Upgradation of Sewerage Treatment Plant Sunder Nagar and Providing Sewerage Connectivity to left out area under MC Sunder Nagar Town Distt Mandi HP

Amount

Excavation in foundation and trenches etc.(in pipes and pits) in all kinds of soils such as pick work, jumper work, blasting in soft/hard rock, chiselling/wedging out of rock/where blasting prohibited) saturated soil stacking the excavated soil as directed by the Engineer-in-charge clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinth sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer –in-charge in all leads and lifts.

Providing and laying cement concrete 1:3:6 (1Cement:3sand:6 graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form work foundation and plinth in all leads and lifts

Providing and laying cement concrete 1:1½:3 (1Cement:1½ sand:3 graded stone aggregate 20mm nominal size) and curing complete excluding the cost of form work & reinforcement for reinforced concrete work in :(a) Foundation,footing.bases of columns & the like & the mass concrete.

(b) Wall (any thickness,but not less than 0.10 mtr.thickness) attached pilasters,buttresses,plinth & string courses etc. from top of foundation level upto floor two level (i) Floor two level to floor three level (ii) Floor three level to floor four level (iii) Floor four level to floor five level.

( c) Column,pillars,posts & struts upto floor two level (i) floor two level to floor three level)

(ii) Floor three level to floor four level

(d) Lintels,beams gorders bressumers & cantilevers upto floor two level (i) Floor two level to floor three level

(e) Slab upto floor two level (i) Floor two level to floor three level

(ii) Floor three level to floor four level

(f) Suspended floors,roofs,landings.etc.upto floor two level (i) floor two level to floor three level (ii) floor three level to floor four level

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring, shuttering , strutting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor to ceiling not exceeding 4meters and removal of the same for insitu reinforced concrete and plain complete in all respect in all leads and lifts.(i) Foundation,footing,bases of columns etc.and mass concrete.

Flat surface such as soffits of suspended floors,roofs,landing and the like

Vertical surfaces such as walls (any thickness) partitions and the like i/c attached pillasres buttresses,plinth & string courses and the like uptro 4.00 mtrs. (ii) For vertical surfaces of tank

Columns,pillars.posts & struts

Beyond 4.00 mtrs.

Beams,cantilever,girders & lintels.Sides & soffits of beams,beam haunchings ,cantilevers, bressumers,& lintels not exceeding 1.00 mtr.depth in all ht.from floor.

Providing Tor steel reinforcement for RCC work including bending,binding & placing in position complete upto floor two level.

Providing in RCC work smooth finishing of the exposed surface with cement mortor 1:3 (1cement :3Sand) complete in all respect within all leads & lifts.

Finishing wall with water proofing cement paint of approved brand & manufacture & of required shade on undecorated wall surfaces (two coats) to give an even shade after thotoughly brushing the surface to remove all dirt & remains of loose powdered material complete in all respect in all leads and lifts.

Manufacturing, febrication & fixing of M.S. man hole cover of 0.60x.60 m size made of M.S. Sheet 2.0 mm thick with M.S. angle 35x35x5mm thick with hinges one side and sliding door bolt for locking arrangement i/c cutting, welding and priming & Painting two coats of anamel paint sky complete in all respect to the entire satisfaction of the Engineer-in-charge.

Laying, jointing and testing in trenches to be levelled to grades, IS marked GI flanged pipes of following diameters confirming to IS: 1239-1990 (Part-II) (latest with upto date ammendments) having minimum wall thickness as for class of pipe specified below jointed with flanges conforming to tables as specified below of BIS 6392-1971 ( latest with upto date ammendments) welded at both ends of pipe according to relevant BIS standards and detailed specifications, provided with nuts & bolts of required sizes, 3mm thick compressed asbestos fiber gasket of synthetic rubber gasket confirming to relevant BIS codes including all kinds of flanged short pieces, bends, tees and other specials etc. made from parent tubes and welded with flanges of tables as applicable for the particular reach & of technical specifications as per site conditions including flushing cleaning & hydraulic testing as per direction of the Engineer-in-charge.(i) 100mm dia (Medium class) Flange table-17 wall thickness 4.50mm

Steel work welded in built up sections,trusses & framed work i/c cutting, hoisting,fixing in position & applying a priming coat of red paint.In grating,framed guard bars,ladders,railing,brackets & similar works complete in all respect in all leadss and lifts.

Laying, jointing and testing of GMS tube (screwed and socked) in trenches of following diameter light grade including providing and fixing tube fittings such as bends, tees, air valves, unions and collars etc. complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge (earth work in trenches to be measured and paid for separately). (i) 20mm dia

Providing and fixing of double flanged cast iron sluice valve Class-PN-1 conforming to IS: 780-1984 of Leader/Bhel/Kirloskar /Fources/ Gled/ Pelican/Kartar make of following dias for the pipe line capable to withstanding normal seat pressure including cutting, welding,providing and fixing rubber/asbestos sheet of maximum thickness 3mm as per IS 2712-1979 and providing and fixing MS flange as per Table-17 with required number of nuts and bolts including carriage of material in all leads and lifts.(i) 125mm dia

Manufacturing of GI bend from parent tube with butt welding of following dia with diesel generator set at site of work according required degree to site requirement in minimum three layers to make the joint leak proof accordingly to relevant BIS standard/approved specifications and to the entire satisfaction of the Engineer-in-charge.(i) 100mm dia

Constructing chamber for sluice valve, with CI surface box 100 mm top dia.,160 mm bottom dia.&180 mm deep (inside) with chained lid RCC top 1:2:4 mix (1 cement :2 Sand :4 graded stone aggregate 20 mm nominal size ) 100 mm thick foundation conc.1:5:10 mix (1cement : 5 sand : 10 graded stone aggregate 40 mm nominal size) & inside plastering with cement mortor 1:3 (1 Cement : 3 Sand ) finished with a floating coat of neat cment i/c curing complete.600 x 600 x 750 mm inside size With 150mm th.walls of RCC1:2:4(1cement 2sand:4graded stone aggregate 20 mm nominal size) complete with form work & reinforcement with 6 mm bars at not exceeding 150 mm centres both ways.

P/Fixing of below items requiredfor OHSR complete in all respect (a)Lightening Conductor

(b) Water measurement gauge

( c) Vent Pipe i/c CI cowl complete

( d) Flanged bell mouth a/w puddle collars

(e) Expansion joints

Brick work using common burunt clay building bricks in foundation and plinth in cement mortor 1:6 (1 cement : 6 sand) complete in all respect in all leads and lifts

Providing wood work in frames of door & windows clearstorey windows & other wrough frames in 2nd class Deodar wood complete in all respect in all leads and lifts.

Providing 40x3mm flat iron hold fast 40cm long including fixing to frame with 10mm dia bolts, nuts and wooden plugs and embending in CC block 30x10x15cm 1:3:6 (1cement:3 sand:6 graded crushed stone aggregate 20mm nominal size as directed in all leads and lifts and to the entire stisfaction of the Engineer -in -Charge.

Providing and fixing panneled glazed or panelled and glazed shutters for doors, windows and clerestory windows,including black enamelled iron butt hinges with necessary screws. 45 mm thick.2nd class deodar wood.

Providing & fixing M.S. grills of required pattern in wooden frame of window etc.with M.S. flats, square or round barswith round headedbolts and nuts by screws plain grills.

Boulder filling under floor complete in all respect in all leads and lifts.

Cement concrete flooring 1:2:4 (1 cement : 2 sand :4 graded stone aggregate 20 mm nominal size) laid in one layer finished with a floating of neat cement.40 mm thick

6mm cement plaster to ceiling in CM 1:3 ( 1Cement :3 Sand) complete in all respect in all leads and lifts.

15mm cement plaster in single coat on rough side of brick/ concrete stone walls for interior plastering upto floor two levels including arrises internal rounded angles chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:3(1cement:3 sand) in all leads and lifts.

Applying Acrylic Washable emulsion Spectrum quartz king or equivalent finish for interior painting with brushes plain smooth finish composed of acrylic polymere in emulsion inorganic/special pigment siliceous aggregate anti fungicides anti rusting & foaming in two coats i/c necessary putty to give smooth even surface, sand papered smooth complete.

Applying priming coat on new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil,greese,dirt and other foreign matters,sand papering and knotting.Ready mixed paint brushing wood primer pink.

Painting two coats (excluding priming coat) on new wood and wood based surfaces,with enamel paint to give an even shade including cleaningthe surface of dirt ,dust and other foreign matters sand papering and stopping with enamel paint other than white

Providing and fixing anodised MS sliding door bolts with bolts and nuts screws etc. complete.(i) 250 *16 mm

Providing and fixing anodised MS tower bolts ( barrel type) with screws etc. complete.(i) 250*10 mm

Providing ad fixing anodised MS handles with necessary screws etc. complete. 125mm

Providing & fixing oxidised M.S. hooks & eye 250 mm

Structure Design of Over Head Store Tank of 25000 Ltr. Cap. as per relevant is codes including sub soil investigation.

Providing, fixing gun metal wheel valve ordinary split, tapper edge, non rising spindle gate valve of 1st class for cold service (temprature not exceeding 45degree centigrade) screwed type as per IS:778-1984 and to the entire satisfaction of the Engineer-in-charge in all leads and lifts.(i) 32mm dia

Providing and supplyinig Gun Metal Gate Valve (Class-I) confirming to IS: 778-1984 in (reaffirmed 2007) incorporating amendment 1,2 and 3 of following dia within all leads and lifts as per the entire satisfaction of the Engineer-in-charge (i) 80mm dia

Wiring for light point/fan point/ exhaust fan/ call bell point wiwth 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and eahing the light point with 1.5 Sq. mm HRFRLS/PVC insulated single core copper conductor cable as required Group C.

Wiring for light plug with 2 x 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. 1.5 Sq. mm HRFRLS/PVC insulated sigle core copper conductor cable for earthing as required.

Wiring for power plug with 2x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. Sq. mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.

Supplying & fixing metal box of following sizes (nominal size) on surface or in recess suitable for fixing phenolic laminated sheet cover in front including painting etc. as required(i) 200mm x 150mmx 75mm deep

P/F 5 Pin 5/6 amps socket outlet porcelain base piano type

P/F 6 Pin 5/6 amps socket outlet porcelain base/ piano type

Providing, Installation, tesing and commissioning of ceiling fan 1200 mm sweep, (Category-A) with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable , including providing and fixing phenolic laminated sheet cove on the fan box and eathing etc. as required

Providing and fixing following type of surface mounting decorative mirror optics luminaire with powder coated CRCA sheet housing, low glare aluminium mirror reflector, prewired with 110 V starter & 36/40 W copper ballast for housing CFL (but accessories, connections, testing and commissioning etc. as required 2x11 watt-CFL (Category A)

Supplying and fixing of bulk head fitting of all sizes and shapes, containing one no thread type CFL lamp holder (s) complete with all accessories but excluding CFL lamp including making connections. Testing etc. as required(i) Bulk head fitting, CFL type (Category-A)

Supplying and fixing of 20 mm diameter PVC conduit along with the accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required :-

Tulsi Ram

JBN Infra

Royal Construction Company