GE/KHU-70/2025-26 SPL REPAIR/ REPLACEMENT OF LT OH CONDUCTORS TO UNDER GROUND CABLE FROM MAIN OFFICE TO COMPO OFFICE AND OFFRS MESS AREA SPL REPAIR TO BLDG NO T-26 AND PROVN OF IRON GRILL FOR OFFICE BLDG WINDOW AT VARIOUS LOC OF AGE BRI KHUMBATHANG

Amount

M&L pre cast PCC (1:3:6) type C1 (using 20mm graded agg) solid block masonry exc 10cm in width or girth and setting CM (1:6) including demolition of PCC as in block walling built in cement mortar complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:4) on any face of brick walls or concrete surfaces, finished even and fair (without using extra cement) including Preparation of new plastered surfaces and applying two coats of cement base paint over a coat of chalk white primer complete all as specified.

Demolition of cement concrete (unreinforced) in ground floor any type and any position and paving including PCC tiles any type n exc (below or above GL) all as specified.

M&L for 75mm thick, cement concrete, type C-2, 1:3:6 (40 mm graded stone aggregate) as in floors & pavings, plinth protection, path, etc. finishing top surface even and Smooth with using extra cement all as specified.

M&L for 25 mm PCC cement concrete type B1 1:2:4 (using 20mm graded aggregate) in floor as PCC padding for tiling etc complete all as specified

S&F Vitrified ceramic tiles 9-10mm thick (Square/rectangular)polished area of each tiles n.exc 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured (Light Shade)cement to match over & incl 20 mm thick screed bed or bedding layer of cement mortar(1:6) for laying floor finishes including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises all as specified and directed

M&L Pre painted galvalume aluminium Zinc coating GI based corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self tapping screws including dismantling of plain/corrugated steel sheeting any gauge, thickness in roof covering complete all as specified and directed.

M&L Pre painted galvalume aluminium Zinc coating GI based plain steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in Ridges/ Valley roof covering /cladding etc to wall fixed with self tapping screws including dismantling of plain/corrugated steel sheeting any gauge, thickness in roof covering complete all as specified and directed.

Roof truss (framed) trussed, purlins crane gantries, rails and fastenings and heavy bracket framing (Beam tee, angle,hollow section, channel,Pipes or flat sections) inclusing distance pieces,cleats etc Fe 410-W (Gde E-250) quality B, complete all as specified and directed.

M&L Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over red lead primed steel surfaces complete all as specified.

M & L 9 mm thick Prelaminated Partical Board interior grade prelamination one side & other side balancing white lamination fixed with nails to timber frame work as in ceiling including dismantling wall and ceilling boards of any description including cover fillets complete.

M & L 11 to12 mm thick Prelaminated Partical Board interior grade prelamination one side & other side balancing white lamination fixed with nails to timber frame work as in wall including dismantling wall and ceilling boards of any description including cover fillets complete.

S&F 2nd class HW plain fillets Square rectangular/triangular in section clean sawn secured with nails sec area exc 06 & n.exc 13 sqcm including dismantling timber fillets, rails, posts rafter purlins under 40 Sqcm in sectional area complete all as specified and directed.

S&F 2nd cl HW plain fillets square rectangular, triangular in section wrought with nails sectional area exc. 3 and n.exc 6 sqcm including dismantling timber fillets, rails, posts rafter purlins under 40 Sqcm in sectional area complete all as specified and directed.

S&F 2nd cl HW plain fillets square rectangular, triangular in section wrought with nails sectional area n'exc. 3 Sqcm as in beadings including dismantling timber fillets, rails, posts rafter purlins under 40 Sqcm in sectional area complete all as specified and directed.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each complete all as specified and directed.

S& F second class hard wood plain, solid straight chowkats and frame, wrought framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including making good disturbed surfaces of wall complete all as specified and directed

S&F 35mm thick second class hard wood plain framed panelled shutters (any number of panels ), with panels of timber flat on both sides (feather edge), or of veneered particle board medium density wood wood particle board with commericial face veneers and fitted to chowkats.

M&L Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

S &F in repair to 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads, in squares n.exc 0.50 Sqm incl. including hacking out old broken glass and putty/beading complete all as specified.

S &F in repair Galvanised mild steel wire cloth 0.48 mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified as in repair.

S&F 18/19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work, including dismantling of boarding, any description,, fixed in any position complete all as specified and directed

S&F in repair Continuous (piano) hinges, mild steel bright finish or electro galvanised with flap (when open) 40 mm, fixed with steel screws complete all as specified.

S&F in repair Hasp and staple of aluminium anodized, safety type, 100mm long, fixed with screws complete all as specified.

Supply & Fixed 600mm long Stainless steel curtain rod with fancy type brackets, side knobs/caps including with all fittings as fixed in repairs and all as specified and directed by Engineer-In-Charge.

S&F 150mm long aluminium, anodised barrel tower bolts of extruded section, all as specified and as directed by the Engr-in-charge.

S&F 100mm Extruded aluminium alloy handle all as specified and as directed by the Engr-in-charge.

S&F Aluminium alloy, anodised, sliding door bolt 250mm length,with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified.

S&F 140 mm Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and as directed.

S&F in repair Aluminium body hydraulically regulated Door closer universal type, suitable for door shutters of 851 to 1000 mm in width & of weight between 61 to 80kg complete all as specified and directed.

M&L Chequered cement concrete coloured tiles 30 cm x 30 cm x 20 mm thick using grey cement and no pigment set over & including 20 mm thick screed bed or bedding layer in cement mortar (1:6) with neat cement and pointed in grey cement mixed with pigment to match the shade of tiles complete all as specified and directed.

M&L for PCC 100 mm thick, type D-2, 1:4:8 (40mm graded aggregate) as in sub-base, complete all as directed.

S&F Framed Work such as grills, gratings, etc. with ends of bars shouldered and/ or riveted, or forged into spikes: framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe290.Gde-E-165 including welding/ fixing with existing window complete all as specified.

Taking down carefully copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceilling roses, pendants , regulators, sockets light fitting etc for taking credit removing from site and making good disturbed surface etc.

Material and labour for point wiring with 1.5 sqmm cable FRLS PVC insulated, unsheathed copper multistranded conductor, 1100 V grade of size 1.5 sqmm including necessary termination board 1.5 Sqmm PVC insulated unsheathed FRLS copper conductor as earthing and connected to common earthing with PVC heavy duty casing caping/PVC conduit ISI marked as rquired at site along with all accessories and making good the disturbed surfaces of wall/ ceiling etc for the following : -

One light point/ one fan point/ Bell Point controlled by one switch

One 3 pin socket outlet, 5 Amp independent

Supply in repair switch piano flush type single pole one way 5 Amps all as specified

Supply in repair switch socket combination multi purpose, 5 amp all as specified

S & Fin repair Ceiling rose 3 plates flush type 6 Amps,250 volts AC ISI marked

All as per item No 2 above but for point wiring for power point with 2.5 Sqmm FRLS PVC insulated unsheathed copper cable 1100 Volt grade drawn through and including PVC casing caping heavy duty ISI marked /heavy duty conduit ISI marked as required at site alongwith accessories with 2.5 Sq mm FRLS PVC insulated unsheathed copper conductor cable as earthing and connected to common earth all as specified.

S & F in repair switch socket combination switch socket outlet 3 pin, 16 amp flush type

S&F in repair wall mounted LED light fitting 1x20 watts AC decorative box type with driver holder including LED tube light , energy efficient type 4 feet long including neccessary conection prewired and making connection with 3 core copper flexible cable of appropriate size from ceilling rose.

S&F warm white/ white LED luminaire 600X600 mm,35/36 watt,220V recessed type lumen output >= 122 lumen per watts , THD < 10% environmental friendly , new generation , aesthetically designed , ultra modern with high brightness SMD LEDs as light source incl inbuilt drivers with high efficiency PMMA diffuser soft glare free light complete suitable for roof ceiling including connecting up with three core flexible copper conductor of suitable size all as specified and directed.

S&F LED security light fitting 35 watts 230 volts AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Supply and fix in repair sheet metal enclosure SPN DB 12 way,single phase 240 volts double door with 200 amp rated bus bar complete all as directed.

Supply and fix for miniature Circuit breaker (MCB) single pole and current carrying caoacity 6 to 32 Amp 240 volt 'C' curve 10 KA in the MCB DB with connection testing and commissioning complete all as specified and directed.

Supply and fix for miniature Circuit breaker (MCB) single pole & neutral 240 volt C curve 10 KA 32 Amps capacity IP 20 in the MCB DB with connection testing and commissioning complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m in depth and getting it out for laying of cable / pole etc in hard/dense soil all as specified.

Returning, filling in, including spreading, leveling watering, and well ramming in layers not exc 25 cm in hard/dense soil all as directed.

Removing excavated material n.exc 50m and depositing where directed at a level exc. 1.5 cm above the starting point all as directed.

Sand cushioning with clean dry sand to cables with layer of sand 8cm before laying of cable and 15cm thick after laying of cable complete all as specified. Note : For payment purpose punned thickness of 18cm shall be measured against spread thickness of 23cm as mentioned in para 19.75 of SSR part-I.

Supplying and laying unreinforced precast concrete cable cover, class HV, type 1 flat of size 250mm x150mm x 40mm placed perpendicular of the cable complete.

Supply laying and testing cable XLPE insulated screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables heavy duty 1100 volts grade with stranded aluminium conductor of size 16 sqmm 2 core.

Material and labour earthing complete with galvanized steel earth plate 60 cm x 60cm x 6.0mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less less than 1.5 mtr filled around with 15 cm thick alternate layers of charcoal dust and salt and connected to earth lead wire 4mm dia (8 SWG) by means of bolt, nut and check nuts and washers of galvanized iron or steel and thimble and other ends of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15mm bore and watering pipe 20mm dia light grade with funnel and wire mesh, pcc 1:3:6 type C-1 in chambers RCC 1:2:4 type B-1 in pit cover reinforced with 8 mm dia deformed bars 15cm center to center both ways all as directed by Engr-In-Charge, complete all as shown in electric plate No 3 of MES SSR Part I

Dismantling of ACSR or AAC Conductor complete all as specified and directed.

Dismantling steel poles/ struts any size transporting to store and stacking complete all as specified and directede.

Dismantling cross arms of MS channel or angle section etc comlete and setting aside for re-use with in 50m complete all as specified and directed.

Dismantling insulators any type and size complete all as specified and directed.

Supply and laying,jointing & testing in replacement of existing unserviceable XLPE insulated, armoured heavy duty electric cable with aluminium conductor,1100 volt grade laid in trenches,ducts,drawn through pipes across the road/path/along poles/floors/equipment etc of size 120 sq mm 3.5 core.

All as per item srl item No. 61 here-in-before but of size 95 sqmm 3.5 core

All as per item srl item No. 61 here-in-before but of size 50 sqmm 3.5 core

All as per item srl item No. 61 here-in-before but of size 35 sqmm 3.5 core

All as per item srl item No. 61 here-in-before but of size 16 sqmm 4 core

Supply and fix in repair GI Pipe Light grade with all connected accessories of sizes 80 mm dia completed as directed for cable protection

Supply and fix in repair GI Pipe Light grade with all connected accessories of sizes 40 mm dia completed as directed for cable protection

Earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below normal ground level connected to and including galvanised iron strip 32 X 6 mm as earthing lead by means of bolts, nuts, check nuts & washers etc made of GI and connected to earthing test point all as shown in electrical plate No. 3 of SSR Part I of 2009.00 & as specified or indicated and testing on completion including exaction/earth work in any type of strata PCC ( 1:3:6 ) type C1 earthing chamber, pre cast slab 50 mm thick in cement concrete ( 1: 2 : 4 ) type B 1 ( reinforced with welded steel wire fabric (XPM) weight not less than 4 Kg / Sqm), funnel with wire mesh, I watering pipe of 20 mm bore medium grade and lugs, including galvanised iron strip 32X6 mm with GI protection pipe of 40 mm medium grade 7.5 meter long, etc complete all as specified.

Deduct Credit for Demolished/Dismantled material Rs (-) 71,210.00 (Minus) as listed in Schedule 'A' Part-II (Credit Schedule) Note : Tenderers will not quote against this item being a tentative amount, to be considered to arrive at the 'Contract Sum'.

M/S MOHD HUSSAIN (BID ID -3459990)

M/s Raj Construction (BID ID -3459989)

M/S Haji Hadi (BID ID -3459901)

M/S ALI MOHD AND SONS (BID ID -3460061)