MLA-SDF-Construction of Nursing Station and Waiting area for Dialysis Block in Taluk Head Quarters Hospital, Parassala-Work-General Civil Work

Estimate

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

4.1.2:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

50.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

OD281746/2025-2026:Providing & fixing Poly carbonate solid type sheet 4 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling/ self tapping screw of size ( 5.5x55mm) with EPDM seal complete upto any pitch in horizontal /vertical / curved surface, but excluding the cost of purlins, rafters, trusses, and including cutting to size and shapes where ever required.

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

OD281789/2025-2026:Supplying and installing SS hand washing sink with stand made out of 1.5mm 304 Grade Stainless Steel sheet, SS round pipe legs attached with adjustable nylon bushes. Size 45 x 45 x 45, 75 cm height.

OD281790/2025-2026:Supplying and installing SS hand washing sink with stand made out of 1.5mm 304 Grade Stainless Steel sheet, SS round pipe legs attached with adjustable nylon bushes. Size 165 x 60 x 45, 75 cm height.

OD281791/2025-2026:Supplying and installing SS hand washing sink with stand made out of 1.5mm 304 Grade Stainless Steel sheet, SS round pipe legs attached with adjustable nylon bushes. Size 200 x 60 x 45, 75 cm height.

OD281794/2025-2026:Providing and fixing required Stainless Steel Push pull connector of grade AISI 304 and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. 22.22 mm outer dia x 20 mm nominal dia threaded.

OD281795/2025-2026:Providing and fixing elbow action bib cock of approved quality :20 mm nominal bore

21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

OD282266/2025-2026:Providing and fixing 4 mm thick ACP in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.

Please Enable Macros to View BoQ information