PROVISION OF INTERNAL DRAIN AT KAUTILIYA AUDITORIUM P 153 AND SANITARY ANNEXE AT OLD ZAMORIN BUILDING P 91 AT INS ZAMORIN

Amount

Dismantling floor hearth or wall tiling including cement mortar bedding having any thickness and removing / disposal of the rubbish off the premises complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings exc 15 cm thickness above ground floor complete all as specified and as directed.

Excavation in trenches n.exc 1.50m wide and n.exc 1.5m deep for foundation etc and getting out in hard/dense soil complete all as specified and as directed.

Material and labour for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

Material and labour for TMT bars 10mm dia & over cut to length bent to shape required inculding cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire annealed not less than 0.9 mm dia or securing with clipscomplete all as specified and as directed.

Material and labour for formwork to faces of walls,retaining walls, abutments, parapets and staircase railings and similar work including attached pilasters, buttresses, etc complete all as specified and as directed.

Material and labour for Design mix concrete RCC M-30 grade in walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and as directed.

Material and labour for providing of weep holes in surface drain wall with 50 mm dia UPVC pipes (SCH-40) extending through the full width of the structure with slope 1V : 20H towards drain face complete all as specified and as directed.

Material and labour for providing, laying of filter media of brick crushed aggregate satisfying the requirement laid down in Table No. 300.3 Class III of MORT&H specifications to a thickness of not less than 300 mm provided on the entire surface behind the surface drain to full height compacted to a firm condition complete all as specified and as directed.

Material and labour for rendering 10mm thick in CM (1:4) on fair faces of brickwork or concrete surfaces and rendering is to be finished even and smooth without using extra lime or cement complete all as specified and as directed.

Material and labour for PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in coping/bed block including weathering slightly rounded or chamfered angles and throating as directed and including necessary form work required complete all as specified and as directed. and as directed.

Material and labour for precast cement concrete block masonry with solid blocks type C1, 1:3:6 (20mm graded aggregate) exc 10 cm in width and set in cement mortar 1:6 complete all as specified and as directed.

Material and labour for precast RCC 1:2:4 type B1 (using 20 MM graded stone aggregate) as in cover slabs for drainage complete all as specified and as directed.

Material and labour for plain cement concrete 25 mm thick type B-1 1:2:4 (using 20mm graded aggregate) complete all as specified and as directed.

Material and labour for vitrified colourd ceramic tiles 8mm thick (square/rectangular), light shade polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set with or without spacers and jointed in neat cement slurry and pointed in white or coloured cement /epoxy to match the shade including 20mm thick screed bed in CM 1:4 complete all as specified and as directed.

Dismantling wall, ceiling boards, (fiber, pulp, insulation etc.) or insulation boards/ slabs/ any thickness including cover fillets/grid frame work complete all as specified and as directed.

Supply and fix in repair perforated aluminium board/tiles minimum thickness 2mm for insulation and accoustic purposes fixed with screws to aluminium frame work or with staples on snap grid complete all as specified and as directed.

Supply and fix aluminium tubular sections fixed on to plastered or RCC wall surfaces using SS screws. The aluminium sections should be straight in both horizontal or vertical directions even if any undulations are there on wall. Plastering or chipping of surfaces shall be done to attain the verticality and horizontality of wall lining without any extra cost to department complete all as specified and as directed.

Material and labour 25 mm 1st class hardwood planed one side boarding, supplied & fixed with screws in any situation to aluminium frame work complete all as specified and as directed.

Material and labour 35 mm 1st class hardwood wrought treads with rounded nosings with 20 mm wrought risers on tongued both edges glued wedged and blocked complete all as specified and as directed.

Complete removal of existing treatment from the surface of any description over 10cm in width or girth and applying wood filler liquid transparent and two coat of synthetic varnish complete all as specified and as directed.

Material and labour for carefully removing the existing stadium chairs fixed with nut and bolt to floor MS panel and checking chair frames and fixing any necessary components, reinstalling chairs securely to ensure durability and stability . Ensuring all chairs are properly installed and cleaned complete all as specified and as directed.

Demolition of stone slab marble of any description or thickness in floors or in any position laid, bedded and pointed in any mortar complete all as specified and as directed.

Material and labour Udaipur Green marble stone 20 mm thick machine cut, bedded jointed and pointed with white cement mixed with pigment to match the shade of stone including cutting, rubbing and polishing surface and rounding off edges match laid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

Material and labour machine cut kota stone slab flooring with 20-25mm thick over and including 20mm thick screed bed in CM 1:4 and jointed with grey cement slurry and pointed with white cement mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Taking down shutters from frames and re-fixing in same opening exc 2 sqm as required at site complete all as specified and as directed.

Material and labour for complete removal of existing surface by scrapping of walls including cornices/ pillars etc. by brooming down and applying two coats of acrylic emulsion paint interior grade over a coat of emulsion primer over a coat of wall putty of uniform finish complete all as specified and as directed.

Material and labour for preparation of old treated surfaces and applying one coat of acrylic emulsion (exterior grade) antifungal paint on wall including filling of depressions/ holes with external wall care putty and necessary scaffoldings all as specified and as directed. and as per manufacturer's instructions and complete all as specified and as directed.

Removing excavated material (soils) exc 1.50 km but n. exc 5 km and depositing where directed at a level n.exc 1.5 m above the starting point all as specified and directed by Engineer-in-Charge.

Material and labour for proper covering of all auditorium chairs using thick gauge polythene sheets, edge sealing and taping to prevent dust, debris, and moisture infiltration and regular inspection and re-adjustment of covers during the course of work as needed and complete removal and disposal of covers after the completion of all work with ensuring no residue or damage to chairs complete all as specified and as directed.

Material and labour for 100mm thick PCC type B- 2, 1:2:4 (40mm graded aggregate) as in sub base complete all as specified and as directed.

Material and labour for 100mm thick Hard core, broken stone /boulders to gauge n exc 63mm for plinth protection complete all as specified and as directed.

Material and labour for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed..

Material and labour for 75mm thick PCC type C-2, 1:3:6 ( (40mm graded aggregate) as in plinth protection complete all as specified and as directed.

Material and labour laterite block masonry set and jointed in CM 1:4 all as specified and as directed.

Material and labour reinforced concrete cement Design mix M-30 grade for foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

Material and labour reinforced concrete cement Design mix M-30 grade for columns, pillars, piers, posts and struts complete all as specified and as directed.

Material and labour reinforced concrete cement Design mix M-30 grade for Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

All as per Item No 38.00 above but in chajjas

Material and labour reinforced concrete cement Design mix M-30 grade for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

All as per Item No 05 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

Material and labour for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished flat surfaces of concrete complete all as specified and as directed.

Material and labour for formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed.

Material and labour for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed.

Material and labour for formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and as directed.

Material and labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

Material and labour mat finished coloured non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match & provided with 4mm spacer, spacer gaps to be filled with approved epoxy complete all as specified and as directed and as directed by Engineer- in- Charge, set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed..

Material and labour for glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match etc. and including 10mm thick rendering as backing coat in CM 1:3 all as specified & provided with 4mm spacer, spacer gaps to be filled with approved epoxy complete all as specified and as directed by Engineer- in- Charge.

Rendering 15mm thick on fair faces of brick work or concrete ceiling surfaces built in CM 1:6 to be finished even and smooth without using extra cement complete all as specified and as directed..

Supply only Liquid water proofing compound complete all as specified and as directed.

Rendering 5mm thick on fair faces of brick work or concrete ceiling surfaces built in CM 1:3 to be finished even and smooth without using extra cement complete all as specified and as directed..

Material and labour powder coated Anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

Material and labour for Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and as directed.

Supply and fix figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane exc 0.5 sqm in each pane complete all as specified and as directed.

Material and labour for galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

Material and labour for preparation of new surfaces and appling two coat of acrylic emulsion paint (interior grade) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification on walls and ceilings complete all as specified and as directed.

Material & Labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces including preparation of new surface ,washing, rubbing down and stopping of distempered and painted surfaces complete all as specified and as directed.

Material and labour for returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil complete all as specified and as directed.

Material and labour for removing excavated material exc. 50m & n.exc 250m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

Material and labour for concrete bed to drain pipes for 150mm bore pipe including packing under, and haunching against the sides of pipes after they are laid and tested; inand tested complete all as specified and as directed.

Supplying and laying of 20 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 and necessary fittings on walls/ceiling or laying in floors including cutting chases, chipping masonry to conceal pipes and concealing the pipeline inside wall and finishing the surface with CM 1:4 even and smooth and painting to match the adjecent laterite surfaces complete all as specified and as directed.

Supplying and laying of 25 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 and necessary fittings on walls/ceiling or laying in floors including cutting chases, chipping masonry to conceal pipes and concealing the pipeline inside wall and finishing the surface with CM 1:4 even and smooth and painting to match the adjecent laterite surfaces complete all as specified and as directed.

Supply and fix Gun-metal, globe or gate valves, with iron wheel head, screwed both ends and fixed for 25mm CPVC pipe and fixed complete all as specified and as directed.

Supply and fix Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed for 20mm CPVC pipe and fixed complete all as specified and as directed.

Supply and fix Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball for 25mm dia CPVC pipes . (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and as directed..

Supply and fix in repair vitreous china wash basin counter sunk type oval shape, star white including waste coupling chromium plated, fixing brackets, cutting for and pinning in ends of brackets complete all as specified and as directed. and as directed.

Material and labour machine cut granite stone slab 20mm thick of approved colour and shade as in steps, jambs, pillars, window- cills, cooking platforms, WHB platform and like over and including 15mm thick screed bed in CM 1:4; laid and jointed in grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the slab including grinding and polishing complete all as specified and as directed.. The rates shall be inclusive of cutting holes in any size and number, rounding edges etc whatever needed to facilitate the fixing of fittings and fixtures on Granite slab. The hole portion will not be deducted from measurement and payment.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

Supply and fix in repairs 32mm bore brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed.

Supply and fix in repairs Vitreous China wash down water closet pan (pedestal pattern), along with Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device in repairs.

Supply and fix 10 ltrs capacity PVC valveless syphonic action type flushing cistern low level with inlet ball valve, float and handle including brackets.

Supply and fix PVC connections 15mm size with PTMT nuts of length 450mm.

Supply and fix 110 mm PVC (SWR) gully trap setting and jointing with solvent cement.

Supply and fix CP grating of 110 mm da including jointing with solvent cement all as specified and as directed.

Supply and fix in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Supply and fix in repairs 15 mm fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed.

Supply and fix in repairs15 mm CP fancy Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed.

Supply and fix 15 mm dia chromium plated fancy type angular stop walve in repair.

Supply and fix in repair Tubular towel rail, Brass, 20mm dia, D type, 60cm long between flanges.

Supply and fix PVC (SWR) pipes of 110mm dia single socketed in any length with rubber ring joints fixed to walls or floors including fixing arrangements to walls, making holes on walls to take pipes through, filling the joints and matching it with adjecent surfaces with cement and paints complete all as specified and as directed.

Supply and fix PVC (SWR) pipes of 75 mm dia single socketed in any length with rubber ring joints fixed to walls or floors including fixing arrangements to walls, making holes on walls to take pipes through, filling the joints and matching it with adjecent surfaces with cement and paints complete all as specified and as directed. and as directed

Supply and fix 110 mm bore PVC SWR junction single tee with acces door complete all as specified and as directed.

Supply and fix 75 mm PVC (SWR) floor trap plain including jointing with solvent cement.

Supply and fix 110mm bore PVC SWR bend with acces door complete all as specified and as directed.

Supply and fix Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

Supply and fix solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

Supply and fix 100mm mild steel butt hinges, cold rolled medium weight.

Supply and fix 150mm Aluminum anodised barrel tower bolts of extruded section.

Supply and fix 125mm extruded aluminium anodised alloy handles fabricated type.

Supply and fix 250 mm aluminum alloy anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy.

Supply and fix ISI marked triple layer 100% food grade rotational moulded Polypropylene water storage tanks 500ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position, connecting to both inlet and outlet pipelines with necessary connections and connectors all as specified and as directed.

Supply, Install, Testing & Commissioning of 2 HP/1.5 kW dewatering pump with float switch, delivery size of 50mm, 220V complete all as specified and as directed by Engr-In-Charge. Make : Crompton, model No. STPM22(1PH)-15 or equivalent in Kirloskar/V-guard

Supply & Fix flat submersible 3 core copper conductor PVC insulated and PVC sheathed cable of size 3 core x 2.5 Sqmm complete all as specified and directed by Engineer-in-Charge Make : Havells/Polycab/Gloster or equivalent.

Supply & Fix switch socket combination modular type 16A with PVC box all as specified and directed by Engineer in charge. Make : Legrand/Anchor/Gold medal or equivalent.

Supply & Fix rigid non-metallic PVC conduit of dia 25mm exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.complete all as specified and directed. Make : Precision/Modi/Polycab or equivalent.

Supply & lay UPVC ASTM sch 80 pipe of 50mm dia including fittings complete all as specified and directed by Engr-In-Charge. Make : Ashirvad/Finolex/Supreme or equivalent.

Material & labour for chipping of wall/floor tiles for laying of pipes/conduits including making good with cement plaster complete all as specified and as directed.

Supply & fix 16 Amps 3 pin Plug top all as specified and directed by Engineer in charge.

Supply & fix PVC flexible hose pipe 50mm including clamps,connectors complete all as specified and as directed.

(a) One Light/ fan/bell point controlled by one switch.

(b) 5 Amps socket point on independent board.

Supply & fix ceiling rose 3 terminal/PVC/polycarbonate isolated body all as specified and directed by Engineer in charge .

Supply & fix modular switch one way 6 Amps 1 module all as specified and directed by Engineer in charge Make Legrand/Crabtree.

Supply & Fix modular socket 6 Amps 2/3 pin 2 module. Make Legrand /Crabtree.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specifed and directed.

Supply & Fix LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed by Engr In Charge.

Supply & fix SPN 4 way MCB DB double door 240 volts complete all as directed by Engr-In-Charge.

Supply & fix 2 Pole 25 Amps RCCBs FOR EARTH LEAKAGE PROTECTION complete all as directed by Engr-In-Charge.

Supply & fix MCB SP up to 32 A in DB as directed by Engr-In-Charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10.0 sq mm 2 core complete all as specified and as directed.

Material & Labour of earthing for poles & other machinery/equipment using 4 mm GI wire as earthing lead and MS galvanized plate of size 60 cm x 60 cm x 6 mm, as earth electrode complete all as specified and as directed.

EXCEL ENGINEERING (BID ID -3496471)