ADDITION ALTERATION CUM SPECIAL REPAIR OF CERTAIN OTM ACCN AT DEHRADUN

Amount

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern as in roof coverings.Complete all as specified and directed.

Dismantling asbestos cement (corrugated , semi corrugated, etc.) sheets in roof coverings.Complete all as specified and directed.

Dismantling wall and ceiling boards, fibre or pulp, insulation etc. in insulation boards slabs, blankets any thickness incl cover fillets.Complete all as specified and directed.

Dismantling ceiling boards of any thickness and type from aluminium or GI frame work and refixing the same after repair work. Complete all as specified and directed.

Dismantling timber scantling 40 sqcm & over in section uframed in any position. Complete all as specified and directed.

Dismantling timber scantling 40 sqcm & over in section framed in any position.Complete all as specified and directed.

Ditto in fillets, rails, posts, rafters, purlins, etc. unframed work under 40 sq. cm in section. Complete all as specified and directed.

Taking up or down 15 mm steel tubing and connections complete all as specified and directed.

Taking up or down 20 mm steel tubing and connections complete all as specified and directed.

Dismantling of water tanks capacity exc 500 ltrs and n.exc 1000 ltrs. Complete all as specified and directed.

Dismantling of cast iron/ PVC /AC /SGSW pipes alongwith fittings and accessories upto 100 mm dia jointed in cement mortar and taking out of walls, floors or trenches, if required complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc. complete all as specified and directed.

Excavation in trenches n exc 1.5m wide & n.exc 1.50m depth for foundation & getting out in any type of soil complete all as specified & directed.

M&L for PCC (1:4:8) type D-2 (Using 40mm graded stone aggregate) as in sub base, foundation and mass concrete. etc complete all as specified & directed.

M&L for second class hardwood (Sal) in scantling, timber framed/unframed and fixed clean sawn.Complete all as specified & directed.

Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treating with creosote. Complete all as specified & directed.

S & F Pre - Painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. Make JSW Colour on + ISI Certified / TATA Dura Shine ISI Mark

S & F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick for Profile Ridge cover of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. Make JSW Colour on + ISI Certified / TATA Dura Shine ISI Mark

M & L 595 mm x 595 mm false ceiling system , using hot dipped galvanised steel section exposed surface with precoated capping, GI tee (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) and cross tee of size 24 x 32 mm & 24 x 27 mm having 0.27 mm gauge at every 600 mm c/c interval and wall angle of size 19 x 19 mm having 0.35 mm gauge fixed to the wall. The above grid is to be suspended at every 1200 mm c/c in both direction using 2mm thick pre-straightened GI wire laying designer tile ivory painted (high pressure steam cured) of 4 mm thickness (as per IS 14862) of size 595 x 595 mm and ant ine of the design e-board (cascadev or electra) , back of the tile duly sanded and finished with a coat of protective paint over the formed grid etc complete all as specified and directed. Make Everest, Armstrong, Himalayan

Dismantling floor, hearth or wall tiling including cement mortar bedding removing serviceable tiles to store and rubbish off the premises. Complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete as directed and specified.

M&L for 25 mm thick PCC 1:2:4, type B-0 (12.5 mm graded stone aggregate) as in floors to receive floor finishes. complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 400 X 400 X 7 to 8 mm thick (square/ rectangular) on floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6. Complete all as specified and directed.

M&L for Glazed ceramic tiles coloured 300mmx 450mm , 7 to 8 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match on vertical surfaces of wall incl 10 mm thick rendering on brick surface in CM 1:4. complete all as specified and as directed.

M&L Glazed Vitrified Tiles (GVT) 10 mm thick (Dark colour) (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6,complete all as specified and directed

M&L Vitrified tiles double charge 10 mm thick (Dark colour) (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in Skirting, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

M & L for 18 to 22 mm thick prepolished machine cut kota stone tile as in flooring incl 20 mm thick cement screed base in CM 1:6 , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including necessary grinding, rubbing and polishing. complete all as specified and directed.

All as per item no 27 above but on vertical surfaces of walls as in skirting and dados incl 10mm thick backing coat in CM 1:4. Complete all as specified and directed.

M&L for marble work 18 to 20mm thick, Makrana white (table rubbed and polished) in border strips, steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types Complete all as specified and directed.

M & L for Grinding, polishing to old kota stone flooring to achieve mirror finish Complete all as specified and directed.

M & L for 16 to 18 mm thick granite (Zed Black colour as approved by GE) stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in kitchen platform / dado / skirting 20 mm thick cement screed bed 1:6 CM in horizontal or vertical surfaces including grinding the edges half round and polishing complete all as specified and directed by Engineer-In- Charge.

Rounding to edge of stone slab one edge, such as in steps, cooking platform, and other similar situation. Complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thick (below or above ground level). Complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2, (using 40 mm thick graded stone aggregate) as in plinth protection and finishing even and smooth without using extra cement incl making joints 12 mm wide of full depth of PCC at every 3 meters and at every change in direction and filling the same with sealing compund grade 'A' incl necessary formwork. Complete all as specified and directed.

M & L for 75 mm thick cement concrete type D-2, 1:4:8 (using 40mm thick graded aggregate) including necessary form work as in sub base for flooring etc., complete all as specified.

M&L for brick work with sub class 'B' bricks built in CM 1:6 straight or curved on plan & exc 6 m mean radius with old size bricks. Complete all as specified and directed.

All as per Item No 36 above but except bricks Complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, in half brick thick wall built in CM 1:4 straight or curved on plan to any radius with old size bricks. Complete all as specified and directed.

S&F in repair stainless steel (304 Grade) Double bowl sink 1.00mm thick for kitchen with plug/waste pipe washers including cantilever bracket or, connecting unions etc overall size 1125 x 500 mm with bowl size 525mm x 450mm and 525 mm x 450 mm and depth 250 mm complete all as specified and as directed.

S&F in repair for 75 mm bore out let cast Iron floor trap (conforming to IS 3989) incl cockroach trap with gratings including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) etc complete all as specified and as directed

S&F Cast iron soil, waste and vent pipes 75 mm bore spun pipe in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified

S&F Cast iron soil, waste and vent pipes 100 mm bore spun pipe in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified

S&F in repairs PVC bends (any radius), diminishing pieces or tapers (larger bore measured). Complete all as specified and directed.

S&F in repairs PVC SWR floor trap outlet dia 75mm, plain with grating incl jointing with solvent cement. Complete all as specified and directed.

S&F PVC (SWR) pipes 75 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floor. Complete all as specified and directed.

S & F in repairs vitreous chinaware coloured counter type (oval) wash hand basin.Complete including fancy CP pillar tap, CP brass waste coupling ,waste pipe including fixing arrangement and cutting for and pinning in walls, slab & making good complete all as specifed and directed. Make Parryware Cat No C0419, Hindware 10038, S2030101 (snow white 3230).

S&F in repair Bib taps chromium plated, fancy type, screwed for iron pipe or for brass ferrule and fixed .complete all as specified and as directed. Make Hindware Cat No F730011, Cera F 2002152, Parryware G4880A1.

S&F in repair stop valves/angle valves fancy type chromium plated brass cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions fixed for 15 mm dia bore pipe complete all as specified and as directed

S&F in repair PVC connection of 45 cm length including brass nuts complete all as specified and as directed

S&F soap dish, any type, fixed to plugs with chromium plated brass screws of 160x160x90 mm complete all as specified and directed.

S&F 1000 litre rotational moulded tripple layer polyethlene water storage tanks white colour (cylindrical vertical with closed top) and suitable size of MS tasla with locking system hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F 20mm ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed etc complete all as specified and as directed

S&F medium grade galvanized steel tubing with all fittings & fixed complete to walls & ceiling or laid in floors 15 mm bore pipe (including in short length) complete all as specified and as directed

S&F tubes medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm bore pipe (including in short length) complete all as specified and as directed

Taking up or down 15 mm steel tubing and connections, including cleaning for refixing in new or old position(walls, ceiling, floors etc). Complete all as specified and directed.

Taking up or down 20mm steel tubing and connections, including cleaning for refixing in new or old position(walls, ceiling, floors etc). Complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone wall etc. including racking out joints, hacking for key and scrubbing down with water etc. complete all as specified and directed.

M&L for complete removal of existing treatment from wall upto plaster surface by washing, rubbing down and stopping of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces finally rubbed and smooth with sand paper.Complete all as specified and directed.

Raking out joints/ pointing to brick work/stone masonry in wall etc built in cement mortar.Complete all as specified and directed.

M&L for 15mm thick rendering on other than fair faces of brick / concrete surfaces in CM 1:6 finished even and fair. Complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick/ concrete surfaces in CM 1:4 finished even and fair. Complete all as specified and directed.

M&L for applying two coats of distemper oil emulsion over a coat of primer, white or tinted over 0.75 to 1 mm thick putty in two coat complete all as specified & directed.

M & L for Preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash on walls. all as specified & directed.

M& L for complete removal of existing treatment on walls and applying two coats of white wash on decorated surfaces. Complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. Complete all as specified and directed.

M & L for excavation in post holes (or similar holes) n.exc 0.5 Sqm on plan and getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m and making good surface all as specified. (soft/ loose soil).Complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-2 (40mm graded crushed stone agg) as in foundation, filling and mass concrete.Complete all as specified and directed.

S&F steel work in tubular trusses, vertical posts, purlins etc including special shaped washer, plates, and tubular purlins etc. complete using ERW or induction butt welded tubes .Complete all as specified and directed

S&F MS joist channel (Fe 410-W Gde E-250 quality A), angle or Tee section MS tubes, flats square bars etc as in roof trusses (framed), trsuused purlins, crane gantries, rails and fastening and heavy brackets including distance pieces, cleats etc. Complete all as specified and directed.

M & L for Erection and fixing only rolled sections as in purlins where connected to common rafters fixed with angle cleats or other connecting plates. Complete all as specified and directed.

M&L for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) including forming forming holes, confirming to Fe-410-W(GdeE-250) quality.Complete all as specified and directed.

M & L for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165. Complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 15 cm but n exc 22.5 cm long and dia of neck 16 to 20 mm. Complete all as specified and directed.

S&F tie bars with screwed ends, nuts, washers and mild steel plates for walls and straining bolts confirming to Fe-290Gde-E-165. Complete all as specified and directed.

S&F 0.50 mm thick prefabricated, colour coated galvalume aluminum zic coating GI based plain sheeting of any colour as directed by GE having tensile strength of 550 Mpa as in valley gutters/Eave gutters, drip and straight flashings (length and girth as fixed) .Complete all as specified and directed. Make JSW color on+, Tata durashine

M&L for cement concrete 1:2:4, type B1 as in copings , benching, bedplates etc. including all necessary formwork etc. Complete all as specified and directed.

M&L for preparing new steel or iron surfaces over 10 cm width or girth and applying two coats of black japan paint over one coat of red oxide primer.Complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n exc 4.0 sqm each including taking out of holdfast & making good in CM (1:4). Complete all as specified and directed.

All as per Item No 78 above, but not exc 1.5 Sqm each. Complete all as specified and directed.

Taking down shutters of any description exc. 1 sqm and n. exc 2 sqm each Complete all as specified and directed.

S&F 1.25 mm thick pressed steel frame of size 165 mm x 60 mm for door with one or more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed

S&F 1.25 mm thick pressed steel frame of size 125 mm x 60 mm for door with one or more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed

M&L for cement concrete 1:3:6, type C0 (using 12.5mm graded stone aggregate) as in bedplates, filling in pressed steel door frames etc. including all necessary formwork etc. Complete all as specified and directed.

S&F IInd class hard wood, 35mm thick skeleton shutters open rebated & prepared to receive, glass, gauge etc. (without sash bars), edge of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part I, Section 8, clause 8.24(a); supplied and fitted to chowkahts. Complete all as specified and directed.

S&F for Iind class hardwood Plain, solid, straight chowkhats and frames, wrought, framed rebated on solid, rounded or chamfered, put togrther with glued pinned at joints, supplied and fixed. Complete all as specified and directed.

M&L second class hardwood (Sal) Plain fillets. square, rectangular or triangular in section, sectional area exc 15 Sqcm but n exc 25 Sqcm, wrought, fixed with screws. Complete all as specified and directed.

M&L for IInd class hard wood, glazed and skeleton shutters for window/Ventilator, factory made , 30mm thick, open rebated and prepared to receive glass, gauze, etc.(without sash bars), and fitted with cut and mitred beads for securing glass, etc.; provided with stiles and rails as specified in SSR Part I, Section 8. clause 8.24 (b); and fitted to chowkats. Complete all as specified and directed.

All as per Item No 87 above, but divided in to square with plain, chamfered or rounded, mitred and rebated sash bars any numbers. Complete all as specified and directed.

S&F 40 mm thick factory made flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides (both the faces are covered with decorative face veneer with lapping/frame to match) Complete all as specified and directed.

S&F Ist class hard wood (shesam) small fittings such as brackets of any type, door stoppers and like including all necessary labours, articles n exc 200 cucm each. Complete all as specified and directed.

S & F factory made steel windows (Box type) powder coated with side hung shutters precoated (colour coated / powder coated) with double shutters (glazed and gauged shutter both ) with frame complete all as specified and directed and shown on drg TD 158 sheet 1/2 & sheet 2/2. NOTE :- Measurements shall be taken and paid compositly for frame, glazed and gauged. Grill shall be measured and paid seperately under respective item. Make (a) NCL Altek & Seccolor Ltd Hyderabad, (b) Ashwani & Sons Ghaziabad, (c) Ashwani Industries Ghaziabad

S & F for steel ventilator box type powder coated with top hung shutters precoated (colour coated / powder coated) with double shutters (glazed and gauged shutter both ) with frame complete all as specified and directed and shown on drg TD 158 sheet 1/2 & sheet 2/2. NOTE :- Measurements shall be taken and paid compositly for frame, glazed and gauged. Grill shall be measured and paid seperately under respective item. Make (a) NCL Altek & Seccolor Ltd Hyderabad, (b) Ashwani & Sons Ghaziabad, (c) Ashwani Industries Ghaziabad

M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165. Complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete, brick surrounds, glazed with putty or fixed with beads , complete all as specified and directed.

Material and labour for 4mm sheet glass, ordinary quality and glazing with oil putty / pins /spring pins and wooden beads in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

Resecuring or easing & adjusting without taking down shutters of any description not exc 1 Sqm each. complete all as specified and directed.

Taking down shutters of any description exc 1 and not exc 2 Sqm and refixing in same opening after easing and adjusting, each. Complete all as specified and directed by Engr-in-charge.

Supply and fixing mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples.Complete all as specified and directed.

S&F SS butt hinges medium weight, size 100 mm. complete all as specified and directed.

All as per item No 100 above but 75mm size complete all as specified and directed.

All as per item No 100 above but 50 mm size complete all as specified and directed.

S&F Stainless Steel handles fabricated type 150 mm size complete all as specified and directed.

All as per item 103 above but 100mm size complete all as specified and directed.

S&F Stainless Steel barrel tower bolt of extruded section 200 mm length of bolt complete all as specified and directed.

S&F in repairs Stainless Steel tower bolt of extruded section 200 mm length of bolt complete all as specified and directed.

S&F 100 mm long Stainless Steel barrel tower bolt of extruded section complete all as specified and directed.

S&F in repairs 100 mm long Stainless Steel barrel tower bolt of extruded section complete all as specified and directed.

S&F Stainless Steel door bolt of length 300mm sliding door bolts length 250 mm, plate type,with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed. Complete all as specified and directed.

All as sper Item No 109 above, but fixed in repairs. complete all as specified and directed.

M & L for Preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer. Complete all as specified and directed.

M & L for Preparation old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S & F 25 mm dia Stainless Steel 1 mm thick decorative curtain rod including fancy type brackets fixed to wall complete all as specifed an directed.

Demolition of cement concrete (reinforcement cut as reqd to facilitate demolition) of any description & in any position not specially provided for Complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) (nominal mix) as in slabs supported on wall, landing, balconies, canopies, deck slabs and in shelves and like in repair to Chajjas, Claddings, soffits etc including bonding agent, complete all as specified and directed.

M&L for form work to sides and soffits of cantilevers, shelves incl supports overhang etc, rough finished surfaces of concrete flat, complete all as specified and directed.

M&L for TMT Bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete incl welding etc (if reqd) all as specified and directed.

All as per item No 117 above but 6mm to 8mm complete all as specified and directed.

S & F factory made WPC single extruded 100% lead free ROHS certified board of 18mm thick pre laminated shutter for Cook house cabinets. The laminated shutter should be pre laminated from one side and other side plain white of density not less than 600 kg / cum manufactured by an ISO 9001:2015 certified company. The 18mm board should be 100% lead free, water proof, termite proof and borer proof and should have good screw holding capacity and complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanized, width of flap 30 mm complete all as specified and directed.

S & F hydraulic concealed hinge with clip on installation and integrated Silent System, opening angle not less than 100º, For shutter thickness 15 - 24 mm full overlay type shutters, hinge cup dia 35 mm including necessary fixing arrangement with SS screw complete all as specified & directed.

S & F floor door stopper of aluminium body and tongue, anodised, with hard drawn steel spring, overall length of cover plate 140 mm and fixed to door shutters.Complete all as specified and directed.

S&F 100mm Aluminium handles, cast type, anodised complete all as specified and directed.

S&F 100mm hasp and staple, aluminium anodised, including mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

M & L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron. Complete all as specified and directed.

M & L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors. Complete all as specified and directed.

S& F 4 mm dia plain mild steel wire, galvanised class 3, in detached work such as for mosquito nets and fixing to straining bolts, hooks, eyes, etc. Complete all as specified and directed.

Rough excavation not exceeding 1.50 m deep and getting out soft/loose soil. Complete all as specified and directed.

Removing excavated material exceeding 250M but not exc 500m and depositing where directed. Complete all as specified and directed by Engineer-In- Charge.

Returning/filling trenches, including spreading levelling, watering, well ramming in layers n.exc 25 cm complete all as specified and directed.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing. Complete all as specified and directed. Make- Rajshree / Eco cell / Floresta

Surface excavation n exc 30 cm deep and averaging 15 cm and getting out in any type of soil complete all as specified and directed.

Removing excavation material surplus soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified & directed.

M& L for 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor / pavings complete all as specified and directed.

M&L heavy duty coloured parking tiles 10 to 12 mm thick dark shaded (Square / rectangular ), area of each tile not exceeding 0.36 sqm in floor etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade, incl 15 mm thick screed bed in cement mortar 1:4. Complete all as specified and as directed.

Excavation in trenches n exc 1.5m wide and n exc 1.50m in depth for foundation etc and getting out in soft/loose soil complete all as specified and directed by Engineer-In- Charge.

M&L for brick work with sub class 'B' bricks old size bricks strainght or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and directed by Engineer-In- Charge.

M&L for 15mm thick rendering on other than fair faces of brick work in CM 1 : 6 finished even and smooth without using extra cement complete all as specified and directed by Engineer-In- Charge.

M&L for PCC 1:2:4 type B-1, using 20 mm graded stone aggregate as in coping and similar work incl necessary form work to obtain a smooth finishes complete all as specified and directed by Engr-In- Charge.

M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement incl forms, moulds, mi-tred/stopped ends etc. complete all as specified and directed by Engineer-In- Charge

M&L for PCC 1:3:6 type C-2, (40 mm graded stone aggregate) as in surface channels and drains. (Saucer Drain) complete all as specified and directed.

Supplying and fixing of unplasticized Poly Vinyl Chloride (UPVC) Openable doors with Open able shutters duly manufactured using UPVC reinforced profiles (Composition of profile shall consists minimum of 5.5 PHR of TiO2 and not more than 12PHR of CaCo3 for every 100 parts of PVC resin) of 60 mm x 55mm x 2.40 mm for outer frames, 60 mm x 74 mm x 2.40 mm for mullion sections as per the need and 60 mm x 102 mm x 2.40 mm for Open able shutter frame capable of mounting single glazing system structurally reinforced with hot dip galvanized up to 50 microns of minimum thickness of 1.2 mm prefabricated & welded through fusion welding the door sash shall be fitted with 5 mm thick clear toughened glass of reputed make duly fixed with Grey colour TPV Gaskets for sash & Glazing bead shall be coextruded with Grey colour soft PVC. System shall be provided with 4 no’s of 3D Hinges for each shutter and multipoint locking with keys as per the need. with raiser wedges for smooth operation and the system is to be installed at the site using anchor fasteners, silicon rubber sealant, easy glazing/ deglazing at site etc., including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site complete for finished item of work complete all as specified and directed. Note: The unit rate quoted by contractor includes cost of glass and all other connected accessories. Net opening shall be measured for payment purpose

Supplying and fixing of Unplasticised Poly Vinyl Chloride (UPVC) 3 track sliding Window with mesh shutter – (2-glass shutter and 1-meshshutter) duly manufactured using UPVC reinforced profiles (Composition of profile shall consists minimum of 5.5 PHR of TiO2 and not more than 12PHR of CaCo3 for every 100 parts of PVC resin) of (108 mm x 45 mm) x 2.20mm for outer frames, (39mm x 58mm) x 2.20mm for sliding shutter frames capable of mounting single glazing system structurally reinforced with hot dip galvanized up to 50 microns of minimum thickness of 1.0/1.2 mm prefabricated & welded through fusion welding. The window sash shall be fitted with 5mm thick clear toughened glass of reputed make and mesh shutter frame shall be (30mm x 48.5mm) x 2.0 mm fitted with Vinyl Coated Fiber mesh- on rollers/pulley duly fixed with Grey colour TPV Gasket for sash & Glazing bead shall be co-extruded with Grey colour soft PVC. Window shall be provided with standard hardware &Single point locking system of touch Lock system. the system is to be installed at the site using anchor fasteners, silicon rubber sealant, easy glazing/deglazing at site etc., including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site complete for finished item of work complete all as specified and directed. Note: The unit rate quoted by contractor includes cost of Glass, Wire Mesh and all other connected accessories. Net opening shall be measured for payment purpose.

S&F Door closer hydraulically regulated Aluminum (extruded section) body, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified & directed.

S&F Sink mixer (wall mounted), chromium plated, fancy type, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F PVC (SWR) pipes, 110mm bore single socketed in any length with rubber ring joint fixed to walls complete all as specified and directed.

S&F PVC (SWR) bends bore 110mm in any radius complete all as specified and directed.

Taking down carefully copper/Aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder and regulator etc and removing from site and making good disturbed surfaces of walls/floors etc complete all as specified and directed by Eng-in-charge

M&L in Replacement for existing point wiring with 1.5 Sqmm (nominal area) two single core PVC insulated unsheathed multi stranded copper conductor cable 1100 volts grade, FRLS-H grade in and including medium duty concealed PVC conduit 20 mm dia or higher and conduit fittings with cutting chases and all accessories with suitable size of sunk type cast iron or pressed steel terminal box 1.2mm thick, duly painted for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, including contineous earth wire PVC insulated, unsheathed, multi stranded copper conductor cable 1.5 sqmm (nominal area) FRLS-H grade, green colour, up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of the following. (Note: Colour code shall be maintained as per IE rule)

(a) One light point /bell buzzer point controlled by one-one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

All as per item No 144 above but one 5 pin socket outlet 15/5 Amp independent, with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm.

M&L for new point wiring with 1.5 Sqmm (nominal area) two single core PVC insulated unsheathed multi stranded copper conductor cable 1100 volts grade, FRLS-H grade in and including medium duty concealed PVC conduit 20 mm dia or higher and conduit fittings with cutting chases and all accessories with suitable size of sunk type cast iron or pressed steel terminal box 1.2mm thick, duly painted for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, including contineous earth wire PVC insulated, unsheathed, multi stranded copper conductor cable 1.5 sqmm (nominal area) FRLS-H grade, green colour, up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of the following. (Note: Colour code shall be maintained as per IE rule)

(a) One light point /bell buzzer point controlled by one-one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

All as per item No 150 above but one 3 pin socket outlet 15 Amp independent, with cable 2.5 Sq mm size, with earth continuity coductor of size 2.5 Sq mm.

S&F switch piano flush, button type 5 Amp SP 240 V AC complete all as specified & directed. Make: Legrand/Crabtree/Indoasian/Cona

S&F switch piano flush button type 15 Amps SP 240 V AC complete all as specified & directed. Make: Legrand/Crabtree/Indoasian/Cona

S&F socket outlet multipurpose 3 Pin 5 Amp and 2 pin 5 amp 240 V AC complete all as specified & directed. Make: Legrand/Crabtree/Indoasian/Cona

S&F socket outlet 2 in1 ,3 pin 5 Amp and 15 Amp flush type complete al as specified. Make: Legrand/Crabtree/Indoasian/Cona

S&F stepped type electronic fan regulator flush type socket type 120 Watt on the existing phenolic laminated sheet etc as required. Make: Legrand/Crabtree/Indoasian/Cona

S&F ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 240 V AC complete all as specified and directed. Make: Legrand/Crabtree/Indoasian/Cona

S&F lamp holder PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed. Make: Legrand / Crabtree / Cona

M&L in replacement (including taking down old sub main wiring) sub main wiring with 2 Single core PVC insulated unsheathed FRLS-H cable 1100 Volts grade heavy duty copper conductor multistranded of size 6 Sq.mm. (nominal area) drawing in and including 20 mm. dia or higher PVC conduit medium duty concealed, conduit heavy duty accessories and fittings including chasing cutting Insulated unsheathed FRLS-H cable copper conductor multistranded of size 6.0 Sq. mm. as earth wire upto common earth and connected to earth dolly complete all as specified & directed. Note:- Two runs of 6 Sqmm, one run of 20 mm dia conduit and one run of 6 sqmm copper wire as earth wire shall be measured and treated as unit.

Supply & fixing and Testing New TP & N Vertical load line (VTPN) 4 way 415 Volts 50 Hz indoor type double door sheet metal enclosure IP-43 DB's IK-09 flush mounted with 250 Amp Copper busbar for each phase with two neutral bar & two earthbar and cable ties for cable management including Provision of MCCB 63 Amps,ICs=100%ICu, 16KA four pole as in comer including connecting terminal strip complete and SP MCBs as out going etc complete pre wired with suitable size copper conductor. The DB's shall hold type test certificate (CPRI) as per IEC 61439-3 complete all as specified and directed by Eng-in-charge including taking out old unserviceable DB and removing from site. Make Havells / Legrand / C&S (Note :- MCB/ MCCB shall be measured and paid separately)

S&F in replacement sheet metal enclosures 240 volt with 200 amps rated copper bus bar for double door 8 way IP-43DB's lk-09 suitable for one MCB SPN as incoming and 6 MCB SP as out going, mounting flush on wall and making good disturbed surfaces complete all as specified and directed by Engr-in-charge ,including taking down old unserviceable DBs . Make Havells / Legrand / C&S Note (MCBs shall be measured and paid separately).

S&F MCB double pole 240 Volt 10 KA 40-63 Amp 'B' series conforming to ISI marked complete all as specified & directed . Make Havells / Legrand / C&S

S&F MCB single pole and neutral 240 volt 10 KA 5-32 Amp 'B' series conforming to ISI marked all as specified and directed . Make Havells / Legrand / C&S

S&F MCCB 415 Volt 16 KA 4 pole 63 Amp magnetic trip release & setting as incoming with fixing arrangement complete all as specified and directed. Make Havells / Legrand / C&S

Supply & fix in replacement LED light fitting 1x20 W,220V AC decorative box type with driver ,holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make: 1) Bajaj Cat Part No - (a) BC150 20W WH(For Batten) (b) BLRB 20W LED(For Tube) 2) Crompton Cat Part No - (a) DIJB12LT.8.20(For Batten) (b) LT 8.20-865(For Tube) 3) Havells Cat Part No - (a) REGAL BATTEN BUPT01X20W JSBS(For Batten) (b)PHOTONULTRAE2.01213T118WLED 865 PC(For Tube).

Supply & fix new LED light fitting 1x20 W,220V AC decorative box type with driver ,holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make: 1) Bajaj Cat Part No - (a) BC150 20W WH(For Batten) (b) BLRB 20W LED(For Tube) 2) Crompton Cat Part No - (a) DIJB12LT.8.20(For Batten) (b) LT 8.20-865(For Tube) 3) Havells Cat Part No - (a) REGAL BATTEN BUPT01X20W JSBS(For Batten) (b)PHOTONULTRAE2.01213T118WLED 865 PC(For Tube).

S & F high efficiency LED bulbs 1 X 12 watt that can be used as a ready replacement for existing GLS ad CFL direct fit in holder complete all as specified and directed. Make Philips / Havells / Wipro

S&F ceiling fans complete with blades ,down rods ,with fan regulator and accessories ,230 V ,1200mm sweep.Min air delivery 210 CFM with service value 6.00 BEE Five Star Rated with Brushless Direct Current(BLDC) Motor. Note:(1)Rate for hanging arrangements of Ceiling Fan deemed to be included. (2) Old ceiling fan shall be deposited in E/M storeyard . Make:-1) Bajaj Model No -ENERGOS 35 2) Crompton Model No-.ENERGION HS 1200mm 3) Havells Model No - HAVELLS GLAZE 1200mm BLDC

Supply & fix exhaust fans steel body AC single phase 230 V of size 450 mm sweep with blades ,frame and louvers.M&L for making Holes of suitable size and making good disturbed surfaces as directed by Eng-in-charge deemed to be included in the quoted rate. Note: (1) Old Exhaust fan of any capacity shall be deposited in E/M storeyard . Make:-1) Bajaj Model No -MAXX AIR 450mm 2) Crompton Model No-.TRANS AIR 450mm 3) Havells Model No - VENTIL AIR DB 450mm

M&L for earthing complete with using galvanized mild steel earth plate (electrode) 600 mm x 600 mmx 6 mm thick buried directly in ground, earth pit not less than 2.25 mtr deep below ground level with top edge of the earth plate not less than 1.50 m below ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to be packed thickness of 15 cm all round the plate using 4 mm dia GI earth lead wire as earth lead moulded and rivetted to earth plate at one end and connected to main equipment at switch/control board at another end, GI earth lead protected in and including 15 mm dia GI ‘medium grade’ pipe from upper end of earth plate upto equipment with & including 20 mm dia bore GI pipe ‘medium grade’ as water pipe from earth chamber to upper edge of the earth plate, GI funnel with wire mesh fixed on water pipe and provision of PCC 1:2:4 type B1(using 20 mm graded stone agg) as in pits chamber and RCC pit cover 50 mm thick of precast RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as per electrical plate No.3 of SSR Part-II 2010 and testing on completion all as specified and directed. Note-(i) if the desired earth resistance is not found within permissible limit item shall be re-done by contractor at no extra cost. (ii) Cost of GI wire 4 sqmm and 15mm dia pipe medium grade is deemed to be included in the rate quoted for this item

S&F mirror light decorative compact luminarious with decorative ends caps 9/10 Watt LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F LED light fitting decorative wall mounting Brass bracket suitable for 5 watts LED bulbwith frosted glass with and including one no 5 watt LED lamp. complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver,holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. Make:-1) Bajaj Cat Part No -BZRSQL 43L LED GX PRO WH 2) Crompton Cat Part No –LDTLBK-36W-CDL 3) Wipro Cat Part No - LM10-451-XXX-40-G2

Supply and Fixing in replacement Integral LED Street Light Luminaire comprising of high pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 36/40 watt with efficiency 100 lumen/watt at system level, CCT>5700K, with average life class 50,000 burning hours including GI brackete made out of 25 mm GI pipe medium grade and MS clamps for fixing of light fitting complete and connected with twin core PVC insulated copper flexible cable with existing point all as specified and directed. Make:-1) Bajaj Cat Part No -ENXT P 36L WH PO PC SD 2) Crompton Model No-.LSTS-40-CDL-M(Astra Neo 3) Wipro Cat Part No - LR02-451-XXX-57-G1

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core complete all as specified and directed.

M&L for laying local dry clean sand filling for cushioning in trenches around under ground cable complete all as specified and directed.

M&L for laying well burnt brick, old size in trenches, as protection of under ground cable complete all as specified and directed.

Suppy and fix GI pipe 40 mm light grade galvanised with all fitting laid in trenches for protection of cable complete all as specified and directed.

Note : Tenderers may note that amount of credit Rs 4,02,765.00 will be deducted from the total amount arrived, at the time of Acceptance of contract.

Panwar Construction Co.

yash enterprises

M/s Arihant Builders