WBPWD/SE/SC_SS/NIT12/2025-2026

Scheduled and Non-Scheduled Items (Part - I and Part - II respectively)

Percentage BoQ At Par

BoQ_Ver4.0

Bidder Name :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only)

NUMBER #

Building Works :- Providing Bored Cast-in-situ_M25_grade R.C.C. pile in position asper specifications in all kinds of soil including cost of boring using drillingmud to stabilize the bore and flushing the bore of excess mud with freshlyprepared drilling fluid by using pumps prior to placing concrete by tremiepipe in one continuous operation and including the cost of all materials andlabour for placing of oncrete and also including the cost of mobilization andhire charges of all equipment necessary for boring, welding of reinforcementcage as necessary and lowering of reinforcement cage, preparation andplacing of concrete, including the cost of concrete but excluding the cost ofreinforcement and labour for bending binding etc. complete as per Drawing and Technical Specifications and removal of excavated earth with all lifts andlead upto 1000 m. Work to be executed as per IS: 2911 (Part II Sec 2) (a) Using tripod, winches (i) Pile diameter - 450 mm.

Providing Bored Cast-in-situ grade R.C.C. pile in position asper specifications in all kinds of soil including cost of boring using drillingmud to stabilize the bore and flushing the bore of excess mud with reshlyprepared drilling fluid by using pumps prior to placing concrete by tremiepipe in one continuous operation and including the cost of all materials andlabour for placing of oncrete and also including the cost of mobilization andhire charges of all equipment necessary for boring, welding of reinforcementcage as necessary and lowering of reinforcement cage, preparation andplacing of concrete, including the cost of concrete but excluding the cost ofreinforcement and labour for bending binding etc. complete as per Drawing and Technical Specifications and removal of excavated earth with all lifts andlead upto 1000 m. Work to be executed as per IS: 2911 (Part II Sec 2). (a) Using tripod, winches (i) Pile diameter - 450 mm.

Performing Vertical load test on single Pile inaccordance with IS:2911(Part-IV) by hydraulic jacks on pile/iles with 1.5 times the design load includingpreparation of the head of piles with concrete of the net safe pile vertical capacity of 450 mm dia 28.5m long bored cast in situ pile is 50 T as per soil report mentioned in drawing. (a) Testing load up to 100 T.

Dismantling R.C. floor, roof, beams etc. includingcutting rods and removing rubbish as directed within a led of 75 m. including stacking of steel bars.

Surface Dressing of the ground in any kind of soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed.

Earth work in excavation of foundation trenches ordrains, in all sorts of soil (including mixed soil butexcluding laterite or sandstone) including removing,spreading or stacking the spoils within a lead of 75 m.as directed. The item includes necessary trimming thesides of trenches, levelling, dressing and ramming thebottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1,500 mm.

(b) Depth of excavation for additional depth beyond 1,500 mm. and upto 3,000 mm.

Hire and labour charges for shoring work (including necessary close plank walling, framing, Eucalyptus/Jhou bulla piling, strutting etc) complete as per direction of the Engineer-in-charge for foundation excavation (vertical surface are in contact with supported earth is to be measured.) (This item should be executed on specific direction of the Engineer in charge). (a) Depth upto 1.5 m.

Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches.

Cement concrete with graded stone ballast (40 mm size excluding shuttering) (a) Pakur Variety (i) 1:3:6 proportion

Controlled Cement concrete with well graded stone chips (20 mm nominalsize) excluding shuttering and reinforcement with complete design of concreteas per IS : 456 and relevant special publications, submission of job mixformula after preliminary mix design after testing of concrete cubes as perdirection of Engineer-in charge. (A) Pakur Variety (a) M 25 Grade (i) In Ground Floor

(ii) In 1st Floor

(iii) In 2nd Floor

Hire and labour charges for ttering with centering and necessary agingupto 4 m using approved stout rops and thick hard wood planks of ved thickness with required bracing for (upto roof of ground floor) (a) 25 mm to 30 mm shuttering without staging in foundation

(b) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work (i) In Ground Floor

(ii) In 1st Floor

(iii) In 2nd Floor

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (A) For works in foundation and upto roof of ground floor/upto 4 m (a) Tor steel/Mild Steel (JSW/JSPL/SHYAM/SRMB/BMASL/ELECTROSTEEL/SSL) (i) In Ground Floor

(ii) In 1st Floor

(iii) In 2nd Floor

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) (a) With earth obtained from excavation of foundation

Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and onsolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity)

Anti termite treatment to back filling of the masonry foundation with chemical emulsion by admixing chloropyrofos emulsifiable concentrates ( 1% concentration) with water by weight at the rate of7.5 Litres per sq. m. of the vertical surface of the substructure for each side of the foundation. The workshall be carried out as per specification described in6.2.2. of code IS-6313 (part -II) 1981. (Mode ofmeasurment will be vertical area treated.)

Anti termite treatment to the top surface of the consolidated earth within plinth walls with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weightat the rate of 5 Litres per sq. m. of the surface beforesand bed or sub-grade is laid. Holes upto 50 mm. to75 mm. deep at 150 mm. centre to centre both waysshall be made with 12 mm, diameter mild steel rod onthe surface to facilitate saturation of the soil with thechemical emulsion. The work shall be carried out asper specification described in para 6.4 of code IS-6313 (part -II) 1981. (Mode of measurment will beper Sq.m of plan area of plinth treated.)

Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge.

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.

Integrity testing of Pile using Low Strain / Sonic Integrity Test / Sonic Echo Test method in accordance with IS 14893 including surface preparation of pile top by removing soil, mud, dust & chipping lean concrete lumps etc.

Brick work with 1st class bricks in cement mortar (1:6) (a) In Foundation and Plinth

(b) In Superstructure (i) In Ground Floor

(ii) In 1st Floor

(iii) In 2nd Floor

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) (i) In Ground Floor

(ii) In 1st Floor

(iii) In 2nd Floor

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). (a) Sal : Local (i) In Ground Floor

(ii) In 1st Floor

(iii) In 2nd Floor

Supplying, fitting and fixing fibre reinforced polymer (FRP) Composite door frame as per approved section with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to safisfy IS: 4020 door testing performance criteria. (a) 66mm x 90mm

Supplying, fitting & fixing fibre reinforced polymer (FRP) Composite door shutters as per approved design with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to satisfy IS:4020 door testing performance criteria. (a) 32 mm thick

Welding in M.S. structural work with gas or electric: (a) Tack weld

Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete (1:2:4) asper direction. (Cost of concrete will be paid separately) (a) 40mm X 6mm, 250mm Length

(b) 40mm X 6mm, 125mm Length

Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. (a) 100mm. X 58mm. X 1.90mm.

(b) 75mm. X 40mm. X 1.12mm

Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: (a) 225mm long x 10mm dia. Bolt

(b) 200mm long x 10mm dia. bolt.

Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting. (a) 300mm long

Renewing 125mm long wooden buffer block (a) With Sal : Malayasian

Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: (a) 150 mm grip x 10 mm dia rod.

M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs. (a) Grill weighing above 16 Kg./sq.mtr and above

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary. [Excluding cost of chipping over concrete surface] (A) With 1:6 cement mortar (a) 20 mm thick plaster (i) In Ground Floor

(ii) In 1st Floor

(iii) In 2nd Floor

(b) 15 mm thick plaster (i) In Ground Floor

(ii) In 1st Floor

(iii) In 2nd Floor

(B) With 1:4 cement mortar (a) 10 mm thick plaster (i) In Ground Floor

(ii) In 1st Floor

(iii) In 2nd Floor

18 mm. to 22 mm. thick, kota stone slab set in 20 mm thick(avg) cement mortar (1:4) in floor, stair & lobby includingpointing in cement slurry with admixture of pigment matchingthe stone shade, including grinding & polishing as perdirection of Engineer - in - charge to match with the existing work. (i) In Ground Floor

(ii) In 1st Floor

Extra cost of labour for prefinished and premoulded Nosing to treads of steps, railing, window sill etc. of Kota Stone.

Extra cost of labour for grinding Kota Stone Floor in treads and riser of Steps.

Supplying, fitting & fixing 1st quality Ceramic tiles in wallsand floors to match with the existing work & 4 nos. of keystones (10mm) fixed with araldite at the back of each tile &finishing the joints with white cement mixed with colouringoxide if required to match the colour of tiles includingroughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (A) Wall With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thickcement slurry at back side of tiles using cement @ 2.91Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m (1) Wall Area of each tile above 0.09 Sq.m (a) Coloured decorative (i) In Ground Floor

(ii) In 1st Floor

Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming toIS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. (A) UPVC Pipes (i) 160 mm. Dia.

(B) UPVC Fitting (a) Plain Tee (i) 160 mm. Dia.

(b) Bend 87.5 degree (i) 160 mm. Dia.

(c) Shoe (i) 160 mm. Dia.

Supplying solid flush type doors of commercial quality, the timber frameconsisting of top and bottom rails and side styles of well seasoned timber 65mmwide each and the entire frame fitted with 37.5mm wide battens places both waysin order to make the door of solid core and internal lipping with Garjan orsimilar wood veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fitting. (a) 35 mm thick shutters (single leaf) (i) In Ground Floor

(ii) In 1st Floor

Panel shutters of door and window, as per design (each panel consisting of singleplank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. (A) 35mm thick shutters with 19mm thick panel of size 30 to 45 cm (a) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. (i) In Ground Floor

(ii) In 1st Floor

(iii) In 2nd Floor

Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracings properly rivetted and washered including 38mm steel rollers including locking arrangements, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes, chasing etc. in walls, floors etc. and making good damages complete.

Supplying and laying true to line and level Anti-Skid, Full Body, Homogeneous& Granular finish Vitrified Tiles conforming to IS:15622-2006 & IS 4457-2007and testing shall be made in accordance with IS:13630 [Non- modular sizes fortiles with Skid resistance > 0.5, Mohr's hardness > 5.0, Staining resistance: Class-1, Water Absorption: E < 0.5%], MOR > 35 N/sq.mm in Internal area ofbuilding e.g. Toilet Block, Passage, Corridor, Accessible Open Terrace etc. setin 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side oftiles using cement @ 2.91 Kg./Sqm or using Polymerised Adhesive (6 mm thicklayer applied directly over finished artificial stone floor/ Mosaic etc without anybacking course) laid after application slurry using 1.75 Kg of cement per Sqmbelow mortar only, joints grouted with admixture of white cement and colouringpigment to match with colour of tiles/ epoxy grout materials of approved make asdirected and removal of wax coating of top surface of tiles with warm water andpolishing the tiles using soft and dry cloth upto mirror finish complete includingthe cost of materials, labour and all other incidental charges complete true to themanufacturer's specification and direction of Engineer-in-Charge. (Whitecement, synthetic adhesive and grout material to be supplied by the contractor) (i) In Ground Floor : Sizes-300 mm x300mm x10 mm with breaking strength > 1200 N

(ii) In 1st Floor

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (a) One Coat (i) In Ground Floor

(ii) In 1st Floor

(iii) In 2nd Floor

Protective and Decorative Acrylic exterior emulsion paint of approvedquality, asermanufacturer's specification and as per direction ofEngineer-in-Charge to be applied over acrylic primer as required. Therate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. (a) Premium 100% Acrylic Emulsion (Two Coat) (i) In Ground Floor

(ii) In 1st Floor

(iii) In 2nd Floor

(a) Priming one coat on steel or other metal surface with synthetic oilbound primer of approved quality including smoothening surfaces by sand papering etc.

(b) Priming one coat on timber or plastered surface with synthetic oilbound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved makeand brand including smoothening surface by sand papering etc. includingusing of approved putty etc. on the surface, if necessary :- (a) On timber or plastered surface : With super gloss (hi-gloss) - (i) Two coats (with any shade except white)

(b) On steel or other metal surface : With super gloss (hi-gloss) - (i) Two coats (with any shade except white)

Supplying, fitting and fixing windows and ventilators with or withoutintegrated grills conforming to IS 1038-1975 and manufactured fromrolled steel sections conforming to IS 7452-1974 with non-frictionprojecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening ifrequired, fixing lugs in cement concrete (1:2:4) with stone chips 20mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing. (a) Openable steel windows as per IS sizes with side hung shuttersand horizotal glazing bars. [The extra rate admissible for the openable portion only] (i) In Ground Floor

(ii) In 1st Floor

(b) Two point nose aluminium handle including fitting and fixing.

(c) Steel peg stay 300 mm long including fitting and fixing.

(d) M.S. integrated grill as per approved design integrated with steel window or ventilator, joints continuously welded with M.S. flats and bars. (i) In Ground Floor

(ii) In 1st Floor

Supplying, fitting and fixing in position fibre glass panes of approved quality with resin, nail, clip etc. as per IS:12866-1989. (In all floors for internal wall & upto 6 m height for external wall) (a) 4.0 mm thick (6.72 Kg/Sq.m)

Rendering the surface of walls and ceiling with white cement basedwall putty of approved make and brand(1.5mm thick)

Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface. (a) Two Coats

Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m.

Door stopper.(Brass)

Labour for Chipping of concrete surface before taking up Plastering work.

Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification [Cement to be supplied by the Department]

Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement). (Using grey cement) (a) 25 mm. thick (i) In Ground Floor

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (6mm nominalsize) excluding shuttering and reinforcement,if any, in gound floor as per relevant IS codes. (a) Pakur variety

Sanitary & Plumbing Works :- Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer (a) 2000 litre capacity

Labour for hoisting plastic water storage tank. (a) Above 1500 litre upto 5000 litre capacity. (i) Upto 1st story from G.L.

Labour for punching hole in plastic water storage tank upto 50 mm dia.

Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. (A) CPVC Pipes Class-1, SDR-11 (a) For Exposed Work (i) 25 mm dia.medium quality

(ii) 40 mm dia. medium quality

(iii) 50 mm dia. medium quality

(b) For Concealed Work (i) 15 mm dia. medium quality

(ii) 20 mm dia. medium quality

Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C(1:1.5:3) bottom slab including supplying, fitting andfixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and fefilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. Note:- (i) Finished level of Septic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm. Ventilation pipe &Mosquito proof mesh, should be follwed as per IS:2470,Part- I. Payment will be made separetly on the basis of actual height based on relevant I.S.Code. (a) With Pakur variety. (JSW/JSPL/SHYAM/SRMB/BMASL/ELECTROSTEEL/SSL) (i) For 50 users

Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling,15 mm thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm.thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials. (a) With Pakur variety. (JSW/JSPL/SHYAM/SRMB/BMASL/ELECTROSTEEL/SSL)

Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials. With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia. (JSW/JSPL/SHYAM/SRMB/BMASL/ELECTROSTEEL/SSL)

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 (A) UPVC Pipes (a) Single Socketed 3 Meter Length (i) 75 mm

(b) Double Socketed 3 Meter Length (i) 75 mm

(B) Fittings (a) Plain Tee (i) 75 mm

(b) Door Tee (i) 75 mm

(c) Door Tee(LH) & (RH) (i) 75 mm

(d) Bend 45º (i) 75 mm

(e) Bend 87.5º (i) 75 mm

(f) Door Bend (T.S.) (i) 75 mm

(g) Cross Tee with Door (i) 75 mm

(h) Vent Cowl (i) 75 mm

(I) Pipe Clip (i) 75 mm

(j) Passover (i) 75 mm

Labour for fitting and fixing U.P.V.C. pipes for above ground workincluding cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Engineerin- charge. (Payment will be made on centre line measurement of the total pipeline including specials.) (a) Above ground (i) 110 mm

Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc.

Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint. (a) 630 mm X 450 mm size

Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete. (a) 635 mm X 395 mm X 420 mm

Supplying, fitting and fixing Squating plate with integral flushing in white vitreous chinaware of approved make in cement concrete (6:3:1) with jhama chips complete. (Payment of concrete will be paid seperately). (a) 450 mm X 350 mm

Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. (a) With 'P' trap (with vent)

Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete. (a) E.W.C. (i) Plastic (hallow type) white

Supplying, fitting and fixing Half round channel with or without outlet as required set in cement concrete (6:3:1) with jhama chips complete. (Payment of concrete will be paid seperately). (a) White vitreous chinaware (i) 600 mm X 100 mm

Supplying, fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete. (a) Polythene Flush Pipe

Supplying, fitting and fixing urinal flush pipe fittings of approved brand. (a) C.P. urinal flush pipe fittings range of one

Supplying, fitting and fixing soap holder. (a) PTMT (Prayag or equivalent)

Supplying, fitting and fixing towel rail with two brackets. (a) C.P. over brass (i) 25 mm dia. and 750 mm long

Supplying, fitting and fixing bevelled edged mirror 5.5 mm thick silver red as per I.S. 3438 / 1965 together with brass C.P. hinges. (i) 600 mm X 450 mm

Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only). (i) 40 mm dia

Supplying, fitting and fixing bib cock or stop cock. (a) Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar).

(b) Chromium plated Bib Cock long body with wall flange with aerator (Equivalent to Code No. 512 & Model - Tropical / Sumthing Special of ESSCO or similar brand)

(c) Chromium plated Stop Cock (Equivalent to Code No. 513(A) & 513(B) & Model - Tropical / Sumthing Special of ESSCO or similar).

(d) Chromium plated Concealed Stop Cock (Equivalent to Code No. 514(A) & Model - Tropical / Sumthing Special of ESSCO or similar brand)

(e) Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand).

Supplying, fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. (i) 600 mm long

Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps. (i) 1050 mm long

Supplying, fitting and fixing shower of approved brand and make. (a) Chromium plated round shower with revolving joint 100 mm dia with rubid cleaning system (Equivalent to Code No. 542(N) & Model - Tropical / Sumthing Special of ESSCO or similar brand)

(b) Chromium plated shower arm 240 mm long (Equivalent to Code No. 536(A) & Model - Tropical / Sumthing Special of ESSCO or similar brand).

(c) Hand Shower(Health Faucet) with 1mtr Fexible Tube with WallHook(Equivalent to Code No.573 & Model -ALLIED of Jaquar or similar).

Supplying,fitting and fixing aluminium domical grating (i) 150 mm dia

Supplying, fitting and fixing in position R.C.C. Manhole/ pit cover ofapproved make with rim of approved make (Heavy type) (i) 560 mm dia.

Boundary Wall :- Surface Dressing of the ground in any kind of soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed.

Earth work in excavation of foundation trenches ordrains, in all sorts of soil (including mixed soil butexcluding laterite or sandstone) including emoving,spreading or stacking the spoils within a lead of 75 m.as directed. The item includes ecessary trimming thesides of trenches, levelling, dressing and ramming thebottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1,500 mm.

Earth work in filling in foundation trenches or plinthwith good earth, in layers not exceeding 150 mm.including watering and ramming etc. layer by layercomplete. (Payment to be made on the basis ofmeasurement of finished quantity of work) (a) With earth obtained from excavation of foundation

Supplying and laying Polythene Sheet (150gm / sq.m.) overdamp proof course or below flooring or roof terracing or infoundation or in foundation trenches.

Clearing compound premises of shurbs, plants, jungles etc.by cutting and removing as directed (Specific permission ofEngineer-in-Charge prior to execution will be necessary). (Payment to be made on area cleared)

Cement concrete with graded stone ballast (40 mm size excluding shuttering) (a) Pakur Variety (i) 1:3:6 proportion

Hire and labour charges for ttering with centering and necessary agingupto 4 m using approved stout rops and thick hard wood planks of ved thickness with required bracing for (upto roof of ground floor) (a) 25 mm to 30 mm shuttering without staging in foundation

(b) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge.

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (A) For works in foundation and upto roof of ground floor/upto 4 m (a) Tor steel/Mild Steel (JSW/JSPL/SHYAM/SRMB/BMASL/ELECTROSTEEL/SSL) (i) In Ground Floor

Brick work with 1st class bricks in cement mortar (1:6) (a) In Foundation and Plinth

125 mm. thick brick work with 1st class bricks in cement mortar (1:4)

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary. [Excluding cost of chipping over concrete surface] (a) With 1:6 cement mortar (i) 15 mm thick plaster

M.S.or W.I. Ornamental grill of approved design jointscontinuously welded with M.S, W.I. Flats and bars of windows,railing etc. fitted and fixed with necessary screws and lugs. (a) Grill weighing above 16 Kg./sq.mtr and above

Supplying 1.5mm thick M.S. sheet fitted and fixed on one or bothfaces of M.S./ W.I. gate etc. with point welding at not more than150mm apart complete in all respect as per design including cost ofall labour and materials.

Applying Exterior grade Acrylic primer of approved quality and brandon plastered or cencrete surface old or new surface to receivedecorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly,complete as per manufacturer's specification and as per direction of the EIC. (a) One Coat

Protective and Decorative Acrylic exterior emulsion paint of approvedquality, asermanufacturer's specification and as per direction ofEngineer-in-Charge to be applied over acrylic primer as required. Therate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. (a) Premium 100% Acrylic Emulsion (Two Coat)

Priming one coat on steel or other metal surface with synthetic oilbound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved makeand brand including smoothening surface by sand papering etc. includingusing of approved putty etc. on the surface, if necessary :- (a) On steel or other metal surface : With super gloss (hi-gloss) - (i) Two coats (with any shade except white)

Underground Reservoir :- Surface Dressing of the ground in any kind of soilincluding removing vegetation inequalities notexceeding 15 cm depth and disposal of the rubbishwithin a lead upto 75 m as directed.

Earth work in excavation of foundation trenches ordrains, in all sorts of soil (including mixed soil butexcluding laterite or sandstone) including removing,spreading or stacking the spoils within a lead of 75 m.as directed. The item includes necessary trimming thesides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1,500 mm

(b) Depth of excavation for additional depth beyond1,500 mm. and upto 3,000 mm. but not requiring shoring.

Filling in foundation or plinth by fine sand in layers nt exceeding 150 mm as directed and consolidating the same by thorough saturation withwater, ramming complete including the cost of supplyof sand. (payment to be made on measurement of finished quantity)

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.

Earth work in filling in foundation trenches or plinthwith good earth, in layers not exceeding 150 mm.including watering and ramming etc. layer by layercomplete. (Payment to be made on the basis of measurement of finished quantity of work) (a) With earth obtained from excavation of foundation.

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes. (a) Pakur Variety

Supplying and laying Polythene Sheet (150gm / sq.m.) overdamp proof course or below flooring or roof terracing or infoundation or in foundation trenches.

Hire and labour charges for shuttering with centering and necessary stagingupto 4 m using approved stout props and thick hard wood planks of approvedhickness with required bracing for concrete slabs, beams and columns,lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) (a) 25 mm to 30 mm shuttering without staging in foundation

(b) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work

Controlled Cement concrete with well graded stone chips (20 mm nominalsize) excluding shuttering and reinforcement with complete design of concreteas per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as perdirection of Engineer-in charge. Consumption of cement will not be less than300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis ofpreliminary test and job mix foumula. In ground floor and foundation. [using concrete mixture] (a) Pakur Variety (i) M 25 Grade

Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement). (Using grey cement) (a) 35 mm. thick

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (a) For works in foundation and upto roof of ground floor/upto 4 m (i) Tor steel/Mild Steel (JSW/JSPL/SHYAM/SRMB/BMASL/ELECTROSTEEL/SSL)

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary. [Excluding cost of chipping over concrete surface] (a) With 1:6 cement mortar (i) 15 mm thick plaster

(b) With 1:4 cement mortar (i) 10 mm thick plaster

Brick work with 1st class bricks in cement mortar (1:6) (a) In Foundation and Plinth

125 mm. thick brick work with 1st class bricks in cement mortar (1:4)

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). (a) Sal : local

Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) asper direction. (Cost of concrete will be paid separately) (a) 40mm X 6mm, 250mm Length

Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. (a) 100mm. X 58mm. X 1.90mm.

Panel shutters of door and window, as per design (each panel consisting of singleplank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. (a) 35mm thick shutters with 19mm thick panel of size 30 to 45 cm (i) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak.

Neat cement punning about 1.5 mm. thick in wall, dado, window, sills, floor, drain etc. (NOTE:Cement 0.152 cu.m per 100 sq.m.)

M.S. structural works in columns, beams etc. with simple rolledstructural members (e.g. joists, angle, channel sections conformingto IS: 226, IS: 808 & SP (6)- 1964 connected to one another withbracket, gussets, cleats as per design, direction of Engineer-in charge complete including cutting to requisite shape and length,fabrication with necessary bolting, metal arc welding conforming toIS: 816- 1969 & IS: 1995 using electrodes of approved make andbrand conforming to IS:814- 2004, haulage, hoisting and erectionall complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools andplants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. (a) For structural members of specified sections weighing less than 22.5 Kg./m

Supplying, fitting and fixing PVC pipes of approved make of Schedule 80(medium duty) conforming to ASTMD - 1785 and threaded to match withGI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew,reducing socket, reducing tee, short piece etc. fitted with holder batsclamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings asrequired, jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (a) For Exposed Work PVC Pipes (i) 100 mm dia.

(ii) 150mm dia.

(iii) 40mm dia.

(iv) 50mm dia.

Supplying, fitting and fixing in position C.I. manhole/ pit cover with rim. (a) Round (i) 450 mm X 100 mm X 25 kg (approx)

Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only). (i) 40 mm

Supplying, fitting and fixing check valve (horizontal) G.M. tested to 21 kg per sq. cm. (i) 50 mm

Supply of G.I. short piece of TATA make (Above 50mm & upto150 mm long) (i) 50 mm

Supply of G.I. nipple standard 50 mm long. (i) 50 mm

Supply of G.I. plain equal elbow of approved brand and make. (i) 50 mm

Supply of G.I. union (i) 50 mm

Labour for fitting and fixing G.I. specials including cost of jointing materials. (a) Socket, Reducing socket, Bend, Plain equal elbow, Reducing elbow, Nipple, Short piece (i) Above 25 mm upto 50 mm dia.

Electrical Works :- S&F 3 nos 415V, 100A. Kit Kat Fuse unit with base fixed on the wooden plank, as directed by EIC.S&F wooden board and neutral bar.

S&F wooden plank (size- 3’x2’x3/4”) fixed on wall by 1”x1”x1/4” M.S angle iron frame to G.S (For Kit-Kat fuse Unit)., as directed by EIC.

Supplying and fixing 415V, 100A TPN SFU with sheet steel enclosure on angle iron frame on wal with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating. (L&T/Siemens/ABB)

Supplying and fixing 4-way double door Vertical TPN MCB Distribution board for MCCB incomer with IP-42/43 protection,, on angle iron frame on wall & mending good the damages to original finish incl. Inter connection with suitable size of, spiral link, copper wire and neutral link & provision for earthing attachment. Incoming 100A Four pole MCCB-1no, Outgoing 63A TPMCB-4 no. [Make - Legrand/Siemens/ABB]

S&F 415 V, Horizontal type, TPN MCB DB (6-way) with SS enclosure double-door with IP-42/43 protection, with Four Pole Isolators as incomer and SPMCBs ('C' Curve, 10 KA) as outgoing, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment as per GS. INCOMING-63 A FP Isolator -1 No. OUTGOING-6-32A SPMCB-18 Nos. [Make - Legrand/Siemens/ABB]

Supplying and fixing double door sheet steel (16SWG), powder coated cable end box for TPN DB horizontal / vertical enclosure with IP-42/43 protection, on angle iron frame on wall & mending good the damages to original finish with nuts bolts etc incl. provision for earthing attachment. (a) 4 way VTPN

(b) 6 way HTPN DB

S&F 250V, SPN MCBDB (2+12) way with SS enclosure double-door (Ivory White with IP-42/43 protection with DP Isolators as incomer and SPMCBs ('C' Curve, 10kA) as outgoing, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment as per GS. INCOMING-40 A DP Isolator OUTGOING-12 Nos. 6-10A SPMCB [Make - Legrand/Siemens/ABB]

Supply & Delivery of 1.1kV grade XLPE/PVC insulated A/Al armoured cable as per GS. (Make- Polycab/Gloster/RR Kabel) (a) 4 core 35sqmm (From cutout to Main Switrch and VTPN)

(b) 4 core 16sqmm (VTPN to HTPN)

(c) 2 core 10sqmm (for Pump)

(d) 2 core 6sqmm( For Metal Sign Board)

Laying of above cable of 4Cx 35 sqmm & 4cx 16Sqmm XLPE a/Al cable at an average depth of 75 mm in floor/pavement/wall etc.after cutting floor/ pavement/ wall/ and making holes incl., embedding the cable at an average depth as below and mending good the damages to original finish incl. removing the rubbish.

Laying of one No. cable upto 35 sqmm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed.

S&F and fixing compression type gland complete with brassgland, brass ring & rubber ring for dust & moisture-proof entry. (a) 4 core 35 sqmm

(b) 4 core 16 sqmm

(c) 2 core 10sqmm

(d) 2 core 6sqmm

Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials. (a) 4 core 35 sqmm

(b) 4 core 16 sqmm

(c) 2 core 10sqmm

(d) 2 core 6sqmm

Supplying and fixing MCB SS enclosure with IP-20/30 protection, powder coated provision for two/four pole MCB, concealed in wall after cutting the wall & mending good the damages to original finish incl. painting, connection & provision for earthing attachment. (a) 2 way (For Pump end) (Legrand /Siemens/ABB).

Supplying and fixingc 240V 32A DP MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection. (Legrand/Siemens/ABB).

Supplying & fixing medium gauge GI Pipe ( ISI-Medium) Protection with necessary fittings and jointing metarials as required (a) 40mm

Cutting Channel of size (43 mm x 43 mm) on masonry wall by Electric operated cutting machine incl. supplying & fixing heavy gauge 32/25 mm dia, 3 mm thick Polythene pipe, without earth continuity wire, by means of anchoring chemical (Hilti/Sika) and GI 'U' hooks of 8 SWG incl. supplying and drawing 18 SWG GI wire as Fish wire and mending good damages to original finish by using own tools and tackles, as per GS.

Cutting Channel of size (40 mm x 40 mm) on masonry wall by Electric operated cutting machine incl. supplying & fixing heavy gauge 19 mm dia, 3 mm thick Polythene pipe, without earth continuity wire, by means of anchoring chemical (Hilti/Sika) and GI 'U' hooks of 8 SWG incl. supplying and drawing 18 SWG GI wire as Fish wire and mending good damages to original finish by using own tools and tackles, as per GS.

S&F sheet metal inspection box (16 SWG) of the following sizes flushed in wall by housing the same after cutting brick wall incl. making earthing attachment, painting and mending good damages to building works, incl. S&F bakelite / perspex top cover by Brass screws after making housing for switch by cutting bakelite / perspex cover and making necessary connections as required, as per GS. (a) 100 mm x 100 mm x 65 mm

(b) 150 mm x 100 mm x 65 mm

S&F one way CI Round box with cover concealed in ceiling/wall

S&F two way CI Round box with cover concealed in ceiling/wall

Supplying & Fixing of Box type fan clamp of 150mm dia & 80mm depth made of 16 SWG CRCA sheet with one end duly sealed by cover, properly welded, incl. S&F 12mm dia 600mm long MS rod duly bent by heat treatment at the centre position of rod to grip fan bobbin properly, incl. binding the rod and fan box with reinforcement by 22 SWG steel binding wire, incl. supplying & covering the box with alkathene sheet, placed in order to prevent concrete from entering the box.

Supply & Fixing 240 V, 3 nos. 6A, & 1 no. 20A plug socket with separate 3 nos. 6 A & 1 no. 20A Piano key type switch, indicator & 20A switch type SP MCB (Anchor) on sheet metal switch board embedded in wall incl. S & F 240x200x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required.

Supply & Fixing 240 V, 20A, plug socket with separate 20 A Piano key type switch (Anchor) on sheet metal switch board embedded in wall incl. S & F 150x100x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required.

Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Finolex/Polycab/RR) of the following sizes in the prelaid polythene pipe and by the prelaid GI fish wire and making necy. connection as required as per GS. (a) 2x6sqmm + 1x4sqmm [HTPNDB to SPNDB] [Make-Finolex/Polycab]

(b) 2x2.5sqmm + 1x1.5sqmm [for Power plug, Comp. board]

(c) 3x1.5sqmm

Finising the end of above PVC insulated & unsheathed copper wire as per GS. (a) 2x6sqmm + 1x4sqmm

(b) 2x2.5sqmm + 1x1.5sqmm

Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Finolex/RR Kabel/Polycab) in 19 mm bore, 3 mm thick polythen pipe (for horizontal & vertical run in wall and celing portion through prelaid polythen pipe) complete with all accessories embedded in wall to light/fan/call bell points with Piano key type switch (Anchor make) fixed on sheet metal (16 SWG) switch board with bakelite/perspex (wall matching colour) top cover (3 mm thick) flushed in wall incl. mending good damages to original finish [Average run 8 mtr]

Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Finolex/RR Kabel/Polycab) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall to 240 V 5A 3 pin plug point incl. S&F 240 V 5A 3 pin flush type plug socket & piano key type switch (Anchor make) incl. S&F earth continuity wire, fixed on sheet metal (16 SWG) switch board with bakelite/ perspex (wall matching colour) top cover (3 mm thick) flushed in wall incl. mending good damages to original finish (On Board)

Avg Run-4.5mtr

Supplying & Fixing 240 V AC/DC superior type Ding-Dong Call Bell (Anchor) on HW board incl. S&F HW board.

Supply & delivery of Single LED Fitting (20 watt, 230 V AC, 50 Hz with CCT (5700K -6500K, THD< 10%, built in 2.5 KV SPD) with all accessories and 1 no. polycarbonate LED Tubelight as directed by EIC, Luminious efficacy > 105 & <120 Lumen/watt. The LED luminaves & accessories shall have BEE certification. (Make- Philips (Signify)/ Crompton/ Wipro).

Supply & delivery of Twin LED Fitting (20 watt, 230 V AC, 50 Hz with CCT (5700K - 6500K), THD< 10%, built in 2.5 KV SPD) with all accessories and 2 nos. polycarbonate LED Tubelight as directed by EIC, Luminious efficacy > 105 & <120 Lumen/watt. The LED luminaves & accessories shall have BEE certification. (Make- Philips (Signify)/ Crompton/ Wipro).

Fixing only single/twin fluorescent light fitting suspended 25 cm bellow the ceiling with 2 No. 20 mm dia EI conduit (14 SWG) supports fixed with “L” type MS clamp whose one side fixed on ceiling with sutable size 4 nos. fastener and other side connected with the conduit with suitable size of bolts and nuts incl. S&F EI conduit, “L” type (125mmx125mm) 6mm thick and 25mm with MS clamps and connecting the length of PVC insulated wire and mending good damages to original finish and painting etc. by 2x24/0.20 mm (1.5sqmm.) flexible copper wire of 1.10 mt. length, as per GS.

Supply & delivery of 1200mm sweep 230V AC Ceiling fan complete with all accessories with safety wire & PS 2 type capacitor etc. as directed by EIC. (Make- Crompton Greaves/ Orient/ Usha) (2 years OEM warranty and warranty certificate to be provided).

Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. S&F connecting wire for down rod upto 30 cm incl. painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire, as per GS.

Supply & Fixing Socket type fan regulator (Step type) (Anchor) on existing sheet metal switch board with bakelite/perspex top cover by screw after making housing for regulator knob by cutting bakelite/perspex top cover incl. making necy. connections etc. ( 40nos for new fans and 50 nos for existing fans).

Supply and delivery of 230V 230mm (9") metal body heavy duty Exhaust fan with all necessary accessories, as directed by EIC. [Make: EPC Heavy Duty)]

Fixing only exhaust fan after making hole in wall and making good damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection for exhaust of following diameter: (a) 23 cm (9")

Supply & Fixing louver shutter on wall with necy. bolts & nuts (6 mm dia x 62 mm long) (a) For 23 cm (9") Exhaust fan

S&F of 9W LED lamp on exsting angular batten, as directed by EIC. (Philips/Crompton/Wipro).

Earthing with 50 mm dia GI pipe (ISI-M) 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S&F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground, as per GS.

S&F earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as reqd., as per GS.

Connecting the equipments to earth busbar including S&F 2x8SWG GI (Hot Dip) wire on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as reqd. & mending good damages as per GS.

COMPOUND LIGHTING : Supply & delivery of 250V, 70W LED street light with IP-66, individual Secondary Optics Peanut Lens and Separate Toughned Glass Diffuser, Potted Driver to be used, 8400 lumen (minimum) output fittings, as directed by EIC. [Crompton- CRP-421-70-57-SL-LM-NSG/Philips/Wipro].

Fixing only above light fitting complete with all accessories to be including S&F 40 mm GI pipe (ISI-Medium) quality 2 mts. average length having suitable bend S&F necy. length of 1.5 sqmm PVC insulated single core stranded annealed copper wire and making connections as required and mending good damages to wall incl. painting etc., as directed by EIC.

Providing CC (6:3:1) muffing 600x600x760 mm in size or equivalent size of cylindrical muffing above ground level around the pole base complete with 3 mm thick neatly finished cement plaster all round after dismantling the unserviceable muffing if necessary. (a) Without Loop Box

S & F Single arm Header type bracket having 1.5mts long, 40mm dia GI Pipe ( ISI- M) welded in 100mm dia 0.3mt length GI pipe jacket and 110degree angle in top of the brakcet as per direction of EIC.

Supplying & Fixing GI waterproof type looping cable box size 200x150x100 mm deep having 4 mm thick comprising of one 250V 10A SPMCB unit, one NL on porcelain insulator, one compression type brass cable gland for upto 2- core 16 sqmm PVC/A cable and having lined with rubber gasketted GI top cover with brass machine screws etc., earthing terminal with lug, on steel tubular pole near base, including S&F 40x6 mm thick, MS clamps with bolts, nuts etc. including painting with anticorrosive paint, as per GS.

Wiring by 3x 1.5 sqmm single core PVC insulated copper wire through polythene pipe from loop box to fitting as per GS. [Make-Finolex/RR/Polycab]

Supply & Delivery of 1.1 kv grade 2Cx6 sqmm XLPE-armoured AL. cable, as directed by EIC. [Make - Polycab/RR Kabel/Gloster]

Laying of above 2Cx6 sq.mm. XLPE/Ar. AL Cable on wall/surface incl. S&F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting, as per GS.

S&F of 240V double door Timer DB [equivalent of 2+10 SPNDB] with sheet steel enclosure, pnosphitised powder coated neutral bar, DIN rail with IP-43 potection comprising with 1 no. 240V, 25 A DP MCB , 1 no. 240V, 25A, DP Power Contactor, 1 no. Digital time switch-24 hrs with minimum switching of 15 minutes, 1 no. 240V, 25A SP MCB ('C' Curve 10kA) with inner-outer plate & internal wiring by suitable size of Cu wire incl. 1 no. Auto-Manual bypass toggle switch and provision for earthing attachment, incl. LED indication light for running condition with mechanical locking arrangement as directed by EIC.

Metal Signage Board : S & F cubical shape structure made by 1½" x 1" of 18 Swg holobar. The size of the structure 15' X 4' X 6" (depth) board.S & F 04 nos holobar for extra support of the structure (Front side & back side) & 04 nos of rectangular holobar for jointing the front side & back side of the structure. The structure fabricated by proper welding method and finished as per direction of E.I.C.

S & F of 3 mm thick sign board each consist of 15'x4'x6"size aluminum composite panel (Make Aludacor). ACP sheet to fixed on the front side and back side of the structure & also upper & lower side cover by ACP sheet with proper nut & bolts including finishing all side as per direction of E.I.C.

S & F of the high glossy stainless steel anodized letter has been fabricated from stainless steel with proper ending, granding, finishing & argon welding. The base of the letter 24 SWG & side lapping of the letter 26 SWG. The steel letter are to be fixed on the ACP by screw.Matter will be provided by authority.

S & F of the high glossy stainless steel anodized letter has been fabricated from stainless steel with proper bending granding, finishing & argon welding. The base of the letter 24 SWG & side lapping of the letter 26 SWG. The steel letter are to be fixed on the ACP by screw. SOCIAL WELFARE GOVT. SPONSORED(8" x26=208) FREE PRIMARY SCHOOL(10"x17=170) KAMARHATI, KOLKATA-700058(6" x 24=156)

Supply and Fixing of 40mm X40mm X6mm GI angle (considering l mtr angle weight 3.7 kg)--10mtr =10*3.7=37 kg& 25mmX25mmX3 mm GI angle for LED light support.(considering 1 feet angle weight 30 gm) 60ft50X300gm = 15 Kg

Charges for scafolding arrangement for fixing above signage board.

Supply & delivery of 250V, 50W LED flood light with IP-66, individual Secondary Optics Peanut Lens and Separate Toughned Glass Diffuser, Potted Driver to be used, 6000 lumen (minimum) output fittings, as directed by EIC. [Make : Philips or equivalent spec of Crompton]

Fixing only above Floodlight fittings on top of masonary structure by 3 Nos. 10 mm dia x 87 mm long rag bolts, nuts & double washers complete either 37 mm x 10 mm MS flat support/or by other means as required.

Transportation charge for upto 15kms from site and workshop.

Item Rate BoQ

BoQ_Ver4.0

Bidder Name :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only)

NUMBER #

Pump Motor :- Supply and delivery of 3 ph/3.440 V, 3HP,Submersible pump motor set Make KSB (Model no.6"UQD 182/4+UMAI 150-2/22)having delivery outlet 50mm complete in all respect including taxes and duties as per specification and direction of EIC .

Lowering, installation and commissioning of subermersible pump motor set after taking delivery of the pump as directed with necessary electrical works, fitting s etc. excluding the cost of pump, cable and starter but including cost of carrige, labour,tools and plants taxes as applicable as per satisfaction and direction of EIC.with column pipe with necessary tripod arrangement with CO's won tools and tackles, chain pully as requied as per direction of EIC. (a) 3 ph. 440V,3HP Submersible pump motor set.

Supply, delivery and installation of starter DOL star(L&Tmake) with appropriate relay range.

Supply, delivery and installation of single ph submersible pump controller (L&T/KSB Make) with appropriate rating.

Supply, delivery and fixing of 4.0 Sq.mm 3Core flat PVC cable (Finolex or equivalent) for submersible pump motor set.

Supply, delivery and fixing of 2.5.0 Sq.mm 3Core flat PVC cable (Finolex or equivalent) for submersible pump motor set.

Fire Fighting System :- Supply, fitting, fixing of Co2 TYPE EXTINGUISHERS ISI Marked Co2 type Fire Extinguisher 4.5 9 kg. capacity conforming to IS : 15683 : 2006 made from seamless cylinder conforming to IS : 7285 duly approved by Chief Controller of Explosive, Nagpur fitted with ISI Marked Controlled Valve conforming to IS : 3224 high pressure 1 mtr. long discharge hose and horn complete with initial gas charged with carring handle and wall mounting bracket valuable operating between -3000 C to +5500C Fire rating Class - 13B complete in all respect including all taxes and in all floors.

Supply, fitting, fixing of POWDER TYPE EXTINGUISHERS (DCP Cartridge Type) ISI Marked Powder type Fire Extinguisher for Class B & C fire 9 kg. capacity fitted with Forged Brass squeeze lever discharge valve conforming to IS : 15683 : 2006 complete with initial refill consisting of ISI Marked Co2 gas Cartridge of 200 grams capacity conforming to IS : 4947 and ISI Marked Sodium base dry chemical powder conforming to IS : 4308 suitable for operating between -3000 C to +5500C Fire rating Class - 34B complete in all respect including all taxes and in all floors.