CA NO GE(N)AMB-23/2022-23 REPAIR TO JOINERY, PLUMBING, SANITARY, PLASTERING AND OTHER CONNECTED BUILDING REPAIR WORK IN MD-I AREA OF AGE B/R-II (NORTH) UNDER GE (N) AMBALA CANTT

Amount

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed by the Engr-in-charge.

M&L brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed by the Engineer-in-Charge.

M&L rendering 15mm thick in cement mortar 1:6 on any faces of brick work or concrete wall surfaces and finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in charge.

M&L rendering 15 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:4 and finished even and fair without using extra cement but using water proofing compound @ 2% by weight of cement or as per manufacturer's instructions complete all as specified and as directed by the Engineer-in-Charge. (water proofing compound shall be measured and paid for separatally)

M&L rendering 5 mm thick on fair faces of brick work or concrete ceiling or chajjas surfaces in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L rough cast plaster complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar 1:4 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg. which is generally of size between 6 to 12 mm depending on texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer-in-Charge.

Cutting chases to brick walls, pinning in making good to facing where required and pointing in CM 1:3 to edges of landing , steps , cills , sunshades, shelves , lintel etc. and cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth complete all as specified and as directed by the Engineer-in-Charge.

M & L preparing new plastered/unplastered surfaces and applying two coats of cement base paint on surfaces of walls, chajjas, roof projection complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of newly plastered/ unplastered surfaces of walls and applying two coats of oil bound distemper with painting roller over and including a coat of alkali resistent primer complete all as specified and as directed by the Engineer-in-Charge.

M & L preparing new plastered/unplastered ceiling surfaces and applying two coats of white lime wash on surfaces of ceiling complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair mild steel powder coated wooden finish curtain rod 25mm dia having wall thickness1.6mm fixed with and including decorative brackets ,stop roller and glass at the end etc complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed by the Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer-in-Charge

M & L galvanised iron tubing 15mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

M & L galvanised iron tubing 20 mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by the Engineer-in-Charge.

S&F bib taps 15mm bore fancy type brass chromium plated capstan head with long body screwed down for iron pipe and fixed as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F fancy type pillar tap of 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

M & L 75mm bore PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement as in repair complete all as specified and as directed by the Engineer-in-Charge

S & F 15mm bore cast copper alloy fancy type chromium plated stop valves, screwed down, high pressure with capstan head, scrwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges as in repair complete all as specified and as directed by the Engineer-in-Charge

S & F 15mm bore cast copper alloy angular type chromium plated stop valves, screwed down, high pressure with capstan head screwed both ends for iron pipe or for unions as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F vitreous china wash hand basin white, flat back of size 550mmx400mm with pedestal fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of waste fitting etc as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F vitreous china squatting pan, Orissa pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

S & F 10 ltr PVC valveless syphonic action type flushing cistern with brackets, flush pipe etc complete including inlet ball valve float and handle including brackets, of approved make including all connections & flush pipes for WC as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern) including plastic water closet seat white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinges device and brass chromium plated Jet spray with PVC pipe with complete accessories as in repair complete all as specified and as directed by the Engineer-in-Charge.

S&F galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tack or galvanised wire staple complete all as specified and as directed by the Engineer-in-Charge.

S & F sinks with drainage board made out of stainless steel 1mm thick sheet for kitchen with plugs, waste pipe, brass chromium plated coupling and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm with bowl size 405mm x 354mm x 203mm complete all as specified and as directed by the Engineer-in-Charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

M&L Non Skid coloured ceramic tiles joint free premium/1st quality 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and inculding 15mm thick screed bed in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge.

M&L Non Skid coloured ceramic tiles joint free premium/1st quality of same description as of floor tiles in serial item No.32 above but 150mm height as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M&L glazed ceramic coloured tiles joint free premium/1st quality in vertical surfaces/skirtings/dados of size 300x600 x7mm/ 450x 350x7mm thick or nearest size, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

M & L 25mm thick plain cement concrete 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in sub base, finished even and fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M & L 16 to 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4 incl rounding of front edge complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames area exceeding 1.50 Square meter and not exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engineer-in-Charge

Taking down chowkats or frames area not exceeding 1.50 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed by the Engineer-in-Charge

Taking down shutters of any description area exc 1.00 sqm and not exc 2.00 Sqm each and removing the same from site complete all as specified and as directed by the Engineer-in-Charge

Resecuring or easing & adjusting shutters of any description not exc 1 Sqm each, without taking down shutters complete all as specified and as directed by the Engineer-in-Charge

Resecuring or easing & adjusting shutters of any description exc 1 sqm and not exc 2 Sqm each, without taking down shutters complete all as specified and as directed by the Engineer-in-Charge

Taking down carefully steel door shutter exceeding area 1.00 sqm but not exceeding 2.00 Sqm including cutting, welding and adjusting as per opening and refiixng the same at same location complete all as specified and as directed by the Engineer-in-Charge (new angle iron etc shall be measuared and paid for separately)

M&L factory made 2nd class hard wood 35 mm thick plain framed panelled shutter( two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on boths face . The size of rail and style as per IS:1003 (Part-1) kiln seasoned and chemically pressure treated complete all as specified and as directed by the Engineer-in-Charge.

M&L factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters,open rebated and prepared to receive glass , gauze etc. (without sash bars) ,edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood shall be seasoned and chemically pressure treated) complete all as specified and as directed by the Engineer-in-Charge.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm prelam PVC sheet on single side used instead of plain colour PVC sheet reinforced with MS square tube, edges will be painted to match with prelam sheet and fixed in opening complete all as specified and as directed by the Engineer-in-Charge.

S&F factory made solid PVC moulded door shutters with partical board core 28 to 30 mm thick (styles) with 2, 4, or 6 raised panel design with 2 mm thick prelaminated moulded PVC sheet on the front face and 2mm thick plain colour PVC sheet on back face fixing in frame at site as per specification and drawing complete all as specified and as directed by the Engineer-in-Charge.

M&L rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe-410-W (Gde E-250) quality 'A' complete all as specified and as directed by the Engineer-in-Charge.

M & L PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in holdfasts complete all as specified and as directed by the Engineer-in-Charge.

S&F double shutter steel window box type ERW hollow P section comprising of glazed/gauged skeleton shutter fabricated from following sections :- (a) ERW hollow P section of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter ). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces . (b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leaf of T – section 20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf . (c) Vertical mullion shall be ERW hollow T -section of size 60 x 25 mm made from 1.25 mm thick MS sheet (d) The above steel window shall be deemed to include the following accessories/ fittings : i) Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt stove enamelled 150mm long- 2 Nos per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 No per leaf vi) Pintal hinges 12 x 75 mm - 2 Nos each leaf vii) 10mm square Guard bar @ 10 cm c/c welded to frame . (viii) Two coat of Synthetic enamel paint over one coat of red oxide primer. (ix) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in gauzed skelton shutter of window with flat iron 15 x 03 mm with steel screws . (x) 3mm thick sheet glass, ordinary quality and with oil putty in square n. exc 0.5 sqm in each pane fixed in glass shutter of window. (xi) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed. Notes : (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessoriries as mentioned above. (iii) The window upto 1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable. The window more than 1.00 metre width shall have two openable leaves on both outer side for gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type.

S&F box type using ERW hollow 'P' section ventilators fixed type with glazing bar including MS grills of square bar 10mm dia @ 100 c/c complete with glazing bars dovetailed or welded, including two coat of synthetic enamel ordinary tint paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair mild steel door shutter two leaves with frame of 20 gauge MS sheet (all around) and leaves of 21 gauge MS Sheet ( all as per Godraj Pettern) with three way locking arrangement with brass lock with duplicate key and CP handle including two coats of spray painting over a coat or red oxide primer complete fixed in existing cupboard fixed with necessary nuts, bolts including embedded in PCC 1:2:4 (area of opening shall be measured) complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair stainless steel conduit pipe 20mm dia having wall thickness 1.6mm with 2 Nos stainless steel brackets at both end fixed with stainless steel screws , complete all as specified and as directed by the Engineer-in-Charge

M & L Plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads, using 2nd class hard wood clean sawn sectional area exc 13 sqcm and not exc 25 sqcm complete all as specified and as directed by the Engineer-in-Charge

S & F 75mm long brass handles, cast type, polished bright complete all as specified and as directed by the Engineer-in-Charge.

S & F brass Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of boarding of any type/size as in cup boards/ wardrobes including hardware complete all as specified and as directed by the Engineer-in-Charge.

S&F 18mm thick lead free PVC celuka ply ( minimum density 600 Kg/ Cum) of both side plain of approved colour other than white colour fixed with stainless steel screws and solvent cement / adhesive to make kitchen / bed rooms cabinet sides, top and bottom and shelves inside the cabinets complete all as per manufacturer's specifications/ instructions complete all as specified and as directed by the Engr-in-charge.

S & F Continuous (piano) hinges, width of flaps 30mm mild steel, bright finish or electro galvanised complete all as specified and as directed by the Engineer-in-Charge.

S & F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and as directed by the Engineer-in-Charge.

S&F magnet catcher fixed in cabnet shutter (one portion) and wooden frame (other portion) with screw complete all as specified and as directed by the Engineer-in-Charge.

S&F 150 mm long aluminium handle cast type anodised complete all as specified and as directed by the Engineer-in-Charge.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 250mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter complete all as specified and as directed by the Engineer-in-Charge.

S & F butt hinges 100mm long of stainless steel medium weight complete all as specified and as directed by the Engineer-in-Charge.

S&F mild steel 150 mm ordinary rat tail rod pattern springs including roller and roller plate etc complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by the Engineer-in-Charge.

M&L preparation of new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

S & F 32 mm bore Low density polyethylene pipes (LDPE)of pressure rating 6kgf/Sq cm of standard length suitable for WHB and sink as in repair complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete in existing sunken floor etc and removal of the same to a distance exceeding 250 mtr and not exceeding 500 mtr, depostied where directed complete all as specified and as directed by the Engineer-in-Charge.

M&L PCC 1:5:10 type E-2, using 40 mm graded crushed stone aggregate as in filling in sunken floor, rounded or chamfered on edges complete all as specified.as directed by the Engineer-in-Charge.

M&L providing sunken floor water proofing treatment comprising of the following :- (a) Scrapping the surface with wire brush and cleaning with water and allow to dry. (b) Applying cement slurry @ 1.2 kg/sqm duly mixed with water proofing compound @ 2% by weight of cement or as per manufacturer's instructions. (c) 15 mm thick cement plaster (1:3) mixed with water proofing compound @ 2% by weight of cement or as per manufacturer instruction ( the corners will be made round in concave shape) and finished even and fair without using extra cement. (d) Applying cement slurry @ 1.2 kg/sqm duly mixed with water proofing compound @ 2% by weight of cement or as per manufacturer's instruction. (e) Applying one coat of hot blown bitumen grade 85/25 confirming to IS-702 @1.20kg/sqm (f) Providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt using butane gas torch and ceiling all joints. (g) Applying one coat of hot blown bitumen grade 85/25 confirming to IS-702 @1.20kg/sqm.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified & directed by the Engr-in-Charge.

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed by the Engineer-in-Charge

S & F 110mm bore PVC (SWR) bends of any radius with access doors complete all as specified and as directed by the Engineer-in-Charge.

S & F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed by the Engineer-in-Charge

S & F 75mm bore PVC (SWR) bends of any radius with access doors complete all as specified and as directed by the Engineer-in-Charge.

Dismantling water tanks of capacity exc. 250 ltr and not exc. 500 ltrs and removing from site complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing water storage tank, 500 ltr capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore, complete all as specified and as directed by the Engineer-in-Charge.

S & F 20 mm dia ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply only water proofing compound complete all as specified and as directed by the Engr-in-charge.

S & F as in repair PVC tank lid/cover suitable for capacity 500 ltr and upto and including 1000 ltrs with and including locking arrangments such as nuts, bolts etc complete all as specified and as directed by the Engineer-in-Charge.

S & F 15 mm bore Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe as in repair complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work including cutting of steel reinforcement as required to facilitate demolition and removal the rubbish/ demolished material outside defence land, complete all as specified and directed.

S&F galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed with tinned tack or galvanised wire staple as in repair complete all as specified and as directed by the Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds and steel window frame glazed with putty or fixed with beads complete all as specified and as directed by the Engineer-in-Charge.

M & L sheet glass 3.0mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and as directed by the Engineer-in-Charge

M & L figured sheet glass 3.0mm thick , pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and as directed by the Engineer-in-Charge

S & F 2nd class hardwood small fittings such as brackets of any type, latch and hinge blocks, shapped door and window stops and the like, including all necessary labours, articles n exc 200 cu. cm each including 50mm long stainless steel butt hinges complete all as specified and as directed by the Engineer-in-Charge.

S&F as in repair grating doom 100mm dia of PTMT (min weight 25gms) complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair waste fittings, 32 mm dia brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed by the Engineer-in-Charge.

S & F as in repair waste fittings, 38 mm dia brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed by the Engineer-in-Charge.

M&L for running welding in repairs thickness of metal to be welded not exc 6mm complete all as specified and directed by Engr-in-charge.

M&L cleaning and removing all scale and dirt etc from PVC/RCC tanks and mouths of circulating pipe of capacity exceeding 250 litre and upto and including 1000 litre & writing on the tank with synthetic enamel paint not less than 70mm long and 2mm wide of words in shape like cleaned on : 15.06.2018 complete all as specified and as directed by the Engineer-in-Charge. NOTE :- unit rate shall be included to make small fittings such as elbow, socket, reducer, tee, union etc .

Excavation in trenches, not exc 1.5 m wide and not exc 1.5 m in depth for foundation etc or for shafts, wells, manholes etc. not exc 10 sqm on plan and not exc 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed by the Engineer-in-Charge.

M & L concrete bed to drain pipes of 110mm bore, including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate complete all as specified and as directed by the Engineer-in-Charge

S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and as directed by the Engineer-in-Charge.

Returning, filling in, including spreading, levlling ,watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed by the Engineer-in-Charge.

Removing surplus excavated material to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

M & L providing PCC precast 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, precast cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weathering, throating etc complete with joints to match, complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for including removal the rubbish/ demolished material outside defence land, complete all as specified and directed.

M & L 40mm thick plain cement concrete 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in floor and surface finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

S&F Glass dividing strips, 38 mm wide and 3 mm thick inserted in position to confirm to design complete all as spd and directed by Engineer-in-Charge.

M&L TMT steel bars 10mm dia and over cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge.

Swami Enterprises

Durga Enterprises

m/s parmod kamar