SPECIAL REPAIRS OF BLDG NO P-45, P-46 AND P-47 AT MILITARY HOSPITAL IN ARMY AREA JODHPUR UNDER GE (ARMY) NO 2 JODHPUR

Amount

Demolition of cement concrete of any description and in any position not otherwise specifically provided for (such as copings, bands of any type, roof padding, kerbs, sunken etc; overall thickness and removing the dust debris etc to a distance outside MOD land from site and disposing the same complete all as specified and as directed.

Dismantling stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar complete all as specified and as directed.

M&L Jodhpur stone roof slabs, self faced exceeding 10cm but not exceeding 12.5 cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in cement mortar 1:3 complete all as specified and as directed.

-ditto- all as per item No 3 above but, except stone complete all as specified and as directed.

M&L for plain cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregates as over roof for making good depression/ undulation to make the existing roof surfaces as filling in depression of roof slab/ floor padding etc complete all as specified and as directed.

M&L for carrying out water proofing treatment for roofs in the following stages - (i) Rendering 10 mm thick plaster/ screed in cement mortar (1:4) mixing with water proofing compound (as per manufacturer instructions) and surfaces finished even and smooth without using extra cement all as specified . Note : (WPC shell be measured separately and paid for under respective item of schedule). (ii) First coat of bitumen primer conforming to IS-3384 @ 0.40 Kg/Sqm over plastered surfaces. (iii) Second coat of bonding material using blown type bitumen conforming to IS-702 grade 85/25 @ 1.20 Kg/Sqm. (iv) Third layer of APP modified polymeric membrane centre core of 20 micron HMHDPE outer film 20 micron both sides thickness 2.0 mm having weight 2.50 Kg/Sqm. (v) Final coat of blown type bitumen confirming to IS 702-1988 grade 85/25 @ 1.2 Kg per Sqm.

Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 9 to 10 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterpro of and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including providing skirting upto 150 mm height along the parapet walls in the same manner complete all as specified and as directed.

Supply only integral water proofing liquid ISI marked

Taking down carefully cement concrete/ spalled out concrete from RCC roof projections,Ceilings,Sunshades,beams etc upto cover depth by chipping out lightly including necessary scaffolding etc complete all as specified and as directed.

M&L for cleaning the existing reinf of slabs chajjas etc & applying a coat of SIKA RUSTOFF 11 or equivalent of pidilite,fosroc,Thermax etc to remove rust particles etc throughly cleaning the surface complete all as specified and as directed.

M&L for applying a coat of bond coat made with cement slurry(1part cement to 1.5-2parts water) mixed with admixture LATEX POWER mixed @5 Kg per 50kg of cement & applying to the concrete surfaces @200gm/sqm to obtain tack complete all as specified and as directed.

M&L for 15-20mm thick rendering in CM 1:1:2 using 1 part cement to 1part 2-3mm screenings of stone agg & 2 parts coarse sand over the bond coat applied surfeces with cement mixed SIKA PLASTOCRETE admixture equivalent of pidilite,fosroc,Thermax etc @100gm/50kg of cement & finishing the surfaces even & rough to recieve final rendering coat including GI chicken wire mesh of 0.71mm dia wire & 12mm mesh size fixed with nails & screws complete all as specified and as directed.

M&L for 10-15mm thick rendering in CM 1:3 over the bond coat applied surfeces with cement mixed SIKA PLASTOCRETE SUPER admixture @100gm/50kg of cement & finishing the surfaces even & smooth complete all as directed at site complete all as specified and as directed.

S&F GI chicken wire mesh of 0.71mm dia wire & 12mm mesh size fixed with nails & screws around RCC chajjas/fascias etc complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor not exceeding 15cm thickness below or above ground level including floor finishes and removing debris from the site all as specified and as directed.

Dismantling glazed tiles/ kota stone/ terrazzo tiles any type as in dado/ skirting etc; including cement mortar bedding ( but not backing ) complete all as specified and as directed.

M&L for non skid ceramic coloured tiles of approved shade and pattern, 7 to 8 mm thick , area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm laid in floor, set and jointe (square/ rectangular) in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of approved shade and pattern of size 350x 250x7mm/ 450X350X7mm/ 300X450X7 to 8mm thick or any other nearer size as approved by Engineer incharge in vertical surface set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 as in backing coat of tiles complete all as specified and as directed.

M&L for virified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for virified ceramic tiles 10 mm thick (square/ rectangular) polished, as in skirting (Matching with floor tile of the same room) set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L for 16 -18mm thick granite (colour as approved) work (table rubbed and polished) in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for 16 -18mm thick granite (colour as approved) work (table rubbed and polished) in steps, shelves, jambs, pillars, window-cills, cooking platforms (vertical/ horizontal) and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 10mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 18-20 mm (+ 2mm) thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for mirror polished machine cut Kota stone slab 15-16 mm thick in riser of steps, skirting, dado and pillar laid over and including 10mm thick rendering in CM 1:4 and jointed complete all as specified and as directed.

Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, 50 mm thick, surfaces finished even and fair without using extra cement including provision of construction joints complete all as specified.

M&L for Stone slab 25 mm to 35 mm thick dressed true and square, in one length not less than 60cm and n. exc 120cm in as in Plinth Protection, chajja etc., punched dressed on exposed faces and self faced on the embedded unexposed beds and joints; exposed edges rounded or chamfered as directed, set, jointed and pointed in CM in 1:4 complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D-2, (40mm graded stone aggregate) as in sub floor, sub bases, floor and paving etc complete all as specified and as directed.

M&L for 60mm thick factory made pre cast cement concrete rubber moulded laquer finish using chemical and admixure inter locking tiles having compressive strength not less than 350 kg/Sqcm, of shape and colour as approved by GE , laid over 25mm thick compacted approved sand cushioned surface, joints filled by fine sand and compacting the top surfaces of paver blocks after laid etc of approved make all as specified and as directed.

M&L for factory made precast cement concrete solid blocks M-30 Grade, using 20 mm graded crushed stone aggregate as in kerb stones of any size (with plain or interlocking joints as directed) set in cement mortar 1:4 for path edgings etc; embedded in position including all necessary excavation, tamping ground arround blocks and removal of rubbish/ surplus soil etc., complete all as specified and directed by Engineer-in-Charge.

M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in kerbs or benching etc including necessary form work complete all as specified and as directed.

Dismantling of stone/ brick work masonry, built in cement mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stone work, serviceable stone aside for reuse and removing unserviceable material in low laying area complete all as specified and as directed.

M&L for squared rubble walling jodhpur type, brought upto course, well bonded bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed.

-ditto- all as per above item but, except stone complete all as specified and as directed.

Extra over for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm and dressing face beds and joints as specified to squared rubble walling,Jodhpur type, brought upto courses all as specified and as directed.

M&L for brick work with fly ash bricks (old size bricks), straight or curved on plan exc 6mtr mean radius, built in cement mortar (1:6) complete all as specified and as directed.

Taking down cement plaster, any description, on brick or stone walls etc, including raking out joints, hacking for key, scrubbing down with water etc and disposal of debris complete all as specified and as directed

M&L for rendering 15 mm thick in CM 1:6 over stone masonary, concrete surfaces, finished even and smooth (without using extra cement) complete all as specified and as directed.

M&L for keyed pointing in square rubble course or uncourse walling in CM 1:4 complete all as specified and as directed.

M&L for 10mm thick rendering in CM 1:3 on ceiling surfaces finished surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for carrying out water proofing treatment for sunken portion in the following stages - (i) Taking down of existing sunken slab treatment from the sunken portion and cleaning the surfaces washing down with water and rubbish of the pemises , cleaning and filling cracks with sealing compound, brushing neat cement slurry @ 3.00kg/sqm and grouting 25mm thick cement concrete type B-0 (1:2:4) using 12.5mm graded stone aggregate on sunken slab portion and finishing the top surfaces even and smooth without using extra cement. (ii) M&L for two coat of acrylic cementitious water proofing coating (Dr FIXITpidifin 2k manufactured by M/s Pidilite Industries Ltd or equivalent) and followed by a overlay protective screed (10mm thick cement mortar (1:4) along with liquid water proofing compound approved make as per manufacturer's instructions) on top surfaces of sunken slab after preprations as mentioned above. Method of application for acrylic cementitious water proofing coating achieved as per manufacturers instruction complete all as specified and directed.

Dismantling cast iron work of any description and in any position complete all as specified.

S&F 100mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, laid in trenches or in floor etc; complete all as specified.

S&F 100mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, fixed to walls etc; complete all as specified.

S&F 75mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, laid in trenches or in floor etc; complete all as specified.

S&F 100mm bore pipe cast iron 'P' or 'S' trap, complete all as specified.

S&F 75mm bore pipe cast iron 'P' or 'S' trap, complete all as specified.

S&F 100mm bore pipe cast iron cowls, complete all as specified.

M&L cast iron up to 150mm bore fittings of Bends (any type, radious and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces, single branch, 'Y' junctions, double branch, cross (all sockets or socket and spigot) collars, caps and plugs etc complete all as specified and directed.

M&L 100mm bore cast iron pipes and fittings joints or connections are filled/ sealed properly by epoxy sealant of ISI mark or M-Seal (Make:- Dr Fixit) apply as per manufacturing instructions complete all as specified and directed.

M&L 75mm bore cast iron pipes and fittings joints or connections are filled/ sealed properly by epoxy sealant of ISI mark or M-Seal (Make:- Dr Fixit) apply as per manufacturing instructions, complete all as specified.

S&F for 100mm bore pipes stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall etc complete all as specified and directed.

S&F for 75mm bore pipes stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall etc complete all as specified and directed.

M&L cement concrete type E-2, 1:5:10 (40mm graded crushed stone aggregate) as in sunken portion complete all as specified.

S&F in repair 40mm bore steel water tubing medium grade galvanised inserted at the end of lateral slope projecting at least 15cm beyond the outer most projected part of the building below the drain pipe up to two storey construction as spout for sunken complete all as specifide.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but not exc 4.00 sqm each and removing from site or to store complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each and removing from site or to store complete all as specified and directed.

Taking down shutters any description exc 1.00 sqm but not exc 2.00 Sqm each and removing from site or to store complete all as specified and directed.

Taking down shutters any description exc 1.00 sqm but not exc 2.00 Sqm each and refixing the shutter in same opening after easing and adjusting complete all as specified and directed.

S&F of pressed steel framed made out of 1.25mm thick MS sheet, of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed.

S&F of pressed steel framed made out of 1.25mm thick MS sheet, of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in fillings and mass concrete, filling backs of chowkats etc complete all as specified and directed.

M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in lintels upto 1.50 m clear span, cills , steps, seismic and other similar bands, copings, kneelars, apex stones, bed plates, bed blocks of hold fasts etc including necessary form work complete all as specified and directed.

M&L 40mm thick flush shutter, solid core construction, with particle board core and plywood face panels, commercial type on both side complete all as specified and directed.

S&F of factory made 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) kiln seasoned and chemically pressure treated complete all as specified.

S&F of Factory made steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed Skeleton shutter jointed internally with flat iron 40x4mm complete including grill of 8/10mm square bars as directed by Engineer incharge, fixed horizontally @ 10cm c/c, hinges, handle, tower bolts, stops, lugs etc. (with provision of fixing for cooler if required) all as shown on drawing No CEJZ/TD/20 sheet 1/3 to 3/3 fixed in repairs i.e, incl taking down and removal of old steel windows from site or to store complete all as specified and directed. Note:- Guard bar/ grill shall be measured and paid separately under respective item of Sch 'A'.

M&L for fabrication of aluminium powder coated window any pattern & design (openable with hinges, sliding, tilt and turn, casement , fixed type, villa type, ventilators) fabricated with anodized aluminium rectangular or any type section in frame with approved design & patterns including provn of fixing galvanised mild steel wire cloth on the outer side of frame etc; fixed in position all as specified and directed. Note:- Glass pane & galvanised mild steel wire cloth shall be measured and paid separately under respective Items of Sch 'A'.

S&F for figured glass, pin head type ordinary quality, 4mm thick, area of each pane not exceeding 0.5Sqm and glazing with aluminium beading in aluminium frame all as specified and as directed.

S&F of sheet glass ordinary quality 4 mm thick and glazing with oil putty or fixed with wooden beads or fixed with rubber gasket in squares any size of pane complete all as specified & as directed.

.-Ditto- all as per above item but 4mm thick frosted glass complete all as specified and directed.

S&F of galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified & as directed.

Mild steel round bars welded to steel windows or ventilators as in guard bars framed or unframed complete all as specified & as directed by Engineer incharge. Note:- Guard bars shall be factory welded & given one shop coat of red oxide or zinc chromate primer. Cost of factory welding & Shop coat of primer is deemed to be included in quoted rates.

S&F of factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed.

S&F of solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S&F of 100 mm size PVC/ Stainless Steel (as approved by Engineer incharge) butt hinges all as specified and directed.

S&F mild steel door handles, stove enameled black, 150 mm long and fixed with steel screws complete all as specified.

S&F of mild steel barrel tower bolts, stove enameled black, with bright bolt, 150 mm long and fixed with steel screws complete all as specified and as directed.

S&F of 300 mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including bolts and nuts complete all as specified.

S&F of mild steel rat tail rod pattern helical door spring of size 300mm including roller and roller plate fixing to iron frame by welding complete all as specified & as directed.

Dismantling wrought iron or mild steel work of any description and in any position not otherwise specifically provided for (framed/ unframed work) complete all as specified.

S&F of framed work as in doors chowkats of MS angle iron or MS hollow square/ rectangular any type/ size with gusset plates, rails, braces,cooler stand, chajja framed complete drilled for fixing of door etc; to be prepared for hanging with and including hold fasts and locking arrangements confirming to FE- 290 (Gde-E- 165) complete all as specified and as directed.

S & F for Providing Kitchen Cabinet anti fungal,moisture resistence,anti borer,100% water Proof,flame retardant. in required sizes at site made out of 18mm thick 100% Solid WPC Plain board of required size 18mmthick(WPC) Wood polymer composite sheet & provision of shutters made out of 18 mm thick 100% Solid WPC Plain board all required brackets SS screws etc. The panels shall be fabricatedusing adhesive and screws where ever required. as per drawing and specification a.including taking down and removal of old unserviceable boarding of any description and in any position complete all as specified and as directed.

Providing and fixing (WPC) Wood polymer composite sheet (WPC) Wood polymer composite coated Pre-laminated (one side decorative & other side balancing lamination sheet) density 600 kg/m3, frame of width 150mm & 18mm thickness made out of extruded 18mm WPC sheet and joined with suitable Cement Solvent adhesive and screw.The frame shall be fixed to the wall using 75mm long M.S. Screws through the frame by using(WPC) Wood polymer composite fasteners. A minimum of 3 Nos. of screws to be provided for each vertical member & minimum 2 Nos. for horizontal member etc complete all as specified and as directed.

S&F of hydraulic hings for kitchen cabin door shutter of mild steel bright finish or elecrogalvanised, fixede with screw etc complete all as specified and as directed.

S&F of mild steel butt hinges 100mm long, medium weight cold rolled fixed with steel chowakats etc complete all as specified and as directed.

S&F of mild steel single action helical hinges 150-200mm long, suitable for 1000-1250mm wide wooden door fixed with steel chowakats etc; complete all as specified.

S&F of ball bearing single extension drawer slide (runner) 300-450mm clear slide and 25-30mm wide,fixed with screws etccomplete all as specified and as directed.

S&F of alluminium anodised handles 100 mm long fixed to windows all as specified and directed.

S&F of 50mm dia polished hard wood knobs fixed with screw complete all as specified and as directed.

S&F of decorative mild steel curtain rods 32mm dia (powder/ PVC coated) including fixing brackets & side cups complete fixed in repairs i.e., including taking down the existing unserviceable curtain rods complete all as specified and directed

S&F of powder coated aluminium anodised deco grill weighing not less than 1.40 kg/ sqm and fixing necessary joining cleats/ frame etc complete all as specified and as directed.

Taking down 15mm bore steel water tubing and connections etc, including cleaning for refixing or removal from site complete all as specified and as directed.

Ditto all as per item no 91 but Size 20 mm bore

Ditto all as per item no 91 but Size 25 mm bore

S&F of 15mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc incl cutting chasing and making good of disturbed surface complete all as specified and as directed.

Ditto all as per item no 94 but Size 20 mm bore

Ditto all as per item no 94 but Size 25 mm bore

Fixing only 15mm bore old servisable steel water tubing any grade with all new fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and as directed.

Ditto all as per item no 97 but Size 20 mm bore

Ditto all as per item no 97 but Size 25 mm bore

S&F in repair vitreous china squatting pan, Orissa pattern, size 580x440mm white/ coloured with integral foot rests including flus pipe and connection to trap, and to flushing pipe, anti-syphonage pipe etc complete all as specified and as directed.

S&F in repair PVC 10 ltr. Cap. valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc complete all as specified and as directed.

S&F in repair vitreous china wash basin, white/ coloured, flat back, size 550x400mm including PTMT waste fittings, 32mm bore size, waste pipe pvc 32mm bore and angle iron brackets of required size and length etc. and making good disturbed surfaces to match with the existing complete all as specified.

S&F in repair stainless steel sink, 1.00mm thick for kitchen, with plug, waste pipe, washers, including bedding in cement mortar on to dwarf walls, or including fixing cantilever iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair of stainless steel plate rack, made out of 0.63 mm thick sheet of size 0.40 to 0.60 Sqm and 20-25 cm deep as per standard pattern and design (approved quality) with plugs, screws, washers etc complete all as directed. Note : Weight of plate rack shall not be less than 5.00 kg each.

S&F of low density polythene pipe (LDPE) of pressure rating 6 Kg per Sq.cm, 450 mm long, heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipe as in repair complete all as specified and directed.

Disconnecting existing PVC tank exc 500 Ltrs and not exc1000 Ltrs setting aside (or lowering if required) for repairs, cleaning, etc and hoisting if required reconnecting refixing in position complete all as specified and directed.

S&F in repair 1000 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 25mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified in SSR Part-I complete all as specified.

S&F MS chromium plated peg set of 05 fixing with wall complete all as specified.

S&F as in Corner Glass shelf 250mm superior quality with CP tubular framing & brackets complete all as per sample complete all as specified and as directed.

S&F in repair Soap dish any type, fixed to plugs with chromium plated brass screws all as specified and directed.

S&F in repair tubular towel rail 20mm dia brass chromium plated `D' type 60cm long with bracket and fixed complete all as directed

S&F in repair 15mm bore chromium plated bib taps, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

S&F in repair for pillar tap, brass, 15mm dia, with capston heads, chromium plated, fancy type screwed down, high pressure, with or without lettered hot or cold, with long shank, screwed shanks and fly nuts, screwed for iron pipes or for wash hand basin all as specified and as directed.

S&F in repair 15mm bore stop valve/ angle stop cock chromium plated, fancy type cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe with long shank and cup complete all as specified and as directed.

S&F in repair 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified.

S&F in repair chromium plated shower roses 125mm size with or without swivel joints, any size, including fixing to steel pipe or union suitable for 15mm bore pipe etc complete all as specified and as directed.

S&F in repair Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and as directed.

S&F in repair CP greating doom 100mm dia complete all as specified and directed.

S&F 20 mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight for 25mm ball valves-455gms) fixed in repairs i.e., incl taking down and removal of old unserviceable float valves complete all as specified and as directed.

Preparing new or previously untreated surfaces of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Preparing new or previously untreated surfaces of steel or iron work of any description and girth over 10cm and applying two coats of synthetic enamel paint complete all as specified and directed.

Preparing new plastered surfaces and M&L for applying chalk whitening/ concrete primer and /or cement base putty as required incl preparing the surfaces smooth by rubbing and / or sandpapering and two coats of Distemper oil Emulsion on new plastered surfaces all as directed by Engr in charge.

Preparing new plastered/ pointing surfaces and M&L for applying concrete primer and /or cement base putty as required incl preparing the surfaces smooth by rubbing and / or sandpapering and two coats of cement base paint on new plastered surfaces complete all as specified and directed.

Preparation of new plastered surfaces of walls etc. & applying three coats of lime white wash on walls complete all as specified and directed.

Preparation of new plastered surfaces of ceiling etc. & applying three coats of lime white wash on ceiling complete all as specified and directed.

Preparing of old painted wooden surfaces or wood based material of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

Preparing old painted steel surfaces or iron work of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

Preparing old plastered surfaces brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots incl washing , rubbing down and stopping of distempered or painted surfaces and M&L for applying one coat of distemper oil emulsion on old plastered surfaces complete all as specified and directed.

Preparing old surfaces incl brooming surfaces, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil or greasy spots incl washing rubbing down and stopping of distempered and painted surfaces and M&L for applying one coat of cement base paint on walls etc complete all as specified and as directed.

Preparation of old decorated plastered surfaces of walls etc. & applying one coat of white wash complete all as specified and directed.

Preparation of old decorated plastered surfaces of ceiling etc. & applying one coat of white wash on ceiling complete all as specified and directed.

Taking down carefully aluminum/copper point wiring (light/fan/ socket/ power) complete including fittings such as switch, socket, ceiling roses light fittings etc and and making good disturbed surface of wall complete all as specified and directed.

Material and labour for point wiring one light/exhaust/ceiling fan/Bell point controlled by one switch one way complete with 1.5 sq mm single core multi stranded copper conductor PVC FRLS insulated unsheathed 1100 Volt grade cable in and incl PVC FRLS CONCEALED CONDUIT PIPE (ISI Marked) with all accessories including new pressed steel terminal boxes (sunk in wall ) with 3.00 mm thick plastic laminated sheet top cover or PVC FRLS board including PVC FRLS top cover with 1.50 sq mm insulated unsheathed PVC FRLS multistranded covered copper conductor for common earth and connecting to earth dolly and making good disturbed surface of wall incl matching the colour of wall/ceiling with extisting wall/ceiling colour all as specified and directed

All as per item ser No 134 above but for one socket out let 5 Amps 5 Pin on same board with other switch

All as per item ser No 134 above but for One socket out let 5 Amps 5 pin on independent board

All as per item ser No 134 above but for one call bell point controlled by one bell push .

All as per item ser No 134 above but for one light point controlled by two switch two way

All as per item No 134 here in before but with single core multistranded cable of size 4 Sqmm for one 15 Amps socket outlet on independent board and multistanded insulated copper earth continuity conductor of size 4 Sq mm all as specified and directed

Material and labour for Elect bell AC 230 Volts single phase musical type.

Material and labour for bell push flush type 5 Amps .

Supply and fixing for Piano type switch 5 Amps one way.

Supply and fixing for switch 5 Amps single pole two way.

Supply and fixing for socket out let 2 in 1 multi pin 5 Amps flush type universal.

Supply and fixing switch piano15/16 Amps one way 240 volts

Supply and fixing socket outlet in repair 2 in 1, 3 pin, 5 and 15 Amps socket outlet 240 volts SP

Supply and fixing for Fan step regulator flush type

Supply and fixing Ceiling rose on PVC FRLS board size 65 X 50 mm three terminal Complete.

Supply and fixing Lamp Holder, PVC FRLS/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply and fixing box type powder coated luminaire LED 1X10 watt LED tube light with all accessories and necessary connection complete all as specified and directed.

S&F in replacement of LED light fitting 1 X 20 watt (4 feet), T5 Rechargable Emergency Batten Light, has power backup of 3 to 4 hours, a slim design with internal driver, complete with all accessories and making necessary electric connection from ceiling rose to fitting terminal, complete all as specified and directed.

Supply and fixing in replacement LED Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete

Taking down old sub main wiring and M&L for concealed sub main wiring with 2 run of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed medium grade, ISI marked, non metallic PVC conduit 20 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note : Two run of 6 Sq.mm. and one run of 6 Sq.mm (earth wire) cable incuding one run of conduit pipe will be measured as one length including making good the disturbed surfaces.

S&F in replacement of Distribution Board, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 12 way (Concealed flush to wall), 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. Note : 1. Blank plates will be included on the quoted rates. 2. All wires to be properly connected with copper lugs. 3. MCB will be measured and paid separately.

S&F in replacement of Vertical Distribution Board (Concealed flush to wall), double Door, suitable for 'A' Frame FP MCCB 100A made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, VTPN 4 way, 415 volts with bus bar rating 250 Amps, dust and vermin proof, suitable for incorporation of MCB’s and MCCB etc and making all necessary connections, duly flush of wall surface complete all as specified and directed.

S&F for MCCB, A Frame, thermal adjustable magnectic setting, Ics = 75% 16 kA, 415V, 100 Amp, 4 Pole MCCB with over load and short circuit protection, complete all as directed.

Taking down elctric energy meter and keep in safe custody of MES store after disconnecting all necessary connection complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 200 mm complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and directed.

Taking down ceiling fan from existing position and keep in safe custody for refix after complete of work by making all necessary connection complete all as specified and directed.

M&L for dismantling and Removing old burnt copper wire winding of ceiling fans of any size & sweep of any make and rewinding with new enameled super copper wire of existing gauge as per old copper winding incl providing insulation by varnishing (golden), cleaning, oiling, greasing etc complete all as specified and directed.

Supply and fixing in repair 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissionin

Supply and fixing MCB SPN, 32 Amp, B Curve 240 volts.

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core complete all as specified and directed.

Excavation in trenches n exc 1.5 mtr wide, n exc 1.5 mtr in depth and n exc 10 sqm on plain and getting out in hard/dense soil for cable, pipe etc complete all as specified and directed.

Returning, filling in, incl. spreading, leveling, watering and well ramming in layers n exc 25 cm deep in soft/loose soil complete all as specified and directed.

Removing surplus excavated rock to a distance not exc 50 m and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified and directed.

Supplying and laying (length perpendicular to axis of cable) un-reinforced precast concrete cable cover, ISI marked ,class LT, type 1, size 250mm x 150mm x 40mm duly embossed with "LT Cable 1100 Volts, cable size in SQMM" all as specified and as directed.

M & L for fine dry river sand cushioning by laying 8cm thick layer below the cable for making soft bed and 15 cm above the cable and then punning down to its consolidated thickness of 18cm after the cable is laid all as specified in SSR Part I and as directed.

Supply and lay 50 mm bore galvanised steel tubing Light grade with all fittings and fixtures laid in trench or ceiling or laying in floors complete all as specified and directed.

Supplying and fixing smart single phase two wire dual source prepaid energy meters BIS 15884 marked in existing meter board / florr panels with pre payment capacity touch keypad based digital having current range 10-60 Amp 240 Volt accuracy class 1.0 alongwith parallel home display split unit with inbuilt load control switch containing pro vision for TOD and RTC, inbuilt feature to sense the DG mode through PLSI, dual source registration wrt grid as well as DG supply and dynamic load allocation facility from grid and DG, capable to define for tariff slabs, happy hours and holiday definition complete all as specified and directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuite breaker (MCB) of single poles and current carrying capacity 40 Amp, in the MCB DB complete with connection testing all as specified and directed

PREM TRADERS

PANWAR ELECTRICALS

Megh Raj Gehlot

Bhagwati Construction Company

shree technology

AAI NATH ENTERPRISES

SURESH TRADERS