Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹8.9 CrAdmitted-Finance AMLA TOLA CHAIBASA DIST WEST SINGHBHUM JHARKHAND 833201 | CHAIBASA | WEST SINGHBHUM | JHARKHAND | 833201 | ₹8.9 Cr | L1 | Admitted-Finance |
| 2 | L2₹9.3 CrAdmitted-Finance M 13 S S HARMU HOUSING COLONY RANCHI DORANDA ARGORA RANCHI | ₹9.3 Cr | L2 | Admitted-Finance |
| Sl No | Description | Qty | Unit | M/s Satyam Builders L1 | M/S MANOJ KUMAR PANDEY L2 |
|---|---|---|---|---|---|
| 1.00 | Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 m including all lifts, levelling , ramming the foundation trenches, removing roots of trees, serbs all complete as per approved design,building specification & direction of E/I. | 1,594.64 | m3 | 143.3 ₹2.3 L | 148.91 ₹2.4 L |
| 2.00 | Extra for earthwork in hard soil as per specification and direction of E/l (vide classification of soil item-B) hard soil @ 80% of tatal Excavation | 1,007.93 | CUM | 14.64 ₹14,756.10 | 15.21 ₹15,330.62 |
| 3.00 | ExcavationinOrdinaryRockwith Dozer with lead upto100metres(Excavation for roadway inordinary rock by deploying a dozer,80HP including cutting and pushing the cut earth to site of embankment up to a distance of 100 metres (averagelead50metres) ,trimming bottom and side slopes in accordance with the requirements of lines, grades and cross sections.) | 314.98 | CUM | 164.33 ₹51,760.66 | 170.76 ₹53,785.98 |
| 4.00 | Providing coarse clean local sand in filling in foundation trenches or in plinth including ramming and watering in layer not exceeding 150mm thick with all leads and lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer Incharge (Mode of measurement compacted volume)Sand filling in Foundation, Flooring and Below Tai Beam | 186.35 | CUM | 556.44 ₹1.0 L | 578.19 ₹1.1 L |
| 5.00 | Providing designation 75A one Brick Flat Soling joints with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I | 1,764.96 | SQM | 336.52 ₹5.9 L | 349.67 ₹6.2 L |
| 6.00 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) | 3.43 | Cum | 4,340.27 ₹14,887.13 | 4,509.94 ₹15,469.09 |
| 7.00 | Providing And Fixing in position cement concrete of specified grade excluding the coast of centering and shuttring -All work up to plinth level . | 147.35 | Cum | 4,250.79 ₹6.3 L | 4,416.96 ₹6.5 L |
| 8.001:2:4 (1 cement :2 coarse sand(Zone-III):4 graded stone aggregate 40mm nominal size) | |||||
| 9.00 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) | 7.49 | Cum | 3,893.97 ₹29,165.84 | 4,046.2 ₹30,306.04 |
| 10.00Centering and shuttring including,propping etc and removal of from for | |||||
Tender Value
Refer Docs
EMD Value
₹9.4 L
Closing Date
27 Nov 2025, 5:00 pmClosed
Nodal Officer
e-Procurement Cell, Jharkhand State Building Construction Corporation Ltd., Beside Jharkhand Mantralaya, Dhurwa, Ranchi-834004.
Construction of Hostel at Degree College, Manoharpur at Chaibasa District under Kolhan University, Chaibasa
2025_JSBCC_106392_1
JSBCCL/41/2025-26
Open Tender
Civil Works - Buildings
330 days
West Singhbhum
Please refer Tender documents.
4 documents required · 4 mandatory
₹10,000
₹9.4 L
10 Dec 2025
7 Nov 2025
28 Nov 2025
7 Nov 2025
27 Nov 2025
7 Nov 2025
Amount
Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 m including all lifts, levelling , ramming the foundation trenches, removing roots of trees, serbs all complete as per approved design,building specification & direction of E/I.
Extra for earthwork in hard soil as per specification and direction of E/l (vide classification of soil item-B) hard soil @ 80% of tatal Excavation
ExcavationinOrdinaryRockwith Dozer with lead upto100metres(Excavation for roadway inordinary rock by deploying a dozer,80HP including cutting and pushing the cut earth to site of embankment up to a distance of 100 metres (averagelead50metres) ,trimming bottom and side slopes in accordance with the requirements of lines, grades and cross sections.)
Providing coarse clean local sand in filling in foundation trenches or in plinth including ramming and watering in layer not exceeding 150mm thick with all leads and lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer Incharge (Mode of measurement compacted volume)Sand filling in Foundation, Flooring and Below Tai Beam
Providing designation 75A one Brick Flat Soling joints with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)
Providing And Fixing in position cement concrete of specified grade excluding the coast of centering and shuttring -All work up to plinth level .
1:2:4 (1 cement :2 coarse sand(Zone-III):4 graded stone aggregate 40mm nominal size)
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)
Centering and shuttring including,propping etc and removal of from for
Foundation,footings below bases of coluumn etc for mass concrete.
Providing and laying cement concrete in retaining walls, return walls,walls (any thickness) including attached pilasters, columns, piers,abutments, pillars, posts, struts, buttresses, string or lacing courses,parapets, coping, bed blocks, anchor blocks, plain window sills, fillets,sunken floor,etc., up to floor five level, excluding the cost of centering,shuttering and finishing :1:1½:3 (1 cement:1½ coarse sand:3 graded stone aggregate 20 mm nominal size)
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level
1:11/2:3 (1 cement :11/2 coarse sand (Zone-III):3 graded stone aggregate 20mm nominal size)
Centering and shuttring including,propping etc and removal of from for
Foundation,footings below bases of column etc for mass concrete.
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :
Centering and shuttring including,propping etc and removal of from for
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
Centering and shuttring including,propping etc and removal of from for
lintel,beams,plinth beam,girders,bressumers and cantilevers
Centering and shuttring cluding,propping etc and removal of from for
Suspended floors,roofs,landigs,balconyes,and acess platform
Centering and shuttring incuding,propping etc and removal of from for
Stairs,(excluding landings)excepts spiral staircases
Centering and shuttring incuding,propping etc and removal of from for
Centering and shuttering including strutting, propping etc. and removal of form work for : Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets,kerbs and steps etc.
Providing TMT reinforcement of following dia rods as per approved design and drawing including carriage of M.S. rods of (Straight or in coils) to work site, cutting, bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I. TMTC-500 8mm dia
Providing tor steel reinforcement rods as per approved design --do-- tht fe 500(only valid for tata(tiscon),sail, jspl,electeo steel, ltd.bokaro and vizag (RINL)
TMTC-500 10mm dia
TMTC-500 12mm dia
TMTC Fe-500 16mm dia
TMTC Fe-500 20/25mm dia
Water proofing for old and new roof slab:- providing and laying water proofing treatment on roof slab by appling two component,factory designed ready to use acrylic modified flexible materials applied with …
Covering of treated surface with PCC :- Providing 25 mm thick Cement Concrete M20(1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm
Extra for providing and mixing water proofing material 'Impermo' or equivalent in cement concrete work @ 1 kg per 50kg of cement.
Providing and filling of 6 mm thickGroove between 25 mm PCC Panels with Polysulphide Sealant (Poring Grade)as per drawings and technical specifications and direction of E in Charge.(with 18%
Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp of internal dia 140mm, 73mm height, top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3mmdia. round headed screws, one lock at the corners. Clamp shall be made of 12mm dia M.S. bar bent to shape as per standard drawing.
Earth filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)
Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with floating coat of neat cement, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I (Cost of Cico will be paid separately)
Providing designation 75 A brick work in C.M. (1:4) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.
Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.
Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).
Providing designation 75B brick work in CM (1:6) in Foundation with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.
Providing designation 75A brick work in CM (1:6) in superstructure with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.
Providing 125mm thick reinforced designation 75A brickwork in C.M. (1:4) in Superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, cost of materials, racking out joints to 15mm depth, carriage, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.
Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 and including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I
Providing 6 mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I.
Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/l.
Supplying, fitting and fixing M.S. grill gate with M.S. grill made of 20X6mm M.S. flats or 16mm M.S. square bars fitted on 25X25X6mm M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.
Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.
Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.
Provideing 25 mm thick water proff plaster (1:3) with clean coarse sand of F.M 1.5 with 5% cico or any other apporoved water proffing compound including screening , curing with all leads and lifts of water scaffolding taxes and royalty all complete as per building specefication and direction of E/I
Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.
Supplying, fitting and fixing 35mm thick solid core type non-decorative double leaf flush shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.
Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.
Suppling, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows, skylight, fanlights and celetial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l
Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/clerestory windows & desertory other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.
Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/ mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)
Powder coated aluminium (minimum thickness of powder coating 50 micron
Providing and fixing reflective glazing in windows with 5mm thick of ST-167-sparkling Ice/ or Equevalant with EPDM rubber / neoprene gasket etc. all cost complete as per architectural drawing and the direction of E/I
Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I.
Supplying, fitting and fixing 20 guage G.C.I, sheet gate fitted on M.S. Angle frame of size 60x60x6mm. including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l.
Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws win rubber stopper
Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.
Providing and laying doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm
Total
Providing and laying doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm
Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete.
Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I. With commercial grade colour 15X15cm Tiles.
Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Udaipur green marble
Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l.
Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:
New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)
Providing primer one coat of red lead paint ofapproved make over steel surface including preparing the surface after cleaning removing dirt, scales, grease and sand papering, including cost of scaffolding etc. all complete as per building specification direction of E/I.
Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.
Providing & fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS 13592 Type A including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion. Single socketed pipes. 110mm dia
Providing & fixing on wall face unplasticised- PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes conforming to IS 13592 Type A including jointing with seal ring conforming to IS 5382 leaving 10mm gap for thermal expansion
Bend -110 mm
Shoe - 110mm
Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.
Supply fitting and fixing 20mm thick solid core type non decorative double leaf flush shutters in cup borads with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneered of stadard make with oxidesed iron fittings -do-
Supplying & Fixing C.I. Cover without frame -do-do- all complete job 455mm x 610 mm Rectangular
Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg
Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20x20 mm Square Bar
Providing and fixing S.W. intercepting trap in manholes with stiff mixture of cement mortar 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 150 mm Dia
Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.
Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750 mm deep, 600 x 450 internal dimension having 250 mm wall thickness in cement mortar ( 1:6 ) including 12 mm cement plaster ( 1:4 ) with punning on inside and cement plaster (1:6 ) with 600 x 475 mm G.I. cover with frame (Weight not less than 36 Kg.) in foundation and refilling all complete as per specification and direction of E/l.
Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia
Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete. 150 MM dia R.C.C. pipe 150 mm dia. R.C.C. pipe
Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.
Group-A
Twin Control Point Wiring in PVC Conduit, with Modular type Switch: Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, 2 way modular type switch, modular plate, suitable size of GI box etc as required.
Power Plug wiring in PVC Conduit (2X4 Sq.mm) :- Wiring for light/power plug with 2x4 Sq.mm FR PVC insulated copper conductor songle core cable in surface/recessed PVC conduit along with 1 No. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required.
Circuit/Sub-main wiring in PVC Conduit:- Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.
2x1.5 Sqmm + 1x1.5 sq.mm earth wire(for Single Separate 5A socket from nearest switch board)
2x2.5 Sqmm + 1x2.5 sqmm earth wire (for switch board circuit).
4 x 4 sq. mm + 2 x 4 sq. mm earth wire (Lighting DB)
4x6 Sq.mm + 2x6 Sq.mm earth wire. ( to be used as main for Light TPN DB.)
Telephone Wiring in Existing Conduit:- Supplying and drawing, following pair, 0.5 sq.mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed steel / PVC conduit as required.
TV cable in Existing Conduit:- Supplying and drawing, co-axial TV cable RG-6 grade copper conductor, PE insulated with PVC sheath in the existing surface/ recessed steel / PVC conduit as required.
S/F PVC Conduit: Supplying and fixing of following sizes of Rigid 2 mm thick PVC conduit alongwith the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required for TV and TEL out lets.
S/F Modular type Switch / Socket:- Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required. (to be used in switch board with sockets)
1.24.1 5/6 amps, one way switch
5/ 6 amps, two way switch
l5/ 16 amps, one way switch
5/6 amps, 3 pin socket outlet
S/F Modular type electronic fan regulator:- Supplying and fixing stepped (two module) type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.
S/F Modular blanking plate:- Supplying and fixing of the existing modular plate and switch box excluding modular plate etc, as required.
S/F Modular boxes, base and cover plate:-
Supplying and fixing following size /modules G.I. box along with modular base and cover plate for modular switches in recess etc. as required
6 module (78mm x 205mm x 50mm)
8/9 module (78mm x 230mm x 60mm)
l2 module (l35mm x 205mm x 60mm)
S/F light plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 5 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required.
S/F power plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.
S/F Ceiling Rose:- Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooden block including connection etc as required.
S/F Batten / Angle Holder:- Supplying and fixing batten / angle holder including connection etc as required.
Erection on incandescent light fitting :- Erection of wall bracket/ceiling fittings of all sizes and shapes containing upto two GLS amps per fitting, complete with all accessories including connection etc as required.
S/F Electonic Musical Call Bell:- Supplying and fixing electronic musical call bell suitable for D.C./A.C. single phase, 230Volts, complete etc as required.
ITC fluorescent fitting directly on surface:- Installation, testing and commissioning of Pre-wired fluorescent fitting /compact fluorescent fitting of all types, complete with all accessories and tube etc.directly on surace or ceiling/ wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper conductor, single core cable and earthing etc. as required.
ITC Ceiling Fan :- Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq. mm. FRPVC insulated,copper conductor,single core cable etc, as required.
ITC Exhaust Fan upto 450 mm sweep:- installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.
12 Way Double Door
S/F TP MCB DB: Supplying and fixing following way,three pole and neutral sheet MCB distribution board, 415 volts on surface/recess complete with tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections,phosphatised and powder painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR).
8 ways (4+24) Double Door. (horizontal type)
S/F 'C' series MCB:- Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.
6/32A Single Pole
40A DP MCB (To use as incomer for all SP MCB DB)
50/63A TPN (To use as incommer for all TPN D.B.)
P/F MV Danger Notice Plate:- Providing and fixing M.V. danger notice plate of 200mmX150mm, made of mild steel at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in the single red colour on front side as required.
Earthing with G.I. Earth plate 600mm x 600mm x 6mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal and salt as required).
Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal or cock and salt) complete etc. as required.
Providing and fixing 25 mm x 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc, as required.
Supplying and laying 25 mm x 5 mm G.I. strip at 0.50 meter below ground as strip earth electrode including connection/termination with G.I. nut, bolt, spring, washer etc, as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm)
Providing and fixing 25 mm x 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc as required.
S/L 25mm x 6mm G.I. earth strip in ground :- Providing and laying earth connection from earth electrode with 6 SWG dia G.I. wire in 15mm dia G.I. pipe from earth electrode, as required.
Providing and fixing 25mm x 5mm G.I. strip on surface or in recess for connection etc. as required.
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing etc. as required.
Providing and fixing 4.00mm dia copper wire on surface or in recess for loop earthing etc, as required.
P/F G.I. lightning conductor final - Providing and fixing of lightning conductor final, made of 25mm dia 300mm long, G.I. tube, having single prong at top, with 85mm dia 3mm thick G.I. base plate including holes etc. complete as required.
Reverting sweating and soldering of copper/ GI tape ( with other copper GI tape of the finial or any other metallic object) as required
P/F G.I. lightning conductor tape in horizontal run - Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)
P/F G.I. lightning conductor tape in vertical run - Provding and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)
P/F Testing joint G.I. lightning conductor - Providing and fixing testing joint, made of 20mm x 3mm thick G.I. strip, 125mm long, with 4 nos. of G.I. bolts, nuts, check nuts and spring washers etc. complete as required.
Earthing with G.I. Earth pipe 4.5 mtr long. 40mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal and salt as required).
Building Outer Light (90/100W LED) :- Supply of Street lighting luminaire aerodynamically shaped single piece pressure die-cast Aluminum luminaire with high power LEDs as light source and electronic driver (IP65), along with 90/100W LED Lamp, as Energy saving as per drawing prescribed reflector and heat resistant toughened flat glass cover, with 5ft long 40mm dia G.I. pipe with 3 Nos. of iron clamps , anchor nut bolts with double washers as per direction of E/I or consultant as per drawing prescribed reflector and heat resistant toughened flat glass cover (IP-65)Make:- Jaquare / Havells/ Wipro/Baja.
Supply, Installation, testing and commissioning of following, size ceiling fan 3 Blades confirming to IS : 374 : 2019 including wiring the down rods of standard length (up to 30cm) with 1.5 sq.mm. FR PVC insulated, copper wire suitable for 230V 50Hz, single phase supply etc. complete as required. 1200mm (48") BLDC 5star rating 32W Ceiling Fan
Supply, fitting and fixing of Special type bulk head fittings complete set with 9W LED. Make:- Jaquare / Havells/ Wipro/Baja.
15/16W LED type bulb :- Supply and fixing of 15 led bulb in existin Holder Fitting .Make:- Jaquare / Havells/ Wipro/Baja.
Supply of surface/ pendent mounted with suspenssion chain Batten type LED Tube light fitting with Housing & cover made up of CRCA sheet steel. Cover is fixed to the housing by means of 2 Nos. bolt with engineering plastic head along with 2 nos LED tube of 20/22W Each of luminous efficacy of efficacy >110 Lm/W. (Make :- Philips- / Havells / Equivallent in Bajaj / Wipro.).
Supply and Transportation of AC 230/250 Volts, 50Hz,300mm sweep Exahaust Fans including providing nuts- bolts, mounting frame and other required accessories etc. (For toilets) Make:- Bajaj /Crompton / Havells .
LT PANEL FOR Girl's HOSTEL BUILDING : (For G+2BUILDING) :- Supplying, designing, manufacturing, fitting, fixing, installation, testing and commissioning of LT Panel, fabricated out of 1.6mm thick (16 SWG) CRCA sheet steel IP:43, (dust and vermin proof) with reinforcement of suitable lifting arrangement effecting proper connection of all incomer and outgoing for all DBs , floor mounting type , fixed on base channel of 75mm x 75mm x 6mm, which will have incoming 3 phase power supply from Campus Sub-Station.
The sheet steel shall under go minimum of 7 tank treatment followed by finished powder coating of minimum 60 micron thickness and suitable for operation on 415V / 3 Ph / 50 Cy includes 415V electrolitic Al. bus bar with atleast 3 mm removable gland plate, cable glands including connection with outgoing feeders complete in all respect and should have bottom entry.
The panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 5/15A socket service outlet (single phase) and 1 no. CFL light with holder shall be provided in one of the compartments as service outlet in the panel. Panel shall be so designed as to have minimum 10% spare feeders/space. The complete panel shall be fuse less type, for control circuits 2A/6A MCB's to be used.
The panel shall be interlocked with switchgear in such a way that no door can be opened when the switch is in ON position.The switch gear shall have mechanical arrangement for interlock defeat.The design of panel shall be such as to offer maximun safety and easey of maintenance. The gap between live part of the Panel shall be minimum 35mm.
The MCCB's shall be Ics = 100% Icu, with rotary handle, spreader links & pad locking arrangement, with trip setting as per load requirement with short circuit & over current protection. The breaking capacity specified is Ics=Icu value. All MCCB's shall be of thermo magnetic category type.
AL. BUS BAR:- The panel includes 415V, 400A, 3Ph, 36KA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) G.I. Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. The electrolytic Aluminium bus bar of grade 63401 WP as per I:S 5082 of suitable length and insulated by heat shrinkable sleeves Red, yellow, Blue and Black as R Y B & N. The current density of bus bar shall be minimum 0.8 A / sq mm. All inter connections from main Bus Bar to individual MCCB shall be made with 4, 6 & 10 Sq mm FRLS PVC Cu. wire with 35A 4 studs (Brass) treminal block..
Each feeder shall have individual compartment with name plate with DB Nos., Floor No. and Block No.
Note:- Inspection of LT Panel shall be carried out by Engineering Incharge / Consultant (Eletcrical) at panel builder site and for that, all arragements shall be made by the suppilier on prior information to parrent department.
SLD along with the G.A. drawing of LT Panel will be submitted by the contractor to Engineering Incharge or to the Consultant for approval . The above SLD and G.A. Drawing of Main LT Panel must be based on approved SLD.
Panel Size - As per Drawing submitted.
Cost of Fabcrcation part of LT. Panel & busbar system, in CRCA Sheet Steel enclosure (IP-43) without any components. Name of Panel Builder :- SPC Electrotech Pvt. Ltd. / EAP / PM Control/TTS Systematix Private Ltd./ ADLAK. (A)
Make of MCCB - L&T D-Sine/ Legrand DPX³ / Schneider-NSX / Siemens - 3VL-or 3 VA
Make of MCB- C Series 10kA- Legrand/Schneider/ Siemens/ L&T.
INCOMER :-
400A FP MCCB (36kA) with adjustable thermomagnetic release type with S/C & O/L protection with extended front rotary handle and spreader links.
INDICATING FOR PANEL FOR LIFT MACHINE
CT 500/5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix
Phase indicating light shall be protected by 2 Amps SP MCB's for incomer.Make-L& T./ AE/ Schneider.
OUTGOING
100A/ FP/16kA MCCB with thermomagnetic release type with S/C & O/L protection with extended front rotary handle and spreader links -1No.
80A/FP/16kA MCCB with thermomagnetic release type with S/C & O/L protection with extended front rotary handle and spreader links. -8 Nos.
63A FP MCB C-Series.-4 Nos.
32A DP MCB C-Series.-2 Nos.
Total Cost of LT Panel for Girl's Hostel
FLOOR PANEL FOR Girl's HOSTEL BUILDING : :- Supplying, designing, manufacturing, fitting, fixing, installation, testing and commissioning of LT Panel, fabricated out of 1.6mm thick (16 SWG) CRCA sheet steel IP:43, (dust and vermin proof) with reinforcement of suitable lifting arrangement effecting proper connection of all incomer and outgoing for all DBs , floor mounting type , fixed on base channel of 75mm x 75mm x 6mm, which will have incoming 3 phase power supply from Campus Sub-Station.
The sheet steel shall under go minimum of 7 tank treatment followed by finished powder coating of minimum 60 micron thickness and suitable for operation on 415V / 3 Ph / 50 Cy includes 415V electrolitic Al. bus bar with atleast 3 mm removable gland plate, cable glands including connection with outgoing feeders complete in all respect and should have bottom entry.
The panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 5/15A socket service outlet (single phase) and 1 no. CFL light with holder shall be provided in one of the compartments as service outlet in the panel. Panel shall be so designed as to have minimum 10% spare feeders/space. The complete panel shall be fuse less type, for control circuits 2A/6A MCB's to be used.
The panel shall be interlocked with switchgear in such a way that no door can be opened when the switch is in ON position.The switch gear shall have mechanical arrangement for interlock defeat.The design of panel shall be such as to offer maximun safety and easey of maintenance. The gap between live part of the Panel shall be minimum 35mm.
The MCCB's shall be Ics = 100% Icu, with rotary handle, spreader links & pad locking arrangement, with trip setting as per load requirement with short circuit & over current protection. The breaking capacity specified is Ics=Icu value. All MCCB's shall be of thermo magnetic category type.
AL. BUS BAR:- The panel includes 415V, 100A, 3Ph, 16KA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) G.I. Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. The electrolytic Aluminium bus bar of grade 63401 WP as per I:S 5082 of suitable length and insulated by heat shrinkable sleeves Red, yellow, Blue and Black as R Y B & N. The current density of bus bar shall be minimum 0.8 A / sq mm. All inter connections from main Bus Bar to individual MCCB shall be made with 4, 6 & 10 Sq mm FRLS PVC Cu. wire with 35A 4 studs (Brass) treminal block..
Each feeder shall have individual compartment with name plate with DB Nos., Floor No. and Block No.
Note:- Inspection of LT Panel shall be carried out by Engineering Incharge / Consultant (Eletcrical) at panel builder site and for that, all arragements shall be made by the suppilier on prior information to parrent department.
SLD along with the G.A. drawing of LT Panel will be submitted by the contractor to Engineering Incharge or to the Consultant for approval . The above SLD and G.A. Drawing of Main LT Panel must be based on approved SLD.
Panel Size - As per Drawing submitted.
Cost of Fabcrcation part of LT. Panel & busbar system, in CRCA Sheet Steel enclosure (IP-43) without any components. Name of Panel Builder :- SPC Electrotech Pvt. Ltd. / EAP / PM Control/TTS Systematix Private Ltd./ ADLAK. (A)
Make of MCCB - L&T D-Sine/ Legrand DPX³ / Schneider-NSX / Siemens - 3VL-or 3 VA
Make of MCB- C Series 10kA- Legrand/Schneider/ Siemens/ L&T.
INCOMER :-
80A FP MCCB (16kA) with adjustable thermomagnetic release type with S/C & O/L protection with extended front rotary handle and spreader links.
INDICATING FOR PANEL FOR LIFT MACHINE
CT 100/5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix
Phase indicating light shall be protected by 2 Amps SP MCB's for incomer.Make-L& T./ AE/ Schneider.
OUTGOING
63A FP MCB C-Series.-6 Nos.
32A DP MCB C-Series.-2 Nos.
Total Cost of LT Panel for Girl's Hostel
Providing and fixing of PVC/XLPE indulated PVC sheathed heavy duty , aluminium armoured cable of grade 1.1KV as per IS 1554 (Part-1), etc. as required. Make:- Havells / Finolex / Polycab/KEI. 3.5 Core 35 Sq.mm. XLPE Al. Ar. Cable 1.1kV.
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 1 run of Cable
1.1 KV Cable End Termination:-Supplying and making indoor cable end termination with brass double compression gland and aluminium lugs for following size of PVC insulated XLPE Al. Ar. Cable of 1.1 KV grade as required. 3.5 Core 35 Sq. mm. (32mm)
Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc. as required 100 mm dia
Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. E.W.C With "S" trap (b)10 lit. low level P.V.C. cistern
Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. of parry hindustan or any other ISS approved make with 100mm HCI p trap 15 litres CI pull and let go flushing cistern of names or other ISS equivalent make complete with all fittings CI or C C bracket 32mm alkethene / PVC telescopic flush pipe about 2m long with one brass coupling and clamps GI chain and pull including supplying and fixing a pair of vitreous white glazed earthenware footrest to be fixed in floor 15mm CI body brass spindle stop cock of weight not less than 50 grames 15mm PVC connection pipe 450mm long and coat of red oxide primer etc all complete as per specification and direction of E/I.
(A) 580 mm long
(b) with 12.5 litre low level PVC cistern
supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or hindustan or any other I.S.S approved make supported on painted C.I OR R.S bracket 32mm C.I brass waste 15mm dia C.I body brass spindle stop cock of approved quality of weight not less than 350 grames, 32mm PVC wate pipe 750mm long with brass coupling with one end and making plumber joints etc.all complete as per specification and direction of E/I.
Providing & fixing stainless steel jali (grating) with hole for waste pipe for floor / nahani trap.
100 mm dia. Weight not less than 100 gms.
Supplying, fitting and fixing gun metal full way valve of approved quality all complete as per specifcation and direction of E/I.
15mm dia.
20mm dia.
25mm dia
32mm dia
Providing and fixing brass stop cock of approved quality all complete as per specification and direction of E/I. … 15mm dia.
Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E/I.
Pillar cock (long neck)
Bib cock - long thread
Angular stop cock L.T.
Glass shelf
Flush valve complete with 32mm size control cock & flange
32mm dia. PVC waste pipe 750mm long with cushion
Providing Solvent cement
Supplying, fitting and fixing Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror. 600 X 450mm
Supplying, fitting and fixing C.P. brass towel rail 20mm X 600mm with bracket container
Supplying, fitting and fixing C.P. brass soap dish container medium quality with screw and hinges etc.
Providing and fixing 15mm dia and 45cm long PVC connection pipe with heavy quality brass coupling at both ends etc all complete as per specification and direction of engineer in charge
Providing and fixing PTMT extension nipple 15mm size with 12" BSP thread 70mm length and 30mm breadth and weighing not less than 32gms of approved make
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e fixing the pipe with clamps at 1Mtr. Spacing. This includes jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. Concealed work including cutting chases and making good the walls etc.
20mm nominal bore
25mm nominal bore
32mm nominal bore
External work - 40mm nominal bore
Providing & fixing on wall face unplasticised - Rigid P.V.C. pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia
Providing and fixing on wall face unplaqsticised- PVC moulded fitting/ accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A,including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.
Single Tee with door
110 mm bend
Supplying and fixing PVC fittings of approved make confirming to IS : 1729 including supplying nails and bobbins, fixing solutions including earth work or masonary work cutting and remaking and providilding as the case may be all complete as per specification and direction of E/I.
PVC cowl - 100mm dia.
Floor trap - 100mm dia.
Ring rubber
Door piece
HYDT: Cost of Drilling 200 mm x 165 mm x 125 meter deep bore well in all kinds of soil and rock in Rural) area for Installation of pump set with Hydraulic DTH Ring machine, all complete including supplying all materials, tools, drilling, rig, Air Compressor and Equipments, as well as fuel, lubricants and cost of Transportation of Rig Machine and other Vehicle up to site.
From 0.0M to 50.0 M
From 51 M to 125.00 M
Supplying all tools, tackles & lowering of 200 mm dia MS ERW casing pipe of 6 mm wall thickness including welding charges, cost of Pipe etc. including all taxes, VAT, Excise duty, Fright charges with inspection charges etc. as applicable, etc. all complete Jobs.
Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tube well, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.
Supplying all materials, labours, tools & equipments for fitting & fixing 200 mm dia M.S.Cap over Casing Pipe including all taxes, VAT, Excise duty, Fright charges with inspection charges etc. as applicable, etc. all complite Jobs.
Supplying 100 mm dia Submersible Pump Set Conforming to IS : 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and Polypropylene / Noryl impeller. Motor suitable for working on 415V+10%, 3PH, 50Hz, A.C. Supply with cable guard, thurst carbon / fiber bearing to with stand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall be suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single / double run shall be provided with each pump. Submersible Pump set 100 mm dia ( with Polypropylene / Noryl impeller ) up to 20 stages. 2 HP
Supplying installing and comissioning of pannel board suitable for motor pump set as mentioned in the item no 5 , having voltmeter, ammeter, phase indicating lamp, starter, main switch fuse inter connection in the panel board including cost of wire etc. all complete job as per specifcation and direction of E/i
Cosat of pvc insulated copper sunmersible cable (2.5 sq. mm X3 core ) of finolex or equivalent make including lowering and making water proofing joints including all taxes and transportation to work site etc as per specificationand direction E/I
G.I.FITTINGS ( CONFORMING TO I.S. - 1979 (K) G.I. PIPES ( TATA MARK ) OR EQUIVALENT 40 mm dia
FIRE PUMP ROOM EQUIPMENT
Supply, Erection, Testing and Commissioning of electric driven, horizontal type, single/multistage, end suction type, centrifugal pump of cast iron body, C.I impallers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motors suiitable for operation on 3 phase, 415 volts 50 Hz AC supply having flow rate of min 450 LPM at 35 MWC complete in all respect.
Control Panel for Fire pumps
Fabricating & Supply, installing, testing and commissioning of compartmentalized common control panel for Electrical motor driven pumps. (Main Pump , Jockey Pump & Diesel Engine Pump)
1100 V GRADE POWER / CONTROL CABLES
Supplying, laying, testing & commissioning of FRLS,PVC outer sheath, steel armored, copper conductor, 1100v grade power cables with glands etc.The cables shall be laid in tray / in trenches/on walls/ floor etc. as required.
CABLE TRAY
Supplying and fixing of perforated G.I.sheet cable tray with necessary angle iron suspension supports, anchor fasteners etc. complete. Maximum height of suspension shall not exceed 500 mm.Size of the tray shall be suitable for laying the above mentioned cables.
G.I. Earth strips of 50mm x 6mm thick, strip shall be run on floor / ceiling / walls, from the equipment to the nearest Earth pit with with necessary accessories as required. ( Erath pit shall be executed by other agencies).
150 mm nominal dia
100 mm nominal dia
80 mm nominal dia
100mm nominal dia
Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS: 5312(PN 1.6) swing check type with required flanges, nuts, bolts and gaskets etc. complete.
100 mm nominal dia
80 mm nominal dia
Supplying, Installing, testing and commissioning CI butterfly valves as per BS 5155 (PN 1.6) slim seal standard lever operated type with required flanges, nuts, bolts etc. complete.
100mm nominal dia
80mm nominal dia
Supply, Erection, Testing and commissioning of C.I.Gate valves as per IS: 14846 (PN 1.0 Rating, for suction side of the pumps) and Non rising spindle type with flanges,bolts, nuts, washers, gaskets etc.
100mm nominal dia
Supply, Erection, Testing and commissioning of Suction Strainer with flanges, bolts, nuts, washers, gaskets etc.
100mm nominal dia
Supply and installation of Pressure switches of suitable range for pump sets with Ball valves, Fittings like unions / collars / reducers etc.
Supply and installation of Pressure gauges of suitable range for pump sets with Ball valves, siphon, Fittings like unions / collars / reducers etc.
HYDRANT SYSTEM
Supplying, installing, testing and commissioning of M.S. Pipes confirming to IS 1239/3589, Heavy grade with suitable type of supports, malleable specials such as Reducers, Tees, elbows, flanges. Including cutting,Welding as per drawings. The rate quoted should be included with anticorrosive treatment with 4 mm thick "PYPKOTE" polymer corrosion resistant tape as per IS 10221, overlap shall be 15mm minimum.
100mm nominal dia
80mm nominal dia
Supply, Erection, Testing and commissioning of C.I.Gate valves as per IS: 14846 (PN 1.6 Rating) and Non rising spindle type with flanges,bolts, nuts, washers, gaskets etc.
100mm nominal dia
Supplying, Installation,Testing and commissioning of Hydrant valve comprising of the following in the Fire duct;
Single headed hydrant valve as per IS 5290, made of gunmetal/stainless steel with 63 mm dia instantaneous outlet of 80 mm dia fanged inlet ,Blank caps , chain and hand wheels etc complete.
15 M long, 63mm dia RRL hose with instantaneous couplings and Hoses shall be stored in side the hose cabinet.
1 no. Gun metal/ stainless steel short branch pipe with nozzle.
Supplying and fixing approved make 25mm dia. Air release safety valve with unions,ball valve etc. complete.
Providing and fixing swinging, wall mounting type First Aid Hose Reel of approved quality and made from compresed steel sheet with dust cover, cast iron brackets including 30 m long, 19 mm nominal bore, high presure braided rubber hose as per IS:444 Type hose guide, PVC shut off nozzle with 6 mm outlet and 25 mm nominal bore gun metal inlet valve, bolts, nuts rubber insetion etc. painted in Fire red colour including cutting and making good the walls wherver required
Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valves with fittings of screwed end type.
30 mm dia.
40mm dia.
FIRE EXTINGUISHERS
Supplying, installing and commissioning Portable Fire extinguishers of following type & capacity.
Carbon-di- oxide type fire extinguisher of 4.5 kgs. Capacity, CO2 gas filled in brand new seamless cylinder with powder coated finish, made out of Manganese steel, with wheel type valve, discharge nozzle, bend & horn,wall mounting bracket etc. complete, confirming to IS: 15683
Dry chemical powder type fire extinguisher of 5 / 6 Kgs. Capacity, with initial filling in brand new cylinder with powder coated finish, fitted with Gun metal union,high pressure CO2 gas cartridge, discharge hose, wall mounting bracket etc. complete, confirming to IS:15683
Fire Alarm System
Supplying, installing and commissioning of Manual call point with . cabinet of suitable size with mounting supports etc. complete.
Supplying, installing and commissioning of Electronic Hooter cum sounder with M.S. cabinet of suitable size with mounting supports etc. complete.
Supplying, installing and commissioning of 2 x 1.5 Core Cable with conduit wiring
Student Room Furniture
Bed (Metal Bed 1900 mm x 900 mm )
Study Table (Table 900 mm x 600 mm )
Chair (Without Armrest)
Reception Furniture
Table (Table 900 mm x 600 mm )
Chair (Without Armrest)
Warden Office
Ofiice Table (900mm x 600 mm with Lockable drawers)
Ofiice Chair (Revolving Chair with Knee tilt mechanism)
Visitor Chair (Chair Non-revolving and non-tilting chair with armrest )
Three seater Sofa (Three Seater Tubular Steel Sofa Set Thick Chrome Plated)
Drinking Water Cooler System
Drinking Water Cooler (Storage Type Water Cooler 120 LPH Cooling Capacity )
Water Purifier (Filtration capacity (In LPH):20 and above)
Dinning Furniture
Dinning Table with Chair (Stainless Steel Rectangular Dining Table with Round fixed Chair )
Staff Room Furniture
Bed (Metal Bed 1900 mm x 900 mm )
Providing & Fixing 8 Passanger Lift in Building of 5 Floor (G+4)- of 8 Passanger (5 Floor, 5 Stop) with all complete specification and direction of E/I.
Passanger Lift ( 8 person, Speed 1.0 m/s )
Hostel Block (G+4)
Carriage Of Materials
Sand 10 KM
Aggregate 22 KM
Brick 8 KM
Stone Metal (22 km)
Add GST 18 %
Add Labour cess 1%
M/S MANOJ KUMAR PANDEY (BID ID -689762)
stage.html
html • 0.03 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.39 MB
41SBD.pdf
Tender Documents • 9.74 MB
BOQ_143300.xls
BOQ • 0.46 MB
Download all tender documents and submit your bid