Lake and garden development near vav at Ambapur in GMC area with 5 years O&M works (Re-invite)

Grand Total (TS Amount)

Total Amount (In

Grand Total (TS Amount) 197815630

BILL OF QUANTITIES

S.NO DESCRIPTION QUANTITY UNITS RATE AMOUNT

A Dismantellig and Eartwork / Base Courses

Clearing and grubbing road land including uprooting rank vegetation grass

bushes,shrubs,sapling and trees girth up to 300 mm removal of stumps of trees cut

1 earlier and disposal of unserviceable materials(A) By manual means in area of light 12.25 Hectare 85698.98

Demolition and disposal of unserviceable materials with all lead and

lift.(i) Unreinforced concrete.

Excavation for foundation upto 1.5 m depth including sorting out and stacking of

3 useful materials and disposing off the excavated stuff upto 50 Meter lead.(B) Dense 2696.454 cums 155.6

Add extra for Disposing off the excavated stuff of above items for lead of (E) 400 to

Filling available excavated earth (excluding rock) in trenches. plinth, sides of

5 foundations etc. in layers not exceeding 20 cm. in depth consolidating each 1350 cums 135.56

disposited layer by ramming and watering

Suppliying of graded stone aggregate of following sizes (for W.B.M. Road)(3)

Crushed stone aggregate for Hard Quality up to 63 mm stze

Spreading the stone aggregate for rolling and W.B.M. including filling the

interstices to required camber and gradient (excluding spreading of Blindage)(ii)

40mm to 63mm size aggreagates (H.B.)

B Concrete works

Providing and laying cement concrete work 1:2:4 (1- Cement : 2- Coarse sand : 4-

graded stone aggregates 20 mm nominal size) and curing complete excluding cost of

formwork and reinforcement for reinforced concrete work in (A) Foundations,

footings, Base or columns and Mass concrete

Providing and laying in position Ready Mixed M-200 grade concrete for reinforced

cement conctere work , using cement content as per approved Design Mix

manufactured in fully automatic batching plant and transported to site of work in

transit mixer for a lead up to 10 kms having continuous agitated mixer,

manufactured as per mix design of specified grade for reinforced cement concrete

9 work including pumping of R.M.C. from transit mixer to site of laying, excluding 518.7 cums 4915.03

the cost of centering shuttering finishing and reinforcement including cost of

admixtures in recommended proportions as per IS: 9103 to accelerate/ retard

setting of concrete, improve workability without impairing strength and durability

as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as

per latest IS 456 shall be maintained)

Providing formwork of ordinary timber planking so as to give a rough finish

including centering shuttering strutting

and propping etc. Height of propping and centering below supporting floor to

ceiling not exceeding 4 M. and removal

of the same for in situ reinforced concrete and plain concrete work in. (A)

Foundations Footings Bases of Columns etc. and Mass concrete.

11 Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, 61076.925 kgs 76.52

binding and placing in position complete upto floor two level

C Flooring and Cladding works

Providing and laying gang saw cut 30 mm thick, mirror polished / shot blasted pre

moulded and pre polished machine cut granite stone of required size and shape of

approved shade, colour and texture in footpath, flooring in road side plazas and

similar locations, laid over 20mm thick base of cement mortar 1:4 (1 cement :

coarse sand) including grouting the joints with white cement mixed with matching

pigment, epoxy touch ups etc. complete as per direction of Engineer-in-Charge.

16.87.1 With granite stone of colour black, cherry/ruby red of area less than

S.NO DESCRIPTION QUANTITY UNITS RATE AMOUNT

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre

height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1

cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white

cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To

be secured to the backing and the sides by means of cramps and pins which shall be

paid for separately) :Stone work (machine cut edges) for wall lining etc. (veneer

13 work) upto 10 metre height, backing filled with a grout of average 12 mm thick 3015 sqm 7278.2

cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement

mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching

the stone shade : (To be secured to the backing

and the sides by means of cramps and pins which shall be paid for

separately) : 8.14.3 White sand stone - exposed face fine dressed with rough backing

. 8.14.3.1 70 mm thick

13.1 Extra labour for Chiselling in approved patterns and texts 4 Day 816

Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel

dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar

1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar

including ruled pointing etc. complete as per direction of engineer-in-charge.

Providing and laying tactile tile (for vision impaired persons as per standards) of

size 300x300x9.8mm having with water absorption less than 0.5% and conforming

to IS:15622 of approved make in all colours and shades in for outdoor floors such as

15 footpath, court yard, multi modals location etc., laid on 20mm thick base of cement 198.0 Sqm 2017.6

mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the

joints with white cement mixed with matching pigments etc. complete as per

direction of Engineer-in-Charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks

in footpath, parks, lawns, drive ways or light traffic parking etc, of required

strength, thickness & size/ shape, made table vibratory method using PU mould,

laid in required colour & pattern over 20mm thick mortar, compacting and proper

embedding/laying of inter locking paver blocks into the sand bedding layer through

vibratory compaction by using plate vibrator, filling the joints with sand and cutting

of paver blocks as per required size and pattern, finishing and sweeping extra sand.

complete all as per direction of Engineer-in-Charge

60mm thick cement concrete paver block of M-35 grade with approved colour,

design & pattern.

Providing and laying Vitrified tiles 8 to 10 mm thick , 36'' x 36'' in flooring , treads

17 of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3- 300.0 Sqms 1516.65

coarse sand ) finishing with flush pointing in white cement.

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick

base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 laid over and

jointed with grey cement slurry including rubbing and polishing etc. complete. (B)

D KERBS & BOLLARDS

Providing and laying at or near ground level factory made kerb stone of M-25 grade

cement concrete in position to the required line, level and curvature, jointed with

cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or

19 without grooves (thickness of joints except at sharp curve shall not to more than 59.4 Cumt 10117.6

5mm), including making drainage opening wherever required complete etc. as per

direction of Engineer-in-charge (length of finished kerb edging shall be measured for

payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Precasting and placing in position Bollards of required shape and size including

providing M.S. Pipe Sleeve 50 mm dia 300 mm long in the Bollard and M.S. Pipes

40 mm dia and 450mm long with 150x150x6mm M.S. plate welded at bottom and

embedded 150mm in cement concrete 1:3:6 (1 Cement : 3 coarse sand (zone-III)

derived from natural sources : 6 graded stone aggregate 20 mm nominal size

derived from natural sources), including necessary excavation of size

250x250x450mm deep for the same in bitumen/concrete pavement at specified

Provding and fixing stainless steel bollard in position 125 mm dia Bollards

mm high of required shape including all the ss fitting etc.

E Masonary / stone Work

Coursed rubble masonry (first sort) with hard stone in foundation and plinth with :

7.6.1 Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of

23 classndesignation 7.5 in superstructure above plinth level up to floor V level in all 635.64 cums 9344.35

shapes and sizes in : 6.4.1 Cement mortar 1:4 (1 cement : 4 coarse sand)

S.NO DESCRIPTION QUANTITY UNITS RATE AMOUNT

Steel work in built up tubular (round, square or rectangular hollow tubes etc.)

trusses etc., including cutting, hoisting, fixing in position and applying a priming

coat of approved steel primer, including welding and bolted with special shaped

washers etc. complete. Hot finished welded type tubes

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,

channels, plates etc., including welding, grinding, buffing, polishing and making

curvature (wherever required) and fitting the same with necessary stainless steel

nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless

steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor

or the side of waist slab with suitable arrangement as per approval of Engineer-in

charge, (for payment purpose only weight of stainless steel members shall be

considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

G FINISHING WORK

26 Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including base

coat of water proofing cement paint applied @ 2.20kg/10 sqm.

Painting with synthetic enamel paint of approved brand and manufacture of

27 required colour to give an even shade : Two or more coats on new work over an 294 Sqm 226.25

under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and applying white cement based putty of average thickness 1 mm, of

28 approved brand and manufacturer, over the plastered wall surface to prepare the 294 Sqm 156.05

surface even and smooth complete.

12 mm cement plaster finished with a floating coat of neat cement of mix :

13.7.1 1:3 (1 cement: 3 fine sand)

H Drainage Works

Providing and laying Non Pressure NP-4 class (Heavy duty) R.C.C. pipes including

collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1

cement : 2 fine sand) including testing of joints etc. complete

19.36.1 450 mm dia RCC pipes.pe

Providing laying (to level or slopes) and jointing reinforcedconcreteLightdutynon-

pressurepipes I.S. classNP2of the following internal diameter

withcollarsandbuttendspreparedforcollarjoints including testing of joints

complete.(K) 1000mm

Providing laying (to level or slopes) and jointing reinforcedconcreteLightdutynon-

pressurepipes I.S. classNP2of the following internal diameter

withcollarsandbuttendspreparedforcollarjoints including testing of joints

complete.(K) 1200mm

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse

sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) :

3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1

cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size),

inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand)

finished with floating coat of neat cement and making Constructing masonry

Chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement :

33 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm

bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab

1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

, i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand :

graded stone aggregate 40 mm nominal size) and inside plastering with cement

mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of

neat cement complete as per standard design : 18.35.1 With common burnt clay

F.P.S.(non modular) bricks ofclass designation

Inside size 120x90 cm and 90 cm deep including Resessed MS cover with frame

33.1 (medium duty) 500 mm internal diameter, : 19.7.2.1 With common burnt clay 30 NOS 26405.5

F.P.S. (non modular) bricks of class designation

Making connection of drain or sewer line with existing manhole including breaking

into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement :

coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on

both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a

floating coat of neat cement and making necessary channels for the drain etc.

complete : 19.21.3 For pipes 350 to 450 mm diameter

S.NO DESCRIPTION QUANTITY UNITS RATE AMOUNT

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement

mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C.

35 horizontal grating with frame complete as per standard design : 19.27.1 With 30 Nos 5957.9

common burnt clay F.P.S. (non modular) bricks of

class designation

Supplying and laying of following size DWC HDPE pipe ISI marked along with all

accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete

36 with fitting and cutting, jointing etc.direct in ground (75 cm below ground level)

including excavation and refilling the trench but including sand, excluding

cushioning and protective covering etc., complete as required.

36.1 63 mm dia (OD-63 mm & ID-51 mm nominal) 900 RM 209

36.2 90 mm dia (OD-90 mm & ID-76 mm nominal) 900 RM 249

36.3 120 mm dia (OD-120 mm & ID-103 mm nominal) 400 RM 341

Providing wood work in frames of doors, windows, clerestory windows and other

frames, wrought framed and fixed in position with hold fast lugs or with dash

fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for

separately). 9.1.1 Second class teak wood

Providing and fixing to existing door frames. 9.118.1 24 mm thick factory made

PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24

mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The

styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic

brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel

screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size

20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H'

38 section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall 10.272 Sqm 2696.25

thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats.

The shutter frame filled with a uPVC multi-chambered single panel of size not less

than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall

thickness. The panels filled vertically and tie bar at two places by inserting

horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers,

complete as per manufacturer's specification and direction of Engineer-in-charge.

(For W.C. and bathroom door shutter).

9 Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm),

made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall

thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate

dimension. (Area of window upto 0.75 sqm.)

Supplying, filling, spreading & leveling bentonite clay, for all leads & lifts, all

complete as per direction of Engineer-in-charge.

Supply providing and fixing heavy duty FRP grattings 40mm thick of approved

41 colour and pattern complete as per the drawings and the directions of Engineer In- 18 sqms 4500

Supply providing and fixing floating deck / pontoon made of heavey duty HDPE

with side wall interlock, for marine (each block size 500x500x400mm) , material

having upto 80 degree C temperature resistance and loading capacity of 350kg/cu-

cm complete as per drawings and the directions of Engineer in charge

Supply providing and fixing of cut letter signages "AMBAPUR LAKE" illiminated

3D alphabets made of SS-304 grade of size 900mm high covered with 3mm arcylic

sheet in milky white colour from front and 4mm thick ACP from back side with

LEDmodule made from samsung duly cleaned & finished with all accessories inc

3000k delivering 100-lumes per watt package and SS-Frame on base and fto hold

letters complete as per drawings and the directions of Engineer Incharge

Supplying, filling, spreading & leveling gravels of size range 40 mm to 150 mm, in

44 the recharge pit, over the existing layer of boulders, in required thickness, for all 100 Cums 1088.33

leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying & laying of drainage composite for use behind walls, between two

different fills, alongside drains of road, below concrete lining of canals etc. having

thermobonding a draining core - HDPE geonet comprises of two sets of parallel

overlayed ribs integrally connected to have a rhomboidal shape with a polyethylene

film and a nonwoven geotextile having mass per unit area 130 gsm and tensile

45 strength of 8.0 kN/m that will be working as separation or protecting layer, 2244 Sqms 1166.95

geocomposite having in plane flow capacity of 0.7 L / (m.s) at hydraulic gradient of

1.0 & 20 kPa pressure and tensile strength of 13.5 kN/m , with mass per unit area of

830 gsm, at easily accessible location including top and bottom, with all leads and

lifts, manpower and machinery, materials, labour etc. complete and as directed by

Engineer - In - Charge.

S.NO DESCRIPTION QUANTITY UNITS RATE AMOUNT

Supply, Providing and fixing of 10mm multiwall clear Polycarbonate sheet,

aluminium profile, aluminium L Angle, Screws, Sealants and fixing accessories

Supplying & laying of bi-axial extruded high modulus polypropylene geogrid

coforming to MORTH SPECIFICATION for base/sub-base reinforcement having

minimum tensile strength 15kN/m in the longitudinal and transverse direction,

with 5kN/m and 7kN/m tensile strength at 2% and 5% strain respectively in the

longitudinal and transverse direction, junction efficiency not less than 95% and

with 38mm X 38mm mesh opening.

Supply Providing and fixing corten steel planters in place complete as per the

drawings and the directions of engineer in charge

Manufacturing, supplying and fixing retro reflective overhead signage boards made

up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and

encapsulated lens type heat activated retro reflective sheeting conforming to type -

III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as

per IRC 67-2001 in silver white with blue colour back ground and with high

intensity grade, pasted on substrate by pressure sensitive adhesive backing which

shall be activated by applying pressure conforming to class II of ASTM-D-4956-01

and fixing the same to the plate of structural frame work by means of suitable sized

49 aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the 252 Sqms 5879.9

periphery as well as in two vertical rows along with theft resistant measures,

including the cost of painting with two or more coats of epoxy paint in grey colour

on the back side of aluminium sheet including appropriate priming coat. The rate

includes the cost of rounding off the corners, lowering down the structural frame

work from the gantry, fixing and erecting the same in position all complete as per

drawings, specification and direction of the engineer-in charge.(Structural frame

work including M.S. plate to be provided separately. Rectangular area of the sheet

only shall be measured for payment). 16.60.1 Overhead informatory road signage

Regulatory / Mandatory Sign :-Providing and fixing sign boards made out of 2mm

aluminium sheet / 4mm ACP (Aluminum composite Panel); size 60 cms. Dia

Circle as per design of IRC-67- 2012. Pre treated with phospheting process & acid

etching; coated with one coat of epoxy primer and two coats of best quality epoxy

paint ; reflectorised with High Intensity Prismatic Grade retro refiectivesheeting of

Type-4 as per ASTM D-4956 and latest M.O.S.T.Specifications; 3.6mtr long stand

post of Iron Angle 75 x 75 x 6mm / 65NB Circular MS Pipe as required and frame

50 fabricated from suitable size iron angle of 35 x 35 x 3mm; painted with bestquality 25 Each 3505.07

epoxy coatings in black and white bends. The details of symbol for each board shall

be as per the instruction of engineer in charge. The fixing at site shall be in 1:2:4 CC

blockof size 45 x 45 x 60 Cms. for each leg including excavation, curing

etc.complete under the supervision of engineer in charge. A warranty for 7 years for

the Retro reflective sheeting from original manufacturer & a certified copy of 3 year

outdoor exposure test report from third party test lab for the product offered shall be

submitted by contractor. (B) Class-B Type-4 Retro Reflective sheeting.

Providing and fixing sign boards made out of 2mm aluminium sheet / 4mm ACP

(Aluminum composite

Panel); size 80 x 60 cms rectangular as per design of IRC-67-2012. Pre treated with

phospheting process & acid etching; coated with one coat of epoxy primer and two

coats of best quality epoxy paint ;reflectorised with Micro Prismatic Grade retro

refiectivesheeting of Type-11 as per ASTM D-4956 and latest

M.O.S.T.Specifications; 3.6mtr long stand post of 75 x 75 x 6mm / 65NB Circular

MS Pipe as required and frame fabricated from suitable size iron angle of 35 x 35 x

51 3mm; painted with bestquality epoxy coatings in black and white bends. The details 14 Each 5848

of symbol foreach board shall be as per theinstruction of engineer in charge. The

fixing at site shall be in 1:2:4 CC blockof size 45 x 45 x 60 Cms. for each

leg.including excavation, curing etc.complete under the supervision of engineer in

charge. A warranty for 10 years for the Retro reflective sheeting from original

manufacturer & a certified copy of 3 year outdoor exposure test report from third

party test lab for the product offered shall be submitted by contractor. (A) Class-C

Type-11 Retro Reflective sheeting

K Sanitary and Plumbing

Providing and fixing soil waste and vent pipes: 100mm diameter centrifugally cast

(spun) iron S&S pipe as per IS:3989.

Providing and fixing plain bend of required degree: 100mm centrifugally cast (spun)

iron S&S as per IS:3989.

S.NO DESCRIPTION QUANTITY UNITS RATE AMOUNT

Providing and fixing G.I. pipes complete with G.I. fittings and clamps including

54 90 Metre 667

cutting and making good the walls etc., (Internal work) :32mm nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps including

cutting and making good the walls etc., (Internal work) : 50mm nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of

approved quality. 32mm diameter pipe

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of

approved quality.50mm diameter pipe

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH-

40) for Hot & cold water including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or

shall be concealed as directed including necessary fittings etc. including testing of

pipe and joints and fixing the same with adhesive solvent, including cost of all

Providing laying and jointing in true line and level 32mm dia. U.P.V.C. Pipe ( SCH-

40) for Hot & cold water including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or

56.1 shall be concealed as directed including necessary fittings etc. including testing of 30 Metre 117.97

pipe and joints and fixing the same with adhesive solvent, including cost of all

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR

13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of

following dia. nominal bore tube fittings and clamps including making good the

wall, ceiling and floor etc. complete.[A] 15 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR

13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of

following dia. nominal bore tube fittings and clamps including making good the

wall, ceiling and floor etc. complete. [B] 20 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR

13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of

following dia. nominal bore tube fittings and clamps including making good the

wall, ceiling and floor etc. complete. [C] 25 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR

13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of

following dia. nominal bore tube fittings and clamps including making good the

wall, ceiling and floor etc. complete. [D] 32mm.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality

(screwed end) :32 mm nominal bore.

Providing and fixing ball (brass) valve of approved quality. High or low pressure,

with plastic floats complete: Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes, having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m

spacing. This includes jointing of pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and making good the same including testing

of joints complete as per direction of Engineer in Charge.Concealed work,

including cutting chases and making good the walls etc.: 25 mm nominal bore

Constructing brick masonry chamber for underground C.I. Inspection chamber and

bends with bricks having crushing strength not less than 35Kg/Cm2 in C.M. 1:5

C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total

weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt.

frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded

stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick

with cement mortar 1:3 finished smooth with a floating coat of neat cement on

walls and bed concrete etc. complete.(ii) Inside dimensions 500mm x 700 mm and

450mm deep for pipe line with one or two inlets.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of

61 required shape and approved quality 19.19.1 L D- 2.5 H D - 20Circular shape 560 20 Each 1675.70

mm internal diameter (For U G tanks)

Providing and fixing white vitreous China pedestal type water closet (European

Type) with seat and lid, 10 litre low level white vitreous china flushing cistern &

C.P flush bend with fittings and C.I brackets, 40mm flush bend, overflow

62 arrangement with special standard make and mosquito proof coupling of approved 16 Each 8006.60

municipal design complete including painting of fittings and brackets, cutting and

making good the walls and floors where required. W.C pan with ISI marked white

solid plastic seat and lid.

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S.

brackets painted white including sutting holes, fittings and making good the

63 same.(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) In 12 Each 1470.19

64 Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. 16 Each 142.85

S.NO DESCRIPTION QUANTITY UNITS RATE AMOUNT

65 Providing and fixing C.P. brass waste for washbasin or sink. (A) 32mmdia. 12 Each 67.24

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of

66 approved quality) complete with 6 mm thick hard board ground fixed to wooden 12 Each 1607.95

cleats with C.P. brass screws and washers complete.

67 Providing and fixing toilet paper holder.(A) C.P. Brass 16 Each 423.75

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to

wooden plugs with C.P. brass scews.(B) 600mm x 20mm size.

Providing and fixing C.P. brass long body bib cock of approved quality

69 conforming to IS standards and weighing not less than 690 gms.15 mm nominal 6 Each 798.95

Providing and fixing C.P brass angle valve for basin mixer and geyser points of

approved quality confirming to IS:8931: 15 mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth

71 102mm, height of 75mm with concealed fitting arrangements, weighing not less 6 Each 111.45

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-Graded

stone aggregate 40mm nominal size) bedding for stoneware pipes of following

72 internal diameters with necessary formwork and curing complete.(B) 150mm dia. 150 Metre 211.59

(166mm Ave. bed thickness)

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and

73 water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard 5 Each 1279.40

weight.(i) Square mouth traps.(B) 150mm x 100mm size P or R type

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand :

4-graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-

cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick

with Cement Mortar 1:3 (1-Cement : 3-coarse sand) finished with a floating coat

of neat cement and making channels in cement concrete 1:2:4 mix (1-Cement :2-

Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete

including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep

including C.I. cover with frame size 560mm diameter total weight of cover and

frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A)

With 230mm thick walls of brick msonry using brick having crushing strength not

less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (2) B

type depth 1.50 Metre for 150mm diameter sewer.

Extra for depth for manholes:Size 90 x 80 cmWith common burnt clay F.P.S. (non

modular) bricks of class designation

Providing orange colour safety foot rest of minimum 6 mm thick plastic

encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS :

having minimum cross section as 23 mmx25mm and over all minimum length

mm and width as 165mm with minimum 112 mm space between protruded legs

having 2 mm tread on top surface by ribbing or chequering besides necessary and

76 adequate anchoring projections on tail length on 138 mm as per standard drawing 2 Each 553.70

and suitable to with stand the bend test and chemical resistance test as per

specifications and having manufacture's permanent identification mark to be visible

even after fixing, including fixing in manholes with 30x20x15 cm cement concrete

block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal

size) complete as per design.

Providing and fixing white vitreous china battery based infrared sensor operated

urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water

77 (250 ml & 500 ml consumption), having water inlet from back side, including fixing 4 each 7979.20

to wall with suitable brackets all as per manufacturers specification and direction of

Engineer-in-charge.

Providing and fixing Inlet Fitting for Urinal trap, formed out of 110 mm PVC pipe

with multiple side inlets formed with saddle pieces, suitable for 40, 50 and 63 mm

78 dia side connections as per standard detail and support through galvanized steel 12 NOS 349

support from slab or set in cement concrete mix 1:2:4 including cutting and making

good the walls and floors wherever required.

Providing and fixing Heavy Class SS grating of approved design including setting

79 in floor with cement motor to match with floor finish as per architect requirement 8 NOS 167

suitable for waster and FT, UT & FD. Size 100 mm X 100 mm

Providing and fixing rectangular high density polyethylene / FRP water storage

loft tank with cover, conforming to ISI : 12701, colour of opaque white or as

80 approved by Engineer-in-charge. The rate includes making necessary holes for inlet, 15000 Ltrs 11

outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be

paid separately.

S.NO DESCRIPTION QUANTITY UNITS RATE AMOUNT

Boring/drilling bore well of required dia for casing/ strainer pipe, bysuitable

method prescribed in IS: 2800 (part I), including collecting samples from different

strata, preparing and submitting strata chart/ bore log, including hire & running

81 charges of all equipments, tools, plants & machineries required for the job, all 400.00 Mtrs 825.7

complete as per direction of Engineer-in-charge, beyond 90 metre depth below

ground level. 300mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well,

unplasticized PVC medium well casing (CM) pipe of required dia, conforming to

82 IS: 12818, including required hire and labour charges, fittings & accessories etc. all 400.00 Mtrs 1113.35

complete, for all depths, as per direction of Engineer -in-charge. 23.3.1 200 mm

nominal size dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply including all CPVC plain & brass threaded

83 fittings This includes jointing of pipes & fittings with one step CPVC solvent 400.00 Mtrs 6822.7

cement, trenching, refilling & testing of joints complete as per direction of

Engineer in Charge. External Works 150mm Dia

Providing & making Gabion structure with Mechanically Woven Double Twisted

Hexagonal Shaped Wire mesh Gabion Boxes as per IS 16014:2012,MORTH Clause

2500, of required size, Mesh Type 10x12 (D=100 mm with tolerance of ± 2%) Zinc

coated, Mesh wire diameter 3.0 mm, mechanically edged/selvedged with

84 partitions at every 1m interval and shall have minimum 10 numbers of openings 1848.00 Cums 4178

per meter of mesh perpendicular to twist, tying with lacing wire of diameter

2.2mm, supplied @ 3% by weight of Gabion boxes, filled with boulders with least

dimension of 200 mm, as per drawing, all complete as per direction of Engineer-in-

Deawtering by pumping set of required capacity including temporary

85 platormcarting pumping at site and fixing the same in position including all 88533.25 hp 18.51

accessories, labour, fuel etc. complete

Supply & Fixing of Double bucket Dustbin, of Capacity (liters) 40, Size (L x W x D

86 mm) 1180 x 1000 x 1000 (mm). Bin will be manufactured in complete laser process 10.00 Each 6620.21481

to provide accurate and neat borders. Brand: Sintex, Chevron or Equivalent.

Surface dressing on old surface with hot bitumen of grade VG - 10 of approved

quality using 1.95 kg of bitumen per sqm with 1.50 cum of stone chippings 11.2 mm

nominal size per 100 sqm of road surface, including consolidation with road roller

of 6 to 8 tonne capacity, etc. complete.

Providing panel wall for dry stone pitching inuncourased rubblemasonary with had

stone of approved quality in cement. mortar 1.5 including curing etc, complete.

Supply providing and laying of micro cement flooring as per required texture and

colour as per acrchitectural drawing and directions of engineer in charge

Providing and laying rough chiseled dressed stone flooring over 20mm thick base

of cement mortar 1:5 (1-Cement : 5-coarse sand) or L.M. 1:1.5 including pointing

with cement mortar 1:2 (1- cement : 2-stone dust) etc. complete. (B) 40mm thick (

Red Sand Stone)

Supplying, filling, spreading & leveling murrum, in required thickness, for all leads

& lifts, all complete as per direction of Engineer-in-charge.

S.NO DESCRIPTION QUANTITY UNITS RATE AMOUNT

Contour surveywork for prepaing contourmaps by taking cross-section at

every 30M. intervals including all, labour materials and instruments.

Surveying for site works including ranging, chaining, pegging leveling and

93 compass surveying including all labour materials and instruments 30.0 Km 3046.05

Operation and Maintainance

Comprehencive maintainance including maintaning and operating and

replacing all assets, if necesaary install ingarden including green space

and all type of civil, mechanical and electrical installation work and

irrigation system and providing superviser, watchmans, sweeper etc and

94 Redevelopment of lawn, scrub,tree, etc as required And cleaning of external 12.00 Month 154660.00

& internal path way, Gajiba, Jogging Track, all benches, all dustbins, watering

plants all overhead and under ground tanks, all stone floors and dedos and all

garden area as specified and by engaging labour force with cost of material and

labour and all taxes for all works as directed by engineer in charge.

O&M For 1st Year

O&M For 2nd Year(5% Escalation on Previous Year)

O&M For 3rd Year(5% Escalation on Previous Year)

O&M For 4th Year(5% Escalation on Previous Year)

O&M For 5th Year(5% Escalation on Previous Year)

Total O & M Cost for 5 Years

GRAND TOTAL (In Rs.)

GRAND TOTAL (In Rs.)

I/We am/are willing to carry out the work at ________% above/below percent (should be written in figures and words) of the estimated rate mentioned above. Amount of my / our

tender works out as under .

Estimated amount put to tender Estimated amount put to tender

Deduct____% below Add____% Above

In words In words

1 All work shall be carried out as per Public Works Department Handbook and other specifications of Division or as directed.

2 All columns in the Schedule should be filled in ink and the total of the entire in the last columns should be struck by the contractor under his signature.

3 Rates quoted include clearance of site (prior commencement of work and at its close) in all respects and hold good for work under all conditions, site, moisture, weather

4 To be continued on additional sheets, if found necessary.

5 The Labour Cess will be deducted as per prevailing rules i.e.1% of the work done.

6 GST is applicable seperatly for all type of works by the Client (Total Tender Cost is without GST).

7 The bituminous work shall be carried out by the contractor or as under by utilizing.

8 For abnormal high or law rates payment of such items shall be regulated as per Govt. Circular letter No. Parach-102008-61-S dated 27-11-2008 attached with tender

9 From dt. 1-7-2017 GST is applicable hence Agency should quote price accoringly. Any dispute regarding this will not be considered by GMC.

10 The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for which no extra payment shall be made.

11 GST and Income tax TDS will be deducted at a source while making payments of bills.

12 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017 Cement Consumption/16/C Date:11/05/2017 as

stated in S.O.R. therefore in R.C.C. items where there is a change as per actual mix design the cost of difference of cement consumption have been deducted from the

rate of original item at the rate of input rate mentioned in SOR used for preparation of Estimate.

Signature of Contractor

The Deputy Commissioner

Gandhinagar Municipal Corporation (GMC),

Based on DSR ITEM NO

Provding and fixing stainless steel bollard in position 125 mm dia Bollards 1000 mm high of required shape

including all the ss fitting etc.

S.no DSR NO Description Quantity Unit Rate Amount

Cost For P/L one n.

SS BOLLARD OF 1M CLEAR

HEIGHT OF GRADE 304 (Rates

ii 2205 STEEL CARRIAGE PER KG 4.5 Kg 0.164

iii 4.20A.1.3 CONCRETING OF M20Grade 0.002 Cum 9005.85

iv Labour Hire Charges

iv.i 9988 Carriage and Fixing charges 1 Ls 2.27

Add 1% Water Charges (W-A) on "A"

Add 15% CPOH on "B"

Add 1% Cess on "C"

Cost For P/L one n.

Providing and fixing SS DOUBLE POLE 14X24 INCH GRADE 202, WEIGHT 13.000 KG

APPROX. CAPACITY 40+40 LTR OPEN TYPE SHEET THICKNESS 0.5 mm APPROX.

SSR NO Description Quantity Unit Rate Amount

SS dustbins 60+60ltr capacity OF GRADE

(Rates from Konnect Infratech Pvt Ltd)

DSR- 2205STEEL CARRIAGE PER KG 13 Kg 0.164

Labour Hire Charges

LR_36 MAZDOOR_MALE LS Day 350

0114 BELDER 2 Day 736

0128 MATE 0.48 DAY 816

9999 Sundries 1.13 ls 2.27

Add 10% CPOH on "B"

Cost For P/L one n.

Based On DSR item no

Supplying, filling, spreading & leveling gravels of size range 40 mm to 150 mm,

AOR-06 in the recharge pit, over the existing layer of boulders, in required thickness,

for all leads & lifts, all complete as per direction of Engineer-in-charge.

S.no DSR NO Description Quantity Unit Rate Amount

Gravels / Aggregate

7753 40mm nominal size and 89.1 cum 850

2215 Carriage 0 cum 122.08

Labour Hire Charges

0114 BELDER 10 Day 736

0128 MATE 0.48 DAY 816

Add 1% Water Charges (W-A) on "A"

Add 15% CPOH on "C"

Cost For P/L 89.10cums.

Cost For P/L 1cums.

Providing and fixing Inlet Fitting for Urinal trap, formed out of 110 mm PVC pipe with multiple

side inlets formed with saddle pieces, suitable for 40, 50 and 63 mm dia side connections as per

standard detail and support through galvanized steel support from slab or set in cement concrete

mix 1:2:4 including cutting and making good the walls and floors wherever required.

Unit Qty. Rate Amount

Sl. No. Description

Detail of Cost for Inlet Fitting

A Cost of Inlet Fitting Nos. 1 484.40

Less Discount @ 50%

B Add for Solvent etc. 5%

Plumber (Fitter 1st class) Day 0.06 733.00

E Add 1% for water charges

F GST @ 18% (multiplying factor

G Add 15% for Contractor's profits

Providing and fixing Heavy Class SS grating of approved design including setting in floor with

AOR-09 cement motor to match with floor finish as per architect requirement suitable for waster and FT, UT &

FD. Size 100 mm X 100 mm

Unit Qty. Rate Amount

Sl. No. Description

Detail of Cost for SS Grating

A Cost of SS Grating Nos. 1 125.00

Plumber (Fitter 1st class) Day 0.03 733.00

E Add 1% for water charges

F GST @ 18% (multiplying factor

G Add 15% for Contractor's profits and

Based on DSR Item No 16.91.1

Providing and laying factory made chamfered edge Cement Concrete paver blocks

in footpath, parks, lawns, drive ways or light traffic parking etc, of required

strength, thickness & size/ shape, made table vibratory method using PU mould, laid

in required colour & pattern over 20mm thick mortar, compacting and proper

embedding/laying of inter locking paver blocks into the sand bedding layer through

vibratory compaction by using plate vibrator, filling the joints with sand and cutting

of paver blocks as per required size and pattern, finishing and sweeping extra sand.

complete all as per direction of Engineer-in-Charge

S.no DSR NO Description Quantity Unit Rate Amount

60MM Thick M-35 paver

3.9 Mortar rate as per item no 3.9 0.5 Cum 4211.7

Labour Hire Charges

0114 Belder 1 Day 736

0115 Coolie 0.5 Day 736

9999 Sundries 25 ls 2.27

0123 Mason (1st Class) 0.5 Day 897

0124 Mason (2nd Class) 0.5 Day 816

Add 1% Water Charges (W-A) on "A"

Add 15% CPOH on "C"

Cost For P/L 10sqm.

Cost For P/L 1.0sqm.

Based On DSR item no

Supplying, filling, spreading & leveling bentonite clay, for all leads & lifts, all complete as per

direction of Engineer-in-charge.

S.no DSR NO Description Quantity Unit Rate Amount

7183 Bentonite clay @593kg/cum 52836.3 Kg 3.05

Labour Hire Charges

0114 BELDER 10 Day 736

0128 MATE 0.48 DAY 816

Add 1% Water Charges (W-A) on "A"

Add 15% CPOH on "C"

Cost For P/L 89.10cums.

Cost For P/L 1cums.

Supply, Providing and fixing of 10mm multiwall clear Polycarbonate sheet, aluminium profile,

aluminium L Angle, Screws, Sealants and fixing accessories

S.no DSR NO Description Quantity Unit Rate Amount

10MM MULTIWALL (PDM

i EXTRUSIONS PVT LTD)

ii CARRIAGE 0 Kg 0.164

iii 1024 J or L hooks 10mm dia 125mm long 6 No 9

1143 steel beading box type 2 RMT 27

iv Labour Hire Charges

iv.i 0114 Belder (DAR 21.18.1) 0.9 Day 340

iv.ii 0119 Glazier (DAR 21.18.1) 0.9 Day 370

Add 1% Water Charges (W-A) on "A"

Add Gst @14.05% on B

Add 15% CPOH on "C"

Cost For P/L one n.

Based On DSR item no

Supplying, filling, spreading & leveling murrum, in required thickness, for all

leads & lifts, all complete as per direction of Engineer-in-charge.

S.no DSR NO Description Quantity Unit Rate Amount

Murrum 89.1 cum 76

2215 Carriage 0 cum 122.08

Labour Hire Charges

0114 BELDER 10 Day 736

0128 MATE 0.48 DAY 816

Add 1% Water Charges (W-A) on "A"

Add 15% CPOH on "C"

Cost For P/L 89.10cums.

Cost For P/L 1cums.

RATE ANALYSIS-O&M-Ambapur Lake Near Vav

Comprehencive maintainance including maintaning and operating and replacing all assets, if necesaary install ingarden including green space and all type of civil, mechanical and

electrical installation work and irrigation system and providing superviser, watchmans,sweeper etc and Redevelopment of lawn, scrub,tree, etc as required And cleaning of external &

internal path way, Gajiba, Jogging Track, all benches, all dustbins, watering plants, toilet clening with using material all overhead and under ground tanks, all stone floors and dedos and

all garden area as specified and by engaging labour force with cost of material and labour

and all taxes for all works as directed by engineer in charge.

Sr. Description Shift No Days Qty Rate Per Amount

1 Supervisor (all over work) 1 1 12 12.00 522.50 DAY

2 Electrician (all over work) 1 1 6 6.00 522.50 DAY

3 Labour cum Sweeper 1 2 30 60.00 500.50 DAY

4 Gardner 1 2 30 60.00 510.50 DAY

5 Providing watchman services at designated points as per instruction of 3 1 30 90.00 510.50 DAY

engineer in charge

Comprehencive maintainance including maintaning and operating and

replacing all assets, if necesaary install ingarden including green

space and all type of civil, mechanical and electrical installation work

and irrigation system and providing superviser, watchmans, sweeper etc and

Redevelopment of lawn, scrub,tree, etc as required And cleaning of

1 external & internal path way, Gajiba, Jogging Track, all benches, all

dustbins, watering plants all overhead and under ground tanks, all stone

floors and dedos and all garden area as specified and by engaging

labour force with cost of material and labour and all taxes for all works as

directed by engineer in charge. (1% of total project cost)

Total Project Cost of (Landscap+Horticultire+ Electric+irrigation)

Maintanance 1% of Total Cost

Maintanance Cost per Year

Maintanance per month 24456.91 1.00 24456.91 Month

Add 10% Contractor Profit

Operation And Maintainance Cost For 5 Years for Lake at Ambapur in GMC Area

Sr.No. Description Qty Unit Rate Amount

Comprehencive maintainance including maintaning and

operating and replacing all assets, if necesaary install

ingarden including green space and all type of civil,

mechanical and electrical installation work and irrigation

system and providing superviser, watchmans, sweeper etc and

Redevelopment of lawn, scrub,tree, etc as required And

cleaning of external & internal path way, Gajiba, Jogging

Track, all benches, all dustbins, watering plants all overhead

and under ground tanks, all stone floors and dedos and all

garden area as specified and by engaging labour force with

cost of material and labour and all taxes for all works as

directed by engineer in charge. (1% of total project cost)

O&M For 1st Year

O&M For 2nd Year(5% Escalation on Previous Year)

O&M For 3rd Year(5% Escalation on Previous Year)

O&M For 4th Year(5% Escalation on Previous Year)

O&M For 5th Year(5% Escalation on Previous Year)

Total O & M Cost for 5 Years

NAME OF PROJECT:- PROPOSED LAKE AND GARDEN DEVELOPMENT (VILLAGE

TALAV) INCLUDING 5 YEARS O & M AT AMBAPUR IN GANDHINAGAR - FOR

GANDHINAGAR MUNCIPAL CORPORATION

ESTIMATE FOR ELECTRICAL WORK

DSR / AOR / SOR NON SCHEDULE

S. NO. DESCRIPTION AMOUNT WITHOUT AMOUNT

GST WITHOUT GST

A CABLE,EARTH PIT & FEEDER PILLAR

2 CABLE LAYING AND END TERMINATIONS

3 FEEDER PILLER

5 Turnkey Factor

B POLE & FIXTURES 975880.5325

C BUILDING (Toilet , Guard room & Restaurant)

1 DISTRIBUTION BOARD

2 INTERNAL WIRING

3 SITC FANS & LIGHT FIXTURES

AUDIO & CCTV SYSTEM 1269994

H SUBMERSIBLE PUMPS

I WATER COOLER & RO

ESTIMATE FOR ELECTRICAL WORK

SUBHEAD:ELECTRICALWORK

Description Unit Qty Rate Total Amount Remarks

Description Unit Qty Rate Total Amount Remarks

A SCHEDULEITEMS

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing

Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion

free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection

terminal dia of 12mm with constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for following type of applications with

chamber and heavy duty cover. (A)(approved make OEM has to submit test certificate SOR-

including value of earth resistance of installation duly stamped and signed by agency and 2025-26

officer Incharge has to ensure the value of earthing resistane mentioned in test

Certificate) & having back filling compound of (B) Inner chemical (CCM Compound)-

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no

load & dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound

should be capable to retain moisture for long time Necessary test report must be

submitted by Agency.

(c) For Electrical Installation covering Transformer Neutrals, Lightning arrester

Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA) i.e SOR-

independent Earthing in normal soil. Length of Pipe : 3.00 mtrs 2025-26

Back filling Compound :2 nos Bags of 25 Kg.

1.3 3-14-5 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. KG 1500 77

TOTALFOREARTHINGCARRIEDOVERTOSUMMARY

CABLE SUPPLY, LAYING, DWC HDPE PIPE, CHAMBER (MANHOLE) AND END

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium

2.1 4-3-3. conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench /

pipe of following size of cables

2.2 (D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core) meter 850 275

2.3 (B) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core) meter 590 218

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / Solid

3 4-3-4. Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing

trench / pipe of following size of cables

3.1 (c) 4 core 10 Sq. mm meter 1500 139

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid

4 4-4-4./4-4-2. Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing

trench / pipe at road crossing or floor of following size of cables.

4.1 (C) 4 core 6 Sq. mm meter 850 505

4.2 (C) 3 core 6 Sq. mm meter 980 392

4.3 (B) 3 core 4 Sq. mm meter 1540 285

4.4 (A) 3 core 2.5Sq. mm meter 1160 213

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same

material at required depth in existing trench for laying of cable. below ground / road

surface for enclosing cable (A)50 mm outer dia

5.1 (A) 50 mm outer dia meter 3570 62

5.2 (C) 90 mm inner Dia. meter 590 95

5.3 (D) 120 mm inner Dia. meter 850 136

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4

(1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter,

160 mm bottom diameter and 180 mm deep ( inside) with

chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone

aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1

cement : 5 fine sand : 10 graded stone aggregate 40 mm1461

nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand)

mm thick, finished with a floating coat of neat cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 DSR Rate

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC

7 4-6-1. insulated armoured cable complete with out going tails, insulating tape etc for following

size of cables.

2 to 4 core 2.5 / 4 Sq. mm SOR-

2 to 4 core 6 Sq. mm SOR-

7.3 (C) 2 to 4 core 10 Sq. mm Set 50 38

Providing and, fixing heavy duty flange type brass double compression type cable gland

8 4-6-3. with rubber ring for PVC insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables.

8.1 (C) 3 & 1/2 core 70 Sq. mm Set 6 102

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single

core cable in the existing surface / recessed steel / PVC conduit as required.

TOTAL FOR CABLE LAYING, DWC HDPE PIPE, CHAMBER (MANHOLE) AND END

TERMINATIONS CARRIED OVER TO SUMMARY

B NONSCHEDULEITEMS

FEEDER SECTION PILLAR TYPE-A (3-4 FEEDER)

Supply, installation, Testing and commissioning of the Feeder Section Pillars as per

specifications, IS and Drawings The unit rate for each item shall include: Call for final

inspection prior to dispatch. Delivery of the fidder pillar / section pillar to site. Shifting of

the fidder / section piller from site to store to the suitable location. Shifting & Fixing of

Section Pillar. Assembly and wiring of component supplied separately. Installation of

section piller to including removing old section pillar. Earthing all components, frame etc.

Rate As per to a common internal earth bar. M.S. parts should painted with powder coating. Supply &

AMC fixing all accessories and supporting structure. Supply & fixing of M.S. 40 x 40 x

channels for fixing the panels. Connection, testing and commissioning Checking of

internal connection and wiring, operation of switches, starter, MCCB, relays, contactors

etc. Supply of necessary tools, hardware, testing equipment etc. etc. Electrical contractor

shall carry out the insulation test at site and all the readings shall be submitted in

duplicate to the consultant or engineer-in- charge. Approval from State Electricity Board

10.1 FEEDER SECTION PILLAR TYPE-B (2-3 FEEDER)

Supply, installation, Testing and commissioning of the Feeder Section Pillars as per

specifications, IS and Drawings The unit rate for each item shall include: Call for final

inspection prior to dispatch. Delivery of the fidder pillar / section pillar to site. Shifting of

the fidder / section piller from site to store to the suitable location. Shifting & Fixing of

Section Pillar. Assembly and wiring of component supplied separately. Installation of

section piller to including removing old section pillar. Earthing all components, frame etc.

Rate As per to a common internal earth bar. M.S. parts should painted with powder coating. Supply &

AMC fixing all accessories and supporting structure. Supply & fixing of M.S. 40 x 40 x

channels for fixing the panels. Connection, testing and commissioning Checking of

internal connection and wiring, operation of switches, starter, MCCB, relays, contactors

etc. Supply of necessary tools, hardware, testing equipment etc. etc. Electrical contractor

shall carry out the insulation test at site and all the readings shall be submitted in

duplicate to the consultant or engineer-in- charge. Approval from State Electricity Board

11.1 TOTAL FOR FEEDER PILLAR CARRIED OVER TO SUMMARY

12 Turnkey Factor

Providing of turnkey factor to the concirn eletric department as per the load to be opretor

ESTIMATE FOR ELECTRICAL WORK

SUBHEAD:ELECTRICALWORK

Description Unit Qty Rate Total Amount Remarks

Description Unit Qty Rate Total Amount Remarks

A SCHEDULEITEMS

(b) LED Bollard fittings of minimum height 600 mm & dia.100mm having polycarbonate

clear/milky diffuser mounted on 3mm thick aluminium finished powder coated pipe with SOR-

base plate 160x160mm with erection by M8x75mm fastner with required RCC 2025-26

foundation.IP65 for 9 to 20 watt ,surge-4kv cat- III

(C) Post Top Lantern LED fitting comprises of finish cast aluminum spigot and spun aluminum

2 2-16-2. canopy fixed with opal polycarbonate, pipe arrangement for vertical mounting driver and

accessories wired upto terminal block.IP

2.1 (ii)32-40W Cat-III on 4M pole Each 25 6193

Supply of approved make frp/grp pole having followiing specifications :

FRP/GRP pole made by centrifugal moulding process using thermoset resin polyester/epoxy

resin system having minimum glass content 45.0%.The pole should be in one pieceand tapered

round in shape,having smooth outside surface finish and should be totally fre from

corrosion as well as non conductive and shock proof. Pole should be provided with FRP/GRP

base bracket dully fabricated from metal(M.S) and dully claded with FRP/GRP material to avoid

any metal exposer and painted with PU paint. Pole should mechanical properties i.e

Specfic gravity (ASTM D 792) 1.3-1.8 Kg/m3, 2. Glass Content % by weight (ASTM D 2584)

45.0 -55.0%, 3. Water absorption (ASTM D 570) <0.5%, 4. Tensile Strength(ASTM D 638)

200+/-50Mpa, 5. Flexural strength (ASTM D 790) 250+/-50Mpa, 6. Compressive Strength (ASTM SOR-

D 695) 200+/-50MPa, 7. Yeild Strength(ASTM D638) 250 +/-50MPa. Pole should be flame 2025-26

retardant as per IS 6746.Resin used shall be UV resistance and pigmented. Pole should be

painted with first coat of epoxy primer and then two coat of highly weather resistance

polyurethen paint to ensure proper addhesion of the paint.Minimum thickness shall be 80 to

100 micron.Defelection of the pole shall not exceed more than 10.0 % of the length of the pole

for the given load.Pole should be generally made as per the dimensional data, performance

criteria and some interchagebility features of poles as per the standard ANSI C123.20 latest

version of ASTM D 923/01 including cable termination box with necessory

accessories.The size of pole and type of installation with foundation , Anchor Base & Internal

junction box as per the

Pole should be flame retardant as per IS 6746.Resin used shall be UV resistance and pigmented.

Pole should be painted with first coat of epoxy primer and then two coat of highly weather

resistance polyurethen paint to ensure proper addhesion of the paint.Minimum thickness shall

be 80 to 100 micron.Defelection of the pole shall not exceed more than 10.0 % of the length of

the pole for the given load.Pole should be generally made as per the dimensional

data,performance criteria and some interchagebility features of poles as per the standard ANSI

C123.20 latest version of ASTM D 923/01 including cable termination box with necessory

accessories.The size of pole and type of installation with foundation , Anchor Base & Internal

junction box as per the manufacturer details and site requirement .

3.1 (3) 'B' class (Heavy Duty) frp/grp pole suitable for base plate mounting

[B] Overall Length of 4.0 meter, Average thickness : 4mm, Top/Bottom Outside Dia. 76/143mm

+/-2.Weight of Pole 10.0 Kg approx. (Without base) Metal Anchor Base dully frp claded (Size : Each 0 14606

CONTI (3) B 2025-26

290 Ø * 12mmthk , Mounting hole PCD 240mm * 4 nos. of 16 Ø hole)

[D]Overall Length of 6.0 meter, Average thickness : 5mm, Top/Bottom Outside Dia. 76/176mm

3.2 +/-2.Weight of Pole 19.0 Kg approx. (Without base) Metal Anchor Base dully frp claded (Size : Each 25 21318

CONTI (3) D 2025-26

340 Ø * 12mmthk , Mounting hole PCD 285mm * 6 nos. of 20 Ø hole)

Providing 1:2:4 cement concrete foundation & 70 % PCC from bottom including excavation for

the pole of size 45 x 45 x 100 cm. Deep in below ground level with plinth of 45 cm x 45 cm (or SOR-

45 cm dia x 45 cm) high upper ground level with necessary curing and finishing in approved 2025-26

manner. ( for 4 & 6 mtr pole)

Providing cement concrete.for foundation or for concrete filling in 1:2:4 ratio with 20 to 25 mm SOR-

stone metal duly plastered with necessary curing for pole muffing or any other purpose. 2025-26

Pole should be flame retardant as per IS 6746.Resin used shall be UV resistance and

pigmented. Pole should be painted with first coat of epoxy primer and then two coat of highly

weather resistance polyurethen paint to ensure proper addhesion of the paint.Minimum

thickness shall be 80 to 100 micron.Defelection of the pole shall not exceed more than 10.0 %

6 of the length of the pole for the given load.Pole should be generally made as per the

dimensional data,performance criteria and some interchagebility features of poles as per the

standard ANSI C123.20 latest version of ASTM D 923/01 including cable termination box with

necessory accessories.The size of pole and type of installation with foundation , Anchor Base &

Internal junction box as per the manufacturer details and site requirement .

6.1 (3) 'B' class (Heavy Duty) frp/grp pole suitable for base plate mounting

[H] Overall Length of 10.0 meter, Average thickness : 9mm, Top/Bottom Outside Dia. 76/244mm

6.2 +/-2.Weight of Pole 62.0 Kg approx. (Without base) Metal Anchor Base dully frp Each 2 43801

claded (Size : 450 Ø * 18mmthk , Mounting hole PCD 390mm * 6 nos. of 20 Ø hole

Supplying and erecting LED street light / Flood light fittings with High power White LEDs

wattage of 3 Watt and above assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing with smooth finish powder coated

and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire

7 2-16-2. efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM- 79 & LM-80

certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line SOR-

supply with over-voltage protection. 2025-26

(v) above 160 to 200 watts Cat-III SOR-

(v) above 200 to 250 watts Cat-III SOR-

Supplying, erecting, testing, commissioning approved make M.S. Polygonal High Mast Pole

having following general Specification. (a) Polygonal Section fabricated from M.S. Plate confirms

BSEN 10025 & Hot deep galvanized minimum 65/86 micron (as per IS 2629 /1985) Lantern

carriage with ring and rubber lines for erection of luminaries of suitable site. (b) Maximum

telescopic section not more than four (c) Double drum gear pipe motorized winch with 6mm

dia S.S. Rod (For 16 mtr and above size) (d) Approved make L.E.D. aviation light = 1 No.

6.8.1. Lightening arrestor = 1 No. with necessary wiring of 2.5 sq.mm 5 core ISI copper cable

Unarmoured. (e) Bottom most section suitable for mounting reversible motor and switchgears

having door not more than 1400mm x 300mm with waterproof gasket & hinges & locking

arrangement. (f) Pole structure comprises suitable size of reversible motor, cable and necessary

switchgears with control panel.

(g) bottom section shall have suitable size of thickness supports ribs foundation bolts nuts

etc. (h) Item not comprises the cost of lanterns. (i) Necessary Cement Concrete foundation as

per IS including testing & commissioning of the entire structure for following size of High Mast

[3] High Mast 16 Mtr. TOP A/F 150 mm, BOTTOM A/F 450 mm, No. of Sec. No. - 2, Bottom

Thickness - 4 mm, Top Sec. 3 mm, Size of Base Plate - dia.560 mm x 20 mm thick, Foundation SOR-

Bolt Size M24 x 880 mm, Qty - 8 Nos., Suitable for mounting Fitting of Light - 8Nos. 2025-26

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt

assembled on single MCPCB, with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/aluminium pressure die cast powder coated and high

U.V. & corrosion resistance with diffuser housed in aluminium casted body with company SOR-

mark/name 160V to 70V,Power Factor more than 0.95, THD < 15 %, CCT 3000 K to 6500K, 2025-26

Luminaire efficacy> 85 umens/watt , LED driver efficiency > 85 % ( fitting required LM-79 & LM-

80 Certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring

loaded mounting clips complete.IP20

(iv) 22-24 watts, Surge-2 KV Cat-lll Each 38 751

(D) LED Strip Light

(i) Minimum 4.8W-120 LED per meter (2 wire, IP-65) with non integral suitable Driver complete SOR-

Cat-lll 2025-26

(E) Under Water Light,12V DC including Driver,IP-67 with die-cast/deep drawn housing with

impact resistance clear toughened glass.

(ii) 12 watts Cat-lll Each 0 1022

G) Step Light having Aluminium die cast and ABS Plastic material. SOR-

(i) 5 watts, Direct/Indirect luminaire Cat-lll 2025-26

TOTAL FOR LIGHT FIXTURE CARRIED OVER TO SUMMARY

60W Post Top Lantern LED fitting comprises of finish cast aluminum spigot and spun aluminum

1 MR canopy fixed with opal polycarbonate, pipe arrangement for vertical mounting driver and Each 0 10916 0 MR

accessories wired upto terminal block.IP

SITC of 30-40W Height 4200mm, Light Distribution 360° diffuser height 2310mm Electronic

driver ON/OFFLight Column. IP rating IP65, IK-10, Colour Temperature : 3000K Light Distribution

: Symmetrical, Extruded aluminium bottom ribbed pipe (grade 6063 with test certificate) Ø166 x

3mm thickness & die-cast aluminium top cover. SS fasteners. Pre treated silicone gaskets. PDC

aluminium service door 348mm height x 110mm width at 338mm height above the base plate

shall be provided with the company logo embossed on the bottom of the door and safety rope.

The control gear tray is prewired with 2.5 Sq.mm cable, 6A MCB and 32A terminal connectors

for loop-in / loop-out arrangement. MS mounting plate Sq. 250 x 12mm thick steel of grade

E250 to IS 2062:2011 with 4 elongated holes 38 x 19 to suit M16 bolts at CC180. This mounting

steel plate along with foundation bolts of suitable size to be used for ensuring firm grouting

into the specially designed foundation pole. Hot dip galvanised foundation bolt. Mechanical

resistance IK10.Pure polyester powder coated process : Mild shot blast & pure polyester

powder coating. Translucent polycarbonate diffuser of 3mm thickness with light emission.

Lamp fixed position. This luminaire contains built-in LED modules. LED modules are engineered

accordingly to the existing regulations of Lumen Maintenance (LM80) and Technical

Memorandum (TM21), Lifespan of the luminaire > 60,000 hours at 40°C. Operating ambient

temperature range is from -15°C to +50°C. Driver efficiency >85%, power factor >0.9, THD <10%,

Surge protection 6KV. Column Light.CE and BIS.

Supply, installation, testing and commissioning of tree up lighter Adjustable ground recessed

Led fixture tree up light, 6W LED light for tree up lighter. Fixture shall have Ingress protection

3 MR of IP 65 for the optical part and the driver suitable for exterior grade installations. Make Philips, Each 15 9631 144465 MR

Havells /Crompton specifications to be approved by consultant before procurement.

foundation included as required

Supply, installation, testing and commissioning of in ground recessed Led fixture light, 12W LED

light. Fixture shall have Ingress protection of IP 65 for the optical part and the driver suitable for

4 MR exterior grade installations. Make Philips, Havells /Crompton specifications to be approved by Each 15 11897 178455 MR

consultant before procurement. foundation included as required

Supply, installation, testing and commissioning of surface up & down lighter, 6+6W LED light.

Fixture shall have Ingress protection of IP 65 for the optical part and the driver suitable for

5 MR exterior grade installations. Make Philips, Havells /Crompton specifications to be approved by Each 3 10764 32292 MR

consultant before procurement. foundation included as required

TOTAL FOR LIGHT FIXTURE CARRIED OVER TO SUMMARY

ESTIMATE FOR ELECTRICAL WORK

SUBHEAD:ELECTRICALWORK

Description Unit Qty Rate Total Amount Remarks

Description Unit Qty Rate Total Amount Remarks

A BUILDING (Toilet , Guard room & Restaurant)

DISTRIBUTION BOARD & INTERNAL WIRING

DISTRIBUTION BOARD

Providing and erecting Sheet Steel powder coated MCB distribution board - flush /

surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS

1860 3-11-5. 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used) suitable for single phase incoming

and horizontal single phase outgoing

1871 (iii) 8 way, sheet steel double door Ea. 5 1141

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB

DB complete with connections, testing and commissioning etc. as required.

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate

1739 3-10-1.(B) on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box.

confirming to IS 8828/1996 with ISI Mark

1742 Cat.III Single pole Nos. 40 111

Supplying and fixing following rating, double pole, single phase and neutral, 240 volts,

residual current circuit breaker ( RCCB), having a sensitivity current upto 30 milliamperes

in the existing MCB DB complete with connections, testing and commissioning etc as

Total carried over to Summary

INTERNAL WIRING

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both

are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to

mtr length , in below type of pipe erected with 6A Modular type switch / bell push &

11 1-2-1. accessories and earth continuity of following type, erected on PVC / Metallic/Wooden

box, single mounting base frame covered with textured/metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose

/ H.D.Connector as directed.

(g) with 16 swg HGS metal conduit pipe and accessories painted black. erected SOR-

concealed in wall/ceiling complete Cat. III 2025-26

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI

marked 1.1 KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr length,

in below type of pipe erected with 6A Modular type switch and hum free EME step type

1-2-2 electronic fan regulator mounted and accessories with earth continuity of following type

erected on PVC / Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe

erected. with necessary ceiling rose / H.D.Connector as directed.

(g) with 16 swg HGS metal conduit pipe and accessories painted black. erected SOR-

concealed in wall/ceiling complete- Cat. III 2025-26

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be erected concealed in

/flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded

wire of green colour for earth continuity of following size

(B) With 16 swg HGS metal conduit pipe and accessories painted black.

(c) 3 wire 1.5 sq. mm Mtr. 850 147

(d) 3 wire 2.5 sq. mm Mtr. 350 172

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling SOR-

with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for 2025-26

earth continuity of following size

(B) with 16 swg HGS metal conduit pipe and accessories painted black.

(d) 3 wire 4 sq. mm Mtr. 150 202

(e) 3 wire 6 sq. mm Mtr. 75 266

(f) 3 wire 10 sq. mm (use earth wire of 4 sq.mm ) Mtr. 250 389

(i) 4 wire 10 sq. mm (use earth wire of 4 sq.mm ) Mtr. 0 478

Providing & erecting following type of Modular Type Accessories with necessary

connection. As desired by Engineer In charge

(1) 6 Amp. SP one way switch Each 50 27

(2) 16 Amp. SP one way switch Each 15 51

(3) 6/16Amp. Universal socket Each 15 82

(4) 6 A socket Each 15 42

Supplying & erecting 20 Amp 10 KA ‘C Curve’ single pole MCB with 20 Amp. Plug socket,

3-10-6A company fabricated powder coated sheet steel enclosure erected as directed with

[A] Metal Clad Socket with metal clad top

Cat.III Each 4 522

SITC FANS & LIGHT FIXTURES

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt

assembled on single MCPCB, with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/aluminium pressure die cast powder coated and

high U.V. & corrosion resistance with diffuser housed in aluminium casted body with

2-15-3 company mark/name 160V to 270V,Power Factor more than 0.95, THD < 15 %, CCT

3000 K to 6500K, Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring

loaded mounting clips complete.IP20

(iii) 16-20 watts, Surge-2 KV Each 45 584

(H) Mirror Light 9 Watts, wall mounted minimum 1 feet long Each 6 309

Supply, Installation, Testing and Commissioning of suitable 1200 sweep, BEE 5 Star

rated, Ceiling fan with Brush Less Direct Current (BLDC) permanent ferrite magnet Motor,

class of insulation: B, Rust free 3 nos.Aluminium blades, 2 nos. canopies, shackle kit with

earthing provision, copper winding, Power factor not < 0.9, Service Value (CMM/W)

minimum 6.85, Air delivery minimum 215 CMM, 350 RPM,230v (tolerance as per IS : 374-

2019), THD < 10%, with remote unit for Speed Control and all remaining accessories

including safety pin, nut bolts, washers, temperature rise = 75 degree C (Max.), suitable

for 140 to 285 Voltage and rectifier circuit with surge, over current and overload

protection , 50 Hz, Single phase AC Supply, earthing etc. Complete as required.[ Make

shall be approved by Engineer in Charge]

(B) 1200 mm Sweep (48") Each 10 2857

Supplying & erecting single phase approved make industrial exhaust fan suitable for

5-3-4. medium duty ring mounted low noise operation suitable for medium duty having following

dia size and maximum speed in RPM

[B] 380 mm dia 900 RPM Cat.II Each 4 2713

Supplying Table fan approved make A.C. 23OV, 50 c/s. 40 cm. sweep oscillating

5-3-1. complete with 3 mtrs. of 3core round flexible wire and 3 pin plug top. [ Make shall be Each 2 1823

approved by Engineer in Charge]

ESTIMATE FOR ELECTRICAL WORK

SUBHEAD: AUDIO & CCTV SYSTEM WORK

S. DSR/ SOR Total MR Total SOR

Description Unit Qty Rate Remarks

No. RATE Amount Amount

1 AUDIO & CCTV SYSTEM

SUPPLY, INSTALLATION, TESTING & COMISSIONING OF HIGH-SPL FOREGROUND

MUSIC SPEAKER WITH A 8" LF8 DRIVER OR BETTER AND EMB2S EXTENDED HIGH-

FREQUENCY COMPRESSION DRIVER, BIAMPLIFIED 2WAY ARRAY LOUDSPEAKER

SYSTEM; WITH INDIVIDUAL MODULE FREE FIELD FREQUENCY RANGE (-10DB) OF

80HZ - 18KHZ OR BETTER & PEAK POWER HANDLING OF >= 800W LF . THE

LOUDSPEAKER MODULE SHALL HAVE A MAX. SPL (PEAK) OF MF/HF>= 121DB OR

BETTER. IT SHOULD HAVE HORIZONTAL NEAR DISPERSION PATTERN OF 90º OR

BETTER, VERTICAL DISPERSION OF THE ARRAY SHALL BE 60º OR BETTER. THE

MODULES SHALL HAVE A WEATHER RATING OF IP55. including SUPPLY,

INSTALLATION, TESTING & COMMISSIONING OF OEM AU SHAPE MOUNTING

ARRANGEMENT FOR SUSPENSION OR WALL MOUNTING OF THE MODULES

OFFERED ABOVE.MAKES.

SITC OF 8 CHANNEL CLASS D NETWORKABLE POWER AMPLIFIER WITH A MAX

OUTPUT POWER OF 8X500W@8 OHMS, OR BRIDGED MODE OUTPUT POWER OF 4X

1000W @ 8/4 OHMS. 20HZ - 20 KHZ, SNR OF 102DB AND THD + N OF <0.4% WITH

BUILT IN PROTECTION SUCH AS LIMITERS, TEMPERATURE, DC, SHORT CIRCUIT,

45 MR PEAK CURRENT LIMITERS, TURN ON DELAY ETC. BUILT IN DSP FOR MATRIX Nos. 1 251,160.00 251160 MR

ROUTING, SPEAKER EQUALIZATION, DELAYS, ARRAY EQS ETC. COMPLETE WITH

ETHERNET PORT FOR NETWORK CONTROL, PROGRAMMING AND MONITORING.

SHALL OFFER OPTIONAL NETWORK AUDIO CONNECTIVITY (DANTE OR COBRANET)

THROUGH EXPANSION SLOT. .MAKES. JBL

SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF 2 CONDUCTOR

AWG(168 X 34) OXYGEN-FREE BARE COPPER (HIGH CONDUCTIVITY) CABLE NEC

46 MR TYPE CM AND CL3 TYPE FOR AUDIO ONLY WITH DC RESISTANCE: 1.60 Ω/1000FT. Roll. 2 28,704.00 57408 MR

,MUTUAL CAPACITANCE: 22.3PF/FT.,VOLTAGE RATING: 300V,MAXIMUM CURRENT:

17A@25˚C, AND CABLE ROLL PACKING -500 MTR. .MAKES. BELTEN

SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF CAT6 UTP 23AWG

TWISTED PAIR ARMORED CABLE, SUPPORTS GIGABIT ETHERNET (1000 BASET)

STANDARD. OPERATES AT BANDWIDTH OF 250 MHZ. THIS CABLE WELL EXCEEDS

THE REQUIREMENTS OF TIA/EIA-568-C.2.,CONDUCTOR RESISTANCE (DC):

OHM/1000 MTR @20°C MAX,IMPEDANCE: 100±15% OHM AND TEMPERATURE

RATING: -20° TO + 60°C .ROLL PACKING:305 MTR.ENHANCED PERFORMANCE

CABLE FOR TRANSMISSION OF HIGH SPEED DATA, DIGITAL AND ANALOGUE VOICE

AND VIDEO (RGB) SIGNALS ON LANS. MAKES- D-LINK

SITC OF WEATHERISED ENCLOSURE FOR AUDIO AMPLIFIER WITH FRONT DOOR,

FRONT AND BACK ADJUSTABLE MOUNTING RAILS, 1 FAN MOUNTING PROVISION,

TOP AND BOTTOM CABLE ENTRY PROVIDES OPTIMAL FLEXIBILITY FOR CABLE

MANAGEMENT,EASY WALL MOUNT PROVISION, EASY INSTALLATION- STANDING /

WALL MOUNTING OPTION COMPATIBLE WITH INTERNATIONAL STANDARDS AND

ENCLOSURE DIMENSION'S ARE WXDXH (600 X 600 X 340 MM). MAKES- LIBERTY

Supply, Installation, Testing and Comissioning of USB Full HD 1080p@30fps Web Camera,

1/3”, 2.07MP sensor, 60 Degree FOV, built in Mic, 360 degree manual rotation, privacy

shutter, MJPEG compression format, Auto Focus, Auto white balance & other image SOR-

processing algorithms, USB 2.0, BIS, CE,FCC, RoHS certified, 2025-26

[Approved by Competent Authority i.e. not Below the rank of

Executive Engineer ]

SITC of CENTRAL CONTROL UNIT For DCN Next Generation or DCN wireless systems, or

a combination of the two In single-CCU; maximum 245 wired contribution units, plus

wireless delegate units For multi-CCU systems, with up to 30 CCU’s and a total of 4000 SOR-

contribution units Voice activated microphone mode for wired and wireless systems Ethernet 2025-26

connection for configuration and control computers [Approved by Competent Authority i.e. not

Below the rank of Executive Engineer ]

Supply, installation, testing and commissioning of 42" Video Display System with Network

Video Recorder , Live view/Resolution 5MP/3MP/1080p/720p,Motion Detection Control

Privacy Mask Control. USB interface-1 × USB 2.0 and 1 × USB 3.0,Security-HTTPS, SSL,

Watermark, User Authentication, Miscellaneous-N+1 hot spare. Alarm in/out -4 / 1,Network

interface-1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface, Security-HTTPS,

SSL,Video/Audio output-VAG,HDMI and Audio. Watermark, User Authentication,Incoming

bandwidth-100Mbps,Outgoing bandwidth-80Mbps,HDMI output,VGA Output,Protocol-IPv4,

IPv6, TCP/IP protocol, PPPoE, DHCP, DNS, DDNS, NTP, SADP, SMTP, SNMP, NFS, and

iSCSI are supported.TCP, UDP and RTP for unicast, UPnPTM, ONVIF, PSIA,Support 100 IP

Camera, 2 SATA interfaces for 4 HDDs Upto 6TB for each disk. Make-Tyco/Mobotix/Pelco

SITC of 20 x SFP ports

4 x Combo 10/100/1000BASE-T/SFP ports

4 x 10G SFP+ ports

6 kV surge protection on all RJ-45 access ports

Switch Resource Management (SRM) for flexible

management of system resources

Redundant Power Supply (RPS) support SOR-

MPLS L2VPM/L3 VPN support 2025-26

Full L3 routing protocol support including OSPF, BGP, and

ISIS for IPv4/IPv6

SDN-enabled switch, compatible with Openflow

10-GbE SFP+ to SFP+ 1M Direct Attach Cable [Approved

by Competent Authority i.e. not Below the rank of Executive

53 Surge protector for Video & power signal to Safeguard the camera from any kind of Surges Nos 1 3,230.00 3230 MR

54 42U Rack including all accessories as complete as required. Nos 1 90,412.00 90412 MR

55 12U Rack including all accessories as complete as required. Nos 1 36,943.00 36943 MR

SITC of PATCH CORD LC-LC SM DUPLEX LENGTH- 3m

56 7-13-4 [Approved by Competent Authority i.e. not Below the rank of Nos 7 1883 -

Executive Engineer ]s required.

Cat 6 information outlet that should confirm or exceed component specifications TIA/EIA-568-

B.2-1 standards for physical & electrical Specifications, should be fully unshielded type and SOR-

should have the tool less mechanism with inbuilt crimping tool and it should be Third Party 2025-26

certified and tested including G.1. Box & Modular cover plate, (RJ- 45).

SITC of Patch Panel Cat 6 UTP Keystone Type- 24 Port-Fully Loaded

[Approved by Competent Authority i.e. not Below the rank 2025-26

of Executive Engineer ]

Supplying, installing, testing and commissioning of UL Listed ONVIF Compliant 16 channel Network

Video Recorder with 2 SATA HDD Slots with storage of 8 TB storage , Recording Bandwidth up to

320 Mbps , Recording Resolution 8MP(4K) , 5MP ,3MP,2MP,1.3MP,1MP, Alram I/O 16 Ch Alarm in , Nos 1 99,950.00 99950 MR

1Ch Alarm out , Ethernet RJ-45 (1000 Mbps)

BRE Global certified 3c x 1.5 sq.mm Fire Survival armoured cable with Class-2 Copper

conductor as per BS EN 60228, twisted, with Mineral ceramic glass fire barrier tape covered

by an extruded layer of Cross-linkable Low smoke zero halogen (LSZH) insulation as per BS

EN 50363 and 1.SZH inner & outer sheath as per BS:7846. Should retain Circuit integrity as

per clause 26 2e of BS: 5839-1. BRE Global & LPCB-FPC certificates to be provided. Outer

sheath should be Anti-Rodent

60 IP 66 rated whether proof Junction Boxes for Camera Nos 7 6,805.00 47635 MR

61 4-5-8. HDPE Duct (40 mm) complete with all accessories as required. Mtr. 850 107 -

62 Underground/Over ground Laying of HDPE Pipe, OFC/ Power! Data/ Coaxial cables- Mtr. 500 622.00 311000 MR

63 SITC Armoured 6 Core Optical Fiber Cable Single mode for induvial junction connection. RM 400 239.00 95600 MR

64 Supply & laying of Cat-6 Armoured Cable for out door camera RM 1250 66.00 82500 MR

TOTAL FOR CCTV CARRIED OVER TO SUMMARY 2115290

ESTIMATE FOR ELECTRICAL WORK

SUBHEAD:FOUNTAIN WORK

S. DSR/ SOR Total

Description Unit Qty Rate Remarks

No. RATE Amount

Supply, Installation, Testing & Commissioning of Interractive Water Fountain with Multi Colour

Illumination suitable for 7.2mtr dia Fountain Equipment/Nozzles -24no. 23mm Foam jet (Bronze)

with Ball joint (Brass) with Inlet Pipe arrangements as required. Interconnecting Plumbing - between

Pumps and Fountain Nozzles with UPVC pipes (sch 40) & UPVC Fitting(sch 80) and Control Ball

valves (UPVC) as required. Pump -of 1no. Submersible pumpset for Fountain operating on 3phase

415V AC Supply having 760LPM Discharge at 8mtr Head (3HP) & 1no. Submersible pumpset for

Fountain operating on 3phase 415V AC Supply having 1600LPM Discharge at 8mtr Head (7.5HP)

with suitable pipe connection and 2no. stainless steel 304 grade Suction Strainer as required. Pump

make- KIRLOSKAR Illumination - 24no. Stainless steel body Underwater light fitting IP68 grade

operating on 12V DC Supply - 24W LED Bulb RGB including fixing clamps and necessary Looping

Cables within the Pond as required. Interconnecting Control Cables -Submersible cables of

suitable sizes - 2Runs x 4Core x 2.5sqmm Copper Coductor Round Flexible cable and 2Runx

3Core x 4sqmm Copper Coductor Flat Flexible cable and Earthing Conductors including suitable

PVC junction boxes with terminations with suitable PVC Conduit pipes from Fountain Pond to

Control Panel (approximately 30mtr) as required.Cable make- POLYCAB/FINOLEX SS Mesh

Cover-4' x 3' size of wire mesh of size 20mm x 20mm x 2mm thick made up of stainless steel

grade materials and covered with 1mm opening fine mesh (ss304) to protect the pump from the

dust and garbage articles etc,. as required. Music System- Music system consists of 1no. PA

Amplifier with Built-in Digital Player model-TZA-7000DP, 2nos. Box speakers model-SRX 500 with

necessary Junction boxes, Interconnecting wiring between Speakers, PA Amplifier with suitable

wires and PVC coduit pipes & fittings as required. PA system make- AHUJA Fountain Controller

Unit- Outdoor type Control Panel made out of MS sheet including Door with locking arrangement

with powder coated finish along with – 1no. 100A TPN Incoming MCCB, 2nos. Starters with O/L

Relay for Pump, 1no. single preventor, 1no. 2 Pole MCB for Lights, 2no. 230v/12v DC Power

supply for Lights, 2no. RGB Controller Unit for Lights Colour changing, 2no. 24Hrs Timer for

Automatic ON/OFF (for Pump and Light) including Panel wiring etc,.as required. 1SET

Long body Clear Stream jet Nozzle

Nozzle Specification: - Bronze/Gunmetal/Brass 24 NOS.

Supply & Fixing water proof high power LED lights watt, and

9x3=27Watts color changing RGB/Multicolor made out of stainless steel 304gr. 24 NOS.

Make: River Fountain

Solenoid Valve for Nozzle control by PLC and VFD based electrical panel. 24 NOS. Lot. 1 2337946 2337946 MR

DCC Programmable SMPS controller for lights 3 NOS.

Supply, Installation, Testing & Commissioning of Heavy Duty VFD (Variable Frequency Drive) for

HP Pump to generate slow motion 24 NOS.

Supplying installation testing and commissioning of Open well submersible Pump Set with totally

enclosed water filled squirrel cage

induction motor water lubricated with oil seals with sleeves and thrust

bearing having all rotating parts dynamically balanced for silent operation Suitable for three phase

10HZ AC supply Motor Body: CI Pump Body: CI Capacity: 3- HP Three Phase 3 NOS.

Programmable panel with BFD

1. With code-based technology

(new concept in INDIA)

2. Pre-Programmed Technology y general Concept in INDIA These all technology is supported by

our controller. 1 NOS.

Electrical material

Make: - Polycab wires/National/Kalinga complete as per the direction & entire Satisfaction of

Engineer in charge.

(A) Three core flat type 2.5 Square mm

(B) Four Core 1.5 square mm. (C) Two Core 1 square mm. - 1 LOT

Plumbing (Piping) Work: Supplying and Fixing of UPVC, PVC & Pipe (10 & 6 Kg/cm2) of

Make: -Prince/Supreme/Prakash or equivalent confirming to IS

4985:2000 including all UPVC fitting i/c jointing with good quality - 1 JOB

solvent of following sizes. All fixing to be done to the entire satisfaction and sample approved by

Engineer-In-charge.

Audio power amplifier (250 watt) Make -: Stranger / National /Ahuja

OL protection /OV protection / High-fidelity (Hi-Fi) -1 NOS.

Supply and fixing of 50Watts - speakers with etc., complete as per standard specifications. -4 NOS.

SS-304 – 16mm thickness Grating for Nozzle -24 NOS.

Drawing/ Design/Installation /Testing /Commissioning - 1 JOB

FOAM & JET FOUNTAIN 63 Mtr. LONG

Submersible Open well pump 7.5 hp 3 phase high discharge for foam nozzle - 3 NOS.

Geyser Nozzle 1” MOC- Brass - 42 NOS.

Colum Jet Nozzle 1”, MOC - Brass - 8 NOS.

Star Delta Starter Electric Panel for fountain electrical equipment’s - 1 NOS

Submersible Led light colour changing, IP

27-watt, 12 V DC Supply. SS Body - 50 NOS

Step down transformer LED light controller

220/12 v. DC supply. 3 NOS

Necessary electric work as a conducting, wiring, cabling, current water proofing, submersible tape and electric tape. -

Necessary plumbing work, PVC Pipe 10kg pressure and PVC fitting as a Tee, elbow,

MTA, FTA, Socket, wall valve, solvent - 1 JOB

Drawing, Design, Installation & Supervision

Providing, laying and fixing in place fountains including all fixtures like plumbing items for butterfly dome etc as per

drawings and the directions of engineer in charge. - 1 SET

Total for fountains

ESTIMATE FOR ELECTRICAL WORK

S.N. Item Code DESCRIPTION UNIT QUANTITY RATES SOR AMOUNT

1 Supply, Installation, Testing & Commissioning of following size of Grid Tied Solar

Power Plant with

Solar Panels (ALMM approved): Frame Material : Anodized Aluminum alloy

Frame With Twin Wall Profile, Front Cover : High Transmission Low-Iron

Tempered Glass (AR Coated), High efficency and positive power tolerance

Pmax: 0/+5, Module Efficiency should be approx. 19.5%-22%, Normal operating

temperature 45'C, Junction Box with Waterproof IP67 & MC4 Compatible and

Enclosed with Bypass diodes, 100% Electroluminescence test to ensure error

free Modules, Thep. temp. co-efficient of the PV module shall equal or better than

-0.45%/degree C. Solar PV modules of minimum fill factor 75% to be used. Unit

Production:- More than 4.5 Unit /kw /day (Actual)(1Year Avg) With 10 year

Product warranty and 25 year Linear Power Warranty includes all mechanical and SOR-

electrical parameters of the Solar panel. Modules must be complied to the 2025-26

DCR(Domestic content requirements). The Ration of AC to DC is 5:6 for the

Installation capacity which are given in AC KW.

Solar Inverter: MPPT Range: MPPT Range: 80-1000 V , Max efficiency: 97.5% -

98.9%, O/p Frequency: 50/60Hz, Operating Altitude (m) ≤4000, O/p Power

Factor: ~1, O/P THDi: <3%, Operating Tempreture Range: -25~60°C, Integrated

protection of Inverter are Anti-islanding Protection, Input Reverse Polarity

Protection, Insulation Resistor Detection, Ground fault protection, Residual

Current Monitoring Unit, Output Over Current Protection, Output Short Circuit

Protection, Output Over Voltage Protection, PV array string fault Protection.

Protection Degree: IP65, User Interface LCD & APP, Datalogger &

Communication: GPRS / Wi-Fi.

Integrated, Input Reverse Polarity Protection Integrated, Insulation Resistor

Detection Integrated, Residual Current Monitoring Unit Integrated, Output Over

Current Protection Integrated, Output Short Circuit Protection Integrated, Output

Over Voltage Protection Integrated, Protection Degree: IP65, User Interface LCD

& APP,Datalogger & Communication: GPRS / Wi-Fi, Module Mounting Structure:

The mounting (Rectangular pipe / square pipe / circular pipe) with requisite cross

bars, nuts and bolts, etc. shall be Hot deep galvanized with minimum 80micron

coating. The Rectangular / square /circular hollow pipe section used for the

structure should have a minimum thickness of 2.0 mm. other than above, the

material thickness should be minimum 2.5 mm. A certificate of a structural

engineer certifying the strength and stability of the mounting structure to

withstand the weight and wind speed of 150 km/hour throughout the life span of

25 years of the system, shall be submitted by the vendors. Hot Dipped SOR-

Galvanized steel coils. suitable arrangement for base plate for foundation , solar 2025-26

panel mounting, the structure should be suitable for carry the load of solar

panel,wiring, sprinkler system etc. with necessary foundation work/wall mount, j

bolt, anchor fastner etc. the nut bolt used for installtion of stucture should be (SS

304) quality.The ground clearance of the bottom most edge of solar panel shall

not be less than 300 mm to 1200 mm or as per site’s technical/feasibility

a. Column –The minimum section (thickness) should be 60MM*40MM

b. Rafter - The minimum section (thickness) should be 60MM*40MM

c. Purlin - The minimum section (thickness) should be 40MM * 40MM Balane of

System with necessary Swichgears (Suitabel size and protection of ACDB &

DCDB), inter connecting wiring, earthing system as per the CEIG drawing

approval, lightining arrester system as per the CEIG drawing approval, all

(C ) Grid Tied Solar Power System: 11 - 25 kW

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium

2 4-3-4. conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe

of following size of cables

(D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core) meter 350 369

(B) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core) meter 480 215

Making trench in soft soil of suitable width of 90 cm deep for laying cable or locating the SOR-

fault all over the run and back filling the same and making the surface as normal ground. 2025-26

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or required depth for

4 4-5-2. laying any size of cable or locating the fault all over the run and back filling the same and meter 150 62

making the surface as normal ground.

(B) If additional machinery like hammer driller or JCB use [Add] meter 380 295

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same

material at required depth in existing trench for laying of cable. below ground / road

surface for enclosing cable (A)50 mm outer dia

(A) 50 mm outer dia meter 0 62

(C) 90 mm inner Dia. meter 200 95

(D) 120 mm inner Dia. meter 150 136

Supply of Approved make Iron Clad or metal clad four pole change over switch 415V.

confirming to IS of following capacity

ESTIMATE FOR ELECTRICAL WORK

SUBHEAD:SUBMERSIBLE PUMPS

Description Unit Qty Rate Total Amount Remarks

Description Unit Qty Rate Total Amount Remarks

A SCHEDULEITEMS

SUBMERSIBLE PUMPS

S.I.T.C. submersible pump set for bore of 200 mm. dia. or more having 3 phase motor capacity

about 25 H.P. and discharge capacity having . Lifting and Lowering taken extra.

(A) (12 Stage) 472 to 330 L.P.M. discharge at the head 120 to 192 mtrs. suitable for 65 mm SOR-

dia. delivery pipe Cat-III 2025-26

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper

cable approved make of following Size.

(E) 3 Core x 10 Sq. mm. Mtr 400 293

Supplying & erecting ISI Marked (Embossed) following size of “B” Class G.I . Pipe & erecting

as directed by Engineer-in-charge with necessary plumbing as desired.

(C) 40 mm dia Mtr 500 210

TOTAL FOR LIGHT FIXTURE CARRIED OVER TO SUMMARY

ESTIMATE FOR ELECTRICAL WORK

SUBHEAD:WATER COOLER & RO

Description Unit Qty Rate Total Amount Remarks

Description Unit Qty Rate Total Amount Remarks

A SCHEDULEITEMS

WATER COOLER & RO

Providing & Erecting full SS Body (SS 304) Split type water cooler having storage capacity 160 to

175 Ltr.(Tank SS 304) & Cooling capacity 150 ltr. Per hour @ an ambient temp of 350 C.The outlet

temp. of the water should drop by 150C within a hour,The water cooler should be comprising of

hermetically sealed Reciprocating compressor with R134A, fan motor, Copper Condensing unit SOR-

with company fabricated Outdoor Unit water tank surrounded by evaporating coil, thermostats, 2025-26

relay etc.complete with necessary copper tube & Insulation, M.S Chanel Stand with Painting for

water tank & M.S. Powder Coated Stand for Outdoor unit with Installation. With DPELCB and

Way DB Box with accessory Three core Cord for connection.

Supplying & erecting 5 stage single reverse osmosis water purification system with M.S. powder

coated frame, prefilter housing with 'O' ring presediment filter GAC filter, carbon filter suitable

buster DC pump capacity 80 psi, mention with 40 psi inline type post carbon filter auto low & high

pressure switches with following size of storage tank & LPH capacity & erected as directed

[C] 50 Ltr / Hr with 150 psi 2 nos booster pump Each 4 24153

TOTAL FOR LIGHT FIXTURE CARRIED OVER TO SUMMARY

ESTIMATE FOR ELECTRICAL WORK

SUBHEAD : LIGHTING

ANALYSIS OF RATES

60W Post Top Lantern LED fitting comprises of finish cast aluminum spigot and spun aluminum canopy

1 fixed with opal polycarbonate, pipe arrangement for vertical mounting driver and accessories wired upto 1 9635

terminal block.IP

Add Cartage @ 1%

Add for installation 2%

Add for contractors over heads and profit @ 10%

SITC of 40W Height 4200mm, Light Distribution 360° diffuser height 2310mm Electronic driver

ON/OFFLight Column. IP rating IP65, IK-10, Colour Temperature : 3000K Light Distribution : Symmetrical,

Extruded aluminium bottom ribbed pipe (grade 6063 with test certificate) Ø166 x 3mm thickness & die-

cast aluminium top cover. SS fasteners. Pre treated silicone gaskets. PDC aluminium service door 348mm

height x 110mm width at 338mm height above the base plate shall be provided with the company logo

embossed on the bottom of the door and safety rope. The control gear tray is prewired with 2.5 Sq.mm

cable, 6A MCB and 32A terminal connectors for loop-in / loop-out arrangement. MS mounting plate Sq.

250 x 12mm thick steel of grade E250 to IS 2062:2011 with 4 elongated holes 38 x 19 to suit M16 bolts at

2 CC180. This mounting steel plate along with foundation bolts of suitable size to be used for ensuring firm 1 35600

grouting into the specially designed foundation pole. Hot dip galvanised foundation bolt. Mechanical

resistance IK10.Pure polyester powder coated process : Mild shot blast & pure polyester powder

coating. Translucent polycarbonate diffuser of 3mm thickness with light emission. Lamp fixed position.

This luminaire contains built-in LED modules. LED modules are engineered accordingly to the existing

regulations of Lumen Maintenance (LM80) and Technical Memorandum (TM21), Lifespan of the

luminaire > 60,000 hours at 40°C. Operating ambient temperature range is from -15°C to +50°C. Driver

efficiency >85%, power factor >0.9, THD <10%, Surge protection 6KV. Column Light.CE and BIS. Make K-

Lite Model KL-7018/Keselec/Ligman

Add Cartage @ 1%

Add for installation 2%

Add for contractors over heads and profit @ 10%

Supply of tree up lighter Adjustable ground recessed Led fixture tree up light, 6W LED light for tree up

lighter. Fixture shall have Ingress protection of IP 65 for the optical part and the driver suitable for

exterior grade installations. Make Philips, Havells /Crompton specifications to be approved by consultant

before procurement. foundation included as required

Add Cartage @ 1%

Add for installation 2%

Add for contractors over heads and profit @ 10%

Supply of in ground recessed Led fixture light, 12W LED light. Fixture shall have Ingress protection of IP

65 for the optical part and the driver suitable for exterior grade installations. Make Philips, Havells

/Crompton specifications to be approved by consultant before procurement. foundation included as

Add Cartage @ 1%

Add for installation 2%

Add for contractors over heads and profit @ 10%

Supply of surface up & down lighter, 6+6W LED light. Fixture shall have Ingress protection of IP 65 for the

optical part and the driver suitable for exterior grade installations. Make Philips, Havells /Crompton

specifications to be approved by consultant before procurement. foundation included as required

Add Cartage @ 1%

Add for installation 2%

Add for contractors over heads and profit @ 10%

ESTIMATE FOR ELECTRICAL WORK

(C) Post Top Lantern LED fitting comprises of finish cast

aluminum spigot and spun aluminum canopy fixed with opal

2 polycarbonate, pipe arrangement for vertical mounting driver 1 4772.00 4772.00 2-16-2. SOR 2023-24

and accessories wired upto terminal block.IP

(ii)32-40W Cat-III

(e) 1.50 Sq.mm 3 core round PVC sheathed 7 Mtr 44.00 308.00 1-4-5 (E)

packing / Forwarding / loading / unloading 1 No. 25.00 25.00 Lumsump

Transprtation 1 Lot 25.00 25.00 Lumsump

Labour of installation of pole 1 Job 500.00 500.00 Lumsump

Add for contractors over heads and profit @ 10%

FRP/GRP pole 4m

(3) 'B' class (Heavy Duty) frp/grp pole

suitable for base plate mounting

[B] Overall Length of 6.0 meter, Average thickness : 7mm,

Top/Bottom Outside Dia.

76/160mm +/-2.Weight of Pole 21.0 Kg approx. (Without base)

Metal Anchor Base dully frp

claded (Size : 310 Ø * 12mmthk , Mounting hole PCD 260mm *

nos. of 16 Ø hole)

Cable end termination with material 2 No. 52.00 104.00 4.7.1(B) SOR 2023-24

MCB single pole 6A to 25A 1 No. 111.00 111.00 3-10-1.(B SOR 2023-24

SITC of 50MM DWC pipe for cable entry 3 Mtr. 62.00 186.00 4.5.8.(A) SOR 2023-24

packing / Forwarding / loading / unloading 1 No. 200.00 200.00 Lumsump

Transportation 1 Lot 200.00 200.00 Lumsump

Numbering 1 job 114.00 114.00 Citelum O&M tender approved rate

Fastners 1 Lump 150.00 150.00 Lumsump

Labour of installation of pole 1 Job 1500.00 1500.00 Lumsump

Add for contractors over heads and profit @ 10%

FRP/GRP pole 6m

(3) 'B' class (Heavy Duty) frp/grp pole

suitable for base plate mounting

[D] Overall Length of 6.0 meter, Average thickness : 7mm,

Top/Bottom Outside Dia.

76/160mm +/-2.Weight of Pole 21.0 Kg approx. (Without base)

Metal Anchor Base dully frp

claded (Size : 310 Ø * 12mmthk , Mounting hole PCD 260mm *

nos. of 20 Ø hole)

Cable end termination with material 2 No. 52.00 104.00 4.7.1(B) SOR 2023-24

MCB single pole 6A to 25A 1 No. 111.00 111.00 3-10-1.(B SOR 2023-24

SITC of 50MM DWC pipe for cable entry 3 Mtr. 62.00 186.00 4.5.8.(A) SOR 2023-24

packing / Forwarding / loading / unloading 1 No. 200.00 200.00 Lumsump

Transportation 1 Lot 200.00 200.00 Lumsump

Numbering 1 job 114.00 114.00 Citelum O&M tender approved rate

Fastners 1 Lump 150.00 150.00 Lumsump

Labour of installation of pole 1 Job 1500.00 1500.00 Lumsump

Add for contractors over heads and profit @ 10%

[H] Overall Length of 10.0 meter, Average thickness : 9mm,

Top/Bottom Outside Dia. 76/244mm +/-2.Weight of Pole 62.0 Kg

3 approx. (Without base) Metal Anchor Base dully frp 1 34768.00 34768.00 SOR 2023-24

claded (Size : 450 Ø * 18mmthk , Mounting hole PCD 390mm *

nos. of 20 Ø hole

Cable end termination with material 2 No. 52.00 104.00 4.7.1(B) SOR 2023-24

MCB single pole 6A to 25A 1 No. 111.00 111.00 3-10-1.(B SOR 2023-24

SITC of 50MM DWC pipe for cable entry 3 Mtr. 62.00 186.00 4.5.8.(A) SOR 2023-24

packing / Forwarding / loading / unloading 1 No. 1500.00 1500.00 Lumsump

Transportation 1 Lot 500.00 500.00 Lumsump

Numbering 1 job 300.00 300.00 Citelum O&M tender approved rate

Fastners 1 Lump 350.00 350.00 Lumsump

Labour of installation of pole 1 Job 2000.00 2000.00 Lumsump

Add for contractors over heads and profit @ 10%

(A) street Light (IP-65), Surge protection -4KV integral and ,Light

2 must have 440VAC line supply with over-voltage protection. 1 5917.00 5917.00 2-16-2. SOR 2023-24

(iii) Above 60 to 90 watts Cat-III

(e) 1.50 Sq.mm 3 core round PVC sheathed 7 Mtr 44.00 308.00 1-4-5 (E)

packing / Forwarding / loading / unloading 1 No. 25.00 25.00 Lumsump

Transprtation 1 Lot 25.00 25.00 Lumsump

Labour of installation of pole 1 Job 500.00 500.00 Lumsump

Add for contractors over heads and profit @ 10%

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light

2 must have 440VAC line supply with over-voltage protection. 1 9552.00 9552.00 2-16-2. SOR 2023-24

(v) above 120 to 160 watts Cat-III

(e) 1.50 Sq.mm 3 core round PVC sheathed 7 Mtr 44.00 308.00 1-4-5 (E)

packing / Forwarding / loading / unloading 1 No. 25.00 25.00 Lumsump

Transprtation 1 Lot 25.00 25.00 Lumsump

Labour of installation of pole 1 Job 500.00 500.00 Lumsump

Add for contractors over heads and profit @ 10%

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light

2 must have 440VAC line supply with over-voltage protection. 1 10711.00 10711.00 2-16-2. SOR 2023-24

(v) above 200 to 250 watts Cat-III

(e) 1.50 Sq.mm 3 core round PVC sheathed 7 Mtr 44.00 308.00 1-4-5 (E)

packing / Forwarding / loading / unloading 1 No. 25.00 25.00 Lumsump

Transprtation 1 Lot 25.00 25.00 Lumsump

Labour of installation of pole 1 Job 500.00 500.00 Lumsump

Add for contractors over heads and profit @ 10%

ESTIMATE FOR ELECTRICAL WORK

FOUNTAIN ANALYSIS OF RATES

Supply, Installation, Testing & Commissioning of Interractive Water Fountain with Multi Colour Illumination

suitable for 7.2mtr dia Fountain Equipment/Nozzles -24no. 23mm Foam jet (Bronze) with Ball joint (Brass)

with Inlet Pipe arrangements as required. Interconnecting Plumbing - between Pumps and Fountain Nozzles

with UPVC pipes (sch 40) & UPVC Fitting(sch 80) and Control Ball valves (UPVC) as required. Pump -of

1no. Submersible pumpset for Fountain operating on 3phase 415V AC Supply having 760LPM Discharge at

8mtr Head (3HP) & 1no. Submersible pumpset for Fountain operating on 3phase 415V AC Supply having

1600LPM Discharge at 8mtr Head (7.5HP) with suitable pipe connection and 2no. stainless steel 304 grade

Suction Strainer as required. Pump make- KIRLOSKAR Illumination - 24no. Stainless steel body Underwater

light fitting IP68 grade operating on 12V DC Supply - 24W LED Bulb RGB including fixing clamps and

necessary Looping Cables within the Pond as required. Interconnecting Control Cables -Submersible cables

of suitable sizes - 2Runs x 4Core x 2.5sqmm Copper Coductor Round Flexible cable and 2Runx 3Core x

4sqmm Copper Coductor Flat Flexible cable and Earthing Conductors including suitable PVC junction boxes

with terminations with suitable PVC Conduit pipes from Fountain Pond to Control Panel (approximately

30mtr) as required.Cable make- POLYCAB/FINOLEX SS Mesh Cover-4' x 3' size of wire mesh of size 20mm x

20mm x 2mm thick made up of stainless steel 304 grade materials and covered with 1mm opening fine mesh

(ss304) to protect the pump from the dust and garbage articles etc,. as required. Music System- Music

system consists of 1no. PA Amplifier with Built-in Digital Player model-TZA-7000DP, 2nos. Box speakers

model-SRX 500 with necessary Junction boxes, Interconnecting wiring between Speakers, PA Amplifier with

suitable wires and PVC coduit pipes & fittings as required. PA system make- AHUJA Fountain Controller Unit-

Outdoor type Control Panel made out of MS sheet including Door with locking arrangement with powder

coated finish along with – 1no. 100A TPN Incoming MCCB, 2nos. Starters with O/L Relay for Pump, 1no.

single preventor, 1no. 2 Pole MCB for Lights, 2no. 230v/12v DC Power supply for Lights, 2no. RGB Controller

Unit for Lights Colour changing, 2no. 24Hrs Timer for Automatic ON/OFF (for Pump and Light) including

Panel wiring etc,.as required. 1SET

Add Cartage @ 1%

Add for installation 2%

Add for contractors over heads and profit @ 10%

FOAM & JET FOUNTAIN 63 Mtr. LONG

Submersible Open well pump 7.5 hp 3 phase high discharge for foam nozzle - 3 NOS.

Geyser Nozzle 1” MOC- Brass - 42 NOS.

Colum Jet Nozzle 1”, MOC - Brass - 8 NOS.

Star Delta Starter Electric Panel for fountain electrical equipment’s - 1 NOS

Submersible Led light colour changing, IP

27-watt, 12 V DC Supply. SS Body - 50 NOS

Step down transformer LED light controller

220/12 v. DC supply. 3 NOS 1 890800

Necessary electric work as a conducting, wiring, cabling, current water proofing, submersible tape and electric tape. -

Necessary plumbing work, PVC Pipe 10kg pressure and PVC fitting as a Tee, elbow,

MTA, FTA, Socket, wall valve, solvent - 1 JOB

Drawing, Design, Installation & Supervision

Providing, laying and fixing in place fountains including all fixtures like plumbing items for butterfly dome etc as per

drawings and the directions of engineer in charge. - 1 SET

Add Cartage @ 1%

Add for installation 2%

Add for contractors over heads and profit @ 10%

Sr.No Description Unit Qty Rate Amount

5 AUDIO SYSTEM ANALYSIS OF RATES

BOQ item no. DESCRIPTION QTY UNIT RATE AMOUNT

5.1 SUPPLY, INSTALLATION, TESTING & COMISSIONING OF HIGH-SPL FOREGROUND MUSIC SPEAKER WITH A 8" LF8 DRIVER OR

BETTER AND EMB2S EXTENDED HIGH-FREQUENCY COMPRESSION DRIVER, BIAMPLIFIED 2WAY ARRAY LOUDSPEAKER

SYSTEM; WITH INDIVIDUAL MODULE FREE FIELD FREQUENCY RANGE (-10DB) OF 80HZ - 18KHZ OR BETTER & PEAK POWER

HANDLING OF >= 800W LF . THE LOUDSPEAKER MODULE SHALL HAVE A MAX. SPL (PEAK) OF MF/HF>= 121DB OR BETTER. IT

SHOULD HAVE HORIZONTAL NEAR DISPERSION PATTERN OF 90º OR BETTER, VERTICAL DISPERSION OF THE ARRAY SHALL BE

60º OR BETTER. THE MODULES SHALL HAVE A WEATHER RATING OF IP55. (MAKE JBL)

SR.NO. DESCRIPTION QTY UNIT RATE AMOUNT

1 Basic price for BGM Outdoor

1 Each Speaker 80000

Add Cartage @ 1% 1%

Add for installation and Unloading 3% 3%

Profit @ 15% 15%

SITC OF 8 CHANNEL CLASS D NETWORKABLE POWER AMPLIFIER WITH A MAX OUTPUT POWER OF 8X500W@8 OHMS, OR

BRIDGED MODE OUTPUT POWER OF 4X 1000W @ 8/4 OHMS. 20HZ - 20 KHZ, SNR OF 102DB AND THD + N OF <0.4% WITH

BUILT IN PROTECTION SUCH AS LIMITERS, TEMPERATURE, DC, SHORT CIRCUIT, PEAK CURRENT LIMITERS, TURN ON DELAY

ETC. BUILT IN DSP FOR MATRIX ROUTING, SPEAKER EQUALIZATION, DELAYS, ARRAY EQS ETC. COMPLETE WITH ETHERNET

PORT FOR NETWORK CONTROL, PROGRAMMING AND MONITORING. SHALL OFFER OPTIONAL NETWORK AUDIO

CONNECTIVITY (DANTE OR COBRANET) THROUGH EXPANSION SLOT. .MAKES. JBL

SR.NO. DESCRIPTION QTY UNIT RATE AMOUNT

1 Basic price for power 1Amplifier

Add Cartage @ 1% 1%

Add for installation and Unloading 3% 3%

Profit @ 15% 15%

5.3 SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF 2 CONDUCTOR 12 AWG(168 X 34) OXYGEN-FREE BARE COPPER

(HIGH CONDUCTIVITY) CABLE NEC TYPE CM AND CL3 TYPE FOR AUDIO ONLY WITH DC RESISTANCE: 1.60 Ω/1000FT. ,MUTUAL

CAPACITANCE: 22.3PF/FT.,VOLTAGE RATING: 300V,MAXIMUM CURRENT: 17A@25˚C, AND CABLE ROLL PACKING -500 MTR.

SR.NO. DESCRIPTION QTY UNIT RATE AMOUNT

1 Basic price for 2 Core14.0

sq.mm.oxygen free

Add Cartage @ 1% 1%

Add for installation and Unloading 3% 3%

Profit @ 15% 15%

5.4 SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OF CAT6 UTP 23AWG TWISTED PAIR ARMORED CABLE, SUPPORTS

GIGABIT ETHERNET (1000 BASET) STANDARD. OPERATES AT BANDWIDTH OF 250 MHZ. THIS CABLE WELL EXCEEDS THE

REQUIREMENTS OF TIA/EIA-568-C.2.,CONDUCTOR RESISTANCE (DC): 93.5 OHM/1000 MTR @20°C MAX,IMPEDANCE:

100±15% OHM AND TEMPERATURE RATING: -20° TO + 60°C .ROLL PACKING:305 MTR.ENHANCED PERFORMANCE CABLE FOR

TRANSMISSION OF HIGH SPEED DATA, DIGITAL AND ANALOGUE VOICE AND VIDEO (RGB) SIGNALS ON LANS. MAKES- D-LINK

SR.NO. DESCRIPTION QTY UNIT RATE AMOUNT

1 Basic price for Cat-6 Cable

Add Cartage @ 1% 1%

Add for installation and Unloading 3% 3%

Profit @ 15% 15%

5.6 SITC OF WEATHERISED ENCLOSURE FOR AUDIO AMPLIFIER WITH FRONT DOOR, FRONT AND BACK ADJUSTABLE MOUNTING

RAILS, 1 FAN MOUNTING PROVISION, TOP AND BOTTOM CABLE ENTRY PROVIDES OPTIMAL FLEXIBILITY FOR CABLE

MANAGEMENT,EASY WALL MOUNT PROVISION, EASY INSTALLATION- STANDING / WALL MOUNTING OPTION COMPATIBLE

WITH INTERNATIONAL STANDARDS AND ENCLOSURE DIMENSION'S ARE WXDXH (600 X 600 X 340 MM). MAKES- LIBERTY,

SR.NO. DESCRIPTION QTY UNIT RATE AMOUNT

1 Basic price for Weatherised

1 EachEnclosure 75000

Add Cartage @ 1% 1%

Add for installation and Unloading 3% 3%

Profit @ 15% 15%

Supply of 42" Video Display System with Network Video

Recorder , Live view/Resolution

5MP/3MP/1080p/720p,Motion Detection Control Privacy

Mask Control. USB interface-1 × USB 2.0 and 1 × USB

3.0,Security-HTTPS, SSL, Watermark, User

Authentication, Miscellaneous-N+1 hot spare. Alarm

in/out -4 / 1,Network interface-1 RJ-45 10 /100 /1000

Mbps self-adaptive Ethernet interface, Security-HTTPS,

c SSL,Video/Audio output-VAG,HDMI and Audio. NOS 1.00 406463

Watermark, User Authentication,Incoming bandwidth-

100Mbps,Outgoing bandwidth-80Mbps,HDMI

output,VGA Output,Protocol-IPv4, IPv6, TCP/IP protocol,

PPPoE, DHCP, DNS, DDNS, NTP, SADP, SMTP,

SNMP, NFS, and iSCSI are supported.TCP, UDP and

RTP for unicast, UPnPTM, ONVIF, PSIA,Support 100 IP

Camera, 2 SATA interfaces for 4 HDDs Upto 6TB for

each disk. Make-Tyco/Mobotix/Pelco

Material Cost Rate Sub Total

Add Cartage @ 1% 1%

Add for installation 3% 3%

Profit @ 15% 15%

d 6 TB HDD (Seagate/WD) NOS 1.00 13831

Material Cost Rate Sub Total

Add Cartage @ 1% 1%

Add for installation 3% 3%

Profit @ 15% 15%

Surge protector for Video & power signal to Safeguard the

camera from any kind of Surges

Material Cost Rate Sub Total

Add Cartage @ 1% 1%

Add for installation 3% 3%

Profit @ 15% 15%

42U Rack including all accessories as complete as required.

Material Cost Rate Sub Total

Add Cartage @ 1% 1%

Add for installation 2% 3%

Profit @ 15% 15%

12U Rack including all accessories as complete as required.

Material Cost Rate Sub Total

Add Cartage @ 1% 1%

Add for installation 2% 3%

Profit @ 15% 15%

e Cat 6 information outlet

1.0 Cat 6 information outlet NOS 1.00 579

Material Cost Rate Sub Total

Add Cartage @ 1% 1%

Add for installation 2% 3%

Profit @ 15% 15%

Supplying of UL Listed ONVIF Compliant 16 channel Network

Video Recorder with 2 SATA HDD Slots with storage of 8 TB

2.0 storage , Recording Bandwidth up to 320 Mbps , Recording NOS 1.00 83570

Resolution 8MP(4K) , 5MP ,3MP,2MP,1.3MP,1MP, Alram I/O

16 Ch Alarm in , 1Ch Alarm out , Ethernet RJ-45 (1000 Mbps)

Material Cost Rate Sub Total

Add Cartage @ 1% 1%

Add for installation 2% 3%

Profit @ 15% 15%

BRE Global certified 3c x 1.5 sq.mm Fire Survival armoured

cable with Class-2 Copper conductor as per BS EN

twisted, with Mineral ceramic glass fire barrier tape covered by

an extruded layer of Cross-linkable Low smoke zero halogen

(LSZH) insulation as per BS EN 50363 and 1.SZH inner & outer

sheath as per BS:7846. Should retain Circuit integrity as per

clause 26 2e of BS: 5839-1. BRE Global & LPCB-FPC certificates

to be provided. Outer sheath should be Anti-Rodent

Material Cost Rate Sub Total

Add Cartage @ 1% 1%

Add for installation 2% 3%

Profit @ 15% 15%

j IP 66 rated whether proof Junction Boxes for Camera nos. 1.00 5690

Material Cost Rate Sub Total

Add Cartage @ 1% 1%

Add for installation and Unloading 3% 3%

Profit @ 15% 15%

Underground/Over ground Laying of HDPE Pipe, OFC/ Power!

Data/ Coaxial cables-

Material Cost Rate Sub Total

Add Cartage @ 1% 1%

Add for installation 3% 3%

Profit @ 15% 15%

SITC Armoured 6 Core Optical Fiber Cable Single mode for

induvial junction connection at tower (Make-D-Link)

Material Cost Rate Sub Total

Add Cartage @ 1% 1%

Add for installation and Unloading 3% 3%

Profit @ 15% 15%

Supply & laying of Cat-6 Armoured Cable for out door camera

Material Cost Rate Sub Total

Add Cartage @ 1% 1%

Add for installation and Unloading 3% 3%

Profit @ 15% 15%

Project Name : PROPOSED LAKE AND GARDEN DEVELOPMENT (VILLAGE TALAV) INCLUDING 5 YEARS O & M AT AMBAPUR IN GANDHINAGAR - FOR GANDHINAGAR MUNCIPAL CORPORATION

ESTIMATION FOR LANDSCAPE AUTOMATIC IRRIGATION SYSTEM

I Manual Irrigation Works

S.No Description Units Picture Qty Amount

Installation Rates

Pipes Work: Supply, laying & commissioning in position PVC pipe conforming to IS:4985:2000 and suitable

for the respective working pressures without all fittings and accessories e.g. couplings, tees, bends, reducers,

1.00 Finolex/Supreme

screwed adapters, flanged tail pieces etc., complete, as per the instructions of Architect/Landscape

Architect/Engineer In Charge.

1.01 PVC pipe 75mm-10 kg/cm² - Mainline Finolex/Supreme Rm 252.00 332.00

1.02 PVC pipe 63mm-6 kg/cm² Finolex/Supreme Rm 60.00 167.57

1.03 PVC pipe 50mm-6 kg/cm² Finolex/Supreme Rm 150.00 104.50

1.04 PVC pipe 40mm-6 kg/cm² Finolex/Supreme Rm 762.00 92.50

1.05 PVC pipe 25mm-10 kg/cm² Finolex/Supreme Rm 6.00 61.25

1.06 PVC pipe 20mm-10 kg/cm² Finolex/Supreme Rm 6.00 39.50

1.07 PVC fittings Finolex/Supreme LS -

1.08 Earth work excavation and refilling 300x450mm Rm 1,224.00 90.00

Supply,Fixing & commissioning of 8mm Anchor fasteners, 8mm Threaded Rod, Universal Clamp, Channel,

Threaded U Clamp, for below podium work

ISI Nos RO 390.00 -

Supply,Fixing & commissioning of MS Bracket fabricated from L-Angle with Anchor Bolts as wall/floor

ISI Nos RO 900.00 -

2.00 DRIP & ACCESSORIES

Supply, Fixing & Commissioning of flexible,kink resistant 16mm surface inline tubing and copper shield

technology or Equivalent Technology protects the root intrusion with pressure compensating, self

flushing emitter, brown in colour, UV damage and algae growth with flow rate of 2.3/3.5 lph pressure

2.01 rating 0.58 to 4.14 bar, Dripper Spacing at 30 cm / 45 cm Spacing with 100mm-150mm depth of

earthwork etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge. WITH

RAINBIRD/ EQUIVALENT Rm 1,824.00 80.00

Supply, Fixing & Commissioning of 1" High Flow Inline Pressure Regulators High Flow Inline Pressure

Regulators provide a wider flow range (0.5 gpm to 70 gpm) while delivering reliable pre-set pressure

2.02 regulation protecting the integrity of irrigation systems. , 0.5 gpm (1.9 l/min) to 35 gpm (132.5 l/min)

Regulated Pressure : 40 psi (2.75 bar) , Operating Pressure: 15 psi (1.0 bar) to 150 psi (10.3 bar)

RAINBIRD/SENNINGER Nos RO

Supply, Fixing & Commissioning of 1.5" High Flow Inline Pressure Regulators High Flow Inline Pressure

Regulators provide a wider flow range (0.5 gpm to 70 gpm) while delivering reliable pre-set pressure

2.03 regulation protecting the integrity of irrigation systems.Flow 15 gpm (56.8 l/min) to 70 gpm (265.0 l/min)

Regulated Pressure : 50 psi (3.44 bar) , Operating Pressure: 15 psi (1.0 bar) to 150 psi (10.3 bar)

RAINBIRD/SENNINGER Nos RO

Supply,Fixing & commissioning of 2" Large Capacity Y Type Disc / Screen Filters for submain filteration

Have High Flow & Low Maintenance With a Solid Build,Maximum Flow Up to 110 gpm (25m³/hr), Maximum

2.04 Pressure 116 psi (8 bar),Maximum Temperature Up to 140ºF (60ºC) etc., complete, as per the instructions of

Architect/Landscape Architect/Engineer In Charge.

XERITECH /STF Nos 1.00 3,675.00

Supply,Fixing & commissioning of 1" Large Capacity Y Type Disc / Screen Filters for submain filteration

Have High Flow & Low Maintenance With a Solid Build,Maximum Flow Up to 26 gpm (6m³/hr), Maximum

2.05 Pressure 116 psi (8 bar),Maximum Temperature Up to 140ºF (60ºC) etc., complete, as per the instructions of

Architect/Landscape Architect/Engineer In Charge.

XERITECH /STF Nos 2.00 1,200.00

Supply,Fixing & commissioning of 40mm/50mm/63mm dia self-closing flushing valves that are installed at

the end of the irrigation line for effecting flushing of the line at the beginning of every irrigation cycle, thus

2.06 avoiding the clogging of the emitters /sprinklers through removal of particles, sediments and other impurities

from the water. etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

XERITECH / EQUIVALENT Nos 3.00 200.00

Supply,Fixing & commissioning of 9 - Gauge Galvanized Steel Rod Comes Sharp tips provide easy insertion

into all soil types, Staple Distribution Tubing , XF Drip Line or XBS Tubing to Finished Grade. Notched Sides.

2.07 Corrosion -Resistant of TIE DOWN STAKE etc., complete, as per the instructions of Architect/Landscape

Architect/Engineer In Charge.

XERITECH / EQUIVALENT Nos 912.00 20.00

3.00 SPRINKLERS & ACCESSORIES

Supply,Fixing & commissioning of Pop up spray head1804 SAM PRS Series Spray bodies, with Rotary

nozzle having mutilple stream MPR sprayhaving Co-moulded wiper seal is molded into the cap and features

an encased plastic 'cage' to provide unmatched resitence to grit, nozzle having capable of covering 2.4m -

7.3m at 1.4 - 3.8 Bars pressure, True flushing mechanism,Thick streams and large water droplet & Low

precipitation rate and the enviroment. Additionally, the pressure-activated, multi-function seal design

assures a positive seal without excess'flow-by'which enables more heads to be installed on the same valve,

Two-piece ratchet mechanism, Features is Precision controlled flush at pop-down clears debris from unit,

Construction of time-proven UV_resitant plastic. Pop spray body shall with stand upto 4.8 bar. Built-in Seal-A-

Matic™ (SAM) check valve. Traps water in lateral pipes in elevation changes of up to 14 feet (4.2 m).

PRS Maintains constant outlet pressure at 30 psi or 45 psi at varying inlet pressures.etc., complete, as

per the instructions of Architect/Landscape Architect/Engineer In Charge. 1804 SAM PRS R1724 RAINBIRD/1804 SAM PRS R

Supply,Fixing & commissioning of 1/2" Pop up Connecting Swing joint Assembly , 12" Length . The

tubing shall be made of polyetylene having wall thickness of 2.3mm ,a working pressure of 5.5 kg/cm2 at

43oC and a surge pressure of 16.6 kg/cm2. Flex pipe textured for wet conditions.The fittings shall be made of

3.02 UV resistant thermo plastic etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In

Charge..SA Series.

RAINBIRD / XERITECH Nos 125.00 250.00

Supply,Fixing & commissioning of Imported HDPE service saddle of varying size (40mm,50mm & 63mm

3.03 dia) with pressure rating of PN 10 etc., complete, as per the instructions of Architect/Landscape

Architect/Engineer In Charge. XERITECH / PIMTAS Nos 125.00 200.00

4.00 VALVES & ACCESSORIES

Supply,Fixing & commissioning of PVC Single Union Ball Valve,security pivot to maintain lever in

space,double water tight joint,direct injection stem,Stem O-Ring, non mechanical ,ball Seals with backing

4.01 seals and with a base which permits maximum penetration into the valve of size 63mm with pressure rating

PN 10 etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

PIMTAS / XERITECH Nos 2.00 1,480.00

Supply,Fixing & commissioning of PVC Single Union Ball Valve,security pivot to maintain lever in

space,double water tight joint,direct injection stem, Stem O-Ring, non mechanical ,ball Seals with backing

seals and a base which permits maximum penetration into the valve of size 50mm. with pressure rating PN

4.02 10 etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

PIMTAS / XERITECH Nos 2.00 1,130.00

Supply,Fixing & commissioning of PVC Single Union Ball Valve,security pivot to maintain lever in

space,double water tight joint,direct injection stem,Stem O-Ring, non mechanical ,ball Seals with backing seals

and with a base which permits maximum penetration into the valve of size 40mm. with pressure rating PN

4.03 10 etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

PIMTAS / XERITECH Nos 4.00 960.00

Supply,Fixing & commissioning of a double acting air and vaccum release 1/2 " Air release valve . The Air

release valve shall be capable of both releasing and admitting air from and into the line. The working pressure

shall be 5 bar. Only for Drip Irrigation etc., complete, as per the instructions of Architect/Landscape

4.04 Architect/Engineer In Charge.

XERITECH / RAINBIRD Nos 3.00 750.00

Supply,Fixing & commissioning of a double acting air and vaccum release 2 " Air release valve . The Air

release valve shall be capable of both releasing and admitting air from and into the line. The working pressure

4.05 shall be 10 KSC etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In

XERITECH / HARIT Nos 1.00 2,060.00

Supply,Fixing & commissioning of 6"Round box with greenlid with features Snap-in overlapping lid, Skid-

resistant lid texture,, Body built with three ridges for additional support to sidewallst & Having Dimensions @

Top Opening :6 1/8" Dia & Bottom Opening 8 5/8" Dia etc., complete, as per the instructions of

Architect/Landscape Architect/Engineer In Charge.

RAINBIRD/ PIMTAS / XERITECH Nos 9.00 560.00

Supply,Fixing & commissioning of 10" Round Valve Box with greenlid with features of Overlapping lid with

bolt hole and twist lock, Skid-resistant lid texture, Body built with double ridges for additional sidewall

support & Having Dimensions @ Top Opening 10" Dia & Bottom Opening 12 13/16" Dia etc., complete, as

per the instructions of Architect/Landscape Architect/Engineer In Charge.

RAINBIRD/ PIMTAS / XERITECH Nos 3.00 1,800.00

Supply,Fixing & commissioning of 12" Rectangular Standard Valve Box features, Drop-in lockable lid, Skid-

resistant lid texture, Double ledge lid support, Ridge adds additional support to sidewalls & having

Dimensions @ TTop Opening: 15" L x 9 ½" W Bottom Opening: 18" L x 12 ½" W x 10" H etc., complete, as per

4.08 the instructions of Architect/Landscape Architect/Engineer In Charge.

RAINBIRD/ PIMTAS / XERITECH Nos 5.00 3,100.00

Supply,Fixing & commissioning of 18'' Jumbo Rectangular Standard Valve Box with greenlid and

corrugated structure with unique shovel access slot and bolt hole knockout & having Dimensions @ Top

Opening:18 1/4" L X 13" W & bottom opening :21 1/4" L X 15 15/16"W X 12" H etc., complete, as per the

4.09 instructions of Architect/Landscape Architect/Engineer In Charge.

RAINBIRD/ PIMTAS / XERITECH Nos. 3.00 7,900.00

Supply,Fixing & commissioning of 3/4th inch Quick coupling valve made up of solid brass with locking

cover corrosion resistant and stainless steel spring etc., complete, as per the instructions of

4.1 Architect/Landscape Architect/Engineer In Charge.

XERITECH / EQUIVALENT Nos 5.00 2,000.00

Supply,Fixing & commissioning of 3/4th inch Key threads into top of QCV to provide water access etc.,

complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

XERITECH / EQUIVALENT Nos 1.00 1,100.00

Supply,Fixing & commissioning of 3/4th inch Hose Swivel Made up of Solid Brass Swivels up to

degrees to allows hose to be pulled in any direction & Also to prevent Hose Damage etc., complete, as per

4.12 the instructions of Architect/Landscape Architect/Engineer In Charge.

XERITECH / EQUIVALENT Nos 1.00 1,300.00

Supply,Fixing & commissioning of Imported HDPE service saddle of varying size (75mm to 110mm dia)

with pressure rating of PN 10 etc., complete, as per the instructions of Architect/Landscape

4.13 Architect/Engineer In Charge.

XERITECH / SAB Nos 9.00 350.00

5.00 FILTRATION UNIT

Supply,Fixing & commissioning of 2.5" Disc Filter with capacity 40m3/Hr having an suitable inlet

connections , to create a helical effect in the incoming water ,spinning particulate in suspension away from the

filtering element and so minimizing cleanings frequency ,3/4" outlet for flushing at bottom of filter &

maximum working pressure of 10 Bars etc., complete, as per the instructions of Architect/Landscape

Architect/Engineer In Charge. ARMAS

XERITECH / STF Nos 1.00 18,000.00

Supply,Fixing & commissioning of Pressure Gauge 2" dial With glycerine filled complete, as per the

5.10 instructions of Architect/Landscape Architect/Engineer In Charge.

XERIETCH / EQUIVALENT Nos 1.00 2,500.00

6.00 PUMPING UNIT

Supply,Fixing & commissioning of Monobloc pumpset of having discharge and head of design flow , UPVC

sch 40 - suction & delivery manifold and mounted on a baseframe with proper supports etc., complete, as per

the instructions of Architect/Landscape Architect/Engineer In Charge.

Duty of Pump : 4.00 LPS

Pressure Head Range = 45-50 Mtr

No. of Pumps : 1 Working + 0 Standby WILO / CROMPTON Nos 1.00 69,000.00

Supply,Fixing & commissioning of suitable control panel (DOL)for pumpset with inbuilt irrigation

controller pump start relay & having the Key features , Manual Mode : Push button On / Off Control

,rugged standard 1.6 mm thickness dust & vermin proof enclosure , high voltage proetction, over load & dry

run protetcion fuse protectionfor controller to pump enable signal , 8 PIN control relay instead of slim relay

6.02 terminal with clamp & sufficient access space , wall mounting clamp provision, digital pump control with

external CT , siemens & switch gears, quality proven products with long life assurance., etc., complete, as per

the instructions of Architect/Landscape Architect/Engineer In Charge.

XERITECH / EQUIVALENT Nos 1.00 20,000.00

Supply ,Fixing & Commissioning of Control Cable for Pump Set - 3 core X 4 / 6 Sq.mm Copper cable based on

6.03 the pump capacity

FINOLEX/POLYCAB Mtr 30.00 410.00

Supply,Fixing & commissioning of 2.5'' control Valve, Butterfly Valve VAN Stone flange & Tail Piece in

mainline for bypass and flow diversion of approved quality with pressure rating of PN 10 etc., complete, as

per the instructions of Architect/Landscape Architect/Engineer In Charge.

XERITECH / PIMTAS Nos 5.00 7,290.00

Supply,Fixing & commissioning of 2.5'' Non Return Valve to prevent back flow have flap type or spring type

6.05 with pressure rating of PN 10 etc., complete, as per the instructions of Architect/Landscape Architect/Engineer

In Charge. XERITECH / PIMTAS Nos 1.00 4,450.00

Supply,Fixing & commissioning of Pressure release valve 2" with pressure setting from 0 to 7 Bar etc.,

complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

XERITECH / ARMAS Nos 1.00 19,800.00

Supply,Fixing & commissioning of Ø50-2" Watermeter - ISO PN 10 - GG 25 etc., complete, as per the

instructions of Architect/Landscape Architect/Engineer In Charge.

XERITECH / BERMAD Nos 1.00 33,500.00

Sub Total Manual Irrigation System

7.00 Automation Equipments

Supply,Fixing & commissioning of 14/1 Awg cable with high molecular weight polyethelene and

applications upto 600volts , temperature upto -55 to+ 60 deg centigrade ,soft drawn bare copper meeting

7.01 ASTM B3, tensile strenth 1400PSI for two way communication betwee nsolenoid valvel and decoders complete

including suitable conduit pipe etc., complete, as per the instructions of Architect/Landscape

Architect/Engineer In Charge. RAINBIRD / PAIGE OR XERITECH PAIGE/XERITECH Mtr 762.00 72.00

Supply,Fixing & Commissioning of PVC pipe 32mm-10 kg/cm² as a conduit pipe -including fittings and

accessories Finolex/Supreme Mtr 762.00 126.25

Supply,Fixing & commissioning of ESP LXME Modular Controller UV resistant basic 8 station and

expandable upto 48stations,wall mount case,with LCD display ,non volatile memory for 100years,10KV surge

protectionwith removable front panel and programmable under battery in office,and flow watch options to

shutdown system if any damage or excess flow or dry run shutdown,cycle+soak,raindelay,station delay ,alarm

light ,electronic diagnostic circuit breaker ,program summary and review, Station Priorities, wiring

test,,4programm and 8start time per program with adjustable delay between stations,6 languages,slow

closing valve, removable battery,and sensor terminals, Power Management and Flow Management ESPseries

Flow Problem Shut Down- yes, Reset User Definable Options - No Auto Reenable or Reenable with adjustable

timer from 1 minute to 24 hours ,One Number of Flow Sensors optional with FSM Flow Smart Module,PIN

Code Protection with IQ Advanced Programming Featurte Pack Software,Flow Settling Time can Adjustable

from 3 to 10 minutes, High Flow Reaction Set Point Adjustable in 1% increments from 105% to 200%,Low

Flow Reaction Set Point Adjustable in 1% increments from 1% to 95% etc., complete, as per the instructions of ESPLXME Nos 1.00 47,000.00

Architect/Landscape Architect/Engineer

Supply,Fixing & commissioning of 1" In Charge. With

Solenoid globeESP-LXME ControlD

angle inlet ValvesESP LXMSM8/ESP

fabric reinforced Nitrile

diaphram Material and rugged PVC construction ,compatible and slow closing to prevent water

hammer,pressure rating upto 10.4 KSC and maximum flow of 40GPM ,max water temp. upto 42degree

centigrade, with 24AC solenoid,current rating 0.41A @50Hz,coil resistance 30ohm with provision to attach

PRS-Dial PGA Pressure Regulation Optional PRS-D etc., complete, as per the instructions of

Architect/Landscape Architect/Engineer In Charge. RAINBIRD/PGA Nos 4.00 3,900.00

Supply,Fixing & commissioning of 1.5" Solenoid globe angle inlet Valves with fabric reinforced Nitrile

diaphram Material and rugged PVC construction ,compatible and slow closing to prevent water

hammer,pressure rating upto 10.4 KSC and maximum flow of 100GPM ,max water temp. upto 42degree

centigrade, with 24AC solenoid,current rating 0.41A @50Hz,coil resistance 30ohm with provision to attach

PRS-Dial PGA Pressure Regulation Optional PRS-D etc., complete, as per the instructions of

Architect/Landscape Architect/Engineer In Charge. RAINBIRD/PGA Nos 2.00 5,700.00

Supply,Fixing & commissioning of 2" Solenoid globe angle inlet Valves with fabric reinforced Nitrile

diaphram Material and rugged PVC durable glass -filled nylon construction ,compatible with and slow

7.06 closing to prevent water hammer,pressure rating upto 10.4 KSC and maximum flow of 150GPM ,max

water temp. upto 42degree centigrade, with 24AC solenoid,current rating 0.41A @50Hz,coil resistance 30ohm

with provision to attach PRS-Dial PGA Pressure Regulation Optional PRS-D etc., complete, as per the RAINBIRD/PGA Nos 2.00 6,700.00

Supply,Fixing & commissioning of PRS-DIAL to Maintain constant outlet pressure between 1.04 to6.9 KSC

7.07 etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

RAINBIRD PRS Nos 8.00 5,800.00

Supply,Fixing & commissioning of direct bury -on wire connector with strain relief ,UL486 D certified

,with waterproof silicon sealant ,fits wire from 22ga to6 ga as per specifications etc., complete, as per the

instructions of Architect/Landscape Architect/Engineer In Charge. DBRY

RAINBIRD DBRY Nos 32.00 260.00

Supply,Fixing & commissioning of SMRTY moisture sensing device ,to measure soil temp,EC ,Moisture level

complete to convert as smart controller,with corrossion resistant sensor and setting thershhold moisture

level etc., complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

RAINBIRD SMRTY Nos 25,500.00

Supply,Fixing & commissioning of automatic rain shut off device ,latching hinge with multiple rainfall

7.10 settings 5mm to 20mm UL CUL listed and CE approved etc., complete, as per the instructions of

Architect/Landscape Architect/Engineer In Charge. RSD BEX RAINBIRD RSD BEX Nos 1.00 7,500.00

Supply,Fixing & commissioning of Pump relay 24 AC PLA relay ,Voltage stabilizer to protect the controller

7.11 complete, as per the instructions of Architect/Landscape Architect/Engineer In Charge.

Submission of Shop drawing, As built drawing, Handing over documents, Training for maintenance to

team after commissioning of the system and including Supervision, Transportation charges

Sub Total Automation Irrigation System

Total Manual Irrigation System + Automation Irrigation System

Maintenance of Irrigation Systems for a period of One year (12 Months) from the date of provisional completion of Irrigation system through

OEM trained professional irrigation vendor

Maintenance work 4 visit by irrigation technicians & engineer visit on need basis Month 12.00 20,000.00

Sub Total Manual Irrigation System + Automation Irrigation System + O & M Charges

Grand Total - Manual Irrigation System + Automation Irrigation System

Grand Total - Manual Irrigation System + Automation Irrigation System

1.All the Civil Work, scaffolding and pump room Under Client Scope

2.Core Cutting and Chipping work Under Client Scope

3.Storage location and room Under Client Scope

Payment Terms & Conditions

1. Advance Payment along with PO/WO Pro rata Basis - 10%

2. Against Delivery of materials at site with in 15 days within from the date of invoice Pro rata Basis- 75%

3. Against installtion Pro rata Basis of the system - 10% within 30 days from the date of invoice submission

4.After completion and commisioning the system Pro Rata Basis - 5% within 30 days from the date of invoice submission

NAME OF PROJECT:- PROPOSED LAKE AND GARDEN DEVELOPMENT (VILLAGE TALAV) INCLUDING

YEARS O & M AT AMBAPUR IN GANDHINAGAR - FOR GANDHINAGAR MUNCIPAL CORPORATION

HORTICULTURE BOQ

SL NO. DESCRIPTION UNIT QTY RATE AMOUNT

A SITE PREPARATION

Trenching in ordinary soil up to a depth of 60 cm including

removal and stacking of serviceable materials and then

disposing of surplus soil, by spreading and neatly leveling

1 within a lead of 50 m and making up the trenched area to Cum 809.35 78.10

proper levels by filling with earth or earth mixed with sludge

or / and manure before and after flooding trench with water

(excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty

2 and carriage upto 5 km complete (earth measured in stacks Cum 424.00 515.60

will be reduced by 20% for payment).

Supplying and stacking sludge at site including royalty and

3 carriage upto 5 km complete (sludge measured in stacks will Cum 125.00 294.00

be reduced by 8% for payment).

2.5 Rough dressing the trenched ground including breaking clods.

2.7 Fine dressing of the ground.

Spreading of sludge, dump manure and/or good earth in

2.8 required thickness as per direction of officer-in-charge (cost

pg.n- 83 of sludge, dump manure and/ or good earth to be paid

Mixing earth and sludge or manure in the required proportion

2.9 specified or

pg.n- 83 directed by the Officer-in-charge

Providing & laying Selection no. 1 grass turf with earth

50mm to 60mm thickness of existing ground prepared with

proper level and ramming with required tools wooden and

8 than rolling the surface with light roller make the surface Sqm. 500.00 87.50

smoothen and light watering the same and maintenance for

30 days or more till the grass establish properly, as per

direction of the officer in charge

Preparation of beds for hedging and shrubbery by excavating

60 cm deep and trenching the excavated base to a further

depth of 30 cm, refilling the excavated earth after breaking

clods and mixing with sludge or manure in the ratio of 8:1 (8

parts of stacked volume of earth after reduction by 20%: one

9 2.13 part of stacked volume of sludge or manure after reduction Cum 1038.00 222.85

by 8%), flooding with water, filling with earth if necessary,

watering and finally fine dressing, leveling etc. including

stacking and disposal of materials declared unserviceable and

surplus earth by spreading and leveling as directed, within a

lead of 50 m, lift up to 1.5 m complete (cost of sludge,

Digging holes in ordinary soil and refilling the same with the

excavated earth mixed with manure or sludge in the ratio of

2:1 by volume (2 parts of stacked volume of earth after

reduction by 20% : 1 part of stacked volume of manure after

10 2.14 reduction by 8%) flooding with water, dressing including

removal of rubbish and surplus earth, if any, with all leads

and lifts (cost of manure, sludge or extra good earth if needed

to be paid for separately) :

2.14.1 Holes 90 cm dia, and 90 cm deep Each 67.00 143.10

2.14.2 Holes 60 cm dia, and 60 cm deep Each 2009.00 43.75

2.14.3 Holes 45 cm dia, and 45 cm deep. Each 2761.00 18.70

Plantation of Trees, Shrubs, and Hedge at site i/c watering

11 2.57 and removal of unsaverieable material’s as per direction of

officer in charge (excluding cost of plant & water)

SL NO. DESCRIPTION UNIT QTY RATE AMOUNT

Tree plant Each 67.00 7.30

Shrub plant Each 2009.00 3.65

Ground cover Each 2761.00 2.45

Supply and stacking Avenue plants or equivalent of height

210cm to 240cm in big poly bags of size 25 cm as per

direction of the office-in-charge

TREES Near water

1 MR Providing and stacking of Salix tetra sperma Nos 10.00 250.00

2 7.53 P/L of Mangifera Indica Nos 10.00 55.00

3 7.5 P/L of Azadirachta Indica Nos 10.00 65.00

4 7.73 P/L of Pongamia glabra Nos 10.00 50.00

5 7.3 P/L of Albizia lebbeck Nos 10.00 65.00

6 7.87 P/L of Tectona Grandis Nos 10.00 110.00

7 7.63 P/L of phoenix sylvetrix Nos 13.00 650.00

8 MR P/L of Ravenala madagascariensis Nos 10.00 350.00

Evergreen Trees

9 7.25 Providing and stacking of Erythrina Indica nos 5.00 65.00

Providing and stacking of Cassia Fistula of height 165-180

10 7.16 cm. with 3-4 branches and thick stem in big size HDPE bags nos 3.00 65.00

as per direction of the officer-in-charge.

Providing and stacking of Cassia javanics of height 120-150

11 7.18 cm. with 3-4 branches and thick stem in big size HDPE bags nos 2.00 85.00

as per direction of the officer-in-charge.

12 7.19 Providing and stacking of Cassia nadoosa nos 2.00 65.00

Providing and stacking of milingtonia of height 45-60 cm. in

13 7.57 earthen pot of size 20 cm as per direction of the officer-in- nos 1.00 70.00

14 7.81 Providing and stacking of Kusum nos 3.00 70.00

15 MR Providing and stacking of Guaiacum officinale nos 1.00 350.00

16 7.7 Providing and stacking of thespesia nos 1.00 80.00

Tall Decidus tree

17 7.23 Providing and stacking Dalbergia Sissoo nos 8.00 55.00

18 mr Providing and stacking Samanea saman nos 8.00 70.00

19 7.9 Providing and stacking of Bombax ceiba nos 7.00 70.00

20 7.82 Providing and stacking of spathodea companulata nos 6.00 75.00

21 7.4 Providing and stacking of Alstonia scholaris nos 6.00 65.00

22 7.24 Providing and stacking of Delonix regia nos 3.00 60.00

Providing and stacking of Jacaranda Mimosaefolia of height

23 7.48 150-165 cm. in big polybags of size 25 cm as per direction of nos 3.00 60.00

the officer-in-charge.

Providing and stacking of Lagerstroemia flos-reginae of

24 7.50 height 150-165 cm. in big poly bag of size 25 cm as per nos 3.00 120.00

direction of the officer-in-charge.

25 7.70 Providing and stacking of Bauhinia blakeana nos 3.00 80.00

26 7.8 Providing and stacking of purpurea nos 2.00 50.00

27 MR Providing and stacking of bauhinia alba nos 2.00 250.00

28 MR Providing and stacking of Terminalia mantaly nos 10.00 650.00

29 MR Providing and stacking of Terminalia mantaly varg. nos 0.00 650.00 -

30 MR Providing and stacking of bambusa vulgaris nos 500.00 110.00

31 7.45 Providing and stacking of Silver oak nos 60.00 50.00

SL NO. DESCRIPTION UNIT QTY RATE AMOUNT

Supply of best quality Shrubs grown in pots/ poly bags of

species with their specification- mentioned below, which are

healthy and completely free form all disease, ready for

6.12 Transplanting, inclusive of labour, loading, unloading by

manual means and cartage. All plants tobe approved before

planting by officer-in- charge. The minimum height of plants

to be 45 cms 75 cms depending on the species.

1 Mr Providing & Displaying of Pennisetumsetaceum nos 1500 180

2 Mr Providing & Displaying of Cymbopogon nos 1200 125

Water Plants - Ground Cover

3 MR Providing & Displaying of water hyssop nos 75000 65

4 MR Providing & Displaying of water clover nos 10 110

5 6.21 Providing & Displaying of ophiopogon japonicus nos 10 30

6 6.15 Providing & Displaying of ipomoea batatas nos 10 20

7 MR Providing & Displaying of marsh pennywort nos 10 250

8 MR Providing & Displaying of Gotu kola creeping nos 30000 150

9 MR Providing & Displaying of Portulaca grandiflora nos 350 150

10 MR Providing & Displaying of liriope muscari nos 20 240

11 Mr Providing & Displaying of chrysanthemum indicum nos 500 130

Providing and stacking of zephranthus lily in 20 cm size of

12 3.73 Earthen Pot/Plastic Pot & as per direction of the officer-in- nos 1600 110

13 5.19 Providing & Displaying of Euphorbia milli nos 400 150

14 Mr Providing & Displaying of Ruellia brittoniana dwarf nos 400 90

15 6.11 Providing & Displaying of Dianella tasmannica V nos 2500 30

16 3.89 Providing & Displaying Schefflera arboricola nos 20 120

17 8.46 Providing & Displaying of murraya paniculata nos 400 15

18 8.58 Providing & Displaying of Tabernamontana nos 400 35

19 5.12 Providing & Displaying of leucophyllum frutescens nos 250 200.00

20 7.67 Providing & Displaying of plumbago auriculta nos 20 110

21 8.32 Providing & Displaying of hamelia patens nos 800 50

22 mr Providing & Displaying of ixora coccinea nos 20 280

23 9.1 Providing & Displaying of Allamanda Cathartica nos 1100 45

24 6.7 Providing & Displaying of clerodendrum inerme nos 1100 20

25 4.60 Providing & Displaying of Asiatic lilly hybrid yellow nos 300 129.15

26 4.60 Providing & Displaying of Asiatic lilly hybrid lilly orange nos 400 129.15

27 4.60 Providing & Displaying of Asiatic lilly hybrid red nos 400 129.15

28 MR Providing & Displaying of chyrsopogon zizanioides nos 40 250

29 MR Providing & Displaying of Hibiscus Rosa - sinesis nos 7 270

30 MR Providing & Displaying of hibiscus variegated nos 450 60

31 3.2 Providing & Displaying of Areca palm nos 137 157.80

32 5.14 Providing & Displaying of Cycus revoluta (Sago palm) nos 5 1183.90

33 MR Providing & Displaying of Russelia equisetiformis nos 110 350

34 3.56 Providing & Displaying of Livistona Rotundifolia nos 110 86.10

35 MR Providing & Displaying of Jatropha Integerrima nos 110 330.00

36 MR Providing & Displaying of acorus calamus nos 1400 90.00

37 8.48 Providing & Displaying of Mussanenda Erythrophylla nos 150 110.00

38 5.12 Providing & Displaying of Bougainvillea nos 5 323

39 8.43 Providing & Displaying of Largerstroemia indica nos 58 40

40 5.31 Providing & Displaying of Furcaria nos 5 225

41 8.8 Providing & Displaying of Cassia biflora nos 58 45

42 7.72 Providing & Displaying of Plumeria Rubra nos 25 400

43 9.80 Providing & Displaying of Jasminum grandiflora nos 58 30

44 9.50 Providing & Displaying of Clerodendrum paniculatum nos 58 30

45 3.75 Providing & Displaying of Rhapis Excelsa nos 150 185

SL NO. DESCRIPTION UNIT QTY RATE AMOUNT

46 Mr Providing & Displaying of Chinese plum yellow nos 1500 350

47 Mr Providing & Displaying of colocassia nos 10 175

48 Mr Providing & Displaying of alternanthera sessils nos 10 20

49 Mr Providing & Displaying of guyanese arrowhead nos 10 150

50 Mr Providing & Displaying of Acrorus Calamus nos 10 90

51 Mr Providing & Displaying of Broadleaf Arrowhead nos 10 120

52 Mr Providing & Displaying of Hymenocallis littorials nos 7500 50

53 Mr Providing & Displaying of fern nos 4500 85

54 Mr Providing & Displaying of cyperus papyrus nos 5000 130

55 Mr Providing & Displaying of sweet flag nos 7000 36

56 Mr Providing & Displaying of typha latifolia nos 7000 600

57 Mr Providing & Displaying of egyptian lotus nos 2000 300

Shade loving Shrubs

58 mr Providing & Displaying of Alpinia zerumbet nos 850 250

59 mr Providing & Displaying of sanservieria variegated nos 850 300

Providing and displaying of Schefflera high colour having ht.

25 cm to 30 cm, well developed with fresh & healthy foliage

in 25 cm size of Earthen pot/Plastic pot & as per direction of

the officer-in-charge.

61 mr Providing & Displaying of horsetail plant nos 850 170

62 mr Providing & Displaying of alocasia macrorrhiza nos 850 120

Providing and displaying of Dieffenbachia Mosaic having ht.

30cm to 45 cm with 10-12 leaves, well developed, fresh and

healthy in 25 cm size of Earthen pot/Plastic pot. & as per

direction of the officer-in-charge

64 mr Providing & Displaying of umbrella palm nos 1500 80

65 mr Providing & Displaying of dracaena angustifolia nos 400 350

66 3.69 Providing & Displaying of philodendron selloum nos 2500 162

67 mr Providing & Displaying of agave augustifolia nos 100 280

68 3.72 Providing & Displaying of philodendron xanadu nos 60 184

Providing and displaying of Philodendron moonlight having

ht. 30 cm to 45 cm with 10 to 12 leaves, well developed,

fresh & healthy bright colour leaves in 25 cm size of Earthen

pot/Plastic pot & as per direction of the officer-in-charge.

70 3.26 Providing & Displaying of chamaedorea elegans palm nos 850 108

For Floating wet land

Providing & Displaying of Acorus calamus nos 150 160

Providing & Displaying of Ipomea aquatica nos 150 220

Providing & Displaying of Alpinia purpureta nos 150 350

Providing & Displaying of Imperata Cylindrica nos 150 580

Providing & Displaying of Aeschynomene aspera nos 150 260

Providing & Displaying of Aponogeton Natans nos 150 120

Providing & Displaying of Nymphea pubescens nos 150 380

Providing & Displaying of Nymphea Rubra nos 150 380

F GROUND COVER -

Providing and stacking of lantana depressa of height 15 cm to

1 Mr 20 cm, full of branches and foliage in 15 cm size of Earthen nos 87 110.00

Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of wedelia trilobata, well developed

15 to 20 leaves, full of branches and foliage in 25 cm size of

Earthen Pot/Plastic Pot & as per direction of the officer-in-

Providing and stacking of lantana sellowiana Earthen

Pot/Plastic Pot & as per direction of the officer-in-charge.

SL NO. DESCRIPTION UNIT QTY RATE AMOUNT

Providing and stacking of cuphea ignea, of height 25-30 cm.,

4 Mr full of branches well developed in 15 cm size of Earthen nos 1100 450.00

Pot/Plastic Pot & as per direction of the officer-in-charge..

Providing and stacking of sedum well developed with fresh

5 Mr & healthy in 25 cm size of Earthen Pot/Plastic Pot & as per nos 1100 210.00

direction of the officer-in-charge

Providing and stacking of Ophiopogon, Green/Black full of

6 6.19 leaves in 15 cm size of Earthen Pot/Plastic Pot & as per nos 32700 20.00

direction of the officer-in-charge.

Supply of best quality house plants, hedges & ground cover,

Succulents bulbs & Rizomes, Reeds & Grasses and Acquatic

Plants grown in pots/poly bags of Species with their

specification mentioned below, which are healthy and

Mr completely free from all disease ready for transplanting,

inclusive of Labour, loading, uploading by Manual means

and cartage. All plants to be approved before planting by

Officer in charge. The minimum height of Plants to be 15 cm

to 90 cms depending on the species.

1 mr Providing & Displaying of carpet grass. Nos 200.00 30.00

I miscellaneous

Preparation of mounds of various size and shape by available

excavated / supplied earth in layers not exceeding 20 cm in

1 2.28 depth, breaking clods, watering of each layer, dressing etc., cum 15.00 401.30

lead upto 50 meter and lift upto 1.5 m complete as per

direction of Officer-in-charge.

Supplying and stacking of Coco peat at site including royalty

and carriage upto 5 km complete

J (Maintenance work)

Providing services of Tata 407 vehicle for carriage of purned

branches/leaves of the trees from the pruning site

including loading/unloading lifting upto approved

municipal dumping ground as per direction of Engineer-

in-charge as and when required including cost of Diesel,

Mobil oil, driver and four labours all in uniform with

necessary T&P such as spade, bill hook, rope, tasla, hassion

cloth, safety cones etc., all complete. (Atleast Tempo/Tata

407 should be loaded upto the body mark of

vehicle for counting a trip).