SPECIAL REPAIR TO BLDG NO P-09 (SINGLE OR LIVING) AT NARENDRA NAGAR UNDER GE 871 EWS.

SCHEDULE 'A' PART-I : BOQ OF WORKS FOR B/R WORKS.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specifed and directed.

Dismantling wrought iron or mild steel work of framed truss etc, any description not otherwise provided for, complete all as specified and as directed.

Rolled mild steel in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.confirming to Fe 410-W (Gde- E- 250) quality- A, complete all as specified and as directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10cm width or girth including and applying two coats of synthetic enamel paint over one coat of zinc chrome/ red oxide primer, complete all as specified and as directed.

Preparation of old painted steel surfaces of any description, over 10cm width or girth including and applying one coat of synthetic enamel paint, complete all as specified and as directed.

Dismantling of old/ damaged existing roof treatment with concrete and cleaning all waste and dirt by wire mesh, picking, sweeping and washing down with water to remove dust, etc, and removal of all material out side the cant area, complete all as specified and as directed.

Rendering 10mm thick on fair faces of concrete surfaces, in cement mortar 1:4 on roof top, including duly mixed with water proofing chemical i.e. PIDI Proof-LW/ STP No 01/ FOSROC India/ Berger, in proportion of 200ml per 50 Kg of cement, rendering is to be finished even and smooth (without using extra lime or cement), complete all as specified and as directed. Note: Cost of water proofing chemical shall be paid separately under respective item of BOQ.

Water proof treatment on roof top with APP (Ataxic Poly Propylene) modified polymeric five layered membrane with central core of 100 micron high molecular high density polyethylene film, minimum weight not less than 3.0 Kg/ Sqm, not less than 3.0mm thick, centre core is sandwiched on both sides by high quality polymeric mix with properties of high softening point, high heat resistance and cold resistivity to make it ideal for all water proofing treatment, with polymeric mix protection on both sides with 20 micron HMHDPE film, laid over one coat of bituminous primer conforming to IS: 3384, applied @0.40 Kg/ Sqm and one coat of hot blown bitumen of 85/25 grade, conforming to IS:702, applied @1.20Kg/ Sqm on prepared surfaces of roof, overlap should be not less than 150mm at ends and 75mm at sides, joints and overlaps uniformly bounded with LPG torch flame including applying of one coat of semi hot blown bitumen of 85/25 grade, @1.20 Kg Sqm and fine screened sand in dry condition @0.50 Kg/ Sqm after laying the membrane, complete all as specified and as directed. Note: Water proofing treatment shall be done on prepared plaster surfaces of roof top.

Plain cement concrete M-15(1:2:4), type B-0 (using 12.50mm graded crushed stone aggregate), nominal mix, including duly mixed with water proofing chemical i.e. PIDI Proof-LW/ STP No 01/ FOSROC India/ Berger, in proportion of 200ml per 50 Kg of cement, 25mm thick, as in roof surfaces to maintain proper slope, finished even and smooth without using extra cement, complete all as specified and as directed.

Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm each, complete all as specified and as directed.

Taking down of chowkhats or frame with shutters (without taking off shutters from the frames) area exceeding 1.50 Sqm but not exceeding 4.0 Sqm each, complete all as specified and as directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows and other Frames/ Chowkhat of size 65mmx125mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) fabricated with meter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/ Cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with mild steel hold fast/ lugs/ SS dash fasteners of required dia and length, complete all as specified and as directed. Note: (i) Mild Steel hold fast/ lugs or SS dash fasteners shall be paid for separately. (ii) WPC solid door/ window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Factory made solid panel PVC door shutter 30mm thick, wood plastic composite (WPC) moulded gauged shutter with wire mesh in any number of divisions with brown wood grain texture including stainless steel wire mesh fixed with 15mmx15mm square tube in side rails with screwing 8mmx28mm heat metal zinc coated screws which can be refix again after replacement of stainless wire mesh as per requirement, complete all as specified and as directed.

Butt hinges, size 100mm, medium weight, cold rolled mild steel, and fixed, complete all as specified and as directed.

Aluminium anodised, barrel tower bolts of extruded Section, size 200mm long and fixed, complete all as specified and as directed.

Aluminium alloy, anodised, sliding door bolt, size 300mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed.

Extruded aluminium alloy handles, fabricated type, anodised, size 150mm, complete all as specified and as directed.

Mild steel, 300mm, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and as directed.

Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed. Note: Stainless steel butt hinges and necessary stainless steel screws shall be paid separately.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, having 140mm overall length of cover plate, fixed in floor, complete all as specified and as directed.

Rolled mild steel in Bands, straps, supports or stays for rainwater, ventilating pipes, clamps; hold fasts; wall ties; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three-way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and as directed.

Factory made uPVC white colour Three track three panels sliding door with fly proof S.S. wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116mmx45mm and sash 46mmx82mm both having wall thickness of 2.3mm+ 0.20mm and single glazing bead/ double glazing bead of appropriate dimension (area of door above 2.00 Sqm upto 5.00 Sqm) comprising of uPVC chambered frame, with in-built roller track and sash extruded profiles duly reinforced with 1.60mm+0.20mm thick galvanized mild steel section made from roll forming process of required length (shape and size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required). Stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 Kg), galvanised iron fastener 100x8mm size for fixing frame to finished wall and necessary stainless-steel screws etc. Profile of frame and sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and as directed. Note: (i) For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth and width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (ii) Glass or wire mesh shall be paid separately.

Galvanised mild steel wire cloth. 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and as directed.

Sheet glass, 4.80mm thick, tinted, ordinary quality and glazing with oil putty or by any means, in square exceeding 0.50 Sqm in each pane, in square or any size, complete all as specified and as directed.

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level), ncluding cleaning, removal and disposal of rubbish/ waste materials from premises, complete all as specified and as directed.

Plain cement concrete M-15(1:2:4), type B-0 (using 12.50mm graded crushed stone aggregate), nominal mix, 40mm thick, as in floors, finished even and rough to receive floor finishes, complete all as specified and as directed.

Plain cement concrete M-10.0(1:3:6), type C-1 (using 20mm graded crushed stone aggregate), nominal mix, 75mm thick, as in plinth protection, finished even and rough without using extra cement, to receive floor finishes of any type, complete all as specified and as directed.

Plain cement concrete M-7.50(1:4:8), type D-2 (using 40mm graded crushed stone aggregate), nominal mix, 100mm thick, as in sub base of floors, finished even and rough without using extra cement, to receive floor finishes of any type, complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and applying neat cement slurry with 3.0 Kg of cement per Sqm by brush, complete all as specified and as directed.

Vitrified Ceramic tiles of light shade, 10mm thick (square/ rectangular) polished, non-skid, area of each tiles not exceeding 0.36 Sqm but not exceeding 0.42 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, and including laid over screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and as directed.

Vitrified Ceramic tiles of light shade, 10mm thick (square/ rectangular) polished, non-skid, area of each tiles not exceeding 0.36 Sqm but not exceeding 0.42 Sqm, set and jointed in neat cement slurry and pointed in white or colour cement to match, the shade/ colour of tiles including rendering of 10mm thick in cement mortar 1:4 as backing of tiles, complete all as specified and as directed.

Curtain rod, 25mm dia, stainless steel, fancy type with fixing and inlcuing end knobs, fixing brackets, stops, round rings to hold the curtain, fixing with wall plugs and screws, complete all as specified and as directed.

Dismantaling of brickwork or stone/ boulder masonry, including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles built in cement mortar or cement lime mortar of any description, complete all as specified and as directed.

Brickwork with subclass ‘B’ bricks, straight or curved on plan exceeding 6.0 mtr mean radius built in cement mortar 1:6, complete all as specified and as directed.

Chequered cement concrete coloured tiles, pre-polished, size 300mmx300mmx25mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over 20mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specified and as directed.

Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed bed 15mm thick on cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and as directed.

Rendering 10mm thick on fair faces of on brick work or concrete surfaces, in cement mortar 1:6, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed.

Rendering 10mm thick on fair faces of concrete surfaces, in cement mortar 1:4 on roof top, including duly mixed with water proofing chemical i.e. PIDI Proof-LW/ STP No 01/ FOSROC India/ Berger, in proportion of 200ml per 50 Kg of cement, rendering is to be finished even and smooth (without using extra lime or cement), complete all as specified and as directed. Note: Cost of water proofing chemical shall be paid separately under respective item of BOQ.

Rendering 5mm thick on fair faces of on brick work or concrete surfaces of ceiling, in cement mortar 1:4, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed.

Supply only liquid water proofing compound, complete all as specified and as directed.

Preparing the new plastered surfaces by any means of external walls for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali and fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over new surfaces, over a one coat of exterior water based primer by using roller/ spray machine, complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc, complete all as specified and as directed.

Excavation in post holes (or similar holes) each nor exceeding 0.50 Cum, getting out in any type of soil including returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 Cm, complete all as specified and as directed

Plain cement concrete M-7.50(1:4:8), type D-2 (using 40mm graded crushed stone aggregate), as mass concrete in foundation, complete all as specified and as directed.

SCHEDULE 'A' PART-II : BOQ OF WORKS FOR E/M WORKS.

Excavation in trenches, not exceeding 1.50mtr wide and not exceeding 1.50mtr in depth; for foundation, etc. or for laying cable, pipe lines, not exceeding 10 Sqm on plan and not exceeding 1.50 mtr in depth and getting out, in any type of soil, complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm, any type of soil, complete all as specified and as directed.

Removing excavated soil not exceeding 50mtr and depositing where directed at a level not exceeding 1.50 mtr above the starting point, complete all as specified and as directed.

Sand cushioning to protection of underground cables, laid 8 Cm before laying and 15 Cm after laying of cable, and punned to form an overall layer of 18 Cm thick, complete all as specified and directed. Note: Punned thickness shall be measured.

Sub class ‘B’ bricks, modular size, brick covering laid dry, flat, transversally along the length of cable on sand cushioning for mechanical protection of cable, with width equal to the length of the brick, complete all as specified and directed.

Tubes, 'light grade' galvanised, 40mm bore, ISI marked including all fitting such as bends, socket, connectors, back nuts, etc, laid in trenches or under floors, complete all as specified and as directed.

Replacement of old unserviceable/ damaged cable with new XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 Volts grade, cross-sectional area 16.0 Sqmm, 4.0-core, laid in trenches or passing through pipes, including suitable lugs and accessories for making connections at both ends, complete all as specified and as directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc, complete all as specified and as directed.

Point wiring (in new concealed conduits to surfaces) for one light/ fan/ bell point controlled by one switch with 1.50 Sqmm, PVC insulated, unsheathed, single core, multi-stranded, copper conductor cable, FRLS, 1100 Volts, using colour coding, drawn in and including any type of new conduit, any size/ dia including all accessories concealed by chasing/ cutting or fixed with PVC plug and mild steel screws on the surface of walls/ floors/ ceilings and making good the disturbed surface matching to existing descriptions/ specifications, with and including sunken type pressed steel/ welded mild steel terminal box 1.20mm thick coated with anti corrosive paint with bakelite laminated sheet top cover 3.0mm thick and including FRLS PVC green insulated unsheathed 1.50 Sqmm copper earth continuity wire connected to earth dolly, complete all as specified and as directed.

Description all as serial item No- 2.09 here-in-before but for one 3- pin, 5/ 6-Amps, socket outlet on same board.

Description all as per serial item No- 2.09 here-in-before but for one 3-pin socket outlet 5/6 -Amps on the independent board.

Point wiring (in new concealed conduits to surfaces) for 3-pin, 15/ 16 Amps, switch socket combination on independent board with 4.0 Sqmm, PVC insulated, unsheathed, single core, multi-stranded, copper conductor cable, FRLS, 1100 Volts, using colour coding, drawn in and including any type of new conduit any dia including all accessories concealed by chasing/ cutting or fixed with PVC plug and mild steel screws on the surface of walls/ floors/ ceilings and making good the disturbed surface matching to existing descriptions/ specifications, with and including sunken type pressed steel/ welded mild steel terminal box 1.20mm thick coated with anti corrosive paint with bakelite laminated sheet top cover 3.0mm thick and including FRLS PVC green insulated unsheathed 4.0 Sqmm copper earth continuity wire connected to earth dolly, complete all as specified and as directed.

Lamp holder, PVC Polycarbonate type with back plate suitable for batten fittings, complete all as specified and as directed.

Switch piano, flush type, single pole, one way, 5/ 6 Amps, complete all as specified and as directed.

Switch piano, flush type, single pole, one way, 15/ 16 Amps, complete all as specified and as directed.

Socket outlet, 2-in-1, 3-pin, 5/ 6 and 15/ 16 Amps, combined, flush type, complete all as specified and as directed.

Socket outlet, 2-in-1, 3-pin, 5/ 6-Amps, flush type, complete all as specified and as directed.

Ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body, size 65mmx25mm dia, complete all as specified and as directed.

Stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc, capacity 120 Watt, 2-module, 240 Volts, single phase, complete all as specified and as directed.

Sheet metal enclosures for Single Pole and Neutral distribution boxes with double door glazed for incorporating MCBs, IP-65, 8-way with 200 amps rated busbar, 240 volts, as per IS-8623, fixing in repairs, complete all as specified and as directed.

Sheet metal enclosures for Triple Pole and Neutral distribution boxes with double door glazed for incorporating MCBs, IP-65, 4-way with 200 amps rated busbar, 415 volts, as per IS-8623, fixing in repairs, complete all as specified and as directed.

MCB, single pole, 6 to 32 Amps, 240 Volts, 50 Hz, 'C' curve including necessary incoming and out going electric connection with suitable size of copper lugs, fixing in repairs, complete all as specified and as directed.

MCB, double pole, 32 Amps, 240 volts, 50 Hz, 'C' curve including necessary incoming and outgoing electric connection with suitable size of copper lugs, fixing in repairs, complete all as specified and as directed.

MCB, double pole, 40 Amps, 240 volts, 50 Hz, 'C' curve including necessary incoming and outgoing electric connection with suitable size of copper lugs, fixing in repairs, complete all as specified and as directed.

LED lights fitting wall surface mounted, 20 Watt, 220 Volt, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and as directed. Make: Havells cat part No- LED Pride Plus Triyca Batten 20 W 6500 K or equivalent in Philips/ Bajaj/ Crompton.

LED lamp, capacity 9 Watt, B-22 holder base with ploycarbonate body and aluminium heat sink, warm/ white light, fixing in repairs, complete all as specified and as directed. Make: Havells ordering code- LHLDDDECIC5R009 and cat part No-LED PLUS 9 W B22 CDL 2S LAMP V8i or equivalent in Philips/ Bajaj/ Crompton.

LED street light fitting 35 Watt 230 Volt, AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, connecting up with three core flexible copper conductor cable of suitable size, and including house service bracket for mounting light fittings House service bracket any type complete with 1.50mtr long galvanised iron pipe 40mm dia medium grade, bent to required shape including mild steel clamps of flat iron 40x6mm, hook, stay, nut, bolt and washer including painting with two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed. Make: Havells cat part No- Superb Street Light 30 W 6500 K IP65 or equivalent in Phillips/ Bajaj/ Crompton.

Earthing complete with galvanised iron earth plate electrode 600x600x6mm buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of earth plate not less than 1.5mtr below normal ground level, connected with galvanised iron wire, size 4.0mm dia as earth lead, by means of bolts, nuts, check nuts and washers of galvanized iron or steel complete with 20mm dia GI light grade protection pipe, 20mm dia GI medium grade watering pipe with funnel including charcoal, dust, salt, PCC M-15, type B-1 in pit with precast RCC M-15(1:2:4), type B-1 (using 20mm graded crushed stone aggregates) in cover reinforced with XPM not less than 4.0 Kg per Sqm, test point etc. all as shown in electric plate No-3 of SSR Part-I (2009), complete with necessary earth work in any type of soil, removal to a distance not exceeding 50mtr, including testing on completion, complete all as specified and as directed by Engineer-In-Charge. Note: Earth pit chamber and RCC pit cover shall be painted with two coats of red synthetic enamel paint over one coat of primer including preparing of surfaces.

Amount of Schedule of credit as mentioned here-in-after shall be deducted from quoted amount.

Please Enable Macros to View BoQ information