Re Construction of Deputy Commissioner Office Leh ( Under SDP ) by way of design , supply, installation testing and commissioning of 01 Nos 08 passenger Lift ( Elevator ) at DC Office

Design, Supplying, Installation, Testing, and Commissioning of the 8 passenger (554 kg) lift system as per the following specifications complete job. (Make: OTIS, kone, Mitsubishi and Schlinder)CAPACITY(kgs) Type MRL SPEED (mps)1 mpsRISE/ Total travel (m)10 m - 15 m (approx)STOPS 3 Stops With (all opening on the same side) DRIVE VF Regenerative (Closed Loop) POWER SUPPLY 400/415 Volts (3 Phase AC) OPERATION 400/415 Volts (3 Phase AC) OPERATION Full collective operation CAR GROUP One car (simplex) MACHINEPM Gearless (Located in shaft on top of guide rails) TRACTION MEDIAFlat Coated Steel Belt/ or as per the specification of manufacturer CAR FINISH ·                  Rear Mid Panels=Stainless Steel#(Hairline) ·                  Rear Corner Panels=Stainless Steel#(Hairline) ·                  Side Mid Panels=Stainless Steel#(Hairline) ·                  Side Corner Panels=Stainless Steel#(Hairline) ·                  Front Panels=Stainless Steel#(Hairline) FALSE CEILING TYPE FLASE CEILING FINISHStainless Steel #304(Hairline) VENTILLATION Cross flow fan 3 HANDRAILS 20 MM RECESS FLOORING CAR DOOR FINISH Stainless Steel # (Hairline) LANDING DOOR SFINISH Stainless Steel #(Hairline) FIRE RATED DOORSFire rating-60mins PIT DEPTH OVERHEAD As per manufacturer design HOISTWAY DIMENSIONS 2100 mm W x 2100 mm CAR DIMENSIONS(WxD) As per the design of the manufacturer and as per the size of the hoist way. CAR & HOISTWAYDOOR TYPE Central opening (CO) doors DOOR OPENING (WxH) MM 800 x 2000mm DOOR OPERATOR DC Door Operator COP COP for stops <= 12(950mm) in SS #4 (Hairline) CAR POSITION INDICATOR Monochrome LCD Blue back ground HALL FIXTURE O2000 Pan type fixture HALL BUTTON ARRANGEMENT LCD Monochrome type Car Chime Grounding switch Automatic rescue operation complete with all panels , batteries etc as required. Voice synthesizer Intercom Audible Car button STANDARD FEATURES FOR THE LIFT MUST BE PROVIDED WITH a) Direction & position indicator in Car. b) Emergency Alarm (battery approved) c) 2-Phase Fireman Drive. d) Hands Free Press and Speak Intercom (two Way). e) Full Height Infra Red curtains. f) Pit Ladder. g) Tubular Handrails on the side wall. h) Signal Fixtures in Stainless Steel Finish. i) Emergency Light with rechargeable batteries. j) Adjustable Guide Shoes. k) Micro movement LED Based Buttons. l) + 10% to – 10% capacity to withstand the voltage fluctuation withstand capacity. m) Load weighing Device. n) Automatic Phase reversal. o) Car door lock as standard (safety feature). p) Manual Rescue Feature. q) Stainless Steel Buttons with White LED LIGHTS. r) Daily automatic Brake Testing (safety feature). s) Stainless Steel Buttons with Braille Operation. t) Landing Announcement System.

B1. SITC of Servo Voltage Regulator filled with recommended oil upto full capacity Type=Fully Automatic Servo Voltage Regulator Rating=50-KVA Input Frequency=45-55Hz Response Time=10Msec Correction Speed=25-65V/Sec Correction Method=Stop less Correction Cooling= Oil Efficiency=Better Than 98% Control Circuit = Fully Automatic Ic Based Solid Stat, Operation= Fully Automatic Suitability= Suitable For3-Phase, Unbalanced Supply, Unbalanced LoadOperating Temperature Ambient=-15 oc To 45 oc Above ADDITIONAL FEATURES= i) High and low voltage cut off system. ii) Over load and short circuit protection iii) Single phase prevention system. iv) Phase sequence change protection. v) Earth fault protection. vi) High grade CRGO lamination. vii) Simple rugged construction. viii)  99.9% pure copper. ix)  High efficiency. x)Negligible wave form and power factor distortion. xi) Smooth and stepless voltage control. Qnty=01 Set APPROVED MAKE SERVOKON, AE, BRENTFORD ELECTRIC

B2. Maintenance free Earthing Long life maintenance free electrolytic earthling system with 10 feet vertical k type copper not less than2” (50.8mm) ID and not less than 0.08”(2.03mm) wall thickness ,which does not require manual addition of water. The system should be corrosion resistant pre-filled with hygroscopic powder and provided with suitable breathing and leaching ports at the ends. Rated for high fault currents basbar rated for 10KA, fault current bus bar connection type as “Terraweld” to with hold temperature of 7000C. The earthling port shall be designed and supplied with poly plastic port cover non conductive, environment friendly and lockable.The job includes Pit digging, installation of the rods, filling earth, leveling and disposal etc. Required size copper/AL strip as per site requirement Qnty: 2Nos

B3. Providing/ Laying Electric Wiring &Lighting Light point shall be provided in the lift well at a space not exceeding 3m. All the light point shall have control with proper switches and conduits. Socket outlets may also be provided at a suitable place for use by the maintenance staff above the ground floor landing Approved Makes Havells, Polycab, KEI.

B4. Providing/ Laying of Armoured Cabling 35-MM2,1100Volt,3.5-corearmoured cable with Aluminium conductor from Main Panel in the control room to the Machine room Panel fixing with proper pvc conduit, brackets/ fasteners etc. and lugs/ thimbling. Qnty= 40 X 3 Mtr Approved Make Havells, Polycab, KEI Supply installation testing and commissioning of GI electrodes chemical earthing with 84mm dia and 3 meter length wit 3 mm thick the electrode should be dipped galvanised and providing and fixing of 75mm*5 mm copper strip as earth electrode complete job

B5. SITC of Electric Control Panel LT CONTROL PANEL: Fabrication, Supply, Installation, Testing and Commissioning of dust, damp and vermin proof free, floor mounted with base channel, Indoor type factory built sheet steel enclosed modular construction panel, suitable for operation on 415±10% volts, 50Hz AC 3phase 4wire system fabricated out of suitable sized square tubular section and covered with CRCA sheet steel of 2mm thick for frame work and covers, 3mm thick for gland plates i/c cleaning &finishing complete with 7 tank process for powder coating in approved shade.All the MCCB up to 250Amp shall have thermal release with adjustable over load, short circuit & earth fault protection, Bus Bar Rating 200A Take Bus-Bar Density:0.8A/mm2 Approved Make L&T, Schneider,Siemens Qnty=01Nos Comprehensive Maintenance for 03 years Comprehensive Maintenance contract of carrying out repair sand providing/fitting of OEM spare parts to keep the elevator in fully operational condition for a period of 03 years after expiry of 12 Months warranty period. ( 2 NOS X 3 YEARS)