Tenderization for ARC Work of Laying testing & commissioning of 11/22 KV UG XLPE CABLE with 11/22 KV Cable End Termination & ST joint Kits (to be Supplies by Agency) along with Erection of HT,LT & TC , Maintenance works under CFC and if required any other Sdn under jurisdiction of Sachin Division under ND and if Required Any other Scheme.

The statement showing items of works to be carried out for erection work of HT/LT lines , T/C ,Laying Testing &

Commissioning of XLPE UG CABLE & maintenance of feeders for various scheme for Various sub division under

the control of Sachin (O&M) Division.

HT,LT &TC Revised as per Letter No DGCS/1408/01/2025 Approved Date: 27-01-2025

Ammendment HT,LT &TC Revised as per Letter No DGCS/0693/02/2025 Approved Date: 12-02-2025

Maintenance Revised as per Letter No DGCS/1410/01/2025 Approved Date: 27-01-2025

UG Cable Revised as per Letter No DGCS/1411/01/2025 Approved Date: 27-01-2025

Name of Work :- Rate contract for erection of HT/LT line & T/C , UG work for various scheme work for SDN office

under Sachin Division Office. ( For Works Up to 200 MTR UG + OH Works)

ITEM CODE Details of Works Qty Unit Amount

Labour charge for excavation of cable trench of 400mm

width x 1200mm depth, in any type of soil for laying of cable

1 9925000001 of size up to 240 mm2 (For additional cable 200 mm Meter 72

additional width shall be considered i.e. half trench length is

to be considered)

Labour charge for excavation of cable trench of 600mm

width x 1200mm depth, in any type of soil for laying of cable

2 9925000002 of size up to 240 mm2 (For additional cable 200 mm Meter 109

additional width shall be considered i.e. half trench length is

to be considered)

Labour charge for excavation of cable trench of 400mm

width x 1500mm depth, in any type of soil for laying of cable

3 9925000003 of size up to 240 mm2 (For additional cable 200 mm Meter 91

additional width shall be considered i.e. half trench length is

to be considered)

Labour charge for laying of 11kV / 22 kV XLPE Cable of

size up to 240 mm2 & preparation of sand layer 100mm

thick, in the cable trench & covering the cable with 150 mm

dia (Inner), thickness 25 mm, 1.0 meter long RCC half

round muffs and providing and fixing of 4inch width yellow

4 9925000004 colour polyethylene tape with printing "CAUTION Meter 171

ELECTRIC CABLE BELOW" at 0.75 m depth from ground

surface after laying cable in trench. This will provide

indication that electric cable is passing underground so as

to protect cable from mechnical injuries, refilling the same,

as per Instruction of Engineer in Charge (EIC).

Labour charge for horizontal drilling using Auger machine

without damage to surface road at max 2.0 mtrs depth &

putting of 6.11 kg/cm2 , class-4,Green color, 110mm O.D.

8.5mm thickness H.D.P.E. pipe confirms to IS 4984-

1987(3rd revision) and BIS certification and laying of

11KV/22KV XLPE cable of size up to 240 mm2 in HDPE

5 9925000005 pipe, as per Site Condition (excluding cost of pipe). The Meter 860

detail map obtained from HDD machine and excell

sheet(hard and soft copy) indicating the respective depth

and distance from adjacent landmark for each segment for

HDD is must required to be submitted. HDD to be carried

out at depth 1.5 mtrs to 2.0 mtrs as per site conditions and

as per instruction of EIC.

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

Labour charge for horizontal drilling manually without

damage to surface road at max 2.0 mtrs depth & putting of

6.11 kg/cm2 , class-4,Green color, 110mm O.D. , 8.5mm

thickness H.D.P.E. pipe confirms to IS 4984-1987(3rd

revision) and BIS certification and laying of 11KV/22KV

XLPE cable of size up to 240 mm2 size, as per Site

Condition (excluding cost of pipe). The detail map and

excell sheet(hard and soft copy) indicating the respective

depth and distance from adjacent landmark for each

segment of cable to be submitted. Drilling to be carried out

at depth Minimum 1.2 mtrs to 2.0 mtrs as per site conditions

as per instruction of EIC.

Supply of 6.11kg/cm2 , class-4,Green color, 110mm O.D.

8.5 mm thickness H.D.P.E. pipe confirms to IS 4984 and

BIS certification for laying of underground 11KV / 22KV

XLPE cable up to 240 mm2 size.

Labour work for RCC concreting on disputed location and

repairing of damage portion of road crossing for the work

carried out for roads crossing as well as concreting &

muffing of ploes including all materials (1:2:4)

Providing & fixing concrete stone route marker of 300 mm

width x 150 mm thick x 650 mm height embedded in earth at

least 300 mm below & 350 mm above ground level

respectively at distance approx 50 meters along the length

of cable. The RCC concreting (1:2:4)(all necessary

maeterials will be in bidder's scope) of route marker is to be

carried out 300 mm width x 150 mm thick x 300 mm below

9 9925000009 ground level as per instruction of EIC. The route marker No. 446

should be with name of company with approved yellow

colour-DGVCL. The distance from marker to cable and

cable depth with feeder name etc., marked with arrow sign

is to be painted on it.The route marker is to be fixed at

location near to any fixed permanent location (not

necessary to fix exact on top of cable) as per instruction of

Erection of D.P. (double pole) structure using 9 / 11 Mtr.

RSJ pole with cable connection arrangement along with

10 9925000010 fitting of necessary fabrication for 11KV cable including No. 2026

excavation of pit & refilling of earth as per instruction of EIC.

(Exclusive of concreting & muffing of poles)

Erection of Single pole structure using 9 / 11 Mtr RSJ pole

with cable connection arrangement along with fitting

11 9925000011 ofnecessary fabrication for 11KV/22 KV cable including No. 1047

excavation of pit & refilling of earth as per instruction of EIC.

(Exclusive of concreting & muffing of poles)

Erection of D.P. (double pole) structure using 8.0 Mtr. PSC

pole with cable connection arrangement along with fitting of

12 9925000012 necessary fabrication for 11KV cable including excavation No. 1416

of pit & refilling of earth as per instruction of EIC. (Exclusive

of concreting & muffing of poles)

Erection of Single pole structure using 8.0 Mtr PSC pole

with cable connection arrangement along with fitting

13 9925000013 ofnecessary fabrication for 11KV/22 KV cable including No. 613

excavation of pit & refilling of earth as per instruction of EIC.

(Exclusive of concreting & muffing of poles)

Labour charge for erecting of 11kV / 22 kV XLPE cable of

size up to 240 mm2 on DP Structure with fixing of 02 Nos

polymer cleats on top and middle part.Polymer cleats, nut

bolts etc. fixing material to be provided by contractor.

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

Providing & fixing of 6.11kg/cm2 , class-4,Green color,

110mm O.D. , 8.5mm thickness H.D.P.E. pipe confirms to

IS 4984 and BIS certification on the erected DP structure for

the mechanical protection of cable by inserting the cable

15 9925000015 inside HDPE pipe. The HDPE pipe shall be erected in such Per Job 1461

a way that 300mm shall be below the ground level and the

rest 2700 mm shall be supported on the DP Structure with

01 No Polymer cleat.All materials including polymer cleat

and Nut bolt to be provided by contractor.

Providing and fixing of pipe type earthing from 80 mm dia

class-B GI pipe with pit to be filled with salt & coke and

construction of chamber as per DGVCL Drg. No. dg /100 for

DP and cable. The earthing pit should be joined with cable

by G.I. strip of size 1” width & 2 mm thick. All material GI

pipe, Coke, Salt etc will be supplied by bidder.

Supply & fixing of heat shrink type end terminations

17 9925000017 (outdoor) for upto 11kV 3C x 185 mm2 size XLPE cable No. 3635

as per DGVCL technical specification

Supply & fixing of heat & shrinkable end terminations

18 9925000018 (outdoor) for upto 22 kV 3C x 185 mm2 size XLPE cable as No. 6231

per DGVCL technical specification)

Supply & fixing of heat shrink type end terminations (indoor)

19 9925000019 for upto 11kV 3C x 185 mm2 size XLPE cable as per No. 3635

DGVCL technical specification)

Supply & fixing of heat & shrinkable end terminations

20 9925000020 (indoor) for upto 22 kV 3C x 185 mm2 size XLPE cable as No. 6231

per DGVCL technical specification

Supply & fixing of heat shrinkable straight through joint for

21 9925000021 upto 11kV 3C x 185 mm2 size XLPE cableas per DGVCL No. 6774

technical specification.

Supply & fixing of heat shrinkable straight through joint type

22 9925000022 for upto 22kV 3C x 185 mm2 size XLPE cable as per No. 11590

DGVCL technical specification

Labour charge for excavation of 2100mm long x 1200mm

wide x 1200 mm deep joint pits for installation of 11kV /

22kV Straight through joints as per instruction of engineer-

in-charge & covering the cable with 150 mm dia (Outer),

thickness 25 mm, 1.0 meter long RCC half round muffs &

refilling same as per instruction of EIC .

Providing and fixing of insulating bus bar, made from

11KV/22KV XLPE cable after removal of semi conducting

layer and applying of PVC heat shrinkable anti-tracking core

insulating tubing (1.1KV), on both end terminal using

Aluminium long barrel heavy duty up to 240 sq mm lugs,

24 9925000024 Aluminium bus connector. Taping with PG- clamp for bus No. 1661

conductor as per drawing and as per instruction of EIC. The

Alluminium lugs and PG clamp shall be covered with

11KV/22KV HT insulating tapes.(11KV/22KV XLPE cable

will be in scope of DGVCL while all other materials will be in

bidder's scope)

Testing of cable at various points and commissioning

25 9925000025 the feeder as per instruction of engineer-in-charge.Test No. 2125

result shall be submitted by contractor with bill.

Preparation and submission of 6 (six) copies, of complete

layout drawings with GIS mapping as per actual cable

routing showing road crossing, HDPE pipe sleeving, jointing

locations, markers etc.

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

Providing and fixing of Sign Board at junction point Made

out of 2 mm aluminium sheet size 750x300 mm (2.5 x 1ft)

rectangle, as per design, pre treated with phosphate

process and acid etching coated with one coat of epoxy

primer and two coats of best quality paints, refloctrorised

with Hi-Intensity retro – reflective sheeting as per the latest

and frame fabricated from suitable size iron angle. The Sign

27 9925000027 Board is to be fixed on the base prepared from channel and No. 10023

bracing angles which is grouted by means of cement

concreting of 1:2:4 for size of 300 mm dia x 800 mm height

(500 mm to be grouted in ground). The details to be

displayed on sign board will be given by In-charge

(a) Hi intensity Micro prismatic Grade

Providing and fixing of Sign Board (Danger Board) on

Distribution Transformer Centers

Made out of 2mm aluminium sheet size 300x300mm (1x1ft)

as per design, pre treated with phosphate process and acid

etching coated with one coat of epoxy primer and two coats

28 9925000028 of best quality paints, refloctrorised with Hi-Intensity retro- No. 2805

reflective sheeting as per the latest and frame fabricated

from suitable size iron angle. The Sign Board (Danger

Board is to be fixed at the location as per instruction of In-

charge Engineer.

(a) Hi intensity Micro prismatic Grade

Providing & fixing of aluminium tag of size 250 mm (L) x

mm (W) from 3 mm aluminium sheet along with 1.0 mm dia

aluminium binding wire for fixing of aluminium tag near end

29 9925000029 termination joint at DP structure for identifyng the cable. No. 83

The details of feeder i.e. 11 / 22 KV with feeder name

shound be punched on the tag by letter punch of size

mm as per instruction of In-charge Engineer.

Supply & fixing of heat shrink type end terminations

30 9925000030 (outdoor) for 11kV 3C x 240 mm2 size XLPE cable as per No. 4427

DGVCL technical specification

Supply & fixing of heat & shrinkable end terminations

31 9925000031 (outdoor) for 22 kV 3C x 240 mm2 size XLPE cable as per No. 6231

DGVCL technical specification)

Supply & fixing of heat shrink type end terminations (indoor)

32 9925000032 for 11kV 3C x 240 mm2 size XLPE cable as per DGVCL No. 4338

technical specification)

Supply & fixing of heat & shrinkable end terminations

33 9925000033 (indoor) for 22 kV 3C x 240 mm2 size XLPE cable as per No. 6231

DGVCL technical specification

Supply & fixing of heat shrinkable straight through joint for

34 9925000034 11kV 3C x 240 mm2 size XLPE cableas per DGVCL No. 6829

technical specification.

Supply & fixing of heat shrinkable straight through joint type

35 9925000035 for 22kV 3C x 240 mm2 size XLPE cable as per DGVCL No. 11590

technical specification

Installation, Testing and commissioning of 11 KV,630 A

SCADA Compatible, RRL type- 3 Way RMU including Two

numbers of earthings as per Drawing (material is in bidder's

scope) and as per DGVCL Technical specification.

Installation, Testing and commissioning of 11 KV,630 A

SCADA Compatible, RRLL type- 4 Way RMU including Two

numbers of earthings as per Drawing (material is in bidder's

scope) and as per DGVCL Technical specification.

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

Installation, Testing and commissioning of 22KV,630 A

SCADA Compatible, RRL type-3 Way, RMU including Two

numbers of earthings as per Drawing (material is in bidder's

scope) and as per DGVCL Technical specification.

Installation, Testing and commissioning of 22KV,630 A

SCADA Compatible, RRLL type-4 Way, RMU including Two

numbers of earthings as per Drawing (material is in bidder's

scope) and as per DGVCL Technical specification.

Construction of plinth for 11KV, RRL type- 3 Way (i.e Two

numbers of Isolator & One number of Breaker) Ring Main

40 9925000042 Unit as per DGVCL's technical specification mentioned in No. 28043.22

drawing no: Drg. 11kv-01. All required material will be

supplied by contractor.

Construction of plinth for 11KV, RRLL type- 4 Way (i.e Two

numbers of Isolator & Two number of Breaker)Ring Main

41 9925000043 Unit as per DGVCL's technical specification mentioned in No. 32345.76

drawing no:Drg. 11kv-02.All required material will be

supplied by contractor.

Construction of plinth for 22KV, RRL type- 3 Way (i.e Two

numbers of Isolator & One number of Breaker) Ring Main

42 9925000044 Unit as per DGVCL's technical specification mentioned in No. 32345.76

drawing no: Drg. 22kv-01. All required material will be

supplied by contractor.

Construction of plinth for 22KV, RRLL type- 4 Way (i.e Two

numbers of Isolator & Two number of Breaker)Ring Main

43 9925000045 Unit as per DGVCL's technical specification mentioned in No. 37090.68

drawing no:Drg. 22kv-02.All required material will be

supplied by contractor.

Modifications e.g.Providing and fixing of Terminal protectors

i.e. Re-use able boot (HT Side 11/22KV, LT Side 1.1KV)

including 11/22 KV insulating taps and L.T.(1.1 KV)

insulating taps ,Busbar, Tapping from Bus Bar (11/22 KV

XLPE cable) through P.G. Clamp for H.T. Jumper to D.O.

Fuse to bushings of Transformer Center, providing & Fixing

of jumper and providing & fixing of Heat Shrinkable Anti

Tracking Core Insulating Tubing (Insulation Level 11/22 KV)

in H.T. jumper , Clamping arrangement of cable support

frame on both side of existing Over Head type Distribution

Transformer to utilize in Under Ground cable network as per

drawing & as per instruction of Engineer incharge. All live

parts i.e. PG-Clamp, connections of D.O.fuses, HT

bushings etc . shall be covered with fixinng of 11/22 KV HT

insulating tapes. ( 11/22 KV XLPE cable will be in scope of

DGVCL while all other materials will be in bidder's scope ) .

Laying of any size of 11/ 22 KV XLPE /PILC Cable in per cable per

redaymade trench or in open space mtr

46 9925000060 Labour charges for Lying of O/H XLPE cable pole to pole KM 70320

Supply of 150 mm dia (Inner), thickness 25 mm, 1.0 meter

long RCC half round pipe

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

Laying (Including Installation , Testing and Commissioning)

of various size of 11 KV XLPE Insulated alluminium

armoured cable in ground 1200 mm Deep , 300 mm Wide

Trench, Providing sand cushioning below (75 mm thick layer

of sand ) and above (75 mm thick layer of sand ) of the

cable and covering it with RCC Half round hume pipe (150

1 mm inner dia with thickness of 30 mm,1 meter length) Meter 335

before refilling pre-bonding / warning tap should provide

below 700 mm from the ground level and back filling the

same to make ground level as per original. As per

Specification and drawing og UGVCL. ( RCC Half Round

pipe should be provide thorughout on cable wihtout gap,

only cable will be supplied by DGVCL)

Laying (Including Installation , Testing and Commissioning)

of various size of Double Circuit 11 KV XLPE Insulated

alluminium armoured cable in ground 1200 mm Deep ,

mm Wide Trench, Providing sand cushioning below (75 mm

thick layer of sand ) and above (75 mm thick layer of sand )

of the cable and covering it with RCC Half round hume pipe

2 (150 mm inner dia with thickness of 30 mm,1 meter length) Meter 468

before refilling pre-bonding / warning tap should provide

below 700 mm from the ground level and back filling the

same to make ground level as per original. As per

Specification and drawing og UGVCL. ( RCC Half Round

pipe should be provide thorughout on cable wihtout gap,

only cable will be supplied by DGVCL)

Layingt of HDPE Pipe Confirming to IS 4984:1955

(Ammendment No 2) having diameter 160 mm and

minimum thickness 5 mm at a minimum depth of 1200 mm

below the road surface by push thorugh method by drilling

3 the road with HDD machine/manually without breaking the Meter 825

road surface and laying of any size of HT/LT XLPE

insulated alluminium armoured cable through the duct as

per the instruction of EIC and specifications. (Without cost

of HDPE Pipe , Cable will be supplied by DGVCL)

Supply of HDPE Pipe having 160 mm diameter , minimum

thickness 7.3 mm as per IS (ammendment no 2 - IS

4984:1995) of PE- 100 , 6 kg/cm2 , for laying of 11 KV

Proving and Fixing HT push on/heat shrink type End Indoor

termination kit Preferably 3m(m-seal) or Raychem make at

switchgear end boxes, transformer (PAD/Pole mounted) for

3 core 11 kV XLPE Aluminium Conductor Armoured cable

5 as specified with connection of leads including cutting, No. 5549

stripping of cable, insulations, providing compression type

terminal ,crimping of lugs with suitable crimping tool, indoor

For 300 mm2 HT XLPE Cable

Proving and Fixing HT push on/heat shrink type End

Outdoor termination kit Preferably 3m(m-seal) or Raychem

make at switchgear end boxes, transformer (PAD/Pole

mounted) for 3 core 11 kV XLPE Aluminium Conductor

6 Armoured cable as specified with connection of leads No. 6676

including cutting, stripping of cable, insulations, providing

compression type terminal ,crimping of lugs with suitable

crimping tool, outdoor application.

For 300 mm2 HT XLPE Cable

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

Proving and Fixing HT push on/heat shrink type Straight

Joint Preferably 3m(m-seal) or Raychem make for 3 core

kV XLPE Aluminium Conductor Armoured cable as

7 specified with connection of leads including cutting, No. 8040

stripping of cable, insulations, providing compression type

terminal ,crimping of lugs with suitable crimping tool.

For 300 mm2 HT XLPE Cable

Erection Schedule B-1

HT TAPPING FROM THE EXISTING POLE INCLUDING

FIXING OF CROSS ARMS, CLAMPS ANTI-CLIMBING

DEVICES, DANGER BOARD, INSULATORS ETC.

1 9926000001 COMPLETE AND PAINTING OF FABRICATED No. 481

MATERIALS AND NUMBERING COMPLETE WITH COST

OF PAINTS AS PER STANDARD SPECIFICATION BUT

EXCLUDING ERECTION OF GUY SET AND EARTHING.

ERECTION OF PSC POLES OF 8 *200 KG INCLUDING

EXCAVATION OF PIT AND REFILLING OF EARTH,

FIXING OFCROSS ARMS, TOP FITTING CLAMPS ANTI-

CLIMBING DEVICES, INSULATORS ETC. COMPLETE

AND PAINTING OF FABRICATED MATERIALS USED ON

THE POLES AND NUMBERING WITH COST OF PAINT

AS PER STANDARD SPECIFICATION BUT EXCLUDING

ERECTION OF GUY SET AND EARTHING.

ERECTION OF STEEL POLES OF 9 TO 11 METERS

INCLUDING EXCAVATION OF PIT AND REFILLING OF

EARTH, FIXING OFCROSS ARMS, TOP FITTING

CLAMPS ANTI-CLIMBING DEVICES, DANGER BOARD,

3 9926000003 INSULATORS ETC. COMPLETE AND PAINTING OF No. 1949

STEEL POLE, FABRICATED MATERIALS USED ON THE

POLEAND NUMBERING WITH COST OF PAINT AS PER

STANDARD SPECIFICATION BUT EXCLUDING

ERECTION OF GUY SET AND EARTHING.

ERECTION OF STEEL POLE OF 13 METERS FOR

RAILWAY CROSSING ON BG/MG/NG LINE FOR

0.400/11/22KV OVERHEAD LINES I.E INCLUDING

EXCAVATION OF PIT & REFILLING OF EARTH, FIXING

CROSS ARMS, TOP FITTING CLAMPS,ANTI-CLIMBING

4 9926000004 DEVICES DANGER BOARD, INSULATORS ETC. No. 2325

COMPLETE AND PAINTING OF STEEL POLES,

FABRICATED MATERIALS USED ON THE POLES AND

NUMBERING WITH COSTOF PAINT AS PER STANDARD

SPECIFICATION BUT EXCLUDING ERECTION OF GUY

SETS AND EARTHING.

ERECTION OF DOUBLE POLE STRUCTURE OF

METERS 200 KG PSC POLES INCLUDING EXCAVATION

OF PITS & REFILLING OF EARTHING, FIXING OF

CHANNELS, SUPPORTING ANGLES,CLAMPS, ANTI-

CLIMBING DEVICES DANGER BOARDS,INSULATORS

ETC.COMPLETE AND PAINTING OF FABRICATED

MATERIALS USED ON THE POLES AND NUMBERING

WITH COST OF PAINT AS PER STANDARD

SPECIFICATION BUT EXCLUDING ERECTION OF GUY

SETS AND EARTHING.(WITHOUT AB SWITCH)

ERECTION OF DOUBLE POLE STRUCTURE OF 9 TO

METERS.STEEL POLE INCLUDING EXCAVATION OF

PITS & REFILLING OFEARTH, FIXING OF CHANNELS,

SUPPORTING ANGLES, CLAMPS,ANTI-CLIMBING

DEVICES DANGER BOARDS, INSULATORS

ETC.COMPLETE & PAINTING OF POLES,FABRICATED

MATERIALSUSED ON THE POLES AND NUMBERING

WITH COST OF PAINTSAS PER STANDARD

SPECIFICATION BUT EXCLUDING ERECTION OF GUY

SET AND EARTHING.(WITHOUT AB SWITCH)

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

ERECTION OF DOUBLE POLE STRUCTURE WITH

MOUNTING OF AB SWITCH, HG FUSES OF 8 MTRS

KG PSC POLES INCLUDING EXCAVATION OF PITS AND

REFILLING OF EARTH,FIXING OF CHANNELS

SUPPORTING ANGLES, CLAMPS, ANTI-CLIMBING

7 9926000007 DEVICES, DANGER BOARDS, INSULATORS,DOFUSES No. 3179

ETC. COMPLETE AND PAINTING OF FABRICATED

MATERIALS USED ON THE POLES AND NUMBERING

WITH COSTOF PAINT AS PER STANDARD

SPECIFICATION BUT EXCLUDINGOF ERECTION OF

GUY SET AND EARTHING.(WITH AB SWITCH)

ERECTION OF DOUBLE POLE STRUCTURE WITH

MOUNTING OF AB SWITCH,HG FUSES, 9 TO

METERS STEEL POLES INCLUDING EXCAVATION OF

PITS AND REFILLING OF EARTH, FIXING OFCHANNEL,

SUPPORTING ANGLES, CLAMPS, ANTI-CLIMBING

8 9926000008 DEVICES , DANGER BOARDS, INSULATORS, ETC. No. 4171

COMPLETE AND PAINTING OF POLES FABRICATED

MATERIALS USED ON THE POLES AND NUMBERING

WITH COST OF PAINT AS PER STANDARD

SPECIFICATION BUT EXCLUDING ERECTION OF GUY

SET AND EARTHING.(WITH AB SWITCH)

ERECTION OF DOUBLE POLE STRUCTURES WITH

MOUNTING OFAB SWITCH, HG FUSES,

TRANSFORMERS, LIGHTENING ARRESTORS,

DISTRIBUTION BOX. OF 8 METERS 200 KG PSC POLES

INCLUDING EXCAVATION OF PITS AND REFILLING OF

EARTH, CARTING OF TRANSFORMERS FROMSTORES

TO SITE, FIXING OF CHANNELS, SUPPORTING

ANGLES,BRACINGS CROSS ARMS CLAMPS,

ANTICLIMBING DEVICES DANGER BOARDS,

CONDUCTOR AND CABLE WIRING ETC.COMPLETE

AND PAINTING OF FABRICATED MATERIALS USEDON

THE POLES AND NUMBERING WITH COST OF PAINT

AS PER STANDARD SPECIFICATION BUT EXCLUDING

ERECTION OF GUY SETS AND EARTHING.

ERECTION OF DOUBLE POLE STRUCTURE WITH

MOUNTING OF AB SWITCH,HG FUSES

TRANSFORMERS, LIGHTENING ARRESTORS,

DISTRIBUTION BOX 9 TO 11 METERS STEEL POLES

INCLUDING EXCAVATION OF PITS & REFILLING OF

EARTH CARTING OF TRANSFORMERS FROM STORE

TO SITE, FIXINGOF CHANNELS SUPPORTING ANGLES,

10 9926000010 BRACING, CROSS ARMS,CLAMPS, ANTICLIMBING No. 10609

DEVICES, DANGER BOARDS,CONDUCTOR AND CABLE

WIRING ETC. COMPLETE AND PAINTING OF POLES

FABRICATED MATERIALS USED ON THE POLES AND

NUMBERING AS PER STANDARD SPECIFICATION BUT

EXCLUDING ERECTIONS OF GUY SETS AND

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

ERECTION OF GUY SET INCLUDING EXCAVATION OF

PITS & REFILLING OF EARTH AS PER STANDARD

SPECIFICATION WITH STAY CLAMPS, STAY WIRE,

ANCHOR ROD, TURN BUCKLE, EYEBOLT, GUY

INSULATOR, CEMENT CONCRETE BLOCK ETC. BUT

EXCLUDING CONCRETING.

CONCRETING OF POLES, GUYS, ETC. INCLUDING

12 9926000012 COST OF CEMENT SAND METAL (1:2:4) AND WATER CMT 8396

ETC. AS PER STANDARD SPECIFICATION.

ERECTION OF COIL TYPE EARTHING INCLUDING COST

OF COAL,SALT ETC. BUT WITHOUT COST OF GI WIRE

AS PER STANDARD SPECIFICATION(20kg solt+20kg

ERECTION OF GI PIPE/CI PLATE TYPE EARTHING

INCLUDINGCOST OF COAL SALT ETC. BUT WITHOUT

COST OF PIPE/GIPLATE GI WIRE AS PER STANDARD

SPECIFICATION.(20kg solt+20kg coal)

ERECTION OF STREET LIGHT FIXTURE COMPLETE

WITH CLAMPS, BRASS NIPPLE, BRASS HOLDER TECK

15 9926000015 WOOD BUSH,REFLECTORS FUSE, WIRING ETC. AS No. 359

PER STANDARD SPECIFICATION BUT EXCLUDING

COST OF MATERIALS.

STRINGING OF ALL TYPE OF CONDUCTOR (EXCEPT

DOG CONDUCTOR) FOR 11/22KV & LT LINES ONE COND

INCLUDING FIXING OF INSULATORS, BINDING PER KM

STRINGING OF GI WIRE 8 SWG INCLUDING BINDING

PROVIDING SINGLE PHASE SERVICE CONNECTION

WITH PVC 4MM TWIN CORE CABLE FROM TERMINAL

POLE TO METERING POINT INCLUDING FIXING OF

METER WITH METER EARTHING COMPLETE WORK AS

PER STANDARD SPECIFICATION BUT EXCLUDING

COST OF MATERIALS.

PROVIDING THREE PHASE 4 WIRE SERVICE

CONNECTION WITH PVC 4MM2/10MM2 FOUR CORE

CABLE FROM TERMINAL POLE TO METERING POINT

INCLUDING FIXING OF METER WITH METER EARTHING

COMPLETE WORK AS PER STANDARD SPECIFICATION

BUT EXCLUDING COST OF MATERIALS.

ADDITIONAL COST FOR EXCAVATION OF PIT IN HARD

ROCK AREA FOR ERECTION OF POLE/ GUY ETC. AS

PER STANDARD SPECIFICATION OVER & ABOVE

20 9926000020 NORMAL COST COVERED AGAINST EXCAVATION OF No. 359

PIT UNDER NORMAL SOIL FOR ERECTION OF

POLE,GUY, DOUBLE POLE STRUCTURE EARTHING

WITH THE APPROVAL OF SUPDT.ENGINEER.

PROVIDING GUARDING TO HT LINE ON ROAD/ RAIL

PROVIDING GUARDING OF LT LINES ON ROAD/RAIL

23 9926000023 LT LINE TAPPING- SINGLE PHASE No. 51

24 9926000024 LT LINE TAPPING- THREE PHASE No. 93

LAYING OF OVER HEAD LT CABLE FOR ROAD

25 9926000025 CROSSING,HT LINE CROSSING AND TELEPHONE LINE No. 263

CROSSING ETC.(PER SPAN)

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

ERECTION OF SINGLE POLE STRUCTURES WITH , HG

FUSES,TRANSFORMERS, LIGHTENING ARRESTOR,

DISTRIBUTION BOX. ON 8 METERS 200 KGAND PSC

POLE INCLUDING EXCAVATION OF PITS AND

REFILLING OF EARTH, CARTING OF TRANSFORMERS

FROM STORES TO SITE, FIXING OF CHANNELS,

26 9926000026 SUPPORTING ANGLES,BRACINGS CROSS ARMS No. 4537

CLAMPS, ANTICLIMBING DEVICES DANGER BOARDS,

CONDUCTOR AND CABLE WIRING ETC.COMPLETE

AND PAINTING OF FABRICATED MATERIALS USED ON

THE POLE AND NUMBERING WITH COST OF PAINT AS

PER STANDARD SPECIFICATION BUT EXCLUDING

ERECTION OFGUY SETS AND EARTHING.

ERECTION OF SINGLE POLE STRUCTURES WITH , HG

FUSES,TRANSFORMERS, LIGHTENINGARRESTOR,

DISTRIBUTION BOX. ON 9 to 11 METERS RSJ POLE

INCLUDING EXCAVATION OF PITS AND REFILLING OF

EARTH, CARTING OF TRANSFORMERS FROM STORES

TO SITE, FIXING OF CHANNELS, SUPPORTING

27 9926000027 ANGLES,BRACINGS CROSS ARMS CLAMPS, No. 5305

ANTICLIMBING DEVICES DANGER BOARDS,

CONDUCTOR AND CABLE WIRING ETC.COMPLETE

AND PAINTING OF FABRICATED MATERIALS USED ON

THE POLE AND NUMBERING WITH COST OF PAINT AS

PER STANDARD SPECIFICATION BUT EXCLUDING

ERECTION OFGUY SETS AND EARTHING.

ERECTION OF PSC POLES OF 10 *270 KG INCLUDING

EXCAVATION OF PIT AND REFILLING OF EARTH,

FIXING OF CROSS ARMS, TOP FITTING CLAMPS ANTI-

CLIMBING DEVICES, INSULATORS ETC. COMPLETE

28 9926000028 AND PAINTING OF FABRICATED MATERIALS USED ON No. 2666

THE POLES AND NUMBERING WITH COST OF PAINT

AS PER STANDARD SPECIFICATION BUT EXCLUDING

ERECTION OF GUY SET AND EARTHING.

ERECTION OF DOUBLE POLE STRUCTURE OF

METERS 270 KG PSC POLES INCLUDING EXCAVATION

OF PITS & REFILLING OF EARTHING, FIXING OF

CHANNELS, SUPPORTING ANGLES,CLAMPS, ANTI-

CLIMBING DEVICES DANGER BOARDS,INSULATORS

ETC.COMPLETE AND PAINTING OF FABRICATED

MATERIALS USED ON THE POLES AND NUMBERING

WITH COST OF PAINT AS PER STANDARD

SPECIFICATION BUT EXCLUDING ERECTION OF GUY

SETS AND EARTHING.(WITHOUT AB SWITCH)

STRINGING OF 100MM2 ACSR/100MM2 AAAC

30 9926000030 CONDUCTOR FOR LT LINES INCLUDING FIXING 4861

OFINSULATORS, BINDING JUMPERING ETC.

STRINGING OF DOG CONDUCTOR FOR 11/22KV HT

31 9926000031 LINES INCLUDING FIXING OF INSULATORS, BINDING 4378

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

ERECTION OF DOUBLE POLE STRUCTURES WITH

MOUNTING OF AB SWITCH, HG FUSES,

TRANSFORMERS, LIGHTENING ARRESTORS,

DISTRIBUTION BOX. OF 10 METERS 270 KGAND PSC

POLES INCLUDING EXCAVATION OF PITS AND

REFILLING OF EARTH, CARTING OF TRANSFORMERS

FROMSTORES TO SITE, FIXING OF CHANNELS,

SUPPORTING ANGLES,BRACINGS CROSS ARMS

CLAMPS, ANTI-CLIMBING DEVICES,DANGER BOARDS,

CONDUCTOR AND CABLE WIRING ETC.COMPLETE

AND PAINTING OF FABRICATED MATERIALS USED ON

THE POLES AND NUMBERING WITH COST OF PAINT

AS PER STANDARD SPECIFICATION BUT EXCLUDING

ERECTION OF GUY SETS AND EARTHING.

DISMENTALLING OF 8 MTR PSC POLE WITH

CREDITING OF FABRICATION AT STORE & STACKING

OF POLE SAFELY ON ROAD SIDE OR CREDITING TO

DEPARTMENTAL STORE

DISMENTALLING OF 10 MTR PSC POLE WITH

CREDITING OF FABRICATION AT STORE & STACKING

OF POLE SAFELY ON ROAD SIDE OR CREDITING TO

DEPARTMENTAL STORE

DISMENTALLING OF TRANSFORMER CENTRE (8 MTR

PSC POLE) (WITH TRANSFORMER) WITH CREDITING

35 9926000035 OF FABRICATION & TRANSFORMER AT STORE & No. 3975

STACKING OF POLE SAFELY ON ROAD SIDE OR

CREDITING TO DEPARTMENTAL STORE

DISMENTALLING OF TRANSFORMER CENTRE (8 MTR

PSC POLE) (WITHOUT TRANSFORMER) WITH

36 9926000036 CREDITING OF FABRICATION AT STORE & STACKING No. 2701

OF POLE SAFELY ON ROAD SIDE OR CREDITING TO

DEPARTMENTAL STORE

STRINGING OF LT ABC OF 1*35 SQ MM + 1*25 SQ MM

INCLUDING FITTING OF ALL ACESSARIES I.E. SPECIAL

DESIGN SUSPENSION / TENSION CLAMP, FIXING OF

CROSS ARM, LT SHACKLE INSULATOR ETC. FOR

FIXING OF MESSENGER WIRE AND TO PROVIDE

SERVICE CONNECTION ON AERIAL BUNCH CABLE BY

INSULATED PIERCEING CONNECTORS THROUGH

SERVICE CONNECTION BOX COMPLETE AS

REQUIRED & DIRECTED BY ENGINEER IN CHARGE.

STRINGING OF LT ABC OF 3*50 SQ MM +1*25 SQ

MM+1*35 SQ MM INCLUDING FITTING OF ALL

ACESSARIES I.E. SPECIAL DESIGN SUSPENSION /

TENSION CLAMP, FIXING OF CROSS ARM, LT

38 9926000038 SHACKLE INSULATOR ETC. FOR FIXING OF KM 12330

MESSENGER WIRE AND TO PROVIDE SERVICE

CONNECTION ON AERIAL BUNCH CABLE BY

INSULATED PIERCEING CONNECTORS THROUGH

SERVICE CONNECTION BOX COMPLETE AS

REQUIRED & DIRECTED BY ENGINEER IN CHARGE.

STRINGING OF 11KV ABC OF 3*95 SQ MM +80 SQ MM

INCLUDING FITTING OF ALL ACESSARIES I.E. SPECIAL

DESIGN SUSPENSION / TENSION CLAMP, FIXING OF

CROSS ARM, BINDING TO PIN INSULATOR,PREPARING

SHACKLE POINT,JUMPERS ETC. AS REQUIRED &

DIRECTED BY ENGINEER IN CHARGE

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

STRINGING OF 22 KV ABC OF 3*70 SQ MM +95 SQ MM

INCLUDING FITTING OF ALL ACESSARIES I.E. SPECIAL

DESIGN SUSPENSION / TENSION CLAMP, FIXING OF

CROSS ARM, BINDING TO PIN INSULATOR,PREPARING

SHACKLE POINT,JUMPERS ETC. AS REQUIRED AND

DIRECTED BY ENGINEER IN CHARGE

STRINGING OF LT ABC OF 2*50 SQ MM +1*25 SQ MM+

35 SQ MM INCLUDING FITTING OF ALL ACESSARIES

I.E. SPECIAL DESIGN SUSPENSION / TENSION CLAMP,

FIXING OF CROSS ARM, LT SHACKLE INSULATOR ETC.

41 9926000041 FOR FIXING OF MESSENGER WIRE AND TO PROVIDE KM 9863

SERVICE CONNECTION ON AERIAL BUNCH CABLE BY

INSULATED PIERCEING CONNECTORS THROUGH

SERVICE CONNECTION BOX COMPLETE AS

REQUIRED & DIRECTED BY ENGINEER IN CHARGE.

DISMENTALING OF RSJ (9/11 METER) POLE AND

CREDITING THE OLD MATERIAL TO STORE

DISMENTALING OF TRANSFORMER CENTER ON

10MTR,270KG PSC POLE(WITHOUT TRANSFORMER)

43 9926000043 WITH CREDITING OF FABRICATION AT STORE AND No. 2828

STACKING OF POLE SAFELY ON ROAD SIDE OR

CREDITING TO DEPARTMENTAL STORE

DISMENTALING OF TRANSFORMER CENTER ON

10MTR,270KG PSC POLE(WITH TRANSFORMER) WITH

44 9926000044 CREDITING OF FABRICATION AT STORE AND No. 5332

STACKING OF POLE SAFELY ON ROAD SIDE OR

CREDITING TO DEPARTMENTAL STORE

DISMENTLING OF 11KV ABC OF 3*95 SQ MM +80 SQ

45 9926000045 MM AND CREDITING FITTING OF ALL ACESSARIES KM 20515

AND FABRICATION TO DEPARTMENTAL STORE

DISMENTLING OF 22 KV ABC OF 3*70 SQ MM +95 SQ

46 9926000046 MM AND CREDITING FITTING OF ALL ACESSARIES KM 25643

AND FABRICATION TO DEPARTMENTAL STORE

DISMENTALING OF LT ABC OF 1*35 SQ MM + 1*25 SQ

MM AND CREDITING FITTING OF ALL ACESSARIES TO

DEPARTMENTAL STORE.

DISMENTALING OF LT ABC OF 3*50 SQ MM +1*25 SQ

MM+1*35 SQ MM AND CREDITING FITTING OF ALL

ACESSARIES TO DEPARTMENTAL STORE.

DISMENTALING OF LT ABC OF 2*50 SQ MM +1*25 SQ

MM+ 35 SQ MM AND CREDITING FITTING OF ALL

ACESSARIES TO DEPARTMENTAL STORE.

RESTRINGING OF ALL TYPE OF CONDUCTOR (EXCEPT

DOG CONDUCTOR) FOR 11/22KV & LT LINES ONE COND

INCLUDING FIXING OF INSULATORS, BINDING PER KM

RESTRINGING OF DOG CONDUCTOR FOR 11/22KV HT ONE COND

51 9926000051 LINES INCLUDING , BINDING JUMPERING ETC. 3129

LABOUR CHARGE FOR THE INSTALLATION OF NEW

DTR METER. (METER WILL BE PROVIDED BY DGVCL)

LABOUR CHARGE FOR THE REPLACEMENT OF DTR

53 9926000053 METER AND OLD METER SHOULD BE CREDITED TO No. 531

SDN STORE. (METER WILL BE PROVIDED BY DGVCL)

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

LABOUR CHARGE FOR PROVIDING CT COIL FOR DTR

54 9926000054 METER CONNECTION. (CT COIL WILL BE PROVIDED PER CT 85

LABOUR CHARGE FOR REPLACEMENT OF CT COIL

FOR DTR METER CONNECTION AND OLD CT SHOULD

BE CREDITED TO SDN STORE. (CT COIL WILL BE

PROVIDED BY DGVCL)

LABOUR CHARGE FOR FIXING OF MMB FOR DTR

METER (MMB WILL BE PROVIDED BY DGVCL)

LABOUR CHARGE FOR REPLACEMENT OF DTR METER

BOX. (METER WILL BE PROVIDED BY DGVCL)

PROVIDING / REPLACEMENT OF 1.5 SQ MM 10 CORE

58 9926000058 COPPER CABLE 3.5 METER (CABLE TO BE PROVIDED No. 1840

LABOUR CHARGE FOR PROVIDING/RECONNECTION

59 9926000059 OF TERMINAL CONNECTION WITH PROPER SIZE OF 15

LUGS. (LUGS COST IS BORNE BY AGENCY)

LABOUR CHARGE FOR THE SPOT READING OF DTR

METER WITH DETAIL SURVEY OF DEFECT IF ANY. A

DULY SIGN COPY BY SURVEYOR PERSON OF

AGENCY IN PRO-FORMA REPORT SHOULD BE

SUBMITTED TO SDN OFFICE.(* ONLY IF ALL

PARAMETER OF VOLTAGE, CURRENT & LOAD AS

SHOWN IN PER-FORMA IS FILLED) AS PER THE

INSTRUCTION OF ENGINEER IN-CHARGE.

LABOUR CHARGE FOR THE SPOT READING OF DTR

METER WITH DETAIL SURVEY OF DEFECT IF ANY. A

DULY SIGN COPY BY SURVEYOR PERSON OF

61 9926000061 AGENCY IN PRO-FORMA REPORT SHOULD BE PER DTR 30

SUBMITTED TO SDN OFFICE. (DULY FILL PER-FORMA

IN FAULT CONDITION IN WHICH READING PARAMETER

IS NOT SHOWN IN METER)

INSTALLATION OF DTR METER INCLUDING METER

BOX, PROVIDING & FIXING OF 1.5SQ MM SINGLE

STRAND 10 CORE ARMOURED COPPER CABLE

(3.5METER), TERMINATION IN METER & COIL ETC.

(METER, METER BOX, C.T./P.T. COIL WILL BE

PROVIDED BY DGVCL)

INSTALLATION OF DTR METER INCLUDING METER

BOX, TERMINATION IN METER & COIL ETC. (WITHOUT

10CORE COPPER CABLE) (METER, METER BOX,

C.T./P.T. COIL WILL BE PROVIDED BY DGVCL)

Binding of messanger Conductorat with a distance not more

64 9926000064 than 0.75 mtr with 6 turns minimum on XLPE Cable with No

single strand binding wire (including cost of binding wire)

Supply and Installation of 11/22 kV Distribution

Transformers HT Terminal protector (UV Resistance) with

using 95/120/150 sq.mm long barrel aluminum lug. (1Set =

3 Nos i.e. on R, Y, B)

Supply & Installation of HT EPR Tap on 11/22 kV

Distribution Transformer with replacement of bare conductor

by HT ABC conductor (DO bottom side to transformer) after

removal of semi conductor by HT ABC (6 inch both side).

HT ABC to be supplied by DGVCL. (1Set = 3 Nos i.e. on R,

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

Supply, Installation, Testing and Commissioning of

Maintenance Free, Ready Capsule, Pipe-In-Cage (Pic)

67 9926000088 Type, Earth Electrodes for HT Feeder Pole Having 2000 No

mm Electrode Length as per the Tender Specifications and

Drawing. (All Materials Will Be Supplied By Agency)

Supply, Installation, Testing and Commissioning of

Maintenance Free, Ready Capsule, Pipe-In-Cage (Pic)

68 9926000089 Type, Earth Electrodes for HT Feeder Pole Having 3000 No

mm Electrode Length as per the Tender Specifications And

Drawing. (All Materials Will Be Supplied By Agency)

Supply and Installation of 25 X 3 mm GI Strip having hot

dip- galvanized-zinc coating of 80-100 microns without any

joints or welding. Both the end of the GI strip should be

connected with GI nut bolts and required fabrication work for

69 9926000090 giving separate earthing connections to(1) Neutral of the Meter

transformer(2) MS structures of the transformer center

(Approximately 25 meter GI strip per transformer centre- as

per requirement and instruction of Engineer in- charge) (All

Materials will be supplied by Agency)

Supply and Installation of uPVC standard make Pipe of

1.25" diameter for covering GI strip with UV protected Cable

Ties of 550 X 7.6 mm size to bind with pole

face(Approximately 25 meter uPVC pipe for GI strip

covering per transformer centre -as per requirement and

instruction of Engineer in-charge.

Supply & fixing of upto 33 kV Conductor sleeve for Busbar

to Drop out Fuse and Drop

71 9926000093 out fuse to Transformer H.T. including Busbar (12 mm Per TC

sleeve) as per technical

specification. (All Materials will be supplied by Agency)

Supply & fixing of upto 33 kV Conductor sleeve for Busbar

to Drop out Fuse and Drop

72 9926000100 out fuse to Transformer H.T. without Busbar (12 mm sleeve) Per TC

as per technical

specification. (All Materials will be supplied by Agency)

Supply & fixing of upto 33 kV Conductor sleeve for Busbar

to Drop out Fuse and Drop

73 9926000094 out fuse to Transformer H.T. including Busbar(15 mm Per TC

sleeve) as per technical

specification. (All Materials will be supplied by Agency)

Supply & fixing of upto 33 kV Conductor sleeve for Busbar

to Drop out Fuse and Drop

74 9926000101 out fuse to Transformer H.T. without Busbar(15 mm sleeve) Per TC

as per technical

specification. (All Materials will be supplied by Agency)

Supply & fixing of Disc type Red Color FRP(Non-

flammable) material with Weather

resistant, Non-conductive bird guard OD=300 MM, ID=33

MM, Width =1.25 MM, one

side cut from ID to OD. (All Materials will be supplied by

Providing and fixing of LT Terminal protectors i.e. Re-

useable boot (LT Side 1.1 kV) including LT (1.1 kV)

insulating taps. All live part at LT side shall be covered with

fixing of LT insulating taps.

77 Nylon Net around Transformer Center

77.1 9926000097 Nylon Net (12 * 15 ft) Per Net

77.2 9926000098 Nylon Dori Per TC

Labour charge for fitting Nylon Net (All fabricated material

for fitting nylon net shall be provided by DGVCL)

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

Erection Schedule B2

1 9924000001 Cutting of Tree branches surounding HT/LT line Per Tree 57

Replacement of old jumpers & providing new double

jumpers with 8" binding & capsuling with PVC pipe etc

3 9924000005 Support pole for Stay PSC/STP/RSJ No. 633

4 9924000006 Pin binding of conductor 11/22kv Pin insulator No. 18

Pin binding of conductor 11/22kv Pin insulator per pole in

costle area with cleaning .

6 9924000008 Pin binding of conductor LT shakel insulator No. 14

7 9924000009 Replacement of one/both disc.insulator at strain pole No. 161

8 9924000010 Replacement of LT shackle insulator at cut point No. 31

9 9924000011 Refixing of V cross Arm No. 61

10 9924000012 Replacement of V cross Arm No. 210

11 9924000013 Refixing of Top fitting in proper position No. 41

12 9924000014 Replacement of Top fitting No. 51

13 9924000015 Replacement of LT cross Arm No. 105

Providing DO fuse on DP with carting & jumpuring(ONE DO

Numburing of pole with paint by preparing back ground of

15 9924000017 one colour and have lettering(height 3" * width 0.5") using No. 46

16 9924000018 Fixing of MMB(1PH.) at consumer end No. 86

17 9924000019 Fixing of MMB(3PH.) at consumer end No. 128

18 9924000020 Replacement of (1ph.) meter for Urban area No. 51

19 9924000021 Replacement of (1ph.) meter for Rural area No. 74

painting consumer no. on MMB (Urban) (with letter size

height 40mm* width 8mm)

painting consumer no. on MMB (Rural) (with letter size

height 40mm* width 8mm)

22 9924000024 Replacement of deteriorated Single phase Service line No. 93

Fixing of new dist. Box with complete wiring including

clamps,nut bolts etc.

Reparing of guarding involving reshaping of bearer wire

cross lacing binding etc.

Painting of steel fabricated material of RSJ DO DP structure

Painting of steel fabricated material of RSJ pole mounted

transformer double pole structure with paint

Painting of steel fabricated material of RSJ single pole with

painting of steel fabricated material of PSC Single pole (HT

line) with paint

painting of steel fabricated material of PSC DO DP double

pole with paint

painting of steel fabricated material of PSC double pole at

pole mounted transformer with paint

31 9924000033 Providing line seperater single phase No. 11

32 9924000034 Providing line seperater three phase No. 31

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

Replacement / Providing of stay insulator along with

adjustment of tension in stay wire

Replacement of deteriorated /providing LT dist. Box with

new up to 100KVA capacity & crediting it to store.

Replacement of deteriorated /providing LT dist. Box with

new above 100KVA capacity & crediting it to store.

36 9924000038 Adjustment of tension in stay wire No. 158

37 9924000039 Refitting of LA No. 31

Converting pin point to Shackle point including dismentaling

& restringing etc.

replacement of 11KV Pin insulator with providing new

double pin binding

replacement of 22KV Pin insulator by new 11kv pin

insulator with spares & providing new double pin binding

Providing 11kv double disc insulators with binding &

Replacement of existing 11kv conductor (all size) with new

double pin binding

43 9924000046 Plumbing of PSC Pole with straightening at pin point No. 287

44 9924000047 Plumbing of PSC Pole with straightening at tension point No. 373

Plumbing of tilted DP structure (PSC/RSJ/STP) with refilling

of stone Murrum etc.

Providing new 11kv AB /GO switch with fabrication and

insulated colour code jumper, binding, lugs etc

Replacement of old 11kv AB /GO switch with providing new

insulated jumper, binding, lugs etc

Providing cage type loop guard in verticle LT line with using

PVC reel insulators etc

Labour charges for replacement /providing of MMB &

service with all accessories for three phase connection

Labour charges for replacement /providing of MMB &

service with all accessories for single phase connection

Dismentalling of existing Dist.X'mer center(RSJ /STP

51 9924000055 POLE) 25/63/100/200 KVA with all fabrication & creditig the No. 5528

old material to store

52 9924000056 Disconnection from LT pole 1 phase No. 46

53 9924000057 Reconnection from LT pole 1 phase No. 46

( payment after receipt of R/C charges)

54 9924000058 Disconnection from LT pole 3 phase No. 66

Reconnection from LT pole 3 phase

( payment after receipt of R/C charges)

Dismentaling & removing of service line from pole &

crediting to S/dn (1 ph.)

Dismentaling & removing of service line from pole &

crediting to S/dn (3 ph.)

Reconnection of service line complete with PVC cable (1

Reconnection of service line complete with PVC cable (3

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

Providing spiral type earthing by G.I. NO 8(weight 2kg -5mtr

in length) with salt and coal 10kg each, including pvc rigid

60 9924000064 pipe 20mm dia( 1.5mtr length) to pass exposed part of G.I. No. 816

wire at consumer end with all materials, earth resistance

should be less than 2 ohms

Providing and fixing of signle core 1.5 sq mm single strand

copper insulated cable with cable nail clip for spiral type

earthing at consumer end. The end of G.I. no 8 is to be

connected by connector with copper cable of which other

61 9924000070 per meter 30

end shall be connected to the earth terminal of meter box.

This item shall be used in location where there is more

distance between earth terminal and earthing terminal of

meter. (All materials supplied by contractor)

Stringing of LT ABC of 1*35 SQ MM + 1*25 SQ MM

including fitting of all acessaries i.e. special design

suspension / tension clamp, fixing of cross arm, LT shackle

insulator etc. for fixing of messenger wire and inclusive of

62 9924000065 dismantling charge of existing bare conductor and crediting KM 8922

in to store & dismentaling of service line from LT bare

conductor and to provide service connection on Aerial

Bunch Cable by insulated pierceing connectors through

service connection box complete as required & directed by

Engineer in Charge.

Stringing of LT ABC of 3*50 SQ MM +1*25 SQ MM+1*35

SQ MM including fitting of all acessaries i.e. special design

suspension / tension clamp, fixing of cross arm, LT shackle

insulator etc. for fixing of messenger wire and inclusive of

63 9924000066 dismantling charge of existing bare conductor and crediting KM 22303

in to store & dismentaling of service line from LT bare

conductor and to provide service connection on Aerial

Bunch Cable by insulated pierceing connectors through

service connection box complete as required & directed by

Engineer in Charge.

Stringing of 11KV ABC of 3*95 SQ MM +80 SQ MM

including fitting of all acessaries i.e. special design

suspension / tension clamp, fixing of cross arm, binding to

64 9924000067 pin insulator,preparing shackle point,jumpers etc. and KM 44608

inclusive of dismantling charge of existing bare conductor

and crediting in to store complete as required & directed by

Engineer in Charge

Stringing of 22 KV ABC OF 3*70 SQ MM +95 SQ MM

including fitting of all acessaries i.e. special design

suspension / tension clamp, fixing of cross arm, binding to

65 9924000068 pin insulator,preparing shackle point,jumpers etc. and KM 55019

inclusive of dismantling charge of existing bare conductor

and crediting in to store complete as required & directed by

Engineer in Charge

Stringing of LT ABC of 2*50 SQ MM +1*25 SQ MM+ 35 SQ

MM including fitting of all acessaries i.e. special design

suspension / tension clamp, fixing of cross arm, LT shackle

insulator etc. for fixing of messenger wire and inclusive of

dismantling charge of existing bare conductor and crediting

in to store & dismentaling of service line from LT bare

conductor and to provide service connection on Aerial

Bunch Cable by insulated pierceing connectors through

service connection box complete as required & directed by

Engineer in Charge.

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

UG Work Up to 200 Mtr only in All Scheme to be

given in above work order for timely completion of

1.AS 300 Mm2 Cable Cost Data not Availble with DGVCL

and We have Proposed 300 mm2 Cable at Various

Location to Create Robust netwrok with RMU and SS

End Hence Cost Data of UGVCL Considered as Ref and

Rate Taken Accordingly as per Telephonic Instruction

GIven by Competent Authority from Circle Office

Total of Schedule B1 + B2 + B3 + B4 is Rs. TOTAL

1.DGVCL will provide key material like M.S.

materials,ABC/Bare conductors,PSC/RSJ

Poles,Insulators,Fabricated materials etc. to the contractor.

2.All fabricated items shall be fabricated as per DGVCL

approved drawing and by welding rods confirming to the

relevent ISI specification and as directed by Engineer in

3.Necessary electricity connection for fabrication items shall

be provided by DGVCL on payment of required charge for

connection & electricity bill of the same shall be paid by the

4.All the rates are inclusive of PF & Exclusive of GST

applicable time to time.

5.All steel material are to be painted as below:

(a) Scrubbing of rusted surface properly before applying

the paints on to the RSJ poles & steel fabricated materials

of RSJ/PSC poles is must required.

(b) Two coats of approved ISI mark red oxide (primer) is to

be properly painted for the RSJ poles & steel fabricated

materials of RSJ/PSC poles.

(c) Two coats of approved ISI mark silver paint (i.e. triple

mangoes or equivalent quality silver paint) is to be properly

painted on to the RSJ poles & steel fabricated materials of

1. Excavation, Drilling and Cable laying should be done

with all road safety measures such as hard barricading,

displaying “DANGER” sign and “DGVCL - Work in

Progress” on it with light reflective strips or paint. Proof of all

barricading and safety equipment need to submit.

2. Cable laying should be done through roller (not

through tractor or pulling by any other vehicles).

3. Ownership document regarding roller/pulling machine

and HDD machine need to submit or agreement with

agency of above narrated machine regarding work for this

tender required to submit.

4. Trail pit excavation and De-excavation should be done

simultaneously so that any chance of road accident can be

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU

Letter No: DGVCLSDUR/0262/06/2026 Approved Date: 12-06-2026

5. Three no of Polymer cleat should be provided on rising

cable for proper fitting and if it is not feasible to provide third

polymer cleat at the bottom than two nos of polymer cleat

Executive Engineer (Tech)

Technical on upper side and strap strip on bottom end required to

install for proper fitting of rising cable. DGVCL

Sachin Division

6. 100% videography of cable laying along with landmark

location of cable laying required to be done and submit Pen

drive to the concern engineer for their verification.

7. Aluminum strip required to use to connect end of cable

at cable rising location as per instruction of Engineer in

charge. Also no joints will be allowed in GI strip for cable

Earthing and strip will be connected through GI bolts only.

8. Issues regarding ROW on field should be resolved by

contractor itself.

9. Testing & measuring equipment: - 5 KV Digital

insulation testers, Digital Earth clamp meter for

measurement of Earthing and leakage current, Digital

Rodometer with NABL accredited agency valid test

10.Earthing value & Insulation Resistance (IR) value of all

location along with Geo tagged (longitude & latitude) wise

testing and measured value photograph need to submit with

11.Depth chart should be provided at every 100 meter with

mentioning landmark.

12. Partial Discharge test to be carried out on sample part of

cable before charging as decided by in charge engineer.

13. Qualified cable jointer with Minimum five years of

experience required with necessary certification regarding

qualification and specific experience.

14. Performance Bank Guaranty required to submit 5% of

tender value for two years against cable joint failure.

Moreover, cable joint failure or end termination failure will

have to repair within 24 Hrs for 2 years of guaranty period.

15. Fixing of mechanical protection HDPE pipe at rising

should be properly buried as per specification.

16. Fixing of Route marker strictly as per specification.

17. Minimum annual Turnover should be at least tender

estimated value and in addition to CVC guideline narrated in

tender for UG cable laying work.

18. Marking of feeder name, direction and location on cable

is compulsory during final scrutiny to declare work

19. End termination and straight joint kit should be of

premium quality as specified in Annexure-2. Technical

specifications for the same to be submitted along with bid.

20. Cable straight joint should be done with mid span joint

instead of long barrel Lug.

21. Agreement with vendor of cable joint kit and End

termination kit to supply for this tender for concern bidder

should be submit at the time of bidding.

File No: DGVCLSDUR/MSC/e-file/4523/2026/0739/Billing

Approved By: Executive Engineer,Technical,DGVCLDSRTU