SPL REPAIR TO BLDG NO. P-548 (1-6) PERMT OR MD ACCN AT MAP-II OF 14 IDSR AND ROOF TREATMENT AND WALL PANELS IN BLDG NO. P-275, RS AUDITORIUM UNDER GE CLEMENT TOWN

Amount

M&L for Non Skid coloured ceramic tiles 8-9mm thick (square/ rectangular) area of each tiles exc 0.18 Sqm but n. exc 0.38 Sqm (600x600mm) in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:6 including Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M&L for Non Skid coloured ceramic tiles 8-9mm thick (square/ rectangular) area of each tiles exc 0.18 Sqm but n. exc 0.38 Sqm (600x600mm) as in vertical surface such as dado/ skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 to recieve tiles including Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exc 0.11 Sqm but n. exc 0.18 Sqm (400x400mm) in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:6 complete all as specified and directed

M&L for coloured Glazed ceramic tiles in vertical surfaces 300x450x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement over and including 10mm thick rendering or bedding layer of cement mortar 1:4 including, Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M&L for Machine cut Kota stone slab flooring 16-20 mm thick, laid over & including screed bed of 20 mm thick in cement mortar (1:4) and jointed with grey cement slurry mixed with matching shade pigment including rubbing and polishing complete, all as specified.

M&L for Kota stone slab 16-20 mm thick on vertical surfaces like riser of steps, skirting, dado and pillar laid over & including 10 mm thick in cement mortar (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for mirror polishing of old/existing kota stone/granite/marble/stone work whenever required to give high gloss finish to flooring and vertical surfaces of riser of steps , skirting/dado, landing etc complete all as specified and directed.

M&L for brick work with sub class 'B' old size bricks straight or curved on plan exc 6m mean radius built in CM 1:6 including Demolition of brick work or stone masonry built in cement mortar including all quoins, arches, jambs etc complete all as specified and directed

M&L for RCC 1:2:4 type B1 (using 20mm graded stone agg) as in slab and shelves supported on walls including Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

M&L form work to soffits of suspended slab such as roof slab and similar work n. exc 200mm thick (horizental or sloping) rough finished flat surface complete all as specified and directed

M&L for mild steel TMT bars 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L Baroda green marble 14 -16 mm thick (table rubbed and polished) in step, jambs, pillars , window cills, cooking plateforms and the like in CM 1:4 incl pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble including half round moulding and making hole for gas pipe over 15mm thick screed bed in CM 1:6 complete all as specified and directed

Demolition of cement concrete (Un-reinforced) in ground floors and pavings n.exc 15cm thick (above or below GL) complete all as specified and directed

M&L for 75mm thick PCC 1:3:6 type C-1 (Using 20mm graded stone aggregate) as in plinth protection/path and hard standing laid in panels, finish the top surfaces even and smooth complete all as specified and directed

M&L for 15mm thick plaster in CM 1:6 on fair face of brick walls finished even and smooth without using extra cement,including Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed

M&L for preparation of newly plastered surface of wall and applying two coats of internal acrylic distemper including a coat of primer of approved tint over a coat of wall care putty complete all as specified and directed

M&L for complete removal of existing treatment and preparation of old plastered surface by rubbing down, washing and applying two coat of internal acrylic distemper of approved tint over a coat of wall care putty on walls complete all as specified and directed

M&L for 15mm thick plaster in CM 1:4 on fair face of brick walls finished even and smooth without using extra cement plaster of any description including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for 15mm thick plaster in CM 1:4 on fair face of brick walls finished even and smooth without using extra cement including Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for applying two coats of acrylic exterior emulsion paint (Apex) over a coat of primer after preparation of newly plastered/concrete surfaces on wall complete all as specified

M&L for applying two coats of weather proof exterior emulsion paint (Apex) after complete removal of existing treatment including preparation of old plastered/concrete surfaces on wall complete all as specified

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size exc 1.5 Sqm and n.exc 4 Sqm and making good disturbed portion to match existing surfaces complete all as specified and directed

Taking down chowkhats or frames area n. exc 1.50 Sqm each with shutters (without taking off shutters from the frames) and making good disturbed portion to match existing surfaces complete all as specified and directed

M& L Solid (100 mm X 63 mm single rebate) factory made 100% solid WPC brown door frame made from 100% LEAD FREE (single extruded process) material with density 780 Kg / Cum & manufactured by an ISO:9001-2005 certified company, all as per specification drawings as directed by the Engr-in-Charge. the door frame should be water proof, termite proof, fire retardant and having excellent screw holding capacity complete all as specified and directed.

M& L Solid (125mm X 63 mm Double rebate) factory made 100% solid WPC brown door frame made from 100% LEAD FREE (single extruded process) material with density 780 Kg / Cum & manufactured by an ISO:9001-2005 certified company, all as per specification drawings as directed by the Engr-in-Charge. the door frame should be water proof, termite proof, fire retardant and having excellent screw holding capacity complete all as specified and directed.

S&f factory made single extruded WPC (wood polymer Composite) solid both side prelaminated decorative type flush door shutter of size 35 mm thick comprising of virgin polymer of K valve 58-60 (Suspension Grade ) , calcium carbonate and natural fibers (wood powder/rice husk, wheat husk ) and non toxic additives (maximum toxicity index of 12 of 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with SS butt hinges of required size with necessary full body threaded star headed counter sunk SS screws all as specified and directed

S&F 35 mm thick factory made wire mesh solid WPC Prelaminated both side door shutter consisting of Density 650 kg/cum manufactured by an ISO 9001-2015 certified company . Door to be panelled with SS mosquito Mesh and XTN aluminium mesh for additional strength and safety purpose (confirming as per S:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 Nos MS powder coated butt hinges size 100x 25x2mm and 32 mm long steel screw drilled suitable to pass through both the walls of the MS tube. Other hardware should be fixed with 19x 6 mm size steel screws etc, manufacturer's specification complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint to old undecorated wooden surfaces over a coat of pink primer including preparation, over 10cm width or girth complete all as specified

M&L for preparation of old steel surfaces of any description over 10 cm in width or girth and applying two coat of synthetic enamel paint etc complete all as specified and directed.

S&F windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM) and Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 52x 25mm. Outer frame & mullion sections to have rebate for glazed shutters. Fly mesh with 20 mm GI flat beading for provision of guard bars/ grills. Fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap, handles 2nos of heavy duty stainless steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter with 0.36mm dia of wire and 1.40mm aperture. Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 12mm square guard bars with 110mm spacing c/c (Horizontal bay) to be welded on FI 20x6mm around except runner portion complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

S&F compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc built up from tow or more beam or channel sections or angles with plates including all lattice bars, stiffeners, gusset plates conforming to Fe410-W (Gde-E-250) quality-A

S&F welded steel wire fabric weight n. exc 4 Kg per Sqm suitable to weld with steel members complete all as specified and directed.

S&F in repair rotational moulded PVC water storage tank cylinderical, vertical with closed top hoisted and fixed in position tank capacity 500 Ltr with and including PTMT float valve 20mm dia and making connection for inlet and outlet complete all as specified and directed

M&L for preparing new steel and iron surfaces of any description over 10 cm width /girth and applying two coats of synthetic enamel paint of any tint over one coat of red oxide primer complete all as directed

S&F 250mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate

S&F 100mm size stainless steel butt hinges medium weight ISI marked, cold rolled

S&F 200mm long stainless steel barrel tower bolts all as specified

S&F 150mm size stainless steel handles all as specified

S&F in repair 100mm Pvc pipes single socketed in any length with rubber ring joint laid in trenches of floor complete all as specified and directed

S&F in repair 75mm Pvc pipes single socketed in any length with rubber ring joint fixed to walls complete all as specified and directed

S&F PVC 75 mm floor trap plain with grating including jointing with solvent cement complete all as specified and directed

S&F PVC vent cowls 75mm complete all as specified and directed

S&F in repair of sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm and bowl size 410mm x 330mm x160mm complete all as specified

S&F in repair vitreous china water closet Orissa pattern of size 580 X440mm white ISI marked including provn of cement concrete bedding including connections to flushing cistern/pipe and making good disturbed portion to match existing surfaces complete all as specified

S&F in repair vitreous china white wash hand basin flat back of size 550x400mm including CI/MS brackets including cutting for and pinning in brackets but including waste pipe complete all as specified

Suplly only PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action push type with inlet ball valve and float including flush pipe long 32mm dia, ball valve, handle, bracket etc complete all as specified and directed.

S&F in repair 15mm dia brass chromium plated Bib tap fancy type with wall flange complete all as specified .

S& F in repair 15mm dia brass chromium plated pillar tap with fly long swan head screwed for 15mm bore dia of pipe complete all as specified.

S&F in repair 15mm Stop valve angle cock fancy type, chromium plated with long shunk and cup high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified.

S&F in repair chromium plated brass shower roses with or without swivel joints 125mm size including shower arm complete all as specified

S&F in repair PVC connection 15mm bore dia 450mm long with 2 Nos PTMT nuts with washer complete all as specified

S&F in repair 32 mm dia PVC flush pipe of polyethylene of low or high density for WHB, sink, urinal complete all as specified and directed.

S&F in repair 20 mm dia brass CP tubular towel rail D type 600mm long complete all as specified and directed.

S&F 15 mm bore dia of medium grade galvanised steel tubing with all fittings including tank nipple and fixed complete to wall or laid in floor including cutting through walls, floors, etc and their making good with existing surface including, Taking up or down 15mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed.

S&F 15mm bore gun matel globe or gate valve with iron wheel, screwed both ends for iron pipes complete all as specified

S&F 20 mm bore dia of medium grade galvanised steel tubing with all fittings including tank nipple and fixed complete to wall or laid in floor including cutting through walls, floors, etc and their making good with existing surface, including Taking up or down 20mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed

S&F 20mm bore gun matel globe or gate valve with iron wheel, screwed both ends for iron pipes complete all as specified

S&F in repair of 20mm dia stainless steel drapery rod, fancy type, SS knobs and brackets, fixed in any length complete all as specified and directed

S&F 18 mm thick with min density 600 Kg/Cum LEAD FREE PVC Celuka ply of both side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed

S&F 150mm Hasp and staple stainless steel, including bolt to hinge plate and fixed with screws all as specified and as directed

S&F auto closing hinges 35mm of 0 crank ( KH-001) or 8 crank (KH-002) openable at 110 degree for cupboard/kitchen cabinet shutters complete in all respect and fixed in position all as specified

S & F D-type cabinet handles premium quality, stainless steel 304 / gloss chrome / SN finished 150 mm long matt finished complete fixed in position complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in surface channel or drain or benching in manhole complete all as specified and directed

M&L for PCC 1:2:4 type B-1 (using 12.5 mm graded stone aggregate) as in coping and the like including weathering, slightly rounded or chamferred angles and throating, use of formwork straight or curved complete all as specified and directed.

M&L for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitered/stopped ends etc complete all as specified and directed

M&L PCC 1:5:10 type E-2 (using 40 mm graded brick aggregate) as in filling, mass concrete, sunken floor etc including Demolition of cement concrete (Un-reinforced) in ground floors and pavings n.exc 15cm thick (above or below GL) complete all as specified and directed

M&L for 15mm thick rendering in cement mortar (1:3) as in sunken floors mixed with liquid water proofing compound (as per manufacturer's instructions) finishing the surface even and smooth with and including applying two coats of SBR Latex/ Dr Fixit or equivalent on plastered or unplastered surface complete all as specified and as directed.

M & L of water proofing treatment to roof slab with APP based modified polymeric membrane as per manufacturer’s instructions with following course of description below :- (a) Removal of existing roof treatment i.e APP membrane including plaster, PCC padding, brick tiling incl mud mortar and open up RCC roof slab including picking, sweeping cleaning with wire brush and washing down with water to remove dust, dirt to get surface free of laitance, scales, oil or any other loose material (b) One coat of cement slurry admixed with acrylic bonding compound SBR Latex liquid polymer as to be used for bonding of new concrete / mortar to old surface as per manufacturer direction and finishing the surface even and fair (without using extra cement) as in roof padding to receive roof treatment (c) Applying a priming coat of bituminious primer @ 0.30 Kg /Sqm, till the surface is properly impregnated. (d) Providing APP based 5 layer polymeric membrane minimum weighing 3.6Kg/ Sqm and minimum 3 mm thick reinforced with polyester non-woven fabric (weight not less than 150 gms/sqm) centre core, laid on primed surface by forced applications as per the manufacturer's instructions with side over lap of 75 mm and end overlap of 100 mm. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer (torching overlap by propane or butane gas torch ) and sealing it with the help of hot trowel. The overlap joints shall be made as a monolithic layer. (e) Apply two coat of bituminous aluminium paint @ 0.20 Kg / Sqm each coat over APP membrane. Note : The work is required to be executed at single, double & triple storey buildings (accesible & non accesible). Rate for the same is included.

M & L PCC 1:2:4 type B-0 (using 12.5 mm graded stone agg) mixed withliquid water proofing compound (as per manufacture direction and paid separately) over and incl one coat of cement slurry admixed with acrylic bonding compound SBR Latex liquid polymer as to be used for bonding of new concrete / mortar to old surface as per manufacturer direction and finishing the surface even and fair (without using extra cement) as in roof padding incl removal of existing padding, cleaning, washing & rubbing the surface complete all as specified and directed. Note : The work is required to be executed at single, double & triple storey buildings (accesible & non accesible). Rate for the same is included.

Demolition of brick work or stone masonry built in cement mortar including all quoins, arches, jambs etc complete all as specified and directed.

M&L brick work with sub class "B" old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

S&F‘’ Woodlot’’ FR Grades 2430x131x16mm made of exterior grade HDF backed with acoustical Fleece providing sound absorption of 0.60 NRC as per ISO 354.To be installed with 15mm Aluminium profile conforms to Aluminium Alloy 6063-T 6.Temper As per BS:1474-1987 and G.I Lock in clips on the back of tongue and Groove system. The density per panel is 750-800 kg/m3.The panels come with tongue & groove for seamless patterns,4-28mm Groove and visible panel. These slats are made from acoustical fibreboard with linear perforations for excellent uniformity. The perpendicular holes are available on the back of panel which are covered by black acoustical fleece. Achieves sound reduction of 0.60 NRC. To be installed directly on walls with Gypsum Screws., complete all as specified and directed.(Ht Upto 10 Mtr including all necessary scaffolding)

Taking down carefully and Refixing on another place of wooden wall panels perforated any size including all fittings, complete all as specified and directed.Note;-Ht Upto 10 Mtr including all necessary scaffolding)

Taking down cement plaster of any description on brick work or stone masonry walls including rackingout joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L 15mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L 15mm thick rendering cement mortar (1:4) on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed.

M&L 5mm thick rendering in ceiling of cement mortar (1:3) on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed

M & L three coats of whitewashing to newly plastered surfaces of ceilings after preparation of surfaces.

M&L for applying Two or more coats new/old of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S & F Framed work Fe-290(Gde E?165) as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete, drilled for fixing of steel or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

Dismantling asbestos cement (corrugated, semicorrugated etc) sheets in roof coverings including ridges etc complete all as specified and directed

S & F, Pre- painted galvanium aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and as directed.

S&F pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge , Gutter, Gable flashing, corner flashing etc, fixed with self tapping screws as specified and directed.

Demolition of cement concrete (Un-reinforced) in any position n.exc 15cm thick (above or below GL) complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with screw

Supply and fixing of armstrong ceiling system with fine fissured edge tiles acoustical Fleece providing sound absorption of 0.60 NRC having humidity resistance (RH) of 95%, NRC 0.34 light reflectance approx 84% Thermal conductivity K=0.052 - 0.057. W/mk colour white fire performance of class-I as per BS 476 part 6 & 7 in module size of 600 x 600 x 16 mm thick suitable ofr green building appliation with recycled content of 38-41% with Armstrong silhouette profile exposed grid system with 15 mm white flanges incorporating 6 mm central reveal in white/black colour. Silhoutte, main runners & cross tees to have mitred ends & birdsmouth notches to provide mitred cruciform junctions. The Tee sections have a galvanising of 170 gms per sqm & passed through 500 hrs of salt test. The main runner spaced at 1200 mm c/c should be securely fixe to the structural soffit using Armstrong suspension system at 1200 mm maximum c/c. The first/last Armstron suspension system at the end of each main runner should not be greater than 450 mm from adjacent wall. Cross Tees 1200 mm long should be interlocked between main runners at 600 mm c/c to form 1200 x 600 mm module. 600 x 600 mm module is fortned by fitting 600 mm long flush fitting cross Tees, Perimeter trim consist of Armstron wall angles of size 3000 x 19 x 19 mm secured to walls screws at 450 mm c/c (Ht Upto 10 Mtr including all necessary scaffolding)

Cutting chases, pinning in brick or concrete wall and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

Chipping of unsound /weak concrete materials including cover plaster from RCC structural member i.e. slabs , beams, columns ,lintel,chajja, fin , facia etc. 50 mm average thickness including tapering all edges, making square shoulders of cavities air or sand blasting etc and cleaning of exposed concrete surface of lightly picking materials by air blasting or sand blasting including foreign materials , loose concrete/aggregate etc and disposal of all debris out side of MOD land and complete all as specified and as directed by Engr-in-Charge.(Any storey/ height of building/ structure)

Taking down existing tar felt and Pcc,plastering from the roof surface washing down and cleaning the surface with water and rubbish off the premises and M&L 25mm thick Pcc 12.5 mm graded aggregate B0 for finshing existing surface even & smooth and laying water proofing treatment to the Roof with single component, cold applied, water based Polyurethane modified acrylic dispersion with highly elastic and UV resistant water proofing treatment to the Roof @ 1.2kg/per sqm to confirms to ASTM D 6083- 97a with a density of 1.25 to 1.3kg/per ltr, having tensile strength of 1.5N/mm2, having elongation of 350°/o with solid content not less than 60% in 2 coats including self-priming bond coat of Advanced Latex plus mixed Water and Cement in 1:4:7 and sandwiching 40gsm Geo-textile between two coats. The finished cost to include surface preparation, making coving at Junction, Bore Packing, treatment of construction joints completely as per specification and direction of the Engineer ln charge.(Ht Upto 10 Mtr including all necessary scaffolding)

Taking Down any dia r including fiting spigot and socket ends and lead joints including burning out joints and recovering lead.

S & F 75 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including all fittings like bend and shoe

S & F 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including all fittings like bend and shoe

S & F 160 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in wall or in floors including all fittings like bend and shoe.

Dismantling water tanks and Refixing in same position complete all as specified and directed.

S&F PGB Assembly sensor for urinal complete

M & L three coats of whitewashing to new plastered surfaces of walls after preparation of surfaces.

M & L three coats of whitewashing to newly plastered surfaces of ceilings after preparation of surfaces.

M&L for preparation of old decorated surfaces of wood and wood based materials, wooden, plastered, concrete surfaces of any descriptions not otherwise described over 10Cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing new steel and Iron surfaces of any description over 10 cm Width /Girth and applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces complete all as specified and directed.

M&L for preapration of old concrete surface or unplastered surafces on wall with two coats of oil bound distemper on wall surfaces over a coat of putty complete all as specified and directed by Engr-in-Charge. (Ht Upto 10 Mtr including all necessary scaffolding)

Disconnecting the electrification and taking down DBs (any type of SPN DBs) and making good to the disturbed surfaces to match the existing surface all as specified and as directed by EIC. Note - Temporary power supply shall be provided by contractor.

Taking down U/S submain wiring aluminium etc and making good the disturbed surfaces of walls/ floor etc matching with the existing surface.

M&L for sub-main wiring (concealed) with two single core 4 sq mm FRLSH PVC insulated unsheathed stranded copper conductor cable drawn through including chasing cutting in any type of massinory including 20 mm dia non-metallic PVC conduit fixed in wall including 4 sq mm copper earth continuity wire, accessories and connecting to earth dolly complete, all as specified and as directed by EIC.

M&L for sub-main wiring (concealed) with two single core 6 sq mm FRLSH PVC insulated unsheathed stranded copper conductor cable drawn through including chasing cutting in any type of massinory including 20 mm dia non-metallic PVC conduit fixed in wall including 6 sq mm copper earth continuity wire, accessories and connecting to earth dolly complete, all as specified and as directed by EIC.

Taking down carefully aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pedants, regulators, sockets, light fitting etc.. and making good the disturbed surfaces of walls/ floor etc matching with the existing surface all as specified and as directed by EIC.

Material & Labour for following type Point Wiring controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with contineous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed PVC conduit MMS ,duly concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia (Color coding of wires shall be Phase, neutral and earth wire all as specified ) sunk Metal flush box with and incl decorative polycarbonate frame for housing Modular Switches, sockets , fan regulators etc including white cover cover plate complete all as specified and directed. Note:- i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates).

One light point controlled by one switch.

One ceiling fan point controlled by one switch.

One exhaust fan pointcontrolled by one switch.

One 3 pin socket outlet 5 Amps on the same board.

One 3 pin socket out let 5 Amps on the independent board.

One bell point controlled by one bell push

All as per item No 109 above but one light point controlled by two, 02-way point wiring with two no of two way switch with cables 1.5 sqmm size in PVC conduit

All as per Item No. 109 above but 2.5 Sq mm multi stranded copper conductor with 2.5 Sq mm copper earth continuity wire connected to earth duly complete for one 15A Socket on Independent board all as specified and as directed by EIC.

S&F LED tube light batten 20 watts 4 fts polycarbonate housing, translucent diffuser with LED light source , 2200 lumen, natural white ,surge protection range 2KV, voltage protection range 120-280 VAC , system efficacy not less than 110 Lm/watt for the fitting , power factor>0.95 total harmonic distortation<20% , colour rendering index >80, coefficient colour temp 6500 K, fixed on site with all accessories with connecting suitable size of 3 core flexible cable all as specified and directed.

Removing & Refixing serveceable tube light fittings with connection from ceiling rose incl testing complete as directed by EIC

S & F angle lamp holder, PVC Polycab type with back plate suitable for batten fittings complete including fixing of 9/10 watt LED bulb all as specified.

S&F Oval shape Bulk head Edge -lit LED fitting comprising with high brightness LED 10 WATT,IP-67 protection all as directed.

S& F 10 Watt LED light fitting mirror type with high out put diffuser 2 feet 220 VAC decorative type complete all accessories with connecting suitable size of 3 core flexible cable as specified and as directed.

S & F Switch Modular single pole, one way 6 Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge.

Supply and fixing modular switch type 2 way 06 Amp, 1 Module, 240 Volts AC. Make Legrand Cat No -673402 or equivalent in Havells/Cona.

Supply and fixing modular socket, 6A -2/3 pin combined 2 module ISI marked 230 volts, 50 Hz all as specified and directed by Engr- in-charge.

Supply and fixing modular socket, 6A/16A -2/3 pin combined 2 module 230 volts 50 hz all as specified and directed by Engr- in-charge.

Supply and fixing switch modular , one-way 16Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge.

S & F Switch Modular bell push single pole, one way 6 Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge.

Supply and fixing door bell ding dong type suitable for 230 Volts, AC, 230 Volts, single pole.

M & L for ceiling rose, surface bakelite, 65 x 50 mm, three terminals all as specified and as directed.

S & F sheet metal enclosures for SPN DB's with double glazed door for incorporating MCBs,IP-43 , 8 way with 100 amps rated busbar, 240 volts, as per IS-8623 all as specified and as directed.

S & F MCBs SPN 32 amps, 240 volts, 50 Hz, 'C' curve including necessary incoming and out going electric connection with suitable size of copper lugs all as specified and as directed by Engr-in-Charge.

S & F MCB SP, 5-32 Amps, 240 volts, 50 Hz, 'C' curve including necessary incoming and out going electric connection with suitable size of copper lugs all as specified and as directed by Engr-in-Charge.

S&F DB Power unit MCB protected socket with sheet steel enclosure 20 Amp combo incl 16 amp plug top indicator type for A/C or Geyser

S & F decorative type Glaze Wall light inclding 7/9 watt LED (B22) with all necessary fittings complete all as specifed and directed.

Removing the serviceable water storage Geyser of cap 25 Ltre carefully and Refixing the same after overhauling with descaling and painting as directed

Removing the serviceable Exhaust fan, steel body carefully and refixing the same after overhauling with greasing,oilingand painting as directed .

Taking down ceiling fan from existing building and again refixing the same ceiling fan after oiling / greasing complete, connecting up including provision of cable flexible 3 core of suitable size wire from ceiling rose to connect fan.

Supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230 volts, 50 Hz, 1200 RPM, copper winding of sweep 250 mm complete all as specified and directed.

S& F Ceiling fan complete with copper winding ,blades ,down rodss,electronic regulastor and accessories 230 v0lt,1200mm sweep,min delivery 210/215 CFM with service value 6.00 , BEE. Five star rated with BLDC complete all as specified and directed.

M & L for LED Bldg Security light Supply and fixing LED street light fitting 45 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete with st lt bracket ,made out of 1.0 mt long,32mm dia incd clamps 40x6mm flat incl painting as directed by Engr-in-charge

NOTES :- 1. For the items for which specifications not mentioned any where in the tender, the BIS specifications shall be followed.

JBN CONSTRUCTION (BID ID -3342434)

RAMAPATI ENGINEERING SERVICES (BID ID -3352856)