SPECIAL REPAIRS TO SOUTH WING OF DSC LINE AND DINING HALL BUILDING No P-163 AT NAVAL BASE, KOCHI

Amount

Taking down of existing roof treatment consisting of screed bed plaster tar felts etc and removal of dismantled materials complete all as specified and directed.

M&L Cement concrete Type B0 1:2:4 (12.5mm graded aggregate ) in levelling course of concrete in roof slab all as specified and as directed.

Supply and fix Pre- painted galvalume roofing system aluminum zinc coating GI based corrugated steel sheet 0.50 mm total thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws shall be continuous with no joints complete all as specified and as directed .

M&L for Providing and applying pitch free polyurethane water proof coating using Fosroc Nitoproof 600 or equivalent, over dry surface at 1.5mm thick in 2 coats with interval period of 6 hours over a substrate at a coverage rate of 2 kg/sqm using spray/squeegee/roller/brush. Waterproofing coating shall have the elongation of 200% (ASTM D412-90, tear resistance of >7N (ASTM D 624-00), and tensile strength of > 1.5N/mm2 (ASTM D412-90) and it should have a solid content of 80-85%. Sprinkle fine aggregate straight after the application of Nitoproof 600 PF to get the mechanical key for the protective plastering.

M&L for Rolled sections (Tublar sections) as in main and cross beams, hip and jack rafters; purlins , wall framing ,where connected to common rafters and fixed with angle cleats or other connecting plates complete all as specified and directed.

M&L for preparation of new Surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of anti corrosive Epoxy paint over a coat of Epoxy primer on steel surfaces complete all as specified and directed. (Make-Asian Apcolite or Equal from Berger, Nerolac)

Demolition of cement concrete (Un-reinforced) in ground floors and pavings n.exc 15cm thick (above or below GL) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for joint free coloured Non Skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.18 but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over 15mm thick screed bed of CM 1:6 all as specified and directed.

M&L for Glazed ceramic joint free tiles in vertical surface 600x300x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 mm thick rendering CM 1:3 complete all as specified and directed.

M&L for 18 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like over 15 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L for mirror polished kota stone slab flooring 20-25mm thick over 15mm thick cement screed base in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. Note:- Kota stone shall be prepolished to mirror finish

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 10mm thick rendering in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) 25 mm thick as in Sub base complete all as specified and directed.

Taking down cement plaster on brick/ concrete walls incl raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for cement plaster 10 mm thick in cement mortar 1:6 finished even and smooth without using extra cement for internal faces of walls complete all as specified and directed.

M&l for rendering 8mm thick in CM 1:4 using liquid WPC over 12mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces finished even & fair without using extra cement complete all as directed. Note: Water proofing compound shall be paid separately.

Supply only Liquid water proofing compound complete all as specified and directed.

M&L for two coats of oil bound distemper over a coat of 1.5mm thick wall care putty to newly plastered surface including preparation of surfaces over a coat of suitable primer complete all as specified and directed .

M&L for preparation new plastered external wall surfaces and apply one coat of water proofing primer to antifungal paint over 1.5mm thick exterior wall care putty and allowed to dry overnight before applying first coat of wethaer proof (anti fungal paint) complete all as specified and as directed. Note :- Before application of primer coat, the moisture of the wall surface shall be checked with a moisture meter .

M&L for complete removal of existing suracfe finishes of external wall,preparation of surface and apply one coat of water proofing primer to anti fungal paint over 1.5mm thick exterior wall care putty and allowed to dry over night before applying first coat of weather proof (anti fungal paint) complete all as specified and as directed. Note :- Before application of primer coat, the moisture of the wall surface shall be checked with a moisture meter .

M&L for application of first coat of weather proof paint (anti fungal paint) ( Asian paint apex ultima protek or equivalent of Berger /Nerolac )on primed wall surface using spray application or mechanical means, to get a smooth and tint free surface and allowed to dry for at least 8 hrs/ overnight to receive second coat of acrylic exterior emulsion paint complete all as specified and as directed.

M&L for application of second coat of weather proof paint (anti fungal paint) ( Asian paint apex ultima protek or equivalent of Berger /Nerolac ) over first coat on wall surface using spray application or mechanical means, to get a smooth and tint free surface complete all as specified and as directed. Note for item No. 20 to 23: (i) The old surface shall prepared using mechanical ways I.e., jet-spray, grinding etc., in such a manner that there should not be any impression of dent, all cracks to be filled with crack filler, water proofing primer in shaft/dampness areas and it should be made even all as per manufacturers instruction before application of putty base primer/base coat and emulsion paint. (ii). The work shall be got executed through authorised applicator of approved manufacturer. Authorisation letter of applicator shall be produced by the contractor before starting the work (iii) The contractor shall submit performance Guarantee certificate provided by manufacturer for a period of FIVE years from the certified date of completion of entire work. (iv) After preparation of surface exterior putty to be applied to make surface even to receive base coat and two coat of emulsion paint, the same shall be got approved by GE before each stage.

Dismantling wall and ceiling boards or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

Supply, providing and fixing suspended false ceiling consisting of 12mm thick calcium silicate seamless board suspended on GI framework with staggered joints, GI framework to consist GI perimeter channel 25mmX20mm of 22 gauge along perimeter of false ceiling. Channel section of 50X25mm of 22 gauge and at 300mm centre to centre throghout one way fixed with screw/nut bolt and other direction 40x15 mm 22 gauge channel provided with interlocking with GI cleat and expansion fastnors including hangers 6mm dia GI fixed to roof truss, Boards are to be joined and finished so as to have a flush look which includes finishing the tapered and square edges of the calcium silicate board with joining compound paper tape and two coat of Oil bound distemper over one coat of primer and one layer of putty 1mm thick in suitable for calcium silicate board( as per the recommendations/ practice) ncluding necessary scaf folding and shuttering complete as directed as specified and directed by Engr-in-Charge.

Taking down chowkats with shutter n.exc 1.5 Sqm each (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats with shutter exc 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) complete all as specified and directed.

M & L Plain solid straight chowkats IInd class hard wood wrought framed rebated on the solid rounded or chamferred put together with glues pinned at joints etc complete all as specified and directed.

S&F 35 mm thick factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated as 2nd class HW style and rails complete all as specified and directed.

S&F 2nd class hard wood, 35 mm thick Glazed & skeleton shutters, open rebated & prepared to receive glass, gauze, etc. divided into squares with plain chamfered mitered and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, section 8, clause 8.20 (a); supplied & fitted to Chowkats complete all as specified and directed.

S&F powder coated anodised aluminium frame for doors, windows, ventilators, partitions with one or more rebates including jointing cleats for fixing etc complete all as specified and directed.

M&L for 18/19 mm thick pre-laminated particle board , interior grade, prelaminated both side docorative choice lamination , fixed with screws to aluminium frame work complete all as specified and directed.

S&F Sheet glass ordinary quality exc 5.5 mm thick fixed with rubber beadings to aluminium frame work n exc 0.50 sqm in each pane complete all as specified and directed.

S&F hydraulic door closer designation No:03 universal type suitable for door shutters of 851 to 1000 mm in width aluminium extruded section body all as specified complete all as specified and directed.

S&F powder coated aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc.complete all as specified and directed.

S & F Powder coated aluminium window and ventilator shutters, fixed type/sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified Make : JINDAL or equivalent section from HINDALCO/INDALCO/MS AJIT IND PVT LTD

S&F powder coated aluminium Deco grill of design DG-104 pattern made out of 10mm dia rod fixed with and including stranded aluminium frame of 'F' section of size 23.4X15.3X1.4 mm thick all as per manufactures instruction complete all as specified and as directed.

S&F Sheet glass ordinary quality exc 5.5 mm thick fixed with rubber beadings to aluminium frame work exc 0.50 sqm in each pane complete all as specified and directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for preparation of new wooden surface exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50 x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying & fixing in opening as per specification & drawing.

S&F factory made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile) with wood free EPS, with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front Face & 2mm Plain colour PVC sheet on back face, S&F in frame at site as per specification & drawing all as specified.

S&F brass door springs (Capsule type) 300 mm long and including roller and roller plate complete all as specified and directed.

S&F extruded aluminium alloy handles, 150 mm long fabricated type anodised complete all as specified and directed.

S&F alluminium, anodised, barrel tower bolts of extruded section of size 150 mm long complete all as specified and directed.

S&F aluminum anodoised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts etc complete of size 300mm

S&F 125mm Stainless Steel Butt hinges complete all as specified and directed.

Cutting holes in brick wall built in CM for inserting hold fast etc and making good dismantled portion in CM 1:3 or PCC 1:2:4 type B1 with depth of embeded purlin exc half brick but n.exc one brick complete all as specified and directed.

M&L PCC 1:2:4 type B1 ( with 20mm graded aggregate) as in anchorage block for hold fast complete all as specified and directed.

S & F mild steel framed works, framed and hung as in gates incl pintle hinges, holdfasts, stops, hand made sliding bolts fixed in walls/pillars complete all as specified and directed.

Treating to back of chowkats are tarred exc 0.1 Sqm but n.exc 0.5 Sqm each complete all as specified and directed.

Treating to holdfasts n.exc 0.1 Sqm each complete all as specified and directed.

Demolition and breaking up AC drain pipes 100 mm dia ( Salt glazed ware, AC or reinforced concrete) set in cement mortar 1:4 complete all as specified and directed.

S&F PVC (SWR) pipes in 75mm. Dis single socketed, in any length with rubber ring joints, Fixed in wall/floor complete all as specified and directed.

S&F PVC (SWR) pipes (110mm) single socketed, in any length with rubber ring joints, fixed to wall/floor complete all as specified and directed.

PVC (SWR) bends with acces door any radius 110mm complete all as specified and directed.

PVC (SWR) bends with access door any radius 75mm complete all as specified and directed.

S & F for 110mm PVC (SWR) vent cowl complete all as specified and directed.

PVC (SWR) junction single, (Single 'T') equal or unequal 110mm with access door complete all as specified and directed.

PVC (SWR) junction single, (Single 'T') equal or unequal 75mm with access door complete all as specified and directed.

S&F in repairs Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste chain and plug and porcelain stopper but including brackets all as specified. Make: Parryware cat No - C0578 White Colour/ Johnson Cat No-P0519PW/ Jaguar Cat No- URS-WHT-13261

S&F in repair 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed. Make-CERAParryware Cat No - T0802A1/Johnson Cat No- T2601C4/Jaguar Cat No- ARI-39011

S&F in repairs CP brass towel rail 60cm long 20mm dia fixed complete all as specified and as directed.

S&F in repairs viterous China wash down water closet pan (pedestal pattern), white incl plastic water closet seat, closed pattern with flat bottom, cover and mild steel chromium plated or aluminised hinging device, fixing bolts, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float & handle incl brackets, PVC connections 15mm size with PTMT nuts of length 600 mm and Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and directed.Make-(EWC) Parry ware (Cat No-C844A White) or Cera (Cat No-3131 White) or Hindware (Cat No-92082 White)

S&F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repairs brass chromium plated bottle trap with inlet or outlet screwed for pipe for connection including necessary packing, union and cap (32 mm bore) complete all as specified and directed.. make Parryware Cat No- T3203A1/Johnson Cat No- T0060C/Jaguar Cat No- ALD-769L300x190

M&L for providing, 75mm thick cement concrete, Type C1, 1:3:6 (using 20mm graded aggregate) for plinth protection complete all as specified and as directed.

M&L for 10mm thick Bitumastic gola, with 80/25 bitumen and coarse sand mixture. 1:3 by weight, for joints between bays of plinth protection (for full depth of PCC) complete all as specified and as directed .

S&F 180 mm dia of PVC half round ready made eaves gutter of pressure rating 6 Kg/cm2 of approved make including necessary fitting like bend WC/ MS clips etc complete all as specified and as directed.

S&F 150 mm dia of PVC (SWR) pipe single socketed in any length with rubber joints including necessary fitting like bend WC/ MS clips etc fixed on walls complete all as specified.

M&L for complete removal of existing treatment and applying two coats of Oil bound distemper over a coat of 1.5 mm thick wall care putty complete all as specified and directed. Note:- Application of paint, primer and wall care putty shall be as per manufacturer's instruction.

Demolition of brick work / PCC block masonry built in cement mortar including all quoins, arches, pillars, etc. all as specified and as directed .

M & L formwork to sides and soffits of beams, lintels, slabs cantilevers etc complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed,

M & L RCC M 30 grade in beams, cantilevers, lintel etc complete all as specified and directed.

M & L RCC M 30 grade in slabs etc complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, lintels hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-410-W (Gde E 250) Quality A or Fe-290 (Gde E-165) complete all as specified and directed

S&F 6 to 8mm dia TMT bars in reinforcement cut to length, bent to shape required incl cranking, bending hooking and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for precast cement concrete block masonry in type C1, 1:3:6 (20 mm graded aggregate) with solid blocks exc 10 cm in width and setting in cement mortar 1:6 in foundation load bearing wall and wall complete all as specified and directed.

Mirror polishing on marble/ granite/Kota stone/ stone work where everrequired to give high gloss finish complete all as specified and directed.

S&F Stainless steel sink(Gde 304) single bowl size 3m x 0.45m x 0.30m ( made with 1mm thick SS sheet) including bracket and other fitting arrangement complete all as specified and directed.

Providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, sheet metal encl. with plug & socket etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed..

M&L point wiring with 1.5 Sqmm PVC insulated unsheathed FRLS multistranded single core copper conductor cable in PVC concealed conduit rigid non metallic ( ISI marked ) fixed concealed on wall /roof except beam, column and RCC roof including chases cutting incl 1.5 Sqmm PVC insulated copper conductor as earth continuity wire with GI flush box of suitable size with inner and outer white cover plate and frame for One light point controlled by one switch complete all as specified and directed.

All as per item No. 86 above but for One fan point / exhaust fan point controlled by one switch & regulator complete all as specified and directed.

All as per item No. 86 above but for One 5 pin 5 Amps Socket point controlled by one switch on same board complete all as specified and directed.

All as per item No. 86 above but for One 5 pin 5 Amps socket point controlled by one switch on independent board complete all as specified and directed.

All as per item No 86 above but with 2.5 Sqmm copper conductor including 2.5 Sqmm copper cable as earth wire for one 6 Pin 16 Amps Socket outlet on independent board complete all as specified and directed..

All as per item No 86 above but with 4 Sqmm copper conductor including 4.0 Sqmm copper cable on earth wire for sheet metal enclosure complete all as specified and directed.

S&F modular switch 1 way 6 Amps,1 module complete all as specified and directed.

S&F Ceiling Rose, 3 phase/ PVC polycarbonate, isolated body complete all as specified and directed.

S&F Modular socket 5 Amps and 2/3 pin, 2 module complete all as specified and directed.

S&F Modular socket 6 A/16 A - 2/3 2 module complete all as specified and directed.

S&F Modular type switch 15 A pne way SP complete all as specified and directed.

Taking down existing Light fittings of any type and size and removing to store yard complete all as specified and directed..

Supply and fix LED Tubelight fitting 20 Watts DAWN PLUS, smart Extruded Aluminium LED Batten (4 ft) with higher efficiency, Microwave sensor to save more energy reduces the light by 70% during non-occupancy 100 Lumen/Watt complete all as specified and directed.Cat Part No. BCLAB 20W LED PS of Bajaj or or equivalent in list of makes.

S&F LED surface mounted square shaped luminaire with low height housing and high transmitivity diffuser 32 W, 240 volt 104 Lumen/watt all as per specified and directed. Make Philips Cat Part No. SM365C LED32-6500 PSU OD WH/ or equivalent in list of makes

S&F LED mirror light fitting 10 watt 100 Lumen/watt with connected accessories complete all as specified and directed. Make : Philips Cat Part No. BN 021 LED 10S 6500 PSU GR S1 or Make Luker Cat Part No. LMR10 or Make Crompton Cat Part No. LDL-10-CDL”

S&F LED indoor wall decorative light 14 W, 240 volt all as per specified and directed. Make Luker Cat Part No. LWL-110-2 or equivalent in list of makes

Supply and fixing building security light made up of pressure die cast housing with toughened glass and high power LEDs with option of secondary optic with IP 66 protection of 60 Watt efficiency 100 Lumen/watt including taking down of existing light fitting of any type and makecomplete all as specified and directed. Make: Crompton Cat Part No. LSTP-60-CDL-M or Make Luker Cat Part No. LST-60 / Make Havells Cat Part No. ENDURASUNDOWNSL60WLED765PASYBOTG including suitable GI bracket of 25 mm dia, and fixing arrangement on walls

S&F LED flat panel with high brightness with glare free recessed 2 feet by 2 feet 36 Watt 4000k,120 Lumen/Watt fitting including all connection all as specified and directed. Make Philips Cat Part No. RC380BLED36S-6500G4L60W60PSUOD or Crompton Cat Part No. LCTLRNE-36-FO-CDL or Make Havells Cat Part No. VENUSNEOHE4X1PLR36WLED857S”

S&F ceiling fans complete with electronic type regulator and accessories 230 V, 1200 mm sweep, BEE 5 star rated incl taking down old fan complete all as specified and directed. Make CG Cat Part No. Energion HS BLDC or Make Havells Cat Part No. Efficiencia Neo (BLDC 26 W) / Make Atomberg Cat Part No. EFFICIO” Note :- Old ceiling fans will be deposited in MES store yard.

S&F wall mounted fans AC single phase 230/240 V of size 450 mm sweep, 1200 rpm, incl taking down old fan complete all as specified and directed. Make : Havells Cat Part No. V3 or or Make Crompton Cat Part No. AC450WALL-1 / Make Usha Cat Part No. 450MM DOMINAIRE WALL FAN”. Note : Old wall mounted fans will be deposited in MES store yard.

S&F heavy duty exhaust fans AC single phase 230/240 V of size 450 mm sweep, 900 rpm, incl taking down complete all as specified and directed. Make : Havells Cat Part No. Turbo Jet SP or or Make Crompton Cat Part No. EXHD450-4-1 or Make Usha Cat Part No. 450MM S.PH TURBO HDEF 900RPM ISI GREY”. Note : Old exhaust fans will be deposited in MES store yard.

Taking down unserviceable ceiling fan of 1200mm/ 1400mm sweep, cutting out the existing burnt out fan motor winding, cleaning the motor slots, rewinding the motor with insulated copper winding wire of existing gauge, baking/ heating up the motor to achieve the proper insulation resistance and re-hanging/ refixing after repair including applying a coat of synthetic enamel paint (Glossy finish) with spray gun, marking MES No. complete all as specified.

Taking down unserviceable exhaust fan of 300mm/ 450mm sweep, cutting out the existing burnt out fan motor winding, cleaning the motor slots, rewinding the motor with insulated copper winding wire of existing gauge, baking/ heating up the motor to achieve the proper insulation resistance and re-hanging/ refixing after repair including applying a coat of synthetic enamel paint (Glossy finish) with spray gun, marking MES No. complete all as specified.

Taking down unserviceable Wall mounting fan of 450mm sweep, cutting out the existing burnt out fan motor winding, cleaning the motor slots, rewinding the motor with insulated copper winding wire of existing gauge, baking/ heating up the motor to achieve the proper insulation resistance and re-hanging/ refixing after repair including applying a coat of synthetic enamel paint (Glossy finish) with spray gun, marking MES No. complete all as specified.

S&F fan regulator electronic step type, modular type, 120 W, 2 module complete all as specified and as directed.

M&L earth continuity or main earthing lead fixed to wall on batten or recess or chases or burried in ground or drawn in conduit/ pipe or fixed to poles or any other indicated situation for loop earthing etc. as required galvanised iron strip of size 25x4 mm complete all as specified.

S&F Sheet metal enclosures with socket plug top and MCB' single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 A MCB complete all as specified and directed.

Taking down old DBs with MCCB/ MCBs of any size complete all as specified and directed.

S&F SS enclosure suitable for MCCB 160 Amp complete all as specified and as directed. Make L&T Cat Part No. CM91003OOOO or equivalent make in list of makes

S&F Sheet metal enclosure TPN for DBs when MCBs to be used 6 way with 200 amps bus bar double door IP 43 glazed door complete all as specified and as directed. Make : L&T Cat Part No. DBTPN006GD or equivalent make in list of makes

S&F Sheet metal enclosure TPN for DBs when MCBs to be used 8 way with 200 amps bus bar double door IP 43 glazed door complete all as specified and as directed. Make : L&T Cat Part No. DBTPN006GD or equivalent in list of makes

S&F SPN sheet metal enclosure for DB 8 ways Double door complete all as specified and directed.

S&F SPN sheet metal enclosure for DB 4 ways Double door complete all as specified and directed..

S&F MCCB 4 pole 415 Volt, fixed type 160 Amps with breaking capacity 16 KA complete all as specified and directed.

S&F MCB 'B' Curve 63 Amp, 4 pole, 415 Volts. Make : L&T Cat Part No. BB40630B or equivalent make in list of makes all as specified and directed.

S&F MCB 'B' Curve 6-32 Amp SPN, 240 Volts Make L&T Cat Part No. BB20320B or equivalent make in list of makes all as specified and directed.

S&F MCB 'B' Curve SP 6 to 32 Amp, 240 Volts, Make L&T Cat Part No. BB10060B to BB10320B or equivalent make in list of makes all as specified and directed.

Taking down old sub main wiring of any size complete all as specified and directed.

M/L submain wiring with 2 single core 4 Sqmm PVC insulated unsheathed multistranded copper conductor cable 1100 volt grade drawn throgh and including PVC rigid conduit concealed wiring inculding necessary PVC conduit specials including chases cutting complete exceapt beam and RCC roof and one run of 4Sqmm PVC insulated unshearthed single core 1100 volts grade multistranded copper conductor cable as earth continuity conductor and connceting with suitable size thimble complete allas specified and as directed. Note: two run of 4 sqmm size PVC cable , one run of 4 Sqmm size PVC cable as earth wire and one run of PVC conduit shall be measured as one unit length

All as per item No. 124 but 2 single core 6 Sqmm with 6 Sqmm earth wire complete all as specified and directed. Note: Note: two run of 6 sqmm size PVC cable , one run of 6 Sqmm size PVC cable as earth wire and one run of PVC conduit shall be measured as one unit length

M&L for sub main wiring with 4 runs of 16 Sqmm (HRFR) PVC insulated unsheathed multistranded copper conductor cable and 1 run of 16 Sqmm (HRFR) cable as earth continuity wire and including PVC conduit concealed in wall/ floor including cutting chases and making good disturbed surfaces to match with existing surface. Note : 4 runs of 16 Sqmm sub main wire and one run of 16 Sqmm for earthing and one run of casing capping with accessories shall be measured as one unit.

Taking down old earthing complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate elctrode 60 x 60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth strip 25 x 4 mm as earthing lead by means of bolts nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.point 3 including earthing pit PCC (1:3:6) type C1 RCC precast (1:2:4) type B1 cover slab of 100mm thick using 8mm dia TMT bars @100mm c/c as reinforcement 40mm dia GI protection pipe and 20mm dia GI pipe of medium grade for watering pipe ,wire mesh,funnel and providing charcoal or coke and salt in alternative layers connected to earthing test point all as specified or indicated including testing on completion.

Taking down old GI / CPVC pipe of size 40 mm complete all as specified and as directed.

Taking down old GI / CPVC pipe of size 25 mm complete all as specified and as directed.

Taking down old GI / CPVC pipe of size 20 mm complete all as specified and as directed.

Supply and fix on wall/concealed on wall high pressure CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings including all necessay fittings, solvents of size 40 mm dia complete all as specified and directed. Make: Supreme/Eurotech /Astral/SFMC

Supply and fix on wall/concealed on wall high pressure CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings including all necessay fittings, solvents of size 25 mm dia complete all as specified and directed. Make: Supreme/Eurotech /Astral/SFMC

Supply and fix on wall/concealed on wall high pressure CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings including all necessay fittings, solvents of size 20 mm dia complete all as specified and directed. Make: Supreme/Eurotech /Astral/SFMC

Taking down old bib tap, stop cock, shower, pillar tap, sink cock, angle valve, health faucet, self closers presmatic and angle cock etc complete all as specified and as directed.

Supply and fixing of Bib tap CP, Quarter turn with flange and areator, fancy type short body cast copper alloy with crutch or butterfly handle screwed for GI/cpvc pipe of size 15mm , complete all as specified and as directed.(Make : Model No F2004151 of Cera or equivalent in prayag/hindware)

Supply and fixing of Bib tap CP, Quarter turn with flange and areator, fancy type Long body cast copper alloy with crutch or butterfly handle screwed for GI/cpvc pipe of size 15mm , complete all as specified and as directed by the Engineer-in-charge.(Make : Model No F2004152 of Cera or equivalent in prayag/hindware)

Supply and fix of CP Bib cock short body with flange and nozzle for garden/ washing machine of size 15 mm including necessary fixing accessories with GI/ CPVC pipes complete all as specified and as directed . Make Cera Model No. 2003153 or equivalent in Prayag/ Jaguar

Supply and fixing 15mm angle valve,quater turn with flange, with flange type chromium plated for fixing with CPVC pipe complete specified and as directed..(Make : Model No: F2004201 of Cera or equivalent in prayag/ hindware)

Taking down old PVC conncetion complete all as specified and as directed.

Supply and fixing PVC connection pipe 16mm dia (outer 450mm long cold water and taking down old one complete with brass union on both sides to suit 15mm GI pipe complete all as specified and directed .

Supply and fixing in pillar taps, swan neck spout with areator, cast copper alloy with capstan heads chromium plated fancy type screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed for 15mm bore pipe,complete all as specified and directed .(Make : Cera, Model No:F2004105 or equivalent make in list of makes)

Supply and fixing in pillar taps, spout with areator, cast copper alloy with capstan heads chromium plated fancy type screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed for 15mm bore pipe,complete all as specified and directed ..(Make : Model No:F2004101 of Cera or equivalent make in prayag/hindware/Jaguar).

Supply and Fixing of Kitchen sink cock quarter turn wall mounted with long swivel spout not less than 150 mm and wall flange complete all as specified and as directed .Model No: F2004251 of CERA or equivalent make in Prayag /Jaguar/hindware.

Supply and fixing health faucet ABS body with wall hook and 1 metre SS braided rubber hose pipe , including taking out old one all as per specified and directed (Make : Model No: F8030102 of Cera or equivalent in prayag/hindware/Jaguar).

Supply and Fixing CP angle cock,Self closers Pressmatic with wall flange and 200 mm connecting pipe for urinal pots to fixed in 15/20 mm Pipe,complete all as specified (Make : Cera Model No:F 9020203 or equivalent in prayag/hindware).

M/L for cutting chasses on walls floor etc not exceeding 20 cm girth and making good the disturbed surface to match with the existing after removing the existing concealed pipe/laying new pipe, complete all as specified and directed .

Material and labour for cement concrete in foundations, filling and mass concrete type C2 1:3:6(40mm graded aggregate) complete all as specified and directed.

Taking down old rotational moulded polythene water storage tanks of capacity 2000 litres complete all as specified and as directed.

Supply and fixing of Rotational mouldede polyethylene water storage tanks (cylinderical vertical with closed top) hoisted & fixed in position of capacity 2000 liters complete all as specified and directed.Make : Sintex (ISI)/ Aquatech

Taking down old CPVC ball valve of size 20 mm / 25 mm / 40 mm complete all as specified and as directed.

S& F CPVC Ball Valve of size 40 mm dia suitable for CPVC pipe incl necessary fittings complete all specified and directed. Make: Supreme/Eurotech /Astral/SFMC

M & L for CPVC Ball Ball Valve of size 25 mm dia suitable for CPVC pipe incl necessary fittings complete all specified and directed. Make: Supreme/Eurotech /Astral/SFMC

M & L for CPVC Ball Ball Valve of size 20 mm dia suitable for CPVC pipe incl necessary fittings complete all specified and directed. Make: Supreme/Eurotech /Astral/SFMC

S/F float valve synthetic(PVC) of size 25 mm dia high pressure with polythene ball of size 6" dia and flynut complete all as specified and directed.

Taking down old float valve synthetic(PVC) of size 25 mm complete all as specified and directed.

M/s ANTONY THOMAS AND CO

MS BUILDERS

K THOMAS AND COMPANY

M/s Antony Kallarakkal