Construction work for Class Rooms in the Girls School Run By The Bhabhar Lokniketan Trust At-Bhabhar Nagarpalika Dist :- Vav Tharad

Excavation for foundation up to 1.5 M Depth including sorting

out and stacking of useful materials and disposing of the

excavated stuff up to 50 meter lead (A) Loose or soft soil

Filling available excavated earth (excluding rock) in trenches,

plinth, sides of foundations etc. in layers not exceeding 20 cm.

in depth consolidation each deposited layer by ramming and

Filling in foundation and plinth with murrum or selected brout

for out side soil in layers of 20 cm. thickness including

watering, ramming and consolidating etc. Complete.

Carrying out plinth treatment to post constrution/existing

structrue by spraying chemical solution for termite control

treatment including labour and material consistent with I.S.I

specification.using chordeneand chiorpuffiles 20 EC as per

6131_paret - II consentration Weight One percent is

recommended i.e one liter 20EC chemical emulsion with

19liter give 1% concrentration inclusive of one liter chemical

emulsion appication at the rate of 5 liter chemical /Sqm of

Sarface is recommended as per I.S.

Providing and laying cement concrete 1:4:8 (1- Cement : 4-

coarse sand : 8- hand broken stone aggregates 40 mm

nominal size) and curing complete excluding cost of formwork

in (A) Foundation and Plinth (upto 10 ton)

Providing and laying cement concrete 1:2:4 (1- Cement :

Coarse sand : 4- graded stone aggregates 20 mm nominal size)

6 5.00 and curing complete excluding cost of formwork in (A) 3638.79 Cu.Mt

Foundation and Plinth

Providing and laying cement concrete work 1:2:4 (1- Cement :

2- Coarse sand : 4- graded stone aggregates 20 mm nominal

size) and curing complete excluding cost of formwork and

reinforcement for reinforced concrete work in (D) Columns,

Pillars posts and struts upto floor two level.

Providing and laying cement concrete work 1:2:4 (1- Cement :

2- Coarse sand : 4- graded stone aggregates 20 mm nominal

size) and curing complete excluding cost of formwork and

8 16.00 reinforcement for reinforced concrete work in (B) Slabs, 4023.42 Cu.Mt

landing, shelves, Balconis , Lintels, Beams, Girders and

Cantilever upto floor two level

Brick work using common burnt clay building brick having

crushing strength not less than 35 kg/sq. cm. in foundation

and plinth in cement mortar 1:6 (1 Cement : 6 fine sand) (b)

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)

Extra for brick work in superstructure above plinth level upto

floor two level (B) Conventional(upto 10 ton)

Providing TMT Bar FE 500D reinforcement for R.C.C. work

11 2050.00 including bending, binding and placing in position complete 77.29 Kg

upto floor two level

Providing 10mm thick cement plaster in single coat on

brick/concrete wall for interior polastering up to floor two

level and finished even and smooth with (II) cement mortar

1:3 (1 cement : 3 sand) curing etc. Completed as approved by

the Architect and Engineer-in-charge, For all floor

Providing 15mm thick cement plaster in single coat on

brick/concrete wall for interior polastering up to floor two

13 95.00 level and finished even and smooth with (II) cement mortar 165.02 Sq.Mt

1:3(1 cement : 3 sand) curing etc. Completed as approved by

the Architect and Engineer-in-charge,

20 mm. Thick sand faced cement plaster {GUTKA} on walls

upto All height above ground level consisting of 12 mm. Thick

backing coat of c.m. 1:3 (1 cement : 3 sand) and 8 mm. Thick

14 130.00 finishing coat of c.m. 1:1 (1 cement : 1 sand) etc. Completed 320.70 Sq.Mt

as approved by the Architect and Engineer-in-charge,

Providing and laying polished Kota stone slab flooring over

20mm (Average) thick base of cement mortar 1:6 (1-

cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 -

15 38.00 coarse sand) laid over and jointed with grey cement slurry 1018.88 Sq.Mt

mixed with pigment to match the shade of slab including

rubbing and polishing etc. complete. (A) 25mm thick

Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall

16 261.00 surface to give an even shade including throughly brushing 83.18 Sq.Mt

the surface free from mortar droppings and other foreign

matter and sand papered smooth.

Extra for Providing formwork with sheathing steel sheets so as

17 10.00 to give a fair finish in (A) Foundations, Footings, Bases of 98.84 Sq.Mt

Columns etc. and Mass concrete (upto 10 ton)

Extra for Providing formwork with sheathing steel sheets so as

to give a fair finish in (B) Flat surfaces such as soffits of slabs

Landings and the like. 2) Floors etc.above 200mm in

thickness. (upto 10 ton)

Extra for Providing formwork with sheathing steel sheets so as

to give a fair finish in (G) Columns, Pillars, Posts and struts. (1)

Square, Rectangular or polygonal in plan. (upto 10 ton)

Providing and fixing M.S. door and window prepared with

ms equal angle for frame and shuter with 18 BSG. Sheet

20 3.00 Including Fixture and fastening Including Red lead paint 2940.11 Sq.Mt

with two coat oil paint etc. Including fixing in position .(As

Providing and fixing M.S. window with Ms Grill prepared

with ms equal angle for frame and shuter with 18 BSG.

21 9.00 Sheet Including Fixture and fastening Including Red lead 4592.47 Sq.Mt

paont with two coat oil paint etc. Including fixing in

position .(As per R.A.)

Providing and laying broken chine mosaic flooring for

terrace using 12 mm to 20 mm broken pieces of glazed tiles

to be laid over cement mortar 1:3 to plain or slope and to

be tempered to bring mortar creme out upto surface using

white cement including rounding off junctions and

extending them upto 15 cm along the wall, clearing with

water and oxalic acid etc. as directed.

Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multistrand copper wires, in below type of pipe erected

with 6A Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC / Metallic/Wooden

22 10.00 box, single mounting base frame covered with textured/metallic front 419.15 Pt.

plate modules erected on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector as directed. (f)

with medium class Rigid PVC pipe and accessories erected concealed

in wall/ceiling complete Cat. III

Electrical Sor 2022-23 Section -1 -2-

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm

(Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated

multistrand copper wires, in below type of pipe erected with 6A

Modular type switch and hum free EME four or more step type

electronic fan regulator with separately mounted and accessories

23 3.00 with earth continuity of following type erected on PVC / 598.93 Pt.

Metallic/Wooden box, single mounting base frame covered with

textured/metallic front plate modules erected on / in wall / ceiling as

per pipe erected. with necessary ceiling rose / H.D.Connector as

directed. (f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat. III

Point wiring for Looped Plug with 6A Modular type switch & 5 pin

socket erected on PVC / Metallic/Wooden box, single mounting base

24 3.00 frame covered with textured / metallic front plate modules erected on 241.39 Pt.

/ in wall / ceiling with following type accessories Cat. III

Supplying and erecting LED indoor fittings with LEDs of wattage

Watt to 0.5 Watt assembled on single MCPCB, with housing used as

a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name 160V to

270V, Power Factor more than 0.9, THD < 15%,

CCT 3000 K to 6500K,

25 2.00 Luminaire efficacy> 85 lumens/watt ,LED 165.64 Ea.

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.) (i) 5-10 Watts, Surge-2 KV, IP-20,

conventional 1 to 2 feet Cat-lll

Electrical Sor 2022-23 Section 2-15-1 (i)

Supplying and erecting LED indoor fittings with LEDs of wattage

Watt to 0.5 Watt assembled on single MCPCB, with housing used as

a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name 160V to

270V, Power Factor more than 0.9, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.) (iv) 22-24 Watts, Surge - 2KV,IP-20,

conventional 4 feet Cat-lll

Approved make Earth fault Relay suitable to mount with inter

connection to moulded case circuit breaker having CT ratio &

27 1.00 MCCB rating as following along with shunt trip 220V AC. with all 4983.34 Ea.

internal connections & complete erected in existing M.S.housing..

Providing and erecting Sheet Steel powder coated MCB distribution

board - flush / surface mounted fitted with busbar, neutral link, earth

bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without

MCB to house appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used)

(A) Single phase 4 way single door

Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250 Micron

galvanising, connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber

and heavy duty cover.(approved make OEM has to submit test

29 1.00 certificate) & having back filling compound of (B) Inner chemical 4591.46 Ea.

(CCM Compound)- Resistivity:- 0.2 / meter testing as per IEC

62561-2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar

content:- <2%(C) Back fill Compound :- Earthing compound should

be capable to retain moisture for long time Necessary test report

must be submitted.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing & erecting Approved make Ceiling Fan with double ball

bearing ISI mark with Condenser 230 volt A.C.50 Hz. 1200 mm

30 4.00 sweep complete having 4 blades Aluminium body and blade sets 2358.35 Ea.

having ornamental design shanks, canopy erected with earthing [

Make shall be approved by Engineer in Charge]

Supplying and erecting 19 / 20 mm. nominal bore Medium Class

31 4.00 M.S. Pipe down rod erected duly painted for fan complete with 108.07 Mtr

proper insulation without leakage and earthing.

Supplying & erecting Fan Hook of 10 mm M.S. Round bar

grouted in RCC slab with Making the site as original.

Supplying & erecting fan hook box of 10 mm M.S. round

bar bounded to the RCC bars up to 50mm length each side

33 4.00 and pierced through a 16 Gauge M.S. box / Heavy Duty PVC 108.07 Ea.

box complete erected concealed in Ceiling with necessary

Providing Fan clamp of 30 x 5 mm flat of required length &

34 4.00 10 mm M.S. Bolt & Nuts erected with necessary hook of 10 98.98 Ea.

mm M.S. Round Bar.

Providing 2.5mm.thick laminated acrylic sheet to cover the

fan hook or Fan box.

Add 18.00 % GST

Add PMC & TPI Charges @ 3.00 %

I/We am/are willing to carry out the work at .............................................% above/below percent

Estimated amount Estimated amount

Put to tender Rs……………………… Put to tender Rs………………………

Deduct .............% below Rs………… Add............% above Rs……………

Total Rs………… Total Rs……………

(*Please strike out whichever is not applicable).

from Contractor's

Works Department

Bill Handbook and other specifications of Division or as directed