Loading
Loading…
Loading…
Tender Value
₹5.2 Cr
EMD Value
₹4.1 L
Closing Date
6 Mar 2026, 3:30 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
DRM/WORKS
14 conditions · 2 needing a document upload
10.2 - Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees. N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, as provided at Page 41 of tender documents, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
10.1 Technical Eligibility Criteria: (a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b) (1)In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii)One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre- defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Non-submission of the Completion certificate issued by the Competent Authority shall result into summarily rejection of the offer.
Defination of Similar Work :- 1.1 - Any P. Way works
23 conditions · 2 needing a document upload
"The said suppliers of goods and/or services would be subject to GST Act and Rules as applicable from time to time. Tenderers are requested to submit their offers as per GST Tax regime. All the bidders/tenderers should ensure that they are GST compliant and their quoted tax structure/rates are as per GST Law"
Successful tenderers are required to submit the number of labour to be employed for this particular work. Also the list showing names, along with all other details, of male and female workers employed in this work, should be submitted to office, at the time of submitting performance guarantee and before executing contract agreement. They should also ensure that 1) The payment to the contract labour should be made through bank/cheque. 2) Identity Cards should be issued to all contract workers. 3) Necessary steps should be taken to deduct provident fund from the payment made to contract labour and ensure that the same is credited to their Provident Fund account. 4)Medical facilities from ESI should be ensured, if applicable.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tenderers are required to submit a copy of cancelled cheque in order to facilitate the payments regarding refund of EMD etc. in their proper accounts.
In addition to latest provisions of GCC, and all contents of tender documents, all other latest instructions of Railway Boards issued vide various letters received from time to time on concerned matters and related to tender, will also be applicable for the tenders as per necessity and tenderers have to co-operate with Railways and ensure the compliance
Indian Railways Standard General Conditions of Contract, April 2022 (GCC, April 2022) has been introduced and available on website with all correction slips issued up to date for inviting tender and same will be applicable for this tender. Advance Correction Slip No. 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10 to Indian Railways Standard General Conditions of Contract, April - 2022 circulated by the Railway Board vide letter No. 2022/CE-I/ CT/GCC-2022/Policy dated 14.07.2022, 13.12.2022, 26.04.2023, 07.08.2023, 20.10.2023 , 21.12.2023, 25.09.2024, 20.12.2024, 09.01.2025 and 04.03.2025 are applicable to this tender. Tenderers are requested to download the same from the railways website and ensure the implementation of the latest provisions made in GCC while execution of work. After that, if any latest correction slip issued by Railway Board on any matter, will also be applicable with immediate effect, though not mentioned in original tender document.
I/We agree to carry out all works with use of modern equipments of required capacity for the work without extra payment. The decision of railway engineer shall be final and binding in this regard.
It is the responsibility of contractor to arrange the payment of the labour employed for the work through bank and to deduct PF as per the provisions of Minimum Wages Act.
The quantities shown above are approximate and to give a general guideline. Railway reserves a right to increase, decrease or to delete any of the items mentioned in schedule.
As per ACS 1 to GCC April 2022, issued vide Railway Board's letter dt. 14.07.2022, PVC Clause shall be applicable only in tenders having advertised value above Rs. 2 Crores provided to the provisions as per clause 46A-1. Tenderers should take a note and quote their rates accordingly.
In case Civil work tenders, the quantity of cement required in the items where necessary, will be used by the contractor on the same rates as accepted in tender, as per the quantity mentioned against each item in USSOR/DSR, though not mentioned in tender schedule.
Tenderers are advised to quote their rates including all type of taxes and levies etc. to be paid by them. Any extra payment will not be made on account of taxes/Levies etc., in excess of Contract Agreement Value,
In case of submission of Bid Security in the form of Bank Guarantee, a scanned copy of Original BG valid for a period of 90 days beyond the validity period of tender, and addressed in favour of Sr. DFM/WCR/BPL, shall be uploaded on IREPS portal while applying for tender. And As per ACS 2 to GCC April 2022, circulated vide Railway Board letter dt. 13.12.22, original BG should be delivered in person to the Concerned Official in Office before closing date for submission of bid (i.e. Excluding the last date of submission of bid) without fail. Any failure in this connection shall lead to summary rejection of bid.
TSR(P) 7.317 Kms, TRR(P) 26.810 Kms & TFR 22.716 Kms in Itarsi-Bina & Maksi- Bhopal section under Sr.DEN/C/Bhopal section.
WCR-BPL-W-25-26-C-39-153~WCR
WCR-BPL-W-25-26-C-39-153
Open
Works - General
12 Months
Bhopal, Madhya Pradesh
₹0
₹4.1 L
6 Mar 2026
12 Feb 2026
20 Feb 2026
93 items across 4 schedules · ₹6,36,61,584.08 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Using Soil Class SQ1 | cum | 20000.00 | 345.64 | 69,12,800 |
| 2 | Up to 40 m long rail panel | RM | 3125.00 | 9.6 | 30,000 |
| 3 | More than 40 m long rail panel | RM | 52000.00 | 15.18 | 7,89,360 |
| 4 | Extra to Item no. 061011 for working on bridge | RM | 500.00 | 4.19 | 2,095 |
| 5 | Extra to Item no. 061012 for working on bridge | RM | 1950.00 | 6.97 | 13,591.5 |
| 6 | For Through Rail Renewal work | TRM | 26000.00 | 47.04 | 12,23,040 |
| 7 | For Casual/Scattered Rail Renewal work | RM | 2975.00 | 37.25 | 1,10,818.75 |
| 8 | For Through Rail Renewal work | TRM | 26000.00 | 48.48 | 12,60,480 |
| 9 | For Casual/Scattered Rail Renewal work | RM | 2975.00 | 39.44 | 1,17,334 |
| 10 | For PSC wider base sleepers - For location of work not involving deep screening | Each | 15000.00 | 375.18 | 56,27,700 |
| 11 | Locations other than Ballasted Deck Bridge | Each | 1895.00 | 496.88 | 9,41,587.6 |
| 12 | Through Fitting Renewal (TFR) on PSC track, comprising of renewal of Grooved Rubber Pads, Liners and ERCs without damaging PSC sleepers. Scope includes removal of all fittings, cleaning of rail seat, rail flange at liner seats, and eye of Inserts with wire brushes and applying Grease Graphite Grade "O" (IS:408) to eye of insert and central leg of ERC with contractor's grease of Railway's specification, fixing all fittings in correct position and sealing liner edges with grease all complete including collection and stacking of released materials at nominated locations within SSE Jurisdiction as directed by Engineer-in- Charge. Note: All the fittings will be supplied at SSE/Stores/Depot. | Sleeper | 49860.00 | 36.22 | 18,05,929.2 |
| 13 | Lubrication of Elastic Rail Clips on PSC sleepers with contractor's grease, conforming to Railway's specifications, labour etc. complete as per procedure prescribed in latest edition of IRPWM. | ERC | 475000.00 | 4.6 | 21,85,000 |
| 14 | Removing seized ERC from SGCI inserts of existing track by using suitable approved chemicals and re-fixing after greasing of insert eye and ERC with Contractor's grease of specified quality as per provisions of IRPWM, as directed by Engineer in-charge. Note: 1.List of Seized ERC along with location shall be prepared after inspection of SSE/P.Way and marked prior to execution of this item. 2. Due care shall be taken to avoid any damage to the sleeper 3.A penalty of 50% of the basic cost of new sleeper in nearest sleeper factory shall be levied on each, if SGCI insert is broken or sleeper gets cracked in the process. | ERC | 4000.00 | 58.59 | 2,34,360 |
| 15 | Lubrication of gauge face of rail on curves, cross overs, points & crossings, turn-in curves and at locations as required with contractor's grease graphite grade "O" IS 408 and as directed. | RM | 150000.00 | 6.13 | 9,19,500 |
| 16 | By using Railway's Grease graphite | Each | 12500.00 | 32.35 | 4,04,375 |
| 17 | Renewal of seized Plate/Rail screws on PSC Sleepers by using gas or any approved methods, duly drilling holes in broken screw and removing existing screw pieces from the holes along with existing dowels and fixing new contractor's dowels (procured from RDSO approved sources) and grouting around dowel with Epoxy materials of approved specification and refixing new Railway's rail/Plate screws duly greasing the screw w i t h specified grease with all contractor's materials, consumables, tools & plants, labour with all lead, lift. Note: 1.Seized screws shall be identified and marked by JE/P.Way and verified at minimum SSE/P.Way In charge) level. 2. Due care shall be taken to avoid any damage to the sleeper 3.A penalty of 50% of the basic cost of new sleeper in nearest sleeper factory shall be levied on each, if sleeper gets damaged in the process. | Each | 1250.00 | 428.9 | 5,36,125 |
| 18 | Rail section of 52Kg and above | Each | 4260.00 | 152.2 | 6,48,372 |
| 19 | Renewal of existing SEJ along with PSC sleepers under traffic block conditions as per approved drawing including fixing of special size bearing plate, rubber pad and other sleeper / rail fittings, greasing to the fittings, leading all new materials to site, transportation of released materials within a lead of 250m, cutting of Rails, drilling of holes, fixing of related fittings, providing temporary connection with fishplates till welding of SEJ is done and sleepers shall be given initial packing to make track fit for 20KMPH speed. Note: (1) Rail cutting and hole drilling shall be paid separately. (2) One set comprise complete SEJ on both rails at SEJ. | Set | 20.00 | 8,312.34 | 1,66,246.8 |
| 20 | For 1 in 12 Turnouts (Sleeper No 1 to 25 and 5 approach sleepers) | Set | 40.00 | 1,885.64 | 75,425.6 |
| 21 | For 1 in 12 Lead portion (Sleeper Nos 26 to 64 & 74 to 83 and 8 approach sleepers) : | Set | 40.00 | 4,804.98 | 1,92,199.2 |
| 22 | For 1 in 12 Turnouts (Sleeper No 65 to 73 ) | Set | 40.00 | 1,403.99 | 56,159.6 |
| 23 | Depth of 300 mm below bottom of sleeper - For Plain Track : | TRM | 2500.00 | 609.95 | 15,24,875 |
| 24 | Depth of 300 mm below bottom of sleeper for Turnouts | TRM | 500.00 | 975.91 | 4,87,955 |
| 25 | For average lead up to 50m and lift up to 5m | cum | 2500.00 | 113.06 | 2,82,650 |
| 26 | Boxing and profiling of ballast as per procedure prescribed in latest edition of IRPWM including cess dressing on both sides of track. The work will include removing excess ballast from track and putting the same in crib and shoulder by leading to a maximum of 50m including crossing of track, deweeding on ballast section etc and as directed by Engineer-In charge. | TRM | 75000.00 | 27.59 | 20,69,250 |
| 27 | Using H3C electrodes | Each | 15.00 | 8,773.53 | 1,31,602.95 |
| 28 | Using H3C electrodes | Each | 15.00 | 10,120.16 | 1,51,802.4 |
| 29 | For PSC Sleeper Track with Sleeper Density of 1660 | TRM | 8000.00 | 144.51 | 11,56,080 |
| 30 | For PSC Sleeper Track with Sleeper Density of 1660 | TRM | 8000.00 | 111.16 | 8,89,280 |
| 31 | For PSC sleeper Track with Sleeper Density of 1540 sleepers/Km or more | TRM | 10000.00 | 186.72 | 18,67,200 |
| 32 | Without Rail tensor | TRM | 50000.00 | 50.9 | 25,45,000 |
| 33 | One mobile Gang comprising of 15 physically fit labours plus 1 Mate. Note: (1) In case, contractor provides less no. of Labour/Mate or for non availability of vehicle, payment will be deducted for each such person or non-availability of vehicle @ 20% of the accepted item rate, separately for each shortfall. (2) The Contractor shall keep one pick up Truck of minimum 1.5T payload capacity with Driver all the time and all expenditures for running at an average of 80 kms per day shall be born by the Contractor. | Gang Day | 100.00 | 14,664.51 | 14,66,451 |
| 34 | Replacing existing glued joint rail with cut rails or with glued joint rail or insertion of glued joint by cutting existing track under traffic condition by cutting rails, refixing with all rail sleeper fastenings and providing required gaps for carrying out welding as an alternative to drilling holes or joining rails with fish plates duly drilling holes as required including stacking of released material and as directed by engineer in-charge. Note: (1) Drilling holes & rail cutting will be paid separately. (2) Transportation of materials to the site of work from supply points, if more than 250m, shall be paid separately. | Each | 50.00 | 1,884.92 | 94,246 |
| 35 | Removing weeds & bushes in ballast section and cess up to 3.95m from centre line of track in mid section & station yard, as specified by Engineer in-charge including disposal of branches, bushes outside cess/yard. | TRM | 150000.00 | 15.62 | 23,43,000 |
| 36 | Trimming of tree branches coming within 6m of centre line of track & those obstructing views of Curves/LCs / Signal / Indicator at locations in section & station yard, as specified by Engineer in-charge including disposal of branches, bushes outside cess/yard. Note: Girth of more than 20 cm will only be considered as tree branch. | Each | 50.00 | 179.77 | 8,988.5 |
| 37 | For 60 Kg Rails | RM | 50260.00 | 59.67 | 29,99,014.2 |
| 38 | For day time block working | TRM | 140000.00 | 19.88 | 27,83,200 |
| 39 | 60 Kg - 110/90 UTS - Outside Track | Each | 200.00 | 261.75 | 52,350 |
| 40 | 60 Kg - 110/90 UTS - On Running Line | Each | 450.00 | 331.17 | 1,49,026.5 |
| 41 | Outside Track | Each | 350.00 | 53.95 | 18,882.5 |
| 42 | On Running Line | Each | 850.00 | 71.32 | 60,622 |
| 43 | Drilling holes of specified size for bond holes with 7.2mm dia drill twist to correct spacing and location on 60kg/52kg rails on cess or under traffic block with contractor's tools and plant, equipment, consumable, labour etc complete as directed by the Engineer in charge at site. | Each | 450.00 | 39.72 | 17,874 |
| 44 | Sleeper Spacing, Re-spacing / Squaring of sleeper by Hydraulic Sleeper Spacer with contractor's tools & plants, equipment, consumable with all lead & lift etc. complete, as directed by Engineer in- charge. Hydraulic Sleeper Spacer shall be as per RDSO's Specification No. TM/SM/17, dated 31.03.1992. | Each | 2500.00 | 86.6 | 2,16,500 |
| 45 | Drilling of holes (vertically) of required size into concrete sleeper in-situ for fixing guard rails and check rails on concrete sleeper track at specified locations by concrete sleeper drilling machine with contractor's tools & plants, equipment, consumable with all lead & lift etc. complete, as directed by Engineer in- charge as per RDSO's Specification. | Each | 500.00 | 110.58 | 55,290 |
| 46 | I n Wagon where mechanical handling is possible and traffic block is not required or in Truck/trailer. | MT | 145.00 | 136.44 | 19,783.8 |
| 47 | I n Wagon where mechanical handling is possible and traffic block is not required or in Truck/trailer. | MT | 500.00 | 134.38 | 67,190 |
| 48 | For lead up to 500 metre. | MT | 100.00 | 403.67 | 40,367 |
| 49 | For lead beyond 500 metre and up to 1 Km. | MT | 75.00 | 520.17 | 39,012.75 |
| 50 | From Wagon where mechanical handling is possible and traffic block is not required or in Truck / trailer. | MT | 150.00 | 100.82 | 15,123 |
| 51 | During period of traffic block | MT | 3200.00 | 30.73 | 98,336 |
| 52 | I n Wagon where mechanical handling is possible and traffic block is not required or in Truck / trailer | MT | 500.00 | 106.6 | 53,300 |
| 53 | For lead up to 500 metres | MT | 6475.00 | 314.3 | 20,35,092.5 |
| 54 | For lead beyond 500 metre and up to 1 Km | MT | 2195.00 | 465.38 | 10,21,509.1 |
| 55 | Lead up to 5 Km | MT | 95.00 | 175.92 | 16,712.4 |
| 56 | Lead beyond 30 Km and up to 50 km | MT | 300.00 | 443.4 | 1,33,020 |
| 57 | Lead beyond 100 Km and up to 150 Km | MT | 420.00 | 973.94 | 4,09,054.8 |
| 58 | Extra for every Km per MT beyond 150 Km over item no. 172047 | MT-Km | 18000.00 | 3.25 | 58,500 |
| 59 | Lead beyond 100 Km and up to 150 Km | MT | 4000.00 | 851.96 | 34,07,840 |
| 60 | Extra for every Km per MT beyond 150 Km over item no. 172057 | MT-Km | 80000.00 | 3.25 | 2,60,000 |
| 61 | From Truck / Trailer | MT | 130.00 | 98.23 | 12,769.9 |
| 62 | From Truck / Trailer | MT | 585.00 | 138.77 | 81,180.45 |
| 63 | Rails, switches, crossings, SEJ, Glued Joints, Check Rails etc. | MT | 2500.00 | 410.31 | 10,25,775 |
| 64 | All type of PSC sleepers | MT | 6250.00 | 447.11 | 27,94,437.5 |
| 65 | P.Way fittings of all types and other similar loose items | MT | 100.00 | 406 | 40,600 |
| 66 | Level crossings with asphalted road surface | Sqm | 550.00 | 600.77 | 3,30,423.5 |
| 67 | Drilling of 25mm to 40mm dia. holes in PSC sleepers with suitable rotary hammer / drilling machine at indicated location for fixing of guard rails on bridges & its approaches as per approved drawing and fixing of contractor's HDPE dowels and adhesive of approved quality to Drawing no. RDSO/T-3002, procured from RDSO's approved sources with contractor's materials and consumable. | Each | 250.00 | 386.32 | 96,580 |
| 68 | Renewal of existing guard rails of all rail sections on bridge portion over wooden/PSC/steel channel sleepers excluding flared ends duly leading new guard rails including cutting of rails, drilling holes to the guard rails as required and as per drawings, refixing with all fastenings, and leading back the released rail, stacking at nominated place clear of infringements with all leads & lifts complete and as directed. | TRM | 800.00 | 238.75 | 1,91,000 |
| 69 | Manufacture & supply of wire brush 25mm long, as directed by Engineer in-charge. | Each | 100.00 | 55.64 | 5,564 |
| 70 | Supply of Used Lubricating Oil of approved quality | Litre | 300.00 | 58.29 | 17,487 |
| 71 | For erection | Each | 150.00 | 268.32 | 40,248 |
| 72 | For removal | Each | 150.00 | 218.08 | 32,712 |
| 73 | Providing and fixing Trolley Refuge of size 3.0m x3.0m on cess, placing with released unserviceable PSC sleepers and keeping them at all four sides of refuge and also placing as matting inside the refuge by keeping them in upside down position with a minimum of 14 sleepers including levelling with earth, excavation, all lead and lift, crossing of tracks, leading the sleepers with in a free lead and lift, handling etc., with all contractor's men material complete and as directed by the Engineer-in-charge. Note: Earth-work will to be paid separately under relevant item. | Each | 100.00 | 4,292.55 | 4,29,255 |
| 74 | JCB Backhoe Loaders 3DX Plus or similar with minimum 1.10 cum bucket capacity | Hour | 1000.00 | 830.66 | 8,30,660 |
| 75 | Hydra or similar tyre mounted Pick-n-Carry crane of 12T capacity for misc. works of handling of material | Hour | 500.00 | 1,123.37 | 5,61,685 |
| 76 | Tractor with Trolley for local transportation or other misc. works. | Hour | 800.00 | 291.34 | 2,33,072 |
| Schedule total | ₹6,00,21,930 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .