Repairing and Painting of staff quarters at Sonpur under jurisdiction SSE/Works/SEE.

(Schedule -A), Annexure "A-1" attached, except steel reinforcement. under CPWD specification.

All Items of Wrok provided in the CPWD'DSR' - 2021 with upto date corrections as per (Schedule -A),

Annexure "A-1" attached, except steel reinforcement. under CPWD specification.

S No. Item No Description of Item Unit Qty Rate Amount

2.0 EARTH WORK

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

Earth work in excavation by mechanical means

(Hydraulic excavator) / manual means in

foundation trenches or drains (not exceeding 1.5

m in width or 10 sqm on plan), including dressing

of sides and ramming of bottoms, lift upto 1.5 m,

including getting out the excavated soil and

disposal of surplus excavated soil as directed,

within a lead of 50 m.

2.27 Supplying and filling in plinth with sand under cum 10 2161.2 21612

2 floors, including watering, ramming,

consolidating and dressing complete.

Surface dressing of the ground including

removing vegetation and in-equalities not

exceeding 15 cm deep and disposal of rubbish,

lead up to 50 m and lift up to 1.5 m.

4.0 CONCRETE WORK

4.1S CEMENT CONCRETE (CAST IN SITU)

Providing and laying in position cement concrete

4.1 of specified grade excluding the cost of centering

and shuttering - All work up to plinth level :

4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) derived cum 25 7365.15 184128.75

from natural sources : 4 graded stone aggregate

20 mm nominal size derived from natural

5.0 REINFORCED CEMENT CONCRETE

5.1S CAST IN SITU

Providing and laying in position specified grade

of reinforced cement concrete, excluding the cost

of centering, shuttering, finishing and

reinforcement - All work up to plinth level :

derived from natural sources: 3 graded stone

aggregate 20 mm nominal size derived from

natural sources)

Reinforced cement concrete work in walls (any

thickness), including attached pilasters,

buttresses, plinth and string courses, fillets,

5.2 columns, pillars, piers, abutments, posts and

struts etc. above plinth level up to floor five level,

excluding cost of centering, shuttering, finishing

and reinforcement :

derived from natural sources : 3 graded stone

aggregate 20 mm nominal size derived from

natural sources)

5.9S FORM WORK

Centering and shuttering including strutting,

propping etc. and removal of form for

5.9.3 Suspended floors, roofs, landings, balconies and Sqm 25 766.55 19163.75

access platform

5.9.5 Lintels, beams, plinth beams, girders, Sqm 30 608.35 18250.5

bressumers and cantilevers

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Sqm 15 804.25 12063.75

5.12S PRE-CAST RCC

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

5.12 Providing, hoisting and fixing above plinth level cum 5 9673.5 48367.5

up to floor five level precast reinforced cement

concrete work in string courses, bands, copings,

bed plates, anchor blocks, plain window sills and

the like, including the cost of required centering,

shuttering but , excluding cost of reinforcement

with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)

derived from natural sources : 3 graded stone

aggregate 20 mm nominal size derived from

natural sources).

6.0 MASONRY WORK

Brick work with common burnt clay F.P.S. (non

6.1 modular) bricks of class designation 7.5 in

foundation and plinth in:

Brick work with common burnt clay F.P.S. (non

modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V

level in all shapes and sizes in :

6.12S HALF BRICK MASONRY

Half brick masonry with common burnt clay F.P.S.

6.12 (non modular) bricks of class designation 7.5 in

foundations and plinth in :

Half brick masonry with common burnt clay F.P.S.

(non modular) bricks of class designation 7.5 in

superstructure above plinth level up to floor V

8.0 CLADDING WORK

8.20S STONE WORK DRY CLADDING

8.31 Providing and fixing Ist quality ceramic glazed Sqm 1130 1063.45 1201698.5

wall tiles conforming to IS: 15622 (thickness to

be specified by the manufacturer), of approved

make, in all colours, shades except burgundy,

bottle green, black of any size as approved by

16 Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per

sqm, including pointing in white cement mixed

with pigment of matching shade complete.

9.0 WOOD AND P.V.C. WORK

9.1S FRAMES AND TRUSSES

Providing wood work in frames of doors,

windows, clerestory windows and other frames,

wrought framed and fixed in position with hold

fast lugs or with dash fasteners of required dia &

length (hold fast lugs or dash fastener shall be

paid for separately).

9.1.3 Kiln seasoned and chemically treated hollock cum 1.5 74199.7 111299.55

Providing and fixing panelled or panelled and

glazed shutters for doors, windows and

clerestory windows, fixing with butt hinges of

required size with necessary screws, excluding

panelling which will be paid for separately, all

complete as per direction of Engineer-in-charge.

(Note:- Butt hinges and necessary screws shall be

paid separately)

Kiln seasoned and chemically treated hollock

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

Providing and fixing panelling or panelling and

glazing in panelled or panelled and glazed

shutters for doors, windows and clerestory

9.7 windows (Area of opening for panel inserts

excluding portion inside grooves or rebates to be

measured). Panelling for panelled or panelled

and glazed shutters 25 mm to 40 mm thick :

9.7.2 Kiln seasoned and chemically treated hollock Sqm 25 2039.8 50995

9.7.3 Ply wood 5 ply, 9 mm thick

9.7.3.1 Decorative plywood both side decorative veneer Sqm 15 2366.35 35495.25

(Type - I) conforming to IS 1328 BWR type

9.7.7 Float glass panes

9.7.7.1 4 mm thick glass pane (weight not less than Sqm 10 1897.1 18971

Providing and fixing 25 mm thick shutters for cup

Providing and fixing ISI marked flush door

shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board construction

9.21 with frame of 1st class hard wood and well

matched commercial 3 ply veneering with

vertical grains or cross bands and face veneers

on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel Sqm 35 2015.75 70551.25

butt hinges with necessary screws

9.40S MISCELLANEOUS-WOOD WORK

Providing and fixing M.S. grills of required pattern

in frames of windows etc. with M.S. flats, square

or round bars etc. including priming coat with

approved steel primer all complete.

9.48.2 Fixed to openings /wooden frames with rawl Kg 350 197.7 69195

plugs screws etc.

Providing and fixing fly proof galvanized M.S.

wire gauge to windows and clerestory windows

9.51 using wire gauge with average width of aperture

1.4 mm in both directions with wire of dia 0.63

mm all complete.

9.55S BRIGHT FINISHED M.S. FITTINGS

Providing and fixing ISI marked, IS : 1341, M.S.

9.56 heavy weight bright finishied butt hinges with

necessary screws etc. complete :

COPER OXIDISED MILD STEEL FITTINGS (COPPER

OXIDISED AS PER IS: 1378)

Providing and fixing ISI marked oxidised M.S.

9.62 sliding door bolts with nuts and screws etc.

complete : (copper oxidized as per IS: 1378)

Providing and fixing ISI marked oxidised M.S.

tower bolt black finish, (Barrel type) with

necessary screws etc. complete : (copper oxized

as per IS: 1378)

Providing and fixing ISI marked oxidised M.S.

handles conforming to IS:4992 with necessary

screws etc. complete : (copper oxized as per IS:

9.105S GYPSUM BOARD PARTITIONS

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

9.119 Providing and fixing factory made P.V.C. door Metre 150 408.25 61237.5

frame of size 50x47 mm with awall thickness of 5

mm, made out of extruded 5mm rigid PVC foam

sheet, mitred at corners and joined with 2 Nos of

150 mm long brackets of 15x15 mm M.S. square

tube, the vertical door frame profiles to be

29 reinforced with 19x19 mm M.S. square tube of 19

gauge, EPDM rubber gasket weather seal to be

provided through out the frame. The door frame

to be fixed to the wall using M.S. screws of

65/100 mm size, complete as per manufacturer's

specification and direction of Engineer- in-

Providing and fixing factory made panel PVC door

shutter consisting of frame made out of M.S.

tubes of 19 gauge thickness and size of 19 mm x

19 mm for styles and 15x15 mm for top &

bottom rails. M.S. frame shall have a coat of steel

primers of approved make and manufacture.

M.S. frame covered with 5 mm thick heat

moulded PVC 'C' channel of size 30 mm

thickness, 70 mm width out of which 50 mm shall

be flat and 20 mm shall be tapered in 45 degree

angle on both side forming styles and 5 mm

thick, 95 mm wide PVC sheet out of which 75mm

shall be flat and 20 mm shall be tapered in 45

degree on the inner side to form top and bottom

rail and 115 mm wide PVC sheet out of which 75

9.120 mm shall be flat and 20 mm shall be tapered on

both sides to form lock rail. Top, bottom and lock

rails shall be provided both side of the panel. 10

mm (5 mm x 2 ) thick, 20 mm wide cross PVC

sheet be provided as gap insert for top rail &

bottom rail, paneling of 5 mm thick both side PVC

sheet to be fitted in the M.S. frame welded/

sealed to the styles & rails with 7 mm (5 mm+2

mm) thick x 15 mm wide PVC sheet beading on

inner side, and joined together with solvent

cement adhesive. An additional 5 mm thick PVC

strip of 20 mm width is to be stuck on the interior

side of the 'C' Channel using PVC solvent

adhesive etc. complete as per direction of

Engineer-in-charge, manufacturer's specification

10.0 STEEL WORK

10.2 Structural steel work riveted, bolted or welded in Kg 1195 111.95 133780.25

built up sections, trusses and framed work,

31 including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer

10.4 Providing and fixing 1 mm thick M.S. sheet Sqm 12 5374.35 64492.2

sliding-shutters, with frame and diagonal braces

of 40x40x6 mm angle iron, 3 mm M.S. gusset

32 plates at the junctions and corners, 25 mm dia

pulley, 40x40x6 mm angle and T- iron guide at

the top and bottom respectively, including

applying a priming coat of approved steel primer

Steel work in built up tubular (round, square or

rectangular hollow tubes etc.) trusses etc.,

including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer,

including welding and bolted with special shaped

washers etc. complete.

11.0 FLOORING

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

11.2 Dry brick on edge flooring in required pattern Sqm 50 733.3 36665

with bricks of class designation 7.5 on a bed of

34 12 mm mud mortar, including filling joints with

local sand, with common burnt clay non modular

Cement concrete flooring 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate) finished

11.3 with a floating coat of neat cement, including

cement slurry, but excluding the cost of nosing of

steps etc. complete.

11.3.1 40 mm thick with 20 mm nominal size stone Sqm 750 545 408750

11.37S CERAMIC GLAZED TILES

11.37 Providing and laying Ceramic glazed floor tiles of Sqm 200 935.6 187120

size 300x300 mm (thickness to be specified by

the manufacturer) of 1st quality conforming to IS

: 15622 of approved make in colours such as

White, Ivory, Grey, Fume Red Brown, laid on 20

mm thick cement mortar 1:4 (1 Cement : 4

Coarse sand), Jointing with grey cement slurry @

3.3 kg/sqm including pointing the joints with

white cement and matching pigment etc.,

11.41S VITRIFIED FLOOR TILES

Providing and laying Polished Granite stone

flooring in required design and patterns, in linear

as well as curvilinear portions of the building all

complete as per the architectural drawings with

18 mm thick stone slab over 20 mm (average)

thick base of cement mortar 1:4 (1 cement : 4

coarse sand) laid and jointed with cement slurry

and pointing with white cement slurry admixed

with pigment of matching shade including

rubbing , curing and polishing etc. all complete

as specified and as directed by the Engineer-in-

11.56.1 Polished Granite stone slab colour of Black, Sqm 40 3908.8 156352

Cherry/Ruby Red or equivalent

12.0 ROOFING

Providing, fixing and embedding sand cast iron

accessories for rain water pipes in the masonry

12.40 surrounded with 12 mm thick cement mortar of

the same mix, as that of masonry (lead caulking

will be paid for separately):

Providing and fixing on wall face unplasticised

Rigid PVC rain water pipes conforming to IS :

12.41 13592 Type A, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for

thermal expansion, (i) Single socketed pipes.

Providing and fixing on wall face unplasticised -

PVC moulded fittings/ accessories for

unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS : 5382,

leaving 10 mm gap for thermal expansion.

12.42.5 Bend 87.5 degrees

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

Providing and fixing false ceiling at all height

including providing and fixing of frame work

made of special sections, power pressed from

M.S. sheets and galvanized with zinc coating of

120 gms/sqm (both side inclusive) as per IS : 277

and consisting of angle cleats of size 25 mm wide

x 1.6 mm thick with flanges of 27 mm and

37mm, at 1200 mm centre to centre, one flange

fixed to the ceiling with dash fastener 12.5 mm

dia x 50mm long with 6mm dia bolts, other

flange of cleat fixed to the angle hangers of

25x10x0.50 mm of required length with nuts &

bolts of required size and other end of angle

hanger fixed with intermediate G.I. channels

45x15x0.9 mm running at the spacing of 1200

mm centre to centre, to which the ceiling section

0.5 mm thick bottom wedge of 80 mm with

tapered flanges of 26 mm each having lips of

10.5 mm, at 450 mm centre to centre, shall be

fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made

out of 2.64 mm dia x 230 mm long G.I. wire at

every junction, including fixing perimeter

channels 0.5 mm thick 27 mm high having

flanges of 20 mm and 30 mm long, the perimeter

of ceiling fixed to wall/partition with the help of

rawl plugs at 450 mm centre, with 25mm long

dry wall screws @ 230 mm interval, including

fixing of gypsum board to ceiling section and

perimeter channel with the help of dry wall

screws of size 3.5 x 25 mm at 230 mm c/c,

including jointing and finishing to a flush finish of

tapered and square edges of the board with

recommended jointing compound , jointing tapes

, finishing with jointing compound in 3 layers

covering upto 150 mm on both sides of joint and

two coats of primer suitable for board, all as per

manufacturer's specification and also including

the cost of making openings for light fittings,

grills, diffusers, cutouts made with frame of

perimeter channels suitably fixed, all complete

as per drawings, specification and direction of

the Engineer in Charge but excluding the cost of

painting with :

12.45.3 12.5 mm thick tapered edge gypsum moisture Sqm 100 1300.5 130050

resistant board

12.50 Providing and fixing precoated galvanised iron Sqm 10 671.55 6715.5

profile sheets (size, shape and pitch of

corrugation as approved by Engineer-in-charge)

0.50 mm (+ 0.05 %) total coated thickness with

zinc coating 120 grams per sqm as per IS: 277, in

240 mpa steel grade, 5-7 microns epoxy primer

on both side of the sheet and polyester top coat

15-18 microns. Sheet should have protective

guard film of 25 microns minimum to avoid

scratches during transportation and should be

supplied in single length upto 12 metre or as

desired by Engineer-in-charge. The sheet shall be

fixed using self drilling /self tapping screws of

size (5.5x 55 mm) with EPDM seal, complete upto

any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters

and trusses and including cutting to size and

shape wherever required.

13.0 FINISHING

13.4S CEMENT PLASTER (IN COARSE SAND)

13.4 12 mm cement plaster of mix :

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

CEMENT PLASTER WITH A FLOATING COAT OF

15 mm cement plaster on rough side of single or

13.8 half brick wall finished with a floating coat of

neat cement of mix :

13.16S 6MM CEMENT PLASTER

Distempering with oil bound washable distemper

13.41 of approved brand and manufacture to give an

13.41.1 New work (two or more coats) over and including Sqm 550 162.55 89402.5

water thinnable priming coat with cement primer

13.44S EXTERIOR FINISHING

Finishing walls with water proofing cement paint

of required shade :

13.44.1 New work (Two or more coats applied @ 3.84 Sqm 450 97.6 43920

Finishing with Deluxe Multi surface paint system

13.48 for interiors and exteriors using Primer as per

manufacturers specifications :

13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 Sqm 50 158.95 7947.5

48 sqm over and including one coat of Special

primer applied @ 0.75 ltr /10 sqm

Painting with synthetic enamel paint of approved

brand and manufacture to give an even shade :

Lettering with black Japan paint of approved letter

brand and manufacture per cm

13.80 Providing and applying white cement based putty Sqm 550 123.85 68117.5

of average thickness 1 mm, of approved brand

51 and manufacturer, over the plastered wall

surface to prepare the surface even and smooth

Applying priming coats with primer of approved

13.85 brand and manufacture, having low VOC (Volatile

Organic Compound ) content.

13.88 Removing white or colour wash by scrapping and Sqm 2000 16.35 32700

sand papering and preparing the surface smooth

including necessary repairs to scratches etc.

Distempering with 1st quality acrylic distember

(Ready mix) having VOC content less than 50

grams/ litre of approved brand and manufacture

to give an even shade :

Painting with synthetic enamel paint of approved

13.99 brand and manufacture of required colour to give

an even shade :

Finishing walls with water proofing cement paint

of required shade :

14.0 REPAIRS TO BUILDING

Repairs to plaster of thickness 12 mm to 20 mm

in patches of area 2.5 sq.meters and under,

including cutting the patch in proper shape,

14.1 raking out joints and preparing and plastering the

surface of the walls complete, including disposal

of rubbish to the dumping ground, all complete

as per direction of Engineer-in-Charge.

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

14.1.2 With cement mortar 1:4 (1cement: 4 coarse Sqm 150 478 71700

Fixing chowkhats in existing opening including

embedding chowkhats in floors or walls cutting

masonry for holdfasts, embedding hold fasts in

cement concrete blocks of size 15 x 10 x 10 cm

with cement concrete 1:3:6 (1 cement : 3 coarse

sand : 6 graded stone aggregate 20 mm nominal

size), painting two coats of approved wood

preservative to sides of chowkhats and making

good the damages to walls and floors as required

complete, including disposal of rubbish to the

dumping ground, all complete as per direction of

Engineer-in-Charge.

Renewing glass panes, with putty and nails

14.5 wherever necessary including racking out the old

14.5.1 Float glass panes of nominal thickness 4 mm Sqm 15 941.95 14129.25

(weight not less than 10kg/sqm)

Renewing wooden beams in roofs including

making good the holes in walls and painting with

oil type wood preservative of approved brand

and manufacture complete, including removal of

rubbish to the dumping ground, all complete as

per direction of Engineer-in-Charge.

14.17 Raking out joints in lime or cement mortar and Sqm 50 59.75 2987.5

preparing the surface for re-pointing or

60 replastering, including disposal of rubbish to the

dumping ground, all complete as per direction of

Engineer-in-Charge.

15.0 DISMANTLING AND DEMOLISHING

Demolishing cement concrete manually/ by

mechanical means including disposal of material

within 50 metres lead as per direction of

Engineer - in - charge.

15.2.1 Nominal concrete 1:3:6 or richer mix (i/c cum 12 2007.1 24085.2

equivalent design mix)

15.3 Demolishing R.C.C. work manually/ by cum 1.2 2928.1 3513.72

mechanical means including stacking of steel

62 bars and disposal of unserviceable material

within 50 metres lead as per direction of

Engineer - in- charge.

Demolishing brick work manually/ by mechanical

means including stacking of serviceable material

15.7 and disposal of unserviceable material within 50

metres lead as per direction of Engineer-in-

Taking out doors, windows and clerestory window

15.13 shutters (steel or wood) including stacking within

50 metres lead :

15.19 Dismantling steel work manually/ by mechanical Kg 150 3.2 480

means in built up sections without dismembering

and stacking within 50 metres lead as per

direction of Engineer-in-charge.

Dismantling tile work in floors and roofs laid in

15.23 cement mortar including stacking material within

50 metres lead.

Dismantling roofing including ridges, hips, valleys

15.28 and gutters etc., and stacking the material within

50 metres lead of:

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

Dismantling G.I. pipes (external work) including

excavation and refilling trenches after taking out

15.44 the pipes, manually/ by mechanical means

including stacking of pipes within 50 metres lead

as per direction of Engineer-in-charge :

16.0 ROAD WORK

16.42S CONCRETE PAVEMENTS

16.42 Cement concrete 1:2:4 (1 cement : 2 coarse sand cum 25 7399.2 184980

: 4 graded stone aggregate 40 mm nominal size)

69 in pavements, laid to required slope and camber

in panels as required including consolidation

finishing and tamping complete.

17.0 SANITARY INSTALLATIONS

Providing and fixing water closet squatting pan

(Indian type W.C. pan ) with 100 mm sand cast

Iron P or S trap, 10 litre low level white P.V.C.

flushing cistern, including flush pipe, with

manually controlled device (handle lever)

conforming to IS : 7231, with all fittings and

fixtures complete, including cutting and making

good the walls and floors wherever required:

17.1.1 White Vitreous china Orissa pattern W.C. pan of Each 20 5781.35 115627

size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china

pedestal type water closet (European type W.C.

pan) with seat and lid, 10 litre low level white

P.V.C. flushing cistern, including flush pipe, with

manually controlled device (handle lever),

conforming to IS : 7231, with all fittings and

fixtures complete, including cutting and making

good the walls and floors wherever required :

17.2.1 W.C. pan with ISI marked white solid plastic seat Each 10 5540.55 55405.5

Providing and fixing wash basin with C.I.

brackets, 15 mm C.P. brass pillar taps, 32 mm

17.7 C.P. brass waste of standard pattern, including

painting of fittings and brackets, cutting and

making good the walls wherever require:

17.7.4 White Vitreous China Flat back wash basin size Each 20 1679.6 33592

72 550x 400 mm with single 15 mm C.P. brass pillar

Providing and fixing Stainless Steel A ISI 304

(18/8) kitchen sink as per IS:13983 with C.I.

brackets and stainless steel plug 40 mm,

including painting of fittings and brackets,

cutting and making good the walls wherever

17.10.2 Kitchen sink without drain board

Providing and fixing white vitreous china water

closet squatting pan (Indian type) :

Providing and fixing P.V.C. low level flushing

cistern with manually controlled device (handle

lever) conforming to IS : 7231, with all fittings

and fixtures complete.

Providing and fixing P.V.C. waste pipe for sink or

17.28 wash basin including P.V.C. waste fittings

17.28.2 Flexible pipe

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

17.31 Providing and fixing 600x450 mm beveled edge Each 25 1411.15 35278.75

mirror of superior glass (of approved quality)

78 complete with 6 mm thick hard board ground

fixed to wooden cleats with C.P. brass screws and

washers complete.

18.0 WATER SUPPLY

18.7S C.P.V.C. PIPES

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal stability

for hot & cold water supply, including all CPVC

plain & brass threaded fittings, including fixing

18.7 the pipe with clamps at 1.00 m spacing. This

includes jointing of pipes & fittings with one step

CPVC solvent cement and testing of joints

complete as per direction of Engineer in Charge.-

Internal work - Exposed on wall

Providing and fixing Chlorinated Polyvinyl

Chloride (CPVC) pipes, having thermal stability

for hot & cold water supply, including all CPVC

plain & brass threaded fittings, i/c fixing the pipe

with clamps at 1.00 m spacing. This includes

18.8 jointing of pipes & fittings with one step CPVC

solvent cement and the cost of cutting chases

and making good the same including testing of

joints complete as per direction of Engineer in

Charge, Concealed work, including cutting

chases and making good the wall etc.

Providing and fixing G.I. pipes complete with G.I.

18.10 fittings and clamps, i/c cutting and making good

the walls etc.-Internal work - Exposed on wall

18.15S BRASS FITTINGS

Providing and fixing ball valve (brass) of

18.18 approved quality, High or low pressure, with

plastic floats complete :

Providing and fixing uplasticised PVC connection

pipe with brass unions :

18.21.2 45 cm length

Providing and fixing C.P. brass shower rose with

15 or 20 mm inlet :

18.31S C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES

18.48 Providing and placing on terrace (at all floor Litre 10000 9.7 97000

levels) polyethylene water storage tank, IS :

12701 marked, with cover and suitable locking

arrangement and making necessary holes for

inlet, outlet and overflow pipes but without

fittings and the base support for tank.

18.49S C.P. BRASS FITTINGS

Providing and fixing C.P. brass bib cock of

approved quality conforming to IS:8931 :

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

Providing and fixing C.P. brass stop cock

18.52 (concealed) of standard design and of approved

make conforming to IS:8931.

Providing and fixing C.P. brass angle valve for

18.53 basin mixer and geyser points of approved

quality conforming to IS:8931

18.54S PTMT FITTINGS

Providing and fixing PTMT bib cock of approved

quality and colour.

18.54.3 15 mm nominal bore, 165 mm long, weighing not Each 100 156.65 15665

less than 110 gms

Providing and fixing PTMT stop cock of approved

quality and colour.

18.55.3 Concealed stop cock, 15 mm nominal bore, 108 Each 10 183.4 1834

mm long, weighing not less than 108 gms

21.0 ALUMINIUM WORK

Providing and fixing aluminium work for doors,

windows, ventilators and partitions with extruded

built up standard tubular sections/ appropriate Z

sections and other sections of approved make

conforming to IS: 733 and IS: 1285, fixing with

dash fasteners of required dia and size, including

necessary filling up the gaps at junctions, i.e. at

top, bottom and sides with required EPDM

21.1 rubber/ neoprene gasket etc. Aluminium sections

shall be smooth, rust free, straight, mitred and

jointed mechanically wherever required including

cleat angle, Aluminium snap beading for glazing /

paneling, C.P. brass / stainless steel screws, all

complete as per architectural drawings and the

directions of Engineer-in-charge. (Glazing,

paneling and dash fasteners to be paid for

21.1.1 For fixed portion

21.1.1.2 Powder coated aluminium (minimum thickness of Kg 57.6 466.3 26858.88

powder coating 50 micron)

For shutters of doors, windows & ventilators

including providing and fixing hinges/ pivots and

making provision for fixing of fittings wherever

required including the cost of EPDM rubber /

neoprene gasket required (Fittings shall be paid

for separately)

21.1.2.2 Powder coated aluminium (minimum thickness of Kg 30 564.8 16944

powder coating 50 micron)

Schedule Schedule A 3-Items of steel reinforcement under DSR-2021

Item- 01 Items of steel reinforcement under DSR-2021

S No. Item No Description of Item Unit Qty Rate Amount

5.0 REINFORCED CEMENT CONCRETE

5.22S STEEL REINFORCEMENT

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in

position and binding all complete upto plinth

5.22.6 Thermo-Mechanically Treated bars of grade Fe- Kg 800 89.65 71720

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in

position and binding all complete above plinth

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

5.22A.6 Thermo-Mechanically Treated bars of grade Fe- Kg 1200 89.65 107580