Construction of District Registration Office Arwal under Arwal district including electrical work For The Year 2026-27.

Earth work in excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m . including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Excavating, supplying and filling of local earth (including royalty but excluding cairriage cost) by mechanical transport upto a lead of 3km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. If local earth is available at more than 3 km lead the actual lead must be approved by compitent authority. cairraiage of material will be paid seperately and calculated after deducting initial lea

Extra for every additional lift of 1.5 m or part thereof in :

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Providing designation 100 A one brick on edge soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/

Providing and laying in position cement concrete of specified grade 1:3:6exluding the cost of centring and shuttering-all work upto plinth level

Providing and laying in position cement concrete of specified grade 1:2:4exluding the cost of centring and shuttering-all work upto plinth leve

1:1.5:3(1 Cement :1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth leve

1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources

All works up to plinth level

All work above Plinth level upto floor V Level.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete

Thermo-Mechanically Treated bars TMTC-500-8mm dia.

Thermo-Mechanically Treated bars TMTC-500-10mm dia.

Thermo-Mechanically Treated bars TMTC-500-12mm dia.

Thermo-Mechanically Treated bars TMTC-500-(16-25)mm dia.

Brick work with FLY ASH bricks in foundations and plinth in :

Cement mortar 1 .:4 (1 cement: 4 coarse sand )

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :

Cement mortar 1:6 (1 cement: 6 coarse sand )

Extra tor Brick work in superstructure above plinth level upto floor V

Brick work with bricks of class designation 100A in foundations and plinth in :Cement mortar 1:6 (1 cement: 6 coarse sand )

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :Cement mortar 1.:4 (1 cement: 4 coarse sand )Extra tor Brick work in superstructure above plinth level upto floor V

Centring and shuttering including strutting,propping etc. and removal or form work for

Centring and shuttering including strutting,propping etc. and removal of form for

Foundations, footings, bases of columns etc. for mass concrete

Lintels, beams, plinth bams, griders, bressumers and cantilevers.

Columns,Pillars, Piers, Abutments, Posts and Struts

Stairs,(excluding landings) except spiral-staircaces.

Weather shade,Chajjas, corbels etc. including edges

Suspended floors, roofs, landings, balconies and access platform with water proofply 12 mm thick.

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick

Providing and laying Ceramic glazed floor tiles 300x300 mm (thicknessto be specified by the manufacturer) of ist quality conforming to IS :15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqmincluding pointing in white cement mixed with pigment of matching shade complete.

Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength,thickness & size/shape, made by table vibratory method , to attain superior smooth finish using PU or equivalent moulds, laid in required Grey colour & pattern over 50mm thick compacted bed of coarse sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks,lawns, drive ways or light traffic parking etc. all complete as per manufacturer’s specifications & direction of Engineer -in-Charge

Providing and laying vitrifed floor tiles in different sizes {thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching etc., complete.

Size of Tile 60x60 cm

Providing and laying Vitrified tiles in different sizes (thickness to bespecified by manufacturer), with water absorption less than 0.08 % andconforming to I.S. 15622, of approved make, in all colours & shade, inskirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600 x 600 mm.

Kota stone slab flooring over 20 mm (average ) thick base laid overand jointed with grey cement slurry mixed with pigment to match theshade of the slab including rubbing and polishing complete . Base with1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand)

Kota stone slabs 20 mm thick in risers of steps skirting. Dado & pillarslaid on 12 mm (average (thick cement mortar 1:3 (1 cement: 3 coarsesand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. Details of cost for 10 sqm

Chequerred precast cement concrete tiles 22 mm thick with marbiechips of size 6 mm in footpath & coutyard jointed with neat cementslurry mixed with pigment to match the shade of tiles including rubbingand cleaning tec. Complete on 20 mm thick bed of cement mortar1:4(1 cement:4 coarse sand

Dark shade using ordinary cement

Providing and fixing pressed steel door confirming IS code 4351manufactured from commerical mild steel sheet of 1.25 mm thicknessincluding hinges, jamb, lock jamb, bead and if required angle threshold ofmild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mildsteel welded or rigidly fixed together by mechnical means, adjustable lugswith split end tail to each jamb including steel butt hinges 2.5 mm thick withmortar guards, lock strike-plate and shock absorbers as specified andapplying a coat of approved steel primer after pre-treatment of the surfaceas directed by Engineer-in-charge:

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete

Fixed to steel windows by welding

Fixed to openings/ wooden frames with rawl plugs screws etc

Providing and fixing steel glazed doors, windows and ventilatrs of standardrolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with woodenplugs and screws or raw) plugs and screws or with fixing dips or with bolts and nuts as required, including providing and fixing of glass panes with glazing dips and special metal-sash putty pf approved make complete including applying a priming coat of approved steel primer; excluding the cost of metal beading and other fitting except necessary hinges or pivots as required.DOOR

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering withvertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grainsor cross bands and face veneers on both faces of shutters 35 mm thick including stainless steel butt hinges with necessary screws

Providing and fixing in position collapsible steel shutters with vertical channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia steel pulleys complete with bots.nuts locking arrangement stoppers handies including applying a priming coat of approved steel prime

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ), transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts,nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Cement plaster in course sand 12 mm cement plaster of mix 1:3 (1 cement:3 coarse sand) Neat cement punning

Cement plaster in course sand 12 mm cement plaster of mix:1:6(1 cement: 6 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix.1:6 (1 cement: 6 coarse sand)

12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of neat cement

12 mm cement plaster 1:4( 1 cement: 4coarse sand) finished with a floating coat of near cement Details of cost for 10 sqm

6 mm cement plaster to ceiling of mix :1:4(1 cement: 4 coarse sand)

Add for plaster drip course/groove in plastered surface or moulding to R.C.C. projections

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washa ble distemper of approved brand and manufacture to give an even shade Applying one coat of cement primer of approved brand and manufacture on wall surface Distemper primer

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade Applying one coat of cement primer of approved brand and manufacture on wall surface:Cement primer

Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade New steel work (two or more coats)

Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade:New wood work (two or more coats)

Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water -proofing compound cleaning the surface before treatment

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .With float glass panes of 5.50 mm thickness(weight not less than 12.50 kg/sqm)

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required

Providing and fixing stainless steel ( Grade 304) railing made of Hollowtubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Coupler110mm

Single tee with door110x110x110mm

Single tee without door110x110x110 mm

110 mm bend

Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge

15mm dia

25mm dia

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT grating of approved quality and colour

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths,as per direction of Engineer -in-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

a) Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump)

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with twoor more coats of synthetic enamel paint of requiredshade complete as required :

80 mm dia

100 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) withblank Gunmetal/Stainless Steel cap and chain as required :

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat,ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted betweenflange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubbergasket, GI bolts, nuts, washers etc.as required :

Providing, installation, testing and commissioning of stainless steel Ystrainer fabricated out of 1.6 mm thick stainless steel, Grade 304,sheet with 3 mm dia holes with stainless steel flange.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mmdia male and female couplings duly bound with GI wire, rivets etc.conforming to IS 636 (type-A) as required :

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following asrequired. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S.Pipe and socket

Providing and fixing carbon-di-oxide fire extinguishers

Providing and fixing ABC powder type fire extinguishers with capacity 6 kg(IS:15683)

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS:904 as required :

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing and Supply Executive table with side unit -Table Top size (1800Lx900Dx760H)mm with 50mm table top thick & side runner size (1200Lx400Dx760H) with 35 mm thk. Straight Line table with two wire manager ,mobile pedestal with 3 drawer /center lock ,interchangeble side runner with 3 drawer with lock, one open shelf ,one closed shutter with lock ,key board trey & CPU Trolly . all complete job.The product should be BIFMA ,Green Guard ,AGSI Certified,ISO 14001, ISO 50001:2011 Certified.

Providing and Supply Executive High Back chair with revolving size (seat -510x480,Back -660x510,Height -min. 470mm max. 540mm) chrome plated base with gas height adustment and central tilting with single locking machenaism. Armrest with padding . all complete job.The product should be BIFMA ,Green Guard ,AGSI Certified,ISO 14001, ISO 50001:2011 Certified.

Providing and Supply Reception table with side unit -Table Top size (1500Lx750Dx750H)mm with 25mm table top thick & side runner size (900Lx400Dx750H) with 25 mm thk. Straight Line table with two wire manager ,mobile pedestal with 3 drawer /center lock ,interchangeble side runner with 3 drawer with lock, one open shelf ,one closed shutter with lock ,key board trey & CPU Trolly . all complete job.The product should be BIFMA ,Green Guard ,AGSI Certified,ISO 14001, ISO 50001:2011 Certified.

Providing and Supply Computer Table size (900x600x1050)mm the table top thk will be 25mm PLPB board and top supported with 50x50mm C legs with the provisionlock ,key board trey & CPU Trolly . all complete job.The product should be BIFMA ,Green Guard ,AGSI Certified,ISO 14001, ISO 50001:2011 Certified. all complete job.

Providing and Supply Office chair(C 2) Back chair with revolving size (seat -450x460,Back -530x460,Height -min. 420mm max. 520mm) nylon base with gas height adustment and central tilting with single locking machenaism. with Armrest . all complete job.The product should be BIFMA ,Green Guard ,AGSI Certified,ISO 14001, ISO 50001:2011 Certified.size (all complete job.

Providing and Supply visiting chair (C-3) for waiting room 3 seater visitor chair Length 1775 mm Xd 690mmxH755mm metal perforated sofa option1) seat &back sigal section2) seat is 410mm from ground Perforated stainless steel seat thickness 1.15 mm seat width 52 Beam mild steel with balck power coating thic kness 1.66 mm staineless stel border for every seat & back stainless stell Handles & die pressed legs at the end of chairs gross weight 30 Kgs the steel is of grade 2502

Sloted angle rack (L) 900m x (D) 450 mm x (H) 2 MTS Slotted Angle racks with 7 panels angle: 40 x40 x 2mm Panels:-20 Gauge the product should b e certified company BIFMA ISO 5000, Green Guard/ Green PRO Sedex, AIOTA, IGBC, AGSI, FSC & PEFC

Steel Almirah with 4 Shelves (L) 900mm x (D) 450mm x (H) 1980 mm Storewell with 4 shelves gauge Body 22 Gauge doors 20 Gauge the Product should be Certified Company BIFMA ISO-50001 Green Guard/Green Pro, Sedex, Aiota igbc agsi, fsc &pefc.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch , modular plate, suitable size G.I. box etc as required.

points

points

Supplying and fixing suitable size G.I. Box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 amps. modular socket outlet and 5/6 amps. modular switch, connections etc. As required

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch,connection etc.As required.

Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/submain wiring along with earth wire with the following size of FRLS PVC insulated copper conducter SC cable in surface / recessed medium class PVC conduit as required.

metre

metre

metre

metre

metre

Meter

Supplying and fixing stepped type electronic fan regulator on the existing modular plate/switch box including connections but excluding modular plate etc. As required.

Supplying and fixing 2 pin, 5/6 amps ceiling rose on the existing junction box / wooden block including connection etc as required.

Supplying and fixing batten/angle holder including connection etc as required.

S/F electronic musical call bell suitable for single phase 230 volts complete bell as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 amps modular socket outlet and 2 nos. 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 4 nos. 5 pin 5/6 amps modular socket outlet and 4 nos. 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 amps modular socket outlet and 25 amp modular SP MCB 'C' curve, including connections, painting etc. as required.

Supplying and fixing following way, horizontal type three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc. as required .(but without MCB/RCCB/Isolator)

S/F following rating, 240/415 volts, 'C' curve circuit breaket suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commossioning etc. as reqd.

Supplying and fixing 4'X18 watt LED batten with minimum efficacy 100 lm/w in aluminium housing and complete with integrated electronic driver etc directly on wall/ ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required.

Supplying and fixing surface mounted following types LED downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying & fixing of following types lamp in the existing electrical fitting/fixtures etc. As reqd.

Brush Less Direct Current (BLDC) Fan without Remote.Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories,including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required

Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required.

Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, IP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

metre

Supplying and fixing following ways, surface/recess mounting, Vertical three phase distribution board ( VTPN DB's ) of CRCA sheet steel, dust protected, duly powder painted suitable for upto 160 amp, four pole MCCB as Incomer and SP/TP MCB's as outgoing inclusive of tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's etc as required. (but without MCCB & MCBs)

Supplying and fixing following rating, 240/415 volts, ‘C’ curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Providing and fixing following rating and breaking capacity and pole MCCB with thrmomagnetic release and terminal spreaders in existing panel board including drilling holes in cubicle panel, making connections etc. as required.

P/F following capacity rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubical panel board including drilling holes in cubical panel, making connections etc. as required.

Providing and fixing following capacity four pole ON-load/ panel mounted changeover switches inside the existing cubical panel board including drilling holes in cubicle panel, making connections etc. as required.

Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supply and fixing of fabricated Electrical control panel of cubical construction, floor/wall mounted type, fabricated out of 16 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator and complete in all respect etc and panel manufactures must be approved by CPRI. (But without RYB inicator, ammeter, voltmeter, inter- connection copper conductor cable/solid copper strip, switchgears etc.

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

Supplying of copper strip of all sizes for busbar strip/ interconnection including drilling holes etc as reqd.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required.

metre

metre

metre

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

metre

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as reqd.

metre

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing & fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required.

Providing and fixing lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Jointing copper/ G.I. tape ( with another copper/ G I tape, base of the finial or any other metallic object ) by riverting/ nut bolting sweating and soldering etc. as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of tinned G.I. bolts, nuts, chuk nuts and spring washers etc. complete as required.

Earthing with G.I. earth pipe 4.5 mtr long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. With charcoal and salt as required.

Supplying and fixing following size/ modules, GI box along with modular base and cover plate for modular switches in recess etc as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and drawing following pair 0.5 sq. mm FR PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/ recessed PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

metre

metre

SITC of 2MP IR Outdoor PTZ Camera - 1/2.8" Progressive Scam CMOS, 1920 X 1080 at 60fps, 4.8 mm to 153 mm, 32XOptical, 16X ditital zoom, color: 0.005 Lux at F1.6, B/W: 0.001 Lux at F1.6, ICR, ONVIF, support H.265, MJPEG, 120 db WDR, 3D Digital Noise Reduction, HLC, BLC, Defog, EIS, Tripple individually configurable stream, 24 VAC & Hi PoE, IR range: 150m, Pan: 360° endless, Tilt: From 15° to 90° (auto-flip), Pan Speed - from 0.1°/s to 160's, Preset Speed: 240°/s, Tilt Speed from 0.1°/s to 120°/s, Preset Speed: 200°/s, Presets- 300, Alarm Input-2-ch alarm input, Alarm Output-1-ch alarm Output, Audio-1 channel input & output, Support on-board storage up to 256 GB (SD card not included), IP66, IK10, Face Detection, Region Entrance Detection, Line Crossing Detection, Region Entrance Detection, Region Exiting Detection, UL, CE, FCC certified. (HI-PoE Injector under Si Scope, if PoE is used) (Model no DS-2DE72321W-AE (Camera) + DS-1602ZJ (wall mount Bracket) or DS-1602ZJ-pole (Vertical Pole Mounting Bracket)) (Approved Makes: HIKvision/Honeywell/Bosch)Equivalent

SITC 2 MP IR Bullet Fixed Camera- 1/2.8" Progressive Scan CMOS, 1920 x 1080 at 25fps, 2.8 mm Fixed lens, 0.01 Lux at F1.2, 0 Lux with IR ICR, ONVIF (PROFILE S) , Support H. 265, H 264, MJPEg, DWDR, 3 D Digital Noise Reduction, Three iidividually configurable stream, 12 VDC & PoE, IR range: 40m, IP67, Edge Anlalytics - Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Video tampering UL, CE, FCC certified (Approved Makes: Hikvision/Honeywell/CP Plus)

SITC 2 MP IR Indoor Dome Fixed Camera- 1/2.8" Progressive Scan CMOS, 1920 x 1080 at 25fps, 2.8 mm Fixed lens, 0.01 Lux at F1.2, 0 Lux with IR ICR, ONVIF Support H. 265, H 264, MJPEG, DWDR, 3 D Digital Noise Reduction, Tripple individually configurable stream, 12 VDC & PoE, IR range: 40m, IP67, IK10, Edge Anlalytics - Line crossing detection, Intrusion detection, Motion detection, Video tampering UL, CE, FCC certified (Approved Makes: Hikvision/Honeywell/CP Plus)

SITC of 43 Inches Commercial Display (Approved Makes: LG /Samsung/Panasonic) /Equipment

SITC of 16 ch Network Video Racoraer Communication OS, Up to 12 Megapixels Resolution , Two independent HDMI outputs, one HDMI output of 4K resolution , 1VGA output with output upto 1920 x 1080, Support H.265, MIPEG , Support N+1 hot space system , Support Dual Power - Redundant, Incoming Bandwidth 320 Mbps, 4 SATA Hard Disk, ANR Technology, 4 SATA interface for 4 HDDs and capacity of each HDD upto 4TB, 3 x USB at least 1 x USB with 3.0, Alarm I/O 16/4, RS-485, RS- 232,2 RJ-45 10/100/1000 Mbps self - adaptive Ethernet interface, Multiple network monitoring: Web viewer, CE, FCC, UL cerfiied, (Approved Make:-

SITC of 4TB Surveillance Hard Disk(Approved Makes:

SITC of 08 port Unmanaged Giga Network PoE Switch : 08 port PoE Switch with PoE standard of IEEE 802.3af, IEEE 802.3at , PoE port, Uplink ports (Approved Makes:

SITC of Network Rack 12U with Standard accessries (Approved Makes:

Supply, Installation, Testing and Commissioning of CAT 6 UTP cable 23 AWG solid copper conductor for Connectivity of Hub room to End Point. (Approved Makes:

Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mana/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/Gl structure of suitable strength with following components complete as required:a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years.b) Power Conditioning Unit (PCU) of 350- 800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency.c) Data Monitoring System complete with accessories.d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required.e) Lightning and surge voltage protection.f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required.

Supplying, installation, testing & commissioning of heat detector operating at 54°C/57°C with rate of rise cum fixed tempreature (dual thermistor) type with mounting base complete with all connection etc. as required.

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.

Supplying, installation, testing & commissioning of manual call Each boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning response indicator Each on surface/recess MS box having two LEDs metallic cover complete with all connections etc, as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line. matching transformer etc. complete as required

station in surface/recess suitable for operation on simplex mode. complete with P.T.T. knob & speaker/microphone enclosed in a M.S.(16 SWG)/ ABS box with break glass in front etc. complete as required.

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required.

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable. Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required.

Supplying, Installation,TestingandCommissioningofAirCooledHiWall split typeAirConditionerscompletewithIndoorunit (IDU), Outdoorunit (ODU), surface / concealed copper Refrigerant piping with insulation (Closedcellelastomericnitrilerubber tubularpipesection)upto3mtr(IDU toODU), copperpowercableupto3.5mtr. (IDUtoODU) , copperpower cableupto3.5mtr. (IDUtoODU) i/cdrainpipeR-32/R-410/R-407Green Refrigerant,wirelessRemoter control, suitable forworkingbetween180 260Vwithlow&highvoltagecutoffand50hz,1phaseACsupplycapable ofperformingcooling,dehumidification,airciculationoffollowingcapacity withScroll/rotarycompressor.Thesystemshall beable todeliver100%of theratedcapacityupto42C.Min5yearOriginal EquipmentManufacturer (OEM)warrantybothcompressor andPrintedCircuitBoard(PCB).Must comply:ElectricalcableISI694or IS9968temperaturesensingcontrol IS /International Electrotechnical Commission (IEC) 60730, hermetic compressorIS10617,heatexchangerIS11329,capacitorIS2993andmotor IS12615.CompleteasperCPWDspecificationandIS:1391Part II2023. The system shall be able to operate up to 50 C (out door ambient temperature)

Supply installation testing and commissioning of Atomatic Voltage Stabilizer of Capacity 5 KVA, input voltage -130V± 10% Each and output-220 V ± 10% of Capacity & input Range 130V to 280 V Model (For 1.5 TON )

supply and fixing of 20/24" ready made M.S. prepainted wall stand structure suitable for 1.5/2.0 -TR split AC Machine including all accessories.

Refrigerant:- Supply and Additional refrigerant Charge of refrigerant R410/410A & equivalent Eco friendly green gas to compensate the additional piping done at site for all systems including testing commissioning as required

Drain piping :-· Providing and fixing of CPVC, 6Kg/cm2 drain water piping with fittings, support and insulated with 6 mm thick closed cell elastomeric nitrile rubber insulation complete as per specification.

metre

Supply and fixing of size l00mmXl00mmXl00mm PVC Tray with cover for covering of insulated copper pipes of AC.

Supplying, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for Suction and Liquid lines, all accessories as per specifications etc. as required

meter

meter

Control cable:-Supply and laying ,testing & commissing of following sizes of copper conductor control cables on existing trau including fixing clamps & proper connections to equipment etc. complete as required

meter

Supply and erection of 4 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 X 220 X 12 mm , small door opening for junction box mounting including 6A 'C' series SP MCB, connector, and suitable size foundation bolts with template as required.(but without pole foundation)

Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, IP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

Providing and making of following sizes octagonal street light pole foundation in reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size ) of specified size including PVC conduit, form work, curing, reinforcement, excavation and refilling etc. as required.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required.

metre

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

metre

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

metre

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Providing , laying and fixing of following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep) and re-filling etc as required.

metre

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 40/63 amps 240 volts, "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal/ coke and salt ) as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface/ recessed PVC conduit as required.

Meter

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying, Installation, Testing and commissioning of CAT6 Copper Information Outlet (IO) with face plate of color as per site requirement, should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D. All copper Cable and Components should be from same OEM to maintain compatibility and interoperability etc. complete as required.

Supplying, Installation, Testing and commissioning of RJ45 Connector for CAT 6/6A Cables. RJ45 modular plug supports 4 twisted pairs, 8 positions, 8 connectors. Housing: PC, UL94V-2, transparent color, Use for 24- 26 AWG stranded wires etc. complete as required.

Supplying, Installation, Testing and commissioning of following CAT6 Patch Cord should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D etc. complete as required.

Supplying Installation Testing and Commissioning of 24 port Cat6 Patch Panel loaded. Must be of 1U height with clear label holders and white label with the panel.

Supplying, installation, Testing and commissioning of following capacity 8 port Layer 2 indoor Network Switch having features and specifications etc. as mentioned here under: Minimum 8 X RJ-45 Gigabit Ethernet Ports and additional 2 X 1G SFP Ports with non-blocking architecture by having Switching capacity of minimum 20Gbps and packet forwarding rate of 14Mpps or higher, 8K MAC table. Internal dual AC Power supply with operating temperature of -5 0C to +50 0C. Jumbo frame: 10KB or higher, IGMP Snooping, IGMP snooping querier and support for IGMP Snooping Fast Leave, Should create 250 or more MLD groups, MLD Snooping, Per VLAN MLD Snooping C MLD Snooping Fast Leave, STP, RSTP, MSTP, Loopback detection, Multicast filtering, VLAN Tagging, ǪOS: 8 Ǫue per port, WRR, IPv4/IPv6 Interface : minimum 100 IPv4 static route entries and minimum 50 IPv6 static route entries, 700 Acess Control entries, SSH CSSL for IPv4 and IPv6, 802.1x, ARP Spoofing, DHCP Snooping and server screening, IP+MAC+Port Binding, Per Port Bandwidth Control, 802.1X Authentication (Supports local/RADIUS database, Port-based Access Control and EAP, OTP, TLS, TTLS, PEAP Support) Cable Diagnostic feature, LLDP, LLDP-MED, SNTP/NTP, RMON, SNMP v1,v2c, v3 and SNMP Traps. Certifications: UL, CE, FCC, RoHS, MTCTE, OEM/Product must be on Trusted Telecom Portal of Department of Telecommunication, Government of India etc. complete as required.

Supplying and fixing of following size Wall Mount Rack having Fixed Structure with 0.8mm CRCA Sheet, completely knocked-down condition (CKD) Shape, Vertical Mounting Rail 1.6 mm with 'U'Marking, Minimum 2 cable entry/exit provision at Top and bottom with rubber protection, Front 5mm Toughened Glass with lock, wall mounting kit, Powder coated Color- RAL- 7035, complied with UL & RoHS, 2 x 6 sockets 16A power distribution units, 3 numbers closed cable organizer, Hardware mounting screws packet of 20 x 1 number, etc. complete as required.