SPECIAL REPAIRS TO BLDG NO WL 08 (10 x ORs MARRIED ACCOMMODATION UNDER AGE (I) KANNUR

Amount

Dismantling of single layer Mangalore pattern or similar tiles in roofing complete all as specified and as directed.

Dismantling of battens spaced exceeding 15 cm center to center for tiles, shingles etc. of any size including tilting fillets complete all as specified and as directed.

Dismantling of timber scantlings 40 sqcm and over in section in any position, unframed work complete all as specified and as directed.

M&L for second class Hard Wood scantlings, clean sawn as in rafters, purlins etc; framed and fixed as directed by Engineer-in-charge without finish complete all as specified and as directed.

All as in item No. 4 above but for except timber complete all as specified and as directed.

M&L for Mild steel work rectangular/ tubular trusses as in purlins etc including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS specifications complete all as specified and as directed.

S&F 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel of any colour, having tensile strength of 550 MPa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based plain steel of any colour, having tensile strength of 550 MPa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F PVC (SWR) pipe 200 mm bore as in half round vally gutters including suitable drop ends/stop end and fixing with MS/PVC clamps suitable for steel sheet roofing complete all as specified and as directed

S&F PVC (SWR) down take pipe 75mm bore single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and as directed.

M&L for preparing new or previously un treated wood and wood based surfaces of any description over 10 cm in width or girth and applying two coats of creosote oil complete all as specified and as directed.

M&L for preparing old wood and wood based surfaces of any description over 10 cm in width or girth and applying one coats of creosote oil complete all as specified and as directed.

M&L for preparing new or previously un treated steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and as directed.

S&F true horizontal level 600 mm x 600 mm false celling snap grid frame manufactured by Armstrong world industries using hot dipped galvanized steel section, exposed surface with pre coated capping main tee of size 24 x 32 mm having 0.27mm geuge at every 1200mm cenre to centre maximum and coary stiched cross tee of size 24 x 27mm, having 0.27mm gauge at every 600mm c/c and sub cross tee of size 24 x 27mm, having 0.25mm gauge at 122 c/c, are wall angle size of 19 x 19mm having 0.35mm gauge fixed to the poiphery of the wall. The above god is suspended at every 1200 c/c in both directions using 2mm thick pre straightered GI wire complete all as specified and directed by Engr-in-Charge.

S&F 4 mm thick non asbestos fiber cement building board with pre painted having textured surface finished fixed of laid/inserted to GI snap grid frame work with screws all as specified and directed by Engr-in-Charge.

Dismantling water tanks of capacity exc 250 but n exc 500 litres and removing to store complete all as directed.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top)of capacity 500 litres hoisted and fixed in position all as specified in SSR Part I.

S&F Ball brass valves, 25mm bore high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed

Taking down 15mm bore GI tubing and connections including removal to store complete all as specified and as directed.

All as per item No 19 here in before but 20mm bore

All as per item No 19 here in before but 25mm bore

Cutting chases on wall of width 10 cm, depth 35mm for concealing PVC conduct of 15/20/25mm dia, in stone, concrete block or slab, walls etc., with and including making good, smooth finishing to match the existing colour of the wall complete all as specified and as directed.

S&F in repairs angle cocks cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch of butterfly handle screwed both ends for iron pipe of 15mm bore complete all as specified and as directed.

S&F in repairs stop valves, cast copper alloy, screwed down, high pressure, with crutch of butterfly handle screwed both ends for iron pipe of 20mm bore complete all as specified and as directed.

S&F in repairs stop valves, cast copper alloy, screwed down, high pressure, with crutch of butterfly handle screwed both ends for iron pipe of 25mm bore complete all as specified and as directed.

M&L for 15mm bore unplastisized PVC pipe of pressure rating 10kg/cm2 fixed on walls ceilings or on floor complete all as specified and as directed.

All as per item No 55 here in before but 20mm bore

All as per item No 55 here in before but 25mm bore

Demolition of brick or stone/ boulder masonry built in cement mortar complete all as specified and as directed.

Demolition of Reinforced cement concrete of any description and any position complete all as specified and as directed.

M&L for RCC 1:2:4 Type B1, using 20 mm graded stone aggregate as in slabs supported on walls, beams in floors, roofs, landings, deck slabs, shelves etc., complete all as specified and as directed.

M&L for formwork to soffits of slabs, floor slabs, landings, shelves and similar items not exceeding 200mm thick finished rough, complete all as specified and as directed.

M&L for formwork to edges of concrete flats, floor and roof slabs, landings, shelves and similar works exceeding 5cm but not exceeding 10cm wide finished rough, complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L walling of laterite stone walls uncoursed, well bonded bedded and solidly hearted built in cement mortar 1:6 complete all as specified and as directed.

All as in item No.35 above, but except stones (old serviceable stone reused in the work).

M&L for granite (of any type) slab as in work table, 18 to 20mm thick matching cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment of match to shade of granite stone including grinding and polishing, complete all as specified and directed.

M&L for granite (of any type) slab as in work table wall lining, 18 to 20mm thick matching cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment of match to shade of granite stone including grinding and polishing, complete all as specified and directed.

Labour only for rounding of edges of stone slab or mouldings of granite edges and nosing by chamfered or rounded all as specified and as directed.

Taking down cement or cement line plaster on brick/stone walls including racking out joints hacking for key scrubbing down with water etc and removing rubbish complete all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on stone masonry surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1:4 mixed with water proofing compound, on concrete surface of roof slab finished even and smooth without using extra cement complete all as specified and as directed. Note:- Cost of water proofing compound shall be measured and paid separately.

Supply only liquid integral water proofing compound (200ml per cement bag consist of 50kg) complete all as specified and as directed.

M&L for APP modified prefabricated polymeric membrane 4.0 mm thick and weighing not less than 4.0 kg/sqm reinforced with non woven polyester matt black finished weighing not less than 160 gm /sqm having softening point not less than 140 degree Celsius longitudinal tensile strength not less than 800N/Sqcm, tearing strength of 180Nm, side lap & end lap 10 cm, by torch application of membrane, including and over a compatible primer @ 0.2 Kg/Sqm and finishing with solar reflective bituminous aluminium paint applied @ 0.10 Kg/Sqm complete all as specified and directed.

Taking down chowkat or frames not exceeding 1.5 sqm each with shutters (without taking off shutters from frame) complete all as specified and as directed.

Taking down chowkat or frames exceeding 1.5 sqm but not exceeding 4 sqm each with shutters (without taking off shutters from frame) complete all as specified and as directed.

M&L for Solid PVC door frame of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, as per specification and drawings shown in SSR complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain coloured PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rail and bottom rail, paneling of plain colour of PVC sheet fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement etc. Details as per specification and drawing shown in SSR complete all as specified and as directed.

S&F powder coated aluminium frames for doors, windows, ventilators with one or more rebates including joining cleats for fixing etc complete all as specified and as directed.

S&F powder coated sliding/ side hung type aluminum window and ventilator shutters (as directed) without sash bars, using aluminium section weighing exceeding 0.55kg/m including necessary joining cleat, glazing clips, rubber neoprene packing, suitable handle, side lock for shutters, aluminium snap beading, screws etc., complete all as specified and as directed.

S&F 3mm thick Figured/frosted glass, not exceeding 0.50 sqm in each pane and glazing with aluminium snap beads on aluminium windows/wooden beading at wooden windows complete all as specified and as directed.

S&F 150 mm size anodised aluminium barrel tower bolts of extruded section complete all as specified and as directed.

S&F 100mm size stainless steel butt hinges medium weight complete all as specified and as directed.

S&F 150mm size anodised aluminium alloy handle fabricated type complete all as specified and as directed.

S&F in repairs vitreous china squatting pan, Orissa pattern, size 580 x 440mm, white with integrated foot rest in lime concrete bedding including taking out the existing unserviceable pan complete all as specified and as directed.

S&F in repairs PVC low level flushing cistern, 10 Ltr capacity valve less, syphonic action type, white, with inlet, ball valve, float and handle including all fittings and brackets bends flush pipe etc complete all as specified and as directed.

S&F in repairs vitreous china wash hand basin of size 550 x 400 mm, white, flat back, with brackets and including cutting for pinning in ends of brackets, taking out the existing unserviceable WHB complete all as specified and as directed.

S&F in repairs pillar taps, cast copper alloy with capstan heads, chromium plated, fancy type, long screwed shanks and fly nuts, screwed for iron pipe 15mm bore complete all as specified and as directed.

S&F in repairs 32mm dia waste fittings, brass, chromium plated for wash hand basin with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and as directed.

Taking up or down PVC tubing and connecting including cleaning for removing to store of sizes 32/50mm bore all as directed.

S&F 32mm bore Low density Polyethylene pipe(LDPE) of pressure rating 6kgf/cm2 fixed complete to walls, floors or in ceilings etc complete all as specified and as directed.

S&F in repairs PVC connection 600mm long (high density) 15mm size PTMT nuts/sockets both ends with rubber washer complete all as specified and as directed.

S&F in repairs 15mm bore bib tap cast copper alloy, chromium plated, fancy type, with butterfly handle, screwed down for iron pipe complete all as specified and as directed.

S&F in repairs 125mm size, Shower rose cast copper alloy, chromium plated, for iron pipe complete all as specified and as directed.

S&F in repairs 195mm long, Shower arm with 45 degree bend with flange of PTMT, any colour, for iron pipe of 15mm bore complete all as specified and as directed.

S&F in repairs tubular towel rail, 20mm dia, D type, 60 cm long between flanges, brass chromium plated complete all as specified and as directed.

Dismantling drain pipes (Cast iron/ RCC) set in cement mortar internal dia of pipes up to 100mm and removing debris outside MD land complete all as specified and as directed.

S&F PVC (SWR) pipe 110mm bore, single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and as directed.

S&F PVC (SWR) pipe 110mm bore, single socketed, in any length with rubber ring joints, laid in floors or in trenches complete all as specified and as directed.

S&F PVC (SWR) pipe 75mm bore, single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and as directed.

S&F PVC (SWR) pipe 75mm bore, single socketed, in any length with rubber ring joints, laid in floors or in trenches complete all as specified and as directed.

S&F PVC (SWR) vent cowl for 110mm bore pipe, complete all as specified and as directed.

S&F PVC (SWR) bends of any radius, 75 mm bore, complete all as specified and as directed.

S&F PVC (SWR) bends of any radius with access door, 75 mm bore, complete all as specified and as directed.

S&F PVC (SWR) bends of any radius, 110 mm bore, complete all as specified and as directed.

S&F PVC (SWR) junction single T, equal or un equal, 110 mm bore, complete all as specified and as directed.

S&F in repair 75mm PVC floor trap plain with grating including jointing with solvent cement complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc 15cm thickness (below or above GL) complete all as specified and as directed.

M&L for 25mm thick cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in flooring/ concrete padding complete all as specified and as directed.

M&L for 20mm thick screed bed or bedding layer in cement mortar 1:6, for laying floor finishes complete all as specified and as directed.

M&L for coloured non skid ceramic tiles 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match, as in floors etc., complete all as specified and as directed.

M&L for rendering 10mm thick in cement mortar 1:4 on stone masonry surfaces, as backing coat to receive dado/skirting complete all as specified and as directed.

M&L for coloured glazed ceramic tiles 300x200x7mm, set and jointed in neat cement slurry and pointed in white or coloured cement to match on vertical surfaces of wall such as skirting dado etc. complete all as specified and as directed.

M&L for preparation of new plastered surfaces of wall and applying three coat of white wash complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coat of white wash complete all as specified and as directed.

M&L for preparation of old plastered/unplestered surfaces of wall and applying two coats of white wash complete all as specified and as directed.

Taking down unserviceable fluorescent tube light fittings and S&F Decorative ultra slim linear LED light fittings with extruded AI, heat sink, environmental friendly, energy efficient ready to use pack of E-LITE LED of 20 W LED 6000K, electrically connecting up complete all as specified and as directed. Model LHEWEBP7INIW020 of Havells or techno commercially equitant in bajaj /crompton greaves

Taking down unserviceable tube light fitting and S&F decorative ultra slim linear LED light fittings with extruded Aluminium, heat sink, environmental friendly, energy efficient ready to use pack of E-LITE LED OF 10W LED 6500K and electrically connecting up complete all as specified and as directed. Model LHEXBYPNIN1W010 of Havells or techno commercially equitant.

S&F stop cock cast copper alloy chromium plated with long shank and cup (concealed type) high pressure with capstan heads handle, screwed both ends for 15mm dia pipe or unions complete all as specified and as directed.

M&L preparation of old wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

LEKSHMI ENGINEERS

Safarulla padikkal

T.P.SUNIL KUMAR

Anaswara Constructions

Sreema Enterprises