LOWERING LIFTING AND REPAIR MAINT OF SUBMERSIBLE PUMP MOTOR AND CENTRIFUGAL PUMPING DOZING PLANTCLEANING OF OVERHEAD TANK AND ALLIED WORKS OF WATER SUPPLY AT WEST PART UNDER GE E BAREILLY

Amount

Lifting/taking out defective submersible pump of any capacity alongwith column pipe of any size and submersible cable , dismantling the pump from motor, setting aside for repair /servicing / overhauling including lowering the pump set into borewell replacement of packing and nut bolts ( if required) and testing after the completion of repair works in the presence of GE/ Engr in charge .

Rewinding to submersible pump 50 HP of any make with super enameled copper winding wire PVC coated 2 mm thick as per taken out qty , Providing PVC separators , PVC sleeves & jointing compound complete all as specified and directed. Note :- Rewinding, replacement items will be measured and paid seprately under relevent item.If the same motor copper winding wiring burnt second time in the above CA Period, The contractor is responsible to paid and rewind the same at their own cost.

All as per item no 02 above but capacity 41 Hp

All as per item no 02 above but capacity 10/15Hp

Repair/Replacement of following parts of the submersible pump and motor for capacity 40/41/50 HP of original company as approved by Accepting officer. Make : KSB, Crompton,Kirlosker Thrust bearing plate made out of carbon for submersible motor

Gun metal bush for submersible motor

Shaft sleeve made out of stainless steel for submersible motor

Clamp stud for submersible motor

Rotor balancing of submersible motor

Shaft grinding of submersible motor

GM Neck Ring for submersible pump

Stainless steel sleeve for submersible pump

Stainless steel pump shaft for submersible pump

Stainless steel impeller for submersible pump

Cast iron bowl for submersible pump

Rubber bush for submersible pump

M&L for ,Painting to pipe of pump house rising mains hydrants, sluice valves, pipe, fittings, NRV, discharge head etc after cleaning, scrapping and making the surfaces free from rust of main externally and painting with two coats synthetic enamelled paint in black/ blue/ red including marking/ writing on pipe etc complete as specified and directed

S&F in repair electric shock treatment chart coloured of size approximetely 3 ft x 2 ft & 6 mm thick plywood with teak wood frame including covered with plastic laminated sheet complete all as specified and directed.

S&F in repair machinary maintenance chart coloured of size approximately 3 ft x 2 ft & 6 mm thick plywood with teak wood frame including covered with plastic laminated sheet complete all as specified and directed.

M&L for trimming vegetation or small inequalities clearing all grass vegetation, saplings, shrubs, brushwood, roots, and tree of surroundings area up to 500 sq mtr including cleaning and removing rubbish upto a distance of 50 mtr outside the periphery of the area under clearance of water supply installations complete all as specified and as directed.Note-trimming will be done two times during contrct period at all installations of water supply. etc complete as specified and directed

S&F in repair for Aviation light on OH tank 18/21 mtrs staging (on top of OH tank) with all fittings,fixtures,and accessories including 2.5 sqmm wire Three core in 20 mm PVC conduit from light to connection points ,including 2-way MCB DB with isolator (10 Amp )capacity complete all as specified and directed.

M&L for installation of electronic Automatic level controller including probe unit ,five stage magnetic sensor concealed in S S tube of required length,controlling box including systems incorporated with stage signal,high & low alarm,pump automation as directed (Model ALC Mark-I) capable to one tank from one pump complete all as specified and directed

M&L for laying in ground Wire from probe unit to controller of 10 pair PVC copper conductor (0.5 sqmm)all as specified and directed(Note:-this item shall be measured in accordance with the quantity required for item no. 05 ,besides shall also be measured as required in existing level indicators) etc complete as specified and directed

S&F in repair for glow sign board (box type) LED of required size 600 x 600 mm made out of MS sheet of suitable size with sheet fixed on front and quality marked with details of Pump House etc on front and rear with different colours including provision of LED power- fittings & fixtures in equal distance to illuminate board including connections with 2.5 sqmm single core stranded copper conductor cable and writing with 10 mm size letters as specified and directed .

Supply & fix in repair 1100 volts grade heavy duty cable PVC insulated aluminum conductor screenedserved with inner sheathing of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4mm GI suspension wire , one twin core cables flat or circular of size 10 Sqmm.etc complete all as specified and directed .

S&F in repair Off load change over switch 200 Amp 4pole 415 Volt, .etc complete all as specified and directed

Supply and fix in repair energy saving and environemntal friendly long life versatile pressure die-cast aluminium IP-65 roadway luminaire 72 W LED fitting with high power LEDs light source and electronic driver . etc complete as specified and directed

S& F in replacement new generation post top energy saving environment friendly, long aesthetically designed with symmetrical light distribution spun aluminium landscape luminaire with power LED,s of 35 Watt as light source of 35 Watt suitable for pole dia 76 mm of complete all as specified and directed

S & F in replacement of street light brackets 40 mm bore GI pipe medicum grade upto 1.5 mtr long bend to shape including flat iron clamps and sutable nuts and bolts .etc complete all as specified and directed

Material and labour for replacement of PVC insulated single core multistranded copper cable of size 1.5 sq mm unsheathed 1100 volts grade drawn through conduit / cassing capping on surface / pole /wall concealed and making good of disturbed surface including taking down unserviceable wire .etc complete all as specified and directed

S&F Bldg Security light energy efficient 1X20 Watt LED 6K Endura cityliner leaf (with Toughned glass) die cast aluminium and fixing arrangement of fitting including 1 mtr 35/50mm GI 90 degree bend pipe complete all as specified (Make: Havells cat No; LHETBXU7PA6S025 equivalent to Philips/Bajaj /CG)

M&L for Earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm buried directly in ground (earth pi n ot less than 2.25 Mtr b elow normal ground level) connected to galvanized earth lead strip of size 25mm x 4 mm by means of bolts, buts, check nuts and washers of galvanized iro n on steel including 40 mm bore light grade GI tubing for protection of earth lead, MS sheet m etal funnel with wire mesh, watering pipe medium grade 20 mm dia, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type 1.50 mm thick precast RCC (1:2:4) type B1 pit cover reinfored with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar including aluminium strip of size 25 mm x 3 mm for extension of earth lead and necessary excavation, earth work, in soil/loose soil and disposal of spolis to a distance n exc 50 metre and necessary connection and testing complete all as shown n electrical plate No. 3 and all as direted and specified.

Taking down the Unseviceable LT panel installed at PH and replacement with new one cpri approved with following parts including panel board Wall mounted LT panel board indoor type of size 1200 x 1200 x400 mm with sheet CRCA sheet of 2 mm thickness comprising of the following :- (a) 3 pole power contactor type ML 4 suitable for operation on,440 Volts ,AC, 50 Hz -03 Nos (b) over load protection relay with relay range 45-75A suitable for operation on 3 phase, 415 V -01 Nos (c) voltmeter three phase anologue type class 1 voltage range 0-500 V flush mounting 96x96mm (d) ammeter three phase anologue type 5A class 1 of range 0-200 A flush mounting 96x96mm inculding CT 200/5 (e) ( e) MCCB 125 A capacity 3 pole for 415V -01 Nos (f) Supply and fix in repair MCCB 200 A capacity 4 pole for 415V -01Nos (g) indicating lamp on all 3 phases R Y B -01 set (h) PVC insulated multistranded copper conductor single core cable 4 sq mm (Nominal cross sectional area) as per site requirement including suitable size of copper lugs etc all as specified and directed-01 Job (j) single phase preventer direct mounting type with relay range 28-40 A 230 Volts suitable for electric motor of water supply installation-01 No (k) Electronic timer type ST 100 suitable for operation on 240/360/415 volts 50 Hz for 3-10 Sec-01 Nos. (l) Painting complete panel board with one coat of silver inside and outside -01 Job

Supply & replacement of Contactor ML-3 ,suitable to operate 35-45 HP submersible pumping set Cat part No SS-90721 Make-L&T or equivalent to approved make as specified in CA.

Supply & replacement of Contactor ML-4 ,suitable to operate 50-60 HP submersible pumping set Cat part No SS-90910 Make-L&T or equivalent to approved make as specified in CA.

M&L for cleaning of RCC Over Head Tanks capacity 1 lakh gallon and removing and taking out sand, sludge and mud etc including disposal of the same at a distance not exceeding 100 mtrs from the tank,including two coats of whitewash on whole internal walls of OH Tank all as directed . NOTE:-All the safety equipments for workers working on OHT and U/G Sumps will be provided by the contactor.Cleaning of OH tank is in every 6 month or contracor is responsible to clean all OH tank two time in their contract at same cost quoted rate.

All as per item no 36 above but capacity 50000 gallon.

All as per item no 36 above but capacity 25000/35000 gallon.

Supply only Aquafit (Calcium based granular disinfectant for water treatment ,Packing in 45 KG ,plastic drums complete all as specified and directed .

M&L MCCB , 4 pole, 415 Volt, fixed type 125 to 160 amp with breaking capacity 36 Ka complete all as specified and directed.

M&L MCCB , 4 pole, 415 Volt, fixed type 160 to 200 amp with breaking capacity 35 kA complete all as specified and directed.

Repair and servicing of powder base vacuum type chloronome/dosing plant for smooth functioning including necessary spares as their own cost required for rectifying the defects to be included for smooth functioning the plants for the following plants :- Location :- Pump house No. 12,25,27,28,29,30,31,32,33,34,36,37,38,MH and swimming pool etc Note:- (i) For smooth functioning the complete spares plants and rewinding & repair of mixing motor has to concluded in the quoted rate. (ii) All testing equipments to be used in installations. (iii) Contractor should be well equiped with proper protection of chlorine gas and mask should be kept with all operators.

Taking out connection of Chlorine / Altoch dosing system , detecting fault and repair /replacement of unserviceable parts and refixing same after completion job and connecting dosing system and testing complete all as specified and directed. Make : Aquafit, Chloromax or eqvt. (NOTE; Spares parts shall be measured and paid separately as Supply only ) as under :

Supply only rotor assembly with bearing brackets and tolerance rings suitable for decree dosing pump complete all as specified and directed.

Supply only pump tube suitable for dosing pump complete all as specified and directed.

Supply only injectior assembly suitable for dosing pump complete all as specified and directed.

Supply only duckwill suitable for dosing pump complete all as specified

Supply only diaphragm assembly suitable for dosing pump complete all as specified

Supply only weighted suction line stainer suitable for dosing pump complete all as specified and directed.

Supply only PVC pipe as per existing size all as specified

Supply only caustic/Soda crystals/Soda Ash powder in 5 Kg vacuum packets complete all as specified and directed

Supply only Soda lime powder in 25 Kg vacuum packets complete all as specified and directed

Supply and fixing CI fittings for CI Bends, connecting pieces, bell mouth pieces, tapers, tee pieces of one end flanged and other end spigot or socket upto 150 mm dia complete all as specified and directed.

Supply only lead for fitting in CI pipe joints complete all as specified and directed

S&F in repairs electronic timer type ST 100 suitable for operation on 415 volts 50 Hz for 3-30 Sec all as specified and as directed.

S&F in repairs electronic timer type ET 100 suitable for operation on 415 volts 50 Hz for 3-10/30 Sec all as specified and as directed.

Supply only grass and weeds killer chemical of make Roundup all as specified and directed.

S&F rubber mat of size 1mtrx2mtrx12 mm at installation of etc complete as specified and directed

S&F pressure gauge of dial 30 to 60 suitable for fixing at 100/150 header mm pipe with all fiting andf fixtures etc complete as specified and directed

S&F mini motor protection relay for 35-51hp submersibble motores of make L&T all as specified amd directed.

Supply and fix in repair spare conntact kit for ML 3 contractor complete all as specified and directed .

Supply and fix in repair spare conntact kit for ML 4 contractor complete all as specified and directed .

S&F in replacement of PVC bib tap 15 mm.bore etc complete as specified and directed

M&L for dismantling of motor, 3 phase, 7.5 KW, taking out burnt winding wire from stator, cleaning all slots properly, repair of pump/rewinding the motor with proper guage of super enamelled winding wire and varnishing properly including baking and providing insulation and packing properly re-assembling the motor with pump and installed at its proper position and testing the same including connection plate etc complete as specified and directed.

S&F in replacement MS ERW column pipe screwed 150 mm nominal bore having wall thickness not less than 7.11 mm electric resistance welded with MS flanged 16 mm thick heavy duty confirming to IS 6392 incl 2 mm thick rubber sheet and steel nuts and bolts 10 mm long with washer. etc complete as specified and directed

M&L for dismantling of non clog type centrifugal pump set of capacity 12.5hp either fixed or floor or on trolley mounred and taling out unsv spares and performin following operation to complete the task-: Rewinding of the motor centrifugal pumping set with insulated copper winding including sleeves as per original approved and replacement of worn out parts including griding of parts testing & transport charges complete all as specified and directed. replacement of motor bearing with lock nut -02 Nos Repalcement of fan motor-01 No Replacement of star coupling set with rubber-01 Each

Take the water sample from the bore well at ph no. 12,25,27,28,29,30,31,32,33,34,36,37,38, MH PH and two consumer end and send it for physical/Chemical/Bateriological test from any recognised govt agency (two times in contract period) and provide its report to Engr in charge.

S& F in replacement submersible pump / motor electric driven 415 Volts , TP suitable for 200/250 mm bore well casing pipe size 200/250 mm supply complete of 41 HP all as specified and directed.

Supply fixing testing and commissioning submersible cable flat 16 sqmm 3 core PVC insulated and PVC sheathed with multi stranded copper conductor 1100 volts grade fixed to submersible motor column pipe using suitable size of clamps made out of stainless steel flat of size 20x2 mm with steel nuts bolts & washer foe every column pipe of 3 mtr lenght all as specified and directed.

Supply install in repair and commissioning of Granular chlorination dosing pump of high pressure single head gear motored adjustable dosing pump having output of 2 U.S. GPD to 40 U S GPD and adjustable high pressure of up to 100 PSI (7 kg/cm2)or more ,power input 230 V,50 HZ self priming with nonmetalic with connecting nuts ,ferrules and with all accessories including lead,tubing connection injection check valve complete all as specified and directed. Preparation tank(300 ltr) (i) Water inlet line (ii) Outlet with strainer (iii) Drain (iv) Overflow (v) Conical bottom for sludge deposition (vi) Pot hole with cover (viiLevel gauge (viii) Inspection port (ix) Agitator 120 watt 900 RPM single phase mounted with plastic shaft and impeller. Service Tank (100 ltr) (i) Water line inlet (ii) Dosing pump inlet arrangement (iii) Drain (iv) Overflow (v) Level gauge (vi) Inspection port make-:pearl filter/Briozing/Declibec/Aqufit. Note :- Tenderer may note that amount of credit will be deducted from the total amount arrived, at the time of Acceptance of contract

sunder and company

prabhave traders