GENERAL AMC 2023 24 Maintenance of various LI Schemes in Aluva area under Electrical L I Section Aluva General Electrical Work

Amount

Lifting

OD205964/2023-2024: Lifting the 125 HP motor after disconnecting the wire connection, decoupling the pump, detaching from the base plate, starters, TP switches etc. and placing them conveniently on the platform.

OD205965/2023-2024: Lifting the 100 HP motor after disconnecting the wire connection, decoupling the pump, detaching from the base plate, starters, TP switches etc. and placing them conveniently on the platform.

OD205966/2023-2024: Lifting the 75 HP motor after disconnecting the wire connection, decoupling the pump, detaching from the base plate, starters, TP switches etc. and placing them conveniently on the platform.

OD205967/2023-2024: Lifting the 60 HP motor after disconnecting the wire connection, decoupling the pump, detaching from the base plate, starters, TP switches etc. and placing them conveniently on the platform.

OD205968/2023-2024: Lifting the 45 HP motor after disconnecting the wire connection, decoupling the pump, detaching from the base plate, starters, TP switches etc. and placing them conveniently on the platform.

OD205969/2023-2024: Lifting the 40 HP motor after disconnecting the wire connection, decoupling the pump, detaching from the base plate, starters, TP switches etc. and placing them conveniently on the platform.

OD205970/2023-2024: Lifting the 25 HP motor after disconnecting the wire connection, decoupling the pump, detaching from the base plate, starters, TP switches etc. and placing them conveniently on the platform.

OD205971/2023-2024: Lifting the 5 HP motor after disconnecting the wire connection, decoupling the pump, detaching from the base plate, starters, TP switches etc. and placing them conveniently on the platform.

Lowering/Refitting

OD205972/2023-2024:Lowering down and erecting 125 HP motor, starter and other electrical accessories,( Accessories when necessary ) and erecting the motor on the base plate coupling with pump, erecting the starter regulator TP switch etc in position giving connections checking correct alignment and trial run on full load

OD205973/2023-2024:Lowering down and erecting 100 HP motor, starter and other electrical accessories,( Accessories when necessary ) and erecting the motor on the base plate coupling with pump, erecting the starter regulator TP switch etc in position giving connections checking correct alignment and trial run on full load

OD205974/2023-2024:Lowering down and erecting 75 HP motor, starter and other electrical accessories,( Accessories when necessary ) and erecting the motor on the base plate coupling with pump, erecting the starter regulator TP switch etc in position giving connections checking correct alignment and trial run on full load

OD205975/2023-2024:Lowering down and erecting 60 HP motor, starter and other electrical accessories,( Accessories when necessary ) and erecting the motor on the base plate coupling with pump, erecting the starter regulator TP switch etc in position giving connections checking correct alignment and trial run on full load

OD205976/2023-2024:Lowering down and erecting 45 HP motor, starter and other electrical accessories,( Accessories when necessary ) and erecting the motor on the base plate coupling with pump, erecting the starter regulator TP switch etc in position giving connections checking correct alignment and trial run on full load

OD205977/2023-2024:Lowering down and erecting 40 HP motor, starter and other electrical accessories,( Accessories when necessary ) and erecting the motor on the base plate coupling with pump, erecting the starter regulator TP switch etc in position giving connections checking correct alignment and trial run on full load

OD205978/2023-2024:Lowering down and erecting 25 HP motor, starter and other electrical accessories,( Accessories when necessary ) and erecting the motor on the base plate coupling with pump, erecting the starter regulator TP switch etc in position giving connections checking correct alignment and trial run on full load

OD205979/2023-2024: Lowering down and erecting 5HP motor and erecting the motor on the base plate coupling with pump in position giving connections checking correct alignment and trial run on full load

Accessories Supply and supply and Renewal of MS pipe at Avanamcode 1A

OD216692/2023-2024:Dismantling the existing MS Suction pipe, bend of size 400 mm piece by piece after providing scaffolding supports and stacking at the yard

OD241684/2023-2024:Supply, conveying, erecting, testing and commissioning the 400 mm dia MS pipe in suction/ delivery side having sheet minimum thickness 6.35 mm and cutting in to required length, facing the cutting edges, painting two coats of synthetic best quality enamel paint over a coats red oxide primer, including conveyance charges to pump house and labour charges for loading, unloading, etc

OD241837/2023-2024:Supply and providing the rough cut flange ring joint 15 mm depth for 400 mm MS pipe after facing the cutting edges of flange rings neatly and set out the flange rings in correct position to both vertical and horizontal planes and welding in two rows accurately, painting two coats of synthetic best quality enamel paint over a coats red oxide primer including providing necessary nuts and bolts , rubber packing grease etc , all labour charges for lifting and holding of pipes as per the necessity of welder at site.

OD241899/2023-2024:Supply, fabrication, conveyance, fixing, testing and commissioning of 400 mm size MS pipe short bend with 15 mm thick flanges at both end, fabricated from 400 mm MS pipe having 6.35 mm sheet thickness, with length not less than 0.5meter, painting two coats of synthetic enamel paint over a coat of red oxide primer and fixing in position using fresh rubber packing, gaskit packing, bolts and nuts etc. in correct alignment and leak proof condition.

OD241613/2023-2024:Dismantling the existing MS delivery pipe of size 300mm piece by piece after providing scaffolding supports, with out further damages including MS bent , accessories etc. and stacking at the yard

OD241703/2023-2024:Supply, conveying, erecting, testing and commissioning the 300 mm dia MS pipe in suction/ delivery side having sheet minimum thickness 6.35 mm and cutting in to required length, facing the cutting edges, painting two coats of synthetic best quality enamel paint over a coats red oxide primer, including conveyance charges to pump house and labour charges for loading, unloading, etc

OD241836/2023-2024:Supply and providing the rough cut flange ring joint 15 mm depth for 300 mm MS pipe after facing the cutting edges of flange rings neatly and set out the flange rings in correct position to both vertical and horizontal planes and welding in two rows accurately, painting two coats of synthetic best quality enamel paint over a coats red oxide primer including providing necessary nuts and bolts , rubber packing grease etc , all labour charges for lifting and holding of pipes as per the necessity of welder at site.

OD241835/2023-2024:Supply and providing the rough cut flange ring joint 15 mm depth for 350 mm MS pipe after facing the cutting edges of flange rings neatly and set out the flange rings in correct position to both vertical and horizontal planes and welding in two rows accurately, painting two coats of synthetic best quality enamel paint over a coats red oxide primer including providing necessary nuts and bolts , rubber packing grease etc , all labour charges for lifting and holding of pipes as per the necessity of welder at site.

OD241704/2023-2024:Supply, conveying, erecting, testing and commissioning the 350 mm dia MS pipe in suction/ delivery side having sheet minimum thickness 6.35 mm and cutting in to required length, facing the cutting edges, painting two coats of synthetic best quality enamel paint over a coats red oxide primer, including conveyance charges to pump house and labour charges for loading, unloading, etc

90.4.5.4:Supply, Installation, testing and commissioning of ceiling fan of following sizes including wiring the down rods of standard length (up to 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required. 1200mm sweep - ceiling fan complete with service value minimum 4.0(cub meter/minute/Watt), Air delivery minimum 210(cubic meter/minute), Copper winding suitable for 230V/240V single phase AC supply

supply and Renewal of MS pipe at kalamassery LIS

OD242948/2023-2024:Dismantling the existing MS delivery pipe of size 200mmpiece by piece after providing scaffolding supports, with out further damages including MS bent , accessories etc. and stacking at the yard

OD242982/2023-2024:Supply, conveying, erecting, testing and commissioning the 200 mm dia MS pipe in suction/ delivery side having sheet minimum thickness 6.35 mm and cutting in to required length, facing the cutting edges, painting two coats of synthetic best quality enamel paint over a coats red oxide primer, including conveyance charges to pump house and labour charges for loading, unloading, etc

OD242983/2023-2024:Supply and providing the rough cut flange ring joint 12 mm thick for 200 mm MS pipe after facing the cutting edges of flange rings neatly and set out the flange rings in correct position to both vertical and horizontal planes and welding in two rows accurately, painting two coats of synthetic best quality enamel paint over a coats red oxide primer including fixing the pipe using suitable size nuts and bolts , rubber packing grease etc , in correct alignment and leakproof condition.

OD242984/2023-2024:Supply, fabrication, conveyance, fixing, testing and commissioning of 200 mm size MS pipe bend with 12 mm thick flanges at both end, fabricated from 200 mm MS pipe having 6.35 mm sheet thickness, with length not less than 1.75 meter, painting two coats of synthetic enamel paint over a coat of red oxide primer and fixing in position using fresh rubber packing, gaskit packing, bolts and nuts etc. in correct alignment and leak proof condition.

Bidder Name

FRANCIS PINHERO