CA NO. CWE/AMB/NORTH-33 OF 2025-26 SPECIAL REPAIRS TO BLDG NO P-451(1-16 Qtr) IN GOVT MD ACCN (DEF CIV EMPLOYEES) AT TOPKHANA LINE UNDER GE (NORTH) AMBALA CANTT

Amount

Demolition Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including floor finishes complete all as specified and directed.

Providing and injecting emulsion for post constructionl anti termite treatment using chemical chloropyriphos 20 EC conforming to IS 8944 or lmidacloprid 30.50 SC conforming to IS 16131 concentrate along the external wall of building below concrete or masonry apron using chemical emulsion @ 2.25 litre per linear metre including drilling 12mm dia holes @ 300 mm apart and plugging holes with cement mortar 1:2 (1 Cement 2 Coarse sand) in apron complete all as specified and directed.

Providing and injecting chemical emulsion for post construction anti termite treatment using chemical chloropyriphos 20 EC conforming to IS 8944 or lmidacloprid 30.50 SC conforming to IS 16131 of soil under existing floors using chemical emulsion @ 1 Ltre per hole 300mm apart including drilling 12mm dia holes @ 300 mm apart and plugging holes with cement mortar 1:2 (1 Cement & 2 Coarse sand) to match the existing floor and making good the disturbed sufaces to match with the existing surface complete all as specified and directed.

Providing and injecting chemical emulsion for post constructional anti termite treatment at points of contact of wood work by using chemical chloropyriphos 20 EC conforming to IS 8944 or lmidacloprid 30.50 SC conforming to IS 16131 emulsion in oil or kerosene based solution @ 0.5 litre per hole by drilling 6mm dia holes at a downward angle of 45 degree @ 150mm centre to centre and sealing the same and making good the disturbed sufaces to match with the existing surface complete all as specified and directed.

Demolition of brick or stone masonary built in cement mortar incl all quoins, arches, pillar etc. complete all as specified and directed.

M&L brick work with sub class 'B' bricks old size, class 7.5 designation, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L brick work with sub class -B bricks, in half brick thick walls, built in cement moratr 1:4 straight or curved on plan to any radius complete all as specified and directed.

M&L Cement concrete in foundations, filling and mass concrete Type D2 1:5:10 using 40mm graded stone aggregate in sunken treatment complete all as specified and directed.

M&L Rendering 15 mm thick in CM (1:4) using water proofing compound as per manufacturer instruction as in sunken floor complete all as specified and directed. Vote : Water proofing compound will be measured and paid separately.

M&L for cutting grooves in brickwall,75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 and inserting water proofing felt/membrane as in sunken treatment complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

M&L for APP based polymeric membrane minimum weighing 3kg/Square Metre and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/Square Metre) laid by torch forced application over and including a coat of bitumen 85/25 grade applied hot @ 1.20 Kg/Square Metre over and including complete used in sunken portion complete all as specified and directed.

Dismantling floor,hearth or wall tilling including cement mortar bedding (but not backing ),removing serviceable tiles to store and rubbish off premises complete all as specified and directed.

M&L for PCC(1:3:6) type C1 using 20mm graded aggregate as in plinth protection of avg 50mm thick and finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

M&L for 25 mm thick Cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in sub base correction floors, surface fair finished and even and rough to receive floor finishes complete all as specified and directed.

M&L for Non - skid jointfree coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Square Metre but not exceeding 0.18 Square Metre, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per above item no 16 but as in skirting over and including 10 mm thick backing coat with cement mortar 1:4 complete all as specified and as directed .

M&L for glazed ceramic coloured tiles 450x300x7mm thk on vertical surfaces such as dados set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L rubber moulded coloured precast concrete interlocking paver block, any shape and size conforming to IS 15658-2006, ISI marked of 60 mm thickness, grade M-35 with grey cement and pigments over and including a layer of sand cushioning, 25 mm thick complete all as specified and directed.

M &L 75 mm thick PCC (1 :4:8) type d 2 using 40mm graded agg as in sub base of floor complete all as specified and directed.

Demolition of stone slabs of any description or any thickness laid bedded and pointed in any mortar in floors and walls approns etc. complete all as specified and directed.

M&L for Granite (of any type) slab 20 mm thick machine cut ,bedded and jointed with gray cement slurry and pointed with white cement as in floors/ cooking platform, with admixiture of pigment to match the shade of granite stone including grinding and polishing complete over and including 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for Granite (of any type) slab 20 mm thick machine cut , jointed with gray cement slurry and pointed with white cement as in vertical surfaces / dado / skirting with admixiture of pigment to match the shade of granite stone indluding grinding and polishing complete over and including 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

Rounding to edges of stone slabs one edge such as in steps & platforms etc complete all as specified and directed.

M & L machine cut Kota Stone slab as in flooring / landing/treads of stairs , 20-25 mm thick over and including 15mm thick cement screed bed in CM 1:4 , laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab and including rubbing and polishing and making grooves in treads ( as required ) complete all as specified and directed.

M & L machine cut Kota Stone slab as in skirting/ Risers of stairs , 20-25 mm thick over and including 10 mm thick rendering in CM 1:4 , laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab and including rubbing and polishing complete all as specified and directed.

M&L Machine cut green marble stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Machine cut green marble stone slab flooring 18-20mm thick as in skirting / dado over and including over and including 10 mm thick rendering in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L reinforced cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in slabs, suported on walls, beams and columns in floors, roofs, landings balconies canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L reinforced cement concrete M-25 type B1 (using 20mm graded stone aggregate) as in chajjas,Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels, balustrade, and the like complete all as specified and directed. .

M&L framework to chajjas , fins , louvers and fascia of horizontal or sloping , rough finished flat surfaces complete all as specified and directed.

M&L framework to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exc 200 mm thick horizontal or sloping , rough finished flat surfaces complete all as specified and directed

M&L framework for concrete flats teads exc 5 cm but n exc 10cm wide rough finished complete all as specified and directed.

S&F mild steel TMT bars 10mm dia and over, cut to length & bent to shape required including cranking, bending spirally for hoping for column, hooking ends & binding with and including mild steel wire not less than on 0.9mm dia or securing with clips complete all as specified and directed.

Taking down frames with shutters n exc 1.50 Square Metre each with shutter without taking off shutters from the frame complete all as specified and directed.

Taking down frames with shutters exc 1.50 Square Metre and n.exe 4 Square Metre each with shutter without taking off shutters from the frame complete all as specified and directed.

Taking down shutters exc 1 Square Metre and n exc 2 Square Metre each complete all as specified and directed.

S&F 4mm dia plain mild steel wire galvanised class3 in fencing including straining and fixing to concrete or steel post or to straining bolt including securing with and provision of galvanised iron staples or steel pin etc complete all as specified and directed.

S&F framed bracket of angle or Tee with web and flanges cut to shape drilled and countersunk including welding bending complete all as specified and directed.

S & F Mild steel 1.00 mm thick , plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

Material and labour for rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe-290-W (Gde E-165) quality 'A' complete all as specified and as directed by the Engineer-in-Charge.

M&L Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required exc half brick but not exc one brick complete all as specified and directed.

Supply and fixing of factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkhat of size 50 x 75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ Cubic Metre, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being teRunning Metreite/borer proof, water/ moisture proof and fire retardantand fixed in position with mild steel hold fast ( 35mmx35mmx3 MM ) of required length complete all as specified and directed. NOTE : - (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made. (ii) Material manufacture test certificate should be provided before execution of work

Supply and fixing of factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face supplying & fixing in frame at site complete all as per specification & drawing complete all as specified and directed.

Supply and fixing of factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkhat of size 100 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ Cubic Metre, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being teRunning Metreite/borer proof, water/ moisture proof and fire retardantand fixed in position with mild steel hold fast ( 35mmx35mmx3 MM ) of required length complete all as specified and directed. NOTE : - (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made. (ii) Material manufacture test certificate should be provided before execution of work

Supply and fixing of factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkhat of size 125 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ Cubic Metre, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being teRunning Metreite/borer proof, water/ moisture proof and fire retardantand fixed in position with mild steel hold fast ( 35mmx35mmx3 MM ) of required length complete all as specified and directed. NOTE : - (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made. (ii) Material manufacture test certificate should be provided before execution of work

Supply and fixing of factory made single extruded WPC (Wood Polymer Composite) solid decorative type moulded door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/Cubic Metre and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being teRunning Metreite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing all as per specification & drawing complete all as specified and directed

Supply and fixing of factory made single extruded WPC (Wood Polymer Composite) gauzed decorative type plain ( Jointless ) door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/Cubic Metre and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being teRunning Metreite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing all as per specification & drawing complete all as specified and directed. Note : wire mesh shall be paid seperately

Material and labour for providing and fixing of windows made of pre-painted steel(Base steel as per IS 513 of 0.58 mm thick "D" quality galvanized as per IS 277 witn zinc of 120 GSM). Primer caoted with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 nicrons thick alkyd backer. Section for outer frame should be 72x55mm, centre mullion should be of 72x55mm, section for shutter frame should be of 52x25mm and size of flymesh shutter should be of 20x40mm and rebate for glazed shutter and flymesh shutter with a 20mm provision for guard bars/grills. The sections are to be cut to lenght metre joined with corner bracket. Centre mullion is to be fixed with mullion cap. Shutter brackets with a inbuilt pvc lip to be fixed in a way that the lip overlaps the shutter corners and are not exposed. Handle, stay, 2 nos. of stainless steel heavy duty pivot hinges shall be provided per shutter the windows fitted with 4mm thick plain float/frosted glass with rubber gaskets including fixing the frames in concrete/masonry wall by MS holdfast, including fixed panel beading section should be of 12x12mm. Outer frame and mullions to have 10mm square guard bars with 6" (152.4mm) pitch etc., complete for finished item work.(Make: Elixir Met Form Pvt Ltd./ A2Z Infra Solutions/ Urban Space or equivalent) Note: Supply and fixing of glass panes and stainless steel wire mesh in glazed/gauged shutters of windows are inclusive in above rate, nothing extra shall be admissible in to this account.

Supply and fixing box type using ERW hollow 'P' section of size 60 x 25mm made from 1.25 mm thick MS sheet ventilators fixed type with glazing bar including MS grills of square bar 10mm dia @ 100 c/c complete with glazing bars dovetailed or welded, including two coat of synthetic enamel ordinary tint paint over a coat of red oxide primer complete all as specified and as directed by the Engineer-in-Charge.

S&F of ordinary glass 3mm thick with oil putty in square n exc 0.50 sq in each pane complete all as specified and directed.

S&F for bands hold fst etc including welding confiRunning Metre to fe 290 Gde E 165 complete all as specified by engr in charge

S&F 18mm thick lead free PVC celuka ply ( minimum density 600 Kg/ Cubic Metre) of both side plain of approved colour other than white colour fixed with stainless steel screws and solvent cement / adhesive to make kitchen / bed rooms cabinet sides, top and bottom and shelves inside the cabinets complete all as per manufacturer's specifications/ instructions complete all as specified and as directed by the Engr-in-charge.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps when open in 40mm complete all as specified and as directed by the Engineer-in-Charge

S & F 75mm extruded aluminium handles, cast type, fabricated type complete all as specified and as directed by the Engineer-in-Charge

S & F brass body ball catches with 8mm dia steel ball and striking plate including letting in complete all as specified and as directed by the Engineer-in- Charge

Taking down shutters exc 1 sq. M and n exc 2 sq. M each of any description including resecuring , easing ,adjusting and refixing in same opening complete all as specified and directed.

Supply and fixing for mild steel door shutter two leaves with frame of 20 gauges MS sheet ( all all round) and leaves of 21 gauge MS steel ( all as per Godrej pattern) with three way locking arrangement with brass lock & CP handles with duplicate keys including two coats of spray painting over a coat of red oxide primer complete in existing cup boards fixed with necessary nut bolts including embedding in PCC 1:2:4, complete, all as specified and as directed by the Engineer-in-Charge. Note : Area of opening shall be measured.

S&F as in repair Stainless steel wire cloth.0.36mm nominal dia of wireand average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 100 mm long butt hinges extruded aluminium alloy with galvanised mild steel hinge pine including screwing or welding to MS / PVC frame ( as required ) complete all as specified and directed.

S&F in Alumminium handles 125 mm,cast type ,anodised complete all as specified and directed.

Supply and fixing floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring of 140 mm cover plate size fixed in floor each complete all as specified and directed.

S&F as in repair mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate including welding or screwing to MS frame/PVC frame complete all as specified and directed.

S&F 200 mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed.

S&F 200mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed.

S&F 250MM long aluminium anodised sliding door bolt with hasp and staple(bolt type) and fixing clips of sheets cast of excruded section and fixing bolt and sliding complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal from site , complete all as specified and as directed by the engineer - in-charge

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal from site, complete all as specified and as directed by the engineer - in-charge

S&F GI pipe medium grade 15 mm dia with all fitting laid in floor or fixed in walls complete all as specified and directed.

S&F GI pipe medium grade 20 mm dia with all fitting laid in floor or fixed in walls complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F in repair Vitreous china orrisa pan squatting pattern 580 X 440mm with integeral foot rests including P or S trap PVC low level flushing cistern 10 ltrs capacity and Flush pipe of polyethylene of low or high density or PVC. 32 mm dia complete all as specified and directed. Note : The cost of traps , flushing cistern and PVC flush pipes are included in this item.

S&F in repair vitreous china wash hand basin star white size 400mm x 400 mm angle back including CI brackets, CP waste coupling,PVC waste pipe 32 mm bore complete all as specified and directed.

S&F as in repair sinks made of stainless steel ss grade 304 without drain board 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including providing and fixing cantilever CI brackets , PVC waste pipe , CP waste coupling and connecting union to pipe 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. Note : (i) The cost of waste coupling , PVC waste pipes are inclusive with this item and nothing extra will be admissible in to this account .

S&F as in repair fancy type pillar taps of 15 mm dia, cast copper alloy, with capstan heads, with chromium plated, screwed down high pressure with or without lettered 'hot' or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair 15 mm stop valves/Angle valve ,but fancy type, chromium plated , cast copper alloy,screwed down,high pressure, with flange cap , screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair 15 mm dia Bib taps fancy type , long shank , cast copper alloy with crutch or butterfly handle, screwed down, crewed with flange cap for iron pipe or for brass ferrule and fixed complete all as specified and directed.

M&L in repair Chromium plated shower rose 125 mm dia with shower arms with or without swivel joints including fixing to steel pipe or union complete all as specified and directed.

S&F in repair 15 mm concealed stop valves ,but fancy type, chromium plated , cast copper alloy,screwed down,high pressure, with flange cap , screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F as in repairs 15 mm dia 45 cm long PVC water connection with brass nuts ( Hot and cold ) and washers complete all as specified and directed.

S&F as in repair CP ( brass body ) Towel Rail 450mm long fixed with and including Chromium plates brass screws and wooden /plastic cleats (minimum weight 170gms ) complete all as specified and directed.

M&L for Stainless steel plate rack of size 24" x 30" x 10" of wall thickness not less than 0.60 mm and load capacity not less than 30 kg including fixing with stainless stell screws including taking down of old plate rack of any description complete all as specified and directed.

S&F in repair Stainless steel ( SS 202 grade ) Curtain rod 25 mm dia 0.80 mm wall thickness, mild steel, chromium plated including ornamental type supporitng and end brackets as per sample complete all specified and directed.

M&L for PVC (SWR) floor trap plain with CP grating including jointing with solvent cement outlet dia 75 mm in repair complete all as specified and directed. Note : Cost of grating are included in this item.

S& F In Repair CP Soap Dish of size 100mmx100mm of approved Design complete all as specified and directed.

Dismantling water tanks of capacity exc. 250 litre and not exc. 500 litres and removing from site and supply and fixing water storage tank, 500 litre capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm bore high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore, complete all as specified and directed.

Cutting into existing manhole for connecting into new drain, making good to pipe and rendering, cutting out existing benching for and conforming branch channel (1/2 round or ¾ section), in cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate, smooth finished and reforming benching as required for 75/110/100 mm bore PVC pipe, complete all as specified and directed.

Desilting of manhole complete by removing all scums, sludge, silt (both organic and inorganic nature) by manual labour or mechanical scraper and disposal of the same and buried in trenches etc, as in foul condition for any depth complete all as specified and directed. Note:- Sludge, scums, silt (both organic and inorganic nature) water shall be disposed off in closed container at authorized dumping site declared by local administration outside MD land.

Excavation in trenches not exc 1.50 mtr wide and n exc 1.50 mm in depth and getting out in soft/ loose soil for shafts, wells, cesspits, manholes, pier holes and NP2 pipes etc,. complete all as specified and directed.

Returning filling in including spreading, levelling, watering and wall ramming in layer n exc not exc 25 cm, any kind of soil complete all as specified and directed.

Removing execavated material n nexc 50m and depositing where directed at a level n exc 1.5m starting point complete all as specified and directed.

Demolition and beaking up drain AC pipes/PVC pipe set in cement mortar 100 mm and below complete all as specified and directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with PVC clamps or laid in trenches with PVC clam , bore of the pipe 110 mm complete all as specified and directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls bore of the pipe 75 mm complete all as specified and directed.

S&F PVC(SWR) bends 110 mm dia. With access door complete all as specified and directed.

S&F PVC(SWR) bends 75 mm dia.with access door complete all as specified and directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal with access door 110 mm bore complete all as specified and directed.

M & L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement including taking down old gully traps of any description complete all as specified and directed.

S & F PVC (SWR) vent cowl of 75 mm bore complete all as specified and directed.

S & F PVC (SWR) reducer of 75 x110 mm bore complete all as specified and directed.

Taking down cement plaster on brick or stone surfacs including raking out joints hacking for key scrubbing down with water etc. complete all as specified and directed.

Material and labour for repairing of RCC projection, chajjas, facia, bands, shelves, beams, RCC railing, balcony and similar works by dismantling of loose/ disintegrated portion of RCC at any height and in any sitution / floor (including provn of support, foRunning Metrework and welding of reinforcement if required with wire mesh of weight 3 kg/ Square Metre and dubbing/ filling with PCC (1:2:4), type B-0, using 12.5 mm graded aggregate,15 to 25 mm thick after applying cement slurry @ 3 kg/Square Metre, finished even and smooth to desired shape and applying two coats of cement based paint to match with existing surfaces complete all as specified and directed. Note:-Unit rate of this item includes the cost of scaffolding,foRunning Metrework etc. and nothing extra shall be paid on account of variation in height.

S&F Hard drawn steel wire fabric cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcent Weight per square metre N exc4 Kg complete all as specified and directed

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smoth without using extra cement with using water proofing compund @2% by weight of cement or as per manufacturer's instructions complete all as specidfied and directed.

M&L rough cast plaster complete as specified in SSR Part–I, clause 14.22 shall consisting of following :– firstly apply under coat in cement mortar 1:3 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine gravel aggregate which is generally of size between 6 to 12 mm depending on texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer–in–Charge.

Material and Labour for preparation to new plastered surfaces of wall including washing rubbing down and stopping of distempered or painted surfaces including all cornices, pilasters etc( plastered or unplastered) etc and applying two coat of acrylic exterior emulsion paint over and including one coat of alkali resistant primer with one coat 2-3 mm thick wall care cement based putty of approved colour/shade complete all as specified and directed by complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L for prepartion of new plastered/ concrete surfaces and applying two coats of distemper oil emulsion over and including one coat of primer and two coats of wall care putty complete all as specified and directed.

M & L for preparation of newly plastered surfaces of walls and applying two coats of white wash complete all as specified and directed.

M&L for rendering 5 mm thick on ceiling in CM 1:3 finished even and smooth without using extra cement complete all as specified and directed.

M&L preparation of new plastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed.

Complete removal of existing treatment on walls by with mechanical / electrical driven grinders suitable for removal work and scrapping washing rubbing down etc and applying two coats of water based distemper emulsion over and including two coats of acrylic based wall care putty with one coat of primer complete all as specified and directed.

Complete removal of existing treatment on ceiling by scrapping washing rubbing down etc and applying two coats of whitewash all as specified and directed.

M&L preparation of old decorated surfaces on walls ,chajjas , roof projection , cornices of brick /concrete surfaces etc. and applying two coats of acrylic exterior emulsion (white or tinted) complete all as specified and directed.

M & L for preparation of old decorated surfaces of walls and applying two coats of white wash complete all as specified and directed.

Preparation of old painted steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Painting on new steel surfaces and priming with red oxide primer of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L painting two coats of synthetic enamel paints on old wooden surfaces of girth exc 10CM , including preparation of surfaces complete all as specified and directed.

Taking down carefully aluminum point wiring (light, fan, socket or power) complete fittings such as switches, C/roses, Pendants DBs, sockets etc. including taking down carefully by unscrewing from boards/outlet/DBs/fittings such as switches, sockets, lamp holders, brackets, ceiling fittings bulkhead fittings, sketch fittings, tube light fittings, fan regulator, electric meters, meter box any type etc complete all as specified and directed. All the removed material to be deposited to AGE E/M store yard or will be handed over to the contractor under schedule of credit and making good to the disturbed surface by plastering and two coat of distamper complete all as specified and directed.

M & L for concealed point wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLS PVC insulated and unsheathed cable 1100 volts grade drawn through and including medium grade, ISI marked, PVC conduit,medium grade ISI marked not less than 20 mm dia with accessories fixed concealed/surface type on wall/ roof/ ceiling and including provision of 1.50 sqmm single core PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor green colour as earth conitnuity conductor and connected to common earth dolly with suitable size lugs, including mild steels sunken box or pressed steel terminal box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-1) of 1969 and IS:14772:2000 with earth dolly and coated with two coat of anti corrosive paint over a coat of red oxide primer both internally and externally with and including (provision of new) modular covered plate over sunken box for housing the modular switches, socket outlets., fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for :- Note:-1 Modular metal flush / sunken box, and for modular switch/ socket cover plate & sheet are inclusive in the item rate quoted. 2. Only switch, socket and fan regulators to be measured and paid seperately.

(a) One light/bell/fan/exhaust point controlled by one switch 6 amp one way complete all as specified and directed.

(b) One 3 pin switch socket combination 6 amp on the independent board complete all as specified and directed.

(c) One 3 pin switch socket combination on same board with other switches complete all as specified and directed.

M & L for concealed point wiring complete with 2.5 Sqmm single core multistranded copper conductor FRLS PVC insulated and unsheathed cable 1100 volts grade drawn through and including medium grade, ISI marked, PVC conduit,medium grade ISI marked not less than 20 mm dia with accessories fixed concealed/surface type on wall/ roof/ ceiling and including provision of 2.50 sqmm single core PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor green colour as earth conitnuity conductor and connected to common earth dolly with suitable size lugs, including mild steels sunken box or pressed steel terminal box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-1) of 1969 and IS:14772:2000 with earth dolly and coated with two coat of anti corrosive paint over a coat of red oxide primer both internally and externally with and including (provision of new) modular covered plate over sunken box for housing the modular switches, socket outlets., fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for:- Note:-1 Modular metal flush / sunken box, and for modular switch/ socket cover plate & sheet are inclusive in the item rate quoted. 2. Only switch, socket and fan regulators to be measured and paid seperately.

M&L switch modular type 6 Amp a way 1 module 230 volts complete all as sprecified and as directed.

M&L switch modular type 16 Amp a way 1 module 230 volts complete all as sprecified and as directed.

M&L socket modular 2/3 pin, 6 A one way 2 module 230 volts complete all as specified & as directed.

M&L socket modular 2/3 pin, 6/16 A one way 2 module 230 volts complete all as specified & as directed.

S&F Modular Bell Push 6 Amps one module complete all as specified and directed.

S&F electric bell AC, ding-dong type, 230 Volt, single pole complete all as specified and directed.

S&F ceiling rose 65x50mm three terminals 230 volt complete all as specified and directed.

S& F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting with 12W lED bulb complete all as specified and directed.

Supply & fixing of socket electronic type fan regulator modular 120 watt 2 module complete all as specified and directed.

Supply and fixing in replacement LED tube light fitting 1x18 watt, 230 volts in commercial channel with powder coated CRCA sheet housing with opal diffuser for LED with LED tubelight with high efficient LED in aluminium housing with clear & milky diffuser connecting with twin core twisted flexible copper conductor cable with suitable size rod complete with all accessories all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directred.

Supply and fixing in replacement LED bulk head 10 watt with pressure die cast aluminium housing high efficient LEDs including 10 watt LED bulb and enclosed with milky diffuser IP 66 protection complete all as specified and directed.

S&F LED Bldg Security Light Fittings of capacity 35 watt made up of die cast aluminium housing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including service bracket of GI pipe 32 mm bore medium grade of length 0.9 mtr with MS clamps, bolts, nuts, and washers and suitable reducer for connecting fitting to GI pipe as required at site and two coats of synthetic enamel paint over one coat of red oxide primer on mild steel work and making electrical connection, including disconnecting and taking down existing old U/S fitting complete all as specified and as directed.

M&L submain wiring with 2 runs of copper conductor FRLS PVC insulated unsheathed cable 1100 volt grade 6 sqmm drawn through PVC conduit medium grade ISI marked 25mm dia as per IS specification fixed concealed in wall/ceiling including conduit and conduit accessories and incl provn of PVC insulated 6.0 Sqmm FRLS multistranded copper conductor as earth continuity conductor connected to earth dolly all as specified including dismantling old and making good to the disturbed surface by plastering and two coat of distamper all as directed at site Note : Two runs of 6 sqmm cable alongwith one run of 6 Sqmm PVC insulated unsheathed copper conductor as earth wire, conduit and conduit accessories will be measured as one length complete all as specified and directed.

S&F in replacement MCBs 40 amp SPN B curve 240 Volts 10 KA finger proof terminal, bi-connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly, ISI marked to be fixed on DB complete all as specified and directed.

S&F in replacement MCBs 5 to 32 amp SP B curve 240 Volts 10 KA finger proof terminal, bi-connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly, ISI marked to be fixed on DB complete all as specified and directed.

S&F sheet metal MCB DBs 12 way with 200 Amps rated bus bar single pole and neutral with acrylic double door IP-43 fixed on wall duly grouted in solid block, including copper lugs/thimbles duly crimped for connection complete all as specified and directed.

Supplying and fixing of VTPN (including MCCB 100 Amp) distribution board 4 way fabricated out of thick high quality CRCA sheet. DBs shall be totally enclosed, suitable for 240V/415V, having polyurethane(PU) foam gasket to ensure IP-54 degree of protection for indoor application as per IEC 61439-3:2012(Cl. 10.3)/IEC 60529.DB shall be robust with tested for Impact resistance IK09 as per IEC 61439-3:2012(Cl.No. 10.2.6).DBs shall be provided with prefitted cement Guard. DB Door shall have detachable gland plates provided with proper knockout holes of 26mm/35mm diameter for intsertion of cable/conduits.Distribution Boards shall be provided with wire set of copper along with the insulated fork type bus bars.DB shall have reversible hinged doors and possibility to allow door opening from Left to Right or Right to Left for convenience on site.DB shall have type test reports as per IEC 61439-3 from ERDA or NABL laboratory complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4.0 core complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundations, manholes, etc. or for laying cables/pipes, erecting poles, etc. not exceeding 10sqm on plan and getting out in any type of soil complete all as specified and directed.

Returning, filling in, including, spreading, leveling, watering and well ramming in layers not exceeding 25cm deep as in any type of soil complete all as specified and directed.

Removing execavated materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point in any type of soil including spreading in low lying area and leveling complete all as specified and directed.

Supply and laying well burnt brick class-B laid flat to cover the cable with width equal to the length of cable and abutting each other for protection of cable complete all as specified and directed.

M&L dry sand cushoning to cable i.e 8 cm before laying cable in trenches and 15 cm after laying the cable and compacting complete all as specified and directed. Note: punned thickness shall be measured for payment.

S&F light grade GI Tubing of size 40mm dia for cable protection and fixed with clamp to pole and wall with nut, bolts, washers or in trenches as in repair complete all as specified and directed.

Material and labour Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed.

Note:- Amount of credit of Rs. 1,16,390.00 for retrieved materials is mentioned in Schedule of Credit Page No. 17 & 18 of tender documents in pdf form which will be deducted offline while acceptance of tender.

M/s B.S.Jain (BID ID -3394839)

Durga Enterprises (BID ID -3398111)

Sham Sunder Bansal (BID ID -3397897)

Swami Enterprises (BID ID -3403574)