REPAIR TO ROOFING, FALSE CEILING AND OH TANK IN CERTAIN BLDG AT LAMA CAMP UNDER GE MISAMARI

Amount

Dismantling AC Corrugated/ Semi corrugated Sheets as in Roofing including Ridge or Similar Pattern Roof Coverings, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness including Nainital or similar Roof Coverings, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards /Blankets/Slabs, any description and any thickness including Cover Fillets, Cornices, etc., complete all as specified and as directed.

Dismantling Boarding of any description and any position, fixed with Nails, complete all as specified and as directed.

Dismantling Timber Scantling 40 Sq Cm and over in Section in any position in Unframed Work, complete all as specified and as directed.

Dismantling Timber Fillet, Rails, Posts, Rafter, Purlins, etc. under 40 Sq Cm in Section in Unframed Work, complete all as specified and as directed.

Dismantling Wrought Iron or Mild Steel Work of any description not otherwise provided, complete all as specified and as directed.

Demolition Brick Work or Stone/ Bolder masonary built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any description, complete all as specified and as directed. Note:Demolished material to be used for filling under floors to bring upto required level.

Demolition of reed, lathing, single or double, including battens and plaster or chiken wire lathing, complete all as specified and as directed.

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level), complete all as specified and as directed. (Note:Demolished material to be used for filling under floors to bring upto required level, if neccesary)

Taking down Cement Plaster of any description on Brick Walls, Concrete Surfaces including racking out joints, hacking for key, scrubbing down with Water remove Dust, debries/ rubbish etc., complete all as specified and as directed.

Taking down Chowkat or Frame with shutter (without taking off Shutter from the Frame) not exc. 1.50 Square Metre Each,,complete all as specified and as directed.

Taking down Chowkat or Frame with shutter (without taking off Shutter from the Frame) exc. 1.50 Square Metre but not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Taking down Shutter of any description, not exc 1.00 Sqm Each, complete all as specified and as directed.

Taking down Shutter of any description, exc. 1.00 Sqm but not exc 2.00 Sqm Each, complete all as specified and as directed.

Taking up or down Steel Tubing 15mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Taking up or down Steel Tubing 20mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Stone Slabs and tiles of any description or thickness in Floors, Aprons, etc., laid dry or laid dry and pointed, complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing), removing from the Sites and rubbish off the Premises, complete all as specified and as directed.

M&L Second Class Hardwood Boarding 25mm thick, planed one side with butt joints, and fixed with nails as in Eave boards,complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding, fixed with self tapping screws as specified, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and as directed.

S&F 6mm thick asbestos cement,corrugated sheet in roofs fixed with L-typeor J-type hook bolt, complete all as specified and as directed.

S&F in repair asbestos cement one piece plain anglur ridge 6mm thick fixed with L-typeor J-type hook bolt, complete all as specified and as directed.

S & F 0.63 mm thick Plain galvanised,mild steel sheeting in ridges, hips, valley gutter all as specified with grade of zinc coating 275, complete all as specified and as directed.

S & F glavnised corrugated mild steel seathing 0.63 mm thick with two corrugation side lab fixed with coatch screw and washer in roof, wall etc with grade of zinc coating 275., complete all as specified and as directed.

S & F false ceiling with 4mm thick desingner 'E' Board of Everest Ltd or Charminar as approved by GE fixed with GI powder coated inverted Tee or 'L' section (Concealed GI frame work) of cicago metallic or Equivalent as approved by GE suspended from ceiling with FI 25x5 mm thick or butterfly hold down clips with necessary hold fastners / self tapping screws as per manufacturer instruction complete all as directed and specified incl (a) Main runner of size 28x24x0.8mm (b) Cross tee size 28x24x0.8mm (c) Wall angle 22x22x0.65mm (d) Butter fly clip / hold down clip (f) Size of grid 605x605mm (g) Two coats oil bound distemper one side of board (h) Powder coating on exposed side of tee/angle ,complete all as specified and as directed.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top:- (i) Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 for laying as in roof slab with mixing of WPC and surface finished fare and smooth without using extra cement. (ii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25ltr /Sqm conforming to IS:3384-1986. (iii) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be less applied over bituminous primer as specified above over a Application of polymeric membrance shall by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (iv) Applying two coat of aluminum paint over the APP modified membrance @ 0.11Kg/sqm. (v) taking down existing worn out PCC roof paddy not exc 0.5 mm thick and bituminous felt.

S&F in repair Ball Valve 20mm dia (minimum Weight 20mm-210 Gram), high pressure of PTMT with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and fixed, complete all as specified and as directed.

M&L preparing old treated/decorated Steel and Iron surfaces of any description, not otherwise described, over 10 Cm Width or Girth and applying One Coat of Synthetic Enamel Paint (1st Grade Quality), complete all as specified and as directed.

M&L Brick Work with Sub-Class ‘B’ Bricks (with Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L brick work with sub-class ‘B’ Bricks Straight or Curved on Plan exc.any radius in half brick thick built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:6 on Brick Walls or on Concrete Surfaces, plastered surfaces finished Even and Smooth, complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 on Brick Walls or on Concrete Surfaces, plastered surfaces finished Even and Smooth, complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 on fair faces of Brick Walls or on Concrete Surfaces, plastered surfaces finished Even and Smooth on one side of lathing, complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:6 on fair faces of Brick Walls or on Concrete Surfaces, plastered surfaces finished Even and Smooth on other side of lathing, complete all as specified and as directed.

M&L preparing new of Walls and applying Two Coats of Cement Base Paint over a coat of cement primer, complete all as specified and as directed.

M&L preparing new Plastered Surfaces of Walls and applying Two Coats of distemper oil emulsion over a coat of primer complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 ( Using 20mm graded agg) as in plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, mud stops, kneelers, apex stones, bed plates concrete complete all as specified and directed.

M&L 100mm thick Cement Concrete 1:4:8, type B2 (40mm graded aggregate), as in Sub-base finishing Concrete Surfaces Even and rough, complete all as specified and as directed.

M&L 25mm thick Cement Concrete 1:2:4, type B1 (20 mm graded aggregate), as in Sub-base finishing Concrete Surfaces Even and rough, complete all as specified and as directed.

M&L Cement Concrete 1:3:6, C2 (40mm graded aggregate), 75mm thick as in Plinth Protection, etc.,finishing Concrete Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L 50mm thick Cement Concrete 1:2:4, type B1 (20mm graded aggregate), as in path or hard standing including finishing the surface by brooming, complete all as specified and as directed.

Forming contaction (Dummy) Joints, 65mm deep and 10mm wide filled with sealing compound grade 'A', complete all as specified and as directed.

M&L for Machine pressed Precast concrete interlocking paver block any shape and size confirming to IS15658-2006 of 60mm thickness M-35 Grade over and including 50 mm thick sand screed bed/cushioning etc. complete all as spd and directed.

M & L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors incl 15mm thick screed bed in CM 1:6 and jointed in neat cement slurry and pointed in gray or colored cement to match the surface of tiles, complete all as specified and directed.

M&L for granite (of any type) tiles 20mm thick mechine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing laid our 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

Rounded to edges of stone slab one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

M & L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over cement screed base 15mm th in CM (1:4) including 40mm wide marble border, complete all as specified and as directed.

M&L Vtirified Ceramic Tiles 10mm thick (Square/ Rectangular) Dark shade polished, area of each Tile not exc. 0.36 Sqm, in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Tiles over and including 15 mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tiles, complete all as specified and as directed

M&L Non skid ceramic coloured jointless tiles 7 to 8mm thick (Square/ Rectangular) area of each tiles exceeding 0.11 Sqm but n.exc. 0.18 Sqm in floors etc. over and including 15 mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tiles complete all as specified and as directed.

M&L Non skid ceramic coloured jointless tiles 7 to 8mm thick (Square/ Rectangular) area of each tiles exceeding 0.06 Sqm but n.exc. 0.11 Sqm in floors etc. over and including 15 mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tiles complete all as specified and as directed.

M&L glazed ceramic coloured tiles, glossy finished of size 350x450x7mm/ 350x250x7mm thick as in vertical surfaces such as skirting/dados and riser of stems., over and including including 10 mm thick rendering/backing coat in CM 1:4 and set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tiles,complete all as specified and as directed.

M&L Coloured Glazed Ceramic Tiles 300x200x7mm thick in Vertical Surface i.e. dado, skirting,etc. including 10 mm thick in rendering CM 1:4 and Set and Jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the Tiles,complete all as specified and as directed.

Roughing surfaces of old concrete floor by pickinhg,sweeping clean and washing down with water remove dust etc.,complete all as specified and as directed.

S & F in repair 25mm dia, MS curtain rod of PVC coated including brackets end stop as requried for door/window for each, complete all as specified and as directed.

M&L for filling of joints for tiles/WC & WHB corner with white cement area n exc 2 sqm each complete all as specified and as directed.

M&L Second Class Hardwood in Scantlings Wrought clean sown, Timber Framed and fixed with nail, complete all as specified and as directed.

M&L Second Class Hardwood Plain Fillets sqaure, rectangular or triangular in Section Clean sawn, secured with Nails, sectional area exc. 13 Sq Cm but not exc.25 SqCm , complete all as specified and as directed.

M&L Second Class Hardwood Plain, Solid, Straight Chowkats and Frames, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue, Pinned at Joints, complete all as specified and as directed.

Refixing of shutter of any description exc 1.00 sqm but n.exc 2.00 sqm each in size at same opening complete all as directed.

Refixing door shutter of any description n.exc. 1.00 square meter each in size at same, complete as all specified and as directed.

M&L Factory Made Second Class Hardwood 30mm thick Glazed and Skelton Shutters, open rebated and prepared to receive Glass, Gauze, etc. (without Sash Bars) edges of Framing plain, chamfered or rounded, mitred beads for screwing Glass, Gauge, etc. sizes of members of Shutter as speci fied in MES Schedule Part-I Section 8, Clause No. 8.24(a) and fitted to Wooden Chowkat, complete all as specified and as directed.

M&L Factory Made Second Class Hardwood 30mm thick Glazed and Skelton window/ventilator Shutters, open rebated and prepared to receive Glass, Gauze, etc. (without Sash Bars) edges of Framing plain, chamfered or rounded, mitred beads for screwing Glass, Gauge, etc. sizes of members of Shutter as speci fied in MES Schedule Part-I Section 8, Clause No. 8.24(a) and fitted to Wooden Chowkat, complete all as specified and as directed.

M&L Flush Door Shutter 30mm thick, solid core construction with block board core and plywood face Panels commercial type on both side with particle board and fitted to Wooden Chowkat, complete all as specified and as directed.

S&f second class hardwood,30mm thick Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and as directed.

S&F aluminium anodised frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

S&F Anodised aluminium door shutters (Single/double shutter), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing anodised aluminum snap beading handles in each door, hinges, handles, anodised snap beading screws, hold fast complete all as specified and as directed and as shown on drawings. NOTE:- (i) Fixing of shutter with fitting shall be as per manufacturers instruction (ii) Rate quoted is deemed to be inclusive of aluminum hardwares as indicated, glazing clips, rubber packing, anodized aluminum snap on beading for fixing glass panes in frame , handles,Locking Arrangement but Glass panes in frame shall be measured and paid separately under respective Sch A items separately at Supply only rates)

S & F Anodised aluminium window and ventilator shutters,, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, handles, screws etc. complete all as specified and as directed. NOTE:- (i) Fixing of shutter with fitting shall be as per manufacturers instruction (ii) Rate quoted is deemed to be inclusive of aluminum hardwires as indicated, glazing clips, rubber packing, anodized aluminum snap on beading for fixing glass panes in frame, handles, Locking Arrangement but Glass panes in frame shall be measured and paid separately under respective Sch A items separately at Supply only rates)

Supply only Sheet Glass, frosted, 4.0mm thick, Glazing in Wooden/Metal Frames and glazed with Beads or Oil Putty, area exc. 0.50 SQM in Each Pane, complete all as specified and as directed.

Repairs to Aluminium doors exc 1.50 Sqm but n exc 5.00 Sqm by necessary joining cleat, glazing clips, rubber neoprene packing handles 2 Nos in each doors, hinges anodised aluminium snap beading scrw etc and refix in the same opening after complete repair except glass, complete as all specified and as directed.

Repairs to Aluminium doors n exc 1.50 Sqm by necessary joining cleat, glazing clips, rubber neoprene packing handles 2 Nos in each doors, hinges anodised aluminium snap beading scrw etc and refix in the same opening after complete repair except glass, complete as all specified and as directed.

M&L for easing of door / window shutter n.exc 1.00 sq m in size without taking down and making operation in all respects complete all as directed.

M&L for easing of door / window shutter exc 1.00 and n.exc 2.00 sq m in size without taking down and making operation in all respects complete all as directed.

S&F Factory made Solid PVC Door Frame of size 50x47 mm made out of 5.0 mm thick wood grain printed PVC sheet and edge will be painted to match with printed sheet as per specification and drawing, complete all as specified and as directed.

S&F Factory made Solid Panel PVC Door Shutter 30mm thick (Style) consisting of Frame made out of Mild Steel Square Tube for Top and Bottom Rails, mild steel Frame shall be covered with heat moulded plain colour PVC 'C' Channel having PVC Sheet Strip 20 mm wide stuck inside with Solvent Cement for Styles and plain colour PVC Sheet for Top Rail, Lock Rail & Bottom Rail on either side and as gap insert for Top Rail, Bottom Rail Panelling of plain colour PVC Sheet to be fitted in mild steel Frame welded/sealed to the Styles and Rails with suitable Sheet Beading and jointed together with Solvent Cement and fixing in the Frame at Site as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

S&F Mild Steel Butt Hinge of size 100mm, medium weight, cold rolled and fixed, complete all as specified and as directed

All as per Item no.77 here in before but for 75 mm, complete all as specified and directed.

S&F in repair Mild Steel Butt Hinge of size 100mm, medium weight, cold rolled and fixed, complete all as specified and as directed

S&F Mild Steel Sliding Door Bolt 250mm long, Plate type, Black Japanned Finish with bright Bolt not less than 12mm dia, minimum 6 Bolts and Nuts 4 on Bolt Plate 2 on Staple Plate and fixed, complete all as specified and as directed.

S&F Mild Steel Barrel Tower Bolt 150mm long, Stove Enamelled Black with bright Bolt and fixed, complete all as specified and as directed.

All as per Item no.81 here in before but for 100 mm, complete all as specified and directed.

S&F in repair Mild Steel Barrel Tower Bolt 200mm long, Stove Enamelled Black with bright Bolt and fixed, complete all as specified and as directed.

S&F Aluminium Handle 150mm long Cast type, complete all as specified and as directed.

All as per Item no.84 here in before but for 100 mm, complete all as specified and directed.

Supply and fix in repair cast iron body door closer hydrauliclly regulated, designation No. 2, universal type, suitable for door shutters of 700mm in width and weight more than 35 and fixed complete all as specified and as directed.

Supply and fix Brass Mortice lock of size 65mm, 4-Lever, complete all as specified and as directed

M&L Welding in repair exc 2.5cm but n.exc 5cm in length ( exc 20mm but n.exc 25mm in length), complete all as specified and as directed.

S&F in repair Ordinary Rat Tail 300mm, Rod Pattern Springs including Roller and Roller Plate and fixed, complete all as specified and as directed.

S&F Steel Window with side Hung Shutters including Hinges with Steel Handle and Steel Peg Stay, complete with Glazing Bars, dovetailed or welded, complete all as specified and as directed.

S&F Steel Window with side Hung Shutters including Hinges with Steel Handle and Steel Peg Stay, complete without Glazing Bars, dovetailed or welded, complete all as specified and as directed.

S&F in repair 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor complete all as specified and as directed.

S&F in repair 18mm thick prelaminated colour PVC sheet for cup board incl frame & fixed at site including PVC beading half round decorative type including hasps, stapples, continuous piano hinges, cup board knobs etc all as required, complete all as specified and as directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised., width of flaps when open in 30mm, complete all as specified and as directed. .

S&F magnetic PVC catcher for kitchen cup board complete all as specified and as directed.

S& F 25mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished, complete all as specified and as directed.

S&F in repair of external teak wood lipping 6 mm thick suitable for existing doors and block board or veenered particle board including priming, complete all as specified and as directed. .

M&L preparing new or previously untreated Wooden Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Pink Primer, complete all as specified and as directed.

S&F in repairs solid rubber beading (door seal) of 30 to 50 mm wide and 3 to 5 mm thick at bottom of existing doors, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples and fixed, complete all as specified and as directed.

S&F in repair Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples and fixed, complete all as specified and as directed.

Hacking out old/broken Glass (any thickness, size, quality or description) from Wooden Frames/metal frame, Glazed with Putty or fixed with Beads, complete all as specified and as directed.

M&L Sheet Glass, Ordinary, 3.0mm thick, Glazing in Wooden/Metal Frames and glazed with Beads or Oil Putty, area not exc. 0.50 SQM in Each Pane, complete all as specified and as directed.

M&L Sheet Glass, Ordinary, 5.0mm thick, Glazing in Wooden/Metal Frames and glazed with Beads or Oil Putty, area exc. 0.50 SQM in Each Pane, complete all as specified and as directed.

Repairs the leakage in the existing 15 mm bore pipe line by providing elbow/union/socket/tank nipple/nipple upto 200 mm, complete all as specified and as directed.

Repairs the leakage in the existing 20 mm bore pipe line by providing elbow/union/socket/tank nipple/nipple upto 200 mm, complete all as specified and as directed.

S&F of PVC bend pipe for PVC 10 ltr flushing cistern for EWC / IWC as in repairs, complete all as specified and as directed.

Repairs of leakage of any type by providing M-seal, complete all as specified and as directed.

Supply & laying Steel Water Tubing 15mm bore (dia), galvanised, ‘medium grade’ with all Fittings, fixed on walls, ceiling or laid in floors or any other situation, complete as all specified and as directed.

All as per Item no. 109 here in before but for 20 mm, complete all as specified and directed.

S&F in repair Rotational Moulded Polyethene Water Storage Tank 500 Litre Capacity (Cylindrical, Vertical with Closed Top), 3 layered, hoisted and fixed in Position all as specified in MES Schedule including wash out GI Pipe 32mm of 450mm length with stopper, complete all as specified and as directed.

S&F in repair Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity (Cylindrical, Vertical with Closed Top), 3 layered, hoisted and fixed in Position all as specified in MES Scheduleincluding wash out GI Pipe 32mm of 450mm length with stopper, complete all as specified and as directed. , complete all as specified and as directed.

Cleaning and removing all Scale dirt etc form PVC/RCC tanks and from mouths of circulating pipes including washing and old damaged PVC tank lid, capacity of tanks exc. 250 liter n.exc 500 liter., complete all as specified and as directed.

All as per Item no. 113 here in before but capacity exc. 500 liter and n. exc. 1000 liter, complete all as specified and directed.

S&F in repair PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or in Floors complete all as specified and as directed.

All as per Item no.115 here in before but for 110 mm, complete all as specified and directed.

S&F in repair PVC (SWR) 75mm bore (dia), Branch Piece, Single (Single Y) Equal or Unequal with Access Door, etc. jointing with Solvent Cement, complete all as specified and as directed.

S&F in repair PVC waste pipe 32 mm dia with coupling suitable for urinal and wash hand basin down pipes of required length, complete all as specified and as directed.

S&F in repair Pillar Tap 15mm bore (dia) fancy type, Cast Copper Alloy, Chromium Plated with Capstan Heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed Shanks and Fly-nuts, screwed for Iron Pipe and fixed, complete all as specified and as directed.

S&F in repair Stop Valve 15mm bore (dia), Fancy type, chromium plated, screwed down, high pressure, with Crutch or Butter-fly Handle, screwed both Ends for Iron Pipe or for Unions and fixed, complete all as specified and as directed.

S&F in repair Stop Cock 15mm bore , Chromium Plated with long shank, Concealed type, screwed down high pressure with Crutch or Butter-fly Handle, screwed both Ends for Iron Pipe or for Unions and fixed, complete all as specified and as directed.

S&F in repair fancy type CP, 15 mm dia twin angle cock, cast copper alloy screwed above high pressure with crutch or butterfly handle and screwed both ends for iron or for union, complete all as specified and as directed.

S&F in repair CP jet pressure for EWC including PVC Connection, complete all as specified and as directed.

S&F 15mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed (as approved), complete as directed complete all as specified and as directed.

All as per Item no.124 here in before but for 20 mm, complete all as specified and directed.

S&F in repair Ball Valve 15mm dia (minimum Weight 210 Gram), high pressure of PTMT with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and fixed, complete all as specified and as directed.

S&F in repair Vitreous China White Squatting Pan, ‘Orissa’ Pattern of size 580x440 mm with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan incluiding provision of Lime Concrete Bedding and Making Good to Floor/distrubed surfaces and fixed, complete all as specified and as directed.

M&L Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with Trap and Fixing Bolts (excluding Flushing Cistern and Flush Pipe) including connection to drain (or outgoing pipe) and to Flushing Pipe, Anti-syphonage Pipe, etc. and Making Good to Floor /distrubed surfaces and fixed-in-repair including health faucet with 1mtr long easy flex tube in chrom finish & wall hook, complete all as specified and as directed.

S&F in repair PVC Connection Pipe 15mm in size with PTMT Nuts of length 450mm and fixed, complete all as specified and as directed.

S&F in repair Brass Chromium plated Tubular Towel Rail, 20mm dia, D-type, 60 Cm long between Flanges with Bracket (one Pair) and fixed, complete all as specified and as directed.

S&F in repair Vitreous China Wash Hand Basin 550x 400mm in size, White (Flat Back or Angle Back Type) with 32mm bore waste coupling of PTMT (half or full threaded of minium weight 32-445gms), a Pair of Cast Iron Brackets duly Painted/ Erecting Stand including Cutting and Pinning in Ends, Making Good disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

All as per item No-132 here in before but refixing in repairs including providing / repairs of waste pipe and waste coupling, complete all as specified and as directed.

S&F in repairs to CP health faucet of 15 mm bore fixing to 15 mm bore pipe, complete set all as specified and directed.

S&F in repair 15mm bore CP Brass Wall mixer 3 in 1 Chromium plated for mixing hot and cold water screwed down for iron pipe and fixed with connections with and including L bend for shower provision complete all as specified and directed.

S&F in repair bib Tap 15mm bore (dia), Cast Copper Alloy, Chromium Plated with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed, complete all as specified and as directed.

S&F in repair bib Tap 15mm bore (dia) Fancy Type, Cast Copper Alloy, Chromium Plated with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed, complete all as specified and as directed.

S&F in repair PTMT grating Doom 100mm dia (minimum weight 25 Grams) complete all as specified and as directed.

S&F in repair Brass Chromium plated Shower Rose 125mm size, with or without Swivel Joints, and fixing to Steel Pipe or Union and fixed, complete all as specified and as directed.

S&F in repair PVC Flushing Cistern 10 Litre capacity White, Low Level, valve less, syphonic action type with Inlet, Ball Valve, Float and handle, a pair of Cast Iron Brackets Erecting Stand duly painted including cutting and pinning in ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and fixed, complete all as specified and as directed.

S&F in repair Sheet Glass Shelf Assembly consisting of 5.5mm thick Sheet Glass Shelf 12 Cm wide with Chromium plated Bracket Guard and Railing 60 Cm long and fixed, complete all as specified and as directed.

S&F in repair Sink with Drainage Board made of Stainless Steel l.0mm thick Kitchen or Laboratory Overall size 915x460mm Bowl size 410x330x 160mm with Plugs, Washers and Wastes, etc. including bedding in Cement Mortar to Dwarf Wall or including fixing Cantilever Brackets and connecting Union to Pipe,Making Good disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

M&L for 12 mm thick particle board for insulation purpose fixed with nail to timber frame work at any position, complete all as specified and as directed.

S & F 4mm thick Asbestos cement building boards fixed to timber frame work in ceiling, complete all as specified and as directed.

S&F in repairs in patches n. exc. 5 square meter each, GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste, complete all as specified and as directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., conforming to Fe 290-W (Gde E-165) quality A, drilled for fixing of steel sheeting or other covering Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening,complete all as specified and as directed.

S&F of Structural steel, rolled section as in main and cross beams, hips and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming to Fe-410 W (Gde-E-250), complete all as specified and as directed.

M/S Krishna Construction Co.

M/S Mahabir Traders

M/S SUNNY ENTERPRISE

Satya Enterprises

M/S Singha Enterprise

M/S Yadav Corporation

BEE KAAY TRADERS

M/S Himalayan Trading Co