Completion of balance work of 0.17 MGD Rapid Sand Filtration Plant at Hakbara for WSS Pehlipora Chandergeer. Under Languishing .

Amount

Earth work in excavation by manual means over areas (exceeding 30cm and up[to 1.5mtr in depth, 1.5mtr in width as well as 10 sqm on plan) including disposal of excavated earth upto 1mtr from cutting edge disposal earth to be levelled and neatly dressed . All kinds of soil

Extra for additional lead beyond 25m (2nd lift)

Providing and laying stone soling hand packed on level.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work upto plinth level 1 : 4 : 8 (1 cement : 4 fine sand : 8 graded stone aggregate 40mm nominal size) crushed.

Providing and laying in position specified grade of reinforced cement concrete excld. the cost of centring, shuttering, finishing and reinforcement. All work upto plinth level. 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone agg. 20mm nominal size)

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc upto floor five level excluding cost of centering, shuttering finishing and reinforcement 1 : 1.5 : 3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete (T.M.T bars)

Centering and shuttering including strutting, propping etc, and removal of form for: Foundations, footings, bases of columns etc., for mass concrete.

Centering and shuttering including strutting, propping etc, and removal of form work for: Walls (any thickness) including attached pilasters, buttresses, plinth and string courses

12mm cement plaster of mix: 1 : 4 (1cement : 4 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering. All work upto plinth level. 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone agg. 20mm nominal size) Crushed

Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc as required. In gratings, frames, guard bars, ladders, railings, brackets, gates and similar works.

Providing and fixing 250mm dia M.S tail pieces made out of 6mm thick pipe incld. cost of 02 No flanges on either side, 16mm thich welded to tail piece, 60cm long incld. cost of of one coat of red oxide primer complete job.

Providing and fixing 200mm dia M.S tail pieces made out of 6mm thick pipe incld. cost of 02 No flanges on either side, 16mm thich welded to tail piece, 60cm long incld. cost of of one coat of red oxide primer complete job.

Providing and fixing 150mm dia M.S tail pieces made out of 6mm thick pipe incld. cost of 02 No flanges on either side, 16mm thich welded to tail piece, 60cm long incld. cost of of one coat of red oxide primer complete job.

Providing and fixing 100mm dia M.S tail pieces made out of 6mm thick pipe incld. cost of 02 No flanges on either side, 16mm thich welded to tail piece, 60cm long incld. cost of of one coat of red oxide primer complete job.

Providing and fixing of M.S flanges to 200mm dia C.I/D.I pipes, including cutting of threaded portion having flanges thickness 12mm incld. cost of rubber insertion, cost of flanges, nuts, bolts and laying in trenches incld. all carriages involved upto actual site of work as directed by site Engineer.

Providing and fixing of M.S flanges to 150mm dia C.I/D.I pipes, including cutting of threaded portion having flanges thickness 12mm incld. cost of rubber insertion, cost of flanges, nuts, bolts and laying in trenches incld. all carriages involved upto actual site of work as directed by site Engineer.

Providing and fixing of M.S flanges to 100mm dia C.I/D.I pipes, including cutting of threaded portion having flanges thickness 12mm incld. cost of rubber insertion, cost of flanges, nuts, bolts and laying in trenches incld. all carriages involved upto actual site of work as directed by site Engineer.

Providing, laying inclduing shourding of filter media of various grades as per COHEEO mannual including coarse sand freee from any impority incld. all carriages from Ganderbal Sindh Nallah quarryu upto actual site of work complete

Providing and fixing of aluminium framed lid over clear water chamber including cost of 5mm thick glass, including cost of all fitting and locking arrangements complete job as directed by site Engineer (450x900mm size)

Providing and fixing of double flanged C.I sluice valve conforming to I.S 780 of 1984 standard make kirlosker PNI type incl. cost of nuts, bolts, R.I cloth all sorts of carriages upto site of work, cost of pedestal tail pieces all leads etc complete job . i) 150mm dia

Connecting of filter beds with clear water chamber by way of providing and fixing of 250mm dia D.I/C.I/M.S pipe incld. all fittings charges complete job as directed by site Engineer incharge

Providing and fixing paneled or paneled and glazed shutters for doors, windows and clerestory windows including ISI marked M.S pressed Butt hinges bright finished of required size with necessary screws excluding paneling which will be paid for separately, all complete as per direction of Engineer incharge. First class kail wood

Providing and fixing glazed shutters for doors, windows and clerestory windows using 10kg/sqm (4mm thick) float glass panes including ISI marked M.S pressed butt hinges bright finished of required size with necessary screws. First class kail wood

Providing and fixing aluminium tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc complete 100 x 10mm

Providing and fixing aluminium tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc complete 150 x 10mm

Providing and fixing aluminium handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc complete 100 mm

Providing and fixing aluminium handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc complete 125 mm

Providing and fixing of link lock/paddal lock of stainless steel 250mm long

Providing and fixing of paneled or paneled and glazed shutters for doors, windows in ply wood supplying. 4mm thick float glass panes with beadings

Marble stone flooring with 16mm (average) thick marble stone (sample of marble shall be approved by Engineer incharge) over 20mm (average) thick base of cement mortar 1 : 4 9 1 cement : 4 coarse sand) laid and jointed with cement slurry including rubbing and polishing complete with. Makrana Doongri adanga veined

Extra for nosing in marble stone for treads

Structural steel work in single section fixed with connecting plate for truss work incld. cutting, hoisting, fixing in position and applying a priming coat of red oxide steel primer

Providing corrugated G.S sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63mm thick with zinc coating not less than 275gm/m2

Providing ridges or hips of width 60cm over all width plain G.S sheets with polymer coated J or L hooks, bolts and nuts 80mm dia G.I limpet and bitumen washers complete job

Providing and fixing of ceramic glazed floor tiles (thickness to be specified by the manufactures) of Ist quality conforming of IS : 13755 of NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in colour such as White, Ivory, Gray, Fume Red brown laid on 20mm thick bed of cement mortor 1 : 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc complete.

Providing and fixing of heating electrical points incld. cost of wire switches, necessary MCB’s, switches, switch boards, ceiling roses reputed make ISI mark screws, casing/conduit material of all sorts of carriage and labour charges required for the job. Heating points

Providing and fixing of electrical lightening points incld. cost of wire switches, necessary MCB’s, switches, switch boards, ceiling roses reputed make ISI mark screws, casing/conduit material of all sorts of carriage and labour charges required for the job. Lightening points

Providing and fixing of electric service line using 16mm square cable of copper from main transformer including fixing of main switch board/pannel board to be fixed in a proper site with bus bars incld. cost MCCB/MCB"S required for individual circuit. The length of the service line is about 75Mtrs complete job as directed by site Engineer

Applying one coat of water thinable cement primer of approved brand and manufacture on wall surface. Water thinable cement primer

Finishing walls with water proofing cement paint of approved brand and manufactured of required shade to give an even shade new work(two or more coats) applied @3.84kg/10sqm

Applying priming coat: with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

P/F of air blower Everest make ISI mark capable of providing compression @ 600-900 LPM/m2 @ 0.35kg/cm2 coupled with suitable 3 phase induction electric motor Kirlosker/Cormpton/ Graves etc make complete with auxiliary pipe system upto both filter beds, fitting pressure gauge, nozzles, cement concrete, block, base plate air check valve, non-return valve, sluice value, complete job

Providing, installation and successful commissioning of M.S rotating dislodging bridge moving on rent, fixed on peripheral beam of the clarifloculator with well designed M.S frame base with hand railing, chequered plate flooring complete job with suitable reduction gear arrangement coupled. 3 HP 3 phase gear induction motor of kirlosker/greaves/Crompton make complete job (dia:10.6m)

Providing, fixing and testing and commissioning of churners of floculator with three phase induction motor, 2 HP capacity with intake reduction gear system complete job as directed by site Engineeer

Providing and fixing of churners to alum and bleaching tanks with all arrangements for water bleading system with churners of 3 phase induction motor 1 HP capacity incld. tetsing and commissioning of system complete job as directed by site Engineer

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m

Carriage of materials by Mechanical transport from source to actual site of work including loading, unloading and stacking of material: Cement/Steel for avg. lead 25 kms

Carriage of materials by Mechanical transport from source to actual site of work including loading, unloading and stacking of material: Sand for avg. lead 5 kms

Carriage of materials by Mechanical transport from source to actual site of work including loading, unloading and stacking of material: Aggregate for avg. lead 25 kms

Carriage of materials by Mechanical transport from source to actual site of work including loading, unloading and stacking of material: Soling for avg. lead 10 kms

ABDUL RAHMAN GANAI

M/S MAJID AND CO