Beautification and Illumination work of Shree Jageshwar Dham Almora

Amount

Supply installation, testing & commissioning of LT panel suitable for 415 V, 3 phase 4 wire 50 Hz AC supply system, RYB LED indicators, VAF digital metering. Cable entry and outgoing are only with suitable sizes of screwless glands, including with all accessories copper bus bar, din rails, earth links, neutral links, glands, locks, connectors, operation complete with all respects. (as per the SLD attached no. LUC/J.D/SLD/T1A). Cubical : Supplying and erecting GI sheet 1.6 mm (16 SWG) to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint. (A) Supplying and erecting bus bar chamber triple pole with neutral with four copper bars, 500V, 100A -01 No complete as per specification (B) Supplying, erecting & marking FPMCCB 100A B series in provided distribution board as per specification - 01 Nos (C) Supplying, erecting & marking TPN MCB 6A to 32A, B series in provided distribution board as per specification - 05 Nos (D) Supplying, erecting & marking SPN MCB 6A to 32A, B series (for lighting) in provided distribution board as per specification - 07 Nos (E) Supplying, installation & marking of surge arrestor / surge protection device at the main distribution board after the incoming breaker of type 1+2 tested for Imax 100 kA for three phase and neutral as per specification no. CP-SPD - 01 nos (F) Supplying & erecting single phase 2 wire system having in built astronomical adjustable programmable timer with minimum 5 years battery backup, 2 pole contactor upto 60 A, with maintenance mode to switch ON -03 Nos

Supply,installation, testing and commissioning of the servo voltage stablizer of following ratings, 3-phase, Copper winding, 50HZ Frequency, Unbalanced input voltage and unbalanced load, Volt/ampere meter CT's, input voltage range- 360V-480V, output voltage range- 410-420V adjustable 60KVA

Supplying, erecting and commissioning of diesel generating set with alternator of 62.5 kVA output continuous rating, 3 phase, 415 V, 50c/s 0.8 p. f. A.C a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 15

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required. (Note: Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required 40 A

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A

Supply, installation, testing and commissioning of the PC (Polycarbonate) Termination junction box (IP66), terminal with 2 clamping units per pole 5-pole per pole, 4 x 4 mm² r / f, included cable entry: 3 x ESM 40, sealing range Ø 17-30 mm with one cable entries M 32 from the rear side lid fasteners sealable without accessories external brackets for wall fixing included colour: grey, RAL 7035, rated insulation voltage Ui = 690 V a.c./d.c., in accordance with IEC 60670-22, Incoming - 1 no. 4 core 4.0/2.5 sq mm copper armoured cable Outgoing - 2 nos. 3 core 2.5/1.5 sq mm copper armoured cable. Built-in dimensions W 210 x H 155 x D 92 (Tolerance ± 10%) material: PC (polycarbonate), impact strength IK 09 (10 Joule), in accordance with IEC 62208:2011

Supply installation testing & commisioning of Empty box (IP66) with installation equipment on DIN rails or mounting plates (order separately) with opaque lid fastener for tool operation sealable box walls without knockouts external brackets for wall fixing included, colour: grey, RAL 7035, material: PC (polycarbonate) mounting plate, glands and complete with all required accessories and hardware to complete the job in all resepcts. Built in dimensions W 170 x H 220 x D 96 (Tolerance ± 10%) material: PC (polycarbonate), impact strength IK 09 (10 Joule), in accordance with IEC 62208:2011

Supply installation testing & commisioning of Empty box (IP66) with installation equipment on DIN rails or mounting plates (order separately) with opaque lid fastener for tool operation sealable box walls without knockouts external brackets for wall fixing included, colour: grey, RAL 7035, material: PC (polycarbonate) mounting plate, glands and complete with all required accessories and hardware to complete the job in all resepcts. built in dimensions W 215 x H 320 x D 106 (Tolerance ± 10%) material: PC (polycarbonate), impact strength IK 09 (10 Joule), in accordance with IEC 62208:2011

Providing & erecting steel perforated type cable tray manufactured from 16 swg (1.6 mm thick) Steel sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware in the approved manner.

25 mm dia. ISI marked, PVC conduit

25 mm PVC bends

25 mm dia. ISI marked, steel conduit

25 mm inspection/ solid bends

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supply installation testing & commissioning of 6.0-meter height 75mm dia, C class MS pole, anthracite grey paint, with plate mounting arrangement, plate size 450mm X 450mm X 20mm suitable for bracketless direct lighting fixture installation.

Laying of PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of the following size in the existing RCC/ HUME/ METAL/DWC pipe as required. Upto 35 sq. mm

Supply of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground/DWC Pipe including excavation, sand cushioning, protective covering and refilling the trench etc as required. 3.5C x 35 Sq.mm. Aluminum XLPE armored cable

Supply, connection, testing and commissioning of heavy duty, medium voltage, XLPE (IS 7098 - PART-II) insulated, Stranded AL / Cu conductor Armoured / Flexible cables as per specification & IS. The cable shall have outer sheeth of XLPE and inner sheath of PVC with stranded AL conductor wherever specified. The cable shall be laid underground in excavated trench / prepared trench / hume pipes when laid outside the building. Cable shall be laid throught preapred trench / cable tray / duct / hume pipe / channel / floor trunks etc when laid inside the building as instructed by PMC/Site Incharge. 4C x 6 Sq.mm. CU XLPE armored cable

4C x 4 Sq.mm. CU XLPE armored cable

3C x 4 Sq.mm. CU XLPE armored cable

3C x 2.5 Sq.mm. CU XLPE armored cable

Supply and Providing heavy duty double compression brass gland and lugs end terminations,IP 66 complete,SIBG type, for the cable specified under above item with Bi-metallic lugs using crimping tool, Insulation tape, Identification tags etc., including end termination and Earthing of Gland. 4C x 6 Sq.mm. CU XLPE armored cable

4C x 4 Sq.mm. CU XLPE armored cable

3C x 4 Sq.mm. CU XLPE armored cable

3C x 2.5 Sq.mm. CU XLPE armored cable

3.5C x 35 Sq.mm. Aluminum XLPE armored cable

DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)

120 mm dia (OD-120 mm & ID-103 mm nominal)

1000mm Linear LED 25W- 2400K-5000K: Supply installation testing & commissioning of exterior-rated architectural floor/wall mounted IP67 or IP68, 1000mm long linear light complete with visor and adjustable mounting brackets/clamps (as per application). The power consumption should not be more than 25 watts, 10 x 30°/30 X 30° beam angle with a tolerance of ±15%, Tunable from 2400K-5000K. The housing material should be extruded aluminum, a powder-coated finish, luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware, DMX controller & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

1000mm Linear LED 15W- 2400K-5000K: Supply installation testing & commissioning of exterior-rated architectural floor/wall mounted IP67 or IP68, 1000mm long linear light complete with visor and adjustable mounting brackets/clamps (as per application). The power consumption should not be more than 15 watts, 10 x 30°/30 X 30° beam angle with a tolerance of ±15%, Tunable from 2400K-5000K. The housing material should be extruded aluminum, a powder-coated finish, luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware DMX controller & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

500mm Linear LED 25W/M- 2400K-5000K: Supply installation testing & commissioning of exterior rated architectural floor/wall mounted IP67 or IP68, 500mm long linear light complete with visor and adjustable mounting brackets/clamps (as per application). The power consumption should not be more than 25 watts per meter, 10 x 30°/30 X 30° beam angle with a tolerance of ±15%, Tunable from 2400K-5000K. The housing material should be extruded aluminum, a powder-coated finish, luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware DMX controller & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

500mm Linear LED 15W/M- 2400K-5000K: Supply installation testing & commissioning of exterior rated architectural floor/wall mounted IP67 or IP68, 500mm long linear light complete with visor and adjustable mounting brackets/clamps (as per application). The power consumption should not be more than 15 watts per meter, 10 x 30°/30 X 30° beam angle with a tolerance of ±15%, Tunable from 2400K-5000K. The housing material should be extruded aluminum, a powder-coated finish, luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware DMX controller & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

300mm Linear LED 25W/M- 2400K-5000K: Supply installation testing & commissioning of exterior rated architectural floor/wall mounted IP67 or IP68, 300mm long linear light complete with visor and adjustable mounting brackets/clamps (as per application). The power consumption should not be more than 25 watts per meter, 10 x 30°/30 X 30° beam angle with a tolerance of ±15%, Tunable from 2400K-5000K. The housing material should be extruded aluminum, a powder-coated finish, luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware DMX controller & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

300mm Linear LED 15W/M- 2400K-5000K: Supply installation testing & commissioning of exterior rated architectural floor/wall mounted IP67 or IP68, 300mm long linear light complete with visor and adjustable mounting brackets/clamps (as per application). The power consumption should not be more than 15 watts per meter, 10 x 30°/30 X 30° beam angle with a tolerance of ±15%, Tunable from 2400K-5000K. The housing material should be extruded aluminum, a powder-coated finish, luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware DMX controller & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Neon Flex LED 20W/M- RGBW: Supply installation testing & commissioning of exterior rated architectural floor/wall mounted IP68, neon flex complete with adjustable mounting brackets/clamps (as per application). The power consumption should not be more than 20 watts per meter, diffused, CCT RGBW. The housing material should be extruded aluminum, a powder-coated finish, luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware DMX controller & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Ring Flex Washer LED 20W/M- RGBW: Supply installation testing & commissioning of exterior rated architectural floor/wall mounted IP67 or IP68, flex washer 500mm/1000mm/1500mm (Size- actual size as per site measurement) dia ring up light complete with adjustable mounting brackets/clamps (as per application). The power consumption should not be more than 20 watts per meter, diffused, CCT RGBW. The housing material should be extruded aluminum, a powder-coated finish, luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware DMX controller & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Flood Light LED 50W- 3000K/4000K: Supply installation testing & commissioning of exterior rated architectural floor/wall mounted IP67, flood light with antiglare snoot complete with adjustable mounting brackets/clamps (as per application). The power consumption should not be more than 50 watts, 4000 delivered lumens, 30° beam angle with a tolerance of ±15%, CCT-3000K/4000K. The housing material should be extruded aluminum, a powder-coated finish, anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be integral non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP67 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Flood Light LED 100W- Blue color: Supply installation testing & commissioning of exterior rated architectural floor/wall mounted IP67, flood light with antiglare snoot complete with adjustable mounting brackets/clamps (as per application). The power consumption should not be more than 100 watts, 40° beam angle with a tolerance of ±15%, CCT-Blue color. The housing material should be extruded aluminum, a powder-coated finish, anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be integral non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP67 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

1000mm Linear LED 10W- 2700K: Supply installation testing & commissioning of exterior-rated architectural floor/wall mounted IP67 or IP68, 1000mm long linear light complete with visor and adjustable mounting brackets/clamps (as per application). The power consumption should not be more than 10 watts, 10 x 30°/25° beam angle with a tolerance of ±15%, CCT 2700K. The housing material should be extruded aluminum, a powder-coated finish, luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Diya Bollard Flickring LED 10W- 2700K: Supply installation testing & commissioning of exterior-rated decorative floor mounted IP66 or IP67, 200mm high bollard, and mounting brackets/clamps (as per application). The power consumption should not be more than flickering 10 watts, diffused, CCT 2700K. The housing material should be extruded aluminum, a powder-coated finish, anti-aging and anti-UV, diffused tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be integrated non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK08. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Decorative light LED 10W- 3000K: Supply installation testing & commissioning of exterior-rated decorative floor mounted IP66 or IP67, 450mm dia globe light, and mounting brackets/clamps (as per application). The power consumption should not be more than 15 watts, diffused, CCT 3000K. The housing material should be extruded aluminum, a powder-coated finish, anti-aging and anti-UV, diffused tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be integrated non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are included. Minimum IK08. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self-declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Flood Light LED 15W- 2700K: Supply installation testing & commissioning of exterior rated architectural floor/wall mounted IP67, flood light with antiglare snoot complete with adjustable mounting brackets/clamps (as per application). The power consumption should not be more than 15 watts, 800 delivered lumens, 8° beam angle with a tolerance of ±15%, CCT-2700K. The housing material should be extruded aluminum, a powder-coated finish, anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be integral non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP67 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

500mm Linear LED 25W/M- RGBWW: Supply installation testing & commissioning of exterior rated architectural floor/wall mounted IP67 or IP68, 500mm long linear light complete with visor and adjustable mounting brackets/clamps (as per application). The power consumption should not be more than 25 watts per meter, 10 x 30°/30 X 30° beam angle with a tolerance of ±15%, CCT RGBW. The housing material should be extruded aluminum, a powder-coated finish, luminaire body color should be similar to the facade color surface where the luminaire is to be installed with anti-aging and anti-UV high optical efficiency PMMA lenses, Clear tempered glass cover. It should have CRI>80, and SDCM≤4. The driver should be remote non dimmable with PF>0.9 & THD<20%. Leader cables, jumper cables, IP68 connectors are inclusive. Minimum IK06. The operating temperature should be of -20°C to 50°C range. Lifetime of luminaire (L70 @ Ta-35deg C) should be at least 50,000 burning hours. Luminaire should have corrosion resistance with self declaration of ASTM B117 for 500 hours of salt spray test. All mounting accessories shall be stainless steel (Minimum -316) for all lighting fixtures. The luminaire should be BIS certified. This includes all the required hardware DMX controller & software for the successful operation of the luminaire. (All the technical parameters of the luminaire need approval from the lighting consultant)

Supply installation testing & commissioning of 3 Chip DLP Laser Projector with min 45000 ± 5% Lumens Brightness, 95% or more brightness uniformity, 20000:1 contrast or more, Native Resolution 1920x1200 (WUXGA), 20000 Hrs or more illumination, Inbuilt Warping & Blending. HDMI 2.0, DP 1.2, HDbaseT inputs. RS 232/Ethernet control. Supplied With long throw lens.

Supply installation testing & commissioning of weatherised enclosers for equipment. Equipment should be complete with fans & temperature and humidity sensors remote controlled with all accessories.Enslosure should also have built in airconditioner for maintaining ambient temperature and humidity inside enclosure.

Supply installation testing & commissioning of Display media server with 4nos x HD outputs as required, synced together. It should be capable of capturing content. Original Windows 10 embedded with Intel Xeon CPU with Rugged cooling system. with 16GB RAM, 512 nVME SSD drive for media playback. Should also have Art-net Ethernet in/out. to complete the job with all respects. Min. 1x NVidia Quadro RTXA4000 or equivalent

Supply installation testing & commissioning of Display media server with 4nos x HD outputs as required , synced together. It should be capable of capturing content. Original windows 10 embedded with Intel Xeon CPU with Rugged cooling system. with 16GB RAM, 512 nVME SSD drive for media playback. Should also have Art-net Ethernet in/out. to complete the job with all respects, to be supplied with Monitor

Supply installation testing & commissioning of 3D Projection mapping software, Playback control System to manage, schedule & control the media servers. It should have direct control on inputs and media timelines. It should have an option of being controlled by an external unit integrated with the software to complete the job with all respects.

6 core armoured multimode Fibre Optic Cable

HDMI Fibre Optic Extender with range up to 300 meters

4sqmm, 3 core electrical cable for projectors from Control room with termination, mtr

Electrical Panel for Projectors and Server in control room

16 Port Gigabit Network Switch

19U Equipment Rack

Cat 6e cable, mtr

Supply installation testing & commissioning of Full range environmental rated (IP55 or better) In Ground or Above ground Landscape PA/ Music loudspeaker with one downward firing 4.5" (114 mm) advanced composite environmental full-range driver. Domed port grille for clear, consistent sound quality, The Speaker shall have a rated impedance of 4 Ω and shall have a line voltage matching (step down) transformer with taps at 80 watts or better. The nominal dispersion of the loudspeaker shall be 360° horizontal and 50° vertical at least.

Supply installation testing & commissioning of OF12-Channel Mixing Console Max. 6 Mic / 12 Line Inputs (4 mono + 4 stereo). 2 GROUP Buses + 1 Stereo Bus. 2 AUX (incl. FX). D-PRE” mic preamps with an inverted Darlington circuit. 1-Knob compressors. High-grade effects: SPX with 24 programs. 24-bit / 192kHz 2in / 2out USB Audio functions. Works with the iPad (2 or later) through the Apple iPad Camera Connection Kit / Lightning to USB Camera Adapter. Includes Cubase AI DAW software download version. PAD switch on mono inputs. +48V phantom power XLR balanced outputs. Internal universal power supply for worldwide use.

Supply installation testing & commissioning of Dynamic cardioid microphone for speech and vocals with noiseless on/ off switch Cuts through high on-stage levels Clear reproduction with a high presence Consistent sound quality (varying distances, moving off-axis) Handles high sound pressure levels Isolates handling noise, hum compensating coil Excellent feedback rejection.

Supply installation testing & commissioning of 2 core 14 AWG/2.5 Sq mm, Twisted, unshielded Speaker cable with stranded annealed bare copper conductors, Semi-rigid PVC insulation, NEC CL3R, CEC CMG, RoHS compliant.

Supply installation testing & commissioning of 2 core Twisted, shielded balanced Audio and control cable with 22AWG or better 7 strand annealed bare copper conductors, Semi-Rigid PVC insulation, Riser rated PVC jacket. UL 444, UL 13 CMR rated.

Supply installation testing & commissioning of Outdoor rated surface mounted powder coated aluminium alloy having wall thickness of minimum 3MM on all sides, with width limited to 140 MM or less & height limited to 60 MM or less, to house IP67 rated two light fixtures as per the BoQ, wiring management and IP68 GEL connectors for internal connections, and to withstand load of 20 MM to 50 MM thick stone on top, for walkover application. It should have proper end caps to cover and protect the wiring. as per detail drawing given

Supply installation testing & commissioning of Outdoor rated floor recessed stainless steel as per IS-277, Powder Coated, and SS-202/304/316. Width 100mm, Height 50mm, this includes all types of hardware and accessories

S/L of following size DWC HDPP pipe ISI Mark along with all accessories, IS 14930 Part 2 complete with fitting and cutting jointing etc. Direct in ground 75 cm below ground level including excavation and refilling the trench work excluding send cushioning and protective covering etc complete as required. 120 mm dia (OD -120 mm and ID- 103 mm nominal)

Supply, installation, testing and commissioning of UTP 4 pair Cat6 cable in existing surface/recessed PVC or steel conduit. CAT6 4Pair 23 AWG UTP cable ,.Category 6 UTP cables shall Supports Gigabit Ethernet (1000 base-T) standard and Operates at bandwidth of 600MHz. Construction: 4 twisted pairs separated by internal X shaped, 4 channel, polymer spine / full separator. Half shall not be accepted. cable well exceeds the requirements of TIA/EIA-568-C.2 and ISO/IEC 11801 Conductor Solid bare Copper and Jacket FR PVC and UL approved CM rated cable and Outer jacket sheath of the cable shall be LSZH. Insulation :High Density Polyethylene ,Attenuation (< 17 db), Pair – to – pair and PS NEXT, ELFEXT and PSELFEXT, Return Loss, ACR and PS ACR.Dielectric Strength of cable should be 1.0KV

28-Port Gigabit Smart Managed PoE Switch 24 x 10/100/1000BASE-T PoE ports ; 4 x Gigabit RJ45/SFP Combo portsAdvanced L2 switching and security features L2+ Static RoutingOptional “standard mode” or “surveillance mode” management user interface ; 193 W PoE budgetNetwork Security The LAN switch shall support IEEE 802.1x to allow dynamic, port-based security, providing user authentication. It shall support RADIUS authentication to enable centralized control of the switch and restrict unauthorized users from altering the configuration. It shall have built in mechanism to protect the switch against traffic flooding caused by virus attack VLAN The LAN switch shall have IEEE 802.1Q VLAN encapsulation. Up to 255 VLANs per switch. It shall have Management Vlan It shall have Asymmetric VlanPerformance The Switch shall have Non-blocking wire speed switch fabric , The Switch shall have Min. 56 Gbps Back plane or higher , The Switch shall support Min. 16K Mac address The Switch shall support Min. 256 VLANs , The Switch Should support Jumbo Frame (up to 9,216 Bytes)

Supply, installation, testing and commissioning of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

Supply, Installation, Testing & Commissiong of IP BULLET CAMERA(Outdoor) Supply of 5MP IR Bullet camera with 1/2.9‑inch CMOS, Total sensor pixels 3072 (H) x 1728 (V); up to 25fps; Sensitivity – Measured according to IEC 62676 Part 5 (1/30, F1.6), Color 0.379 lx, Mono 0.042 lx, With IR 0.0 lx, 120dB WDR, H.265; H.264; M- JPEG, Automatic Electronic Shutter (AES); Intelligent Dynamic Noise Reduction, Intelligent Defog,Rule based alarms and tracking, Line crossing, Enter / leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimation, 3D tracking based on Duration, Size, Aspect ratio v/h, Speed, Direction, Color, Object classes (Upright persons, Bikes, Cars, Trucks), Privacy Masking, Pixel counter, Memory card slot, IR Range 30mtr, Automatic Varifocal 3.2 to 10 mm, Alarm Input 1/1, Audio Input/output, RJ45, G.711, Audio Streaming Full-duplex / half duplex, ONVIF Profile S, G & T, IP66, IK10, PoE, CE, FCC, UL certified. SD card support up to 2TB. FTP, Dropbox and e-mailapplications

Supply of 5MP Outdoor Dome camera: with 1/2.9‑inch CMOS, Effective pixels 3072 (H) x 1728 (V), up to 25 fps, Sensitivity – (Measured according to IEC 62676 Part 5 (1/30, F1.6)Color 0.397 lx Mono 0.042 lx With IR 0.0 lx, 120 dB Dynamic range, Electronic Day/Night, Automatic Electronic Shutter (AES), H.265, H.264 MP (Main Profile); M-JPEG Video compression, White balance, Backlight Compensation, Privacy Mask,Rule based alarms and tracking, Line crossing, Enter / leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimation, 3D tracking based on Duration, Size, Aspect ratio v/h, Speed, Direction, Color, Object classes (Upright persons, Bikes, Cars, Trucks) based on Duration, Size, Aspect ratio v/h, Speed, Direction, Color, Object classes (Upright persons, Bikes, Cars, Trucks), 3.2 to 10 mm Automatic Varifocal (AVF) lens, MicroSD card slot for edge recording, Motion, tamper and audio detection, FTP, IR range upto 30mtrs Dropbox and e-mail applications, 3 axis adjustment, ONVIF Profile S & G & T, PoE, IP66, IK10, CE, FCC , UL certified. SD card support up to 2TB.

Hard Drive Disk: SITC of SurveillanceHDD 8 TB for 30 days storage at D1 resolution.

55 Inch Professional LED Display , Size : 55 Inch diagonal , Brightness : 440 nits , 4K (3,840 x 2,160), Professional Slim Blade Stand Display with 4K , HDR Processor X1, HDR (HDR10, HLG, Dolby Vision), Direct LED,Dynamic contrast ratio up to 400,000:1,4K X-Reality PROTRILUMINOS PRO technology, 24/7 Portrait ,Tilt functionality, Flexible Content Layout with HTML5, 16GB On Board Storage ,Motion flow XR,HDCP 2.3 (HDMI) / RS232 / USB / RJ45 / Wi-Fi with In-Built Bluetooth / 20W Speakers / Android™ OS system, Viewing angle 178 degree, Pro Mode, Pro Display using Apple Air Play & Chromecast

Supply, Installation, Testing & Commissioning of loaded UTP CAT6 Gigabit modular Patch Panel for 24 ports in 1U form factor, with universal A/B labeling Loaded with suitable monetarization with all necessary accessories to complete connectivity.

Supply, Installation, Testing and Commissioning of 1 mtr. Cat 6 Patch cord.

Supply, installation, testing and commissioning of RJ-45 socket outlet point with suitable Front Plate, CRCA sheet steel box with all necessary accessories & hardware etc. with require all accessories to finish the job

SITC of Wall/Floor mounted network Rack for 19U switch mounting with fixing accessories set.

Supply,Installation,Testing and Commissioning of 3 KVA single phase online UPS model for 60 minute back-up with 8nos 12 volt 42 AH SMF batteries (Quanta/Exide ),including MS Rack and battery interconnector(1 phase in .1 phase out ) as required complete in all respect

Civil Parts Excavation for cable trenches in soft soil, depth upto 1.2 m including dressing of sides lift upto 1.5 m, including getting out the cable/ pipe etc in layers of 20 cm, ramming, watering and disposal of surplus excavated soil as directed, within a lead of 50 metres.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Regional Stone work (machine cut edges) for wall lining,flooring etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : 50 mm thick fine dressed & chamferd stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand), including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone.

Providing, mixing and applying bonding coat of approved adhesive on chipped portion of Stone as per specifications and direction of Engineer-In-charge complete in all respect. Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Comprehensive Annual Maintanance Contract Charges of entire Project for 5 years after successful completion of Defect Liability Period

MIDAS ELECTRICALS PRIVATE LIMITED