Provn of 04 x Toilet Block for Covid Wards for Covid 19 patients consisting of 02 x WCM 02 x IWC algongwith OHT Separate Soakage Well with Geyser facilities between T22 and T23 Covid Ward V and VI and near Bldg No T 31 Covid 19 Isolation Ward Dhobi

Amount

Surface excavation not exc. 30cm deep and averaging 15cm deep and getting out in soft and loose soil.

Excavation in trenches, n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation, cable trenches, laying pipes, etc., for shafts, wells, cesspit, manholes, pier holes etc., n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft and loose soil, complete all as specified and as directed. (15+27+45+22.5)

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm, in soft and losse soil, complete all as directed. (9+13+24+18)

Spreading and levelling in layers n.exc 25 cm thick and well ramming including watering as required, complete all as specified and as directed.

Removing excavated materials n.exc. 50 m and depositing where directed at a level n.exc 1.5m above the starting point, complete all as directed. (4+14+21+4.5)

M & L for PCC (1:4:8) type D2 40mm graded stone aggregate as in, foundation, filling and mass concrete, complete all as specified and as directed. (2.6+3.42)

M & L RCC M-25 grade concrete using 20mm graded aggregate as in foundation, including rafts, footings, foundation beams, plinth beams, bases of column etc., basement slabs, and mass concrete etc., complete all as specified and as directed.

M & L RCC M-25 grade concrete using 20mm graded aggregate slab supported on walls, beams and column in floors, roofs, landings, balconies, canopies, deck slabs and the like etc., complete all as specified and as directed.

M & L RCC M-25 grade concrete using 20mm graded aggregate, as in beams, cantilevers, bressumers, lintel over span 1.5metre etc., complete all as specified and as directed.

M & L RCC M-25 grade concrete as in columns, pillars, piers, post and struts etc., complete all as specified and as directed.

M & L for brickwork with fly ash bricks, straight or curved on plan exceeding 6m mean radius built in CM (1:6), complete all as specified and as directed.

M & L for brickwork with fly ash bricks, straight or curved on plan exceeding 6m mean radius in half brick thick, built in CM (1:4), complete all as specified and as directed.

M & L for formwork to sides concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits of foundation and plinth beams, and similar work; vertical or to batter, fair finished surface concrete flat, etc., complete all as specified and as directed.

M & L for formwork to soffit of suspended slabs such as roof slabs, floor slabs, landings and similar work; n.exc 200m thick (horizontal or sloping) fair finished surfaces of concrete flat, complete all as specified and as directed.

M & L for formwork to sides and soffit of floor beams or roof beams haunching girders, bressumers, lintel, cantilevers, shelves including supports, overhangs etc., also splays between floors and beams etc., fair finished surfaces of concrete flat, complete all as specified and as directed.

M & L for formwork to edge of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roof n.exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work n.exc 10cm but n.exc 20cm wide, complete all as specified and as directed.

S & F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes supplying & fixing in opening as per specification & drawing complete all as spcefied and directed by Engr-In-Charge .

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS framed shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS framed welded/sealed to stiles & rails with suitable PVC sheet beading & joined together with solvent cement complete all as specified and as directed.

Supply and fix 150mm long aluminium anodised barrel tower bolt of extruded section, complete all as specified and directed.

S & F 100mm butt hinges medium weight medium cold rolled mild steel complete all as specified and directed by Engr-In-Charge .

S & F aluminium handles cast type 150 mm long, complete all as specified and directed by Engr-In-Charge.

S & F framed work such as grill grating etc with end of bars shouldered and/or riveted or forged into spikes framed guard bars barred iron doors, ladders, framed balusters, walk ways, railings, framed works of water tanks and and similar works conforming to Fe-290-0 Gde E-165 including all necessary welding complete all as specified and directed by Engr-In-Charge.

S & F portion framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc., with ends of bars shouldered and/or rivetted, or forged into spikes framed guard bars barred iron doors, ladders, framed balusters, walk ways, railings, framed works of water tanks and and similar works conforming to Fe-290-0 Gde E-165 including all necessary welding complete all as specified and directed by Engr-In-Charge.

S & F mild steel TMT bars 10mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping, hooking ends and binding with mild steel wire (annealed) not less than 0.90 mm dia or securing with clips, complete all as specified and directed. (2600+52.65)

S & F mild steel TMT bars 5mm dia and over, as in stirrups cut to length, bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.90mm dia or securing with clips, complete all as specified.

S & F steel window, ventilators, top hung shutter including hinges, steel peg stay, complete all as specified and as directed.

M & L for providing 75 mm thick PCC 1:4:8 type D-2 (Using 40mm grade stone aggregate), complete all as specified and directed.

M & L for 75 mm thick plain cement concrete (1:3:6) mix, type C-1 using 20mm graded stone aggregate as in plinth protection, finishing the surfaces even and smooth without using extra cement,complete all as specified and directed.

Hardcore of broken stone aggregate of gauge n exc 63mm, deposited, spread and levelled in layers not exc, 15cm thick, watered and rammed to a true surface, complete all as specified and as directed.

M & L glazed ceramic coloured tiles of size 375x250x7mm/450x300x7 mm thick as in dado/skirting etc set and jointed in neat cement slurry and pointed in colour cement to match the tiles including 10 mm thick cement plaster in CM (1:4), complete all as specified and directed.

M & L joint free non skid coloured ceramic tiles 7 to 8 mm thick (sqaure/rectangular) area of each tile exe. 0.06 sqm but n.exe.0.11 sqm, in floors etc., over and including 15mm thick screed bed in cement mortar (1:4) set and jointed in neat cement slurry and pointed in coloured cement to match the existing surfaces, complete all as specified and directed.

Material and labour for rendering 10mm thick in CM(1:6) finishing surface even and smooth without using extra cement, on surfaces of brickwork or concrete surfaces, complete all as specified and as directed.

Material and labour for rendering 15mm thick in CM(1:4) finishing surface even and smooth without using extra cement, on surfaces of brickwork or concrete surfaces, complete all as specified and as directed.

M & L 5 mm thick rendering on or concrete surfaces as in ceiling, or on fair faces of brickwork with cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and directed.

M & L preparation of newly plastered surface of walls and applying three coats of white wash on surface, complete all as specified and directed.

M & L preparation of newly plastered surface of ceiling and applying three coats of white wash on the surface, complete all as specified and directed.

M & L for preparation of newly plastered surface of walls using sand paper and applying two coats of cement base paint, white or tinted over a coat of cement primer, complete all as specified and as directed.

M & L for 3mm thick, pin head type, figured sheet glass ordinary quality and glazing with oil putty n.exc 0.50 Sqm in each pane, complete all as specified and as directed by Engr-In-Charge .

M & L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed by Engr-in-Charge.

S & F for GI tubing medium grade including all types of fittings of ISI marked in new or old position to walls, ceiling, floors etc., suitable for 15 mm bore, complete all as specified and as directed.

S & F for GI tubing medium grade including all types of fittings of ISI marked in new or old position to walls, ceiling, floors etc., suitable for 20 mm bore, complete all as specified and as directed.

S & F for GI tubing medium grade including all types of fittings of ISI marked in new or old position to walls, ceiling, floors etc., suitable for 25 mm bore, complete all as specified and as directed. (40+180)

S & F rotational moulded polyethene water storage tanks, double layered (cylinder vertical with closed top) of capacity 1000 lit. hoisted and fixed in position as in repair, complete all as specified and as directed.

S & F bib tap, 15mm, cast copper alloy CP with crutch butterfly handle, screwed for iron pipe or brass ferrule, complete all as specified and as directed.

S & F 15 mm dia angle stop valve of cast copper alloy, fancy type, chromium plated, long shank & cup(concealed type), screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S & F 15 mm dia stop valve of cast copper alloy, screwed down, high pressure, with crutch, of butterfly handle fancy type, chromium plated, with long shank and cup(concealed), screwed both ends for iron pipe or for unions, complete all as specified and directed.

S & F 15 mm bore fancy type pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'HOT' or 'COLD’ with long screwed shank and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F 20 mm dia stop valve of cast copper alloy, screwed down, high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S & F 25 mm dia stop valve of cast copper alloy, screwed down, high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S & F 20mm dia ball brass valve, high pressure with polyethylene float and flynut complete screwed for iron pipe or brass ferrule, complete all as specified and as directed.

S & F for PVC connection pipe of 15 mm dia with PTMT nuts of length 45cm long to WHB and flushing cistern, etc., complete all as specified and as directed.

S & F, 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge.

S & F, 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge.

S & F, 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls, complete all as specified and as directed by Engineer-in-charge.

S & F, 75mm bore PVC (SWR) bends any radius complete all as specified and as directed by Engineer-in-charge.

S & F, 110mm bore PVC (SWR) bends any radius complete all as specified and as directed by Engineer-in-charge.

S & F PVC (SWR) 110 mm bore junction single, (Single T) equal or unequal, with access door complete all as specified and as directed.

S & F 110mm bore PVC(SWR) vent Cowl complete all as specified and directd.

S & F 75 mm dia outlet PVC(SWR) floor trap plain with CP grating with or without hole, including jointing with solvent cement, complete all as specified and as directed.

S & F vitreous china wash down water closet pan, pedestal pattern Pedestal pan and trap (excluding fixing bolts, flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe, complete all as specified and directed.

S & F vitreous China squatting pan (Orissa pattern), of size 580x440 mm white with integral foot rests (excluding flusing cistern and flush pipe) including provn of lime concrete and backing joints, connection to trap and flushing pipe anti syphonage pipe etc., complete all as specified and as directed.

S & F flushing cistern low level, white, PVC 10 lit capacity syphonic action type, valveless with inlet ball valve, float valve and handle including bracket and 32mm flush pipe of polyethylene, complete all as specified and as directed.

S & F for shower rose chromium plated with or without swivel joints 125 mm dia, complete all as specified and as directed.

S & F in repair vitreous China wash hand basin, white, flat back, size 550X400mm including , chain and plug, and porcelain stopper, cast iron brackets, waste pipe complete including cutting for and pinning in ends of brackets and 32 mm dia waste fitting brass chomium plated for wash hand basin etc; with long screwed shanks and fly nuts, flange end bedded in red lead cement , complete all as specified and directed.Make:- Hindware/Parryware/Cera or of equivalent approved make.

S & F plastic water closet seat, black, closed pattern with flat bottom, cover and mild steel CP or aluminised hinging device, complete all as specified and as directed.

S & F Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook including making connection and fixed in position, complete all as specified and as directed.

M & L 10mm thick screed in cement mortar (1:3) on concrete/brick surfaces with liquid water proofing compound @ 200 ml/50 Kg per bag of cement or as per manufacturer instruction finished even and smooth without using extra cement over roof/sunken slab/wall complete all as specified and as directed. (Note: Water proofing liquid shall be measured and paid separately)

M & L for Water Proofing treatment on "non approachable/non accessible roof" surface (Horizontal and vertical surfaces) in following sequence through manufacturer/authorised applicator of the manufacturer all as specified and directed complete. (i) Applying approved bituminous based primer conforming to IS: 3384-1955 @ 0.3 Kg/Sqm to be applied on top surface of prepared surface till the surface is properly impregnated. (ii) Laying APP (Atactic polypropylene Polymer modified prefabricated membrane) water proofing membrane of weight not less than 3 Kg/Sqm with minimum 100 mm side overlap along the length from downward to upward completely sealed with Torch apllication /hot blown lamps. (iii) Laying unrolled over the bitumen coated surface, polymeric membrane Hyperplas standard weight not less than 3 Kg/Sqm with 100 mm overlaps shall be sealed by flame as per manufacturer's instructions. (iv) Applying two coats of bituminous based aluminium paint @ 0.3 Kg/Sqm, complete all as specified and as directed.

Supply only liquid integral proofing compound, complete all as specified and directed.

S & F CP toilet paper holder fixed to walls complete all as specified and as directed.

S & F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed by Engr-In-Charge .

M & L for brick work with sub class 'B' bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 50 Kg/Sqcm) old size bricks, straight or curved on plan exceeding 6m mean radius built in CM (1:4), complete all as specified and as directed.

Material and labour for rendering 15mm thick in CM(1:4) finishing surface even and fair, on surfaces of brickwork or concrete surfaces, complete all as specified and as directed.

Supply only integral proofing compound, complete all as specified and directed.

M & L for providing precast RCC cover slab for drain, manholes etc., made out of cement concrete 1:2:4 type B1 using 20mm graded aggregate and set in cement mortar 1:4 including all necessary formwork, complete all as specified and directed.

M & L for cement concrete type B2, 1:2:4 (using 20 mm graded aggregate) in coping, moulded or chamfered edged and the like., complete all as specified and directed.

M & L for cement concrete type B1, 1:2:4 (using 20 mm graded aggregate) in surface channel and drains, complete all as specified and directed.

M & L for Reinforced concrete pipes 150mm dia , class NP2, laid in trenches and jointed complete with collars, complete all as specified and directed.

M & L for PCC (1:3:6) type C-2, (using 40mm graded broken stone aggregate) as in bed to drain pipes of the 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested, complete all as specified and directed.

M & L for conventional type septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC (1:4:8) below foundation, RCC M-30 Design mix in cover slabs, roof slab including beams etc. Brickwalls, PCC base slab, baffle walls with vent shaft manhole openings with cover connection etc., complete with effective depth of 1.5m and overall depth of 3 metre for 25 Users, complete all as per drawing No. CEJZ/TD/812/91, Sht 1/2, 2/2 dt of Drg16.04.91 and Rev date 14.07.95.

M & L for soakage well 1.80 m dia and 3.00 m deep, excavation in any type of soil, foundation in PCC (1:3:6) walls of honey combed masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of brick masonry in cement mortar, RCC cover slab in M-25/SFRC cover, interconnecting pipes of RCC/DWC, complete filled with brick bats of size all as shown in drawing No. CEJZ/TD/58/2000, Sht 1/1, dt 05.05.2000.

M & L for point wiring for one light/ fan point/call bell controlled by one switch with 1100 volt grade PVC insulated 1.5 Sq mm multi stranded FRLS copper conductor cable with continuous earth wire of 1.5 Sq mm multi stranded copper conductor cable PVC insulated-unsheathed, drawn in & including concealed rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 20 mm dia & sunken anodized pressed sunken boxes made out of not less than 1.0 mm thick sheet, covered with 2.8 mm thick laminated insulated cover make sheet for housing/fixing switches etc complete all as specified and directed.

All as per item No 83 here-in-before but 1.5 Sq mm for 5 Amp socket outlet, 3 pin, on same board with 1.5 Sq mm earth wire complete.

M & L for point wiring for 15 Amp independent power point controlled by one 15 Amp switch with 1100 volt grade PVC insulated 2.5 Sq mm multi stranded FRLS copper conductor cable with continuous earth wire of 2.5 Sq mm multi stranded copper conductor cable PVC insulated-unsheathed, drawn in & including concealed rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 25 mm dia & sunken anodized pressed sunken boxes made out of not less than 1.6 mm thick sheet, covered with 2.8 mm thick laminated insulated cover make sheet for housing/fixing switches, sockets etc., complete all as specified and directed.

S & F switch piano flush button single pole one way 5 Amp, complete all as specified and as directed.

S & F socket outlet 2 in 1, 3 pin, 5Amp, flush type, universal, complete all as specified.

Supply and fix ceiling rose three terminals PVC/ Polycarbonate, isolated body, ISI marked, complete all as specified.

S & F lamp holder, PVC/Polycarbonate type with back plate having matching colour to holder suitable for angle/batten fittings (ISI marked), complete all as specified.

S & F LED Bulb of capacity 15 Watts lumen output (500) length 102 mm dia 56 mm base cap B22, (ISI marked) complete with all accessories base (ISI marked) all as specified and directed by Engr-in-Charge. Cat Part no. LHLDERHEML8X015 of Havells or its equivalent Of make Bajaj/Phillips/Crompton Greaves, complete all as specified and as directed.

S & F in repair LED light fitting 1 x 20W, 220 V, AC decorative box type with driver, holder including LED tube light 20W connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting, complete all as specified and as directed by Engr-in-Charge. Make: Havells/Bajaj/Crompton Greaves/Phillips.

S & F exhaust fan, steel body AC single phase, 230V of size 300 mm sweep with blades and frame and louvers, complete all as specified and as directed. Make: HAVELLS/BAJAJ/USHA/CROMPTON GREAVES/KHAITAN.

S & F sheet metal enclosures for DBs single pole & neutral 4 way double door with with IP-43 IK-09 protection including 200 Amp rated bus bar and neutral link (ISI marked), complete all as specified and as directed.

S & F amp rating 240V, 10 kA 'C' Curve miniature circuit breaker (MCB) of single poles and neutral and current carrying capacity 32 Amp in the MCB DB complete with connection testing and commissioning all as specified and as directed. Make: IndoAsian or its equivalent make in Havells/Standard/L&T.

S & F amp rating 240V, 10 kA 'B' Curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp in the MCB DB complete with connection testing and commissioning all as specified and as directed. Make: IndoAsian or its equivalent make in Havells/Standard/L&T.

M&L, for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts check nuts & washers of galvanised iron or steel, as shown in electrical plate No.3 of SSR Part-I, connected to earthing testing point all as specified and directed including excavation and connected work in hard/dense soil, PCC 1:3:6 ty C-1 as in pit, 20mm dia GI pipe medium grade for watering pipe, 15mm dia bore GI light grade as earth lead protection pipe, 50mm thick RCC 1:2:4 type B-1 cover slab of size 300x300x50 mm as earth lead protection pipe, 50 mm thick RCC (1:2:4) type B-1 cover slab of size 300x300x50 mm as earth pit cover reinforced with 8mm dia TMT bars @ 10cm C/C both ways and with handle made out of 10 mm dia bars, funnel, strainer, charcoal and testing complete all as specified and directed. Note : (a) Rate quoted deemed to be included of excavation and earthwork in any type of soil with PCC type C-1 in pit PCC cover (b) Earth test result should not less than one ohm.

Supply and fixing electric water heater storage type steel body with copper inner tank and heating element upto 2 KWH capacity 25 litre, BEE 5 Star rated complete with all connected accessories such as safety valve, thermostats, heating element, NRV, connection piece, stop valves, water connection from tank to geyser, etc., complete all as specified and as directed.

S & F PVC connecting pipe 15mm size with PTMT nuts of length 450mm, (ISI marked) connect to water heater, complete all as specified and as directed.

S & F 15 mm dia stop valve of cast copper alloy, screwed down, high pressure, with crutch, fancy type, chromium plated, with long shank and cup(concealed), complete all as specified and directed.

S & F sheet metal enclosures, single pole and neutral (SPN) with two pin and earth socket, complete with one single pole MCB 20 Amps, complete all as specified and as directed.

Supply and lay cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 Sqmm 2 core, complete all as directed by Engineer-in-charge.

M & L for supplying and laying reinforced precast concrete cable cover class LV, type-1 flat size 250 mm x 150mm x 40mm, complete all as specified and as directed by Engr-in-Charge.

M & L for sand cushioning for protection of underground cable, consolidated and compacted with clean dry sand, complete all as specified and as directed by Engr-in-Charge. (Note: The depth of sand shall be measured after compacting the sand).

Supply and laying GI pipe 50mm dia light grade with all necessary fittings for cable protection, complete all as specified and as directed.

Supply and fix gun metal globe or gate valve with iron wheel head screwed at both ends for iron pipe for size 25mm dia, complete all as specified and as directed.

Material and labour for drilling water pipe, taking new tapping from existing pipe, proper welding to the pipe surface, complete al as specified and as directed.

M/s Ray construction

M/s Popatlal A Rathod

ganpati enterprises

Paras Nath Singh

upadhyay engineers and consultant

M/S Parmar Construction

ranjit singh