HWPK/CIVIL/2022/405

Amount

Dismantling Asbestos cement roofing including ridges, hips, valleys and gutters etc. and stacking the material at civil colony store or dumping yard as directed by EIC at all height including all necessary arrangement, scaffolding etc. complete as per the specifications and as directed by EIC.

Providing and fixing colour coated corrugated galvalume profile sheets of TATA/JSW or equivalant make (Profile, Colour and shape as approved by the Engineer-incharge) of 0.60mm(TCT) total coated thickness (tolerance as per relevant IS code) with material yield strength 550 MPa, galvalume AZ-150 (zinc aluminium alloy coating nominal composition : 55% aluminium, 43.5% zinc & 1.5% silicon mass total of both sides) with regular modified polyester paint and coating of 20- 25 micron RMP on exposed surface including primer and 7-10 micron epoxy coating on unexposed surface including primer. The sheet should be supplied in single length as desired by Engineer-in-charge. The sheet shall be fixed using self drilling / self tapping screws with EPDM seal and washers of make- Coroshield/ durotuff / polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers( as per engineer in charge) including cutting to size and shape wherever required etc. complete as per the specifications and as directed by EIC. Note: 1. All screw should be sealed with silicon sealant. 2. Measurements will be given only for covered Roof area and over laps will not be measured or paid separately.

Providing and fixing Ridge cover of minimum 40 cm overall width, minimum TCT 0.60 mm thick galvalume sheet with sufficient longitudnal and side lapping as per specifications, fixing in place at all heights using polymer coated hot dip galvanized hex head self drilling and self tapping screws with sealing arrangement / polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers with all necessary accessories etc. complete as per drawing, specifications, manufacturer specifications and as directed by Engineer.

Providing and laying at all floors and levels vitrified floor tiles of 1st quality of H&R Jhonson /somany/Kajaria/Nitco/RAK India or other equivalent approved make in all colours, shades and patterns and of thickness as per manufacture's specifications, with water absorption less than 0.08% and conforming to IS: 15622, laid directly over existing floors/tiles using polymer cum cement based adhesive manufactured by Roffe construction – NSA (non skid adhesive) or M/s Ardex Endura chemicals– Gold star or other approved equivalent high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness or as needed as per site conditions in respect of flooring laid to line, level and required slope as directed and fixed over 12 mm thick backing cement mortar 1:3 in respect of skirting, close jointed and grouted with white cement based Tile Grout of approved make and matching shade with pigments to match the colour of the tiles, finished to level, line, slope and plumb including cutting of tiles, making openings/ cut out where necessary including wastage for odd shape of room and final cleaning of surfaces as required, curing, etc. complete all as per specification, relevent IS code & as directed by the EIC.

In flooring with tiles of approx. size 600 mm x 600 mm laid directly over existing flooring using tile on tile polymer cum cement based adhesive including wastage, hacking to the existing flooring, disposal of debris at disposal yard in colony etc. complete.

In Dado / skirting with tiles of size 600 x 100 mm laid over 12 mm thick CM 1:3 backing, jointed with cement slurry & grouted with pigment of matching shade & finishing the top of skirting etc. complete, including wastage, disposal of debris at disposal yard in colony etc. complete.

Providing and laying factory made chamfered edge 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as per the direction of Engineer-in-Charge. Note: Paver Block shall be approved by Engineer-in-charge.

Providing and laying in position plain cement concrete 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) including consolidation, finishing, curing etc. complete as per specifications including the cost Form work shuttering, centering, (but excluding cost of steel reinforcement) complete as per the specification and as directed by the Engineer.

Demolishing cement concrete slab, road manually/ by mechanical means including disposal of material within 3 km metres lead as per direction of Engineer - in - charge.

Demolishing brick work in cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 2Km lead as per direction of Engineer-in-charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter of area 3 sq. metres and below including chowkhats, architrave, holdfasts etc. complete and stacking at colony civil office store complete as per the specifications and as directed by EIC.

Providing and fixing up to floor five level precast cement concrete slab 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20mm nominal size) for drain cover, including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including cost of required Centering completeas per the specifications and as directed by EIC.

Providing and laying in position plain cement concrete 1:2:4 (1 Cement: 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) including consolidation, finishing, curing etc. complete as per specifications including the cost Form work shuttering, centering, (but excluding cost of steel reinforcement) complete as per the specification and as directed by the Engineer.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within within 2Km lead as per direction of Engineer-in-charge.

Plastering with 15 mm cement plaster in 1:4 mix (1 cement: 4 fine sand) at all heights including providing scaffolding, curing etc. complete as per specifications and as directed by Engineer in charge.

Providing and laying Anti skid Ceramic floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in all colours, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment, Curing etc., complete all as per the specifications and as directed by EIC.

Providing and fixing Ist quality ceramic rectified glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 15 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade, including cutting for openings, curing etc. complete as per the specifications and as directed by EIC.

Applying priming coat With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work including preparing surfaces, scaffolding, filling with putty wherever required & cleaning etc. complete all as per specifications & as directed by the Engineer-in-Charge.

Painting old steel/wood work/ plastered surface with two or more coats of synthetic enamel paint using 1st quality synthetic enamel paint of Asian Paints or equivalent including applying additional coats wherever required to achieve even shade and colour, including preparing surfaces, scaffolding, filling with putty wherever required & cleaning etc. complete all as per specifications & as directed by the Engineer-in-Charge.

Providing & laying TMT Reinforcement Steel bar of grade of Fe 500D or more for reinforced cement concrete at all levels including supplying, preparation of barbending schedules, cutting, bending, transporting, fixing, tieing in position with G.I binding wire, all labourcharges, cost of cover blocks in specified grade of concrete etc. complete as per specifications and drawings. Steel supplied by the contractor using TMT bars of specified grades of all sizes.

Labour cost for laying of old red stones in footpaths/Open area, in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), making joints with grooves (thickness of joints, except at curves shall not be more than 5 mm), including necessary levelling, dressing, providing and laying 100mm thick sand bedding, making drainage opening wherever required etc. complete as per direction of Engineer-in-charge. Note: 1. Old red stones required for laying will be provided by department at free of cost, however contractor has to make all necessary arrangement to fetch the material at site, therefore quoted rates shall be inclusive of loading, unloading, transportation etc. complete. Length and bredth of of finished pavement excluding kerbs shall be measured for payment.

Distempering with 1st quality acrylic washable distemper (ready mixed) of approved brand,manufacturer of required shade and colour two or more coats including applying additional coats wherever required to achieve even shade and colour, including prepartion of surface, filling the unever surfaces with J K or eqivailant make wall putty, sand papering, making the surface smooth and even etc. complete as per manufacturer’s specification, cleaning of distemper splashings and droppings from floors, doors & windows etc. complete and as directred by the Engineer.

Applying a coat of cement primer as per manufacturer’s specifications etc. and as directred by the Engineer.

Providing and applying white cement based putty of average thickness 1 mm, Birla white wall care putty over the plastered wall surface to prepare the surface even and smooth complete including applying additional coats wherever required to achieve evensurface, including preparing surfaces, scaffolding & cleaning etc. complete all as per specifications & as directed by the Engineer-in-Charge.

Removal of old white wash/colour wash by thoroughly scrapping using wire brush & other suitable tools and tackles, sand papering the entire wall surface completely exposing the bare wall, cleaning with fibre broom and washing entire surface with water, preparing the surface even and smooth including necessary repairs to patches, scratches, including necessary scaffolding etc. complete as per specifications and as directed by the Engineer.

VIKAS ENTERPRISES

M/S Singh Brothers