Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹4.8 LAccepted-AOC | L1 | Accepted-AOC FIRST LOWEST BIDDER | |
| 2 | L2₹5.1 L+₹29,848.53 (6.18%)Rejected-AOC | L2 | Rejected-AOC SECOND LOWEST BIDDER |
Tender Value
₹5.3 L
EMD Value
₹13,158
Closing Date
18 Feb 2025, 2:00 pmClosed
Sindu V G
Assistant Executive Engineer
State Plan-2024-25-RWSS to Puducode- Balance Work-Installing prefabricated pump house, supply and erection of motor pump set and interlinking to the existing pipe line at Thekkepotta area in Puducode grama panchayath-General Civil Work
2025_KWA_737041_1
20284/2024_5_3_2/2
Open Tender
Civil Works - Water Works
Item Rate
Puducode
Please refer Tender documents.
8 documents required · 8 mandatory
₹1,165
₹13,158
Yes
1 Mar 2025
12 Feb 2025
19 Feb 2025
12 Feb 2025
18 Feb 2025
12 Feb 2025
Amount
SUPPLY AND FIXING SUBMERSSIBLE MOTOR PUMP SET
OD221898/2024-2025:1) Supply, erection, testing and commissioning of KWA prequalified reputed make tube well submersible pump set with SS impeller, SS shaft and CI pump casing suitable for bore well with 180 mm dia inner casing pipe. The duty condition is as follows 2) Motor - Supply, erection, testing and commissioning of KWA prequalified reputed make vertical solid shaft foot mounted TEFC 3phase induction motor suitable for the above pump set working 3 phase, 50 Hz , 415 V working in AC supply. 3) Soft Starter - Supply erection, testing and commissioning of suitable rating (Fully automatic ) starter for the above motor with over voltage and under voltage protection , single phase preventer, over load relay with motor protection relay complete 4) Panel board (suitable for operating two pump sets bunt one pump set at a time ). 5) Valves- Supply of suitable size best quality heavy duty ISI marked double flanged sluice and Non return valves with suitable pressure rating. Fitting of valves shall include proper RCC support especially for Non return valve. 6) Suction and delivery pipe connections - Supply and fitting of suitable size best quality G I pipe (Medium) for total length of 10 meter suitable for the above pump set connecting the delivery side of the pump with valves and suitable specials to connect with the pumping main. 7) Supply and installation of suitable glycerin filled pressure gauge. 8) Maintenance for a period of two years
OD221902/2024-2025:Supply conveying and fixing of three phase, 415 volt and 50 Hz module for mobile starter & submerssible controller conforms to IS/IEC 60947-4-1 with features of auto restart, vibration proof enclosure with IP54 protection class, ON/OFF , voltage and ampere indication and protection against overload, single phasing , phase reversal , phase imbalance. etc
OD221901/2024-2025:Supply and erecting 24 Gauge 63mm dia uPVC submerssible column pipe. including cost of pipe and specials and all labour charges,hire charges of machineries ,etc. complete as per the direction of departmental officers
OD221899/2024-2025:Supplying and fixing 6 sq mm three core flat submersible cable
OD221900/2024-2025:Providing and fixing 50mm pvc casing pipe for cable ,including earth work,cost of materials and all labour charges.etc complete as per the direction of departmental officers.
CONSTRUCTION OF PUMP HOUSE
OD221903/2024-2025:Supply and instalation of prefabricated concrete cabin pump house of Inside size 1.8m x 1.5m and height 2m above basement with RCC roof gabled or flat. The cabin have one door frame, 2 nos of Ventilators with RCC grill including the supply and erection of RCC post and slab for fixing the panel board including the cost of materials and all labour charges. including transportation and erection charges etc. Complete as per the direction of departmental officers.
13.37.1:White washing with lime to give an even shade:New work (three or more coats)
11.3.1:Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate)finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate
10.5.1:Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces
2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil
50.6.1.4:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand ) etc complete
13.9.2:Cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement.20 mm cement plaster
LINKING BORE WELL WITH EXISTING PUMPING MAIN
100.1.1:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50m, in all kinds of soil.
100.8.1:Fencing one side of trenches, 1.50m height with two rows of 10cm plastic caution tape in vertical casuarina pole (girth 15cm to 24cm) fixed at 2m intervals.
15.43.2:Dismantling manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in-Charge:Bituminous road
100.31.1.1:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 80mm diameter, Class I.
100.9.8:Laying uPVC pipes of class 2 to class 6 and specials, lowering to the trenches already made, placing in position aligning the pipeline to the lines and levels and jointing the pipes and specials with solvent cement and testing the pipeline with water to the required test pressure (excluding cost of pipes and specials): 90 mm nominal outside diameter pipes.
OD221904/2024-2025:Linking of existing 90mm pvc distribution line to new line, including all labour charges and charges for hire and conveyance of tools and plant, cost of consumable charges for lighting ,watching,ribbon fencing,caution boards,traffic diversion,as per the direction of departmental officers etc.
OD221926/2024-2025:Linking of existing 160mm pvc pumping line to new line, including all labour charges and charges for hire and conveyance of tools and plant, cost of consumable charges for lighting ,watching,ribbon fencing,caution boards,traffic diversion,as per the direction of departmental officers etc.
4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)
OD221905/2024-2025:Providing and fixing Protection tube for Sluice/GM Valve size up to 150mm
SUPPLY OF MATERIALS
100.98.236:Supply of PVC Pipe, 10kg/cm2, 90mm Dia.
18.12.8:Providing and fixing G.I. pipes complete with G.I fittings including trenching and refilling etc. External work80 mm dia nominal bore
OD221907/2024-2025:Cost of PVC specials @ 3%of cost of PVC pipe used
OD221908/2024-2025:Cost of GI Specials @ 5% of cost of GI pipe used
100.98.457:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 80mm.
KSEB Charges
OD221909/2024-2025:Cost of KSEB Connection charges
FRANKLIN JOSE (BID ID -2113721)
Bidder Name
M SIVADAS
FRANKLIN JOSE
tech_eval.pdf
fin_eval.pdf
aoc.pdf
finance_1182256.pdf
boq_comp_chart.xlsx
xlsx
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .