Construction of Sump & Sump Room, Providing and erecting fire fighting system, Detection system and other misc. Work for NCC Jitnagar campus, hostel, staff quarter, Offices, Mess with Fire NOC and Liability, with AMC at NCC Jitnagar Dist. Narmada.

Name of work : Construction of Sump & Sump Room,Providing and erecting fire fighting system,Detection

system and other misc.work for NCC Jitnagar campus,hostel,staff quarter,Offices,Mess with Fire NOC and

Liability,with AMC at NCC Jitnagar Dist.Narmada.

BILL OF QUANTITIES

Item Description of Item (with brief specification and reference to book of Quantity Unit Rate Amount

No. specifications)

1 Supplying, installation, testing and commissioning of electric driven Main Fire Pump 1.00 Nos 400740.27

suitable for automatic operation and consisting of following, complete in all respects,

as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast

iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to

IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed

RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP

protection for enclosure, horizontal foot mounted type with Class-'F' insulation,

conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling

guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation

duly plastered with anti vibration pads.

1.1 2850 lpm at 88 m Hea

2 Supplying, installation, testing and commissioning of electric driven pressurisation 1.00 Nos 112599.53

pump suitable for automatic operation and consisting of following, complete in all

respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump

of cast iron body and bronze impeller with stainless steel shaft, mechanical seal

conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable

for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for

enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS :

325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts

etc. as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads.

3.1 180 lpm at 88 m Head

3 Supplying, installation, testing and commissioning of diesel engine driven main fire 1.00 Nos 606551.56

pump suitable for automatic operation and consisting of following, complete in all

respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal

pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical

seal conforming to IS 1520. Suitable HP, 1500 RPM water cooled with radiator, diesel

engine conforming to relevant IS standard complete with auto starting mechanism,

12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto

m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick

aluminium sheet cladding, residential silencer, instruments and protection as per

standard specification, stop solenoid for auto stop in the event of fault with audio

indications, painted with post office red colour etc. as required. M.S fabricated,

common base plate, coupling, coupling guard, foundation bolts etc. as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads.

2.7 2850 lpm at 88 m Head

4 Fabrication, supply, Insallation testing & commissioning of Electrical control panel of 1.00 Nos 329528.00

cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet,

compartmentalised with hinged lockable doors, dust and vermin proof, powder

coated of approved shade after 7 tank treatment process, cable alley,

interconnection with suitable size copper conductor cable/solid copper strip, having

switchgears and accessories, mountings and internal wiring, earth terminals,

numbering etc. complete in all respect, suitable for main fire pump, pressurisation

pump & diesel pump set complete as per CPWD specification with following in

coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with

enclosure protection class IP 42 as required : 5.1 INCOMING - 400A, 50kA 4 Pole

MCCB, Ics=100% Icu rating Digital Voltmeter 0-500V with selector switch Digital

Ammeter (0-400 A) with selector swtich & CTs etc. LED type RYB phase indicating

lamps, ON, OFF, trip indicating lamps Set of Copper Bus Bar 300A

OUTGOING ( Note : All outgoing feeders for pumps should have digital Ammeter with

selector switches, and LED type ON, OFF, trip indicating lamps)

125 A, 50kA TPN MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable

for 60 HP pump with overload protection, current sensing type single phase

preventor complete with all acceessories and internal wiring required for automatic

operation, selector switch for local/remote, auto/manual/OFF operation. Jockey

63 A, 50kA TPN MCCB, Ics=100% Icu, with suitable HP fully automatic Star/Delta

starter with overload protection, current sensing type single phase preventor

complete with all acceessories and internal wiring required for automatic operation,

selector switch for local/remote, auto/manual/OFF operation.

DIESEL ENGINE CONTROL

Supply for12diesel engineCoolant

V Battery, comprising - Automatic/Manual

,Engine selctor switch & 3 attempts

Oil And Diesel Tank 1.00 SET 29795.00

6 Providing laying,testing & commissioning of 'C' class heavy duty MS Pipe conforming 6.00 Rmt 4924.34

to IS 1239/3589 i/c fittings like elbows, tees,flanges,tapers, nut bolts, gaskets etc. in

ground including welding,excavation & providing cement concrete blocks as

supports,anticorrosive treatment with coaltar/asphalt tape as per IS 10221,refilling

the trench etc.of following sizes complete as required. 200 mm dia

7 Providing laying,testing & commissioning of 'C' class heavy duty MS Pipe conforming 480.00 Rmt 3368.39

to IS 1239/3589 i/c fittings like elbows, tees,flanges,tapers, nut bolts, gaskets etc. in

ground including welding,excavation & providing cement concrete blocks as

supports,anticorrosive treatment with coaltar/asphalt tape as per IS 10221,refilling

the trench etc.of following sizes complete as required.150 mm dia

8 Providing laying,testing & commissioning of 'C' class heavy duty MS Pipe conforming 24.00 Rmt 4837.97

to IS 3589/IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nut

bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support

frame and painting with two or more coats of synthetic enamel paint of required

shade complete as required:200mm dia (wall thickness 6.3 mm)

9 Providing laying,testing & commissioning of 'C' class heavy duty MS Pipe conforming 270.00 Rmt 3165.15

to IS 3589/IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nut

bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support

frame and painting with two or more coats of synthetic enamel paint of required

shade complete as required:150mm

10 Providing laying,testing & commissioning of 'C' class heavy duty MS Pipe conforming 600.00 Rmt 2262.88

to IS 3589/IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nut

bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support

frame and painting with two or more coats of synthetic enamel paint of required

shade complete as required:100 mm dia

11 Providing laying,testing & commissioning of 'C' class heavy duty MS Pipe conforming 350.00 Rmt 1668.91

to IS 3589/IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nut

bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support

frame and painting with two or more coats of synthetic enamel paint of required

shade complete as required:80 mm dia

12 Providing laying,testing & commissioning of 'C' class heavy duty MS Pipe conforming 400.00 Rmt 1134.42

to IS 3589/IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nut

bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support

frame and painting with two or more coats of synthetic enamel paint of required

shade complete as required:50 mm dia

13 Providing laying,testing & commissioning of 'C' class heavy duty MS Pipe conforming 520.00 Rmt 915.29

to IS 3589/IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nut

bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support

frame and painting with two or more coats of synthetic enamel paint of required

shade complete as required:40 mm dia.

14 Providing laying,testing & commissioning of 'C' class heavy duty MS Pipe conforming 450.00 Rmt 658.43

to IS 3589/IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nut

bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support

frame and painting with two or more coats of synthetic enamel paint of required

shade complete as required:25 mm dia.

15 Wrapping & Coating of Underground Pipe. with 4mm damar coat for Pipe Coating 380.00 Rmt 252.50

etc.suitable for pipe size

16 Supplying,fixing,testing & commissioning of double flanged sluice valve of rating PN 3.00 Nos 34831.52

1.6 with non rising spindle,bronze/gun metal seat,ISI marked complete with

nuts,bolts,washers,gaskets and conforming to IS 780 of following sizes as

17 Supplying,fixing,testing & commissioning of double flanged sluice valve of rating PN 2.00 Nos 20157.12

1.6 with non rising spindle,bronze/gun metal seat,ISI marked complete with

nuts,bolts,washers,gaskets and conforming to IS 780 of following sizes as

18 Supplying,fixing,testing & commissioning of double flanged sluice valve of rating PN 2.00 Nos 12965.41

1.6 with non rising spindle,bronze/gun metal seat,ISI marked complete with

nuts,bolts,washers,gaskets and conforming to IS 780 of following sizes as

19 Supplying,fixing,testing & commissioning of double flanged sluice valve of rating PN 2.00 Nos 9471.70

1.6 with non rising spindle,bronze/gun metal seat,ISI marked complete with

nuts,bolts,washers,gaskets and conforming to IS 780 of following sizes as

20 Supplying,fixing,testing & commissioning of butterfly valve of PN 1.6 rating with 6.00 Nos 13467.22

bonze/gunmetal seat duly ISI marked complete with nuts,bolts,washers,gasket

conforming to IS 13095 of following sizes as required:200 mm

21 Supplying,fixing,testing & commissioning of butterfly valve of PN 1.6 rating with 8.00 nos 7934.90

bonze/gunmetal seat duly ISI marked complete with nuts,bolts,washers,gasket

conforming to IS 13095 of following sizes as required:150 mm dia.

22 Supplying,fixing,testing & commissioning of butterfly valve of PN 1.6 rating with 12.00 nos 5904.43

bonze/gunmetal seat duly ISI marked complete with nuts,bolts,washers,gasket

conforming to IS 13095 of following sizes as required:100 mm dia.

23 Supplying,fixing,testing & commissioning of butterfly valve of PN 1.6 rating with 6.00 nos 4412.15

bonze/gunmetal seat duly ISI marked complete with nuts,bolts,washers,gasket

conforming to IS 13095 of following sizes as required:80 mm dia.

24 Supplying,fixing,testing & commissioning of butterfly valve of PN 1.6 rating with 12.00 nos 3350.59

bonze/gunmetal seat duly ISI marked complete with nuts,bolts,washers,gasket

conforming to IS 13095 of following sizes as required:50 mm dia.

25 Providing,installation,testing and commissioning of non return valve of following 3.00 nos 25931.54

sizes conforming to IS:5312 complete with rubber gasket,Gi bolts,nuts,washers etc.as

26 Providing,installation,testing and commissioning of non return valve of following 2.00 nos 15750.74

sizes conforming to IS:5312 complete with rubber gasket,Gi bolts,nuts,washers etc.as

required:150 mm dia.

27 Providing,installation,testing and commissioning of non return valve of following 2.00 nos 9785.64

sizes conforming to IS:5312 complete with rubber gasket,Gi bolts,nuts,washers etc.as

required:100 mm dia.

28 Providing,installation,testing and commissioning of non return valve of following 6.00 nos 5127.87

sizes conforming to IS:5312 complete with rubber gasket,Gi bolts,nuts,washers etc.as

required:50 mm dia.

29 Supply, Installation, Testing and Commissioning of Gun Metal Air Release Valve 6.00 Nos 2373.50

with necessary fittings. Size: 25 mm

30 Supply, Installation, Testing and Commissioning of 100 mm dia Pressure Gauge (for 6.00 Nos 2777.50

all pipes) of range 0 - 15 Kg / cm² conforming to IS - 3624 having bourdon tube of

stainless steel 310 in cast aluminium, stove enameled, black, weather proof

case with outer, screwed aluminium bezel and complete with necessary U-type

stainless steel siphon tube and cock including providing suitably painted angle iron

support to the tube etc.as per required.

31 Providing & fixing of pressure switch in M.S pipe line including connection etc. As 2.00 nos 3383.50

32 Providing, fixing, testing & commissioning of 50sqmm 3.5 Core Alluminium Armoured 600.00 Rmt 398.95

Cable of required size from Main 3 phase connection to Fire Pump House with

Amp MCCB with Cover as required:

33 Providing,installation,testing and commissioning of Y satrainer fabricated out of 1.6 6.00 Nos 15150.00

mm thick stainless steel,grade 304,sheet with 3 mm dia holes with stainless steel

34 Supplying and fixing single headed internal hydrant valve with instantaneous 20.00 Nos 5436.49

Stainless Steel coupling of 63mm dia with cast iron wheel ISI marked conforming to IS

5290 (type-A)with blank cap and chain required:

35 Supplying and fixing Double headed external hydrant valve with instantaneous 20.00 Nos 12625.00

Stainless Steel coupling of 63mm dia with cast iron wheel ISI marked conforming to IS

5290 (type-A)with blank cap and chain required:

36 Supplying & fixing 63mm dia gun metal short branch pipe with 20mm nominal 40.00 Nos 2139.34

internal diameter size nozzle conforming to IS 903 suitable for instantaneous

connection to interconnect hose pipe coupling required:Gun metal

37 Supplying and fixing 63mm dia,15 m long RRL hose pipe with 63mm dia male and 80.00 Nos 4606.40

female couplings duly bound with GI wire,rivets etc. conforming to IS 636 (type-A) as

required:Gunmetal

38 Supply, Installation, Testing and Commissioning of Weather proof Standard Fire 40.00 Nos 3535.00

Hose Cabinet wall mounting type (750 mm x 600 mm x 250 mm deep) having single

or double opening with necessary locking arrangement by allan key suitable for

housing 2 nos. hose pipe, 1no. Branch pipe & nozzle spanner.

39 Supplying and Fixing of fire brigade connection of cast iron body with gun metal male 4.00 set 12375.46

instataneous inlet couplings complete with cap and chain as reqd. for suitable dia MS

pipe connection conforming to IS 904 as required:4 way 150mm dia MS pipe

40 Supplying and Fixing of fire brigade connection of cast iron body with gun metal male 2.00 set 5970.25

instataneous inlet couplings complete with cap and chain as reqd. for suitable dia MS

pipe connection conforming to IS 904 as required:2 way 100mm dia MS Pipe

41 Supply, and fixing First Aid Hose Reel with MS construction spray painted with P.O 40.00 Nos 10691.71

red,conforming to IS 884 complete with the following as required. 20mm nominal

internal dia water hose thermoplastic(textile reinforced) type-2 as per IS

20mm nominal internal dia gun metal globe valve and nozzle. drum and brackets for

fixing the equipment on the wall. Connection from riser with 25mm dia stop gun

metal valve & MS pipe and socket.40mtr.

42 Providing, fixing, testing & commissioning of installation control valve of cast iron 1.00 Nos 42686.67

body, brass/bronze working parts comprising of water motor alarm, bronze seat

clapper, clapper arm and hydraulically driven mechanical gong bell to sound

continuous alarm when the wet riser/sprinkler system activates, pressure gauges,

emergency releases, strainer, pressure switch, cock valve complete with drain valve

and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice

plate, gasket etc of follwing sizes as required : 150 mm Dia

43 Providing, fixing, testing & commissioning of installation control valve of cast iron 1.00 Nos 39852.42

body, brass/bronze working parts comprising of water motor alarm, bronze seat

clapper, clapper arm and hydraulically driven mechanical gong bell to sound

continuous alarm when the wet riser/sprinkler system activates, pressure gauges,

emergency releases, strainer, pressure switch, cock valve complete with drain valve

and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice

plate, gasket etc of follwing sizes as required :100 mm Dia

44 SITC of Intelligent Analog Addressable Type Manual Call Point having Surface or flush 33.00 Nos 9595.00

Option fully complaint to EN54 having Rotary Decade Switches for Addressing from

01-99 complete with Back Box for Mounting Complete as required conforming to

BS5839 Standards and Duly Approved by EN54/LPCB

Make: BOSCH/HONEYWELL/SYSTEM SENSOR/ASES

45 SITC of Addressable Type Loop Powered Hooter Cum Strobe with 32 tone selection, 33.00 Nos 12685.60

features, IP24 housing, Wide operating voltage range, complete with Mounting Base

with required mounting accessories as required conforming to BS5839 Standards and

Duly Approved by EN54/LPCB

Make: BOSCH/HONEYWELL/SYSTEM SENSOR/ASES

46 SITC of Intelligent Analog Addressable Type Photoelectric Type Above Ceiling Smoke 540.00 Nos 4242.00

Detector Complete with Respond Indicator Dual LED, Hard Addressable Having rotary

decade Address switches from 01-99, complete with Mounting Base and required

mounting accessories Complete as required Conforming to BS 5839 Standards and

Duly Approved by EN54/LPCB

Make: BOSCH/HONEYWELL/SYSTEM SENSOR/ASES

47 SITC of 4 Loop Micro processor based 2 wire fault tolerant loop, (each loop accessing 1.00 Nos 388850.00

99 detectors and 99 modules) Networkable Fire Alarm / Detection Control Panel. The

panel shall be able to give location of all fire/fault conditions of addressable units via

the address codes. Further, the panel must be able to automatically switch ON /OFF

respective control module when ever any alarm is triggered. The panel shall have

rectifier, Loop cards, 4x40 – Character LCD alphanumeric display with back-light to

indicate Fire/Fault Signal with address and analog output, external/inbuilt printer to

log all fire or fault events complete in all respects. The panel should be networkable

for up to 99 panels. The Panel Shall be Sheet Steel Painted, sealed to IP30. The Panel

Shall have 20 Zones with Individual LED Indicators, expandable to 200 LED Indicators.

The Panel Shall have 3 Serial Ports. The panel shall have provision to integrate with

PA System and shall have provision to connect to Building Management system

through Modbus Card. The panel shall have a 4 programmable sounder outputs, and

open / short circuit monitoring. The panel shall have a built in power supply and

battery charger, which should be capable to charge maintenance free 24 AH, 2 x

volt SMF Lead acid batteries capable of running for a minimum of 24 hours with

battery charger complete as required. and conforming to BS5839 Standards and Duly

Approved by EN54/LPCB as per specifications.

Make: BOSCH/HONEYWELL/SYSTEM SENSOR/ASES

48 Supplying and laying of 2x1.5 sqmm fire alarm armoured cable,600/1000V rated with 3100.00 Rmt 152.89

annealed copper conductor having XLPE insulation,steel wire armouring &FRLS outer

sheath complete as required.

49 FIRE DETECTION SYSTEMS ,Supply, installation, testing and commissioning of Below 15.00 Nos 3832.95

False Ceilling Addressable ideal optical smoke detector for detecting visible smoke

particles with Mounting Base Item as per drawing and specifications, as approved by

electrical engineer incharg

50 SITC of Active Repeater Panel facilitate to Silence, Mute, Reset, Accept, Evacuate and 1.00 Nos 126954.98

Test Controls along with other I/O peripheral devices and the external printer

further enhance the flexibility and functionality of the fire alarm control panel. The

Repeater Panel shall have 80 character Backlit adjustable alphanumeric LCD display

and the 7 LED status indicators. The Repeater Panel shall have “Access Enable” key-

switch and with required power battery backed up power supply. Duly Approved bt

EN54/LPCB as per specifications.

Make: BOSCH/HONEYWELL/SYSTEM SENSOR/ASES

51 Providing,fixing,testing & commissioning of 15mm dia quartzoid bulb type sprinklers 500.00 Nos 462.22

of rating 68 degree centigrade with required accessories:Pendent sprinkler

52 Providing,fixing,testing & commissioning of 15mm dia quartzoid bulb type sprinklers 20.00 Nos 546.68

of rating 68 degree centigrade with required accessories:Horizontal side wall

53 Providing,fixing,testing & commissioning of 15mm dia quartzoid bulb type sprinklers 20.00 Nos 1270.50

of rating 68 degree centigrade with required accessories:Concealed sprinkler

54 Providing, fixing photo luminescent Signage's as per IS standard in Block / Small 9500.00 Sq.inch 9.09

Letters on rigid sheet with necessary wall or Ceiling fittings as Specified Sizes:

For Fire Extinguisher,exit,do not to do,etc.

55 Supply, installation, testing and commissioning of Stainless steel Ball Valve. a) 25mm 48.00 Nos 1212.00

56 Providing Core Cutting for beam & Slab up to 25 mm to 100 mm dia directed by 130.00 Nos 858.50

engineer in-charge.

57 Supplying, Installing, Testing & Commissioning of M.S. structural steel support. 2500.00 kg 90.90

58 Suppy, Installing, Testing and Commissioning of C.I. Heavy duty foot valve with 3.00 Nos 16665.00

flangs, Nut bolts, Gaskets etc. with necessary complete accessories.150mm

59 Suppy, Installing, Testing and Commissioning of C.I. Heavy duty foot valve with 3.00 Nos 12625.00

flangs, Nut bolts, Gaskets etc. with necessary complete accessories.100mm

60 3 Layer PVC Storage Tank 10000 ltr. Installation With all accessories like 2.00 Nos 106050.00

M.T,L.T,Band,Clamp,Solution And Plumbing charges including as per MR

61 Fire Blanket 10.00 Nos 2222.00

62 Supplying FIRE bucket round bottom of 9 liters capacity made out of 24 gauge G.I 48.00 Nos 1025.15

Sheet with extra handle at bottom duly painted white inside and Red out side with

FIRE mark. Filled with dry-sand and kept on existing stand provided or hung on wall

63 Supplying and erecting floor mounting Stand for keeping four nos. of FIRE buckets 12.00 Nos 5807.50

comprising 1500 mm in length, 900 mm height frame made out of 30mm x 30 mm x

mm angle iron with cross supports legs, welded with 4 hooks and duly painted with

one coat of primer and two coats of approved enamel P O red paint.

64 Submitting the application to obtain Fire Plan Approval and After Completion of 1.00 Nos 267650.00

Work Obtain Final Fire NOC for 3 Year

65 Supply, installation, testing & commissioning of Priming tank, HDPE type, 1000 litres, 1.00 Nos 53530.00

with necessary piping 100 mm size, G.I pipe for priming the pumps, pipe of with

butterfly valves for isolation, Water Filling to priming tank by piping min. 50 mm size,

with all complete.

66 Pay Legal Fees to Concern Authority for Obtaining Plan Approval and Final NOC 6600.00 SQ.mtr 15.15

67 Excavation for foundation up to 1.50 MT depth including sorting out and stacking of 75.00 Cum 160.89

useful materials and disposing the excavated stuff up to 50 mt lead B) Dense or Hard

68 Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out 75.00 Cum 174.56

and stacking of useful materials and disposing off the excavated stuff upto

Meter lead. B) Dense or Hard soil

69 Excavation for foundation for depth from 3.0 m to 5.0 m including sorting out 25.00 Cum 333.38

and stacking of useful materials and disposing off the excavated stuff upto

Meter lead.(D) Soft rock not requiring Blasting

70 Providing and laying controlled cement concrete M.150 and curing complete 8.00 Cum 3792.55

including the cost of formwork and excluding reinforcement for reinforced concrete

work in (A) Foundations and plinth pcc

71 Providing and laying controlled cement concrete M.250 and curing complete 15.00 Cum 4460.16

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in(A) Foundations, footings, and Mass concrete. footing

72 Providing and laying controlled cement concrete M.200 and curing complete 14.00 Cum 6473.09

including the cost of formwork but excluding the cost of reinforcement for reinforced

concrete work in (C) Ground floor Slab

73 Providing and laying controlled cement concrete M-250 and curing complete 3.00 Cum 7841.64

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in (d) columns Up to Plinth level.

74 Providing and laying controlled cement concrete M-200 and curing complete 4.00 Cum 7780.03

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in Columns, pillars posts and struts Ground FLOOR

75 Providing and laying controlled cement concrete M-200 and curing complete 18.00 Cum 5822.65

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in Ground & Plinth BEAMS

76 Providing and laying controlled cement concrete M.200 and curing complete 3.00 Cmt 6176.15

including the cost of form work but excluding the cost of reinforcement for

reinforced concrete work in (C) Ground floor Beams,

77 Brick work using common burnt clay building bricks having crushing strength not less 20.00 Cmt 4279.98

than 35 Kg./Sq.Cm. in foundation and plinth in Cement Mortar 1:6 (1- Cement : 6 -

fine sand) (B) Conventional.

78 Brick Work using Common Burnt Clay Building Bricks having crushing strength not 21.00 Cmt 4568.23

less than 35 Kg/sm. in super structure Above plinth level up to floor two level in

cement mortar (1:6) ( 1 cement : 6 fine sand) (Conventional) For All Floors

79 Providing and laying controlled cement concrete M-200 and curing etc. complete 17.00 Cmt 8846.59

including the cost of form work and excluding the cost of reinforcement etc.

complete in RCC wall up to floor two level for Below plinth

80 Providing cement vata (10cm x 10cm size) quarter round in cement mortar 1:1 29.00 Rmt 24.28

including neat cement finishing watering etc. Complete

81 Providing 20 mm thick double coat mala cement plaster on interior brick / concrete 183.00 Sqm 353.50

work for plastering comprising of base coat of 12 mm thick cement plaster in cement

mortar (1 Cement : 4 coarse sand) in rough finishing and 8 mm thick top coat of

cement mortar 1:2 (1 Cement : 2 Coarse sand) finished with trovel including

scaffolding curing etc. complete. For Ground floor

82 Providing Water proofing Treatment on Sunk Slab including cement concrete flooring 114.00 Sqm 373.70

1:2:4 (1-cement : 2-coarse sand : 4-graded stone aggregate 20mm nominal size) laid

in one layer and finished with a floating coat of neat cement average 50mm thick to

Prepare slope including water proofing chemical etc. Complete for Sunk Slab All

83 Providing and laying Ceramic tiles 6mm thick in skrting risers of steps and dedo on 114.00 Sqm 1070.50

10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white

cement slurry (upto 10 ton)

84 Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having weight not less 1.00 Nos. 958.17

85 Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding 10770.00 Kg 77.29

and placing in position complete up to All floor Level

86 Providing & erecting open well horizontal mono block pump set with cast iron body, 2.00 Nos 36107.50

complete for three phase submersible motor having [H]For 15 H.P,3 phase open well

horizontal mono block pump set suitable for 1600 LPM to 1025 LPM @ 33 to 42 MTR

head suitable for 65/80 mm dia delivery pipe

87 20 mm thick Sand faced Gutka cement plaster with 1x1 cm grooves as suggested by 96.00 Sqmt 353.50

this office consisting of 12 mm thick backing coat of C.M. 1:3 ( 1 cement : 3 coarse

sand ) and 8 mm thick finishing coat of C.M. 1:1 ( 1 cement : 1 coarse sand) for all

heights as directed etc. complete.

88 Providing 10 mm. Thick Mala cement plaster in single coat for plastering on ceiling 79.00 Sqmt 176.75

and soffits of stairs and finished even and smooth in : (I) Cement mortar 1:3 (1

cement : 4 sand) including Mala troveled finish etc. complete comp.For .Ground

89 P & L 60x60 cm Machin cut Mirror polished Blue Kota Stone slab 25 mm thick flooring 38.00 Sqmt 1019.39

over 20 mm (average)thick base of cement mortar 1:6 (1-cement 6-coarse sand) or

L.M 1:1.5 (1 Lime putty : 1.5 coarse sand laid over and jointed with grey cement

slurry mixed with pigment to match the shade of slab including rubbing and polishing

90 P & L 60x60 cm Machin cut Mirror polished Blue Kota Stone slab 25 mm thick in riser 2.00 Sqmt 1205.60

of steps,skirting dedo and pillars laid on 10 mm thick cement mortar 1:3 (1-cement 3-

coarse sand) and jointed with grey cement slurry mixed with pigment to match the

shade of slab including rubbing and polishing etc.complete

91 Applying two coats of Birla (white cement based) or Asian (acrylic lappy (putty)) or 119.00 Sqmt 40.59

equivalent and two coats of primer of approved brand and manufacture on new wall

surface to give an even shade including thoroughly brushing the surface free from

mortar dropping and other foreign matter and sand papered smooth.

92 Distempeing (Two coats) with oil bound distemper of approved brand and 176.00 Sqmt 77.30

manufacture and Washable of required shade on wall surfaces to give an even

shade, over and including a priming coat with distemper primer of approved brand

and manufacture after thoroughly brushing the surface free from mortar dropping

and other foreign matter and also including preparing the surface even and sand

papered smooth.

93 Distempeing (Two coats) with oil bound distemper of approved brand and 75.00 Sqmt 85.85

manufacture and Washable of required shade on Celling and sloping roof to give an

even shade, over and including a priming coat with distemper primer of approved

brand and manufacture after thoroughly brushing the surface free from mortar

dropping and other foreign matter and also including preparing the surface even and

sand papered smooth.

94 Wall painting two coats with weather proof acralic emulsion APEX type paint of 93.00 Sqmt 122.14

approved brand & manufacture and of required shade on exterior wall surface to

give an even shade over and including a primery coat with alkaly resistance primer

of approved brand after throughly brushing surface to remove all dirt and remains

of loose powdered materials etc comp. for all height.

95 Providing and fixing rolling shutters of approved make made of 80 mm wide M.S 9.00 Sqmt 2796.59

laths inter-locked together through heir entire length and jointed together at the

ends by end locks mounted on specially designed pipe shaft with bracket

plates,guide channels and arrangement for inside and outside locking with push-pull

operation including the cost of hood cover and sprig etc.complete(A) Shutters having

width Above 3.5M

96 Providing and fixing window having extruded aluminum Colour anodized section 4.00 Sqmt 2362.39

frame main outer size 95mm x 24mm x 1.17mm (of Jindal Section no:2459 @ wt.of

0.738 Kg/mt) horizontal two track member size size 92mm x 31.75mm x 1.50mm (of

Jindal Section no:8933,@ Wt. 1.06 Kg/mt), vertical member of size size 92mm x

31.75mm x 1.50mm (of Jindal Section no:8933,@ Wt. 1.06 Kg/mt)with sliding

shutters of horizontal member size 40mm x 18mm x 1.29mm (of Jindal Section

no:8949 @ wt.of 0.456Kg/mt), vertical member of size 40mm x 18mm x 1.29mm (of

Jindal Section no:8947 @ wt.of 0.456Kg/mt/ Section 8948, @ Wt. 0.457 Kg/mt) with

mm thick transparent bronze colour tinted float glass with powder coated aluminum

fittings and fixtures and transparent silicon sealant glass fixing to frame as per details

etc complete for W2&W3

97 Providing and laying controlled cement concrete M-200 and curing etc. complete 1.00 Cmt 6299.37

including the cost of form work and reinforcement for reinforced concrete work in

(c) Chhajja for G floor

98 Providing and laying controlled cement concrete M-200 and curing etc. complete 1.00 Cmt 7430.57

including the cost of form work and reinforcement for reinforced concrete work in

(c) Lintel for Ground floor

99 Providing and laying water proofing treatment with broken china mosaic flooring 44.00 Sqm 1164.53

over 50mm thick cement concrete flooring 1:2:4 level in one layer & finished with a

floating coat & net cement using 12mm to 20mm of broken piece of ceramic glazed

tiles (or more colour directed ) to be laied over cement mortar bedding of cm 1 : 3 (1

cement 3 sand ) to blain or slope and to be tempered to bring mortar ceramic up to

surface with using white cement and colour pigment including rounding of junction

extending them up to 15cm along the wall and caring with bends any patten or

design on per drawing and clennig by using oxalic acid etc. Completed

100 Providinfg and fixing Safty grills of required pattern for windows/ Door using 90.00 Kg 116.91

necessary M.S angle/ M.S pipe, M.S flats and other structural steel at required

spacing including cutting, welding and fabriction etc. including one coat of primer of

approved quality and two coats of oil painting as per detail drawing etc complete.

101 Providing and fixing Mirrar polished 18 mm thick Green Marble stone with full round 12.00 Sqm 1730.13

edge and polished of approved quality in clading on sill and around the doors/

windows/ ventilation with 20 mm thick cement motor CM (1:3) and fixing with

cement slurry & adhesive including moulding of exposed edges as directed by

engineering in charge etc. complete.

Rs. In words :- One crore seventy six lakh ninty six thousand eight hundred seventy one and one paisa only

I/We am/are willing to carry out the work at… % above/below percent(Should be written in figures and words) of the estimated rate mentioned

above. Amount of my /our tender works out as under.

* Estimated Amount * Estimated Amount

put to tender put to tender

Deduct :…………% Below Add :………%Above

In Words …………………………………… In Words………………………………

* (Please strike out whichever is not applicable).

1 The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for which no extra

payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 GST and Income tax TDS will be deducted at a source while making payments of bills

4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017 Cement Consumption/16/C

Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change as per actual mix design the cost of difference of

cement consumption have been deducted from the rate of original item at the rate of input rate mentioned in all the tender.

5 The amount of dismentalled credit materials at Rs. 0 shall be deducted from first R.A. Bill.

Dy. Executive Engineer Executive Engineer

Rajpipla(R&B) sub Division Rajpipla (R&B) Division

Rajpipla Rajpipla