Improvement to old S V Balamandir hostel building in SV Balamandiram Tirupati

Demolition including stacking of serviceable materials and disposal of unserviceable materials within 100 metres lead for Brick Masonry.

Dismantling, clearing away and carefully stacking materials useful for re-use Flat stones in roof or floors including lifting

Demolishing and disposal of unserviceable materials within 100 metres lead - Unreinforced cement concrete up to 15cm thickness

Conveyance of excavated surplus earth/debris to a distance 3kms from the site of work at the place specified by the Engineer-in-Charge including loading and unloading etc., complete as directed during execution.

Filling of foundations and basement with best river sand in layers of not more than 15 cms. thick each well watered to saturation and consolidated including cost and conveyance of all materials, incidental charges etc., complete.

Cement Concrete (1:4:8) using 40 mm ( 0.54 Cum), 20mm (0.27 Cum) and 12 mm (0.09 Cum)nominal size hard broken granite crushed metal from any source conforming to the relevent ISI standards for foundations etc., laid in layers of not more than 15 cms thick well compacted including curing,machine mixing, cost and conveyance of all materials etc., complete.

Cement Concrete (1:2.5:5) using 20 mm ( 0.54 cu.m) and 12 mm (0.36cu.m) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cms thick well compacted including curing, machine mixing, cost and conveyance of all materials etc., complete. Note: Measurement boxes shall be used for measuring the quantities of cement, aggregate and water required for the given concrete mix.

Construction of Brick Masonry in CM (1:6) using well burnt Bricks 2nd class or ground moulded (Non modular or traditional size) (230 x 110 x 70 mm) including curing, cost and conveyance of all materials as directed during execution and complying with standard specifications etc., complete.

Construction of 110 mm thick Brick partition walls in C.M.(1:4) using well burnt bricks 2nd class or ground moulded (Non modular or traditional size) bricks (230X110X70 mm) including curing, cost and conveyance of all materials etc,. complete

Supply and placing of the M20 Design Mix using of 10 mm HBG crushed metal 0.480 cu.m, 6 mm HBG Crushed metal 0.320 cu.m, sand 0.400 cu.m and cement 350 kg with water cement ratio of 0.53 (185.50 ltrs/cu.m of CC) etc., from any source conforming to the relevant ISI standard including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing including centering charges, shuttering charges etc., complete with minimum cement content as per IS code from standard suppliers approved by the department but excluding cost of steel and its fabrication charges, for finished item of work

-do- 50mm thick precast slabs using 10 mm graded aggregate of HBG crushed metal from any approved quarry with necessary reinforcement excluding cost of steel and tying of grills, centering charges but including cost of necessary form work and cost and conveyance of all materials curing as directed by the department.

RCC M20 Design mix precast slabs 80 mm thick using 20 mm size graded HBG crushed metal

Providing High Yield Strength deformed (HYSD)/ Thermo mechancially treated (TMT) steel bars of below 36 mm Fe-500/ Fe-500D (as per IS 1786 - 2008) of different diametres for RCC works, including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars including all wastages such as over laps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all floors. (APSS NO.126) (In the absence of 18G binding wire,2 nos of 20G binding wire in tandem are to be strictly adhered). Note: Unless otherwise fabrication and placement of steel, no pre-pament shall be made against the supply of steel reinforcement

Plastering using best river sand including cost and conveyance of all materials, screening, curing, rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete.

In CM(1:5) 12 mm thick

In CM(1:5) 20 mm thick

Finishing the sides of walls with I st quality glazed red or white full body ceramic wall tiles of size 300 x 600 mm and thickness between 6-8 mm conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs of approved colour and brands including pointing the joints with the same colour of cement by mixing the same colour pigment in white cement and over a bed of C.M.(1:3), 12 mm thick & Cement slurry of 33 Kg/10sq.m shall be used for fixing bed tiles including cost and conveyance of all materials, curing, incidental charges etc., complete (No separate plastering shall be paid to the walls). (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply). -

Flooring with Antiskid floor tiles Non-skid red or white full body Ceramic floor tiles of size 450 x 450 mm and thickness between 7-8 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs1st quality of all series & shades (as per manufacture specification), set over base coat of cement mortar (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including white cement slurry of honey like consistency spread @ 3.30 kgs per sq.m. jointed with neat cement to full depth mixed with pigment of matching shade, including cost and conveyance of all materials like flooring slab, cement, sand and water etc., complete, for finished item of work.

Supplying and fixing in position Flush door shutters, solid bond wood block board type with commercial ply on both faces.: 35 mmthick conforming to IS:2202 of standard make with hot pressed bonded with liquid phenol formaldehyde with rebate cutting, Single leaf using Best Indian Teak wood frames of size 75mm x 100mm without threshold plate, including cost of M.S "Z" Hold fasts of 230 x 50 x 6mm, M.S Powder coated Butt hinges of 125 x 65 x 2.12mm, screws, nails, etc., complete, (excluding cost of other fixtures which will be paid separately but including labour charges for fixing the fixtures).

Supplying and fixing in position Flush door shutters, solid bond wood block board type with commercial ply on both faces.: 30 mmthick conforming to IS:2202 of standard make with hot pressed bonded with liquid phenol formaldehyde with rebate cutting, Single leaf using Best Indian Teak wood frames of size 75mm x 100mm without threshold plate, including cost of M.S "Z" Hold fasts of 230 x 50 x 6mm, M.S Powder coated Butt hinges of 125 x 65 x 2.12mm, screws, nails, etc., complete, (excluding cost of other fixtures which will be paid separately but including labour charges for fixing the fixtures).

Supply and fixing of 35 mm thick Flush door shutters, solid bond wood block board type with teak veneer on one face and commercial ply on another face (lipping) conforming to IS:2202 of standard make. solid core flush doors , with Commercial facing both sides with hot pressed bonded with liquid phenol formaldehyde with rebate cutting, including cost of screws etc., complete ( excluding cost of other fixtures which will be paid separately, but including labour charges for fixing the fixtures).

Supply and fixing of 30 mm thick Flush door shutters, solid bond wood block board type with teak veneer on one face and commercial ply on another face (lipping) conforming to IS:2202 of standard make. solid core flush doors , with Commercial facing both sides with hot pressed bonded with liquid phenol formaldehyde with rebate cutting, including cost of screws etc., complete ( excluding cost of other fixtures which will be paid separately, but including labour charges for fixing the fixtures).

Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebate of 32MM. '--do-- Door Frame section of 45x75 MM . The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member.

Providing and fixing 28-30 MM thick solid Wood Polymer Composite (WPC) Single extruded door shutter with 3MM top and bottom rigid layer with an overall density of 750kg/Cum. It will be fixed to the frame using 3 inch /4 inch hinges. Minimum of 4 hinges will be required for fixing the door with the frame.

Supply and fixing of cupboard shutter using teakwood scantling of size 50mm X50mm teakwood as outer frame and 50mm X 30 mm of size teakwood for shutter frames , 8mm thick Bison Lam as panel to each shutter consist of 2 Nos 75mm long tower bolt – 2 nos 75 mm big handle the and other shutter will have 1 no of cupboard lack , 1 No of 75 mm long handle and 75mm10mmX1mm thick SS hinges- 2 Nos for each shutter. The above frame will be fixed to the wall with screws, the rate inclusive of screws, handle, etc., complete at site of work.

Supply and fixing of 1.5 to 2 mm thickness PVC sheet for toilet doors including screws, Nails and etc., complete as directed during execution.

Supplying and fixing in position M.S Ornamental grills for windows and ventilators or for veranda openings using M.S. Flats, square rods, angles sheets etc., of approved design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with Two coats with Synthetic enamel paint Gr-I over a Primary coat (Red oxide metal primer) (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.

Supply of Anodized Alluminium Aldrops sliding door bolts 16 mm X 300 mm (3T- pieces)

Supply of Anodized Alluminium Aldrops sliding door bolts 16 mm X 200 mm (3T- pieces)

Supply of Anodised Alluminium tower bolts 12 mm dia with ISI Mark IS 204 - 12 mm x 250 mm long

Supply of Anodised Alluminium tower bolts 12 mm dia with ISI Mark IS 204 - 12 mm x 200 mm long

Anodized Aluminium Door Handles (IS:208) of 150 mm long

Supply of Plain Float Glass 6 mm thick

Providing and fixing factory made UPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of UPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforcedwith 1.60 ± 0.2 mm thick galvanized mild steel section made from rollforming process of required length (shape & size according to uPVCprofile), appropriate dimension of uPVC extruded glazing beads anduPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (whitepowder coated) touch locks with hook, zinc alloy body with single nylonrollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mmsize for fixing frame to finished wall and necessary stainless steel screwsetc.

Profile of frame & sash shall be mitred cut and fusion welded at allcorners, including drilling of holes for fixing hardware's and drainage ofwater etc. After fixing frame the gap between frame and adjacent finishedwall shall be filled with weather proof silicon sealent over backer rod ofrequired size and of approved quality, all complete as per approved drawing& direction of Engineer-in-Charge inclusive of cost of Single / double glass panes, wire mesh and silicon sealent . Note: For uPVC frame and sash extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted. But no extra payment on this account shall be made.

-do- Three track three panels sliding window with fly proof SS wire mesh(Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing factory made UPVC white colour fixed glazed Windows / Ventilators comprising of UPVC multichambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile),uPVC extruded glazing beads of appropriate dimension, EPDM gasket,G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plasticpackers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (ifrequired) shall be also fusion welded including drilling of holes for fixinghardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof siliconsealant over backer rod of required size and of approved quality,

all complete as per approved drawing & direction of Engineer-in-Charge inclusive of cost of Single / double glass panes and silicon sealant. Note: For uPVC frame, sash and mullion extruded profiles minus 5%tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Fixed windows / Ventilators made of (small series) frame 47 x 50mm & mullion 47 x 68 mm both having wall thickness of 1.9 ±0.2 mm and single glazing bead of appropriate dimension

Providing Unplasticized PVC SWR Rain water downfall pipes for the following dia with ISI:13592 Type -A mark with necessary shoes, bends, collars etc., including making holes in walls, RCC slabs, beams, columns, including fixing with necessary wooden plugs (where it is required pipe clear of wall, wooden blocks of size equal to that of ears of the pipe shall be used), screws, iron clamps of 18 G and making good the same including cost and conveyance of all materials and incidental charges etc., complete as directed during execution. - do - 110 mm dia PVC pipe with wooden block of size 150mmx50mmx50mm

Supply of PVC /SWR pipes & fittings ( as per ISI standards) 6kg/cm2 (Type-B) including labour charges for laying, fixing and commissioning the PVC pipes including couplers/bends/tees etc., any dia including fixing necessary fittings like bends, plugs, couplers, junctions, tees, etc.,., with solvent jointing as per standard practice.

.do. 110 mm dia Single socket pipe

.do. 75 mm dia Single socket pipe

.do. 160 mm dia Double socket pipe

Supply of the following U.V resistant UPVC SWR pipe fittings (as per BIS standards)

-do- 110 mm dia - Door Bend 87.5 Degrees

-do- 110mm dia Plain Bend 87.5 Degree

-do- 110mm dia Single Tee (With Door)

Supply of 4" (101.6 mm ) Nahany Trap ( Without Jali with inlet)

Supply of Round Jali

Supply & fixing NP soap dish heavy type with NP Screws

Supplying & fixing NP coat hook

Supplying and fixing TV shape mirror with plastic frame size 609.6 mm x 457 .2 mm

Supplying and Fixing European Water Closet of 1st quality confirming to IS:2556-Part-2-1973 of white glazed with 'P' trap with ISI mark or equivalent brand approved by the department.

Supplying & Fixing Orissa Pan white glazed W.C 1st quality ISI marked confirming to IS:2556-Part-3-1981 with "P" or "S" trap ISI Mark or equivalent brand approved by the department - 580 x 440 mm

Supply & fixing of PVC low level system 10 litres capacity Dual Flush with internal components & short bend.

Supplying and Fixing best Indian make plastic seat and lid for European water closets with rubber or plastic Buffers as per IS 2548-1996

Supplying & Fixing Indian make Flat Back Wash Hand Basin of size 550 x 400 mm - single C.P. Pillar cock.1st quality conforming to IS:2556-Part-4:1972 with ISI mark or equivalent approved by the department, with waste fittings like rubber plug, chain, 32 mm nominal size C.P. Fitting with parallel pipe thread conforming to IS:2963-1979 and fitted with 15 mm nominal bore Chromium Plated Pillar Tap of 1st quality Indian make 400 grams complete with standard CI brackets including wooden block

Supply and fixing CP Long body bib cock fancy type deluxe heavy duty 12.7mm dia Indian make 400 grams

supply and fixing CP short body bib cock fancy type deluxe heavy duty 12.7mm dia Indian make 400 grams

Supplying and fixing towel rod (CP) of 24'' long and 3/4'' dia

Supply and Fixing 12.7mm NP two way Angle cock Indian make heavy duty

Supply and fixing 12.7mm dia NP pillar cock heavy duty 1st quality Indian make.(400 grams) Seiko/Senoir

Supply of SYMET BIB COCK (CAT.NO:121) Standard 15 mm size as per IS 9763-2000 with ISI mark male thread with deluxe handles,86 mm long and 102 mm high and 43mm breadth 12mm seat dia and replaceable washers,having approx. weight of 90gms.

S & F 12.7 x 88.9 CP fancy shower

SYMET 2 in 1 Faucet (1 mts. Tube) with hook ( Prayag make CAT.NO:187) as directed during execution.

Supply & fixing 31.75 mm dia PVC flexible waste pipe of 914.4 mm length of Ist quality

Supplying and fixing of BITW coat hanger of size 0.60 x 0.076 x 0.025 m including finishing smooth the teak wood reapers and polishing with two coats of French Polish over Bee waxing of approved quality and fixing the specified (CP or aluminium ) coat hooks of different sizes of required numbers at equal spacing as directed during execution and fixing the coat hangers to the walls including cost and conveyance of all materials like screws, nails etc( excluding cost of hooks and fixing charges).

Supply and Fixing of Premium make CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2" SDR 11 and SDR 13.5 pipes are made from identical CPVC compounds having the same physical Properties for Hot and Cold Water (IS 15778:2007).

54.00 mm OD pipe SDR - 13.50

41.30mm ODPipe - SDR 13.50

28.60 mm OD pipe SDR - 13.50

22.20 mm OD pipe SDR - 13.50

Supply of 50mm PPR Ball Valve conforming to DIN Standards 8077/8092

Supply of 25mm PPR Ball Valve conforming to DIN Standards 8077/8092

Supply of following work men, as and when required and as directed during execution of work.

.- do - Supply of Mason / Carpenter / Plumber / Painter - Semi skilled work men (2nd Class)

.- do - Supply of Unskilled work men - Man / Woman Mazdoor / Watchman