REPAIR AND MAINT OF SOLAR WATER HEATER MECHANICAL LAUNDRY PLANT WATER DOSING PLANT AND HOT WATER GENERATOR INSTALLED AT SWIMMING POOL AND OTHER MISC WORK AT IMA DEHRADUN

Amount

Day to day maintenance and inspection of chlorine dosing plant at various water supply installation inside the complex ,alongwith replacement of deffective parts of dosing plant i.e injector assembly, connecting pipes and valve of each plant including strip opening of chloronome plant and replacement of all defective parts, washers by employing one skilled mechanic to achieve satisfactory residual chlorine result at user end from 0900 hrs to 1700 hrs during every working day. Note :-(I) Non attending complaint of chloronome plant is subject to a recovery of Rs 2500.00 per plant per day will be recovered while claiming the payment. (ii) Supply of spare parts shall be measured and paid for separately under respective items of BOQ.

Supply only Orthotoline Solution in 500 ML Bottle Note:- Consumable in water supply installation having batch No.with manufacturing date should not exceed more than 90 days complete all as directed.

Supply and fix in replacement,high pressure transparent type Suction/Discharge PVC pipe 3/8 '' dia outer of chloronome plant, as per OEM requirements complete all as specified and as directed.

Taking down existing defective electric motor of dosing motor 1 HP cap and supply and fix in replacement of dosing motor 1 HP cap squirrel cage type single phase 230 volt 50 Hz cap re-installation at site complete and testing complete all as specified and as directed by Engineer-in-Charge. Make:- .

M&L for taking down defective electric motor of dosing motor 1 HP cap disconnecting delivery pipe line repair/overhauling 1 HP, AC 230 volts opening into parts cutting of burnt winding, cleaning, slots, balancing of rotor, cleaning polishing and rewinding with same gauge of PVC insulated copper wire, replacement of impeller pressure switch and cleaning including testing complete all as specified and directed. .

Supply only spare parts for Dosing cum feeding pump of chloronome plant, gear type of cap 40 Gallon/per day Make:- Declibac and potter and watts to be incorporated in the work under ser item No 01 here in before are as following:-

Rotor assembly with bearing brackets and tollerance rings

Coil assembly 250V 50 Hz

Single head feed rate control with shaft

Pump Head ( Ferrules 1/4'' and duckbill included)

Roller assebly set of 4

Pump Tube (Set of Five)

Injection Check Valve 3/8" (Set of Five)

Weighted suction line strainer 3/8"

Ferrule 1/4" (set of 24)

Check valve for Duckbill (Set of 5)

PCB Plate

Diafram

Ajitator

connecting nut 3/8" mail & female Note : Make of spare parts mentioned in 6.01 to 6.15 above shall be as per existing at site i.e. Declibac or Pearls filter as per site requirement and as directed by Engineer-in-Charge.

Supply only Calcium Hypo Chlorite 65-70% chlorine content in granular form disinfectant for water treatment packed in 45 Kg Drum. Make: sree Rayalaseema Hi- srength Hypo Ltd & E-in-C Approved. Note:-Consumable in water supply installation having batch No.with manufacturing date should not exceed more than 90 days complete with manufacturers test certificate.

Supply only copper sulphate for water treatment as approved by GE. Note:-Consumable in water supply installation having batch No.with manufacturing date should not exceed more than 90 days.

Supply only Alum crystal type in swimming pool for agitation and water treatment as approved by GE. Note:-Consumable in water supply installation having batch No.with manufacturing date should not exceed more than 90 days.

Testing of water from NABL approved testing lab for 27 standard parameters from Pump House ,bore well at different locations under GE IMA Dehradun complete all as specified and directed .

Periodical servicing/maintenance of industrial Tumble dryer-T5675 of Electrolux- including taking down carefully all deffective parts, for repair/ servicing, comprising strip opening of plant,re-assembling & testing on load , as directed by Engineer-in-Charge. Note:- (i) Fixing of the new part(s)shall be deemed to be included on rates quoted by the contractor for this item and new parts shall be measured and paid separately as under supply fix catagory against respective items of 'BOQ'. (ii) Repair/replacement of deffective parts shall be done witin 72 Hrs after intimation by the Engineer-in-Charge. (iii) Once servicing of plant carried out by contractor will be responsible for entire contract preriod for replacing any other deffective part which falls under supply and fixing catagory without any extra cost to govt. (iii) Required T&P for lifting/shifting of plant is contractors own arrangement without any extra cost to govt. (iv) The contractor shall maintain records of all kinds of maintenance to be carried out.

S&F bearing as per existing type and size.

S&F Felt sealing as per existing type and size.

S&F Guide roller of drum as per existing type and size.

S&F screw of drum mechanism as per existing type and size.

S&FVacuum switch of drum mechanism as per existing type and size.

S&Fcontactor 50 Hz, 32 Amps as per existing type and size.

S&F contactor 50 Hz, 40 Amps as per existing type and size.

S&F cable set of contactor as per existing type and size.

S&F transformer 208-240V as per existing type and size.

S&F heating element 240 volt 8 kW as per existing type and size.

Periodical servicing/maintenance of industrial washer extractor with microprocessor panel Make and model of plant W5330S of Electrolux- ,Including taking down carefully all deffective parts, for repair/ servicing, comprising strip opening of plant, re-assembling & testing on load, as directed by Engineer-in-Charge. Note:- (i) Fixing of the new part(s)shall be deemed to be included on rates quoted by the contractor for this item and new parts shall be measured and paid separately as under supply and fix against respective items of 'BOQ'. (ii) Repair/replacement of deffective parts shall be done witin 72 Hrs after intimation by the Engineer-in-Charge. (iii) Once servicing of plant carried out by contractor will be responsible for entire contract preriod for replacing any other deffective part which falls under supply only catagory without any extra cost to govt. (iii) Required T&P for lifting/shifting of plant is contractors own arrangement without any extra cost to govt.(iv) The contractor shall maintain records of all kinds of maintenance to be carried out.

S&F stainless screw M6X12 of outer drum unit as per existing type and size.

S&F front door lock as per existing type and size.

S&F electrical drain valve as per existing type and size.

S&F rubber hose pipe 73 mm dig with suitable size of clamp for drain valve as per existing type and size.

S&F heating element 6.6 KW cap 240 Volt as per existing type and size.

S&F heating sensor as per existing type and size.

S&F Transformer as per existing type and size.

S&F contactor 3 pole 50 Hz 32 Amp as per existing type and size.

S&F front door gassket EPDM black as per OEM design complete all as specified and as directed.

S&F hinged joint of door as per OEM design complete all as specified and as directed.

S&F Lock shaft assy of door as per existing type and size.

S&F ribbed belt of electric motor poly V type as per existing type and size.

S&F motor control unit (VFD) with invertor assy complete 3 phase 440 volt AC motor as per existing type and size

S&F Valve of steam section as per existing type and size.

Servicing/maintenance of industrial flat work rotary ironer running chest size 2.0 mtr long IC 43320 of Electrolux make- ,including taking down carefully all deffective parts, for repair/ servicing, comprising strip opening of plant, re-assembling & testing on load, as directed by Engineer-in-Charge. Note:- (i) Fixing of the new part(s)shall be deemed to be included on rates quoted by the contractor for this item and new parts shall be measured and paid separately as under supply and against respective items of 'BOQ'. (ii) Repair/replacement of deffective parts shall be done witin 72 Hrs after intimation by the Engineer-in-Charge. (iii) Once servicing of plant carried out by contractor will be responsible for entire contract preriod for replacing any other deffective part which falls under supply only catagory without any extra cost to govt. (iii) Required T&P for lifting/shifting of plant is contractors own arrangement without any extra cost to govt. (iv) The contractor shall maintain records of all kinds of maintenance to be carried out.

S&F Control panel as per existing type and size.

S&F Temprature sensor as per existing type and size.

S&F Trim as per existing type and size.

S&F Ironing strip as per existing type and size.

S&F Temprature sensor secondry as per existing type and size.

S&F Temprature sensor safty as per existing type and size.

Annual servicing/maintenance of industrial industrial vaccum finish iron table 1200mmX750 mm complete with steam genarator of Fabcare make. including taking down carefully all deffective parts, for repair/ servicing, comprising strip opening of plant, re-assembling & testing on load, as directed by Engineer-in-Charge. Note:- (i) Fixing of the new part(s)shall be deemed to be included on rates quoted by the contractor for this item and new parts shall be measured and paid separately as under supply and fix against respective items of 'BOQ'. (ii) Repair/replacement of deffective parts shall be done witin 72 Hrs after intimation by the Engineer-in-Charge. (iii) Once servicing of plant carried out by contractor will be responsible for entire contract preriod for replacing any other deffective part which falls under supply only catagory without any extra cost to govt. (iii) Required T&P for lifting/shifting of plant is contractors own arrangement without any extra cost to govt.(iv) The contractor shall maintain records of all kinds of maintenance to be carried out.

S&F teflon pad of iron machine of 150mmx230mm size per OEM design complete all as specified and as directed.

S&F heating element shoe of iron machine single phase 900 watt 230 volt ISI mark as per OEM design complete all as specified and as directed.

S&F heating element 'U' shape for iron table single phase 3.0 KW 230 volt ISI mark as per OEM design complete all as specified and as directed.

S&F heating element of steam vessel single phase 3 KW cap ISI mark as per OEM design complete all as specified and as directed.

S&F Aluminium shoes of iron machine ISI mark as per OEM design complete all as specified and as directed.

S&F steam rubber pipe of 10kg pressure 3 mtr long nylon embeded of iron machine ISI mark as per OEM design complete all as specified and as directed.

S&F pressure gauge of steam tank of 10kg pressure rating ISI mark as per OEM design complete all as specified and as directed.

S&F contactor 4 pole single phase 25 amp cap of of iron machine steam tank of 10kg pressure rating ISI mark as per OEM design complete all as specified and as directed.

S&F single phase,230volt water level controller switch of steam vessel ISI mark as per OEM design complete all as specified and as directed.

S&F steam solonoid valve 1/2' cap 230 volt single phase of steam vessel ISI mark as per OEM design complete all as specified and as directed.

S&F pressure switch 1/2' cap 230 volt single phase of steam vessel ISI mark as per OEM design complete all as specified and as directed.

S&F single phase micro switch of paddlel ISI mark as per OEM design complete all as specified and as directed.

S&F single phase rocker switch 15 Amp cap ISI mark as per OEM design complete all as specified and as directed.

Supply and fix in replacement Wall mounting industrial socket 63 amp cap 5 pin ,3P+N+E 415 volts,AC splash proof IP 67 protected make C&S cat part No CS 63249 or equivalent in ABB,Legrand complete all as directed.

Supply and fix in replacement Wall mounting industrial plug 63 amp cap 5 pin ,3P+N+E 415 volts,AC splash proof IP 67 protected make C&S cat part No CS 61048 or equivalent in ABB,Legrand complete all as directed.

Supply and fix in replacement of MCCB 4 pole 63 Amp cap,Thermal Magnetic release conforms to IS/IEC 60947-2 breaking cap 36kA suitable for isolation ,adjustable overload from 0.67 to 1.0In, adjustable short circuit setting from 6.0 to 12 x Ir inbuilt earth fault protection make L&T or equivalent C&S, ABB,Legrand complete all as directed.

Supply and fix in replacement of MCCB 4 pole 250 Amp cap,Thermal Magnetic release conforms to IS/IEC 60947-2 breaking cap 36kA suitable for isolation ,adjustable overload from 0.67 to 1.0In, adjustable short circuit setting from 6.0 to 12 x Ir inbuilt earth fault protection make L&T C&S, ABB,Legrand complete all as directed.

M&L earthing with galvanized iron earth plate of size 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 meter below normal ground level connected to galvanized earth lead iron strip 32 x 6mm dia by means of volts, nuts, check nuts and washers of galvanized iron or steel including excavation/earth work in any type of soil, returning filling in removal of surplus soil, to a distance upto 50 mtr PCC 1 : 3 : 6 type C-1 earth pit, RCC cover with suitable handle for lifting, water pipe, funnel etc complete all as shown in electrical plate No 3 of SSR part-I all as specified including testing on completion.

M&L for PCC 1:3:6 type C-1 (using 20 mm crushed granite stone aggregate) as in coping, including necessary form work complete all as specified and directed

M&L for rendering to brick/ concrete surfaces, 10 mm thick in cement mortar 1:4, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for Cross arms, bracings, supports,clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint.

S & Fix in replacement switch socket outlet multipurpose , 3 Pin 15/16 and 3pin 5/6Amp , 240 Volt , controlled by one switch all as directed by Engineer in Charge. Make:- Anchor,Havells,Crompton.

M&L for Sub main wiring with two single core cable PVC insulated unsheathed cable multi standard with copper conductor 1100 Volts grade of size 6 Sqmm drawn through and including medium grade PVC rigid conduit and conduit accessories ISI marked with PVC cable copper conductor 6 Sqmm multi stranded unsheathed cable as earth conductor concealed in wall, beams and columns all as directed.

M&L for Sub main wiring with two single core cable PVC insulated unsheathed cable multi standard with copper conductor 1100 Volts grade of size 10 Sqmm drawn through and including medium grade PVC rigid conduit and conduit accessories ISI marked with PVC cable copper conductor 10 Sqmm multi stranded unsheathed cable as earth conductor concealed in wall, beams and columns secured with proper saddling complete all as directed.

Through Cleaning of Drain valve of Washer extracrtor after unplug from plant by technically skilled person and refix the same every after 15 days complete all as specified and as directed.

Through Cleaning of Filter hatch of tumble dryer after unplug from plant by technically skilled person and refix the same every after 15 days complete all as specified and as directed.

Taking down defective electric & motor from driyer of any make , shifting the same to workshop, strip opening after unscrewing nut bolts screws etc. taking out rotor from stator, cutting and taking out burnt winding carefully from the stator, cleaning of slots, rewinding of stator with super enamelled copper winding wire of appropriate size matching with manufactures design including replacement of all insulating materials such as glass paper ,leathered paper, super enameled copper conductor wire connection leads of appropriate size with sleeves of suitable size up to terminal connection box , varnishing, drying up and re-assembling refixing and reinstallation in plant including replacement of bearing and leathe work and complete and testing on load all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement, PVC insulated,un-armoured, heavy duty electric power cable 6 Sqmm 4 core copper conductor, 1100 volts grade, etc complete all as specified and directed.

Supply and fix in replacement, PVC insulated,un-armoured, heavy duty electric power cable 4 Sqmm 3 core copper conductor, 1100 volts grade, etc complete all as specified and directed.

Supplying and laying in rep-lacement of CPVC pipes SDR 11 and plain CPVC SDR 11 fittings in wall ceilling and floors of size 20 mm dia complete all as specified. Make:-Astral/Prayag polymer/Supreme.

Supplying and laying in rep-lacement of CPVC pipes SDR 11 and plain CPVC SDR 11 fittings in wall ceilling and floors of size 25 mm dia complete all as specified. Make:-Astral/Prayag polymer/Supreme.

Supplying and laying in rep-lacement of CPVC pipes SDR 11 and plain CPVC SDR 11 fittings in wall ceilling and floors of size 50 mm dia complete all as specified. Make:-Astral/Prayag polymer/Supreme.

Supply and fix in replacement Male brass threaded adaptor (MTA/MBTA) 20 mm outer dia.

Supply and fix in replacement Male brass threaded adaptor (MTA/MBTA) 25 mm outer dia.

Supply and fix in replacement female brass threaded adaptor (FTA/FBTA) 50 mm outer dia.

Supply and fix in replacement female brass threaded adaptor (FTA/FBTA) 25 mm outer dia.

Supply and fix in replacement CPVC union 20 mm outer dia.

Supply and fix in replacement CPVC union 25mm outer dia

Supply and fix in replacement CPVC union 50 mm outer dia

Strip opening and descalling/gaswelding of water collector of Solar panel 1500 Ltrs/day capacity over rooftop of 3 rd floor or fixed in ground, fins/tubes from inside, (vertical type) cleaning with concentrate acid in fix ratio and repair /copper welding (soldering) of panel including replacement of rubber washer 2 Nos of thickness 3 mm, and arresting of detecting possible leakage reassembling and reinstallation at over OTM buildings with OEM approved manufacturer complete all as specified and directed.

S&F in replacement of Toughened/Texture glass of 3.2 mm thik having transmission more than 85 % including coonected rubber/nut botl/nickle cladding etc in the existing solar panel complete all as directed.

S&F heating element for solar water heating system of cap 3 KW as per existing type and size.

S&F thermostat control for electrical back up as per existing type and size.

S&F EPDM rubber gasket for solar collector as per existing type and size.

M&L for insulation for GI pipe with glass wool 30mm thick with and including applying bituminous compound and aluminium cladding of sizes 20 mm dia complete all as directed.

M&L for insulation for GI pipe with glass wool 30mm thick with and including applying bituminous compound and aluminium cladding of sizes 25 mm dia complete all as directed.

M&L in repairs of VALVE, SOLENOID 1/2" BSP No

M&L in repairs of RECTIFIER-110-240V,AC / 180 DC, SKB 25,SIMICRON

M&L in repairs of CAP RUBBER for photocell

M&L in repairs of THERMOMETER 0-600 DEG,100 MM

M&L in repairs of HOSE METALLIC BRAIDED 3/8" x 40" LG

M&L in repairs of HOSE METALLIC BRAIDED 3/8" x 50" LG

M&L in repairs of BURNER ROD OBT 50- 352 MM LONG

M&L in repairs of HOOTER ROUND

M&L in repairs of SEALS SET

M&L in repairs of THERMOMETER 0-600 DEG,100 MM DIAL

M&L in repairs of PRESSURE GAUGE , 0 TO 40 KG 68 MM, 1/4" BSP BOTTOM CONNECTION

M&L in repairs of NOZZLE BYPASS ASSEMBLY40 GPH 2 MM ORIFICE

M&L in repairs of CONTINUOUS CURRENT MAGNET 180 V,DC

M&L in repairs of ELECTRODE 800 MM LONG

M&L in repairs of ELECTRODE CAP WITH HT CABLE

M&L in repairs of NOZZLE HOLDER

M&L in repairs of SEQUENCE CONTROLLER LAL 2.25 WITHOUT BASE PLATE

M&L in repairs of PHOTORESISTOR QRB 3

The service charges for the service visit by OEM Service Engineer for checking/fixing of spare part to the hot water generator/ thermic fluid heater complete all as directed.

S&F of First Aid Box of size 30x15x5 cm made out of GI sheet 2.0 mm thick including all standard medical treatment equiptment compleate all as specified.

Supply and filling sand in Chlorine defusing pit at various water supply installation complete all as directed.

Material & labour for making of Notice board of size 4'x3' made out of wooden frame work, glass top double door with locking arrangement duly prewired with LED light batten 2 ft 20 watt incluing necessary mounting/fixing hooks as indicated and as directed by Engineer-in-charge.

M&L for making schematic/line diagram on acylic sheet of size 4"x2" including lettering/line/figure made out of radium sticker of size 9" in height to be written on the acrylic sheet including hangine hooks complete all as specified and directed by Engr-In-Charge: Note : (Model of schematic diagram shall be provided by the Engineer-in-charge and approved by GE.

M/s Anamika Enterprises