REPAIR AND MAINTENANCE OF INTERNAL ELECTRIFICATION FITTING AND FIXTURES OF OTM ACCN AT NORTH COMPLEX UNDER GE IMA DEHRADUN

Amount

S & F sub main wiring with PVC insulated unsheathed FRLSH cable 1100 Volt grade, with multi stranded copper conductor drawing in and including rigid PVC conduit in concealed / surface as required at site including one run PVC insulated unsheathed cable with multi stranded copper conductor colour code as a earth continuity and connected upto DB including taking down old unsv submain wiring of following sizes complete all as specified and directed. Make of wire:Havells/ Polyacab /Anchor Make of conduit: AKG Plastic Pvt Ltd./Bhagwati Plastic & Agriculture industry /Polycab Note:Two/Four run of single core PVC cable with one run of earth conductor & condiut shall be measured as one unit. (ii) The quoted rates shall be deemed to be inclusive for fixing the conduits to surface with using PVC rawl plugs etc. (iii) Phase sequence colour code must be follow i.e Phase( Red) and Neutral ( Black) In colour and for three Phase RYB For phase and black for neutral.

2 x 10 Sqmm + 1 x 10 Sqmm

2 x 6 Sqmm + 1 x 6 Sqmm

2 x 4Sqmm + 1 x 4 Sqmm

2 x 2.5Sqmm + 1 x 2.5 Sqmm

4 x 6Sqmm + 1 x 6 Sqmm

4 x 10 Sqmm+ 1 x 10 Sqmm

S & F Distribution boards epoxy powder coated TP & N (VTPN MCCB DB) fabricated from minimum 1.6 mm thick CRCA sheet and fixed/ flush to wall and suitable for universal mounting with 250 Amps fully insulated copper Bus Bar for each phase and 02 neutral shrouded bar ,2 earth bar and cable tie for cable management with reversible door for IP-43 DB,S protection,415 volt flush to wall including 01 Nos 160 Amps MCCB FP as incomer and 12/24 SP MCBs or 4 / 8 TP MCBs as per site requirement (or any combination of SP/TP MCBs) outgoings of following capacity including taking down old unsv MCCB DB,s complete all as directed. Make :Havells/Indo Asian/HPL

4 Way VTPN DB (FP MCCB +12 MCB,C).

8 WAY VTPN DB TP&N DB(FP MCCB +24 MCB,s)

S & F in repairs MCCB ,4 pole ICS=100% ICU at 415 volts with rupturing capacity 18 KA with thermal-magnetic release and adjustable overload setting . The MCCB shall have a Mechanical life = 40000 operations & Electrical life = 8000 operations of following capacity complete all as directed. Make: Havells/Indo Asian/HPL

S & F in repairs MCB SP complying to IS/IEC 60898, 240 volts 'C' Curve 10 KA with energy limiting class 3. The MCB shall have 50% lower watt loss as required by IS/IEC 60898 from 6A to 63A . The mcb shall have the unique property of di-electric strength, arc resistance, insulation, flame retardancy and temperature resistance, including connection with suitable size copper lugs, The MCB shall give visible flag indication when MCB trips on Short Circuit Fault. The MCB shall have safety shutter to avoid any wrong insertion of cable. The MCB shall have the termination capacity of 35 Sq mm. The MCB shall have electrical life 20,000 operations up to 32A and 12,000 operation up to 63A including connection with suitable size copper lugs complete all as directed of following capacity:- Make: Havells/Indo Asian/HPL

MCB SP6 to 32 Amp.240 volts

MCB SP 40 to 63 AMPS 240 volts

MCB SPN 6 to 32 Amps 240 volts

MCB SPN 40 to 63 Amps 240 volts

S & F in repairs sheet metal enclosure, single pole and neutral with two pin and earth plug and socket with and including one single pole MCB 20 Amps, , complying to IS/IEC 60898, 240 volts 'C' Curve 10 KA with energy limiting class 3. The MCB shall have 50% lower watt loss as required by IS/IEC 60898 from 6A to 63A . The mcb shall have the unique property of di-electric strength, arc resistance, insulation, flame retardancy and temperature resistance, including connection with suitable size copper lugs, The MCB shall give visible flag indication when MCB trips on Short Circuit Fault. The MCB shall have safety shutter to avoid any wrong insertion of cable. The MCB shall have the termination capacity of 35 Sq mm. The MCB shall have electrical life 20,000 operations up to 32A and 12,000 operation up to 63A including connection with suitable size copper lugs complete all as directed. Make: Havells/Indian Asian/HPL

S & F in repairs MCB DB complying with IEC 61439 -1 & 3., sheet metal enclosures double door Including 01 x 40 to 63 A SPN MCB as incoming and MCB SP 6 to 32A as out going as per way of DB.The DBs should be supplied with tin platted insulated copper bus bar rated for 100A. 240 volts 2 in 1 shutter (Metal Door) with IK09 type with blanking plates where required and IP 43 degree protection, the DB door should be hinged type and possible to reversible at site.The DB door shall have overhang, to gel with wall properly.The DB shall be supplied with all insulated N. Bar riveted on Din channel frame and should not restrict cable entry from top or bottom.The DB shall have plastic knobs on shield to hold complete all as directed of following capacity . Make: Havells/Indo Asian/HPL

4 way SPN DB.

8 way SPN DB.

12way SPN DB

16 way SPN DB

S& F modular fitting /fixture including taking down old unsv fitting/fixture of following specification : Make: Anchor/Havells/Legrand

Fan regulator modular step type 120W 240 volts 2 module.

Modular switch single pole one way 6/10 Amp 240 volts.

Modular switch single pole one way16/ 20 Amp 240 volts .

Modular socket outlet 2/3 pin combined 6/10 Amp 240 volts.

Modular socket outlet 2/3 pin combined 16/ 20 Amp 240 volts.

Modular bell push flush type, 6 Amps240Volts.

S&F white modular cover plate with frame of following module complete including taking down old unsv modular cover plate with frame all as directed. Make: Anchor,Legrand, Havells

1Module

2Module

3Module

4Module

6Module

8 Module

12 Module

S&F modular metal flush box of following module complete including taking down old unsv modular metal flush box with frame all as directed. Make: Anchor, Legrand, Havells

1Module

2Module

3Module

4Module

6Module

8 Module

12 Module

S&F Bell push flush type, 5 Amps including taking down old unsv bell push complete all as directed. Make: Anchor Penta PC, Havells (Reo)/SSK

S&F in repair Bell AC 230 volts single pole complete all as directed. Make: Anchor Penta PC, Havells (Reo)/SSK

S&F ceiling rose, 63.5 mm dia, ISI marked, three terminal of polycarbonate/isolated body including taking down old unsv ceiling rose complete all as directed. Make: Anchor Penta PC, Havells (Reo)/SSK

S&F Electronic steppped type fan regulator 100 watt 230 volts AC 50 Hz including taking down old unsv fan regulator complete all as directed. Make:Anchor Penta PC, Havells (Reo)/SSK

S&F Batten holder, PVC/polycarbonate type with back plate suitable for batten fittings including taking down old unsv batten holder complete all as directed. Make: Anchor Penta PC, Havells (Reo)/SSK

S&F switch piano, flush type, single pole one way 6 Amp including taking down old unsv switch complete all as directed. Make: Anchor Penta PC, Havells (Reo)/SSK

S&F switch piano, flush type, single pole one way 16Amp including taking down old unsv switch complete all as directed. Make: Anchor Penta PC, Havells (Reo)/SSK

S&F socket out let, multipurpose, 2 in 1 5 pin, 6 Amp including taking down old unsv socket complete all as directed. Make: Anchor Penta PC, Havells (Reo)/SSK

S&F socket out let, multipurpose, 2 in 1 5 pin, 16 Amp with fuse and neon indicator including taking down old unsv socket complete all as directed. Make:Anchor Penta PC, Havells (Reo)/SSK

S&F Electronic step rotary type fan regulator 1000 watt 230 volts AC 50 Hz including taking down old unsv fan regulator complete all as directed. Make: Anchor Penta PC, Havells (Reo)/SSK

S &F Bakelite sheet cover 3 mm thick cut as required shape and size including brass screws and cup washer off following size for mounting swich, socket fan regulator etc including taking down existing unserviceable bakelite sheet cover complete all as directed. Make: Hylam, Woodlite

S & F 1100 volts grade heavy duty three core copper cable PVC insulated stranded, served with inner sheathing of PVC tape and overall PVC sheathed including taking down unserviceable complete all as directed. Make:Havells/ Polyacab /Anchor

S & F flexible cable 3 core 23/0.0076 multi stranded copper conductor white/ black colour code including taking down unserviceable complete all as directed. Make: :Havells/ Polyacab /Anchor

S&F Exhaust fan 200 mm sweep, 1200 RPM, ,made up of Sturdy Engineering Plastic complete ,voltage 230 Volts ,50 Hz, energy saving model single phase copper wound motor, white in colour complete with blade, box type louvers etc including taking down old unsv exhaust fan complete all as specified and directed. Make : Havells /Crompton /Orient

S & F in repair Circuit/submain wiring with single core FR-LSH PVC insulated copper multi stranded conductor cable drawing into existing PVC rigid conduit in surface/concealed as required, including taking down unserviceable existing wiring etc complete of following sizes as directed. Make: Havells/ Polyacab /Anchor

S & F pressed steel sunken terminal boxes 1.6 mm thick, 60 mm including brass screws and cup washer of following size for mounting switch, socket fan regulator etc including taking down existing the existing unserviceable sunken terminal boxes complete all as directed.

Material and labour for Earthing complete with galvanized iron earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test point & to main switch board and testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in cement mortar 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI light grade earth lead protection pipe etc complete all as specified and directed. Note: (i) Earth lead wire and its protection pipe upto and including 7.5 mtr only from the top of earth electrode are included under this item. (ii) Any joints in earth lead from earth electrode to test point shall not be allowed/permitted.

Supply and fix Rigid non metalic PVC conduit of , inclusive of boxes (junction/terminal)but inclusive of all tees,bend ,elbow reducers, bell mouth tube ends and fixing acessories such as couplers,lock,nut saddles,pipe hooks including taking down old unsv pvc conduit all as specified and directed. Make of conduit:AKG Plastic Pvt Ltd./Bhagwati Plastic & Agriculture industry /Polycab

40mm dia

32mm dia

25mm dia

20mm dia

Supply and fix PVC rectangular block white in colour for mounting Switch,Socket,fan regulator etc. with 3mm thick plastic laminated sheet cover of size s including taking down old unsv rectangular block all as directed.

100mmx100mm and 50mm deep

175mmx100mm and 50mm deep

Supply and fix PVC Casing Caping inclusive of all tees,bend ,elbow and fixing acessories including taking down old unsv pvc casing caping all as specified and directed. Make :- AKG Plastic Pvt Ltd./Polycab/Bhagwati & Agriculture Industries.

50X20 mm dia

38 X 20mm dia

32X 16 mm dia

25 X 16 mm dia

S & F energy saving LED Bulb 14 W, E-27 base,220v- 240v ,50 HZ,including taking down old unsv led bulb all as specified and directed.

S & F Bulb LED 5 W,MR-16,GU5.3 base,220v- 240v ,50 HZ including taking down old unsv led bulb all as specified and directed.

S & F sheet metal enclosure, Triple pole and neutral with three pin and earth plug and socket with and including one triple pole MCB 32 Amps, 240 volts,10 KA , including taking down old unsv sheet metal enclosure complete all as directed. Make:- Havells/Indo Asian/HPL.

S & F three Phase electronic meter temper proof LCD display with polycarbonted cover 415 volt ,10 A to 60 Amps ,accuracy class-I, 50 Hz ,confirming to IS 13779,IP-54 with parameter to show data time ,current reading ,load PF ,voltage and KWH including taking down unserviceable meter complete all as directed. Make: HPL, L&T, Secure.

Supply and fix Exhaust fan 250 mm sweep, 1200 RPM, ,made up of Sturdy Engineering Plastic complete ,voltage 230 Volts ,50 Hz, energy saving model single phase copper wound motor, white in colour complete with blade, box type louvers etc including taking down old unsv exhaust fan complete all as specified and directed. Make :- Orient/Havells /Crompton

S & F in repairs wall mounted Fan 400mm sweep ,2100 RPM high speed and 105CMM Air Delivery,strudy base and thermal overload protection ,voltage 230 Volts ,50 Hz, energy saving model single phase copper wound motor, white in colour complete with blade, etc including taking down old unsv wall mounted fan complete all as specified and directed. Make : Orient/Havells/Crompton

Material and labour for point wiring with PVC insulated and unsheathed electric able 1100 volts grade single core FRLSH having multi stranded copper conductor of 1.5 sq mm nominal cross sectional area drawn in and including concealed non metallic rigid PVC conduit not less than 25 mm dia with all fitting and fixing accessories and 1.5 sq mm PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxes 1.6 mm thick, 60 mm deep of required size factory made for mounting switch, regulators etc with and including 3 mm thick plastic hylam laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside for mounting switches, sockets etc complete including taking down carefully existing aluminum/copper surface/concealed point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, holdersfor the following. Make of wire:Havells/ Polyacab /Anchor Make of conduit: AKG Plastic Pvt Ltd./Bhagwati Plastic & Agriculture industry /Polycab

One light point controlled by one, one way 6 Amp switch

One fan/exhaust fan point controlled by one, one way 6 Amp switch

One 5 pin 5/6 Amps socket outlet point on the same board .

One 5 pin 5/6 Amps socket outlet point on independent board.

One bell point controlled by one, one way 6 Amp button switch.

Description all as per item No 36 here in before but point wiring with 4 Sq mm multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 4 Sq mm PVC insulated multistranded copper conductor cable as continous earth wire.

Description all as per iten No 36 here-in-before but point wiring in casing caping /PVC Conduit as per site requirement complete all as specified and directed by Engr-In- Charge for the following:-

One light point controlled by one, one way 6 Amp switch

One fan/exhaust fan point controlled by one, one way 6 Amp switch

One 5 pin 5/6 Amps socket outlet point on the same board

One 5 pin 5/6 Amps socket outlet point on independent board

One bell point controlled by one, one way 6 Amp button switch.

Description all as per item No 36 here-in-before but point wiring casing caping /PVC Conduit as per site requirement with 4 Sq mm multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 4 Sqmm PVC insulated multi strand copper conductor cable as continous earth wire.

Description all as per iten No 36 here-in -before but mdular point wiring with in and including concealed non metallic rigid PVC conduit not less than 25 mm dia including modular inner and outer frame plate matching with surrounding with modular sunken steel boxes zinc oxide plated of suitable size for mounting modular switches, sockets,regulator etc complete for the following:- Note applicable for item No :36 to 40 (i) The quoted rates shall be deemed to be inclusive for cutting chasing in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing by applying one coat of putty and two coat of Distemper to the surface to match with the existing surface.The portion of point wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using PVC rawl plugs. (ii) Point wiring & earth wire shall be connected to each & every sunken box. (iii) All screws, fasteners, bolts, nuts & washer shall be cadmium plated & the cost of which is deemed to be included in the quoted unit rates. (iii) 1 x 5 Amps Independent board in one circuit of 1.5 sqmm and 1 x 16 Amps Socket board in one circuit of 2.5 sqmm / 4 sqmm be made. (iv) Wiring insulation test result sheet after or before carryng out the internal wiring must be recorded by contractor and the rate for the same deemed to be inclusive in the quoted rate. (v) Inventory of accn for wiring and fitting and fixture shall be prepared by contractor and submited to the dept after completion of wiring work for check and record and the rate for the same deemed to be inclusive in the quoted rate. (vi) IMA consiting Haritage bunlow/office accn which are very big in length and breadthwhere the point wiring circuit may exceeds in its standard length. Hence the contractor must visit the site before quoting the rate of wiring.

One light point controlled by one, one way 6 Amp modular switch.

One fan/exhaust fan point controlled by one, one way 6 Amp modular switch.

One 5 pin 5/6 Amps socket outlet point on the same board

One 5 pin 5/6 Amps socket outlet point on independent board

One bell point controlled by one, one way 6 Amp modular switch.

Description all as per item 40 here in before but point wiring with 4 sq mm multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 4 sq mm PVC insulated multistranded copper conductor cable as continous earth wire.

S & F switch piano, flush type, single pole one way, 5/10Amp complete all as directed. Make : Anchor Penta PC, Havells (Reo)/SSK

S & F switch piano, flush type, single pole one way, 15/20 Amp complete all as directed. Make: Anchor Penta PC, Havells (Reo)/SSK

S & F socket outlet, multipurpose, 2 in 1 5 pin, 5/10 Amp complete all as directed. Make:Anchor Penta PC, Havells (Reo)/SSK

S & F socket outlet, multipurpose, 2 in 1 5 pin, 15 /20Amp complete all as directed. Make: Anchor Penta PC, Havells (Reo)/SSK

S & F for Electronic step type fan regulator 100 watt 230 volts AC 50 Hz complete all as directed. Make: Anchor Penta PC, Havells (Reo)/SSK

S & F Bell AC 230 volts single pole complete all as directed. Make: Anchor Penta PC, Havells (Reo)/SSK

S & F Bell push flush type, 5 Amps complete all as directed. Make: Anchor Penta PC, Havells (Reo)/SSK

S & F Modular switch single pole one way 6/10 Amp complete all as directed. Make: Anchor, Legrand, Crabtree (Havells)

S & F for Modular switch single pole one way 16 /20Amp complete all as directed. Make: Anchor, Legrand, Crabtree (Havells)

S & F Modular socket outlet 2/3 pin combined 6/10 Amp 240 volts complete all as directed. Make: Anchor, Legrand, Crabtree (Havells)

S & F Modular socket outlet 2/3 pin combined 16/20 Amp 240 volts complete all as directed. Make: Anchor, Legrand, Crabtree (Havells)

S & F Modular bell push flush type, 5 Amps complete all as directed. Make: Anchor, Legrand, Crabtree (Havells)

S & F fan regulator modular step type 120W 240 volts 2 module type complete all as directed. Make: Anchor, Bajaj, Crompton, Havells

S&F ceiling rose, 63.5 mm dia, ISI marked, three terminal of polycarbonate/isolated body complete all as directed. Make: Anchor Penta PC, Havells (Reo)/SSK

S&F Batten holder, PVC/polycarbonate type with back plate including suitable for batten fittings complete all as directed. Make: Anchor Penta PC, Havells (Reo)/SSK

Supply and Fixing in repair LED Batten light fittings 4 feet on walls including connected the same with using PVC sheathed , insulated 3 core flexible 23/0.0076 copper cable including fixing arrangement for fixing the light fitting to ceiling rose all as conforming to the following parameters including taking down old unsv Light fitting: - (i) Lumens: -system lumen not less than 2500 lm (ii) Housing: - Highquality batten with extruded aluminium with Powder coated. (iii) IP Rating: - IP 20 (v) Mounting: - Wall Mounted (vi) Finish: - Polycarbonated diffuser (vii) Lamp: - High bright LED (viii) System Efficacy (lm/W) of the luminaries: - Not less than 124 lm/watt. (ix) Colour temperature (K): - Not less than 5700( COOL DAY LIGHT) (x) Color Rendering Index (CRI): - Not less than 80 (xi) Life: - Not less than 25000 Hrs of operation (xii) Optics: - Fully Diffused (xiii) Control gear: - inbuilt electronic driver, PF not less than 0.95 and THD less than 10 % with operating voltage 140-270V AC, 50 Hz (xiv) Surge protection: - inbuilt surge protection minimum 2.5 KV (xv) Heat Shink: - As per OEM's design Make: - Philips/Crompton/Havells/Eveready

Supply and Fixing LED Batten light fittings 2 Feet on walls including including connected the same with using PVC sheathed , insulated 3 core flexible 23/0.0076 copper cable including fixing arrangement for fixing the light fitting to ceiling rose all as conforming to the following parameters including taking down old unsv Light fitting: - (i) Lumens: -System lumen not less than 1000 lm (ii) Housing: - High pressure die cast aluminium. (iii) IP Rating: - IP 20 (v) Mounting: - Wall Mounted (vi) Finish: - Polycarbonated diffuser (vii) Lamp: - High bright LED (viii) System Efficacy (lm/W) of the luminaries: - Not less than 100 lm/watt. (ix) Colour temperature (K): - Not less than 5700(COOL DAY LIGHT) (x) Color Rendering Index (CRI): - Not less than 80 (xi) Life: - Not less than 50000 Hrs of operation (xii) Optics: - Fully Diffused (xiii) Control gear: - inbuilt electronic driver, PF not less than 0.90 and THD less than 20 % with operating voltage 100-300V AC, 50 Hz (xiv) Surge protection: - inbuilt surge protection minimum 4 KV (xv) Heat Shink: - As per OEM's design Make: - Philips/Crompton/Havells/Eveready

Supply and Fixing LED Suspended Batten light fittings on walls including connected the same with using PVC sheathed , insulated 3 core flexible 23/0.0076 copper cable including fixing arrangement for fixing the light fitting to ceiling rose ,all as conforming to the following parameters including taking down old unsv Light fitting: - (i) Lumens: - System lumen not less than 4000 lm (ii) Housing: - Corrosion and impact rsistance batten with polycarbonated housing. (iii) IP Rating: - IP 20 (v) Mounting: - Wall Mounted (vi) Finish: - Polycarbonated diffuser (vii) Lamp: - High bright LED (viii) System Efficacy (lm/W) of the luminaries: - Not less than 100lm/watt. (ix) Colour temperature (K): - Not less than 6500 ( COOL DAY LIGHT) (x) Color Rendering Index (CRI): - Not less than 80 (xi) Life: - Not less than 25000 Hrs of operation (xii) Optics: - Fully Diffused (xiii) Control gear: - inbuilt electronic driver, PF not less than 0.90 and THD less than 10 % with operating voltage 140-270V AC, 50 Hz (xiv) Surge protection: - inbuilt surge protection minimum 4KV (xv) Heat Shink: - As per OEM's design Make: - Philips/Crompton/Havells/Eveready

Supply and Fixing LED Up Down twin glow 20W + 20W Batten light fittings on walls including connected the same with using PVC sheathed , insulated 3 core flexible 23/0.0076 copper cable including fixing arrangement for fixing the light fitting to ceiling rose , all as conforming to the following parameters including taking down old unsv Light fitting: - (i) Lumens: - System lumen not less than 2000 lm on each side (ii) Housing: - High pressure die cast aluminium. (iii) IP Rating: - IP 20 (v) Mounting: - Wall Mounted (vi) Finish: - Polycarbonated diffuser (vii) Lamp: - High bright LED (viii) System Efficacy (lm/W) of the luminaries: - Not less than 100 lm/watt. (ix) Colour temperature (K): - Not less than 6500 on Down Side & 3000K on Up Side( Cool Day and Warm white Light) (x) Color Rendering Index (CRI): - Not less than 80 (xi) Life: - Not less than 35000 Hrs of operation (xii) Optics: - Fully Diffused (xiii) Control gear: - inbuilt electronic driver, PF not less than 0.90 and THD less than 20 % with operating voltage 160-360V AC, 50 Hz (xiv) Surge protection: - inbuilt surge protection minimum 2.5 KV (xv) Heat Shink: - As per OEM's design Make: - Philips/Crompton/Havells/Eveready.

Supply and Fixing LED 1 x 1 feet Surface/Recess Mounted light fittings including connected the same with using PVC sheathed , insulated 3 core flexible 23/0.0076 copper cable including fixing arrangement for fixing the light fitting to ceiling rose all as conforming to the following parameters including taking down old unsv Light fitting: - (i) Lumens: - System lumen not less than 1800 lm. (ii) Housing: - CRCA sheet with powder coating (iii) IP Rating: - IP 20 (v) Mounting: - Surface /Recess Mounted (vi) Finish: - Opal PMMA Diffuser (vii) Lamp: - High bright LED (viii) System Efficacy (lm/W) of the luminaries: - Not less than 100 lm/watt. (ix) Colour temperature (K): - Not less than 6500( Cool day white /warm white ) (x) Color Rendering Index (CRI): - Not less than 80 (xi) Life: - Not less than 25000 Hrs of operation (xii) Optics: - Fully Diffused (xiii) Control gear: - inbuilt electronic driver, PF not less than 0.90 and THD less than 10 % with operating voltage 140-27V AC, 50 Hz (xiv) Surge protection: - inbuilt surge protection minimum 2.5 KV (xv) Heat Shink: - As per OEM's design Make: - PHILIPS /Crompton/Havells/Eveready

Supply and Fixing LED street/Security light fittings on poles/Wall by providing GI bracket of suitable size including connected the same with using PVC sheathed , insulated 3 core flexible 23/0.0076 copper cable including fixing arrangement for fixing the light fitting to ceiling rose all as conforming to the following parameters including taking down old unsv Light fitting : - (i) Lumens: - System lumen not less than 3000 lm (ii) Housing: - Single Piece High pressure die cast aluminium with TOP opening . (iii) IP Rating & IK Rating: - IP 66 & IK07 (iv) Front cover: - Polycarbonated Cover for More protection (v) Mounting: - Suitable for pole mounting. (vi) Finish: - Epoxy powder coated with any additional treatment for smooth and anti corrosive finish. (vii) Lamp: - High bright LED with Lens (viii) System Efficacy (lm/W) of the luminaries: - Not less than 110 lm/watt. (ix) Colour temperature (K): - Not less than 5700 (x) Color Rendering Index (CRI): - Not less than 70 (xi) Life: - Not less than 50000 Hrs of operation @ Ta 35*C (xii) Optics: - Spread (Beam angle along the driveway) - 120°, Through (Beam angle across the driveway)- 60°, Beam pattarn- Asymmetrical driveway. (xiii) Control gear: - inbuilt electronic driver with 325V Auto Cut off Restart feature & 440V Phase to Phase protection till 8 hour, PF not less than 0.95 and THD less than 10% at full load with operating voltage 140-270V AC, 50 Hz. (xiv) Surge protection: - inbuilt surge protection minimum 4KV. (xv) Heat Shink: - As per OEM's design Make: - PHILIPS /Crompton/Havells/Eveready

Supply and Fixing LED 2x2 Recessed/Surface Mounted fittings including connected the same with using PVC sheathed , insulated 3 core flexible 23/0.0076 copper cable including fixing arrangement for fixing the light fitting to ceiling rose including taking down old unsv recess mounted fitting all as conforming to the following parameters: - (i) Lumens: - System lumen not less than 4000lm/ (ii) Housing: - Single Piece CRCA body (iii) IP Rating & IK Rating: - IP 20 & IK20 (iv) Front cover: - Polycarbonated Cover for More protection (v) Mounting: - Ceiling/ Recess Mounted . (vi) Finish: - Epoxy powder coated with any additional treatment for smooth and anti corrosive finish. (vii) Lamp: - High bright LED with Lens (viii) System Efficacy (lm/W) of the luminaries: - Not less than 110 lm/watt or 36 watt.. (ix) Colour temperature (K): - Not less than 6500( Cool day white ) (x) Color Rendering Index (CRI): - Not less than 80 (xi) Life: - Not less than 20000 Hrs of operation @ Ta 35*C (xii) Optics: - Spread (Beam angle along the driveway) - 120°, Through (Beam angle across the driveway)- 60°, Beam pattarn- Asymmetrical driveway. (xiii) Control gear: - inbuilt electronic driver with 325V Auto Cut off Restart feature, PF not less than 0.95 and THD less than 10% at full load with operating voltage 140-270V AC, 50 Hz. (xiv) Surge protection: - inbuilt surge protection minimum 3KV. (xv) Heat Shink: - As per OEM's design Make: - PHILIPS /Crompton /Havells/Eveready

Supply and Fixing LED Round/Square Surface/Recess Mounted Downlighter fittings and connected the same with using PVC sheathed , insulated 3 core flexible 23/0.0076 copper cable including fixing arrangement for fixing the light fitting to ceiling rose including taking down old unsv LED down lighter all as conforming to the following parameters: - (i) Lumens: - System lumen not less than 1800 lm (ii) Housing: - Single Piece body Die cast lluminium (iii) IP Rating & IK Rating: - IP 20 & IK20 (iv) Front cover: - Polycarbonated Cover for More protection (v) Mounting: - On ceiling/Recess Mounted (vi) Finish: - Epoxy powder coated with any additional treatment for smooth and anti corrosive finish. (vii) Lamp: - High bright LED (viii) System Efficacy (lm/W) of the luminaries: - Not less than 100 lm/watt. (ix) Colour temperature (K): - Not less than 6500( Cool day White /Warm Light ) (x) Color Rendering Index (CRI): - Not less than 80 (xi) Life: - Not less than 25000 Hrs of operation. (xii) Optics: -Diffused (xiii) Control gear: - PF not less than 0.90 and THD less than 20% at full load with operating voltage 140-270V AC, 50 Hz. (xiv) Surge protection: - inbuilt surge protection minimum 2.5KV. (xv) Heat Shink: - As per OEM's design Make: -PHILIPS /Crompton/Eveready

Supply and Fixing LED Round/Square Surface /Recess Mounted Mounted Downlighter fittings and connected the same with using PVC sheathed , insulated 3 core flexible 23/0.0076 copper cable including fixing arrangement for fixing the light fitting to ceiling rose including taking down old unsv down lighter all as conforming to the following parameters: - (i) Lumens: - System lumen not less than 1500 lm (ii) Housing: - Single Piece body (iii) IP Rating & IK Rating: - IP 20 & IK20 (iv) Front cover: - Polycarbonated Cover for More protection (v) Mounting: - On ceiling/Recess Mounted (vi) Finish: - Epoxy powder coated with any additional treatment for smooth and anti corrosive finish. (vii) Lamp: - High bright LED (viii) System Efficacy (lm/W) of the luminaries: - Not less than 100 lm/watt. (ix) Colour temperature (K): - Not less than 6500 Or not less 3000 (x) Color Rendering Index (CRI): - Not less than 80 (xi) Life: - Not less than 25000 Hrs of operation. (xii) Optics: -Diffused (xiii) Control gear: - PF not less than 0.90 and THD less than 20% at full load with operating voltage 140-270V AC, 50 Hz. (xiv) Surge protection: - inbuilt surge protection minimum 2.5 KV. (xv) Heat Shink: - As per OEM's design Make: -PHILIPS /Crompton/Havells/Eveready

Supply and Fixing LED Bulk Head fittings on surface /Ceiling and connected the same with using PVC sheathed , insulated 3 core flexible 23/0.0076 copper cable including fixing arrangement for fixing the light fitting to ceiling rose including taking down old unsv led bulk head all as conforming to the following parameters: - (i) Lumens: - System lumen not less than 1000 lm (ii) Housing: - Single Piece Aluminium pressure die cast body (iii) IP Rating & IK Rating: - IP66 & IK08 (iv) Front cover: - Polycarbonated Cover for More protection (v) Mounting: - On Surface / ceiling (vi) Finish: - Epoxy powder coated with any additional treatment for smooth and anti corrosive finish. (vii) Lamp: - High bright LED (viii) System Efficacy (lm/W) of the luminaries: - Not less than 100 lm/watt. (ix) Colour temperature (K): - Not less than 6500 (x) Color Rendering Index (CRI): - Not less than 80 (xi) Life: - Not less than 50000 Hrs of operation at Ta 45*C (xii) Optics: -Diffused (xiii) Control gear: - PF not less than 0.90 and THD less than 10% at full load with operating voltage 140-270V AC, 50 Hz. (xiv) Surge protection: - inbuilt surge protection minimum 2.5KV. (xv) Heat Shink: - As per OEM's design Make: - Philips /Crompton/Eveready

Supply and Fixing LED Flood Light fittings with complete fixing arrangemnets and connected the same with using PVC sheathed , insulated 3 core flexible 23/0.0076 copper cable including fixing arrangement for fixing the light fitting to ceiling rose including taking down old unsv led flood light all as conforming to the following parameters: - (i) Lumens: - System lumen not less than 5000 lm (ii) Housing: - Single Piece Aluminium die cast body (iii) IP Rating & IK Rating: - IP66 & IK07 (iv) Front cover: - Toughened Glass Cover for More protection (v) Mounting: - With complete fixing arangement, (vi) Finish: - Epoxy powder coated with any additional treatment for smooth and anti corrosive finish. (vii) Lamp: - High bright LED (viii) System Efficacy (lm/W) of the luminaries: - Not less than 100 lm/watt. (ix) Colour temperature (K): - Not less than 6500 (x) Color Rendering Index (CRI) & SDCM: - Not less than 70, <5 (xi) Life: - Not less than 25000 Hrs of operation at Ta 45*C (xii) Optics: -Diffused (xiii) Control gear: - PF not less than 0.90 and THD less than 20% at full load with operating voltage 140-270V AC, 50 Hz. (xiv) Surge protection: - inbuilt surge protection minimum 10KV. (xv) Heat Shink: - As per OEM's design Make: - Philips /Crompton/Havells/Eveready

supply and Fixing LED Flood Light fittings with complete fixing arrangemnets and connected the same with using PVC sheathed , insulated 3 core flexible 23/0.0076 copper cable including fixing arrangement for fixing the light fitting to ceiling rose including taking down old unsv led flood light all as conforming to the following parameters: - (i) Lumens: - System lumen not less than 13800 lm (ii) Housing: - Single Piece Aluminium pressure die cast body (iii) IP Rating & IK Rating: - IP66 & IK07 (iv) Front cover: - Toughened Glass for More protection (v) Mounting: - With complete fixing arangement, (vi) Finish: - Epoxy powder coated with any additional treatment for smooth and anti corrosive finish. (vii) Lamp: - High bright LED (viii) System Efficacy (lm/W) of the luminaries: - Not less than 110 lm/watt. (ix) Colour temperature (K): - Not less than 6500 (x) Color Rendering Index (CRI) & SDCM: - Not less than 70, <5 (xi) Life: - Not less than 50000 Hrs of operation at Ta 45*C (xii) Optics: -Diffused/Lens (xiii) Control gear: -Outcutt off @325V, 440V phase 2 phase protection, PF not less than 0.95 and THD less than 10% at full load with operating voltage 140-270V AC, 50 Hz. (xiv) Surge protection: - inbuilt surge protection minimum 4KV and 10 KV External SPD . (xv) Heat Shink: - As per OEM's design Make: - Philips /Crompton/Havells/Eveready

Supply and Fixing LED Post Top fittings,including taking down old unsv led post top fitting all as conforming to the following parameters: - (i) Lumens: - lumen not less than 2000 lm (ii) Housing: - Single Piece High pressure die cast aluminium. (iii) IP Rating & IK Rating: - IP 66 & IK10 (iv) Front cover: - Polycarbonated Cover for More protection (v) Mounting: - Suitable for pole mounting with bracket arm 40-50mm dia. (vi) Finish: - Epoxy powder coated with any additional treatment for smooth and anti corrosive finish. (vii) Lamp: - High bright LED with Lens (viii) System Efficacy (lm/W) of the luminaries: - Not less than 100 lm/watt. (ix) Colour temperature (K): - Not less than 5700 (x) Color Rendering Index (CRI): - Not less than 70 (xi) Life: - Not less than 20000 Hrs of operation @ Ta 35*C (xii) Optics: - Polycarbonate Diffuser (xiii) Control gear: - inbuilt electronic driver with 325V Auto Cut off Restart feature, PF not less than 0.95 and THD less than 10% at full load with operating voltage 140-270V AC, 50 Hz. (xiv) Surge protection: - inbuilt surge protection minimum 4KV. (xv) Heat Shink: - As per OEM's design Make: -PHILIPS /Crompton/Havells/Eveready Note:- applicable For Item No 57 to 69 (i) Contractor has to compulsorily submit the LM-79 and LM-80 and third party NABL accredited lab lumens test report conforming of technical spscifications and consolidated lab report for the offered LED has to be stractured in the same sequence.

Supply and fix LED inverter bulb 9 watt retrofit type works on AC Normal mode and DC supply in inverter mode with inbuilt battery back up of up to 4 hours, high efficiency high lumens output ,including taking down old unsv led bulb complete all as specified and directed. Make: Philips /Crompton /Eveready

Supply and fix exhaust fan ,steel body AC single Phase 230 Volts of size 300 mm sweep with blades and frames and louvers including taking down old unsv exhaust Fan. Make : Havells /Crompton /Bajaj/Eveready

S & F in repair MCB TPN complying to IS/IEC 60898, 240 volts 'B' Curve 10 KA with energy limiting class 3. The MCB shall have 50% lower watt loss as required by IS/IEC 60898 from 63A to 100A . The mcb shall have the unique property of di-electric strength, arc resistance, insulation, flame retardancy and temperature resistance, including connection with suitable size copper lugs, The MCB shall give visible flag indication when MCB trips on Short Circuit Fault. The MCB shall have safety shutter to avoid any wrong insertion of cable including connection with suitable size copper lugs complete all as directed of following capacity Make: Havells/Indo Asian/HPL.

MCB TPN 63 Amps, 415 volts

MCB TPN 100 Amps, 415 volts

M &L for preventive maint of Accn by checking loos connection by opening MCCB DB, MCB DB,Switch board,Sheet metal Enclosure and refresh all connection of switch board,MCB DBS,tightining the MCB,s and and refix the same position all as specified and directed. Note:- Maint of one Bldg shall be measured as one Job.

Taking down carefully existing surface /conceled light fitting from any height of any wattage /description by disconnecting the wire and set aside insafe custody for reuse and refixing in same postion after completion of work all as specified and directed.

G S CONSTRUCTIONS

Deven Associates

M/S S P BUILDERS

BK CONSTRUCTION

KRISHANA ELECTRIC WORKS