BEAUTIFICATION OF MAHUNAG TEMPLE COMPLEX IN TEHSIL KARSOG DISTT MANDI HP SUB HEAD CONSTRUCTION OF LANGAR HALL CUM SARAIN BHAWAN

Amount

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation, trenches, drains (Any width or square metre on plan), including dressing of sides and ramming of bottoms, lift upto any height, including getting out the excavated soil and disposal of surplus excavated soil as directed in all kinds of classification, of soils such as pick work, jumper work, blasting work saturated soils including chiseling or any other mixed variety of soils, dewatering and / or removal of slush and other incidentals within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Any loss to the public or private property during the course of excavation shall be the sole responsibility of the contractor which shall have to be duly compensated by him at his own cost in all cases.

Providing and laying, mechanically mixed and vibrated cement concrete 1:4:8 (one cement:four sand eight graded crushed stone aggregate 40 mm (forty millimeter) nominal size) including curing as required at site complete excluding the cost of form work but including all leads and lifts of materials in foundation and plinth including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying, mechanically mixed and vibrated cement concrete 1:5:10 (one cement:Five sand Ten graded crushed stone aggregate 40 mm (forty millimeter) nominal size) including curing as required at site complete excluding the cost of form work but including all leads and lifts of materials in foundation and plinth including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying M-25 grade of concrete with minimum cement contents of 400kg (four hundred kilogrames per cum )mechanically mixed and vibrated graded crushed stone aggregate 20mm nominal size and curing complete excluding the cost of form work and reinforcement for reinforced concrete work including carriage as required complete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Foundation ,footing basis of columns etc and mass concrete as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Walls any thickness (but not exceeding 0.10 m thickness (point ten meters thickness including attached pilasters, buttersses, plinth and string courses etc. From top of foundation up to all floor level complete in all respect including carriage as required complete in all respect in all leads & lift in all levels and other incidentals

Beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to all floor level, as per direction of the Engineer-in-charge including carriage of material with in all leads , lifts in all floor levels and other incidentals.

Providing from work with steel plates 3.15 mm (three decimal fifteen millimeter ) thick welded with angle iron in frame 30X30X5 mm (thirty into thirty into five millimeters )so as to give a fair finish including centering , shuttering ,strutting and propping etc. with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling & removal of same for in-situ reinforced concrete and plain concrete workincluding carriage as required complete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. in :

Foundation ,footing basis of columns etc. And mass concrete as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Flat surfaces, such as soffits of the suspended floors roofs , landing and the like floors etc. up to any thickness , all as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Beams cantilever girders and lintels side and soffits of beams, beams haunchings, cantilevers, bressumers and lintels any depth in all heights from floor as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Columns, pillars ,posts and struts square, rectangular or polygonal in plan as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc including carriage of material with in all leads ,lifts in all floor levels and other incidentals.

Form work in edges of slab and breaks in floor and walls under 20 cm wide as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing tor steel reinforcement TMT bar Fe 500 ISI make high yield strength for reinforced cement concrete work including bending ,binding and placing in position and cost of binding wire complete for all floors including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5(seven point five) in fooundation and plinth lin cement mortar 1:6 (one cement : six sand) including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5(seven point five) in superstructure above plinth level up to all floor level in all shapes and sizes in cement mortar 1:6 (one cement : six sand) including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level in cement mortar 1:4 (one cement: four sand)including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Random rubble masonry with hard stone of approved quailty in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded stone aggregate 20 mm nominal size) upto plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand) as required in all leads & lift in all levels including carriage and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. in :-

Providing Boulder Filling under floor including carriage as required complete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 18 mm(eighteen) milimetre thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. including carriage as required complete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. Granite stone shall be got approved from engineer incharge before use.

Providing edge moulding to 18 mm(eighteen) milimetre thick granite stone ,marble or kota stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing second class deodar wood work in frames of doors ,windows ,clerestory, windows and other frames wrought ,framed and fixed in position including carriage of material with in all leads , lifts and other incidentals,

Providing and fixing 40 mm thick (fourty mili metres) second class deodar wood glazed shutters for doors, windows and clerestory windows using 4 mm (four mili metre) thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws including carriage as required complete in all respect in all leads & lift in all levels and other incidentals

Providing and fixing 40mm (forty millimeters )thick wire gauge shutters for doors windows and clerestory windows, using galvanized MS wire gauge of IS gauge desigination 85 G with wire of dia 0.56mm including black enameled iron butt hinges with necessary screws of second class deodar wood including carriage of material with in all leads , lifts and other incidentals .

Providing and fixing ISI marked 35 mm thick including Stainless Steel butt hinges with necessary screws flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. ncluding carriage of material with in all leads , lifts and other incidentals .

Extra for providing lipping with 2nd class teak wood battens 25 mm (twenty-five milimetre) minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Glazing with glass pan 5 mm (five point five millimeters)thick plain glass panes with teak wood beading including carriage as required complete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing second class teak wood wooden moulded beading 50x20mm (fifty X twenty mili metre)to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete including carriage of material with in all leads , lifts and other incidentals

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc.Fixed to openings /wooden frames with rawl plugs screws including priming coat with approved steel primer including carriage as required complete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)including carriage of material with in all leads , lifts and other incidentals.

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws complete including carriage of material with in all leads , lifts and other incidentals

250x10mm (two hundred Fifty X Ten mili metres)

100x10mm (one hundred X Ten mili metres)

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc.

Providing and fixing bright finished brass handles with screws complete including carriage of material with in all leads , lifts and other incidentals .

100 mm (one hundred mili metres)

Providing and fixing bright finished brass hanging type floor door stopper, with necessary screws etc. complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete including carriage of material with in all leads , lifts and other incidentals .

Providing and fixing bright finished brass casement stays (straight peg type),with necessary screws etc.complete.200mm weighing not less than 240gms including carriage of material with in all leads , lifts and other incidentals .

Providing and fixing 50 cm (fifty centimetre) long bright finished brass kicking plate of size 100x3.15 mm, with necessary screws etc. complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required including carriage of material with in all leads , lifts and other incidentals.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works complete.

Providing and laying 5.5mm (five point five milimetre) thick Ceramic/Spartic glazed floor tiles of size 300x300 mm (three hundred X three hundred milimetre) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (one Cement : four Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete including carriage of material with in all leads ,lifts and other incidentals .

Providing and fixing 1st. quality ceramic glazed floor tiles of size 300x300 (three hundred into three hundred millimeters) conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete including carriage of material with in all leads , lifts and other incidentals.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge including carriage of material with in all leads , lifts and other incidentals .

Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying vitrified floor tiles 600x600mmx10mm thick with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete including carriage of material with in all leads and lifts and other incidentals .

Providing and laying Vitrified tiles 600x600x10mm thick , with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (one cement: three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete including carriage of material with in all leads,lifts and other incidentals.

Providing and fixing exterior Vitrified tiles of sizes 1200mmx200mm (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints and carriage of material with in all leads , lifts and other incidentals.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge including carriage of material with in all leads , lifts and other incidentals

Providing and fixing GRC unistone tile claddding of size as per architectural drawings in all colours and shades as approved by Engineer -in- charge over 12mm thick bed of cement mortor 1:3 (one cement: three coarse sand)and jointed with grey cement slurry @3.30kg /sqm complete in all respect including carriage of material with in all leads , lifts and other incidentals.

Providing and fixing 110mm dia (one hundred ten mili metre) (working pressure of 4.5 kg /sqcm) on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes including carriage of material with in all leads and lifts and other incidentals .

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories (working pressure of 4.5 kg /sqcm) for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

110mm bend (one hundred ten mili metres)

110mm shoe (one hundred ten mili metres)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm (fifty X fifty X fifty mili metres) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (one cement : four coarse sand) and making good the wall etc. complete.including carriage of material with in all leads and lifts and other incidentals .

110 mm diameter (one hundred ten mili metres)

6 mm(six millimeter)thick cement plaster to ceiling in cement mortar 1:3 (one cement :three sand as per direction of engineer-in- charge including carriage as required complete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

15 mm (fifteen millimeter) thick cement plaster in single coat on rough / fair side of brick /concrete/stone wall for interior plastering for all floors including arises internal rounded angles chafers and / or rounded angles chamfers and/ or rounded angles not exceeding 80mm (eighty millimeters )In girth and finished even and smooth in cement mortar 1:6 (one cement :six sand ) including carriage as required complete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and applying white cement based putty of average thickness 1 mm (one mili meter), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage as required complete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Distempering two coats with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 (fifty) grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. including carriage of material with In all leads , lifts in all floors and other incidentals completes as per direction and to the entire satisfaction of Engineer-in-Charge.

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture including carriage as required complete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture including carriage as required complete in all respect in all leads & lift in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of WC ,kitchen and the like consisting

1st course of applying cement slurry @4.40kg mixed with water proofing compound confirming to IS 2645 in recommended proportions including rounding of junctions of vertical and horizontal surfaces including carriage of material within all leads, lifts in all floors and other incidental.

2nd course of 20mm cement plaster 1:3(one cement:three sand) mixed with water proofing compound in recommended proportions including rounding of junctions of vertical and horizontal surfaces

3rd course of applying blown or residual bitumen applied hot at 1.7kg/sqm of area including carriage of material within all leads, lifts in all floors and other incidental.

4th course of 400 micron thick PVC sheet(overlaps at joints of PVC sheets shouldbe 100mm wide and pasted to each other with bitumen at 1.7kg/sqm) including carriage of material within all leads, lifts in all floors and other incidental.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) cera, hindware, parryware make with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) cera, hindware, parryware make with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china orissa pattern W.C. pan of size 580x440mm with integral type foot rests including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin cera, hindware or equivalent make of 430x260x350 mm( four hundred thirty X two hundred sixty X three hundred fifty milimeters)and 340x410x265 mm (three hundred forty X four hundred ten X two hundred sixty five milimeters) sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required One urinal basin with 5 ltr. white P.V.C automatic flushing cistern including carriage of material within all leads, lifts in all floors and other incidental.

Providing and fixing White Vitreous China Wash basin cera, hindware, parryware or equivalent make size 550x400 mm (five hundred fifty X four hundred mili meters)with a pair of 15 mm C.P. brass pillar taps wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing white vitreous china pedestal for wash basin cera, hindware or equivalent make completely recessed at the back for the reception of pipes and fittings. including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink 510x1040 mm( five hundred ten into One Thousand forty) milimetre bowl depth 225 ( two hundred twenty five ) as per IS:13983 with C.I. brackets and stainless steel plug 40 mm florty millimetre , including painting of fittings and brackets, cutting and making good the walls wherever required :including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 8 mm( eight millimetre) dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. Heavy duty jet quality and sample should be got approved from Engineer - in - charge before use. required :including carriage of material as required in all leads & lift in all levels and other incidentals

Providing and fixing 32mm ( thirty Two millimetre) dia P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.including carriage of material as required in all leads & lift in all levels and other incidentals complete in all respect

Providing and fixing 100 mm CP Brass grating for gully trap. including carriage of material as required in all leads & lift in all levels and other incidentals

Providing and fixing 600x450 six hundred into ( four hundred fifty) mm beveled edge mirror of heavy dutysuperior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete

Providing and fixing 600x120x5 mm ( six hundred into one hundred twenty into five millimetre) heavy duty of approved quality glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm ( forty millimetre )long screws, rawl plugs etc., complete.

Providing and fixing heavy duty toilet paper holder : C.P. brass complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately).

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore .

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms 15 mm nominal bore. complete including carriage of material with all leads and lifts.

Providing and fixing 15 mm ( fifteen millimetre ) nominal bore C.P. brass long body bib cock of jaquar/jal/ess ess make of approved quality conforming to IS standareds and weighing not less than 690 gms. The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 15 mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm ( fifteen millimetre ) nominal bore of jaquar/jal/ess ess make. The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) ( fifteen millimetre into fitty millimetre )of approved make and quality as per direction of Engineer-in-charge. The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.The sample quality & series should be got approved from Engineer - in - charge before use.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside dimensions 455x610 mm ( four hundred fifty five into six hundred ten millimetre )and 45 cm forty five five centimetre deep for single pipe line :

Inside dimensions 500x700 mm *( five hundred into seven hundred millimetre )and 45 cm deep for pipe line with one or two inlets :

Inside dimensions 600x 850 mm ( six hundred into eight hundred fifty millimetre ) and 45 cm deep for pipe line with three or more inlets :

Extra for depth beyond 45 cm of brick masonry chamber.

For 455x610mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

For 500x700 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

For 600x850 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

15 mm ( fifeen millimetre )nominal outer dia Pipes

20mm (twenty millimetre )nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge

15 mm ( fifteen millimetre ) nominal outer dia Pipes

20mm ( twenty millimetre ) nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement,trenching, refilling and testing of joints the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge

15 mm ( ffiteen millimetre ) nominal outer dia Pipes

20mm ( twenty millimetre ) nominal outer dia Pipes

Providing and fixing PPR Unions 20 mm ( twenty millimetre )

Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm ( fifty into five millimetre ) flat of specified shape, projecting 75 mm ( seventy five millimetre )outside the wall surface and fixed on wall with 4nos, 6mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x1.6 mm Thirty millimetre into (one point six millimetre) galvanised M.S. flats of specified shape and of total length 420 ( four hundred twenty )mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe. Total bracket length 580 mm( five hundred eigthy millimetre ) of approved shape and design (for single 100 mm dia pipe)

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

15 mm ( fifeen millimetre )nominal outer dia Pipes

20mm ( twenty millimetre ) nominal outer dia Pipes

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive cost of cutting and making good the walls and floors complete

110mmx90mm (one hundred ten into ninety millmetre)

110mmx75mm ( one hundred ten into seventy five millimetre)

Providing and fixing 6 Kgf pvc Poly plast sewerage pipe of working pressure not less than 4.5 kg per square metre (Four point five kilogramme per square metre) including filling the joints with approved adhesive complete.

110 mm dia ( one hundred ten millimetre )

75 mm dia ( seventy Five millimetre )

Providing and fixing PVC single equal branch with oval access door ISI marked insertion rubber washer 3mm thick boalts and nuts complete including fixing with approved adhesive complete

110 mm dia ( one hundred ten millimetre )

75 mm dia ( seventy Five millimetre )

Proving and fixing PVC door bend with oval access door insertion rubber washer 3mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete

110 mm dia ( one hundred ten millimetre )

75 mm dia ( seventy Five millimetre )

Providing and fixing PVC collars ISI marked including fixingwith approved adhesive etc. complete

110 mm dia ( one hundred ten millimetre )

75 mm dia ( seventy Five millimetre )

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete

110 mm dia ( one hundred ten millimetre )

75 mm dia ( seventy Five millimetre )

Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixd to wooden cleats with C.P. Brass screws complete.

Providing and fixing C.P. Brass towel rail of size 600mmx20mm complete with C.P. Brass brackets fixed to wooden plugs with CP brass screws complete.

DALIP SINGH VERMA

SOM KRISHAN GOVT CONTRACTOR