PROVN OF COVER SHED FOR BLDG NO P-50 OF CERTAIN MIL UNIT AND PROVN OF INDUSTRIAL ROOF VENTILATOR AT CERTAIN MIL UNIT TELEPARA-1 AT BINNAGURI UNDER GE (S) BINNAGURI

Amount

Excavation in post holes (or similar holes) each n.exc 0.5 Cum getting out and removing surplus soil to a distance n exc 50m and making good surfaces in soft/loose soil all as specified

Surface excavation n.exc. 30cm deep and averaging 15cm deep and getting out in hard/dense soil all as specified

M & L for cement concrete type C-2 1:3:6 (using 40mm graded aggregate) in foundation filling mass concrete all as specified

S&F for mild steel tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St-240 Complete all as specified

M&L for MS flat iron bent to shape, holes drilled etc complete as in wind ties etc complete all as specifed

Supply and fix 0.50mm thick prepainted galvalume polyester coated (SMP coating) coloured metal roofing sheet trapezoidal profile having tensile strength 550Mpa as in roof covering fixed with self drilling screws with EPDM washer etc complete all as specified.

Ditto--- all as per item No 06.00 above but as in eaves board fixed with selp tapping screw as specified.

M&L for MS plate of any size & thickness, holes drilled or without drilled etc complete all as specified

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or girth all as specified

M&L for Preparation of new steel surfaces of any description n.exc.10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxideprimer all as specified

M&L for providing cement concrete type B-0 (1:2:4)(using 12.5 mm size graded aggregate) as in coping set incl weathering, slightly rounded or chamfered angles & thickness all as specified

M&L for 100 mm thick cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in path /steps laid with and incl use and waste of form work and finishing the surface even and rough to receive the topping layer or tiling complete all as specified

M & L for hard core of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified

M & L 80 mm thick M-40 grade factory made vibratory compacted cement concrete rubber moulded, interlocking paver block any shape and size confiroming to IS 15658-2006 with grey cement and pigment as approved laid over and incl 50 mm thick consolidated sand cushion and joints filled with sand complete all as specified

M&L for rendering 20 mm thick in two layer, first layer shall be of 10 mm thick CM 1:4 and second layer of finishing coat shall be 10 mm thick in CM 1:4 mixed with WPC all as per manufracture's specification on brick work or concrete surfaces of wall and finished even and fair complete all as specified Note-WPC shall be measured and paid seperately.

Supply only integral water proofing compound all as specified

M&L 75mm thick PCC (1:3:6) type C2 as in plinth protection/footpath using 40mm graded stone aggregate finishing cement concrete surface even & smooth using extra cement including bitumen filling in two panel etc complete all as specified

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in soft/ loose soil all as specified

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with soils all as specified

Removing Excavated soils exceeding 250 M but not exceeding 500 M and depositing where all as specified.

M&L for brickwork with burnt fly ash old size bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks complete.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified

M&L for point wiring complete with 1.5 Sqmm multistranded copper conductor single core PVC insulated, IS 694 unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less than 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sunken terminal box made out of GI sheet steel not less than 1.22 mm thick for boxes duly painted with anticorrosive paint, concealed in walls with bakelite/plastic laminated sheet top cover fixed with cadmium plated iron screws for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sunken for boxes and making good to the disturbed surface of wall/floor and matching with specifications all as specified where concealing of conduit is not feasible i.e on surface of roof/ ceiling etc, conduit shall be fixed on surface with necessary saddles at no extra cost complete for the following :-

One light point controlled by one way switch 5/6 amps.

S&F switch piano flush type 5/6 amps single pole one way complete all as specified

S&F ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified

Supply and fix LED High bay light 50 Watt ,IP66 protection with PDC integrated high efficiency electronic driver and surge suppressor of 4KV or more, luminaire efficiency not less than 120 lumens/watt, power factor not less than 0.90, CRI 80, THD 10%, operating range - 140 to 270 V, 50 Hz suitable for ceiling mountand in wide beam optics, system efficacy 120 lm/W complete including fixing arrangement all as specified

S & F LED street light fittins 30 Watt or next higher size upto 35 watt in aluminium PDC housing, toughned glass cover with IP66 protection integrated high efficiency electronic driver and surge suppressor of 4KV or more, luminaire efficiency not less than 120 lumens/watt, power factor not less than 0.90, CRI 80, THD 10%, operating range - 140 to 270 V, 50 Hz complete all as spedified

M&L for street light bracket made out of GI pipe light grade 25 mm dia 1.2 mtr length bent to shape and reduced to required size at top upto 1.2 mtr length by cutting, welding and well finishing including MS clamp of flat iron of size 25 x 5 mm suitable length 2 Nos complete with drilling hole, fixing with runts bolts and washers including painted with two coats aluminium paint over a coat of red oxide primer.

S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), double door, single pole & neutral with minimum 100 Amps rated bus bar minimum IP-43 protection level protection suitable for fixing MCB"S/lsolators complete all as specified

S&F MCB, Single pole & neutral 32 amps, 240 volts, ‘C’ curve, 10 KA all complete all as specified

S&F MCB, Single pole, 5 to 32 amps, 240 volts, ‘B’ curve, 10 KA all complete all as specified

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete all as specified

M & L Sub main wiring surface type with two run single core cable PVC insulated cable with 4.0 Sqmm (Nominal area) multi stranded copper conductor FRLS cable 1100 volts gde incl earth continuity conductor using PVC insulated cable of stranded copper conductor of size 4.0 Sqmm connected to common earth dolly and drawing in and including 25mm PVC medium grade conduit pipe and fittings, making good the disturbed surfaces complete.(NOTE : Two run of submain wiring cable alongwith one run of earth wire and steel conduit shall be measured as one length. .

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core all fixing and connecting accessories such as cable lugs, cable glands, nut, bolts, complete all as specified

M&L for sand cushioning in cable trenches over & under the cable, with river washed coarse sand, as per standard practice with proper compaction complete all as specified. (Punned thickness 18 cm shall be considered for payment as per para 19.75 of SSR Part-I)

Supply and laying for brick protection for protection of cable over sand cushioning cables inside the trench by using common brunt clay building bricks sub-class “B” old size brick and flat and width wise along the axis of the trench complete all as specified

Supply and fixing 40 mm dia GI tubing medium grade ISI marked laid in trenches / laid under floor for protection of cable including all fittings such as elbow, bends, etc and short length complete all as specified

Supply and install Turbo Ventilator 24 Inch of Stainless Steel fins over CGI roof with 42 nos 4 mm thick SS 304 grade fins, self lubricated dual ball bearing, SS shaft, SS Bottom throat & top with all necessary rivets or screws as required, Polycarbonate base plate UV grade 2 mm thick designed according to roof profile of size 1.7 m x 1 m complete all as specified

Material & labour for cutting of existing GI roof sheet as per site requirement for fixing Turbo ventilator of size 24 Inches including necessary minor items and T&P required for fixing roof ventilator with all necessary fixing arrangement and making good to disturbed roof all as to match with existing and ceiling to be make complete water leak proof at joints complete all as specified

M/S RATNESH KUMAR SINGH (BID ID -3476748)

M/S SHIVNATH SINGH (BID ID -3476728)

AKASH PRASAD GUPTA (BID ID -3481535)