43.05

31 Applying two coats of acrylic lappy - putty & two coats of primer of approved 711.60 Sq.m. 40.59

brand and manufacture on new wall surface to give an even shade including

thoroughly brushing the surface free from mortar dropping and other foreign

matter and sand papered smooth for all floors.

32 Wall painting (two coats) with plastic emulsion paint of approved brand and 711.60 Sq.m. 82.85

manufacture on undecorated wall surfaces to give an even shade including

thoroughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth for all floors.

33 Finishing wall with weather proof exterior 100% acrylic emulsion paint with 758.40 Sq.m. 120.26

one coat of primer on wall surface to give an required shape even shade

after thoroughly brushing the surface to remove all dirt, dust and remains of

loose powdered materials etc. complete for all floors.

34 Providing and fixing window having two shutter glass section and one shutter 26.40 Sq.m. 2597.98

mosquito net extruded colour anodized aluminum section equivalent to Jindal

series E(30 mm) with sections numbered : frame bottom with weep holes-

20737, frame top & side - 20738; shutter top & bottom- 20993, shutter-inter

lock - 20550, shutter side (handle) - 20549, with 5 mm thick transparent

tinted float glass, with rubber gasket, air lock strip and finishing joints with

transparent silicon sealant, with standard extruded colour anodized aluminum

fittings. Window W1, W2 & W3.

35 Providing Plinth Protection to building including excavation and laying cement 222.30 Sq.m. 2520.98

concrete 1:3:6 using stone aggregates of 40mm nominal size in foundation

layer 150 mm thick+ 125mm thick sand layer below pre-cast rubber dye inter

locking concrete block 60mm thick with grade of concrete M-300 pneumatic

compressed by mechanically pressed and as per approved design including

75mm sand layer for levelling and filling the joint with sand in proper line and

level etc. complete including providing and fixing precast concrete kerb stone

of grey cement based concrete block 30cm length, 30cm height and 15cm

thick made of M-250 grade concrete as per approved design and including

excavation for fixing in proper line and level, filling the joint with C:M 1:3 (1

cement : 3 fine sand) etc. complete.

36 Providing and laying broken china mosaic flooring for terrace using 12 mm to 112.60 Sq.m. 779.70

20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to

plain or slope and to be tempered to bring mortar creme out upto surface

using white cement including rounding off junctions and extending them upto

15 cm along the wall, clearing with water and oxalic acid etc. as directed.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

37 Providing and fixing M.S. Grills of required pattern to frames of windows etc. 26.40 Sq.m. 3095.77

with M. S. flats at required spacings and frame alround having min. weight of

grill 25 kg/sq.m, square or round bars with round headed bolts and nuts or by

screws including priming coat of approved quality and two coats of enamel

paint, as directed by engineer in charge (A) Plain grill.

38 Providing and fixing rolling shutters of approved make made of 80 mm wide 25.00 Sq.m. 3554.40

M.S. laths inter-locked together through their entire length and jointed

together at the end locks mounted on specially designed pipe shaft with

bracket plates, guide channels and arrangements for inside and outside

locking with push-pull operation including the cost of hood cover and spring

etc. complete (A) Shutters having width above 3.5 mt.

39 Steel work, welded in built up sections framed work including cutting, 1348.20 Sq.m. 1068.93

hoisting, fixing in position and applying a priming coat of red lead paint. (D) In

trusses and trussed purlins, upto 25 M. span and 15 M. overall height. (Steel

work 10 Kg./Smt.)

40 Providing and fixing PROFLEX or equivalent self supported Roof (Arch Type) 1348.20 Sq.m. 3597.69

using Cold rolled, Galvalume steel colour coated sheet 1.2mm thick

conforming to ASTMA 653, A792 DIN, ALU Zinc coating : AZ150 and Regular

Modified Polyster painting with epoxy primer service coat at bottom including

necessary fixtures & fastening for lighting arrangement and turbo ventilator

with sky light etc. complete as directed by Engineer in charge.

41 Providing and fixing Turbo Ventilator made from Alluminium and stainless 9.00 No. 9527.73

steel with ploy Carbonate Sky Light of size 2 x 7 feet including fixing in roof

as and where directed by Engineer in charge etc. complete.

42 Box cutting the road surface to proper slop and camber for making a base of 772.50 Cum 109.41

road work including removing the excavated stuff and depositing on the road

side slope as directed for all lead and lift.

43 Providing and laying compacted WBM of Grading-II MCBT metal of size 45 to 273.00 Cum 1851.33

63mm in required layers including using 13% stone screening, 13.2mm size

and 7% stone dust as filler including spreading, watering & consolidation by

vibratory roller etc. complete.

44 Providing and laying cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 260.00 Cum 3092.22

hand broken stone aggregate 40 mm nominal size) and curing complete

excluding cost of form work in foundation and plinth.

45 Providing and laying controlled cement concrete M-200 and curing complete 264.00 Cum 4113.42

including the cost of formwork and excluding reinforcement for reinforced

concrete work in (A) Foundations, footings and Mass concrete.

46 Providing and laying homogeneous grey cement based concrete kerbing of 388.00 Rmt. 374.92

size 30 cm x 30 cm x 10 cm size as per detailed drawing having grade of

concrete M-25 grade, including necessary excavation, BBCC 1:5:10, 7.5 cm

as per detailed drawing fixing in line and level, filling joints in C.M. 1:3 with

smooth finished, white washing three coats etc. complete as directed by

Engineer in charge.

47 Supplying premoulded bituminous joint filler 12 mm thick. 24.00 Sq.m. 553.79

48 Providing, laying (to level or slopes) and jointing reinforced concrete light 30.00 Rmt. 659.99

duty non-pressure pipes I.S. class NP3 of the following internal diameter with

collars and butt ends prepared for collar joints including testing of joints

complete. (i) 300mm

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

Electrical Items

49 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm 20.00 Pt 485.81

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length , in below type of pipe erected with

6A Modular type switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic / Wooden box, single mounting

base frame covered with textured / metallic / white front plate modules

erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder

/ ceiling rose / H.D. Connector as directed. (f) with medium class Rigid PVC

pipe and accessories erected concealed in wall/ceiling complete Cat. III

50 Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin 16.00 Pt 257.55

socket erected on PVC / Metallic / Wooden box, single mounting base frame

covered with textured / metallic / white front plate modules erected on / in wall

/ ceiling with following type accessories. Cat. III

51 Providing following type of Modular Type Accessories mounted with PVC / 12.00 Ea 25.25

metallic / Wooden box, single mounting base frame covered with textured /

metallic / white front plate, modules erected with necessary connections as

per site situation directed by Engineer in charge. (7) Blank Plate Single Cat. III

(9) 16 Amp. SP one way switch Cat. III 8.00 Ea 180.79

(10) 6/16Amp. Universal socket Cat. III 8.00 Ea 199.98

52 Providing and erecting ISI mark Medium class RIGID PVC PIPES of following 9.00 Mtr. 54.54

size complete to be erected on/in wall or ceiling erected with necessary PVC

fittings & Junction boxes fixed with adhesive solution & clamps with following

dia of pipes, in approved manner as directed (c) 32 mm

53 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 988.00 Mtr. 82.82

marked stranded Copper conductor wire in following type of pipe to be

erected concealed in / flushed on wall / ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth

continuity of following size (A) With medium class Rigid PVC pipe and

accessories (b) 2 wire 2.5 sq. mm

54 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 128.00 Mtr. 112.11

marked stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of following size

(A) with medium class Rigid PVC pipe and accessories (a) 2 wire 4 sq.mm

(h) 4 wire 6 sq. mm 170.00 Mtr. 260.58

55 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi 4.00 Mtr. 37.37

stranded, annealed copper conductor with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in existing pipe of following size

(Specifically for control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and bolts if required. (d)

One wire 4.00 sq.mm

(e) One wire 6.00 sq. mm 27.00 Mtr. 56.56

(f) One wire 10.00 sq. mm 4.00 Mtr. 91.91

(h) One wire 25.00 sq. mm 4.00 Mtr. 236.34

(i) One wire 35.00 sq. mm 1.00 Mtr. 300.98

56 Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv 101.00 Mtr. 46.46

grade ISI marked copper wires of following size to be erected as directed. (e)

1.50 Sq.mm 3 core round PVC sheathed

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

57 Providing & erecting Switch board for Computer or electric apparatus 8.00 Ea 1133.22

consisting of following modular type accessories mounted with PVC / Metallic

concealed/open box with single mounting base frame covered with textured /

metallic /white front plate,modules erected with necessary connections as

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories Cat. III

58 Bakelite adopter for Holder to be erected. 12.00 Ea 9.09

59 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 12.00 Ea 535.30

0.5 Watt assembled on single MCPCB, with housing used as a heat sink

shall be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium

die cast powder coated and high U.V. & corrosion resistance with diffuser

with company mark/name 160V to 270V, Power Factor more than 0.95, THD

< 15%, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt, LED LED

driver efficiency > 85% (fitting required LM-79 & LM-80 Certificates) (NOTE:

Below description have shown ranges of Wattage capacity of LED

ranges shown) (A) Tube Light with integral driver (v) 36-40 Watts, Surge-2

KV, IP-20, conventional 4 feet Cat-lll

60 Supplying and erecting LED street light / Flood light fittings with High power 8.00 Ea 5976.17

White LEDs wattage of 3 Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10%, CCT 3000 K to 5700K, Uniformity ratio

>0.45, Luminaire efficacy> 100 lumens/watt. LED driver efficiency > 85%.

(fittings required LM-79 & LM-80 certificates) (NOTE: Below description have

shown ranges of Wattage capacity of LED fittings. The Engineer incharge

(IP-65), Surge protection -4KV integral and Light must have 440VAC line

supply with over-voltage protection. (iii) Above 60 to 90 watts Cat-lll

(B) Flood Light (IP-65), Surge protection -4KV integral and Light must have 34.00 Ea 5599.44

440VAC line supply with over-voltage protection. (ii) above 48 to 60 Watts

(iii) Above 60 to 90 watts Cat III 19.00 Ea 6088.28

61 Providing and erecting Approved make Four pole moulded case circuit 3.00 Ea 6173.12

breaker having breaking capacity ICU of 25 KA. at 415 V, having normal

current rating up to 25 A to 100A. with fixed thermal & magnetic release

suitable to work on A.C. supply 50 c/s. with all internal connections, spreader

tinned copper & complete erected in existing 16 G.M.S. housing. ICS=100%

of ICU only. Cat III

62 Providing and erecting Approved make Four pole moulded case circuit 1.00 Ea 8055.76

breaker having breaking capacity ICU of 35 KA. at 415 V. having normal

current rating 125A. with Fixed thermal & magnetic release suitable to work

on A.C.supply 50 c/s. with all internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only. Cat

63 Providing and erecting Approved make Earth fault Relay suitable to mount 1.00 Ea 4687.41

with inter connection suitable to following size of moulded case circuit

breaker having CT ratio & MCCB rating as following along with shunt trip

220V AC. with all internal connections & complete erected in existing

M.S.housing. (1) 15 A -100 A, CT Ratio 1/100

(2) 125 A -200 A, CT Ratio 1/200 1.00 Ea 4983.34

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

64 Supplying and erecting triple pole & neutral 440V / 500V panel mounting 0.90 Rn. 1961.42

Copper Busbars with four equal Nos. of electrolyte bus having current density Mtr.

not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of following current

carrying capacity, erected with necessary bus bar supports /insulators, main

cable socket to each bar, erected in existing cubical panel with necessary

connections. (A) Suitable for 100 Amp. Capacity

65 Providing and erecting Miniature circuit breaker single pole 0.5A to 2A 61.00 Ea. 270.68

system and having breaking capacity 10 KA to be erected in existing box.

confirming to IS 8828/1996 with ISI Mark Cat III

66 Providing and erecting Miniature circuit breaker single pole 6A to 25A 64.00 Ea. 112.11

suitable to operate on 240 V A.C. system and having breaking capacity

KA to be erected in existing box confirming to IS 8828/1996 with ISI Mark Cat

67 Providing & erecting 240 V MCB double pole switch for motor & inductive 5.00 Ea. 330.27

load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in

existing box having following capacity (B) 40 Amp. Cat III

68 Providing & erecting 240 V MCB double pole switch for lighting Load (B 3.00 Ea. 278.76

Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box

having following capacity (A) 6 to 32 Amp.Cat III

69 Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve) 4.00 Ea. 578.73

having 10KA breaking capacity & confirms to IS :8828 in existing box having

following capacity (A) 6 to 32 Amp.Cat III

(B) 40 Amp. Cat III 12.00 Ea. 638.32

70 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C 2.00 Ea. 668.62

Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box

having following capacity (b) 40 Amp. Cat III

(c) 63 Amp..Cat III 2.00 Ea. 737.30

71 Sheets steel powder coated enclosure suitable for incorporating One/Two 1.00 Ea. 176.75

72 Providing and erecting Sheet Steel powder coated MCB distribution board - 2.00 Ea. 2339.16

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of same company of

MCB to be used) suitable for (B) three phase incoming and single phase

horizontal type outgoing Per phase isolation type (PPI) (b) sheet steel

double door (i) 4 way

(ii) 6 way 2.00 Ea. 2913.85

73 Providing and erecting Approved make RCCBs conforming to IS: 12640 and 12.00 Ea. 2235.13

having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz. having characteristic of

quick action & tripping with all advance feature & do not incorporate any

electronic component for following Max. rating erected as directed (ii)

Amps. DP Cat III

74 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 2.00 Kg. 794.87

75 Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. 6.00 Ea. 368.65

dia. galvanised iron pipe with coupling and buch buried in specially prepared

earth pit complete with necessary 8 SWG earth wire.

76 For using salt and charcoal / coke as required for pipe type earthing. 6.00 Ea. 171.70

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

77 Supplying & erecting earth pit of minimum bore dia.150mm size approved 2.00 Ea. 4591.46

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of

50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-

250 Micron galvanising, connection terminal dia of 12mm with constant

ohmic value surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber and heavy

duty cover. (A) (approved make OEM has to submit test certificate including

value of earth resistance of installation duly stamped and signed by agency

and officer Incharge has to ensure the value of earthing resistane mentioned

in test Certificate) & having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop :- < 1 volt at no load & dry form, Sulphar content :- <2% (C)

Back fill Compound :- Earthing compound should be capable to retain

moisture for long time necessary test report must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

78 Providing & erecting weather proof, dust & vermin proof, floor mounted front 1.80 Sq. 16323.62

operated outdoor type double door cubical panel board necessary IP-54 and Mtr.

above protection as per approval from engineer incharge made from

SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC

M.S.sheet for internal partitions with necessary accesories , supporting

angles/ flats channel including cutting, bending, drilling, welding, riveting with

internal partitions & cable alley as per requirements & instruction of engineer-

in-charge with erection of supplied switch gears, BUSBARS, suitable size of

inter connecting PVC copper wire / copper-aluminium strips, rubber

grommets, rib, bakelite control fuses/MCB for measuring instruments, earth

bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of

hinged doors, handles with locking arrangement and rubber gasket, heavy

duty end terminal connection, danger notice board, necessary ventilation,

earthing strip complete. The Panel shall be painted with epoxy powder

(The rates excludes the cost of switchgears, bus bars, inter connecting mains

& Copper Aluminium strips, meters, Fuses etc. The dimension shall be

measured excluding base beams) The panel shall be supplied with following

approved manufacturers with following size. (B) The standard companies

switch gear shall be used and only manufacturers at CPRI approved factory

(i) with 350mm depth

79 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand 125.00 Mtr 220.18

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or

in existing trench / pipe of following size of cables (B) 3 1/2 core 35 Sq.mm

(16 Sq. mm 1/2 core)

(C) 3 1/2 core 50 Sq.mm (25 Sq.1/2 mm core) 44.00 Mtr 284.82

80 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / 322.00 Mtr 126.25

Solid Aluminium conductor for 1.1 KV. to be laid on wall with necessary

clamps or in existing trench / pipe of following size of cables (B) 4 core

81 Making trench in soft soil of suitable width of 90 cm deep for laying cable or 265.00 Mtr 55.55

locating the fault all over the run and back filling the same and making the

surface as normal ground.

82 Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm. below 11.00 Mtr 226.24

ground across the road crossing or on floor with necessary material in an

approved manner and making the ground as per original. (F) 100 mm dia.

83 Providing & laying approved make Double walled corrugated pipes (DWC) of 306.00 Mtr 62.62

polyethylene (conforming to IS 14930 II) with necessary connecting

accessories of same material at required depth in existing trench for laying

of cable below ground / road surface for enclosing cable (A) 50 mm outer dia.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

84 Providing and, fixing heavy duty flange type brass cable gland with rubber 50.00 Ea 38.38

ring for PVC insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables.(B) 2 to 4 core 6 Sq. mm

85 Providing and, fixing heavy duty flange type brass double compression type 4.00 Ea 75.75

cable gland with rubber ring for PVC insulated armoured cable complete with

out going tails, insulating tape etc for following size of cables.(B) 3 & 1/2

core 35/50 Sq. mm

86 Solder less crimping type Aluminium lugs conforming to IS suitable for cable 200.00 Ea 6.06

of following size evenly crimped with high pressure tool & connected to

switchgear terminals with brass / cadmium plated nut bolts in an approved

manner. (A) 1.5/ 2.5/4/6 Sq.mm

87 Supplying and erecting approved make oscillating type bracket fan A.C. 8.00 Ea 2534.09

23OV. 50cy/s 400/450 mm sweep wall mounted with height adjustment and

rotary tilting device complete with guard, flexible Core plug top complete

erected with lead wires as directed.Cat.II

88 Supplying and erecting approved make Octagonal pole made from HR sheet 6.00 Ea 6874.06

steel. The pole should be made as per IS. and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable suspend local wind speed

with integral Junction box consist of terminal plate of min 6mm Hylam sheet,

standard profile 35mm x 7.5mm Din-Rail for MCB Mounting, stud type

terminal and arrangement for cable termination to be erected With Suitable

foundation (Included) as per details given by manufacturer considering site

requirement. (C) 5 Mtr. Long 70 mm top x 130 mm bottom dia, 3 mm

thickness with 200mm x 200mm x 12mm base plate, 4-M16 bolts and 600mm

long with necessary G.I. J bolts. Approx Pole weight 46 kg

89 Supplying & erecting approved make SMC press moulded composite FRP 2.00 Ea 898.90

loop-in, loop-out approx. 2mm thick box complete with Bakelite connector

strip 5way (3P+N+E), DIN rail for mounting mob & hinged doors as per

requirement having locking arrangements with mounting clamp with nuts,

bolts & washers suitable for erection on pole with cable clamps& earth bolt of

following size of box. (A) 300mm x 200mm x 100mm [deep]

(C) 150mm x 125mm x 100mm [deep] 53.00 Ea 476.72

90 Supplying and erecting Street light pole bracket comprising main B Class GI 4.00 Ea 491.87

pipe of 4.2 cm/require outside dia. complete with suitable B Class G.I. sleeve

tubing of approx. 45cms. length and suitable for 76.5mm / 80mm / require

size of pole top having nuts and bolts for fixing the brackets and having

spread of 0.5 mtr. Length with 110 deg.with vertical plane and suitable

welded stiffener reducer and nipple with check nut complete painted with one

coat.of Red oxide / PU base primer and two coats of Aluminium / PU paint.

paint with following nos of arms. [A] Single Arm bracket 0.5 Mtr

[B] Double Arm Bracket 0.5 Mtr 2.00 Ea 622.16

91 Supplying & erecting approved make Digital time switch having lithium cell 6 2.00 Ea 3168.37

years operative and operate battery backup 1 channel day clock with

memory programme, suitable to operate on 240V + 5%, 16A with, floating

contacts Minimum switching setup time 1 minimum & LCD display. Also

comprised permanent ON/OFF switching. Programming switches & housed

in fire proof thermoplastic enclosure & transparent cover erected as required

with necessary connection erected as directed.

92 Supplying & erecting power contactor ,AC3 duty for time switch complete 2.00 Ea 857.49

erected as per direction Cat III (C) 4 pole 440V 16 Amp.

93 Supplying and erecting approved make panel mounting type Digital Voltmeter 2.00 Ea 1275.63

having 3 digits LED display, 0 to 750 AC Volts range erected on existing

panel board with all connection, wiring etc. with manufacturers calibration

certificate.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

94 Supplying and erecting approved make panel mounting type Digital Ammeter 2.00 Ea 1558.43

having 3 digits LED display, external CT operated, calibrated for 0 to

Amps suitable to operate on 500 Volt AC, erected on existing panel board

with all connection, wiring etc. with manufacturers calibration certificate.

Supply 500 V on existing panel board with necessary connections.

96 Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 6.00 Ea 274.72

ratio 15 VA burden erected in existing CRCA box duly secured with insulating

materials connected to the meter

97 Supplying and erecting approved make suitable panel indicator LED type 6.00 Ea 43.43

lamp, lens cover, complete erected with necessary connections.

98 Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible 88.00 Mtr. 104.03

Submersible copper cable approved make of following size. (B) 3 Core x

99 Supply, Installation, Testing & Commissioning of following size of Grid Tied

Solar Power Plant with Solar Panels (ALMM approved): Frame Material :

Anodized Aluminum alloy Frame With Twin Wall Profile, Front Cover : High

Transmission Low-Iron Tempered Glass (AR Coated), High efficency and

positive power tolerance Pmax: 0/+5, Module efficiency should be approx.

19.5%-22%, Normal operating temperature 45'C, Junction Box with

Waterproof IP67 & MC4 Compatible and Enclosed with Bypass diodes, 100%

Electroluminescence test to ensure error free Modules, Thep. temp. co-

efficient of the PV module shall equal or better than -0.45% / degree C. Solar

PV modules of minimum fill factor 75% to be used. Unit Production:- More

than 4.5 Unit /kw /day (Actual)(1Year Avg) With 10 year Product warranty

and 25 year Linear Power Warranty includes all mechanical and electrical

parameters of the Solar panel. Modules must be complied to the

DCR(Domestic content requirements). The Ration of AC to DC is 5:6 for the

Installation capacity which are given in AC KW.

Solar Inverter: MPPT Range: MPPT Range: 80-1000 V , Max efficiency:

97.5% - 98.9%, O/p Frequency: 50/60Hz, Operating Altitude (m) ≤4000, O/p

Power Factor: ~1, O/P THDi: <3%, Operating Tempreture Range: -25~60°C,

Integrated protection of Inverter are Anti-islanding Protection, Input Reverse

Polarity Protection, Insulation Resistor Detection, Ground fault protection,

Residual Current Monitoring Unit, Output Over Current Protection, Output

Short Circuit Protection, Output Over Voltage Protection, PV array string fault

Protection. Protection Degree: IP65, User Interface LCD & APP, Datalogger

& Communication: GPRS / Wi-Fi.

Communication: GPRS / Wi-Fi, Module Mounting Structure: The mounting

(Rectangular pipe / square pipe / circular pipe) with requisite cross bars, nuts

and bolts, etc. shall be Hot deep galvanized with minimum 80micron coating.

The Rectangular / square /circular hollow pipe section used for the structure

should have a minimum thickness of 2.0 mm. other than above, the material

thickness should be minimum 2.5 mm. A certificate of a structural engineer

certifying the strength and stability of the mounting structure to withstand the

weight and wind speed of 150 km/hour throughout the life span of 25 years of

the system, shall be submitted by the vendors. Hot Dipped Galvanized steel

coils. suitable arrangement for base plate for foundation , solar panel

mounting, the structure should be suitable for carry the load of solar

panel,wiring, sprinkler system etc. with necessary foundation work/wall

mount, j bolt, anchor fastner etc. the nut bolt used for installtion of stucture

should be (SS 304) quality.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

The ground clearance of the bottom most edge of solar panel shall not be 7.00 Per 44081.45

less than 300 mm to 1200 mm or as per site’s technical / feasibility KW

requirement.

a. Column –The minimum section (thickness) should be 60MM x 40MM

b. Rafter - The minimum section (thickness) should be 60MM x 40MM

c. Purlin - The minimum section (thickness) should be 40MM x 40MM Balane

of System with necessary Swichgears (Suitable size and protection of ACDB

& DCDB), inter connecting wiring, earthing system as per the CEIG drawing

approval, lightining arrester system as per the CEIG drawing approval, all

liasoning work with various Govt. Department like state nodal agency,

DISCOM & CEIG is included in agency scope

(Excluding All charges namely GEDA Application fees, Solar connectivity

Charges, Meter connectivity Charges, Meter testing Charges and system

stability/strenthning charges) (B) Grid Tied Solar Power System: 7 - 10 kW (3

- phase) (B) Grid Tied Solar Power System : 7 - 10 kW (3 - phase)

100 SITC of 3 phase Air cooled 15 KVA Indoor unit Servo voltage stabilizer of 1.00 Ea. 58327.50

input voltage range of 340V-480V and nominal output voltage of 415V with +-

1% Voltage Regulation with necessary cable termination on input and output

side and 1 year Warranty as per as Per attached technical specification.

Total Rs.

i.e. Rs. Two Crore Ninety Eight lacs Fifty One thousand Eight hundred Fifty Two and Eighty One paisa only.

I/We am/are willing to carry out the work @ ______________ % above/below percent (Should be written

in figures and words) of the estimated rate mentioned above. Amount of my /our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

Net Rs. ___________________________ Total Rs. ________________________

In words ____________________ In words ____________________

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-

Charge for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is

a change as per actual mix design the cost of difference of cement consumption have been deducted from the rate

of original item at the rate of input rate mentioned in all the tender.

5. The Contractor will have to submit the all required mix design at his own cost before execution as directed

and to be approved from the Engineer in charge.

Above all items of "Schedule-B" with Item Description, Unit, Rate & Amount have verified by me and found

Deputy Executive Engineer Sr. Divisional Account Officer Executive Engineer

Lunawada (R & B) Sub Division, Mahisagar (R & B) Division, Mahisagar (R & B) Division,

Lunawada Lunawada Lunawada