Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL).

Karnataka Power Transmission Corporation Limited

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

TECHNO - COMMERCIAL SHEETS

NOTE* For detailed scope of the work please refer Bid Documents.

BIDDERS TO READ CAREFULLY

THE FOLLOWING DOCUMENTS [DULY SIGNED BY AUTHORISED PERSON, WHEREVER NECESSARY] ARE TO BE UPLOADED AND BANK GUARANTEE TOWARDS EMD OVER AND ABOVE RS.10.00LAKH AS PER ANNEXURE-II OF THE BID DOCUMENT SHALL BE SENT IN ORIGINAL TO CHIEF GENERAL MANAGER, KPTCL, BENGALURU SO AS TO REACH THIS OFFICE AFTER THE LAST DATE OF SUBMISSION OF BID AND ON OR BEFORE THE DATE & TIME NOTIFIED FOR OPENING OF TECHNO COMMERCIAL BIDS, FAILING WHICH THE BID WILL NOT BE OPENED. 1) NO DEVIATION CERTIFICATE (SCHEDULE-16). 2) EMD/BID SECURITY AS DETAILED IN CLAUSE NO. 13 of ITT. 3) BANK GUARANTEE TOWARDS BALANCE EMD/BID SECURITY issued either by a Nationalized/Scheduled Bank. (For the balance EMD above Rs. 10Lakhs (SCHEDULE-17) - as detailed in Clause No. 13 of ITT-The Bidder shall scan the Bank Guarantee towards EMD and upload the same in the prescribed format in the slot specified for “EMD and Tender Fee Payments” in the e-procurement portal to enable the owner for verification of EMD BG at the time of opening of Techno Commercial Bid, failing which the offer will be rejected. 4) LETTER OF UNDERTAKING (SCHEDULE-18). 5) CONSORTIUM AGREEMENT (IF APPLICABLE-SCHEDULE-19) 6) POWER OF ATTORNEY (SCHEDULE- 20). 7) ANY OTHER AGREEMENTS /UNDERTAKINGS/SELF DECLARATIONS SPECIFIED IN THE TENDER.

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

BID PROPOSAL SHEET

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

Bidder's Name & Address alongwith GSTIN no. :

Bid Proposal Reference :

Person to be contacted :

E-Mail Address:

The Chief Engineer Electy.,

Transmission (Operations) Zone

KPTCL, Kalaburagi-585105

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

a) * We have submitted bid as individual Bidder. (Indicate Name of the Individual Bidder)

b) * We have submitted bid in Consortium with the following Bidders. (Key in Consortium) VOID

Name of the Consortium Partner Scope / Participation of each Consortium Partner

(* Fill-up whichever is applicable)

1 We, the undersigned Bidder, having read and examined in detail the specifications and all the Bidding documents of the said work and hereby propose to design, manufacture/fabricate, shop test, supply on FOR site basis, and carry out the erection, testing and commissioning including civil, structural and architectural works for

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

2 PRICES AND VALIDITY :

2.1 We declare that the Prices stated in our Proposal are in accordance with subject Bid Documents (including Clause No.40 of "Conditions of Contract (CC)" & Clause No.12 of Instruction to Tenderers (ITT) of Bid Documents. We further declare that all Ex-works price/CIF components of Spares, Maintenance and Testing Equipments and other charges viz., Freight and Insurance, Type Test charges and other charges stated in our proposal shall be as per the Tender conditions. All the Price and other terms and conditions of this Proposal are valid during the Performance of the Contract.

2.2 All Duties, such as Custom Duties on imports, Levies, Surcharge/Cess etc., if any applicable on the transaction excluding GST are included in the Bid Price and shall be to Our account and the Owner is not having any liability whatsoever on this account, whatever may be the contrary elsewhere in the Bid documents. However the component of Duties included in the Bid Price are separately indicated in Schedule - 2 for TDS purpose. We further confirm that our Bid Prices as quoted in Schedule-I, include all import Duties and levies including Licence fees lawfully payable by us on imported items and all other Duties and Levies applicable on Bought-out Components, Materials, Equipment and other items and confirm that any such Duties and Levies additionally payable shall be to our account. We further confirm that, no Sales Tax in any form shall be payable by Owner either for Bought-out items which are despatched by our Sub-Suppliers directly to the Project Site or for items Supplied directly by us. We confirm that, the Prices quoted by us are excluding GST.

2.3 We declare that we have noted and considered Clause No.39 of Conditions of Contract (CC ), Clause No. 11.11 of Instruction to Tenderers(ITT) of Bid Documents regarding Taxes and Duties and quoted our Prices accordingly. We further agree for TDS as per Statutory stipulations.

2.4 The Bid Prices, the Price components of the various items in our Scope of Supply, Erection including Testing & Commisisoning, Civil and Mandatory spares is quoted in Itemwise Financial Bid in e-Procurement Portal for this proposal..

3 CONSTRUCTION OF THE CONTRACT : We, declare that we are making the Offer on the basis of Single Contract for the entire Scope of the Package in accordance with Clause No.26.2 of Instruction to Tenderers (ITT) of Bid Document.

4 We having studied Clause No.39 of Conditions of Contract (CC ), Clause No. 11.11 of Instruction to Tenderers(ITT) of Bid Documents , relating to Tax and we hereby, declare that if any income-tax, surcharge on income tax or any other corporate tax is attracted under the law, we agree to pay the same.

5 Bid Security/ EMD : Bids are accompanied by Bid Security (EMD) for Rs.15.78Lakhs.We have enclosed a Bid Security through e-Payment mode for a sum of Rs.10.00Lakhs and remaining amount of Rs.5.78Lakhs ( above Rs.10 Lakhs) in the form of Bank Guarantee in original and two copies of the original valid for a period of 225 days from the Last date of bid submission as notified (either original or extended), and liable to be forfeited in accordance with Bid Documents. (Mode of Payment towards EMD is as detailed in CLAUSE NO. 13 of ITT & Clause No. 5 of NIT)

We have also ensured that the above Bid Guarantee furnished by us is in line with the Bid Documents and complete in respect of following :

1. Value of Non judicial Stamp Paper purchased in the name of executing Bank is as per Stamp Act.

2. Power of Attorney Number and Date as well as Signature and Full Name and Designation of Executant along with Bank's Stamp are there.

3. Signature, Full Name, Designation and address of Witness are there.

4. Completed Mailing address of the Head Office of the Bank is indicated.

6.1 We declare that the Works shall be performed strictly in accordance with the Specifications and Documents except for the variations and Deviations, all of which have been detailed out exhaustively in the following Schedules, irrespective of whatever has been stated to the contrary anywhere else in our Proposal.

a Commercial Deviations Schedule Schedule - 5

b Technical Deviations Schedule Schedule - 6

6.2 We further confirm that Specified Stipulation of following Clauses are acceptable to us and No Deviation / Exceptions are taken on any account whatsoever in the following Clauses.

a. Terms of payment Clause No. 37 of Section-5,Conditions of Contract (CC) and Clause No.8 of Special Conditions of Contrac (SCC)

b. EMD/Bid Security Clause No. 6, Section :1, Invitation for Tenders (IFT) and Clause No. 13, Section :2, Instruction to Tenderer (ITT)

c. Contract Performance Guarantee Clause No. 29 of Section:2, Instruction to Tenderers (ITT).

d. Penalty for delay Clause No. 41 of Section-5 : Conditions of Contract (CC).

e. Price Basis/ Price adjustment Clause No. 40 of Section-5 :Conditions of Contract (CC).

f. Defects Liability Period/Guarantee Clause No. 10 of Section-5 Special Conditions of Contract (SCC)

g. Work Schedule Clause No.17 of Section:5 Conditions of Contract (CC)

h. Taxes and Duties Clause No. 11.11 of Section-2: Instruction to Tenderers (ITT).

Further, we agree that additional conditions, if any, found in the Proposal Documents other than those stated in Deviation Schedules, save that pertaining to any rebates offered, shall not be given effect to.

7 PERFORMANCE GUARANTEE ; We declare that the ratings and performance figures of the equipment to be supplied and erected by us are guaranteed. The Guaranteed particulas of different equiment in our Scope are enclosed in Data Requirement Sheets.

8 BID PRICING : We further, declare that the Prices stated in our Proposal are in accordance with your ITT & SCC & all other relevant clauses of Bid Documents.

9 PRICE ADJUSTMENT : We declare that the Prices quoted by us are in accordance Clause No. 40 of Section-5 :Conditions of Contract (CC)

10 SPECIAL TOOLS AND TACKLES : We have given a list of Special Tools and Tackles in Schedule - 7 and Prices thereof are included in our lumpsum Bid Price. We further agree that any items of Special Tools and Tackles, though not included in the aforesaid list, but required for effective Erection, Testing, Commissioning & Operation of the Equipments of Substations & Transmission lines shall also be furnished by us, at no extra cost to you.

11 ADDITIONAL INFORMATION : In addition to the information called for in these Proposal Sheets, we have included with this Proposal, additional information as listed in Schedule - 8. We further confirm that such additional information does not imply any additional deviation beyond those covered in Schedule - 5 & 6 and in case of any contraction between these additional information and other provisions of Bid, the later will prevail.

12 QUALIFICATION DATA : We confirm having submitted the Qualification Data, as required by you in your Bid Documents in e-Procurement Portal along with this Proposal. Further we have filled in the information for Qualification Requirements in Schedule 9. In case you require any further information in this regard, We agree to furnish the same in time.

13 WORK SCHEDULE : If this Proposal is accepted by you, we agree to submit Engineering Data, Provide Services and complete the entire Work from time to time, in accordance with Schedules indicated in the Proposal. We fully understand that the Time Schedule stipulated in this Proposal is the essence of the Contract, if awarded. The completion schedule of the various Major Key Phases of the Work is indicated in Schedule - 11.

14 CONTRACT PERFORMANCE GUARANTEE ; We further agree that if our Proposal is accepted, we shall provide an irrecoverable Contract Performance Guarantee, of value equivalent to Five percent (5%) of the Amount Put to Tender (Excluding GST) plus additional security for unbalanced tenders in accordance with Clause 29 of Instructions To Tenderers (ITT) of the tender valid up to the end of ninety (90) days after the end of the Contract Guarantee Period mandatorily in the form of electronic Bank Guarantee (e-BG) from the Banks which are integrated with NeSL in the form attached as Annexure-III (Section 4: Formats of Annexures) in your favour in accordance with Clause 25.5 of ITT and Clause 43 of the CC (Conditions of Contract), as per the format given in Section 4 and enter into a formal agreement with you within Twenty (20) days from the date of issue of Letter of Intent to Award the Contract.

16 BID PRICE : We declare that our lumpsum Price for the entire scope of work specified in the specifications and documents, shall be as indicated in Schedule - 1.

17 CHECK LIST : We have included a Checklist duly filled in Schedule 22

18 We, hereby, declare that only the Persons or Firms interested in this Proposal are named herein as Principals and that no other Persons are interested in the Proposal or in the Contract to be entered into, if we are awarded the Contract, and that this proposal is made without any connection with any other Person, Firm or Party likewise submitting a Proposal and that this Proposal is in all respect for and in good faith, without collusion or fraud.

19 We declare, in case our bid is accepted, that until a formal Contract is prepared & executed, this bid together with your written letter of acceptance thereof and your notification of award /Letter of Intent to Award the Contract shall constitute a binding contract between us. We further understand that you are not bound to accept the lowest or any bid you may receive.

Thanking you, we remain,

Yours faithfully,

Place Printed Name

Business Address Country of Incorporation (State or Province to be indicated)

Name and Address Principal Officer

Karnataka Power Transmission Corporation Limited

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

KPTCL/2026-27/SS/ Vadavatti Enhancement.

FILL ONLY IN LIGHT BLUE COLOURED CELLS.

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

We declare that in terms of Clause No. 11 of ITT, Bid documents, the following are our lumpsum price in Rupees for the entire scope of work as specified in the Specifications and Documents.( Inclusive of all Taxes (Excluding GST) & Duties).

Total Lumpsum Price : ( In Figures) Note: Fill as "YES" against this column in case Prices are indicated in the Item-Wise Bid Financial Offer in figures

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 2 (1 of 2)-SUMMARY OF PRICE COMPONENTS

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

KPTCL/2026-27/SS/ Vadavatti Enhancement.

FILL ONLY IN LIGHT BLUE COLOURED CELLS.

Summary of Price Components

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

Summary price components for identified in accompanying specifications

( Name of the Work) as per the scope identified in accompanying specifications.

Sl no Description Amount in Rs. (Fill as "YES" against the above Price columns in case Prices are indicated in the Price templates)

A Material / Equipment Price (including Packing & Forwarding charges) in the Scope of the Contractor

i) Ex-works including all taxes & duties [As per schedules -

ii) Freight and Insurance Charges (Not Applicable) [As per schedules - 3A(i) for Station & 3B(i) for Line]

iii) Total FOR site price (i+ii)

B Mandatory spares price (including packing & forwarding charges)

i) Ex-works including all taxes & duties

ii) Freight and Insurance Charges(Not Applicable) (As per schedule -4)

iii)Total FOR site price (i + ii)

C Supply portion total FORD price [A+B]

D Erection portion:

i) Total charges for Erection, Testing & Commissioning of all Supply items [as per schedules-

ii) Total charges for entire civil works [ as per Schedules-

iii) Total civil works, erection, Testing and commisioning charges (i)+(ii)

E Total Bid Price = C+D(iii) In figures : Rs.

Total Bid Price in Figures : Rs.

Total Bid Price in words : Rupees

Note: The erection charges shall include the charges for taking delivery at Owner's store, unloading, handling, storage, erection, testing and commissioning of all equipments .

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 2 ( 2 of 2 ) - TAXES(Excluding GST), DUTIES & OTHER LEVIES

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Fill IN LIGHT BLUE COLOURED CELLS.

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

Estimates of Indian Taxes (Excluding GST), Duties and Levies included in the Total Bid Price are as follows:

SL. No. Description of Applicable Tax (Excluding GST) / Duty / Levy 00

Rate of Tax (Excluding GST)/ Duty / Levy Amount of Taxes (Excluding GST) / Duties in Rupees Rate of Tax (Excluding GST) / Duty / Levy Amount of Taxes (Excluding GST)/ Duties in Rupees

1 SGST/UTGST Applicable taxes (Excluding GST), duties & levies prevailing as on the last date of bid submission shall be quoted

i. Supply Portion

ii. Erection Portion

iii. Civil Portion

i. Supply Portion

ii. Erection Portion

iii. Civil Portion

i. Supply Portion

ii. Erection Portion

iii. Civil Portion

6 Building and other construction workers welfare Cess for Supply, Erection and Civil Portion works

8 a. Applicable Customs Duty (*) (Bidders shall also clearly indicate the breakup of Customs duty such as BCD, Cess,etc.,)

b. If there is any existing Treaty between India and the country from where the goods required for this project are proposed to be imported, then copy of the treaty shall be uploaded.

9 Other Taxes & duties if any (Specify) **

10 Other Taxes & duties if any (Specify) **

11 Total (Sum of 1 to 10)

(*) In case of CIF portion of Supply.

** Please Specify the nature of the other Taxes (Excluding GST) along with the details in the "Rate" Column.

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 2A : SCHEDULE OF DISCOUNT

SHEET FOR TECHNOCOMMERCIAL OPENING (UN - PRICED)

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

KPTCL/2026-27/SS/ Vadavatti Enhancement.

FILL ONLY IN LIGHT BLUE COLOURED CELLS.

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

We hereby offer an unconditional discount on our quoted price in Schedule 2 (1 of2) as under. Any discounts offered anywere else in Bid shall not be considered.

Sl.No Nature of Discount 00

Percentage of discount Amount (in Rs.) (Fill in as 'YES' in case Prices are indicated in the Item-Wise Bid Financial Offer) Remarks

I Supply Schedules a) Ex-works prices

b) Freight & Insurance (Not Applicable)

II Erection Schedules

III Civil Works Schedules

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE- 2 B - STATEMENT OF COMMERCIAL TERMS AND CONDITIONS

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

Details of payments made in the form of Credit card/Debit card/NEFT/RTGS/OTC (over the counter) as per the tender conditions should be keyed in against column no. 3 (a) . BG Amount, BG No. and date, Name and address of the bank issuing the BG, validity of the BG should be keyed in against column no. 3 (b) .

FILL ONLY IN LIGHT BLUE COLOURED CELLS.

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

STATEMENT OF COMMERCIAL TERMS AND CONDITIONS

Sl. No. Particulars Details

1 Bid proposal form Uploaded.

2 No deviation certificate Uploaded.

3. a). EMD / Bid Security Bids shall be accompanied by bid security (EMD); 1) Rs.50000/- The following modes of payment will be provided as a part of e-Payment services. • Credit Card/Debit Card • Net Banking • NEFT/RTGS • Over-the-Counter (OTC) • IMPS For further detail regarding mode of e-payment of EMD in e-procurement platform, contact e-procurement cell, Government of Karnataka.

b). EMD amount above Rs.10Lakh by Bank Guarantee

4 Validity of the Bid.

5 Qualifying Requirements.

6 Financial capability

8 Taxes & Duties.

9 Completion Schedule

10 Defects Liability Period/Guarantee

11 Payment Terms

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3A(i) - Price Breakup for - Supply portion

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

Bidder's Name & Address alongwith GSTIN no. :

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

BIDDERS SHALL FILL ONLY IN THE LIGHT BLUE COLOURED CELLS.

SUPPLY PORTION: Unit Quantity Indicate whether "Own manufactured Iem" or "Bought Out Item" Indicate country of Origin

Sl No. Name of the Equipment/Materials

A1 11kV Isolators

1 11 kV isolators, double break 800 A 25 KA capacity with rigid bi-metallic terminal connector suitable for Drake ACSR for incomer Set 2

2 11 kV isolators, double break 400 A 25 KA capacity with rigid bi-metallic terminal connector suitable for coyote ACSR for feeders/Capacitor Bank Set 5

3 11 kV isolator, single break 400 A, 25 KA capacity with roaster switch and rigid bi-metallic terminal connectors suitable for coyote ACSR. Set 4

A2 Current Transformer

1 11kv class outdoor Current Transformer of ratio 1200-600/1-1-1A with 0.2 accuracy class. Note: The make and characteristics of 11kv NCT should be the same as that of the incomer CT of 11kv bank switchgear. No 3

2 11kv class,25kA,NCT of ratio 1200-600/1-1-1A for REFR protection(of similar rating and ratio as that of incomer of 11kv switchgear)with terminal connectors suitable for 100*6mm copper flats No 1

A3 Lightning Arrestor :( Polymeric )

i. 9 KV, 10KA Station Class with connector and clamps Nos. 12

A4 Control Panels : Simplex Type Control and Relay Panel complete as per specifications (Control Voltage 110 V DC).

1 For Power Transformer 20 MVA, 110/11KV Nos. 1

A5 Sation structures

1 11 kV ODS structure Column out of 9.5 MTR., long RCC pole for 300 kGs working load (Using TOR 50 steel 10mm) for 11 kV ODS . Nos 10

2 Beams out of Galvanised iron channel of size 100 x 50 mm with arrangement for stringing power conductor on 11 kV side 1B1 7.45 Mtr long with clamps, bolts and nuts (No 1) [0.071 MT for each Nos] Nos. 12/0.8568

3 Beams out of Galvanised iron channel of size 100 x 50 mm with arrangement for stringing power conductor on 11 kV side 1B2 4.0 Mtr long with clamps, bolts and nuts (No 1) [0.038 MT for each Nos] Nos. 16/0.6048

4 Supplying of D.P. Structure with all accessories using 9.0mtrs long, 145Kg WL RCC poles including H frame suitable for mounting roaster GOS / DB GOS with provision for fixing 9KV lightning arrestors etc., complete. Sets 4

A6 GI Mounting structure including Bolts & Nuts (Lattice type) (For 110KV Sub-Station) - (Approx. Unit Wt. in MT add 5% towards B & N)

1 11kV UG cable terminating structure for LV side of transformer (0.072 MT per structure) Nos/MT 1/0.072

A7 BUS BAR FORMATION:

1 Drake ACSR Mtrs. 100

2 Coyote ACSR Mtrs. 400

3 Formation of main/ cross BUS with single Drake Conductor for 11kV Bay 4

4 Formation of main/ cross BUS with single Coyote Conductor for 11kV Bay 5

A8 Insulators :

1 Single Tension string of 90 KN. 2 units each along with hardware suitable for Drake ACSR.(11 kV) String 33

2 Single Tension string of 90 KN,1units each along with hardware suitable for Coyote ACSR(11 kV) String 36

3 Single Suspension string of 90 KN, 2 units each along with hardware suitable for drake ACSR(11kV) String 9

1 C - Clamp suitable for Drake - Drake - Fired Wedge Connector Type Nos 12

2 C type Wedged Clamp suitable for Drake-Coyote Nos 21

3 C type Wedged connector suitable for Coyote-Coyote Nos 54

A10 Copper Control Cables : 1.1kV PVC insulated Copper Control Cable with Lugs/Ferrules as per technical specifications.

1 19 C x 2.5 Sqmm Mtrs 600

2 4 C x 6.0 Sqmm Mtrs 500

3 4 C x 4 Sqmm Mtrs 300

4 2 C x 2.5 Sqmm Mtrs 350

A11 11KV Switchgear : 11kV, 350MVA, 20KA, PCVCB Switchgear (1250A for Incomer and 800 A for feeders), outdoor type, each comprising of 1I/C+4F+1CB+1AP (Remote Announciation cum Control panel) with CTs & PTs complete as per technical specification. Set 1

A12 AC distribution Box Single front (outdoor type) 6 Terminal 1200 x 1350 x 300 mm, one I/C of 100AMCCB 20kA + 6 O/G MCB 16 A + 1 O/G of 100A, HRC fuse panel 415V Nos 1

A13 DC distribution panel (indoor) as per technical specification comprising of earth fault indicator, indication circuit for AC mains failure, 1 no. 100A SFU for I/C + 12 nos. 32A SFU for O/G Nos 1

A14 HV Cables & termination Kit for XLPE cable

1 11 KV class 1x1000 sq.mm UG cable XLPE 3 runs of 1C x 1000Sqmm Cable to connect bank Mtrs 250

2 Heat shrinkable type cable termination kits suitable for 1x1000 Sqmm XLPE cable (Outdoor type) Nos. 8

A15 Capacitor Bank :2.9 MVAR, 12.1 KV Capacitor Bank, Design, Engineering , supply, erection, testing & commissioning of 2.9MVAR, 12.1KV Capacitor Bank,star connected, double bank with internal fuses, terminal connectors, with suitable neutral CTs, and station class LA's, 0.2% series reactor, on neutral side with mounting structures for NCT, Capacitor Bank, Station class LA's, series reactor etc., complete as per specification. Sets 1

A16 Equipments for establishing SCADA Communications:

1a. Current Cables-Copper Core with c/s 4.0 sq.mm Multistrand 7 core Mtr 20

b Voltage Cables-Copper Core with c/s 2.5 sq.mm Multistrand 4 core Mtr 20

c Single Cables-armoured Copper Core with c/s 0.5 sq.mm Multistrand 10 core Mtr 20

d Control Cables-Copper Core with c/s 1.5 sq.mm Multistrand 10 core Mtr 20

2 One number with 8input and output points for 110V DC to 48V DC Opto coupler mounted within the RTU panel for indication ( as per market value) Each 1

3 MFT 3 phase 4wire 110V DC 1A, 50Hz, self powered with RS 485 compitable to MOODBUS protocal for 11kV Switch gear panel 1I+4F+1AP ( as per Market rate) Each 6

4 RJ -45 cable for Energy meter integration to DCU ( market rate) Mtr 5

5 Terminal blocks (knife type) Each 12

6 Contact Multier Relay (CMR)-48V DC3 NO+NC Contact Each 12

7 Integration of RTU, DCU and UPS with field equipments Nos 1

A17 Earth mat Formation:-

1 Grounding of equipments with 50X6 mm GI Flat and connecting equipment to the earth mat/Ground pit including all connected works with all materials supplied by the contractor. Rmtrs 400.00

2 Grounding of equipments by providing cast iron pipe of 100mm ID 13mm thickness, 2.75mtrs long with 2 part clamp out of G.I.Flat 50x6 mm continuously welded around the pipe using cast iron welding electrodes as per drawing including the cost of excavation, providing & laying homogeneous mixture of charcoal lumps, salt & sand all round the pipe as per specification. No. 8.00

3 Supplying and fixing of RCC collar of size 450mm dia, 450mm height 1.5" to 2" Hume pipe collors for earth pits No. 8.00

4 Supplying & fixing of Earthing Name Plate. L/s 1.00

Place Designation

Name of Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3A(ii) - Price Breakup for - ERECTION PORTION INCLUDING TESTING & COMMISSIONING and DISMANTLING PORTION.

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

Bidder's Name & Address alongwith GSTIN no. :

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

BIDDERS SHALL FILL ONLY IN THE LIGHT BLUE COLOURED CELLS.

ERECTION PORTION INCLUDING TESTING & COMMISSIONING and DISMANTLING PORTION:

ERECTION PORTION INCLUDING TESTING & COMMISSIONING and DISMANTLING PORTION: Quantity Indicate whether "Own manufactured Iem" or "Bought Out Item" Indicate country of Origin

Sl No. Name of the Equipment/Materials Unit

A1 11kV Isolators

1 11 kV isolators, double break 800 A 25 KA capacity with rigid bi-metallic terminal connector suitable for Drake ACSR for incomer Set 2

2 11 kV isolators, double break 400 A 25 KA capacity with rigid bi-metallic terminal connector suitable for coyote ACSR for feeders/Capacitor Bank Set 5

3 11 kV isolator, single break 400 A, 25 KA capacity with roaster switch and rigid bi-metallic terminal connectors suitable for coyote ACSR. Set 4

A2 Current Transformer

1 11kv class outdoor Current Transformer of ratio 1200-600/1-1-1A with 0.2 accuracy class. Note: The make and characteristics of 11kv NCT should be the same as that of the incomer CT of 11kv bank switchgear. No 3

2 11kv class,25kA,NCT of ratio 1200-600/1-1-1A for REFR protection(of similar rating and ratio as that of incomer of 11kv switchgear)with terminal connectors suitable for 100*6mm copper flats No 1

A3 Lightning Arrestor :( Polymeric )

i. 9 KV, 10KA Station Class with connector and clamps Nos. 12

A4 Control Panels : Simplex Type Control and Relay Panel complete as per specifications (Control Voltage 110 V DC).

1 For Power Transformer 20 MVA, 110/11KV Nos. 1

A5 Sation structures

1 11 kV ODS structure Column out of 9.5 MTR., long RCC pole for 300 kGs working load (Using TOR 50 steel 10mm) for 11 kV ODS . Nos 10

2 Beams out of Galvanised iron channel of size 100 x 50 mm with arrangement for stringing power conductor on 11 kV side 1B1 7.45 Mtr long with clamps, bolts and nuts (No 1) [0.071 MT for each Nos] Nos. 12/0.8568

3 Beams out of Galvanised iron channel of size 100 x 50 mm with arrangement for stringing power conductor on 11 kV side 1B2 4.0 Mtr long with clamps, bolts and nuts (No 1) [0.038 MT for each Nos] Nos. 16/0.6048

4 Supplying of D.P. Structure with all accessories using 9.0mtrs long, 145Kg WL RCC poles including H frame suitable for mounting roaster GOS / DB GOS with provision for fixing 9KV lightning arrestors etc., complete. Sets 4

A6 GI Mounting structure including Bolts & Nuts (Lattice type) (For 110KV Sub-Station) - (Approx. Unit Wt. in MT add 5% towards B & N)

1 11kV UG cable terminating structure for LV side of transformer (0.072 MT per structure) Nos/MT 1/0.072

A7 BUS BAR FORMATION:

1 Drake ACSR Mtrs. 100

2 Coyote ACSR Mtrs. 400

3 Formation of main/ cross BUS with single Drake Conductor for 11kV Bay 4

4 Formation of main/ cross BUS with single Coyote Conductor for 11kV Bay 5

A8 Insulators :

1 Single Tension string of 90 KN. 2 units each along with hardware suitable for Drake ACSR.(11 kV) String 33

2 Single Tension string of 90 KN,1units each along with hardware suitable for Coyote ACSR(11 kV) String 36

3 Single Suspension string of 90 KN, 2 units each along with hardware suitable for drake ACSR(11kV) String 9

1 C - Clamp suitable for Drake - Drake - Fired Wedge Connector Type Nos 12

2 C type Wedged Clamp suitable for Drake-Coyote Nos 21

3 C type Wedged connector suitable for Coyote-Coyote Nos 54

A10 Copper Control Cables : 1.1kV PVC insulated Copper Control Cable with Lugs/Ferrules as per technical specifications.

1 19 C x 2.5 Sqmm Mtrs 600

2 4 C x 6.0 Sqmm Mtrs 500

3 4 C x 4 Sqmm Mtrs 300

4 2 C x 2.5 Sqmm Mtrs 350

A11 11KV Switchgear : 11kV, 350MVA, 20KA, PCVCB Switchgear (1250A for Incomer and 800 A for feeders), outdoor type, each comprising of 1I/C+4F+1CB+1AP (Remote Announciation cum Control panel) with CTs & PTs complete as per technical specification. Set 1

A12 AC distribution Box Single front (outdoor type) 6 Terminal 1200 x 1350 x 300 mm, one I/C of 100AMCCB 20kA + 6 O/G MCB 16 A + 1 O/G of 100A, HRC fuse panel 415V Nos 1

A13 DC distribution panel (indoor) as per technical specification comprising of earth fault indicator, indication circuit for AC mains failure, 1 no. 100A SFU for I/C + 12 nos. 32A SFU for O/G Nos 1

A14 HV Cables & termination Kit for XLPE cable

1 11 KV class 1x1000 sq.mm UG cable XLPE 3 runs of 1C x 1000Sqmm Cable to connect bank Mtrs 250

2 Heat shrinkable type cable termination kits suitable for 1x1000 Sqmm XLPE cable (Outdoor type) Nos. 8

A15 Capacitor Bank :2.9 MVAR, 12.1 KV Capacitor Bank, Design, Engineering , supply, erection, testing & commissioning of 2.9MVAR, 12.1KV Capacitor Bank,star connected, double bank with internal fuses, terminal connectors, with suitable neutral CTs, and station class LA's, 0.2% series reactor, on neutral side with mounting structures for NCT, Capacitor Bank, Station class LA's, series reactor etc., complete as per specification. Sets 1

A16 Equipments for establishing SCADA Communications:

1a. Current Cables-Copper Core with c/s 4.0 sq.mm Multistrand 7 core Mtr 20

b Voltage Cables-Copper Core with c/s 2.5 sq.mm Multistrand 4 core Mtr 20

c Single Cables-armoured Copper Core with c/s 0.5 sq.mm Multistrand 10 core Mtr 20

d Control Cables-Copper Core with c/s 1.5 sq.mm Multistrand 10 core Mtr 20

2 One number with 8input and output points for 110V DC to 48V DC Opto coupler mounted within the RTU panel for indication ( as per market value) Each 1

3 MFT 3 phase 4wire 110V DC 1A, 50Hz, self powered with RS 485 compitable to MOODBUS protocal for 11kV Switch gear panel 1I+4F+1AP ( as per Market rate) Each 6

4 RJ -45 cable for Energy meter integration to DCU ( market rate) Mtr 5

5 Terminal blocks (knife type) Each 12

6 Contact Multier Relay (CMR)-48V DC3 NO+NC Contact Each 12

7 Integration of RTU, DCU and UPS with field equipments Nos 1

A17 Earth mat Formation:-

1 Grounding of equipments with 50X6 mm GI Flat and connecting equipment to the earth mat/Ground pit including all connected works with all materials supplied by the contractor. Rmtrs 400.00

2 Grounding of equipments by providing cast iron pipe of 100mm ID 13mm thickness, 2.75mtrs long with 2 part clamp out of G.I.Flat 50x6 mm continuously welded around the pipe using cast iron welding electrodes as per drawing including the cost of excavation, providing & laying homogeneous mixture of charcoal lumps, salt & sand all round the pipe as per specification. No. 8.00

3 Supplying and fixing of RCC collar of size 450mm dia, 450mm height 1.5" to 2" Hume pipe collors for earth pits No. 8.00

4 Supplying & fixing of Earthing Name Plate. L/s 1.00

Place Designation

Name of Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3C(i) - Price Breakup for - Station Civil Portion.

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

Bidder's Name & Address alongwith GSTIN no. :

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

BIDDERS SHALL FILL ONLY IN THE LIGHT BLUE COLOURED CELLS.

CIVIL WORKS PORTION

Sl. No. Particulars Unit Qty. Indicate whether "Own manufactured Item" or "Bought Out Item" Indicate country of Origin

B1 Earth work in surface excavation by mechanical means for lowering & leveling the ground for all works other than foundation in all kinds of soils & upto depth not exceeding 300mm as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenances required to complete the work. (V1/Pg8/1.12) Cum 95.00

B2 Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work In all kinds of soils Depth upto 3 m (V1/Pg8/1.14.1) Cum 362.00

B3 Construction of Embankment by excavating the available approved Gravel/Murrum deposited at a place or borrow pits during or prior excavation with all lifts and lead, transportation to site, spreading, grading to required slope and compacting to meet the requirement complete as per specifications, including cost of labour,rolling, water,all materials,usage& all other appurtenaces required to complete the work. (V1/Pg7/1.8) Cum 251.00

B4 Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. Mix 1:3:6 Using 20 mm nominal size graded crushed coarse aggregates (V1/Pg15/2.1.4) Cum 46.00

B5 Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing, form work, centering & scaffolding and all the other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates For foundation add at 3% (V1/Pg15/2.2.3) Cum 40.00

B6 Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates For cable duct add at 35% (V1/Pg15/2.4.3) Cum 18.00

B7 Steel Fabrication: Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification All other type of structures (V1/Pg18/2.11h) Kgs 4317.00

B8 Providing and fixing Structural Steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge. (V2/Pg77/11.2) Kgs 1802.00

B9 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. (V1/Pg7/1.9) Cum 78.00

B10 Providing PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour with all lead & lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (Contractor will make his own arrangements for procuring water for testing) etc for:PVC pipes 160mm dia., 6 kg/sqcm & class 3 (V5/Pg113/10.1.9) Rmt 80.00

B11 Jelly Spreading (20-25 mm) : Supplying and providing jelly in the station yard of uniform thickness of 100 mm including the cost of materials, labour charges, required tools and plants etc., complete. Work shall be carried out as per the instructions of Engineer in-charge of works as per the standard procedure. (V6/Pg158/1) Sqm 700.00

B12 Providing and constructing load bearing wall with Solid Concrete blocks of size 400x150x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2185 (Part - I) - 2005 and constructed with CM 1:4 as per IS 2572:2005 including cost of all materials, labour, scaffolding and curing, usage charges of machinery etc complete as per specifications (V2/Pg17/6.33) Sqm 13.00

B13 Providing 15 cement plaster on rough side of single or half with cement mortor 1:4 to brick masonary including rounding off corners wherever required smooth rendering, providing and removing scaffolding including codt of material,labo,curing complete as per specificatoins and as per direction of engineer in charge (V2/Pg41/8.2.1) Sqm 76.00

B14 Constructing brick masonry chamber of internal dimension 450x450mm and depth of 600mm (inner dimensions) with modular bricks of CD 75 in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plastering 12 mm thick with cement mortar 1:4, CC 1:2:4 coping 75mm thk for fixing CI cover & frame etc. Excluding the cost of CI frame and cover. Vol-5 I.No.16.10 VP.No-191 Nos. 8.00

B15 Providing and fixing SFRC frame and cover conforming to IS 12592 (part-I)-1988 and IS 12592 (part-II)- 1991 with latest amendment, including cutting slabs to the required size for the opening and fixing the cover in C.C. 1:2:4 and C.M. 1:3 plastering 20 mm thick to all exposed faces, curing for 10 days with all lead and lift with appurtenances. complete Vol-5 P.196,I.no.16.23.1 Set 9.00

B16 Providing and laying water proofing treatment to the Retaining wall area with PU Elastomeric Single component liquid applied, cold applied, moisture cured high tensile elastomeric PU waterproofing membrane having elongation of more than 400% and having solid content of above 90% @ 1.6kg per m2 in 2 coats to achieve final DFT (dry film thickness) of 1mm including prime coat of epoxy primer @150 g/ m2. The cost is inclusive of surface preparation, crack filling, repair of loose mortar etc. completely as per specification & with a 10 years warranty on product & work from certified manufacturers as per the direction of the Engineer In charge. [for oil pit] (V2/pg134/15.4) Sqm 13.00

B17 Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing, form work, centering & scaffolding and all other appurtenances required to complete the work as per technical specifications. M 40 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (V1/Pg17/2.5.5) Cum 36.00

B18 Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver/grader in sub-base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density (V3/Pg26/4.1.7) Cum 40.00

B19 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (V2/pg48/8.40) Sqm 24.00

B20 Providing Size Stone masonry with hard stone in foundation & plinth with Cement mortar 1:6 (1 cement : 6 coarse sand) (V2/Pg9/5.4) Cum 24.00

B21 Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates. For column add at 70% (V1/Pg16/2.5.2) Cum 3.00

B22 Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineerin-charge. (Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade) (V2/pg95/11.59) Sqm 180.00

B23 Fencing with G.I. barbed wire R.C.C. post placed at required distance, embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post one side only, provided with horizontal lines and two diagonals of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples on wooden plugs or G.I. binding wire tied to 6 mm bar nibs fixed while casting the post (cost of R.C.C. posts, struts, earth work and concrete to be paid for separately) :- Payment to be made per metre cost of total length of barbed wire used. (V2/Pg95/11.56) Rmt 225.00

B24 Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 g/L and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives, New work (Two coats applied @ 1.43 L/ 10 m². Over and including priming coat of exterior primer applied @ 0.90 L/10 m² with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. (V2/Pg41/8.32) Sqm 203.00

B25 Providing Flush/ Ruled pointing: Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) after raking joints to depth nicely lining, including cost of materials, labour, curing as per specifications and as per directions of Engineer-in-charge. (V2/Pg44/8.19.1) Sqm 68.00

B26 Providing S&S RCC SPUN / VIBRATED CAST PIPES (REINFORCED) pipes NP-3 Class conforming to IS:458-1988 with latest amentments using ordinary portland cement, for sanitary works and conveying to work site, rolling and lowering into trenches, laying true to line and level including loading and unloading at both destinations and jointing of pipes and specials, perfect linking of joints with jack to correct position including cost of jointing materials, i.e, rubber rings conforming to IS: 5382 for S&S RCC pipes, with all leads and lifts as directed and giving necessary hydraulic test as per ISS to the required pressure and commissioning etc. complete. (Contractor will make his own arrangements for procuring water for testing). Before the execution of the work, the contractor shall carry out the survey. RCC NP3 Class pipe of 300 mm dia. (for road crossing) (V5/Pg18/713) m 40.00

Place Designation

Name of Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-5 COMMERCIAL DEVIATION

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

Please fill Only in the Light Blue Couloured Cell.

Please key in the SlNo.,Section , Clause , Description as given in bid sheets and finally your Statement of Deviation/Variations.

This Sheet would be opened at the Techno-Commercial Opening. Please refer Vendor Manual attached for further details.

For any further assistance for submitting your bids please call up KPTCL Office.

We agree to provide all original Documents in support of the information provided for verification upon request. (Key in as YES in the space provided)

We understand that the electonic bid submitted by us is a valid offer in accordance with IT Act. (Key in as YES in the space provided)

We are fully aware of the electronic bid formalities and abide by the same. (Key in as YES in the space provided)

If you are not deviating from any of the clauses mentioned please key in as 'NO DEVIATION' in the space provided.

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

I/we have read each of the Clauses mentioned in INVITATION FOR TENDERS , INSTRUCTION TO TENDERERS , CONDITIONS OF CONTRACT, SPECIAL CONDITIONS OF CONTRACT and COMMERCIAL TERMS AND CONDITIONS and all the sections of Bid documents.

The following are the commercial Deviations and Variations from and exceptions to the Specifications and documents for

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

These deviations and variations are exhaustive. Except these deviations, the entire work shall be performed as per your specifications and documents.

Sl. NO. SECTION CLAUSE NO. DESC. AS PER SPECIFICATION STATEMENT OF DEVIATIONS/VARIATIONS

Note : Deviations specified elsewhere in the specification will not be considered.

Place Designation

Name of the company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-6 : TECHNICAL DEVIATION

SHEET FOR TECHNO-COMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

Please key in the SlNo., Section , Clause , Description as given in Bid sheets and finally your Statement of Deviation/Variations.

This Sheet would be opened at the Techno-Commercial Opening.

For any further assistance for submitting your bids please call up KPTCL office. Please fill only in the blue coloured cells.

We agree to provide all original Documents in support of the information provided for verification upon request. (Key in as YES in the space provided)

We understand that the electonic bid submitted by us is a valid offer in accordance with IT Act. (Key in as YES in the space provided)

We are fully aware of the electronic bid formalities and abide by the same. (Key in as YES in the space provided)

If you are not deviating from any of the clauses mentioned please key in as 'NO DEVIATION' in the space provided.

Bidder's Name & Address alongwith GSTIN no. : TO,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

The following are the Technical Deviations and Variations from and exceptions to the Specifications and documents for

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

These deviations and variations are exhaustive.Except these deiviations and variations, the entire work shall be performed as per your specification and documents.

Sl. NO. SECTION CLAUSE NO. DESC. AS PER SPECIFICATION STATEMENT OF DEVIATIONS/VARIATIONS

Note : Deviations specified elsewhere in the specification will not be considered.

Place Designation

Name of the company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE 7(List of special tools and tackles )

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

Bidder's Name & Address alongwith GSTIN no. : TO,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

List of special tools and tackles the price of which is included in bid price.

Sl. No. For equipment Description of item Unit Quantity

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

NOTE: 1 ) SHALL BE UPLOADED WITHOUT PRICES

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

We have uploaded with our proposal the following additional information.

Sl. No. Brief Description of information Ref. and Page No.

Place Designation

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (1 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

BIDDER'S NAME AND ADDRESS: TO,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

a) * We have submitted bid as individual Bidder. (Key in Individual Bidder )

b) * We have submitted bid in Consortium with the following Bidders. (Key in Consortium ) VOID

Name of Consortium Partner Scope / Participation of each Consortium Partner

(* Fill-up whichever is applicable)

1.0 GENERAL INFORMATION

The Bidder, bidding for this package are requested to complete the information in the following form.

Sl. No. Particulars Bidder Details

1 Name of the Firm

2 Address of Head Office / Registered Office GST no.

5 Name of Contact person with Designation

6 Place of Incorporation/Registration

7 Year of Incorporation/Registration

8 Constitution or legal status of Tenderer [Upload copy]

9 Place of Registration [Upload copy]

10 Principal place of business

2.0 We are furnishing the following details/documents in support of Qualifying requirement for above mentioned project

Sl.No. Bidder Details Indicate Yes/No In case of Consortium -VOID

(a) Written power of attorney of the signatory on the bid to commit the bidder.

1 Uploaded / Not

(b) Certificate of Registration of the Company. Please mention the date of incorporation of the company

1 Uploaded / Not

(c ) Valid Super Grade Electrical Contractor’s License issued by the Government of Karnataka as on the date of techno commercial Bid opening. Please mention the date of expiry of the License certificate issued by GOK/ Undertaking to this effect

1 Uploaded / Not

(d) Self declaration regarding Litigation w.r.t KPTCL contracts over the last five years (refer IFT)

1 Uploaded / Not

(e) Self declaration for ‘not being disqualified regarding non-performance in any of the Government utilities in the past five years’. (refer IFT)

1 Uploaded / Not

(f) An undertaking to source the supply of equipment/ material from KPTCL approved vendors only as per QR for Vendor registration, available in the KPTCL website ie., kptcl.karnataka.gov.in, Link Tender and Procurement-Application for Vendor.

1 Uploaded / Not

(g) Self declaration regarding no action against the bidder have been taken by KPTCL in respect of Risk & Cost clause

1 Uploaded / Not

(h) Self declaration regarding 'Eligibility clauses in respect of restrictions on procurement from a bidder of a country which shares a land border with India as per Annexure-XVI

1 Uploaded / Not

(i) Self declaration regarding RESTRICTIONS ON SOURCING OF EQUIPMENTS/MATERIALS BY THE BIDDER FROM A VENDOR OF A COUNTRY WHICH SHARES A LAND BORDER WITH INDIA as per Annexure -XVII

1 Uploaded / Not

Section 3 : 1.3 Work performed of similar nature in the last Ten years of Bidder as per Clause No: 3.2 (b) (i) of ITT

Project Name Name & Address of the Employer Description of Work Voltage class Number of Sub-Stations/TBs/Length of the Line Contract Number Value of contract Rs. Lakh Date of issue of work order Specified period of completion Actual date of commissioning Remarks explaining reasons for delay in commisioning of work

Note : 1 . The documentary proof of fulfilling the qualifying requirements shall be uploaded along with the bid. The bidder shall upload the P.O,LOI/LOA, DWA, Work done, Performance Certificates issued by the end users not below the rank of Executive/ Divisional Engineer along with the bid.

2. The qualifying experience of the Bidder who is having qualifying experience shall be furnished in the above performa and Documentary Proof in support of above shall be uploaded in the form of certificates issued by authorized officers of concerned organisations.

3. IF this sheet is insufficient for furnishing the qualifying experience of the Bidder then similar sheets shall be seperately uploaded.

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (2 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

BIDDER'S NAME AND ADDRESS: TO,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

Section 3 : 1.5 Information on works for which Tenders have been submitted and works which are yet to be completed as on the date of this Tender of a Bidder

(A) Existing commitments and on-going works:

Description of work Place & State Contract No & Date Name and Address of Employer Value of contract (Rs. Lakh) Stipulated period of cof Completion Value of works remaining to be completed ( Rs.Lakhs) (Attach Certificates from Engineers –in- Charge) Anticipated date of commissioning

Ex-Works GST Total(Ex-works+GST)

Note:Attach Certificates from Engineers –in- Charge

B)Works for which Tenders already submitted

Description of work Place & State Name and Address of Employer Estimated value of works (Rs. Lakh) Stipulated period of Completion Date when decision is expected Remarks if any

Ex-works GST Total(Ex-works+GST)

i) The statements showing the value of existing commitments and on-going works as well as the stipulated period of completion remaining for each of the works listed should be countersigned by the Employer in charge, not below the rank of an Executive Engineer or equivalent. OR The statements showing the value of existing commitments and on-going works as well as the stipulated period of completion remaining for each of the works listed should be verified and certified by Chartered Accountant/ Cost Auditor. However, the Bidder has to upload the PO/Work Award copies for existing commitments and on-going works

ii) A self-declaration is to be uploaded by the bidder stating that "the information with regard to assessed available tender capacity (Works on Hand) furnished are correct”.

iii. Bidders shall furnish Certificate from Chartered Accountants for split details of Ex-works values and GST of Contract values of the works in the prescribed format as at Clause No. 1.5 of Section-3: Qualification Information

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (3 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

BIDDER'S NAME AND ADDRESS: TO,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

Following is the list of major supplied subsation equipments/accessories which are type tested and designed, manufactured by us in accordance with internationally recognised standards.

Sl. No. Item rating, type and Designation Qty Customer Date of Order Date of Supply Date of Commissioning Ref. of Cusomer's certificate of successful operation enclosed Ref. of layout & Customer's certificae for successful commission

Note: Documentary Proof in support of above shall be uploaded in the form of certificates issued by authorized officers of concerned organisations. .

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (4 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

Bidder's Name & Address alongwith GSTIN no. : To

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

Section 3 : 1.7 Reports on the financial standing of the tenderer, such as Profit and Loss Statements and Auditor’s reports in the preceeding last five years, Audited Financial statements i.e Balance sheets, P&L statements, Turnover certificates duly certified by chartered Accountant as documentary evidence shall be uploaded.

SLNo. Particulars Year Bidder Consortium Member - VOID

Mention Year Turnover excluding GST (in Rs.) GST Amount (in case GST is included in Turnover) (in Rs.) Turnover including GST (in Rs.) Mention Year Turnover excluding GST (in Rs.) GST Amount (in case GST is included in Turnover) (in Rs.) Turnover including GST (in Rs.)

Names of the constituent Firm VOID

1 Annual turn over for the last Five years Year(1) 2019-20 2020-21

2 Liquid Assets / Credit availability or access to evidence of assets

3 Whether Audited Balance sheets and Profit & Loss statement are enclosed for the last Five Years ? (yes/No)

4 Whether Bankers certificate enclosed for credit facilities? (Yes/No)

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 9 (5 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

BIDDER'S NAME AND ADDRESS: TO,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

The information to be filled in by the Tenderer hereunder will be used for purposes of computing Tender capacity as provided for in Clause 3 of the Instructions to Tenderers. This information will not be incorporated in the Contract.

1.1 Constitution or legal status of Tenderer [Upload copy]

Place of Registration [Upload copy]

Principal place of business

Section - 3: 1.2 Total value of works executed (KPTCL & NON KPTCL works) and payments received in the last Five years (in Rs. Lakhs)

1.2 Total value of works executed (KPTCL & NON KPTCL works) and payments received in the last five years (in Rs. Lakhs) of Bidder Financial Year Details

KPTCL works Non KPTCL works

Total value of works in Rs. Lakh Total value of works in Rs. Lakh

Note: Attach relevant Certificate/s from Chartered Accountant.

Section 3: 1.9 Name, address, telephone number & e-mail id of the Tenderers' bankers who may provide references if contacted by the Employer:

1.9 Sl.No Name, address, telephone number & e-mail id of the Tenderers' bankers

Section 3: 1.12 Information on litigations in which the Tenderer is involved:

Other Party(ies) Employer Details of Dispute Amount involved Remarks showing Present Status

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-10 (1 of 3) Details of Tools and Plants available

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

BIDDER'S NAME AND ADDRESS: To

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

Following are the details of the Tools and Plants available with us.

Sl. No. Description Quantity Make Present Location / Project Remarks (if any)

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE 10 (2 of 3) Details of Technical staff employed

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

BIDDER'S NAME AND ADDRESS: To

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

Section 3: 1.8 Qualification and experience of the key technical and management personnel in permanent employment with the tenderer and those that are proposed to be deployed on this contract, if awarded

Sl. No. Name of the employee Designation Branch (Degree/Diploma) Year of Passing Since when employed in erection division Past Experience

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE 10 (3 of 3 )

SHEET FOR TECHNOCOMMERCIAL OPENING

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

KPTCL/2026-27/SS/ Vadavatti Enhancement.

BIDDER'S NAME AND ADDRESS:

We propose the following deployment of manpower for the substation and Line package.

Sl. No. Category MONTHS AFTER PLACEMENT OF AWARD LETTER

1 Project manager

2 Sr. Project Manager

5 Skilled labour

6 No skilled labour

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-11 (A) : COMPLETION SCHEDULE FOR STATION/TERMINAL BAYS

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

Bidders Name and Address: To,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

We hereby declare that following schedules shall be followed by us for the above work. The period of various activities from the date of placement of award letter shall be as follows

SL.NO Activity STATION PORTION

Commencement Completion

1 Detailed engineering

2 Procurement of bought out items / raw materials

3 Manufacturing & Testing

5 Setting up of site office, Sheds & stores etc.

7 Concreting for

a)Structure Foundations

b)Equipment and mounting structure foundadions

c)Cable trenches

2. Installation

8 Receipt(at site) of

a)Main equipment / spares

c)Insulators & Hardwares

d)Clamps & Connectors

e)Marshalling kiosks

f)Cables & Cabling Materials

a)Main structures

b)Equipment support structures

10 Equipment Erection

12 Bus bar erection

15 Completion of testing and ready for commissioning

16 Commissioning

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-11B : COMPLETION SCHEDULE FOR TRANSMISSION LINES

SHEET FOR TECHNOCOMMERCIAL OPENING

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Bidders Name and Address: To,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

We hereby declare that following shedules shall be followed by us for the above work. The period of various activities from the date of placement of award letter shall be as follows.

SL.NO Activity Construction of Transmission Line

Commencement Completion

1 Submission of Drawings

2 Completion of detailed engineering

3 Commencement of Manufacturing

4 Completion of Manufacturing VOID

5 Readiness for testing

6 Readiness for Shipment

7 Receipt at Site

8 Completion of Shipment

1 Detailed Survey

2 Setting up of site office, sheds and stores etc.

3 Exacavation for foundations.

4 Foundations and other Civil Works

5 Erection of Tower alongwith accessories

6 Stringing of conductor/ groundwire alongwith accessories

7 Testing , Commissioning and Handing over.

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 12 TYPE TESTS & TEST CHARGES OF EQUIPMENT/MATERIALS

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

BIDDERS SHALL INDICATE VARIOUS TYPE TESTS IN LIGHT BLUE COLOURED CELLS

ALL THE TYPE TESTS APPLICABLE FOR EACH OF THE EQUIPMENTS SHALL BE INCLUDED.

Bidders Name and Address To,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

SL.No Details of Equipments Type Test Test Charges ( in Rs )

1 Power Transformers:

2 SF6 Circuit Breakers:

3 Surge Arrestors

5 Control & Relay Panels / Relay & Protection Panels

6 L.T. A.C Panel

7 Station Battery

8 Station Battery Charger

9 1.1KV Power Cables

10 1.1kV Copper Control cables

11 11kV U.G Cable

12 Insulators a) 90KN Disc Insulator Strings

13 Equipment / Station Structures

14 Aluminium pipe and Clamps

15 Hardware Materials

16 Yard lighting equipments

17 Fire Fighting equipments

18 AC DISTRIBUTION BOX

19 DC DISTRIBUTION BOX

21 Auxiliary Transformer

NOTE: The Type Test / Special Tests, if repeated at the insistance of owner, the applicable testing charges shall be paid by the successful Bidder upfront to the laboratory and the same shall be reimbursable by KPTCL as per actuals on submission of Bills along with proof of payment and on successful completion of all the Type Tests, specified and on approval of the same by the owner. In case equipment/material fails in the type tests during testing then the testing charges paid by the Bidder to the laboratory will not be reimbursed by KPTCL. The above Clause is applicable for all the equipments/materials, in case, the Type Test / Special Tests, are repeated at the insistance of owner(KPTCL).

Place Printed Name

Karnataka Power Transmission Corporation Limited

Schedule -13-List of Optional Spares

SHEET FOR TECHNOCOMMERCIAL OPENING

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

KPTCL/2026-27/SS/ Vadavatti Enhancement.

BIDDERS SHALL NOTE THAT QUANTITIES INDICATED IN THE ITEM_WISE FINANCIAL BID OFFER SHALL BE INDICATED HERE ALSO.

Bidders Name and Address

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

List of optional spares required to meet the specified performance for a period of three years

Sl. No. For Equipments Details of item Unit Quantity

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 14-Guaranteed Losses :

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

Bidders Name and Address along with GSTIN No.: To,

The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

Dear Sir, i) We Declare that the ratings and performance figures of the transformer furnished by us under the Turnkey Package are Guaranteed. We further declare that in the event of any deficiencies in meeting the guarantees in repect of the characteristics mentioned below as established after conducting the factory test, you may at your discretion,reject or accept the equipment after assessing the liquidated damages as specified in relevant clause of Bid Document.

Equipment Guaranteed Losses at rated output(KW)

Max No Load loss at rated voltage and rated frequency Max Load loss at rated current and frequency and at 75 deg C at principal tap Max I2 R loss at rated current and frequency and at 75 deg C at principal tap Max Auxiliary loss at rated voltage and frequency for Power Transformer

20MVA, 110/33-11kV Power Transformer

Note:(i) Refer Technical Specifications (ii)The loss quoted shall be consistent in Schedule 14 and GTPs(DRS)of Power Transformer

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

LIST OF VENDORS

SHEET FOR TECHNOCOMMERCIAL OPENING

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

KPTCL/2026-27/SS/ Vadavatti Enhancement.

BIDDERS NAME AND ADDRESS The Chief Engineer Electy, Transmission (Operations) Zone, KPTCL, Kalaburagi

Sl. No. EQUIPMENT/ MATERIAL NAME OF THE VENDOR

VENDOR 1 VENDOR 2 VENDOR 3 VENDOR 4

1 Power Transformer 20MVA, 110/33-11kV Transformer

2 SF6 Circuit Breakers: 145kV

3 SURGE ARRESTERS

4 Control & Relay Panels / Relay & Protection PANELS

5 Station / Equipment Support structures

6 Aluminium pipe and Clamps

7 ACSR CONDUCTOR

9 Solid Core Insulator

10 Disc Insulator Strings

11 Insulator Hardware Clamps & Power connectors

12 Auxiliary Transformer

14 1.1kV POWER CABLES

15 AC DISTRIBUTION BOX

16 DC DISTRIBUTION BOX

18 BATTERY CHARGER

19 CONTROL CABLES

20 11KV Switchgear

21 11kV UG CABLE

22 FIRE FIGHTING EQUIPMENTS

23 Illumination Equipments / Fixtures

25 Tower Accessories

26 Insulator Hard Wares

27 Conductor Accessories

28 Earth Wire Accessories

Note : Any Other Materials name & its vendors are to be entered.

Place Designation

Name of the Company

SCHEDULE-16 : NO DEVIATION CERTIFICATE (ANNEXURE-I)

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

NOTE: SCHEDULE DULY SIGNED BY THE AUTHORIZED PERSON SHALL BE UPLOADED

With reference to our Bid Proposal No dated

We hereby confirm that we have read the provisions of the contract, the stipulation of these clause are acceptable to us,

and we have not taken any deviation whatsoever to these clauses:

a) Terms of payment Clause No. 37 of Section-5,Conditions of Contract (CC) and Clause No.8 of Special Conditions of Contrac (SCC)

b) EMD/Bid Security Clause No. 6, Section :1, Invitation for Tenders (IFT) and Clause No. 13, Section :2, Instruction to Tenderer (ITT)

c) Contract Performance Guarantee Clause No. 29 of Section:2, Instruction to Tenderers (ITT).

d) Penalty for delay Clause No. 41 of Section-5 : Conditions of Contract (CC).

e) Price Basis/ Price adjustment Clause No. 40 of Section-5 :Conditions of Contract (CC).

f) Defects Liability Period/Guarantee Clause No. 10 of Section-5 Special Conditions of Contract (SCC)

g) Work Schedule Clause No.17 of Section:5 Conditions of Contract (CC)

h) Taxes and Duties Clause No. 11.11 of Section-2: Instruction to Tenderers (ITT).

We further confirm that any deviation to the above clauses at SI.No. (a) to (h) found anywhere in our bid proposal, implicit or explicit, shall stand unconditionally withdrawn, without any cost implication whatsoever to KPTCL.

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE-17 FORM FOR BID SECURITY/EMD (ANNEXURE-II) (To be stamped on Rs.300/- Non-Judicial stamp paper in accordance with KPTCL Circular No. KPTCL/GMT/CIVIL (B7)/35/2024-MANAGER ESTATE (E-106992) dated 02.03.2024)

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

NOTE: SCHEDULE DULY SIGNED BY THE AUTHORIZED PERSON SHALL BE UPLOADED AND SENT ALONG WITH ORIGINAL BANK GUARANTEE AND ORIGINAL DD (TOWARDS BID GUARANTEE ) TO CHIEF GENERAL MANAGER (TECH),KPTCL BANGALORE SO AS TO REACH AFTER THE LAST SUBMISSION DATE & ON OR BEFORE THE DATE & TIME OF OPENING TECHNO COMMERCIAL BIDS.

Ref No. Bank Guarantee No.

In accordance with Invitation to Bid under your specification

No. M/s having its Registered /

Head Office at (hereinafter called the 'Bidder') wish

to participate in the said Bid or and you, as a special favour have agreed

to accept an irrevocable and unconditional bank guarantee for an amount of

valid up to on behalf of Bidder in lieu of the Bid deposit required to be made

by the Bidder as a condition predecent for participation in the said Bid,in addition to the Demand draft No.

we the Bank at having our Head office at

(local address) guarantee and undertake to pay immediately on demand by Karnataka Power Transmission Corporation

the amount of (in figures and words)

without any reservation, protest, demur and recourse. Any such demand made by said `Owner' shall be conclusive and binding on us irrespective of any dispute or difference raised by the Bidder.

This Guarantee shall be irrevocable and shall remain valid up to and including

If any further extension of this guarantee is required, the same shall be extended to such required period (not exceeding one year) on receiving instructions

from M/s on whose behalf this guarantee is issued.

This Guarantee has been issued using SFMS Platform and the requisite communication in this regard has been forwarded to the Beneficiary Bank.

In witness whereof the Bank, through its authorised officer, has set its hand and stamp on this

Signature Signature

Official Addressess Designation with Bank Stamp.

Attorney as per Power of Attorney No.

Note : 1) Both the Bank Guarantee and Demand Draft shall be scanned and uploaded along with Electronic sheets. 2) This date shall be Forty Five (45) days after the last date for which the bid is valid.

Karnataka Power Transmission Corporation Limited

SCHEDULE-18 PROFORMA OF LETTER OF UNDERTAKINGS (ANNEXURE-V)

SHEET FOR TECHNOCOMMERCIAL OPENING

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

NOTE: SCHEDULE DULY SIGNED BY THE AUTHORIZED PERSON SHALL BE UPLOADED

(To be executed on Non-Judicial paper of RequisiteValue)

1. I*/We* have read and examined the following bid documents relating to the

(full Scope of Work)

a) Notice Inviitng Tender

b) Conditions of Contract containing section 'Invitation for Tenders’, 'Instructions to Tenderers’, ‘Conditions of Contract’ and Contract Data.

c) Special Conditions of Contract along with Annexure to

d) Drawings No.

e) Technical Specifications

2 . I / We hereby submit our Bid and undertake to keep our Bid Valid for a period of One Hundred and Eighty days (180 days) from the Last date of bid submission as notified (either original or extended). I*/We* hereby further undertake that during said period I/We shall not vary/alter or revoke my/our Bid.

This undertaking is in consideration of KPTCL agreeing to open my/ our Bid and consider and evaluate the same for the purpose of award of Work in terms of provisions of clause entitled "Award of Construct" 'cl.no. 26 of Section ITT and cl.no. 18 of SCC of the Bid Documents.

Should this bid be accepted, I*/We* also agree to abide by and fulfil all the terms, conditions of provision of the above mentioned bid.

Signature along with Seal of Co.

(Duly Authorised to sign the Tender on Behalf of the Contractor.)

NAME OF THE COMPANY (in Block Letters)

SIGNATURE Date and Postal Address

DATE Telegraphic Address

NAME AND ADDRESS Telephone No.

Karnataka Power Transmission Corporation Limited

SCHEDULE-19 CONSORTIUM AGREEMENT ON NON JUDICIAL STAMP PAPER OF Rs.500/-(ANNEXURE -XIII) - VOID

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

KPTCL/2026-27/SS/ Vadavatti Enhancement.

NOTE: SCHEDULE DULY SIGNED BY THE AUTHORIZED PERSON SHALL BE UPLOADED.

CONSORTIUM AGREEMENT AMONGST M/s M/s

For Bid Specification No. OF KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

This consortium agreement executed on this day Month of Two thousand Twenty Four

amongst M/s a company incorporated under the laws of (Country) and having its registered office at

(hereinafter called the "Lead Company" which expression shall include its successors ,executors and permitted assigns),

M/s a company incorporated under the laws of (Country) and having its registered office at

(hereinafter called the "Constituent Company" which expressions shall include its successors,executors and permitted assigns)

for the purpose of making a bid and entering into a contract (In case of award) against the specification no.

For NAME OF THE WORK

for Karnataka Power Transmission Corporation Ltd. having its registered office at Kaveri Bhavan , Bangalore 560 009 , Karnataka (hereinafter called the "Owner"). The leader of the consortium shall abide by the general terms and conditions specified by the Purchaser. WHEREAS the Owner invited bids as per the above mentioned specifications for the design, manufacture, supply and erection, testing and commissioning of Equipments/Materials stipulated in the bidding documents under subject package

NAME OF THE WORK

AND WHEREAS Section-I ( Volume-1: Clause No. 11:- Qualifying Requirement), forming part of the bidding documents, stipulates that a consortium meeting the requirements of Section-I, ( Invitation of Bid) applicable may bid, provided the Consortium fulfills all other requirements of specification and in such a case, the Bid shall be signed by the members so as to legally bind the members and who will be jointly and severally liable to perform the Contract and all obligations hereunder.

The above clause further states that the consortium agreement shall be attached to the bid and the contract performance guarantee will be as per the format enclosed with the bidding document without any restriction or liability for either party.

AND WHEREAS the bid has been submitted to the Owner vide proposal No dated

by Lead Company based on the Constituent agreement between all the consortium under these presents and the bid in accordance with the requirements of Specifications (Qualification Requirements).

NOW THEREFORE THIS UNDERTAKING WITNESSETH AS UNDER:

In consideration of the above premises and agreements all the partners to this consortium members do hereby now agree as follows:

1 In Consideration of the award of the Contract by the Owner to the Consortium members, we , the members to the consortium agreement do hereby agree that M/s

shall act as Lead Company and further declare and confirm that we shall jointly and severally be bound up to the Owner for the successful performance of the contract and shall be fully responsible for the design, manufacture, supply and successful performance of the equipments in accordance with the Contract.

2 In case of any breach of the said contract by the Lead company or other constituent of the Consortium agreement, the Lead company do hereby agree to be fully responsible for the successful performance of the contract and to carryout all the obligations and responsibilities under the contract in accordance with the requirements of the Contract

3 Further, if the Owner suffers any loss or damage on account of any breach in the contract or any shortfall in the performance of the equipment in meeting the performance guaranteed as per the specification in terms of the contract, the Lead company of these presents undertake to promptly make good such loss or damages caused to the Owner, on its demand without any demur. It shall not be necessary or obligatory for the Owner to proceed against Lead Partner to these presents before proceeding against or dealing with the other Partner (s).

4 The Financial liability of the members of the consortium agreement to the Owner, with respect to any of the claims arising out of performance or non-performance of the obligations set forth in the said agreement, read in conjunction with the relevant conditions of the contract shall, however not be limited in any way so as to restrict or limit the liabilities of any of the members of the agreement.

5 It is expressly understood and agreed between the members to this consortium agreement that the responsibilities and obligations of each of the partners shall be as delineated hereunder (To be incorporated suitably by the member to this agreement). However, each member of the consortium will be severally and jointly responsible for the faithful performance of the contract. It is further agreed by the member that the above sharing of responsibilities and obligations shall not in any way be a limitation of joint and several responsibilities of the members under this contract.

Sl.No. Name of the Lead Bidder/Consortium Partner. Scope of the work/Participation

We further declare ourselves bound to execute our scope of work/participation as stated above;

6 This Consortium agreement shall be constructed and interpreted in accordance with the laws of India and the courts of Bangalore shall have the exclusive jurisdiction in all matters arising there under.

7 In case of an award of a Contract, we the Consortium members do hereby agree that we shall be jointly & severally responsible for the works respectively executed and Lead company shall furnishing a contract performance security from a bank in favor of the PURCHASER in the forms acceptable to purchaser for value of Five percent (5%) of the total Contract Price plus additional security for unbalanced tenders in accordance with Clause 25.5 & 29 of ITT and Clause 43 of the CC (Conditions of Contract).

8 It is further agreed that the Consortium agreement shall be irrevocable and shall form an integral part of the contract, and shall continue to be enforceable till the owner discharges the same. It shall be effective from the date first mentioned above for all purposes and intents.

IN WITNESS WHEREOF the partners to the Consortium have through their authorized representatives executed these presents and affixed Common seals of their companies, on the day, month and year first mentioned above.

WITNESS for Lead Company

(Signature) (Signature of the authorized representative)

(Name in Block Letters) (Name)

Designation (Designation)

Common Seal of the Company

2 ( For Constituent 1)

(Signature of the authorized representative)

(Name in Block Letters) (Name)

Designation Common Seal of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE-20 POWER OF ATTORNEY (ANNEXURE-XI)

KPTCL/2026-27/SS/ Vadavatti Enhancement.

Balance work of , Enhancement of 1X10MVA, 110/11kV Power Transformer by 1X20MVA, 110/11kV Power Transformer at 110/11kV Vadavatti Sub-station in Raichur Taluk and District-on Partial Turnkey Basis, including supply of equipments/materials, erection testing and commissioning on PTK basis (Major materials such as 11kV Switchgear will be supplied by KPTCL). -Reg

NOTE: SCHEDULE DULY SIGNED BY THE AUTHORIZED PERSON SHALL BE UPLOADED.

POWER OF ATTORNEY

(To be stamped on Rs.500/- Non Judicial stamp paper in accordance with KPTCL Circular No. KPTCL/GMT/CIVIL (B7)/35/2024-MANAGER ESTATE (E-106992) dated 02.03.2024)

KNOW ALL MEN BY THESE PRESENTS that we

a Company incorporated

under the laws of

and having its Registered Office / Head Office at

"Manufacturer / Bidder" which expression shall unless repugnant to the

Context or meanig thereof, include its successors, administrators and assigns)

acting through Mr its constitute, nominate and appoint

M/s a Company incorporated under the laws of

and having its Registered / Head Office at

as its duly constituted lawful Attorney (hereinafter called "Attorney"

or "Authorized Representative") to exercise all or any of the powers for and on

behalf of the "Manufacturer / Bidder" in regard to Specification No.

the bids for which have been invited by

(Address "Owner") to undertake the following acts:

i. To submit proposal and participate in the aforesaid Bid Specification of the Owner on behalf of the "Manufacturer / Bidder".

ii. To negotiate with the "Owner" the terms and conditions including price for award of the contract pursuant to the aforesaid Bid and to sign the contract with the "Owner" for and on behalf of the Manufacturer / Bidder.

iii. To receive accept and execute the contract for and on behalf of the "Manufacturer / Bidder".

iv. To do any other act or submit any document related to the above.

It is expressly understood that the Power of Attorney shall remain valid, binding and irrecoverable till submission of the Contract performance guarantee in terms of the Contract. The "Manufacturer / Bidder" hereby agrees and undertakes to ratify and confirm all the whatsoever the said "Attorney" / "Authorised Representative" quotes in the Bid, negotiates and signs the contract with the "Owner" and / or purports to act on behalf of the "Manufacturer / Bidder" by virtue of this Power of Attorney and the same shall bind the "Manufacturer / Bidder" as if done by itself.

IN WITNESS WHEREOF THE "Manufacturer / Bidder" has executed these presents at

on this day of under

the Common Seal of the Manufacturer company / Bidder.

Specimen Signature of Attorney Holder

(Name & Designation)

For and on behalf of

Common Seal of the above Manufacturer/Bidder

Has been affixed thereto in the presence of :