Improvement of water distribution system in GP Kataula Kamand and aug of WSS Riyagri Lanjhnoo in Tehsil Sadar in Distt Mandi HP

Amount

Excavation in foundation and trenches etc. in earth work in all kind of soil such as pick work jumper work,saturated soil including bailing or pumping out water, blasting soft/hard rock, chiseling soft/hard rock where blasting is prohibited in all lifts including trimming and dressing of sides, levelling of bed, stacking the excavated soil clear from the edge of excavation and then returning the excavated soil in 15cm. layers including consolidating each deposited layer by ramming , watering and then disposing of all surplus excavated soil as directed in all leads/lifts and shoring strutting,timbering and dewatering where ever required as per direction of the Engineer-in-Charge.

Providing and laying cement concrete 1 : 2: 4 (1Cement : 2 Sand : 4 graded stone aggregate 20mm nominal size)and curing complete excluding cost of form work and re-inforcement for reinforced concrete work in

Foundation , footing basis of columns & the like and mass concrete complete in all respect and as per the direction of Enginer-in-Charge

Suspended floor ,roofs, lendings and shalves and thier suports balconies, beem griders and bressumers and cantiliver upto floor two level with in all leads and lifts.

Providing and laying cement concrete 1:4:8 (1cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of from work in foundation and plinth with in all leads and lifts.

Providing and laying cement concrete 1:1.5:3 (1cement:1.5 sand : 3graded stone aggregate 20mm nominal size)and curing complete excluding cost of form work and re-inforcement for reinforced concrete work in:-

Foundation , footing basis of columns & the like and mass concrete complete in all respect and as per the direction of Enginer-in-Charge

Wall (any thickness but not less than 0.1 m thickness) attached pillasters, buttresses, plinth and string courses, etc. from top of foundation level upto floor two level complete with in all leads and lifts as per direction of the Engineer-in-Charge.

Suspended floor ,roofs, lendings and shalves and thier suports balconies, beem griders and bressumers and cantiliver upto floor two level with in all leads and lifts.

Providing and laying cement concrete 1:6:12 (1cement:6 sand:12 graded stone aggregate 40mm nominal size) and curing complete excluding cost of from work in foundation and plinth complete in all respect with in all leads and lift and as per the entire satisfaction of Engineer-in Charge.

Random rubble masnory/ polygonal rubble masonry(uncoursed/brought to courses) with hard stone of apporved quailty in foundation &plinth including levelling up with cement concrete 1:6:12(1Cement :6 sand :12greded stone aggregate) in cement mortor 1:6 complete in all respect and as per the direction of Enginer-in-Charge

Brick work using common burunt clay building bricks in supper structure in cement mortor 1:4 ( 1 cement : 4 sand )complete in all respect and as per the direction of Engineer-in-charge.

Providing and fixing pressed steel doors frames manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges, jump lock jamb, beed and if required angle threshold of mild steel angle of section 50X25 mm or base ties of 1.25 mm pressed mild steel welded or regidly fixed together by mechanical means, adjustable lugs with split and tails to each jamb including steel but things 2.5 mm thick with gaurds, lock strike plate and shock as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge.

Providing and fixing panneled glazed or panneled and glazed shutters for doors, windows and clerestory windows, including black enamelled iron butt hinges with necessary screws 40 mm thick 2nd class deodar wood complete in all respect and as per the direction of Engineer-in-Charge

Providing form work with steel plates3.15mm thick welded with Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fairfinish I/c centring , shuttering , strutting and proping etc.with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4m and removal of the same for insitu- reinforced concrete & plain concrete work in :-

Slopping of battering surfaces including folded plates where inclination to horizontal plane dose not exceed 30*

Vartical surface such as walls (any thickness) portion and the like including attached pillers,buteress plinth and staircases and the like.

In foundation, footings & Buttresses etc. in all leads and lifts

Edges of slabs & breaks in floor & walls under 20 cm wide with in all leads and lifts

Flat surfaces such as soffits of suspended fioors roofs landing and the like . Floors etc up to 200mm in thickness.

Beams ,cantilevers, girders and lintels up to floor to level with in all leads and lift.

Providing form work of ordinary timber planking's so as to give a fire finish including centring, shuttering, propping etc. hight of propping and centring blow supporting floor to ceiling and remobal of the same for instu reinforced concrete and concrete work in arches exceeding 6 mtr. span (dome) as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and Fixing of precast concrete man hole cover, 500 mm dia with frame conforming to IS 12593-part-1, 1988 and IS 12592,Part-II 500 mm diameter, medium duty with in all leads and lifts.

Providing tor steel reinforcement for reinforced cement concrete work including bending, binding in position complete upto floor two level complete in all respect and as per the direction of Engineer-in-Charge

Half brick masonry in common brunt clay building bricks in cement mortor 1:4 ( 1 cement:4 sand )With in all lead and lifts and entire satisfaction of Engineer-in Charge.

6mm cement plaster to ceiling in cement mortar 1:3 (1cement:3sand) complete in all respect and as per the direction of Engineer-in-charge.

15 mm cement plaster in single coat on rough side of brick / concrete / stone walls for interior plastering upto floor two level including arrises internal rounded angles, chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortor 1 : 3 (1 Cement : 3 Sand) with in all leads and lifts.

Providing & fixing M.S. grils of required pattern in wooden frame of window etc. with M.S. flats square or round barswith round headedbolts and nuts by screws plan grils complete in all respect and as per the direction of Engineer-in-charge

Boulder filling under floor complete in all respect and as per the direction of Enginer-in-Charge

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 cement :3sand: 6 graded stone aggregate 20mm nominal size) including finishing the top surface of concrete smooth complete in all respect and as per direction of Engineer-in-Charge.

White washing with lime on un-decorated wall surfaces (with two coats) to give an even shade including thoroughty brooming the surface to remove all dirt,dust,mortor dirt and other foreign mattercomplete in all respect and as per direction of Engineer-in-charge

Distempering with oil bond distemper of approved brand and manufacture (two coats) and of required shade on undecorated wall surfaces to give an even shade sand papered smooth.

Providing and fixing oxidized M.S. sliding door bolts with nuts and screws etc. complete 300x16 mm

Providing and fixing anodised M.S. Tower bolts (Barrel type) with necessary screws etc.complete in all respect and as per direction of Engineer-in-charge..

Providing and fixing Oxidized M S Handlewith necessary srews etc complete in all respect and as per direction of Engineer-in-Charge.

Applying priming coat on new steel and steel based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt,and other foreign matter , sand papering and knotting ready mixed paint brushing wood primer pink complete in all respect and as per direction of Engineer-in-charge.

Painting two coats ( excluding priming coat ) on new wood and wood based surfaces with enamel paint to give even shade including cleaning the surface of dust and other foreign matter, sand preparing and stopping with enamel paint other than white complete in all respect and as per direction of Engineer-in-charge.

Precast terrazzo tiles hydraulic compressed 20 mm thick with marble chips of specified size in flooring cement mortar 1:6 (1cement : 6 sand) jointed with neat cement slurry (Dark shade)

Providing and fixing cast iron rungs 200 mm wide with chequered of ribbed non slip surface including fixing in manhole with 200x200x100 mm cement concrete 1:3:6 ( 1 : cement 3: sand 6: graded stone aggregate 20 mm nominal size) complete in all respect in all leads and lifts.

Providing and fixing cast iron spun soil, waste and ventilating pipe lead caulked joints to be measured and paid for separately 100 mm nominal dia. With CI cowl 100 mm dia nominal size with in all leads and lifts.

Laying, jointing, testing in trenches and carriage of GMS tubes (light grade) including tube fittings (earth work to be measured and paid for separately) complete in all respect in all lead and lifts.

a) 80 mm dia

b) 65 mm dia

c) 40 mm dia

d) 32 mm dia

Providing and Fixing Cast Iron Sluice Valve of BIR make BIS No. 14846 with Table-5 including welding of flanges, Nuts & Bolts and Gasket etc. The sluice valve conforming to IS-780. The dia of valve as mentioned below complete in all leads and lifts and to the entire satisfaction of the Engineer-in-Charge in all leads and lifts.

80 mm diameter

Providing and placing in horizontal layers filtering media duly graded, screened, cleaned and washed as specified.

Top layer, Find sand (Eff.Size 0.20mm to 0.40 and uniformity co-effcient 2.00 to 3.00

Second layer, Coarse sand, 3 mm to 6mm

Third layer: Bajri 6mm to 20mm

Fourth layer : Bajri 20mm to 25mm

5th layer : Broken stone 50mm to 75mm

Providing and placing Ist class standared bricks in filter bed in two layers so as to make cross drains complete with in all leads and lifts as per direction of Engineer-in-Charge.

1.20 meter height fencing (as per approved design) 1.80 meters RCC posts 3 metres centre to centre and RCC struts with 9 horizontal lines and two diagonals of galvanised steel barbed wire (IS 278-1962 type I) weighting 9.38 kg/100 metres (minimum) strained and fixed to posts by typing to 6mm galvanised steel bar niles/clips with GI binding wire including cost of Excavation, RCC Posts, RCC struts and straining belts and embedded in cement concrete 1:4:8 (1 cement :4 sand : 8 graded stone aggregate 40 mm nominal size) and curing complete in all respect and to the entire satisfaction of the Engineer-in-Charge in all leads and lifts.

Flush pointing on brick work with cement mortor 1:3 (1cement :3sand) complete in all respect with in all leads and lift and as per the direction of Engineer-in-Charge.

40 mm thick cement concrete flooring 1 : 2 : 4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) laid in one layer with a floating coat of neat cement and curing complete in all leads and lifts.

White glazed tiles 6 mm thick in flooring cement mortar 1 : 3 (1 Cement : 3 Sand) finished with flush pointing in white cement all leads and lifts and to the entire satisfaction of the Engineer-in-Charge.

White glazed tiles 6 mm thick in skirting risers of steps and dado 12 mm thick cement mortar 1 : 3 (1 Cement : 3 Sand) and jointed with cement slurry with in all leads and lifts and to the entire satisfaction of the Engineer-in-Charge.

Providing wood work in frames of door and windows and clerestory windows complete in all respect 2nd class DD Wood.

Providing and fixing panneled glazed or panneled and glazed shutters for doors, windows and clerestory windows, including black enamelled iron butt hinges with necessary screws 40 mm thick 2nd class deodar wood complete in all respect and as per the direction of Engineer-in-Charge

Steel work in single sections including cutting, hoisting, fixing in position and applying a priming coat of red lead paint in R.S. joints, channels angles, tees and M.S. sheet etc. complete in all respect with in all leads and lifts and to the entire satisfaction of Engineer-in-Charge.

Providing and Fixing alluminium sliding door bolts 300x16 mm with in all leads and lifts.

Providing and Fixing MS Handles 125 mm with in all leads and lifts.

Providing and Fixing MS Hinges 125 mm (MR) with in all leads and lifts.

Providing holes for grounting the man hole frame with in all leads and lifts.

Providing and fixing anodised aluminim Tower bolts (Barrel type) with necessary screws etc.complete in all respect and as per direction of Engineer-in-charge. (i) 250x10 mm

Providing and fixing automatic flushing cistern with a pair of C.I. or M.S. brackets complete with fittings including C.I. syphonic apparatus mosquito proof lid, C.P. brass unions and coupling for connections with inlet, outlet and overflow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately) vitreous China 5 litres capacity with in all leads and lifts and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing vitreous China wash down, water closet (European type, W.C. pan) with integral "P" or "S" trap including jointing the trap with soil pipe in cement mortar 1 : 1 (1 Cement : 1 Sand) (Seat and cover to be measured and paid for separately) white colour with in all leads and lifts and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 100 mm size P or S trap for water closet (Squatting Pan) including jointing the trap with the pan and soil pipe in cement mortar 1 : 1 (1 Cement : 1 Sand) sand cast iron with in all leads and lifts.

Providing and fixing viterous china wash basin with single hole for pillar tap with CI or MS bracket painted white including cutting hole including good the same excluding fitting Cera sanitary work (cornet) white 550x400 white with in all leads and lifts.

Providing and fixing viterous china padestral for wash basin complete recessed at the basic for reception of pipe and fittings Cera sanitary work (carnet) white (viterous China in white colour) with in all leads and lifts

Providing and fixing of water storage tank sintex having of capacity 500 litres with necessary fittings including over flow pipes, scour pipes etc. inlet and outlet and inside paint of required size for inlet or outlet and inside paint of approved quality complete including hoisting complete in all respect with in all leads and lifts.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 Kg/Sqcm including fitting the joints with approved adhesive complete with in all leads, lifts and carriage of materials 110 mm nominal bore within all leads and lifts.

Providing and fixing on wall faces PVC door bend (D-Plast) with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive complete 75 mm nominal bore within all leads and lifts.

Providing and Fixing to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fittings and clamp including making good the wall ceiling and floor in all leads and lifts 15 mm nominal bore.

Providing and fixing Gun Metal full way wheel valve 15 mm dia with in all leads and lifts.

Providing and fixing brass bib tap (Superior quality or heavy type) 15 mm dia with in all leads and lifts.

Providing and fixing CP brass soap dish with CP brackets fixed to wooden plugs with CP brass screws complete in all respect in all leads and lifts.

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required.

Group C.

Wiring for circuit / sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping along with 1 No.HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2 x 1.50 Sq. mm.

2 x 4.00 Sq. mm.

a) Supplying and fixing 3 pin 5/6 amps. Socket outlet on the exists switch box/covers including connections etc. as required.

Supplying and fixing 2 way 5/6 amps. Tumbler/piano type switch on the existing switch box on the switch box/cover including connections etc. as required.

a) Supplying and fixing 3 pin 15/16 amps. Socket outlet on the exists switch box/covers including connections etc. as required.

Supplying and fixing 15/16 amps. Tumbler/piano type switch on the existing switch box on the switch box/cover including connections etc. as required.

Supplying and fixing wooden box of following size (nominal) on surface or recess with suitable size of phenolic laminated sheet cover of in front as required.

229 mm.x 102 mm.x 60 mm. deep

203 mm.x152 mm.x 60 mm. deep

Providing and fixing of CFL 1x23 watt of reputed make in all leads and lifts.

Providing and fixing of CFL 1x5 watt of reputed make in all leads and lifts.

Supplying and fixing ceiling rose on existing junction box/ wooden block including connections etc. as required.

Supplying and fixing plain pandent with 16/20 mm twin twisted, flexible PVC insulated copper cable and backelite pendant holder including connections, etc. as required.

Supplying and Fixing 5 Amps to 32 Amps rating, 240 Volts, L series miniature circuit breaker of following poles in the existing MCBDB complete with connections, testing and commissioning etc. as required Cat - A. (Single Pole)

Supplying and Fixing of following way, single pole and neutral, sheet steel, MCB distribution board, 240 Volts on surface/ recess, complete with tinned copper busbar, netural link, earthbar, dibnbar, detachable gland plates, inter connections, i/c painting, earthing etc. as required busbar 8 way.

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. (63 amp. CAT - A)

Providing, installing, testing and commissioning of ceiling fan and regulator i/c wiring the down rod of standard length (upto 30 Cm with 1.5 Sqmm PVC insulated copper conductor signle core cable etc. as required.Ceiling fan 1400 mm sweep category A

Providing and fixing ultra slim decorative extruded box fixture with domestic electronic ballast, snap-on installers, suitable for 28 watt FTL (T5), complete with all accessories (including one No. T-5 Tube), connections, testing and commissioning etc. as required.

1 x28 watt-FTL (T5) (Category-A)

Providing and Fixing LED flood Light watt mentioned below (OREVA make) complete in all respect and to the entire satisfaction of Engineer-in-Charge in all respect in all leads and lifts. LED 20 watt

Providing and fixing two core service wire 6 Sqmm thick in all leads and lifts.

GANTANTAR THAKUR

AMIT CHOUDHARY