AS AS AND SPECIAL REPAIRS TO VINTAGE (20X20) TILES ON SECOND AND FOURTH FLOOR AT MWC AND PROVN OF SLIDING DOOR WITH PEDESTRIAN GATE AT SUBSTATION NEAR BLDG NO. P-40 AT IN CIRCARS UNDER GE (NB) VISAKHAPATNAM

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposal of debris and rubbish to outside MD land complete all as specified and directed.

M & L for Virified designed, dark shade/double charged/ ultracharged coloured, Ceramic tiles, 7 to 8 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. and set & jointed in neat cement slurry and 3mm wide joints shall be maintained with spacers which is to be filled with epoxy grout using masking tape and the masking tape is to removed after filling the epoxy groutand including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M & L for Vitrified, designed, dark shade/double charged/ ultracharged coloured, tiles, 7 to 8 mm thick, (square/rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm as in vertical surfaces such as skirting, dado, etc and set & jointed in neat cement slurry and 3mm wide joints shall be maintained with spacers which is to be filled with epoxy grout using masking tape and the masking tape is to removed after filling the epoxy grout and including 10 mm thick bedding in cement mortar 1:4 and necessary cutting of tiles complete all as specified and directed.

M & L for Complete removal of existing treatment from walls etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7/9 inch to make the surfaces free from dust, loose paints etc by skilled labour complete all as specified and directed.

M & L for applying one coat of acrylic water based interior grade primer @ 0.8 ltr (undiluted)/ 10 Sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application with flow speed of min 1 ltr per minute having a pressure of 3300 PSI and allow 6-8 hrs to dry the surfaces for painting of susequent coat complete all as specified and directed.

M & L for preparation of new surfaces of wall/ceiling and applying two coats of oil bound distemper by using fully automatic Airless spray tenchnology machine with max pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr, the spray machine should be from reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and acccessories for applying distemper in hard to reach areas and penetration of distemper on the surface complete all as specified and directed. (Note: Sanding of surfaces shall be done by mechanical sander with 1500-2700 rpm with internal dust extraction system for clean environment certified by the Paint manufacturer)

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, trenches for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Excavating in trenches not exc. 1.5 metre wide and exc. 1.5 metre & not exc. 3 metre depth (beyond the first 1.5 metre) for foundation of poles etc and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for use & waste Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams and similar work, vertical or to batter complete all as specified and directed.

M & L for use & waste Formwork to sides of pillars, posts, struts, piers, columns and stanchions for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for Reinforced Cement Concrete M-30 (Design Mix) (using 20 mm graded stone aggregate) as in foundations including rafts, footings, beams and mass concrete, etc complete all as specified and directed. (Note" Reinforcement will be measured and paid seperately)

M & L for Reinforced Cement Concrete M-30 (Design Mix) (using 20 mm graded stone aggregate) as in columns, pillars, posts and struts complete all as specified and directed. (Note : Reinforcement will be measured & paid seperately)

S & F high strength corrosion resistant TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

S & F high strength corrosion resistantMild steel TMT bars 5mm dia and over upto and including 10mm dia in strirrups, spacers and binders spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and fair without using extra cement complete all as specified and directed.

M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M & L for Sand filling under floors or in foundations including spreading, levelling, watering and consolidation complete all as specified and directed.

M & L for Mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe 410-W (Gde- E- 250) quality- A complete all as specified and directed.

M & L for Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel') complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zine chrome primer complete all as specified and directed.

RAGHU RAMA PANDA

HARISH CONSTRUCTION

M B CONSTRUCTIONS

S RAMAKRISHNA RAJU

M/S REAL POWER SYSTEMS

SRI VIJAYA LAKSHMI ENTERPRISES

SRI JAYANTH ASSOCIATES

VISWAS ENGINEERING WORKS

bhavani constructions

P NARAYANA RAO