Construction of 36 Nos. Type-II residences near police wireless offie at Dhorankhas in distt. Dehradun

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. (NALA & culvert)

Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the xisting floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Filling available excavated earth (excluding rock) in trenches ,plinth,sides of foundation etc . in layers not exceeding 20cm in depth ,consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m .

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete 1:4:8 (1cement :4 coarse sand:08graded brick aggregated 40mm .nominal size.) excluding the cost of centering and shuttering - All work upto plinth level

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (For height upto 5 m) P.C.C. grade M 20 Nominal mix (1:2:4)

Providing concrete for plain/ reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203P.C.C. grade M 20 Nominal mix (1:2:4)

Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion 1:4:8 in foundations and floors including supply of all material, labour and T&P etc. required for proper completion of the work. as per drawings and technical specifications Clause 802, 803, 1202 & 1203(Nala)

PCC 1:3:6 in Foundation(Plain cement concrete 1:3:6 mix with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.)

40 mm. thick cement concrete flooring 1 :2 : 4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm. nominal size ) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1cement :3 coarsesand : 6graded stoneaggregate 20mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

Providing and laying Reinforced cement concrete in sub-structure complete as per drawing and technical specifications RCC Grade M35

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :.1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).All works upto plinth level

Extra for providing richer mixes at all floor levels. Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).All works above plinth level upto floor V level

Extra for providing richer mixes at all floor levels. Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @340 kg/cum) TOTAL R.CC FIFTH TO EIGHTH FLOOR

Extra for providing richer mixes at all floor levels. Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @340 kg/cum) EXTRA FOR RCC /B.M.C/R.M.C WORK work above floor V level for each four floors or part thereof.

Extra for providing richer mixes at all floor levels. Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @340 kg/cum) EXTRA FOR RCC /B.M.C/R.M.C WORK work above floor V level for each four floors or part thereof.

Add for using extra cement in the items of design mix over and above the specified cement content therein

Centering shuttering including strutting, propping etc. and removal of form work FOUNDATION UP TO PLINTH

Centering shuttering including strutting, propping etc. and removal of form work COL SUPER STRUCTURE

Centering shuttering including strutting, propping etc. and removal of form work Roof Beam

Centering shuttering including strutting, propping etc. and removal of form work Slab

Centering shuttering including strutting, propping etc. and removal of form work Staircase

Centering shuttering including strutting, propping etc. and removal of form work Lintel+sunshade

Centering shuttering including strutting, propping etc. and removal of form work R.C.C Base Shuttering

Centering shuttering including strutting, propping etc. and removal of form work R.C.C Wall

Reinforcement for R.C.C work including straighting,cutting,bending ,placing in position and bending all complete Thermo-Mechanically Treated bars.

Supplying, fitting and placing TMT bar reinfircment in superstructure complete as per drawing and technical specifications Clauses 1002,1010 and 1202

230 th Brick work with brick of class designation 75 in foundation & plinth in cement mortar 1:6

Brick work with F.P.S bricks of class 75 in super structure above structure above plinth level up to floor five level in all shapes and sizes in cement mortar 1:6 (1 cement : 6 coarse sand )

Half brick masonry with F.P.S bricks of class designation 75 in superstructure above plinth level up to floor five level in cement mortar 1:4 ( 1 cement : 4 coarse sand)

Extra for providing and placing in position 2 Nos. 6mm dia. M.S.bars at every third course of half brick masonry (with F.P.S.bricks).

Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204 Random rubble masonry In cement mortar (1:5)

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing/fixing T-iron frames for doors,windows and ventilators of mild steel tee-section, joints mitred and welded with 15X3 mm lugs 10cm long embedded in cement concrete blocks 15X10X10cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with dash fastener or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws Second class teak wood

Providing and fixing factory made ISI marked steel glazed doors, windowsand ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing/fixing Gate of riquired pattern in frames of windows etc. with M.S. flat, square or round bars etc. all complete Fixed to steel windows by welding.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding

Providing fitting and fixing mild steel railing complete as per drawing and technical specifications Clause 1208.2

Providing & fixing of wire mesh (mosquito jalli) with labour & material comlete With 12 mm mild steel U beading.

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with 4.0 mm thick glass panes

Providing/fixing M.S. railing of required pattern in frames of windows etc. with M.S. flat, square or round bars etc. all complete M.S. tube

Providing and fixing cup board shutters with 25 mm thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make, including IInd class teak wood liping of 25 mm wide x 12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of Engineer-in-Charge

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately)

Providing and fixing chromium plated brass handles with necessary screws etc. complete:

Providing and fixing aluminium sliding door bolts, ISI marked anodised(anodic coating not less than grade AC 10 as per IS : 1868),transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. Complete 100x10 mm

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Providing and fixing PTMT door catcher of length 72 mm and dia. of 42 mm with suitable washers weighing not less than 33 gms.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.18 mm thick

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement basedhigh polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 500x500 mm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete

P/F 1st quality ceramic glazed wall tiles conforming to IS : 15622 of approved make in colours , shades except burgandy , bottel green , black of any sizes as approved by Engineer -in -Charge in skirting , risers of steps and dados over 12 mm thick bed of cement mortar 1:3 and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Udaipur green marble

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

12mm thick plaster on the plain in side of mix 1:4 ( 1 cement : 4fine sand) mortar

15mm thick plaster on the plain in side of mix 1:4 ( 1 cement : 4 fine sand) mortar

12mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar

15mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar

15mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. ( For third floor )

15mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. ( For forth floor )

15mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. ( For fifth floor )

15mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. ( For sixth floor )

15mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. ( For seventh floor )

15mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. ( For eighth floor )

15mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. ( For ninth floor )

15mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. ( For mumty &machine room&perapet wall )

6mm thick cement plaster of ceiling of mix 1:3 ( 1 cement : 3 fine sand) mortar

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade Two or more coats on new work over an under coat of suitable sq.m shade with ordinary paint of approved brand and manufacture.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.)

Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, thetop most layer shall be finished with brick tiles of class designation10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixedwith 2% integral water proofing compound by weight of cement overa 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) andfinished neat (item of laying brick tiles shall be paid for separately).

Providing & Fixing decorative structure glazing work , including cost of adhesive of approved quality.5mm reflacted tougthend glass , aluminium section 2’’x2’’-16 gauge Silicon weither proof 789

Granular sub-base/base/surface course with local materials (Table 400.13) by mix in place method normal Construction of granular sub-base by providing local material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at once and compacting with smooth wheel roller to achieve the desired density complete as per Clause 401.4 as per Technical Specification Clause 408. Using Gravel mix soil Cum

Providing and Laying of Interlocking Concrete Block Pavements of M-40 Grade having thickness 80 mm as per drawings and Technical Specification Clause 1504.

Cement Concrete (PCC M-30) Pavement:-Construction of Un-reinforced, Cement concrete pavement, thickness as per design, over a prepeared sub base with 43 grade cement or any other type PCC Grade M-30, coarse and fine aggregates conforming to IS: 383,maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less then 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (Steel channel, laying and fixing of wedges, steel plates including levelling the formwork and laying and fixing of 125 micron thick polythene film, as per drawing), spreading the concrete with shovels, rakes, compacted using needle, and plate vibrators, finished in continuous operation and curing of concrete slabs for 14 days, using curing compound where specified and water finishing to lines and grade as per drawings and technical specifications

Construction of Embankment with Material Obtained from Borrow Pits Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20mm (T.V+Telephone+Network)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

Supplying and flxing brass batten/angle holder including connection etc. as required.

Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Providing and fixing plain 16/0.20mm (0.50sqmm) twin flat flexible, FRLS PVC insulated, copper cable, in PVC sleeve of suitable size on the floor/ wall, or side of the table/ door etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 1 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 2 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 3 run of cable

Supplying and fixing following way prewired TP&N MCB distribution board of steel sheet for 415 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FRLS PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.(But without MCB/ RCCB/ Isolator) 4 way (4 + 12), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supply of AC 230/250 volts, 50 HZ energy efficient ceiling fan with standard down rod, blades, 2 nos. caps etc. Complete. (Make : Bajaj /Compton / Havells) 1200 mm sweep

Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. Complete (Make : Bajaj /Compton / Havells) 300 mm sweep 900 rpm

S/F hexagonal fan box with hexagonal side of approx 80mm in length fabricated from 16 SWG M.S. sheet incorporating 16mm dia. M.S. round bar duly bent for supporting fan hanger duly painted with red oxide and screwing arrangement with wiring conduit laid in the R.C.C. roof before concreting Alongwith supply of all material, labour T&P required for proper completion of work.

Supply and fixing of 16 gauge M.S. drum duly painted including making hole in the wall for exhaust fan and finishing properly complete in all respects. For 12" dia MIRROR LIGHT

Supply and fixing of 300mm Exhaust fan louvers/shutters.

Supply of LT XLPE PVC aluminium Unarmoured cable 50 Sq.mm 4core 1100 volt.

Supply of LT XLPE PVC aluminium Unarmoured cable 150 Sq.mm 4core 1100 volt.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe FRLSom earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, copper tube, having single prong at top, with 85 mm dia 6 mm thick copper base plate including holes etc. complete as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 35 sq. mm and upto 95 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 95 sq. mm and upto 185 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 50 sq. mm (35mm)

Supply and installation of 6 mtr galvanised Octagonal pole with base plate 220x220 12 top 70mm & bottom 130 mm made up of 3mm thik suitable for max wind speed upto 160 km/hr. poles with single bracket

Supply & Installation of New generation, post-top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source as approved by Engineer in charge complete in all respect. (Rate taken from Havells Price List w.e.f. 1st july 2017). Model-RUBY (CLEAR) - IP65 Cat AA (seg.)

Supplying and laying of aluminium conductor PVC insulated armoured,served sheathed cable 1100 Volots grade at depth of 750 mm below ground lavel over a cushion of 75 mm . Thick sand around and protected with burnt bricks on sides and on top.On surface the cable run shall be fixed on M.s. clamp etc. of suitable size as or directed by the Engineer Incharge in all respects.The armouring of the cable shall be properly connected with the earth conductor by clamp etc.(havells.plaza) 50 sq.mm.3½ core Cat.A

S/F following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch TSO 100 series with contactors HRC fuses , isolating switch metering instrument & instrument box with CTs etc. in case of TPN , complete in all respect. 40 A TPN

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board 610x510 mm bowl depth 200 mm

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing G.I. pipes complete with G.I. fittings andclamps, including cutting and making good the walls etc. Iinternal work - Exposed on wall 15mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings andclamps, including cutting and making good the walls etc. Iinternal work - Exposed on wall 25 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings andclamps, including cutting and making good the walls etc. Iinternal work - Exposed on wall 50 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings andclamps, including cutting and making good the walls etc. Iinternal work - Exposed on wall 80 mm dia. nominal bore

Providing and fixing ball valve (brass) of approved quality complete High or low pressure with plastic floats 25 mm dia. nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 15mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110MM

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 100 MM

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 75 MM

Providing and fixing 600 x 455 mm. bevelled edge mirror of Saint Gobin or Modi float glass complete with 6 mm. thick hard board ground fix to wooden cleats with CP brass screws and washers etc. complete.

Providing and fixing terminal guard : Sand cast iron S&S as per IS - 3989

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : Sand cast iron S&S as per IS - 3989

Providing and fixing soil, waste and vent pipes : Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 : 100 mm dia

Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter : 100 mm dia

Providing & Fixing C.P. brass bib cock parryware make

Providing & Fixing C.P. brass Long boddy bib cock

Providing and fixing PTMT pillar cock of approved quality and colour

Providing & Fixing C.P. brass stop(conceald)

Providing & Fixing C.P. brass angle valve

Providing & fixing c.p. soap dish parryware make

Provding & Fixing C.P Towel rail parryware make

Provisiding & Fixing C.P Paper Holder parryware Make

Providing & fixing Over Head Shower parryware make

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 32 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 40 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.65 mm dia nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 80 mm nominal bore

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 coarse sand (Zone III) : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 455x610 mm and 45 cm deep for single pipe line :for sanitary building (Sewage)

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 coarse sand (Zone III) : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (R.W.H.T)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 100 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :300 mm dia. R.C.C. pipe

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200mm

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge.

Providing & fixing of R.C.C manhole covering tank (600 x 600)

Providing & fixing of foot rest in tank

Transporation of suitable truck mounted Odex/DTH drilling ring allong with all necessary accessories,T & P required for drilling and errection & dismentelling of rig machine including loading,uploading complete in all respects

Drilling of Bores as per is 2800-1979 using odex ii5(tubex) atapent required Drilling in Alluvial boulder,pebbles,pebbles,gravels, rocky stones,sticky clay etc.including of attechment consumbel stores bits water etc complete

Supply 125 dia 5.4 mm thick mserw fincut casting pipes complete in all respects(tolerance as per IS 4270-2001).

Supply 125 dia 5.4 mm thick mserw fincut perforated casting pipes complete in all respects(tolerance as per IS 4270-2001).

Supply & fixinf of suitable casting shoe of En-24 steel as per requirement of ODEX attachments complete in all respects

chemical & Becteriolgical test of water

Development of tube by air compresor

Development of tubewell by OP unit

Supply instailation,testing & commissioning of suitable duty submersible pumping plant complete with all accessories of suitable duty 15HP WC6BI-15/15/12

Supply of suitable penal cum starter (spare set)

Supply & installation of electromechanical,chicra,fating Plant

Supplying and fixing Single Headed Internal Hydrant Valve oblique pattern with instantaneous Stainless Steel coupling of 63 mm dia with cast iron wheel ISi marked, conforming to IS : 5290 (LTB2 ), with 80mm dia flanged inlet with ABS cap and chain complete with all accessoriesWATER TEST 21 Kgf/CM, 900 LPM DIS etc., as required.Nos. 10 7740 77400 Make Atasi / Andex

Supply, Installation, Testing and Commissioning 100°/o synthetic flax canvas Non-percolating FIRE hose (Type A), LS.I 636 marked 163mm dia x 1Sm long with stainless steel male & female couplings (IS 903 marked 63 m.m. dia x 15 m long with stainless steel male and female couplings (IS 903 marked) bound and rivited to hose pipes with G.I. rivits and copper wire as required.

Supply ,installation testing and commissioning of 63 mm dis. Stanless steel Branch nozzale 18:903 material LTB-2 tested at 21 kgflcm2 hydraulic test na swater test at 14 Kgf/CM2

Supplying and Fixing First Aid Hose Reel, wall mounting swinging type complete with drum & bracket of MS construction! spray painted in Post office Red, confirming to IS 884/1995 with upto date amendments, complete with the following as required: - a 30 Meter long 20 mm dia water hose Thermoplastic (Textile reinforced) Type - 2 asper IS:2585 b 25 mm dia gun metal ball valve & abs nozzle. c Drum and brackets for fixing the equipments on wall. d Connection from riser with stop valve (gun metal) & M.S. Pipe .

Supplying, installation, testing and commissioning of weather proof M.S cabinet size 900 mm x 600mm x 300mm deep fabricated from 1.6mm thick M.S. sheets and M.S angle 40mm x 40mm x 6mm complete with glass, locking arrangements to accommodate the following: - with key stand The cabinet shall be painted with one coat of primer and 2 coats of synthetic enamel paint of approved red shade

Providing and fixing single stainless steel wight app 22-25 Kg suction collecting head as per IS : 904-1983, hose coupling (draw out connection) with female outlet as per 903 cpmplete with 150 m.m.dia G.I. suction pipe with puddle flange with strainer complete as per drawings.

Supply and installation testing of cat Iron body Non Return valve with nuts, bolts.\Washer, etc compte in all respects 100 mm Make Kartar / Castel

Supplying, laying.fixing, testing and commissioning of following sizes (NB) of ISI marked heavy ·s·c1ass M.S. pipes including cutting, threading, welding ,etc. and providing all fittings e.g. elbows, reducers, ctamps, hangers. flanges, gaskets, nuts. bolts and washers etc. including painting of pipes and fittings with red paint over a coat of raedy mixed primer of following sizes 150m.m. dia

Supplying, laying.fixing, testing and commissioning of following sizes (NB) of ISI marked heavy ·s·c1ass M.S. pipes including cutting, threading, welding ,etc. and providing all fittings e.g. elbows, reducers, ctamps, hangers. flanges, gaskets, nuts. bolts and washers etc. including painting of pipes and fittings with red paint over a coat of raedy mixed primer of following sizes 100 m.m. dia

Supplying, laying.fixing, testing and commissioning of following sizes (NB) of ISI marked heavy ·s·c1ass M.S. pipes including cutting, threading, welding ,etc. and providing all fittings e.g. elbows, reducers, ctamps, hangers. flanges, gaskets, nuts. bolts and washers etc. including painting of pipes and fittings with red paint over a coat of raedy mixed primer of following sizes 80 m.m. dia

Supplying, laying.fixing, testing and commissioning of following sizes (NB) of ISI marked heavy ·s·c1ass M.S. pipes including cutting, threading, welding ,etc. and providing all fittings e.g. elbows, reducers, ctamps, hangers. flanges, gaskets, nuts. bolts and washers etc. including painting of pipes and fittings with red paint over a coat of raedy mixed primer of following sizes 25 m.m. dia

Supplying, Installation; Testing and Commissioning of Butterfly valves of PN 1.6 rating of following sizes with nitrile Bronze I G.M. seat duly ISi marked and stainless steel stem with lever/gear operation and cast iron body in powder coated finish for fire fighting application complete in all respects confirming to IS: 13095 as required. 100 MM dia

Supplying, Installation; Testing and Commissioning of Butterfly valves of PN 1.6 rating of following sizes with nitrile Bronze I G.M. seat duly ISi marked and stainless steel stem with lever/gear operation and cast iron body in powder coated finish for fire fighting application complete in all respects confirming to IS: 13095 as required. 80 MM dia

Providing, Installation, Testing and Commissioning of Gun Metal Bal Valves with brass body chrome plated of following sizes as required. 25 mm dia

Supply, Installation, Testing and Commissioning of 80 mm dia type Pressure Gauge including siphon pipe having calibration of 0 10 Kg I cm2

Providing, Installation, Testing and Commissioning of Air release valve with brass bod chrome plated of following sizes as required.

Supply testing and commissioning G.matel Foot valve 150 mm

Supply testing and commissioning G.matel Foot valve 100 mm

Supply testing and commissioning of electric Driven Jockey Pump suitable for auto/manual operation and consistion of horizontal centrifugal & suction back pullout type capable ot delivery 7.5 H.P 70 mtr. Head model 32/30

Supply and installation of A.B.C POWDER TYPE MONO AMMONIUM PHOSPHATE RATEING WITH GOOD BODY SIZE 1.6 MM MILD STEEL BODY EXTINGUISHER MEDIA ASPER IS 14609/IS4308 PROPELLENT NITROGEN/ SERVICE PRESSURE 15 KGF/CM2, HYDRAULIC TEST PRESSURE IS 35 KGF/CM2 AND ISi MARKED AS PER IS 15683 WITH ALL ASSOSORIES OR ALL CATIFICATE OF GOV. STANDERD 2 KG (FIRE RATING 1A & 88)

Supply and installation of A.B.C POWDER TYPE MONO AMMONIUM PHOSPHATE RATEING WITH GOOD BODY SIZE 1.6 MM MILD STEEL BODY EXTINGUISHER MEDIA ASPER IS 14609/IS4308 PROPELLENT NITROGEN/ SERVICE PRESSURE 15 KGF/CM2, HYDRAULIC TEST PRESSURE IS 35 KGF/CM2 AND ISi MARKED AS PER IS 15683 WITH ALL ASSOSORIES OR ALL CATIFICATE OF GOV. STANDERD 4 KG (FIRE RATING 2A & 218)

Supply and installation of A.B.C POWDER TYPE MONO AMMONIUM PHOSPHATE RATEING WITH GOOD BODY SIZE 1.6 MM MILD STEEL BODY EXTINGUISHER MEDIA ASPER IS 14609/IS4308 PROPELLENT NITROGEN/ SERVICE PRESSURE 15 KGF/CM2, HYDRAULIC TEST PRESSURE IS 35 KGF/CM2 AND ISi MARKED AS PER IS 15683 WITH ALL ASSOSORIES OR ALL CATIFICATE OF GOV. STANDERD 6 KG (FIRE RATING 3A & 21B)

SUPPLY AND INDSTALLATION OF CLEAN AGENT ACTUALLY WORKS ON FLAMMABLE LIQUIDS.GASES AND ELECTRICAL STARTED FIRE AS IS CODE 15683 ,FILLING RATIO 0.667 TEST PUESSURE 250 . KGF/CM2, OPERATING TEMPERATURE -20C* TO -55*C DISCHARGES 95 o/o FIRE RATING 21 B MAKE ATAS I'/ ANDEX I OEM 4.5 KG TYPE (FIRE RATING 21 8)

SUPPLY AND INSTALLATION OF WATER CORSON DI-OXIDE 50 LTR . WHEEL MOUNTEDAN D STAND FIRE EXTINGHUSERW C02 ACTUALLU WORKS ON PAPER, WOOD, PAPER, PLASTIC, ETC AS PER IS 904 CATIAGE TYPE MAKE ATASI'/ ANDEX

SUPPLY AND INSTALLATION OF FOAM TYPE(AFFF 50 LTR. WHEEL MOUNTEDAND STAND FIRE EXTINGHUSER S ACTULY WORKS ON PAPER, WOOD, PAPER, PLASTIC,PTROL DIESEL PAINTS RUBBER WAX LAC AND ALL VOLATILE LIQUIDS ETC AS PER IS 904 CATTAGE TYPE MAKE ATASI'/ ANDEX

AIR RELEASED TANK WlTH SlREN

S/F Kirlosker Deisel Engine With Pump & auto start Compleat with all ascessories , fixed in all .

S/F of Morley / Honeywell Panel HRZ-8e, 8 zone fire alarm control panel, 8 detection zones, 2 sound outputs, surface mounting, fire and fault relays, 318 x 356 x 92 m.m. (HxWxD)

S/F of Morley / Honeywell photoelectric smoke detector, Low profile design, low current draw, wide operating voltage 8 to 30 VDC, Bi-colour LED detector , status indicator, Automatic drift compansation, programmable sensistivity, Advance maintenance features via remote handheld test unit, tested and approved to EN54- 7:2000

S/F of Morley / Honeywell detector base 2 wire plug in detector base for series 300 detectors.

Thermal detector, low profile design, Low current

S/F of Morley / Honeywell Sounder + Strobe Wall mounted Horn/Strobe, 12/24V red, Multi Candela 15, 15/75, 30,75 ,110, 115 cd, Plain (No lettering)

S/F of Morley / Honeywell manual call point MCP yellow, Dual pole, Flexi Element with BB India.

S/F of Morley / Honeywell remote hand held progmmer and testS/F of Morley / Honeywell remote hand held progmmer and test unit.

S/F of Morley / Honeywell remote programming interface unit

S/F of Morley / Honeywell surface mounting kit. The beam SMK allows system sensor reflected beam detectors to be mounted when surface wiring is used.

S/F of Morley / Honeywell remote test station with key switch for use with beam and duct detectors

S/F of Morley / Honeywell remote test station with key switch for use with beam and duct detectors. 2.5 units

Two core shielded 1.5 m.m. wire for connections

ABC fire fighting cylinders 2/6 Kg for all type of fire

S/F of Modular fire extinguishers clean agent capacity 2Kg area of coverage approx 3 m. powder coated anti corresive charged weight 3.5 kg approx. charged pressure 15 kg approx. ceiling mounted type.

Supply,installation,testing &Commissioning of Sewage Treatment Plant ( 1MLD)

MAHALAXMI BUILDWELL(INDIA) PVT. LTD.