Construction of New boys hostel for Vikasati Jati (For 100 person Capacity) at Botad, Tal. - Botad, Dist. - Botad

Name Of Work : Construction of New boys hostel for Vikasati Jati (For

100 person Capacity) at Botad, Tal. - Botad, Dist. - Botad.

Bill Of Quantity

Quantities Estimated Total amount

Quantities Estimated Total amount

estimated but rates. according to

Sr.no. Description of item Unit

may be more estimated

or less quantities.

Excavation for foundation upto 1.5 m depth including sorting out and

1 stacking of useful materials and disposing off the excavated stuff upto 50 1487.20 Cu.M. 157.16

Meter lead.(B) Dense or Hard soil

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting

out and stacking of useful materials and disposing off the excavated

2 stuff upto 50 Meter lead.(B) Dense or Hard soil 1230.20 Cu.M. 170.50

Excavation for foundation for depth from 3.0 m to 5.0 m including sorting

out and stacking of useful materials and disposing off the excavated

3 stuff upto 50 Meter lead.(D) Soft rock not requiring Blasting 17.20 Cu.M. 323.81

Filling in foundation and plinth with sand in layers of 20 cm. Thickness

4 including watering ramming and consolidating etc. comp. 78.60 Cu.M. 481.80

Filling available excavated Earth (Excluding Rock ) in trench plinth side of

foundation . in layer not excluding 20 cm in depth consolidation each

5 deposited layer by ramming and watering etc. complete 1936.20 Cu.M. 136.92

Filling foundation and plinth with murrum or selected soil in layer of 20 cm in

6 thickness including, ramming watering and consolidating etc. complete 667.80 Cu.M. 301.78

Applying general insecticide pest control treatment to floors, cupboards etc

including labour material etc. complete. Using Heptachloride 20 EC. As Per

6113_pests Consentration Weight 0.50 percent is recommended one litre

chemical emulsion dillute with 39 liter of water will give. Total dillute

concrentration will be 40 litre inclusive of one litre chemical emulsion

appication 0.5 Litre chemical / Sqm of surface is recommended as per I.S

Providing and laying cement concrete Work 1:2:4 (1-Cement :2-Coarse sand :

4-Grade stone aggregates 20 mm nominal size) and Curing complete excliding

8 cost of formwork and reinfoecedment for reinforced concrete work in (A) 95.80 Cu.M. 4581.36

Foundation, Footing, Base or Columns and Mass Concrete

Providing and laying controlled cement concrete M-250 and curing complete

including the cost of form work but excluding the cost of reinforcement for

9 reinforced concrete work in foundation footings, base of columns and mass 181.00 Cu.M. 4879.74

Providing and laying controlled cement concrete M-250 and curing complete

including the cost of form work but excluding the cost of reinforcement for

10 reinforced concrete work in Columns, pillars posts and struts. Column upto 65.90 Cu.M. 7939.28

Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse sand : 6-

11 graded stone aggregates 40 mmnominal size) and curing complete excluding 169.30 Cu.M. 3095.25

cost of formwork in (A) Foundation and Plinth (more than 10 ton)

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

12 reinforced concrete work in Columns, pillars posts and struts G.FLOOR. 66.90 Cu.M. 7906.28

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

13 reinforced concrete work in in Columns, pillars posts and struts For First floor 50.90 Cu.M. 7947.87

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

14 reinforced concrete work in in Columns, pillars posts and struts For Second 25.50 Cu.M. 7989.46

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

15 reinforced concrete work in in Columns, pillars posts and struts For Third floor 1.80 Cu.M. 8031.06

Providing and laying controlled cement concrete M-250 and curing complete

16 including the cost of form work but excluding the cost of reinforcement for 237.30 Cu.M. 6046.65

reinforced concrete work in Ground & Plinth BEAMS.

Providing and laying damp proof course 25 mm thick cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate 10 mm nominal size)

including curing complete as per specification and painting with two coats of

17 hot bitumen of grade 80/100, each coat applied @ 1.5 kg per sqm over the 237.90 Sqm 761.54

dried surface after proper cleaning and preparation, complete as directed by

the Engineer-in-Charge.

Providing and laying controlled cement concrete M-150 and curing complete

18 including the cost of form work but excluding the cost of reinforcement for 132.80 Cu.M. 4311.79

reinforced concrete work in Plinth Slab.

Providing and laying controlled cement concrete M-200 and curing complete

19 including the cost of form work but excluding the cost of reinforcement for 111.20 Cu.M. 6356.15

reinforced concrete work in BEAMS Ground Floor.

Providing and laying controlled cement concrete M-200 and curing complete

20 including the cost of form work but excluding the cost of reinforcement for 114.90 Cu.M. 6397.74

reinforced concrete work in BEAMS for First Floor

Providing and laying controlled cement concrete M-200 and curing complete

21 including the cost of form work but excluding the cost of reinforcement for 49.10 Cu.M. 6439.34

reinforced concrete work in BEAMS for Second Floor

Providing and laying controlled cement concrete M-200 and curing complete

22 including the cost of form work but excluding the cost of reinforcement for 4.10 Cu.M. 6480.93

reinforced concrete work in BEAMS for Third Floor

Providing and laying controlled cement concrete M-200 and curing complete

23 including the cost of form work but excluding the cost of reinforcement for 24.80 Cu.M. 7910.83

reinforced Concrete work in Lintel for Ground Floor

Providing and laying controlled cement concrete M-200 and curing complete

24 including the cost of form work but excluding the cost of reinforcement for 28.40 Cu.M. 7952.42

reinforced Concrete work in Lintel for First Floor

Providing and laying controlled cement concrete M-200 and curing complete

25 including the cost of form work but excluding the cost of reinforcement for 17.60 Cu.M. 7994.01

reinforced Concrete work in Lintel for Second Floor

Providing and laying controlled cement concrete M-200 and curing complete

26 including the cost of form work but excluding the cost of reinforcement for 4.10 Cu.M. 8035.60

reinforced Concrete work in Lintel for Third Floor

Providing and laying controlled cement concrete M-200 and curing complete

27 including the cost of form work but excluding the cost of reinforcement for 2.60 Cu.M. 8077.19

reinforced Concrete work in Chajja for Ground Floor.

Providing and laying controlled cement concrete M-200 and curing complete

28 including the cost of form work but excluding the cost of reinforcement for 4.90 Cu.M. 7315.41

reinforced Concrete work in Chajja for First Floor

Providing and laying controlled cement concrete M-200 and curing complete

29 including the cost of form work but excluding the cost of reinforcement for 2.50 Cu.M. 7357.00

reinforced Concrete work in Chajja for Second Floor

Providing and laying controlled cement concrete M-200 and curing complete

30 including the cost of form work but excluding the cost of reinforcement for 0.10 Cu.M. 7398.59

reinforced Concrete work in Chajja for Third Floor

Providing and laying controlled cement concrete M-200 and curing complete

31 including the cost of form work but excluding the cost of reinforcement for 139.80 Cu.M. 7227.40

reinforced concrete work in SLABS for Ground Floor

Providing and laying controlled cement concrete M-200 and curing complete

32 including the cost of form work but excluding the cost of reinforcement for 146.20 Cu.M. 7268.99

reinforced concrete work in SLABS for First Floor

Providing and laying controlled cement concrete M-200 and curing complete

33 including the cost of form work but excluding the cost of reinforcement for 38.10 Cu.M. 7310.58

reinforced concrete work in SLABS for Second Floor.

Providing and laying controlled cement concrete M-200 and curing complete

34 including the cost of form work but excluding the cost of reinforcement for 4.20 Cu.M. 7352.17

reinforced concrete work in SLABS for Third Floor

Providing and laying controlled cement concrete M-200 and curing complete

35 including the cost of form work but excluding the cost of reinforcement for 6.80 Cu.M. 7931.97

reinforced concrete work in Staircase for Ground Floor.

Providing and laying controlled cement concrete M-200 and curing complete

36 including the cost of form work but excluding the cost of reinforcement for 2.90 Cu.M. 7973.57

reinforced concrete work in Staircase for First Floor

Providing and laying controlled cement concrete M-200 and curing complete

37 including the cost of form work but excluding the cost of reinforcement for 2.90 Cu.M. 8015.16

reinforced concrete work in Staircase for Second Floor

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

38 reinforced concrete work in R.C.C. pardee for Ground Floor 8.60 Cu.M. 11962.62

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

39 reinforced concrete work in R.C.C. pardee for First Floor 3.80 Cu.M. 12004.21

Providing and laying controlled cement concrete M-200 and curing complete

including the cost of form work but excluding the cost of reinforcement for

40 reinforced concrete work in R.C.C. pardee for Second Floor 13.20 Cu.M. 12045.81

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including

41 bending, binding and placing in position complete upto Ground floor level 133556.00 Kg. 77.29

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including

42 bending, binding and placing in position complete For First floor level 47240.00 Kg. 78.34

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including

43 bending, binding and placing in position complete For Second floor level 21062.00 Kg. 79.39

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including

44 bending, binding and placing in position complete For Third floor level 1779.00 Kg. 80.44

Brick work using common Brunt clay building bricks having crushing strength

not less than 35 Kg./Sq.cm.. In foundation and plinth in cement mortar 1:6

45 (1cement : 6 fine sand)(b) Conventional 152.10 Cu.M. 4214.33

Brick work using common Brunt clay building bricks having crushing strength

not less than 35 Kg./Sq.cm.. In super structure above plinth level upto

46 floor two level in cement mortar 1:6 (1cement : 6 fine sand) (b) 230.50 Cu.M. 4496.05

Conventional G.F

Brick work using common Brunt clay building bricks having crushing strength

not less than 35 Kg./Sq.cm.. In super structure above plinth level upto

47 floor two level in cement mortar 1:6 (1cement : 6 fine sand) (b) 151.20 Cu.M. 4538.48

Conventional First floor

Brick work using common Brunt clay building bricks having crushing strength

not less than 35 Kg./Sq.cm.. In super structure above plinth level upto

48 floor two level in cement mortar 1:6 (1cement : 6 fine sand) (b) 81.50 Cu.M. 4580.91

Conventional second floor

Brick work using common Brunt clay building bricks having crushing strength

not less than 35 Kg./Sq.cm.. In super structure above plinth level upto

49 floor two level in cement mortar 1:6 (1cement : 6 fine sand) (b) 25.20 Cu.M. 4623.34

Conventional Third floor

Half brick masonry in common brunt clay building bricks having crushing

strength not less than 35 Kg./Sq.cm.. In cement mortar 1:3 (1cement :

50 coarse sand) with 2 Nos. of 6 mm. Diameter mild steel round bars after every 122.10 Sq.Mt. 750.76

three coarse embedded in cement mortar in super structure. GF

Half brick masonry in common brunt clay building bricks having crushing

strength not less than 35 Kg./Sq.cm.. In cement mortar 1:3 (1cement :

51 coarse sand) with 2 Nos. of 6 mm. Diameter mild steel round bars after every 367.10 Sq.Mt. 756.96

three coarse embedded in cement mortar in super structure above plinth

level First Floor.

Half brick masonry in common brunt clay building bricks having crushing

strength not less than 35 Kg./Sq.cm.. In cement mortar 1:3 (1cement :

52 coarse sand) with 2 Nos. of 6 mm. Diameter mild steel round bars after every 484.60 Sq.Mt. 763.17

three coarse embedded in cement mortar in super structure above plinth

level Second Floor.

Half brick masonry in common brunt clay building bricks having crushing

strength not less than 35 Kg./Sq.cm.. In cement mortar 1:3 (1cement :

53 coarse sand) with 2 Nos. of 6 mm. Diameter mild steel round bars after every 2.70 Sq.Mt. 769.37

three coarse embedded in cement mortar in super structure above plinth

level Third Floor.

Providing and fixing 35 mm thick factory-made solid core flush door single

shutter conforming to IS:12823, Grade-I, Type-I, melamine faced with

54 decorative laminate on both sides and 12 mm thick teak wood lipping on all 64.20 Sq.Mt. 2492.18

edges, including approved hinges, aldrop, handles and fittings, complete as

directed by Engineer-in-Charge.

Providing and fixing 35 mm thick factory-made solid core flush door Double

shutter conforming to IS:12823, Grade-I, Type-I, melamine faced with

55 decorative laminate on both sides and 12 mm thick teak wood lipping on all 83.80 Sq.Mt. 2584.94

edges, including approved hinges, aldrop, handles and fittings, complete as

directed by Engineer-in-Charge.

Providing and fixing 35 mm thick factory-made solid core flush door Double

shutter conforming to IS:12823, Grade-I, Type-I, melamine faced with

decorative laminate on both sides and 12 mm thick teak wood lipping on all

56 edges, including approved hinges, aldrop, handles and fittings, FRP Frame 2.70 Sq.Mt. 3146.05

(100x60mm, moulded, termite & water proof) complete as directed by

Engineer-in-Charge.

Providing and fixing 35 mm thick factory-made solid core flush Main door

Double shutter conforming to IS:12823, Grade-I, Type-I, melamine faced with

57 decorative laminate on both sides and 12 mm thick teak wood lipping on all 7.40 Sq.Mt. 2728.73

edges, including approved hinges, aldrop, handles and fittings, complete as

directed by Engineer-in-Charge.

Providing and fixing FRP of 35mm thick Fiber Glass shutter with 1.5 to 2.0 mm

thick fire retardent grade FRP skin in depressed panel design having extra

reinforcement on sides & edges & in Gel coat finish. The core of the shutter is

to be filled up with injected retardent grade polyurethane foam done in situ

alongwith embedded wooden pieces for stiffening & also taking hinges &

fintures. The whole FRP frame & shutter is to be water proof ,weather proof,

termite proof & resistance to mild acid/alkali. Rates are to be inclusive of S.S

hinges with necessary screws & alluminium fixtures & fastenings.

Providing and fixing window having extruded aluminum Colour anodized

section frame main outer size 95mm x 24mm x 1.17mm @ wt.of 0.738 Kg/mt

horizontal Three track member size 92mm x 31.75mm x 1.30mm,@ Wt.1.07

Kg/mt , vertical member of size 92mm x 31.75mm x 1.50mm @ Wt.

Kg/mt with sliding shutters of horizontal member size 40 mmx18mm x1.29mm

59 @ wt.of 0.456 Kg/mt, vertical member of size 40mm x 18mm x 1.29 mm @ 25.10 Sqmt. 1583.95

wt.of 0.456Kg/mt/ with 5 mm thick transparent bronze colour tinted float

glass with powder coated aluminum fittings and fixtures and transparent

silicon sealant glass fixing to frame as per details etc

Providing and fixing window having extruded aluminum Colour anodized

section frame main outer size 95mm x 24mm x 1.17mm @ wt.of 0.738 Kg/mt

horizontal Two track member size 92mm x 31.75mm x 1.30mm,@ Wt.1.07

Kg/mt , vertical member of size 92mm x 31.75mm x 1.50mm @ Wt.

Kg/mt with sliding shutters of horizontal member size 40 mmx18mm x1.29mm

60 @ wt.of 0.456 Kg/mt, vertical member of size 40mm x 18mm x 1.29 mm @ 136.60 Sqmt. 1713.70

wt.of 0.456Kg/mt/ with 5 mm thick transparent bronze colour tinted float

glass with powder coated aluminum fittings and fixtures and transparent

silicon sealant glass fixing to frame as per details etc

Providing and fixing removable aluminium mosquito net frame with stainless

steel wire mesh (304 grade), powder-coated, fitted in approved colour

matching the existing window frame, including necessary clips, screws,

rubber beading, hinges/latches, and all accessories for proper fixing. The

61 frame shall be made of aluminium section 25×25×1.2 mm thick, SS mesh of 136.60 Sq.Mt. 378.75

0.35 mm wire dia with 1.4 mm × 1.4 mm opening, and detachable type for

cleaning and maintenance. Complete as per Engineer-in-Charge’s direction.

Providing and fixing standared extruded of alluminium section of size 63.50 x

38.10 x 1.95 mm,@ Wt 1.094Kg / Rmt with colour anodized alluminium frame

62 with 5 mm thick transparent bronze colour tinted float glass as details etc 4.50 Sq.Mt. 1525.00

complete for Fix window.

Providing and fixing standared extruded of alluminium section of size 63mm x

38.10mm x 1.2mm @ Wt. 0.643 Kg/mt with colour anodized alluminium

63 frame for ventilation with 5 mm thick frosted Louver glass as per details etc. 19.10 Sq.Mt. 1175.56

complete for Ventilation

Providing and fixing Safty grills of required pattern for Windows using 16 mm

dia M.S polished bars and Rectangular CRC pipes of size 50 * 30* 2mm at

64 Requuired spacing as per design and hold fasting with coach bolts including 4040.00 Kg. 115.14

one coat of primer and two coats of mattfinished oil painting etc complete.

Providing and laying 60x60 cm M.C.M.P Kotah stone { single piece not more

than 1.50 mt} of even grade 30 mm (Average) thick as per design incl. 7.5 cm

65 Skirting, laid on 20 mm thick (1:6) cement mortar, incl. Cutting , 2246.10 Sq.Mt. 1212.00

polishing, jointed with grey cement slurry & finishing etc. Complete as per

directed by engineer in Charge

Providing and laying coloured glazed tiles of the size 300 mm x 450 mm x

mm in dado on 10 mm. thick cement plaster 1:3 (1 cement : 3 coarse sand) &

66 jointed with white cement slurry, providing neccessary groove & filling with 325.10 Sq.Mt. 1488.24

epoxy adhesive etc. complete. Colour & Shade as approved.

Providing and laying matt/anti skid finished Ceramic tiles 6 mm thick

600x600 / 300x300 in flooring laid on a bed of 12mm thick cement mortar 1:3

67 (1-cement : 3-coarse sand ) finishing with flush pointing in white cement, 79.20 Sq.Mt. 992.15

providing neccessary groove & filling with epoxy adhesive etc. complete as

per directed by engineer in charge.

Providing and laying Granite Stone slab 25 mm ( Average ) thick incl. Full

molded round front edge laid on 15 mm thick cement mortar 1:3 (1- cvement

68 : 6 coarse sand ) jointed with grey cement Slurry including rubbing and 43.60 Sq.Mt. 3821.80

polishing etc. Complete

Providing and laying broken chine mosaic flooring for terrace using

mm to 20 mm broken pieces of glazed tiles to be laid over cement mortar

1:3 to plain or slope and to be tempered to bring mortar creme out upto

69 surface using white cement including rounding off junctions and extending 1039.00 Sq.Mt. 779.70

them upto 15 cm along the wall,clearing with water and oxalic acid etc. as

Providing and laying mirror polished Green Marble stone slab 18 mm ( Average

) thick incl. machine cut in traingular form at junction placements & laid on

70 10 mm thick Chemical Adhesive jointed with same including rubbing and 386.00 Sq.Mt. 1314.10

polishing etc. Complete

Providing 15 mm. Thick Mala plaster in two coats on fair side brick / concrete

wall for interior plastering consisting of 12 mm. Thick backing coat of cement

71 mortar 1:4 (1-Cement : 4-sand) and 3 mm. Thick finishing coat of C.M. 1:1 (1- 1865.00 Sq.Mt. 195.42

cement : 1-fine sand) etc. complete for Ground

Providing 15 mm. Thick Mala plaster in two coats on fair side brick / concrete

wall for interior plastering consisting of 12 mm. Thick backing coat of cement

72 mortar 1:4 (1-Cement : 4-sand) and 3 mm. Thick finishing coat of C.M. 1:1 (1- 2021.00 Sq.Mt. 217.31

cement : 1-fine sand) etc. complete for First floor.

Providing 15 mm. Thick Mala plaster in two coats on fair side brick / concrete

wall for interior plastering consisting of 12 mm. Thick backing coat of cement

73 mortar 1:4 (1-Cement : 4-sand) and 3 mm. Thick finishing coat of C.M. 1:1 (1- 912.00 Sq.Mt. 239.20

cement : 1-fine sand) etc. complete for Second floor.

Providing 15 mm. Thick Mala plaster in two coats on fair side brick / concrete

wall for interior plastering consisting of 12 mm. Thick backing coat of cement

74 mortar 1:4 (1-Cement : 4-sand) and 3 mm. Thick finishing coat of C.M. 1:1 (1- 103.00 Sq.Mt. 261.09

cement : 1-fine sand) etc. complete for third floor.

Providing 10 mm. Thick cement plaster in single coat for plastering on

ceiling and soffits of stairs upto floor two level and finished even and

75 smooth in : (I) Cement mortar 1:3 (1 cement : 3 sand) Ground Floor 904.10 Sq.Mt. 171.71

Providing 10 mm. Thick cement plaster in single coat for plastering on

ceiling and soffits of stairs upto floor two level and finished even and

76 smooth in : (I) Cement mortar 1:3 (1 cement : 3 sand) F.F 939.60 Sq.Mt. 193.60

Providing 10 mm. Thick cement plaster in single coat for plastering on

ceiling and soffits of stairs upto floor two level and finished even and

77 smooth in : (I) Cement mortar 1:3 (1 cement : 3 sand) S.F 365.80 Sq.Mt. 215.48

Providing 10 mm. Thick cement plaster in single coat for plastering on

ceiling and soffits of stairs upto floor two level and finished even and

78 smooth in : (I) Cement mortar 1:3 (1 cement : 3 sand) Fourth Floor 20.40 Sq.Mt. 237.37

Providing 20 mm thick cement plaster in single coat on brick / concrete wall

for interior plastering up to floor two level finished even and smooth (ii)

79 cement mortor 1:3 (1- cement, 3- sand) and mixing recorner - S 5 132.00 Sq.Mt. 301.16

waterproofing materials in cement mortor in proportion crecommended by

the manufacture for Ground Floor

Providing 20 mm thick cement plaster in single coat on brick / concrete wall

for interior plastering up to floor two level finished even and smooth (ii)

80 cement mortor 1:3 (1- cement, 3- sand) and mixing recorner - S 5 281.00 Sq.Mt. 329.92

waterproofing materials in cement mortor in proportion crecommended by

the manufacture for Parapet Walls (Internal Side)

Providng and applying two coats of Birla or Asian acrylic lappy (putty) and

two coats of primer & Wall painting ( two coats) with plastic emulsion paint

of approved brand and manufacture on wall surfaces to give an even brushing

the surface free from mortar droppings and other foreign including Wall

81 painting (two coats) with plastic emulsion paint of approved brand and 4901.00 Sq.Mt. 123.44

manufacture on undecorated wall surface to give an even shade including

throughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth.

Providng and applying two coats of Birla or Asian acrylic lappy (putty), One

coat of primer and two coats Wall painting ( Two coats) with plastic emulsion

paint of approved brand and manufacture on ceiling & sofit to give an even

brushing the surface free from mortar droppings and other foreign including

82 Wall painting (two coats) with plastic emulsion paint of approved brand and 2230.00 Sq.Mt. 128.97

manufacture on undecorated wall surface to give an even shade including

throughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth.

20mm Thick GUTAKA FINISHED cement plaster on walls up to 10mtr. above

ground level consisting of 12 mm Thick coat of c.m 1:3 ( 1 cement :3 sand)

83 and 8 mm. Thick finishing coat of c.m. 1:1 ( 1 cement : 1 sand) including 1806.80 Sq.Mt. 356.35

making groove 1cm wide and 8 mm deep as approved pattern etc. complete

20mm Thick GUTAKA FINISHED cement plaster on walls height above 10mtr.

consisting of 12 mm Thick coat of c.m 1:3 ( 1 cement :3 sand) and 8 mm.

84 Thick finishing coat of c.m. 1:1 ( 1 cement : 1 sand) including making groove 112.04 Sq.Mt. 399.27

1cm wide and 8 mm deep as approved pattern etc. complete as directed.

Finishing wall with wall primer of approved brand (One Coat) & weather proof

exterior emulsion paint on wall surface (Two coats) to give an required shape

85 even shade after thoroughly brushing the surface to remove all dirt, 2199.90 Sq.Mt. 136.78

and remains of loose powdered materials etc complete

Providing and fixing Stainless steel railing made from anticorrocive 304 grade

S S hand rail hollow pipe of 50 mm dia (16Gauge), Baluster of 25x25 mm SS

86 Hollow Box pipe for supoorts at 1.2 mt Vertical supports at equal distance 43.90 Rmt. 2008.89

fixed in RCC/Brick, Railing including accessories as per detailed drawing as

Providing and fixing mild steel railing 600 mm high over 150 mm thick parapet

wall, including fabrication from MS sections (main frame Ver.&Hoz. 40mm

pipe hollow / Hoz. Support 25mm hollow pipe), welding, grinding smooth,

87 fixing with base plates, Anchor Bolts, one coat red oxide primer and two 203.60 Rmt. 1438.24

coats synthetic enamel paint, complete as directed by Engineer-in-Charge.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe (

SCH- 40) for cold water including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp at every two metre C/C

88 or shall be concealed as directed including necessary fittings etc. including 210.00 Rmt. 72.65

testing of pipe and joints and fixing the same with adhesive solvent, including

cost of all materials.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR

13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water

89 of following dia. nominal bore tube fittings and clamps including making good 102.00 Rmt. 208.80

the wall, ceiling and floor etc. complete. [B] 20 mm.

Providing laying and jointing in true line and level following dia. U.P.V.C.

Pipe (SCH -40) line including fittings, fabricated from G.I. angle section of

size 40 mm × 40 mm × 5 mm, cut, welded, and fixed in position with anchor

90 fasteners or expansion bolts to wall, including providing necessary clamps, 240.00 Rmt. 91.84

nuts, bolts, washers, complete. make or equivalent as approved by Engineer

In charge. Pipe shall be fixed on 25 mm

Providing laying and jointing in true line and level following dia. U.P.V.C.

Pipe (SCH -40) line including fittings, fabricated from G.I. angle section of

size 40 mm × 40 mm × 5 mm, cut, welded, and fixed in position with anchor

91 fasteners or expansion bolts to wall, including providing necessary clamps, 388.00 Rmt. 148.12

nuts, bolts, washers, complete. make or equivalent as approved by Engineer

In charge. Pipe shall be fixed on 40 mm

Providing laying and jointing in true line and level following dia. U.P.V.C.

Pipe (SCH -40) line including fittings, fabricated from G.I. angle section of

size 40 mm × 40 mm × 5 mm, cut, welded, and fixed in position with anchor

92 fasteners or expansion bolts to wall, including providing necessary clamps, 50.00 Rmt. 195.67

nuts, bolts, washers, complete. make or equivalent as approved by Engineer

In charge. Pipe shall be fixed on 50 mm

Providing and fixing Heavy Handle valve of aprroved brand & follwing

93 internal dia of Brass including fixing in pipe lines etc.complete (C) 25 mm 15.00 Nos. 527.32

Providing and fixing Heavy Handle valve of aprroved brand & follwing

94 internal dia of Brass including fixing in pipe lines etc.complete (E) 40 mm 10.00 Nos. 771.24

Providing and fixing Butterfly valves IS 13095 with ISI mark PN 1.6 of aprroved

95 brand & follwing internal dia including fixing in pipe lines etc.complete (A) 5.00 Nos. 3587.87

Providing and laying in trenches galvanised mild steel tubes (Medium grade)

96 of the following nominal bore, and tube fitting (Earthwork in trenches to be 120.00 Rmt. 426.40

measured and paid for separately)(D) 40mm

Providing and fixing in trenches 10.0 Kg. F/Cm2 working pressure polythene

pipes of the following outside Dia. Low densidy, complete with special falnge

97 compression type fittings. including making good the earth.(F) 75mm 100.00 Rmt. 280.23

Providing laying and jointing in true line and level 110 diameter

U.P.V.C. SWR Type B pipe confirming to IS 13592-1992 with one end plain

and other end socketed with rubbering, & fitting, G.I. angle wall-mounted

support for PVC line fixture, fabricated from G.I. angle section of size 40 mm

98 × 40 mm × 5 mm, cut, welded, and fixed in position with anchor fasteners or 496.00 Rmt. 876.90

expansion bolts to wall, including providing necessary clamps,

nuts, bolts, washers, complete as per manufacturer’s specification and

direction of the Engineer-in-Charge.

Providing and fixing PVC SWR Nahni Trap IS 14735 for drain - 100 mm

99 diameter with jali of the following nominal diameter of self cleansing design 60.00 Nos. 586.27

with C.I. screwed down or hinged grating

Providing and fixing Screw down Quarter turn bib taps of following size

(A) Brass chromium plated screw down Bib tap (I) 15 mm dia {Plumber,

100 Mark, Esco equivalent brand} 64.00 Nos. 186.83

Providing and fixing CP brass Quarter turn pillar tap, capstan head

screw down high pressure with screw, shanks and back ndts (A) 15 mm dia

101 {Jaquar< Plumber, Mark Long pipe} 4.00 Nos. 308.73

Providing and fixing chromium plated brass half trun flush cock of approved

quality including fixing in pipe line etc. complete.(i) 20mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(E)

Providing and fixing wash basin of HINDWARE MAKE MODEL No. Magna Cat.

No.: 10079 (Regd. Design No. 208785) Size (LxW): 63 x 50 cms, CP brass

bottle trap with brass union and CP breass wall discharge pipe with fianges

and cap of jaquare / Cabtree / plumber , 32mm dia Gi waste pipe with

fittings up to floor trep, 32mm dia CP brass waste coupline with CP chain and

rubber plug,15 mm dia CP brass conseaied stop valve of jaquare / Cabtree /

104 plumber 15mm heavily quality fiexible PVC inlet connecton of required length 6.00 Nos. 5440.87

with bress union, washer and CP brass cap complete in all respects with

15mm dia CP brass piller tap of jaquare / Cabtree / plumber cutting and

making good the walls brick / RCC work as directed and making good the

same etc. complete.

Providing and fixing pearl-shape vitreous china wash basin (including

overflow/waste outlet hole) of approved make and quality, mounted on

mm thick machine-polished granite platform of size 2′ × 2′ (approx. 0.40 m²),

including edge polishing, cutting and making openings for fittings. The item

shall include supply and fixing of all required C.P. brass waste coupling (32

105 mm dia), bottle trap, pillar tap, M.I. Fisher union, P.V.C./C.P. flexible 28.00 Nos. 6194.33

connection pipes, G.I. clamps, silicone sealant, epoxy adhesive, and other

small consumables, complete with necessary plumber and mason labour for

fixing, jointing, testing, and finishing the work in all respects as directed by

the Engineer-in-Charge.

Providing and fixing SS Sink Glosy ASIS 304 Grade × 100 thick with over all size

610 × 460 mm & bowl Size 560 × 410 × 200 with single hole for pillar tap

106 Fixing in sanwhich platform including cutting holes and making goods the 3.00 Nos. 3419.10

same including . necessary Fixture, connections and waste Pipes

Providing and fixing wash down water closet (Europen type W.C.Pan) with

integral"P" and "S" trap including jointing the trap with soil pipe in cement

mortar 1:1 (1-cement, 1- sand) of Hindware Wall Hung Water Closet

has a slow falling seat cover with an antibacterial and germ free ceramic

surface. with a water saving dual flush. and including jet spray

operated with necessary valve of Jaquar / Cabtree / Plumber including

cutting holes in walls and making good the same connecting the flush bend

with cistern and closet vitreous china etc. complete.

Providing and fixing water closet squatting Pan (Indian type W.C. Pan) size

108 580mm (Earthwork, bed concrete, foot reste and trap Including. (I) Long 17.00 Nos. 1174.63

pattern = White colour

Providing and fixing Urinal or approved quality including conecting the Urinal

109 with waste pipe , tap etc. complete.(A) White earthenware flat back or 15.00 Nos. 1074.86

corner type size 430mm x 260mm x 350mm.

Providing, fixing, and testing of Disabled Friendly Toilet Set (CERA CRUSE Set

or equivalent approved make) comprising of the following components –

European Water Closet (EWC) of size 710 × 370 × 810 mm (S or P Trap) with

matching cistern, soft close seat cover, twin flush fittings, wash basin of size

510 × 400 mm with spatula lever basin mixer, bottle trap, toilet paper holder,

wall-mounted grab bars (600 mm long – two numbers), wall-mounted hinged

support rail (750 × 750 mm – one number), all in stainless steel 304 grade,

110 along with all necessary CP fittings, connections, fixing materials, nuts, bolts, 1.00 Nos. 27094.26

washers, and gaskets, etc. The fixtures and rails shall be in contrast color

with floor and wall tiles, fixed firmly in position with suitable supports as per

manufacturer’s specifications and as directed by the Engineer-in-Charge. All

fittings shall be tested for proper functioning, alignment, and leakproof

performance, including making good the wall and floor surfaces

after installation.

Providing erecting and fixing Anti Bacterial,Virgin plastic, 100 % UV Stabilized

Rust Proof, Algae protected, strong - 8 layer PVC ISI Mark Water tank With

111 Required Capacity including with overhead tank fillter and all necessary 24000.00 Liter 3.95

fittings & connection etc. complete on terrace.

Providing and fixing 600 mm x 450 mm bevelled edge mirror of superior

glass mounted on 6 mm thick A.C sheet or plywood sheet or PVC framing and

112 fixed to wooden plugs with C.P brass screw abd washers. 20.00 Nos. 859.41

Providing and fixing CP brass stop cock of approved quality 15 mm size

113 with adjestable wall flange 58.00 Nos. 205.83

Providing and fixing S.W. Gully trap with C.I. Grating brick masonary chamber

and water tight C.I. Cover with frame of 300 mm. X 300 size (inside) with

114 standard weight 10.00 Nos. 1292.19

(I) Square mouth traps (C) 150 mm. X 100 mm size p or R type

Constructing brick masonary chamber for under ground C.I. Inspection

chamber and bends with bricks having crushing strength not less than

Kg/cm2 in cm. 1:5 C.I. Cover with frame (light duty) 455 mm. X 610 mm.

Internal dimensions, total weight of cover with frame to be not less than

Kgs. weight of cover 23 Kg. and wt. of frame 15 Kg) R.C.C. top slab with

1:2:4 mix(1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm.

115 size ) foundation concrete 1:5:10 inside plaster 15 mm. thick with cement 10.00 Nos. 2932.93

mortar 1:3 finished smooth with a floating coat of neat cement on walls &

bed concrete etc. complete.

(I) inside dimensions, 455 mm. x 610 mm. And 450 mm. Deep for single

Providing and filling screened of burnt coal cinder including and consolidation

116 etc complete. 23.00 Cu.M. 999.90

Providing throating or plaster drip and moulding to R.C.C. Chhajja.

Providing and fixing “Sandwich Platform” type kitchen platform with bottom

support slab and top slab, made of 18–20 mm thick machine-cut, machine-

polished Granite stone slabs of approved shade and colour, including vertical

fascia, edge moulding, cutting for sink/hob, making necessary openings, and

providing nosing wherever required, fixed in position with cement mortar 1:4

and approved stone adhesive (epoxy/resin based), complete in all respects.

Providing and fixing C.I. Manhole cover 0.60m x 0.45m size having weight not

119 less than 35 kgs. 3.00 No. 958.17

SIGNAGES ON Door

Providing, Fabricating & Fixing 304 grade Stainless steel 1.5 mm thick

brushed steel finish plate fixed on a door using s.s studs and with

120 punched(laser cut) lettering carried out on s.s plate of required size and 200.00 Sq.inch 9.09

text as directed by Engineer etc.complete.

Providing & fixing Stainless Steel letters of approved design, 75–300 mm

121 height, 10 mm thick, polished finish, fixed with SS pins & epoxy adhesive on 12400.00 Sq.inch 11.11

Brick/RCC wall, complete in all respects.

Providing and fixing chiken mesh jali with square of 12.50 x 12.50 mm of

122 gauge at junction the Brick.masonary and reinforcement cement concrete 1080.50 Sq.Mt. 194.12

member including fixing materials scaffolding labour etc.

Providing and fixing M.S. Square pipe 50mm x 50mm x 1.6 mm thickness

weight 2.38 Kg / Rmt suggested by Engineer In Charge including cutting,

123 bending welding, jointing and fixing on site including painting two coats etc. 72.00 Rmt. 170.34

Providing and fixing roll-formed GI louvres made from 114 mm wide, 0.55 mm

thick GI coil (weight not less than 490 gm/mtr), roll formed to produce

mm effective louvre width, snap-fixed on specially shaped GI

channels/frames. Louvers and channels shall be degreased, passivated and

powder coated to 55 micron (approved shade) after pretreatment, and

124 completed with necessary cleats, fasteners, neoprene washers/EPDM gaskets, 72.00 Sq.Mt. 1596.23

drip profile, and sealing. Work includes supply of GI sheet & channels, roll

forming, shop fabrication, powder coating (55 µm), site fixing with dash/bolt

fasteners, trimming, alignment, testing and cleaning, complete as per

drawings and Engineer-in-Charge.

Providing and laying tactile (warning and guiding) floor tiles conforming to IS

13801 : 2021 and IS 15658 : 2021, made of factory-pressed vitrified material

of approved colour and pattern (yellow or contrast shade), 300 × 300 × 10 mm

thick (typical), laid in required line and level over 20 mm thick 1:4 cement

125 mortar bed, including grouting joints with white cement and matching 23.00 Sq.Mt. 1599.84

pigments, finishing, curing, and cleaning complete, as per NBC 2016 – Section

11 (Barrier-Free Access) and CPWD Handbook on Barrier-Free Built

Environment (2014).

Providing and fixing aluminium corner edge protection (make, KosmoCare

Wall Corner Guard 90° or Equivalent) suitable for disabled persons, of size

cm × 5 cm × 150 cm height, weighing approximately 1 kg per piece, Per

126 fabricated from approved quality aluminium section, fixed to wall corners 94.00 2000.81

with stainless steel screws, including all fittings, drilling, alignment, and

making good the surface, complete as directed by Engineer-in-Charge

Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand : 8-

127 hand broken stone aggregates 40 mm nominal size) and curing complete (A) 10.00 Cum 2769.69

Foundation and Plinth

Providing and laying controlled cement concrete M.200 and curing complete

128 including the cost of formwork and reinforcement for reinforced concrete 103.00 Cum 6013.71

work in (C) Ground BEAMS

20mm thick sand faced cement plaster on walls upto height 10 metres above

ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-

129 sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. 984.00 Sqmt. 342.41

Finishing wall with weather proof exterior emulsion paint on wall surface

(two coats) to give an required shape even shade after thoroughly brushing

130 the surface to remove all dirt, and remains of loose powdered materials.etc 984.00 Sqmt. 120.26

fabricating and fixing double leaf M.S. main gate, as per drawing, including

131 supply, Erection, fabrication, fixing, hardware, primer + paint, transport, 8.10 Sqmt. 5646.90

testing and commissioning.

Providing and fixing 1.20 Metre high fencing with 2.0 Metre long M.S. Angle

posts 40mm x 40 mm x6 mm and oil painting 3 coats fixed at 2.5 Mt,C/c. with

five Horizontan lines and two diagonals of galvanised steel barbed wire

132 weighting 9.38 Kg. per 100 Metre, strained and fixed to posts with G.I,staples 285.00 Rmt. 391.93

including fixing the postsin ground with 0.5 M x 0.5.M x 0.5 M. block in

C.C1:5:10 etc complete.

Providing laying and jointing in true line and level 160 diameter

133 U.P.V.C. SWR Type B pipe confirming to IS 13592-1992 with one end plain 200.00 Rmt 834.38

and other end socketed with rubbering, & fitting 150mm

Providing and construction of junction chamber of size 0.35 x 0.35 x 0.60 mt.

134 including connecting of rain water pipe as per detailed drawing and as 10.00 Nos. 1157.46

directed by Engineer in charge {RA}

Providing and construction filter chamber of size 2.06 x 1.21 x 1.20 mt. as

135 including connecting of rain water pipe as per detailed as directed by 2.00 Nos. 12178.58

Engineer in charge including cost of labour and material

Providing water harvesting pit of 2.00 x 2.00 x 4.00 mt. size for water logging

with excavation in any strata upto four meter depth. Filling the pit with B.T.

metal 40 mm in 0.60 mt. depth with 25-40 mm kapachi , 0.30 mt. depth and

2.0 mt. depth with coarse sand in layers including making P.V.C. line for

water inlet etc. as directed with 250 mm dia bore 35 mt. depth and 150 mm

dia P.V.C. pipe of 10 kg. f/cm2 casing with gravel packing or as directed Rate

Earthwork for embankment including breaking clods, dressing with all lead

137 and lift (including watering and consolidation)(A) From Borrow pits within 175.00 Cum 132.37

Providing, laying, spreading and compacting stone aggregates of 63 to 45mm

sizes & Stone screenings Type-A for WBM Grade-II, as per specification

including spreading in uniform thickness, hand packing, rolling with smooth

wheel roller 80-100 kN in stages to proper grade and camber, applying and

138 brooming, stone screening/binding materials to fill-up the interstices of 233.00 Cum 1116.44

coarse aggregate, watering and compacting to the required density grading

as per Technical Specification Clause 405. By Manual Means

Providing and cast in situ Vacuum De-watered Unreinforced cement concrete

of grade M-20-Trimix flooring for average wearing coat / C.C. pavement laid

as directed in approved fixed side form work of steel channel including

vibrating by screedneedle vibrator and leveling with trimix, surface vibrator,

Vacuum De-watering with trimix vacuum pump, floating and further

compaction with trimix skin floater equipped with floating disc, and finished

139 in continous operation including cutting the concrete with concrete cutting 165.00 Cum 6877.46

machine for contraction joints at every 4.00 mtr and expansion joint at

interval of 40 mtr of size 6x12mm to 12x25mm deep or as specified /

providing stripped / broom finish evenly, applying debonding strips, bitumen

primer,bituminous sealant,12 mm dia jute rope and curing etc. complete.

Providing and fixing pre-cast concrete kerb stone of gray cement based

concrete block 30cm length,30cm height and 15cm thick of M250 grade

140 concret as per approved design and including excavation for fixing in proper 370.00 Rmt 374.92

line and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc

Providing and fixing pre-cast Rubber Dye / Steel dye inter locking concrete

block 60mm thick with grade of concrete M30 pnumatic compressed/ vibrated

mechanically and as per approved design Confirming to IS 15658:2006

141 including 35mm Sand layer for levelling and filling the joint with sand in 156.00 Sqmt 706.93

proper line and level as per Guideline of IRC :SP 63-2018 etc complete.

Providing panel wall for dry stone pitching in uncourased rubble masonary

142 with had stone of approved quality in cement. mortar 1.5 including curing 20.00 Cum 2650.76

Supplying, installation, testing and commissioning of ABC type (Multipurpose)

fire extinguisher, 5 kg capacity, filled with dry chemical powder conforming

to IS: 15683, complete with squeeze grip release mechanism, pressure gauge,

143 wall-mounting bracket and all accessories, including painting, lettering, and 33.00 Nos. 3535.00

marking as per IS standards, complete as required and as directed by the

Engineer-in-Charge.

Supplying, installation, testing and commissioning of Carbon Dioxide (CO₂)

type fire extinguisher, 4.5 kg capacity, complete with ISI mark, discharge

nozzle, squeeze grip release mechanism, pressure gauge (where applicable),

144 wall-mounting bracket and all accessories, conforming to IS: 15683, including 5.00 Nos. 5201.50

painting, lettering and marking as per IS standards, complete as required and

as directed by the Engineer-in-Charge.

Earthwork for embankment including breaking clods, dressing with all lead

and lift and including watering rolling and consolidation of subgrade in layers

145 at O.M.C. to required dry density including filling the depression which occur 4819.10 Cum 163.51

during the process using power roller 8T to 10T.(B) From Borrow area within

Earthwork in cuting in all sorts of soil and soft murrum including conveying

and spreading the stuff, embankment as and where directed within

146 200meters from the end of the cutting with all required lead and lift.(C) 641.27 Cum 134.13

Above 400 Meters upto 500 Meters.

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length , in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden box, single mounting base

147 frame covered with textured/metallic/white front plate modules erected on 379.00 Pt 485.81

/ in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling

rose / H.D.Connector as directed. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete CAT-III

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green)

both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multi strand copper

wires up to 10 mtr length, in below type of pipe erected with 6A Modular

type switch and hum free EME step type electronic fan regulator mounted

and accessories with earth continuity of following type erected on PVC /

148 Metallic/Wooden box, single mounting base frame covered with 179.00 Pt. 674.68

textured/metallic/white front plate modules erected on / in wall / ceiling as

per pipe erected. with necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete CAT-III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both

are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected complete with Modular

type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall / ceiling as per pipe

erected with following type of accessories. [I] For 6A Plug and 6 a switch

with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db board (f) with

medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete cat-III

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin

socket erected on PVC / Metallic/Wooden box, single mounting base frame

150 covered with textured / metallic/white front plate modules erected on / in 292.00 Pt. 257.55

wall / ceiling with following type accessories Cat.III

Providing following type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame covered with textured /

151A metallic/white front plate , modules erected with necessary connections as 40.00 Ea. 25.25

per site situation directed by Engineer In charge. (7) Blank Plate Single cat-III

151B (8) Computer RJ-45 socket CAT-III 45.00 Ea. 160.59

151C (9) 16 Amp. SP one way switch Cat.III 48.00 Ea. 180.79

151D (10) 6/16Amp. Universal socket Cat.III 48.00 Ea. 199.98

151E (15) 32 Amps. DP switch with Indicator cat-III 3.00 Ea. 280.78

(21) Foot Light as per colour requirement with concealed box, modular

accessories, acrylic glass cover with suitable LED watt with all accessories as

151F per following module (b) Four modules 17.00 Ea. 494.90

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following

size complete to be erected on/in wall or ceiling erected with necessary PVC

152A fittings & Junction boxes fixed with adhesive solution & Clamps with following 250.00 Mtr 24.24

dia of pipes, in approved manner as directed (A) 20mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be erected

concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor

153 FRLS PVC insulated stranded wire of green colour for earth continuity of 2440.00 Mtr 82.82

following size (a) with medium class Rigid PVC pipe and accessories (b)

wire 2.5 sq. mm

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be erected in /

on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated

154A stranded wire of green colour for earth continuity of following size (a) with 320.00 Mtr 112.11

medium class Rigid PVC pipe and accessories (a) 2 wire 4 sq. mm

(i) 4 wire 10 sq. mm

(use earth wire of 4 sq.mm )

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi

stranded, annealed copper conductor with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in existing pipe of following size

155A (Specifically for control panel, relays, power switchgears, motor starters & 25.00 Mtr. 56.56

control wiring) with required size of copper lugs, nuts and bolts if

required.(e) One wire 6.00 sq. mm

155B (f) One wire 10.00 sq. mm 35.00 Mtr. 91.91

155C (i) One wire 35.00 sq. mm 25.00 Mtr. 300.98

155D (k) One wire 70.00 sq. mm 15.00 Mtr. 669.63

Supplying and erecting Flexible PVC insulated multistrand multicore 1.1 kv

156 grade ISI marked copper wires of following size to be erected as directed. e) 160.00 Mtr. 46.46

1.50 Sq.mm 3 core round PVC sheathed

Supplying & erecting approved make LAN cable of following size in existing

pipe as per direction [C] CAT -

Providing & erecting Switch board for Computer or electric apparatus

consisting of following modular type accessories mounted with PVC /

Metallic concealed/open box with single mounting base frame covered with

textured/metallic /white front plate,modules erected with necessary

158 connections as directed 45.00 Ea. 1133.22

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories Cat. III

159 Decorative call bell Ting-tong box type 250 volts complete erected 3.00 Ea. 71.71

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to

0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall

be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with diffuser with

company mark/name 160V to 270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

160 LED driver efficiency > 85 % 60.00 Ea. 165.64

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.) (A) Tube Light with

integral driver (i) 5-10 Watts, Surge-2 KV, IP-20, conventional 1 to 2 feet, Cat-

161A (v) 36-40 Watts, Surge-2 KV, IP-20, conventional 4 feet, Cat-lll 274.00 Ea. 535.30

Supplying and erecting LED street light / Flood light fittings with High power

White LEDs wattage of 3 Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio

162 >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( 19.00 Ea. 5976.17

fittings required LM-79 & LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.) (A) Street Light (IP-

65), Surge protection -4KV integral and ,Light must have 440VAC line supply

with over-voltage protection. (iii) Above 60 to 90 watts Cat-lll

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must have

163A 440VAC line supply with over-voltage protection. (vi) above 160 to 200 watts 14.00 Ea. 9647.52

(C) Post Top Lantern LED fitting comprises of finish cast aluminum spigot and

spun aluminum canopy fixed with opal polycarbonate, pipe arrangement for

163B vertical mounting driver and accessories wired upto terminal block.IP 65(i)20- 2.00 Ea. 4092.52

Providing and erecting Approved make Four pole moulded case circuit breaker

having breaking capacity ICU of 25 KA. at 415 V,having normal current rating

up to 25 A to 100A. with Fixed thermal & magnetic release suitable to work

164 on A.C. supply 50 c/s. with all internal connections, spreader tinned copper & 2.00 Ea. 6173.12

complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only

Providing and erecting Approved make Four pole moulded case circuit breaker

having breaking capacity ICU of 35 KA. at 415 V. having normal current rating

125A. with Fixed thermal & magnetic release suitable to work on A.C.supply

165 50 c/s. with all internal connections, spreader tinned copper & complete 7.00 Ea. 8055.76

erected in existing 16 G.M.S. housing. ICS=100% of ICU only

Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 35 KA. at 415 V. having Normal

current rating 200A.with variable Thermal & magnetic release suitable to

166 work on A.C.supply 50 c/s. with all internal connections, spreader tinned 3.00 Ea. 16221.61

copper & complete erected in existing 16 G.M.S.housing ICS=100% of ICU

Providing and erecting Approved make Four pole moulded case circuit breaker

having breaking capacity ICU of 35 KA. and above at 415 V . having normal

current rating 250A. with variable thermal & magnetic release suitable to

167 work on A.C.supply 50 c/s. with all internal connections, spreader tinned 1.00 Ea. 20946.39

copper & complete erected in existing 16 G.M.S. housing. ICS=100% of ICU

Providing and erecting Approved make Earth fault Relay suitable to mount

with inter connection suitable to following size of moulded case circuit

168 breaker having CT ratio & MCCB rating as following along with shunt trip 4.00 Ea. 4983.34

220V AC. with all internal connections & complete erected in existing

M.S.housing.. (2) 125 A -200 A , CT Ratio 1/200

Supplying & erecting approved make Four Pole 415V change over switch

169 interior for panel mounting with operating mechanism A.C.23 duty confirming 1.00 Ea. 2611.86

to IS for (A)32-40A Cat-lll

Supplying and erecting triple pole & neutral 440V / 500V panel mounting

Copper Busbars with four equal Nos. of electrolyte bus having current density

not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of following current

170 carrying capacity, erected with necessary bus bar supports /insulators, main 1.60 Rn mtr. 1961.42

cable socket to each bar, erected in existing cubical panel with necessary

connections. (A) Suitable for 100 Amp. Capacity

170A (B) Suitable for 200 Amp. capacity 3.00 Rn mtr. 3202.71

Supplying KITKAT pattern porcelain cut-out fuse with base of following

current capacity erected on existing block board.(vi) 200 A. 500 V.

providing and erecting Miniature circuit breaker single pole 0.5A to 2A system

172 and having breaking capacity 10 KA to be erected in existing box. confirming 33.00 Ea. 270.68

to IS 8828/1996 with ISI Mark Cat.III

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable

to operate on 240 V A.C. system and having breaking capacity 10 KA to be

173 erected in existing box. confirming to IS 8828/1996 with ISI Mark Cat.III 186.00 Ea. 112.11

Providing & erecting 240 V MCB double pole switch for lighting Load (B Curve)

174 having 10 KA breaking capacity & confirms to IS : 8828 in existing box having 10.00 Ea. 295.93

following capacity (B) 40 Amp. Cat-III

Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve)

175 having 10KA breaking capacity & confirms to IS :8828 in existing box having 23.00 Ea. 638.32

following capacity (b)40 Amp. Cat-III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C

176 Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box 21.00 Ea. 737.30

having following capacity (c)63 Amp. CAT-III

Providing and erecting Sheet Steel powder coated MCB distribution board -

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of same company of MCB to

be used) suitable for (B) three phase incoming and single phase horizontal

type outgoing Per phase isolation type (PPI) (b) sheet steel double door (ii)6

providing and erecting Approved make RCCBs conforming to IS: 12640 and

having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz. having characteristic of

178 quick action & tripping with all advance feature & do not incorporate any 36.00 Ea. 2235.13

electronic component. for following Max. rating erected as directed (ii)

Amps.DP Cat-III

179 Providing and erecting Annealed bare Copper wire 8 to 16 S.W.G. 6.00 Kg. 794.87

Supplying & erecting earth pit of minimum bore dia.150mm size approved

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of

50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-

250 Micron galvanising, connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with high charge dissipation

suitable for following type of applications with chamber and heavy duty

cover. (A)(approved make OEM has to submit test certificate including value

of earth resistance of installation duly stamped and signed by agency and

officer Incharge has to ensure the value of earthing resistane mentioned in

test Certificate) & having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back

fill Compound :- Earthing compound should be capable to retain moisture for

long time Necessary test report must be submitted by Agency. (a) For

Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing & erecting weather proof, dust & vermin proof, floor mounted front

operated indoor type cubical panel board necessary IP-42 and above

protection as per approval from engineer incharge made from 14 SWG thick

CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for

internal partitions with necessary accesories , supporting angles/ flats

channel including cutting, bending, drilling, welding, riveting with internal

partitions & cable alley as per requirements & instruction of engineer-in-

charge with erection of supplied switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copper-aluminium strips, rubber grommets, rib,

bakelite control fuses/MCB for measuring instruments, earth bus & earth

181 bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged doors, 6.00 Sq mtr 10468.65

handles with locking arrangement and rubber gasket,heavy duty end terminal

connection,danger notice board,necessary ventilation,earthing strip

complete. The Panel shall be painted with epoxy powder coating. (The rates

excludes the cost of switchgears, bus bars, inter connecting mains & Copper

Aluminium strips, meters, Fuses etc. The dimension shall be measured

excluding base beams) The panel shall be supplied with following approved

manufacturers with following size. (A) locally fabricated panel board (i) with

Providing , erecting , fabricating the M.S. structure as per requirement on site

incorporating proper size of M.S. angles,square,round, flats, bars, channels,

sections complete with cutting, welding, grinding & finishing duly painted

182 with one coat of red oxide with erection on site as per direction of engineer 60.00 Kg. 77.77

in charge with necessary grouting, cementing, plastering & finishing complete.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or

183 in existing trench / pipe of following size of cables (D) 3 1/2 core 70 Sq. 24.00 Mtr. 378.75

mm ( 35 Sq. mm 1/2 core)

183A (E) 3 1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core) 70.00 Mtr. 490.86

183B (F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core) 30.00 Mtr. 540.35

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand /

Solid Aluminium conductor for 1.1 KV. to be laid on wall with necessary

184 clamps or in existing trench / pipe of following size of cables, (C) 4 core 10 450.00 Mtr 140.39

Making trench in soft soil of suitable width of 90 cm deep for laying cable or

185 locating the fault all over the run and back filling the same and making the 260.00 Mtr 55.55

surface as normal ground.

Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm. below

186 ground across the road crossing or on floor with necessary material in an 10.00 Mtr 263.61

approved manner and making the ground as per original.(E)150 mm dia

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting

187 accessories of same material at required depth in existing trench for laying 210.00 Mtr. 62.62

of cable. below ground / road surface for enclosing cable (A)50 mm outer

187A (B)63mm outer dia 60.00 Mtr. 73.73

Providing and, fixing heavy duty flange type brass double compression type

cable gland with rubber ring for PVC insulated armoured cable complete with

188 out going tails, insulating tape etc for following size of cables. (C) 3 & 1/2 4.00 Ea. 103.02

Solder less crimping type Aluminium lugs conforming to IS suitable for cable

of following size evenly crimped with high pressure tool & connected to

189 switchgear terminals with brass/cadmium plated nut bolts in an approved 16.00 Ea. 25.25

manner. (E) 70 Sq.mm.

Supply, Installation, Testing and Commissioning of suitable sweep, BEE 5 Star

rated, Ceiling fan with Brush Less Direct Current (BLDC) permanent ferrite

magnet Motor, class of insulation: B, Rust free 3 nos.Aluminium blades, 2 nos.

canopies, shackle kit with earthing provision, copper winding, Power factor

not < 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum

CMM, 350 RPM,230v (tolerance as per IS : 374-2019), THD < 10%, compitible

with electronic regulator unit for Speed Control and all remaining accessories

190 including safety pin, nut bolts, washers, temperature rise = 75 degree C 179.00 Ea. 2629.03

(Max.), suitable for 140 to 285 Voltage and rectifier circuit with surge, over

current and overload protection , 50 Hz, Single phase AC Supply, earthing

etc. Complete as required.[ Make shall be approved by Engineer in Charge]

(A) 1200 mm Sweep (48")

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe

191 down rod erected duly painted for fan complete with proper insulation 110.00 Mtr. 108.07

without leakage and earthing.

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the

RCC bars up to 50mm length each side and pierced through a 16 Gauge M.S.

192 box / Heavy Duty PVC box complete erected concealed in Ceiling with 179.00 Nos 108.07

necessary finishing.

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan

Providing & erecting fresh air fan 250 mm dia with square frame make of ABS

body with louvers CAT-II

Supplying and erecting approved make Octagonal pole made from HR sheet

steel. The pole should be made as per IS. and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable suspend local wind speed with

integral Junction box consist of terminal plate of min 6mm Hylam sheet,

standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal

and arrangement for cable termination to be erected With Suitable

195 foundation (Included) as per details given by manufacturer considering site 11.00 Ea. 8192.11

requirement. (D) 6 Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm

thickness with 200mmX200mmX12mm base plate, 4-M20 Bolts and 600mm

long with necessary G.I. J Bolts .Approx Pole weight 59 kg

Supplying & erecting approved make SMC press moulded composite FRP.

loop-in, loop-out approx. 2mm thick box complete with Bakelite connector

strip 5way(3P+N+E),DIN rail for mounting mob & hinged doors as per

196 requirement having locking arrangements with mounting clamp with nuts, 14.00 Ea. 476.72

bolts & washers suitable for erection on pole with cable clamps& earth bolt

of following size of box. (C)150mm x 125mm x 100mm [deep]

Providing and erecting street light pole bracket comprising main B Class MS

pipe of 4.2 cm/require outside dia. complete with suitable B Class M.S.

sleeve tubing of approx. 45cms.length and suitable for 76.5 mm / 80mm. /

require size pole top having sufficient fasteners for fixing the brackets and

having spread of 1 mtr. length with suitable rise as per site condition &

suitable welded stiffener reducer and nipple with check nut complete painted

with one coat of Red oxide / PU base primer and two coats of Aluminium / PU

paint. paint with following nos of arms. [B] Double Arm Bracket 1 Mtr

197A [A] Single Arm bracket 1 Mtr 5.00 Ea. 561.56

Supplying and erecting B class Galvanized iron pipe having smooth finished

bore of the pipe on both ends erected nuts and bolts along the pole / wall

198 shaping the pipe as per site requirement. Pipe dia as following.(A) 25 mm dia 14.00 Mtr 180.79

Supplying & erecting approved make IP 55 grade Company fabricated Timer

Panel of following capacity for switch On-Off street lights on time scheduling

basis made from 16G CRCA sheet duly epoxy power painted inside and outside

with hinged doors and locking arrangement consisting of suitable size of

199 Pole MCB and 4 pole contactor (cat-III)with analog time switch, auto manual 2.00 Ea. 13350.18

switch of same make and suitable input and output Bakelite terminals and

with door earthing approved by Engineer in charge. (B) 40 Amp

Providing & erecting water cooler having storage capacity 150 Ltr. & cooling

capacity 150 Ltr.per hour @ an ambient temp of 45˚ C. The outlet temp. of

the water should drop by 15˚C within a hour, The water cooler should be

comprising of hermetically sealed compressor, fan motor, condensing unit,

water tank surrounded by evaporating, coil, thermostats, relay etc.complete

with necessary inlet & outlet connection. The body of water cooler will be

made from Stainless Steel.

Supplying & erecting reverse osmosis (RO) water purification system with

M.S. powder coated pedestal frame, prefilter housing carbon filter suitable

buster DC pump, auto low & high pressure switches with following size of LPH

capacity & erected as directed [D] 100 LPH with 1 phase / 3 phase Raw water

pump of 500LPH @ 2.5kg/cm2 - (1N0 - Kirloskar /CRI/Lubi), Dual media filter

201 10"x54" - (1 No), Micron cartridge filter 20" x 2.5" ( 1No), High pressure pump 3.00 Ea. 77891.20

500LPH @ 10kg/cm2 - (1No - Shimge /CRI /Lubi), RO Membrane housing with

RO membrane of 40*40 - (1No), RO pressure tube 4" x 1E - ( 1No), 0 - 1200LPH

Rotameter -(2 Nos), with Recovery Rate 50%.

Supplying and erecting Direct - On - Line Starter with 18 A. rating contactor

and with 3.5 Amp. 18A range directly operated in totally insulated elegant

202 enclosure for single phase operation up to 3 HP as per IS 13947 complete 2.00 Ea. 2100.80

erected on P.W. Block with necessary connection. Cat-lll

Providing & erecting open well horizontal mono block pump set with cast iron

body, complete for three phase submersible motor having, [D] For 5 HP

203 phase open well horizontal mono block pump set suitable for 1350 LPM to 310 2.00 Ea. 18746.61

LPM @ 10 to 42 Mtr head suitable for 50/65 mm dia delivery pipe, Cat.II

Supplying & erecting approved make 3 phase motor control cubical panel (

Star - Delta) made from16 G. CRCA sheet duly painted with epoxy powder

painted inside and outside with hinged doors and locking arrangement,

consisting of suitable size of ON- OFF isolator (AC - 3/23 duty) main fuses,

single phasing preventer cum water level. Guard (Complete unit), Toggle

switch to by pass Single phase preventer cum WLG, indicating lamps for R- Y-

B phases, over load relay, Automatic water level controller, Ammeter &

204 Voltmeter each with two way selector switch incoming wires duly socket 1.00 Ea. 18360.79

Crimped, Panel to be erected on angle iron frame grouted on wall as

directed. Star Delta & main contactor, overload relay, thermal / Electronic

Star delta cutoff timer, start - stop push buttons. The isolator overload relay

& contactors of L& T, Siemens or Cuttler Hamer make only. Panel to be

erected on angle iron frame ground on wall. (E) S/D up to 22.5 H.P.

S.I.T.C. submersible pump set for bore of 150 mm. dia. Or more having

phase motor capacity about 20 H.P and discharge capacity having . Lifting

205 and Lowering taken extra. (B) (14 Stage) 650 to 550 LPM discharge at head 84 1.00 Ea. 61011.07

to 112 mtrs suitable for 65 mm dia. delivery pipe, Cat.III

Lowering of submersible motor pump set at the depth of following ,complete

with required. Nos. and size of casing pipes erected by means of proper chain

206 pulley block & pipe wrenches after checking of threads of each pipe with 1.00 Per Job 2568.43

coupling to take the load of the pump set and pipe assembly filled up with

water, (B)Above 60 mtrs. and Up to 120 mtrs.

(D)For Open well Horizontal submersible pump set for sump well, (i) 1 HP

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible

207 Submersible copper cable approved make of following Size. (C) 3 Core x 4 30.00 Mtr. 146.45

207A (D) 3 Core x 6 Sq. mm. 210.00 Mtr. 172.71

Providing Water proof straight Joint in PVC insulated flat flexible copper

208 cable by using insulating material, water proofing material, & making the 3.00 Ea. 189.88

joint complete. (A) Up to 10Sq. mm

Providing & laying approved make ISI marked HDPE 6Kg / cm2 (Class-3) as

per IS:4984:1995 PE-80 to be erected at road crossing on or floor as directed

209 for laying of cable. The pipes as following size of dia & weight per 6 mtr. (C) 90.00 Mtr. 249.47

63 mm inner Dia.

Supplying, installing, testing & commissioning of SOLAR WATER heating

system as per prevailing IS code comprising of Solar flat locket collector,

stainless steel hot water storage isolated tank with S.S. heat exchanger,

absorber made of copper sheet & copper tube of following capacity in liter /

day (LPD) with "B" size aluminium box collector with appropriate capacity

electrical backup arrangement (Excluding inlet & outlet pipe lines) (D)

Capacity of 500 LPD

Supplying & erecting resin bonded flap rock wool / glass wool with

conductivity valve 1.67 sq.mm per watt & to with stand the temp. to

degree centigrade C thickness 50mm with G I pipe of following size dia "B"

211 class as per IS:1239. The plastic sheet to be used as covering of glass wool. 50.00 Mtr 767.60

Al. cladding besides other materials like chicken mesh, 26 G Al. Sheet shall be

used for cladding the insulation pipe. (E) for 50 mm dia pipe

Supplying & erecting 12mm composite pipe manufactured from polythene

material with destructed thermal expansion of 25 10-6 / degree kelvin (low

expansion Co-efficient), resistant to freezing thermal conductivity 0.43 watt

/ (m degree kelvin) UV resistant suitable for continuous operating

temperature of 95 degree centigrade & rated pressure of 6.9 kg / sq.cms at

212 850 degree centigrade. The kitec pipe shall have chemical composition 130.00 Mtr 248.46

prepared as per ASTMF 1282-02 specifications (Pressure rating of 13.8 kg per

sq.cms. & 11 KG per sq.cms at 60 degree) The pipe shall be duly jointed by

comprising crimp fitted with internal as well as external end sealing

arrangement. (B) For 16 mm pipe

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for which no

extra payment shall be made.

The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

GST and Income tax TDS will be deducted at a source while making payments of bills

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017 Cement

Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change as per actual mix design the

cost of difference of cement consumption have been deducted from the rate of original item at the rate of input rate mentioned in all

All work shall be carried out as per P.W.D. Hand Book and other specification of the Division or as directed.

All the columns in the Schedule be filled in ink and the total of the entries in the last column should be struck by the contractor under

Rates quoted include clearance of site (prior commencement of work and at its close) in all respects and hold good for work under all

conditions, site moisture, weather etc.

The contractor shall exhibit the details of work, tender amount, specifications as per Govt. circular No. BDG / 3277 / 1657 Dated. 26-4-

1978 and G.R. No. TNC/ 1090-24 C, Dated. 18-11-91 as directed by the Engineer-in-charge on the work site for which contactor

In R.C.C. item where there is change of grade mix orchange as per actual mix design the difference of of cement consumption shall be

added / deducted from rate of original item at the rate of star rate mentioned in the tender.

For earthquake resistance provision the works shall be carried cut as per the intruction of Engineer in charge.

The other conditions of Schedule "B" will remain unchanged.

Testing of materials shalll be as per statement atteched with the specification. The materials shall be tested in G.E.R.I. bill of testing

charges shall be paid the Executive Engineer and 1 % of the amount put to Tender shall be recovered from the contractor in running bills

is as per G.R. (R&B) Dept. No. TNC 1085 / (4) C Dt. 10-05-85.

Contractor shall even 'NIL' percentage. If deduction is offered.

Deputy Executive Engineer Executive Engineer

( R & B) Sub Division (R & B) Division